CQR FP2/GR/EDR

Installation Guide. Connection Details Operation.

The FP2 resettable manual call point is designed to give the user the Any of the following connections may be selected prior to commisioning. Operating the FP2 resettable call point is both easy and positive, giving
flexibility of having a fully resettable manual call point which, as the user total confidence in its use.
standard, offers practically all commonly used switch/monitoring TB2A/B
To operate the call point, first lift up the protective clear polycarbonate First choice for quality Manual Call Point
configuration in the one device. Single pole cover (if fitted), then push the centre of the clear rectangle window.
TB2C/TB3A Technical Specifications
Any of the five monitoring circuits can be selected by either cutting a change over When sufficient pressure is applied to the window it will break. In fact it
TB1C Switch Type Single pole change over switch
link or making connections to an alternative terminal. switch TB3B/C does not break but collapses into the front case. At this point a yellow
high visibility strip will appear, this indicates a successful operation. 10A/250VAC, 5A/30VDC Resistive Load (Max)
The FP2 features as standard, selectable 470 or 680ohm monitoring Contact Rating
The call point will latch in this state with the switch held in its operated 3A/250VAC, 2A/30VDC Inductive Load (Max)
resistors, line blocking diode, clean change over switch or LED TB2A/B For 470ohm resistor cut LK2
INDICATION. With series condition until manually reset. Monitoring
TB2C/TB3A (Yellow wire) Selectable 470 or 680ohm 1 watt carbon film
Refer to the switch mode and connection data for the required moniotring To reset the call point, insert the key provided into the keyhole and turn Resistor
TB1C For 680ohm resistor cut LK3
configuration. resistor TB3B/C (Blue wire) clockwise until the yellow high visibility strip retracts and the rectangle Blocking diode Selectable type IN4001 (50V)
push plate springs forward to its rest position, at this point the switch Selectable red LED (forward facing) with 470ohm
Fitting. LED Indication
will also reset. current limiting resistor and 120ohm bypass resistor
The FP2 may be fitted either using the surface mounting box provided TB2A/B
or a standard deep metal recess box. TB2C/TB3A For blocking diode cut LK1 Terminal Type 2.5mm insertion type, rated 10A/250VAC (2 per switch)
With series
If the surface mounting box is to be used, identify the cable entry points blocking diode TB1C (Green wire) Testing. Mode Selection
Cut link LK1, LK2 or LK3 to select resistor or diode
and remove the knock-outs to enable the fitting of 20mm gland(s). TB3B/C The FP2 manual call point may be operated and rest almost an infinite options
If the interconnecting cables are recessed into the deep metal recess number of times, it is therefore possible to test and confirm successful IP Rating Designed to conform to IP44
box the FP2 will fit directly into the recess box without the need for the TB2A/B operation by actually operating the FP2 in exactly the way that it would Materials Case - ABS Plastic, Actuator - Polycarbonate
With series LED R1 = 470ohm 0.6W be used in an emergency situation.
surface mounting box. TB2C/TB3A
and resistor R2 = 120ohm 0.6W Because of this, testing should follow exactly the same procedure as the CQR Fire & Security, 125 Pasture Road, Moreton, Merseyside, CH46 4TH.
TB1C
circuit TB1A/B operation of the FP2 (as detailed above) United Kingdom
R1 +44 (0)151 606 1000 info@cqr.co.uk www.cqr.co.uk
R2 Version 4: 210818

CQR FP2/GR/EDR
Installation Guide. Connection Details Operation.
The FP2 resettable manual call point is designed to give the user the Any of the following connections may be selected prior to commisioning. Operating the FP2 resettable call point is both easy and positive, giving
flexibility of having a fully resettable manual call point which, as the user total confidence in its use.
standard, offers practically all commonly used switch/monitoring TB2A/B
To operate the call point, first lift up the protective clear polycarbonate First choice for quality Manual Call Point
configuration in the one device. Single pole cover (if fitted), then push the centre of the clear rectangle window.
TB2C/TB3A Technical Specifications
Any of the five monitoring circuits can be selected by either cutting a change over When sufficient pressure is applied to the window it will break. In fact it
TB1C Switch Type Single pole change over switch
link or making connections to an alternative terminal. switch TB3B/C does not break but collapses into the front case. At this point a yellow
high visibility strip will appear, this indicates a successful operation. 10A/250VAC, 5A/30VDC Resistive Load (Max)
The FP2 features as standard, selectable 470 or 680ohm monitoring Contact Rating
The call point will latch in this state with the switch held in its operated 3A/250VAC, 2A/30VDC Inductive Load (Max)
resistors, line blocking diode, clean change over switch or LED TB2A/B For 470ohm resistor cut LK2
INDICATION. With series condition until manually reset. Monitoring
TB2C/TB3A (Yellow wire) Selectable 470 or 680ohm 1 watt carbon film
Refer to the switch mode and connection data for the required moniotring To reset the call point, insert the key provided into the keyhole and turn Resistor
TB1C For 680ohm resistor cut LK3
configuration. resistor TB3B/C (Blue wire) clockwise until the yellow high visibility strip retracts and the rectangle Blocking diode Selectable type IN4001 (50V)
push plate springs forward to its rest position, at this point the switch Selectable red LED (forward facing) with 470ohm
Fitting. LED Indication
will also reset. current limiting resistor and 120ohm bypass resistor
The FP2 may be fitted either using the surface mounting box provided TB2A/B
or a standard deep metal recess box. TB2C/TB3A For blocking diode cut LK1 Terminal Type 2.5mm insertion type, rated 10A/250VAC (2 per switch)
With series
If the surface mounting box is to be used, identify the cable entry points blocking diode TB1C (Green wire) Testing. Mode Selection
Cut link LK1, LK2 or LK3 to select resistor or diode
and remove the knock-outs to enable the fitting of 20mm gland(s). TB3B/C The FP2 manual call point may be operated and rest almost an infinite options
If the interconnecting cables are recessed into the deep metal recess number of times, it is therefore possible to test and confirm successful IP Rating Designed to conform to IP44
box the FP2 will fit directly into the recess box without the need for the TB2A/B operation by actually operating the FP2 in exactly the way that it would Materials Case - ABS Plastic, Actuator - Polycarbonate
With series LED R1 = 470ohm 0.6W be used in an emergency situation.
surface mounting box. TB2C/TB3A
and resistor R2 = 120ohm 0.6W Because of this, testing should follow exactly the same procedure as the CQR Fire & Security, 125 Pasture Road, Moreton, Merseyside, CH46 4TH.
TB1C
circuit TB1A/B operation of the FP2 (as detailed above) United Kingdom
R1 +44 (0)151 606 1000 info@cqr.co.uk www.cqr.co.uk
R2 Version 4: 210818

CQR FP2/GR/EDR
Installation Guide. Connection Details Operation.
The FP2 resettable manual call point is designed to give the user the Any of the following connections may be selected prior to commisioning. Operating the FP2 resettable call point is both easy and positive, giving
flexibility of having a fully resettable manual call point which, as the user total confidence in its use.
standard, offers practically all commonly used switch/monitoring TB2A/B
To operate the call point, first lift up the protective clear polycarbonate First choice for quality
Manual Call Point
configuration in the one device. Single pole cover (if fitted), then push the centre of the clear rectangle window.
TB2C/TB3A Technical Specifications
Any of the five monitoring circuits can be selected by either cutting a change over When sufficient pressure is applied to the window it will break. In fact it
TB1C Switch Type Single pole change over switch
link or making connections to an alternative terminal. switch TB3B/C does not break but collapses into the front case. At this point a yellow
high visibility strip will appear, this indicates a successful operation. 10A/250VAC, 5A/30VDC Resistive Load (Max)
The FP2 features as standard, selectable 470 or 680ohm monitoring Contact Rating
The call point will latch in this state with the switch held in its operated 3A/250VAC, 2A/30VDC Inductive Load (Max)
resistors, line blocking diode, clean change over switch or LED TB2A/B For 470ohm resistor cut LK2
INDICATION. With series condition until manually reset. Monitoring
TB2C/TB3A (Yellow wire) Selectable 470 or 680ohm 1 watt carbon film
Refer to the switch mode and connection data for the required moniotring To reset the call point, insert the key provided into the keyhole and turn Resistor
TB1C For 680ohm resistor cut LK3
configuration. resistor TB3B/C (Blue wire) clockwise until the yellow high visibility strip retracts and the rectangle Blocking diode Selectable type IN4001 (50V)
push plate springs forward to its rest position, at this point the switch Selectable red LED (forward facing) with 470ohm
Fitting. LED Indication
will also reset. current limiting resistor and 120ohm bypass resistor
The FP2 may be fitted either using the surface mounting box provided TB2A/B
or a standard deep metal recess box. TB2C/TB3A For blocking diode cut LK1 Terminal Type 2.5mm insertion type, rated 10A/250VAC (2 per switch)
With series
If the surface mounting box is to be used, identify the cable entry points blocking diode TB1C (Green wire) Testing. Mode Selection
Cut link LK1, LK2 or LK3 to select resistor or diode
and remove the knock-outs to enable the fitting of 20mm gland(s). TB3B/C The FP2 manual call point may be operated and rest almost an infinite options
If the interconnecting cables are recessed into the deep metal recess number of times, it is therefore possible to test and confirm successful IP Rating Designed to conform to IP44
box the FP2 will fit directly into the recess box without the need for the TB2A/B operation by actually operating the FP2 in exactly the way that it would Materials Case - ABS Plastic, Actuator - Polycarbonate
With series LED R1 = 470ohm 0.6W be used in an emergency situation.
surface mounting box. TB2C/TB3A
and resistor R2 = 120ohm 0.6W Because of this, testing should follow exactly the same procedure as the CQR Fire & Security, 125 Pasture Road, Moreton, Merseyside, CH46 4TH.
TB1C
circuit TB1A/B operation of the FP2 (as detailed above) United Kingdom
R1 +44 (0)151 606 1000 info@cqr.co.uk www.cqr.co.uk
R2 Version 4: 210818
 Fig.1 Standard FP2 Connections Example Wiring Details Fig.2 FP2 with LED connection (may not be suitable for all control panels).
LED illuminates when unit is operated
+ve in +ve in +ve in +ve in

+ve
A B C A B C A B C A B C
EOL Resistor From Fire Alarm
TB2 TB2 TB2 EOL Resistor
Control Panel TB2
+ve out See control panel -ve in See control panel
-ve/0v +ve out
+ve
A A A A A A A A
From Fire Alarm +ve out
B TB1 TB3 B B TB1 TB3 B B TB1 TB3 B B TB1 TB3 B
Control Panel
-ve in -ve in -ve out
-ve/0v C C C C C C C C
Cut link for LK1 Cut link for LK1 DO NOT cut links LK1 DO NOT LK1
LK2 470ohm LK2 470ohm 470ohm LK2 470ohm
limiting resistor limiting resistor 590ohm limiting LK2 cut links
(see control panel) LK3 680ohm (see control panel) LK3 680ohm resistor included LK3 680ohm LK3 680ohm
in LED circuit

First FP2 Last FP2 First FP2 Last FP2

Fig.1 Standard FP2 Connections Example Wiring Details Fig.2 FP2 with LED connection (may not be suitable for all control panels).
LED illuminates when unit is operated
+ve in +ve in +ve in +ve in

+ve
A B C A B C A B C A B C
EOL Resistor From Fire Alarm
TB2 TB2 TB2 EOL Resistor
Control Panel TB2
+ve out See control panel -ve in See control panel
-ve/0v +ve out
+ve
A A A A A A A A
From Fire Alarm +ve out
B TB1 TB3 B B TB1 TB3 B B TB1 TB3 B B TB1 TB3 B
Control Panel
-ve in -ve in -ve out
-ve/0v C C C C C C C C
Cut link for LK1 Cut link for LK1 DO NOT cut links LK1 DO NOT LK1
limiting resistor LK2 470ohm limiting resistor LK2 470ohm LK2 470ohm cut links LK2 470ohm
590ohm limiting
(see control panel) LK3 680ohm (see control panel) LK3 680ohm resistor included LK3 680ohm LK3 680ohm
in LED circuit

First FP2 Last FP2 First FP2 Last FP2

Fig.1 Standard FP2 Connections Example Wiring Details Fig.2 FP2 with LED connection (may not be suitable for all control panels).
LED illuminates when unit is operated
+ve in +ve in +ve in +ve in

+ve
A B C A B C A B C A B C
EOL Resistor From Fire Alarm
TB2 TB2 TB2 EOL Resistor
Control Panel TB2
+ve out See control panel -ve in See control panel
-ve/0v +ve out
+ve
A A A A A A A A
From Fire Alarm +ve out
B TB1 TB3 B B TB1 TB3 B B TB1 TB3 B B TB1 TB3 B
Control Panel
-ve in -ve in -ve out
-ve/0v C C C C C C C C
Cut link for LK1 Cut link for LK1 DO NOT cut links LK1 DO NOT LK1
limiting resistor LK2 470ohm limiting resistor LK2 470ohm LK2 470ohm cut links LK2 470ohm
590ohm limiting
(see control panel) LK3 680ohm (see control panel) LK3 680ohm resistor included LK3 680ohm LK3 680ohm
in LED circuit

First FP2 Last FP2 First FP2 Last FP2