Scope TC 8006

AADCO TESTING & RESEARCH LABORATORY PVT. LTD.
, F 28, BULANDSHAHAR ROAD

Laboratory Name :
INDUSTRIAL AREA, GHAZIABAD, UTTAR PRADESH, INDIA
Accreditation Standard ISO/IEC 17025:2017
Certificate Number TC-8006 Page No 1 of 88
Validity 28/10/2022 to 27/10/2024 Last Amended on 04/02/2023
Component, parameter or Test Method Specification

characteristic tested / against which tests are
S.No Discipline / Group Materials or Products tested Specific Test Performed / performed and / or the
Tests or type of tests techniques / equipment
performed used
Permanent Facility
CHEMICAL- BUILDING
1 Aggregates Chloride IS 4032
MATERIAL
CHEMICAL- BUILDING
2 Aggregates Dissolved Silica IS:2386(Part-7)
MATERIAL
CHEMICAL- BUILDING
3 Aggregates Reduction in Alkalinity IS:2386 (Part-7)
MATERIAL
CHEMICAL- BUILDING
4 Aggregates Sulphate BS:812(Part-117)
MATERIAL
CHEMICAL- BUILDING
5 Aggregates Sulphate IS 4032
MATERIAL
CHEMICAL- BUILDING
6 Aggregates Water Soluble Chloride BS:812(Part-118)
MATERIAL
CHEMICAL- BUILDING
7 Aggregates Water Soluble Chloride IS 14959(P-2)
MATERIAL
CHEMICAL- BUILDING
8 Composite Cement Insoluble Residue IS 4032
MATERIAL
CHEMICAL- BUILDING
9 Composite Cement Loss On Ignition IS 4032
MATERIAL
CHEMICAL- BUILDING
10 Composite Cement Magnesium Oxide IS 4032
MATERIAL
CHEMICAL- BUILDING
11 Composite Cement Potassium Oxide IS 4032
MATERIAL
CHEMICAL- BUILDING
12 Composite Cement Sodium Oxide IS 4032
MATERIAL
CHEMICAL- BUILDING
13 Composite Cement Sulphide Sulphur IS 4032
MATERIAL
CHEMICAL- BUILDING
14 Composite Cement Sulphuric Anhydride IS 4032
MATERIAL
CHEMICAL- BUILDING
15 Composite Cement Total Chloride IS 4032
MATERIAL
CHEMICAL- BUILDING
16 Concrete Admixture Ash Content IS 9103
MATERIAL
CHEMICAL- BUILDING
17 Concrete Admixture Chloride Content IS 6925 clause -3
MATERIAL
CHEMICAL- BUILDING
18 Concrete Admixture Dry Material Content IS 9103
MATERIAL
This is annexure to 'Certificate of Accreditation' and does not require any signature.
AADCO TESTING & RESEARCH LABORATORY PVT. LTD., F 28, BULANDSHAHAR ROAD
Laboratory Name :

performed used
CHEMICAL- BUILDING
19 Concrete Admixture pH Value IS 9103
MATERIAL
CHEMICAL- BUILDING
20 Concrete Admixture Relative Density IS 9103
MATERIAL
CHEMICAL- BUILDING
21 Fly Ash Aluminium Oxide IS 1727
MATERIAL
CHEMICAL- BUILDING
22 Fly Ash Available Alkali IS:3812(P-1)
MATERIAL
CHEMICAL- BUILDING
23 Fly Ash Iron Oxide IS 1727
MATERIAL
CHEMICAL- BUILDING
24 Fly Ash Loss On Ignition IS 1727
MATERIAL
CHEMICAL- BUILDING
25 Fly Ash Magnesium Oxide IS 1727
MATERIAL
CHEMICAL- BUILDING
26 Fly Ash Moisture IS 15388
MATERIAL
CHEMICAL- BUILDING
27 Fly Ash Silicon Dioxide IS 1727
MATERIAL
CHEMICAL- BUILDING
28 Fly Ash Sulphur Trioxide IS 1727
MATERIAL
CHEMICAL- BUILDING
29 Fly Ash Total Chloride IS 4032
MATERIAL
CHEMICAL- BUILDING
30 Gypsum Building Plaster Potassium Oxide IS:4032
MATERIAL
CHEMICAL- BUILDING
31 Gypsum Building Plaster Sodium Oxide IS: 4032
MATERIAL
CHEMICAL- BUILDING
32 Hardened Concrete Chloride BS 1881 Part 124
MATERIAL
CHEMICAL- BUILDING
33 Hardened Concrete Chloride Content IS 14959(P-2)
MATERIAL
CHEMICAL- BUILDING
34 Hardened Concrete Sulphate BS 1881 Part-124
MATERIAL
CHEMICAL- BUILDING
35 Micro Silica Loss On Ignition IS 1727
MATERIAL
CHEMICAL- BUILDING
36 Micro Silica Moisture IS 15388
MATERIAL
CHEMICAL- BUILDING
37 Micro Silica Potassium Oxide IS:4032
MATERIAL
Laboratory Name :

performed used
CHEMICAL- BUILDING
38 Micro Silica Silicon Dioxide IS 1727
MATERIAL
CHEMICAL- BUILDING
39 Micro silica Sodium Oxide IS:4032
MATERIAL
CHEMICAL- BUILDING
40 Mortar Chloride BS:1881(Part-124)
MATERIAL
CHEMICAL- BUILDING
41 Mortar Chloride Content IS:14959(Part-2)
MATERIAL
CHEMICAL- BUILDING
42 Mortar Sulphate BS:1881(Part-124)
MATERIAL
CHEMICAL- BUILDING
43 Ordinary Portland Cement Aluminium Oxide IS 4032
MATERIAL
CHEMICAL- BUILDING
44 Ordinary Portland Cement Calcium Oxide IS 4032
MATERIAL
CHEMICAL- BUILDING
45 Ordinary Portland Cement Insoluble Residue IS 4032
MATERIAL
CHEMICAL- BUILDING
46 Ordinary Portland Cement Iron Oxide IS 4032
MATERIAL
CHEMICAL- BUILDING
47 Ordinary Portland Cement Loss On Ignition IS 4032
MATERIAL
CHEMICAL- BUILDING
48 Ordinary Portland Cement Magnesium Oxide IS 4032
MATERIAL
CHEMICAL- BUILDING
49 Ordinary Portland Cement Potassium Oxide IS:4032
MATERIAL
CHEMICAL- BUILDING
50 Ordinary Portland Cement Silicon Dioxide IS 4032
MATERIAL
CHEMICAL- BUILDING
51 Ordinary Portland Cement Sodium Oxide IS:4032
MATERIAL
CHEMICAL- BUILDING
52 Ordinary Portland Cement Sulphuric Anhydride IS 4032
MATERIAL
CHEMICAL- BUILDING
53 Ordinary Portland Cement Total Chloride IS 4032
MATERIAL
CHEMICAL- BUILDING
54 Plaster Of Paris (POP) Or Gypsum Building Plaster Calcium Oxide IS 1288
MATERIAL
CHEMICAL- BUILDING
55 Plaster Of Paris (POP) Or Gypsum Building Plaster Loss On Ignition IS 2547(P-1)
MATERIAL
CHEMICAL- BUILDING Soluble Magnesium Salts as
56 Plaster Of Paris (POP) Or Gypsum Building Plaster IS 2547 Pt-1
MATERIAL MgO
Laboratory Name :

performed used
CHEMICAL- BUILDING
57 Plaster Of Paris (POP) Or Gypsum Building Plaster Sulphur Trioxide IS 1288
MATERIAL
CHEMICAL- BUILDING
58 Portland Slag Cement Insoluble Residue IS 4032
MATERIAL
CHEMICAL- BUILDING
59 Portland Slag Cement Loss On Ignition IS 4032
MATERIAL
CHEMICAL- BUILDING
60 Portland Slag Cement Magnesium Oxide IS 4032
MATERIAL
CHEMICAL- BUILDING
61 Portland Slag Cement Potassium Oxide IS:4032
MATERIAL
CHEMICAL- BUILDING
62 Portland Slag Cement Sodium Oxide IS:4032
MATERIAL
CHEMICAL- BUILDING
63 Portland Slag Cement Sulphide Sulphur IS 4032
MATERIAL
CHEMICAL- BUILDING
64 Portland Slag Cement Sulphuric Anhydride IS 4032
MATERIAL
CHEMICAL- BUILDING
65 Portland Slag Cement Total Chloride IS 4032
MATERIAL
CHEMICAL- BUILDING
66 Portland-Pozzolana Cement Magnesium Oxide IS:4032
MATERIAL
CHEMICAL- BUILDING
67 Portland-Pozzolana Cement Insoluble Residue IS 4032
MATERIAL
CHEMICAL- BUILDING
68 Portland-Pozzolana Cement Loss On Ignition IS 4032
MATERIAL
CHEMICAL- BUILDING
69 Portland-Pozzolana Cement Potassium Oxide IS:4032
MATERIAL
CHEMICAL- BUILDING
70 Portland-Pozzolana Cement Sodium Oxide IS:4032
MATERIAL
CHEMICAL- BUILDING
71 Portland-Pozzolana Cement Sulphuric Anhydride IS 4032
MATERIAL
CHEMICAL- BUILDING
72 Portland-Pozzolana Cement Total Chloride IS 4032
MATERIAL
CHEMICAL- BUILDING
73 Water Proofing Compound Chloride IS 6925
MATERIAL
CHEMICAL- BUILDING
74 Water Proofing Compound pH IS 9103
MATERIAL
Laboratory Name :

performed used
CHEMICAL- METALLIC
75 COATINGS & TREATMENT Anodized Aluminium Section Thickness of Anodic Coating IS 5523
SOLUTIONS
CHEMICAL- METALLIC
76 COATINGS & TREATMENT Metallic Material Mass of zinc coating IS:6745
SOLUTIONS
CHEMICAL- METALLIC
77 COATINGS & TREATMENT Metallic Material Uniformity of coating IS:2633
SOLUTIONS
CHEMICAL- METALS &
78 Alloy Steel Arsenic ASTM E-415
ALLOYS
CHEMICAL- METALS &
79 Alloy Steel Boron ASTM E-415
ALLOYS
CHEMICAL- METALS &
80 Alloy Steel Carbon ASTM E-415
ALLOYS
CHEMICAL- METALS &
81 Alloy Steel Chromium ASTM E-415
ALLOYS
CHEMICAL- METALS &
82 Alloy Steel Copper ASTM E-415
ALLOYS
CHEMICAL- METALS &
83 Alloy Steel Manganese ASTM E-415
ALLOYS
CHEMICAL- METALS &
84 Alloy Steel Molybdenum ASTM E-415
ALLOYS
CHEMICAL- METALS &
85 Alloy Steel Niobium ASTM E-415
ALLOYS
CHEMICAL- METALS &
86 Alloy Steel Nitrogen ASTM E-415
ALLOYS
CHEMICAL- METALS &
87 Alloy Steel Phosphorus ASTM E-415
ALLOYS
CHEMICAL- METALS &
88 Alloy Steel Silicon ASTM E-415
ALLOYS
CHEMICAL- METALS &
89 Alloy Steel Sulphur ASTM E-415
ALLOYS
CHEMICAL- METALS &
90 Alloy Steel Titanium ASTM E-415
ALLOYS
CHEMICAL- METALS &
91 Alloy Steel Vanadium ASTM E-415
ALLOYS
CHEMICAL- METALS &
92 Alloys Steel Carbon IS:228(Part-1)
ALLOYS
Laboratory Name :

performed used
CHEMICAL- METALS &
93 Alloys Steel Chromium IS:228(Part-6)
ALLOYS
CHEMICAL- METALS &
94 Alloys Steel Manganese IS:228(Part-2)
ALLOYS
CHEMICAL- METALS &
95 Alloys Steel Nickel IS:228(Part-5)
ALLOYS
CHEMICAL- METALS &
96 Alloys Steel Nitrogen IS:228(Part-19)
ALLOYS
CHEMICAL- METALS &
97 Alloys Steel Phosphorus IS:228(Part-3)
ALLOYS
CHEMICAL- METALS &
98 Alloys Steel Silicon IS:228(Part-8)
ALLOYS
CHEMICAL- METALS &
99 Alloys Steel Sulphur IS:228(Part-9)
ALLOYS
CHEMICAL- METALS &
100 Aluminium & its alloys Iron IS 504 (Part-2)
ALLOYS
CHEMICAL- METALS &
101 Aluminium & its alloys Magnesium IS 504 (Part-6)
ALLOYS
CHEMICAL- METALS &
102 Aluminium & its alloys Manganese IS 504(Part-5)
ALLOYS
CHEMICAL- METALS &
103 Aluminium & its alloys Silicon IS 504(Part-1)
ALLOYS
CHEMICAL- METALS &
104 Cast Iron Carbon ASTM E-1999
ALLOYS
CHEMICAL- METALS &
105 Cast Iron Carbon IS 12308(P-1)
ALLOYS
CHEMICAL- METALS &
106 Cast Iron Copper ASTM E- 1999
ALLOYS
CHEMICAL- METALS &
107 Cast Iron Manganese ASTM E- 1999
ALLOYS
CHEMICAL- METALS &
108 Cast Iron Manganese IS 12308(P-10)
ALLOYS
CHEMICAL- METALS &
109 Cast Iron Molybdenum ASTM E- 1999
ALLOYS
CHEMICAL- METALS &
110 Cast Iron Nickel ASTM E- 1999
ALLOYS
CHEMICAL- METALS &
111 Cast Iron Phosphorous IS 12308(P-5)
ALLOYS
Laboratory Name :

performed used
CHEMICAL- METALS &
112 Cast Iron Phosphorus ASTM E- 1999
ALLOYS
CHEMICAL- METALS &
113 Cast Iron Silicon ASTM E- 1999
ALLOYS
CHEMICAL- METALS &
114 Cast Iron Silicon IS 12308(P-6)
ALLOYS
CHEMICAL- METALS &
115 Cast Iron Sulphur ASTM E- 1999
ALLOYS
CHEMICAL- METALS &
116 Cast Iron Sulphur IS 12308(P-2)
ALLOYS
CHEMICAL- METALS &
117 Cast Iron Titanium ASTM E- 1999
ALLOYS
CHEMICAL- METALS &
118 Cast Iron Vanadium ASTM E- 1999
ALLOYS
CHEMICAL- METALS &
119 Low Alloy Steel Arsenic ASTM E-415
ALLOYS
CHEMICAL- METALS &
120 Low Alloy Steel Boron ASTM E-415
ALLOYS
CHEMICAL- METALS &
121 Low Alloy Steel Carbon ASTM E-415
ALLOYS
CHEMICAL- METALS &
122 Low Alloy Steel Chromium ASTM E-415
ALLOYS
CHEMICAL- METALS &
123 Low Alloy Steel Copper ASTM E-415
ALLOYS
CHEMICAL- METALS &
124 Low Alloy Steel Manganese ASTM E-415
ALLOYS
CHEMICAL- METALS &
125 Low Alloy Steel Molybdenum ASTM E-415
ALLOYS
CHEMICAL- METALS &
126 Low Alloy Steel Nickel ASTM E-415
ALLOYS
CHEMICAL- METALS &
127 Low Alloy Steel Niobium ASTM E-415
ALLOYS
CHEMICAL- METALS &
128 Low Alloy Steel Phosphorus ASTM E-415
ALLOYS
CHEMICAL- METALS &
129 Low Alloy Steel Silicon ASTM E-415
ALLOYS
CHEMICAL- METALS &
130 Low Alloy Steel Sulphur ASTM E-415
ALLOYS
Laboratory Name :

performed used
CHEMICAL- METALS &
131 Low Alloy Steel Titanium ASTM E-415
ALLOYS
CHEMICAL- METALS &
132 Low Alloy Steel Vanadium ASTM E-415
ALLOYS
CHEMICAL- METALS &
133 Low Alloys Steel Carbon IS:228(Part-1)
ALLOYS
CHEMICAL- METALS &
134 Low Alloys Steel Chromium IS:228(Part-6)
ALLOYS
CHEMICAL- METALS &
135 Low Alloys Steel Manganese IS:228(Part-2)
ALLOYS
CHEMICAL- METALS &
136 Low Alloys Steel Nickel IS:228(Part-5)
ALLOYS
CHEMICAL- METALS &
137 Low Alloys steel Silicon IS:228(Part -8)
ALLOYS
CHEMICAL- METALS &
138 Low Alloys Steel Sulphur IS:228(Part-9)
ALLOYS
CHEMICAL- METALS &
139 Low Alloys teel Phosphorus IS:228(Part-3)
ALLOYS
CHEMICAL- METALS &
140 Mild Steel Arsenic ASTM E-415
ALLOYS
CHEMICAL- METALS &
141 Mild Steel Boron ASTM E-415
ALLOYS
CHEMICAL- METALS &
142 Mild Steel Carbon ASTM E-415
ALLOYS
CHEMICAL- METALS &
143 Mild Steel Carbon IS 228(P-1)
ALLOYS
CHEMICAL- METALS &
144 Mild Steel Chromium IS:228(Part-6)
ALLOYS
CHEMICAL- METALS &
145 Mild Steel Copper ASTM E-415
ALLOYS
CHEMICAL- METALS &
146 Mild Steel Manganese ASTM E-415
ALLOYS
CHEMICAL- METALS &
147 Mild Steel Manganese IS 228(P-2)
ALLOYS
CHEMICAL- METALS &
148 Mild Steel Molybdenum ASTM E-415
ALLOYS
CHEMICAL- METALS &
149 Mild Steel Nickel ASTM E-415
ALLOYS
Laboratory Name :

performed used
CHEMICAL- METALS &
150 Mild Steel Nickel IS:228(Part-5)
ALLOYS
CHEMICAL- METALS &
151 Mild Steel Niobium ASTM E-415
ALLOYS
CHEMICAL- METALS &
152 Mild Steel Phosphorus ASTM E-415
ALLOYS
CHEMICAL- METALS &
153 Mild Steel Phosphorus IS 228(P-3)
ALLOYS
CHEMICAL- METALS &
154 Mild Steel Silicon ASTM E-415
ALLOYS
CHEMICAL- METALS &
155 Mild Steel Silicon IS 228(P-8)
ALLOYS
CHEMICAL- METALS &
156 Mild Steel Sulphur ASTM E-415
ALLOYS
CHEMICAL- METALS &
157 Mild Steel Sulphur IS 228(P-9)
ALLOYS
CHEMICAL- METALS &
158 Mild Steel Titanium ASTM E-415
ALLOYS
CHEMICAL- METALS &
159 Mild Steel Vanadium ASTM E-415
ALLOYS
CHEMICAL- METALS &
160 Plain Carbon Steel Arsenic ASTM E-415
ALLOYS
CHEMICAL- METALS &
161 Plain Carbon Steel Boron ASTM E-415
ALLOYS
CHEMICAL- METALS &
162 Plain Carbon Steel Carbon ASTM E-415
ALLOYS
CHEMICAL- METALS &
163 Plain Carbon Steel Carbon IS:228(Part-1)
ALLOYS
CHEMICAL- METALS &
164 Plain Carbon Steel Chromium ASTM E-415
ALLOYS
CHEMICAL- METALS &
165 Plain Carbon Steel Chromium IS:228(Part-6)
ALLOYS
CHEMICAL- METALS &
166 Plain carbon steel Copper ASTM E-415
ALLOYS
CHEMICAL- METALS &
167 Plain carbon steel Manganese ASTM E-415
ALLOYS
CHEMICAL- METALS &
168 Plain Carbon Steel Manganese IS:228(Part-2)
ALLOYS
Laboratory Name :

performed used
CHEMICAL- METALS &
169 Plain Carbon Steel Molybdenum ASTM E-415
ALLOYS
CHEMICAL- METALS &
170 Plain Carbon Steel Nickel ASTM E-415
ALLOYS
CHEMICAL- METALS &
171 Plain Carbon Steel Nickel IS:228(Part-5)
ALLOYS
CHEMICAL- METALS &
172 Plain Carbon Steel Niobium ASTM E-415
ALLOYS
CHEMICAL- METALS &
173 Plain Carbon Steel Phosphorus ASTM E-415
ALLOYS
CHEMICAL- METALS &
174 Plain Carbon Steel Phosphorus IS;228(Part-3)
ALLOYS
CHEMICAL- METALS &
175 Plain Carbon Steel Silicon ASTM E-415
ALLOYS
CHEMICAL- METALS &
176 Plain Carbon Steel Silicon IS:228(Part-8)
ALLOYS
CHEMICAL- METALS &
177 Plain Carbon Steel Sulphur IS:228(Part-9)
ALLOYS
CHEMICAL- METALS &
178 Plain Carbon Steel Titanium ASTM E-415
ALLOYS
CHEMICAL- METALS &
179 Plain Carbon Steel Vanadium ASTM E-415
ALLOYS
CHEMICAL- METALS &
180 Plain Caron Steel Sulphur ASTM E-415
ALLOYS
CHEMICAL- METALS &
181 Stainless Steel Carbon ASTM E-1086
ALLOYS
CHEMICAL- METALS &
182 Stainless Steel Carbon IS 228(P-1)
ALLOYS
CHEMICAL- METALS &
183 Stainless Steel Chromium ASTM E-1086
ALLOYS
CHEMICAL- METALS &
184 Stainless Steel Chromium IS 228(P-6)
ALLOYS
CHEMICAL- METALS &
185 Stainless Steel Copper ASTM E-1086
ALLOYS
CHEMICAL- METALS &
186 Stainless Steel Manganese ASTM E-1086
ALLOYS
CHEMICAL- METALS &
187 Stainless Steel Manganese IS 228(P-2)
ALLOYS
Laboratory Name :

performed used
CHEMICAL- METALS &
188 Stainless Steel Molybdenum ASTM E-1086
ALLOYS
CHEMICAL- METALS &
189 Stainless Steel Nickel ASTM E-1086
ALLOYS
CHEMICAL- METALS &
190 Stainless Steel Nickel IS 228(P-5)
ALLOYS
CHEMICAL- METALS &
191 Stainless Steel Phosphorus ASTM E-1086
ALLOYS
CHEMICAL- METALS &
192 Stainless Steel Phosphorus IS 228(P-3)
ALLOYS
CHEMICAL- METALS &
193 Stainless Steel Silicon ASTM E-1086
ALLOYS
CHEMICAL- METALS &
194 Stainless Steel Silicon IS 228(P-8)
ALLOYS
CHEMICAL- METALS &
195 Stainless Steel Sulphur ASTM E-1086
ALLOYS
CHEMICAL- METALS &
196 Stainless Steel Sulphur IS 228(P-9)
ALLOYS
CHEMICAL- SOIL AND
197 Soil Carbonates IS 2720(P-23)
ROCK
CHEMICAL- SOIL AND
198 Soil Moisture Content IS 2720(P-2)
ROCK
CHEMICAL- SOIL AND
199 Soil Organic Matter IS 2720(P-22)
ROCK
CHEMICAL- SOIL AND
200 Soil pH Value IS 2720(P-26)
ROCK
CHEMICAL- SOIL AND
201 Soil Specific Electrical Conductivity IS14767
ROCK
CHEMICAL- SOIL AND
202 Soil Total Soluble Sulphate IS 2720(P-27) Clause -2
ROCK
Ash Content( On air dried
203 CHEMICAL- SOLID FUELS Coal IS 1350(P-1)
basis)
Ash Content(On Equilibrated
basis)
205 CHEMICAL- SOLID FUELS Coal Carbon IS 1350(P-4/Sec-1)
Gross Calorific Value (On air
dried basis)
Laboratory Name :

performed used
Gross Calorific Value(On as
received basis)
Gross Calorific Value(On
Equilibrated Basis)
209 CHEMICAL- SOLID FUELS Coal Hydrogen IS 1350(P-4/Sec-1)
Moisture Content( At as
received basis)
Moisture Content(At air dried
basis)
212 CHEMICAL- SOLID FUELS Coal Moisture(At equilibrated basis) IS 1350(P-1)
Net Calorific Value(On air dried
basis)
214 CHEMICAL- SOLID FUELS Coal Nitrogen IS 1350(P-4/Sec-2)
215 CHEMICAL- SOLID FUELS Coal Oxygen IS 1350(P-4/S-1)
216 CHEMICAL- SOLID FUELS Coal Phosphorus IS 1350(P-5)
217 CHEMICAL- SOLID FUELS Coal Sulphur IS 1350(P-3)
218 CHEMICAL- SOLID FUELS Coal Total Moisture IS 1350(P-1)
Volatile Matter (On air dried
basis)
Volatile Matter (On as received
basis)
Volatile Matter (On equilibrated
basis
Ash Content (On air dried
222 CHEMICAL- SOLID FUELS Coke IS 1350(P-1)
basis)
Ash Content (On as received
basis)
Gross Calorific Value (On air
dried basis)
Gross Calorific Value (On as
received basis)
Volatile Matter (On air dried
basis)
Volatile Matter (On as received
basis)
228 CHEMICAL- WATER Construction Water Chlorides as Cl IS 3025(P-32)
Laboratory Name :

performed used
229 CHEMICAL- WATER Construction Water Inorganic Solids IS 3025(P-18)
230 CHEMICAL- WATER Construction Water Organic Solids IS 3025(P-15)
231 CHEMICAL- WATER Construction Water pH Value IS 3025(P-11)
232 CHEMICAL- WATER Construction Water Sulphates as SO3 IS 3025(P-24/ Sec-1)
233 CHEMICAL- WATER Construction Water Suspended Matter IS 3025(P-17)
Volume of 0.02 N H2SO4
234 CHEMICAL- WATER Construction Water required to neutralize 100 ml IS 3025(P-23)
of sample ( Alkalinity)
Volume of 0.02 N NaOH
235 CHEMICAL- WATER Construction Water Required to Neutralize 100 ml IS 3025(P-22)
sample (Acidity)
236 CHEMICAL- WATER Drinking Water Alkalinity IS:3025(Part-23)
237 CHEMICAL- WATER Drinking Water Bicarbonate IS 3025(P-51)
238 CHEMICAL- WATER Drinking Water Calcium IS 3025(P-40)
239 CHEMICAL- WATER Drinking Water Carbonate IS 3025(P-51)
240 CHEMICAL- WATER Drinking Water Chloride IS 3025(P-32)
241 CHEMICAL- WATER Drinking Water Colour IS 3025(P-4)
242 CHEMICAL- WATER Drinking Water Magnesium IS 3025(P-46)
243 CHEMICAL- WATER Drinking Water Odour IS 3025(P-5)
244 CHEMICAL- WATER Drinking Water pH Value IS 3025(P-11)
245 CHEMICAL- WATER Drinking Water Potassium IS:3025(Part -45)
246 CHEMICAL- WATER Drinking Water Sodium IS:3025(Part-45)
IS 3025(P-24/Sec-1) By
247 CHEMICAL- WATER Drinking Water Sulphate
Gravimetric Method
248 CHEMICAL- WATER Drinking Water Total Dissolved Solids IS 3025(P-16)
249 CHEMICAL- WATER Drinking Water Total Hardness IS:3025(Part-21)
250 CHEMICAL- WATER Packaged Drinking Water Alkalinity IS:3025(P-23)
251 CHEMICAL- WATER Packaged Drinking Water Bicarbonate IS:3025(P-51)
252 CHEMICAL- WATER Packaged Drinking Water Calcium IS:3025(P-40)
253 CHEMICAL- WATER Packaged Drinking Water Carbonate IS:3025(P-51)
254 CHEMICAL- WATER Packaged Drinking Water Chloride IS:3025(P-32)
255 CHEMICAL- WATER Packaged Drinking Water Colour IS:3025(P-4)
Laboratory Name :

performed used
256 CHEMICAL- WATER Packaged Drinking Water Magnesium IS:3025(P-46)
257 CHEMICAL- WATER Packaged Drinking Water Odour IS:3025(P-5)
258 CHEMICAL- WATER Packaged Drinking Water pH Value IS:3025(P-11)
259 CHEMICAL- WATER Packaged Drinking Water Potassium IS:3025(P-45)
260 CHEMICAL- WATER Packaged Drinking Water Sodium IS:3025(P-45)
261 CHEMICAL- WATER Packaged Drinking Water Sulphate IS:3025(P-24/Sec-1)
262 CHEMICAL- WATER Packaged Drinking Water Total Dissolved Solids IS:3025(P-16)
263 CHEMICAL- WATER Packaged Drinking Water Total Hardness IS:3025(P-21)
264 CHEMICAL- WATER Reagent Water Colour Retention IS:1070 Annex-A
265 CHEMICAL- WATER Reagent Water Conductivity IS: 3025(Part- 14)
266 CHEMICAL- WATER Reagent Water pH IS:3025(Part-11)
267 CHEMICAL- WATER Reagent Water Total Solids IS:3025(Part-15)
ELECTRICAL- CABLES & Aerial Bunched Cables for working voltage up to and
268 Test for thickness insulation IS 10810 (Part-8)
WIRES including 1100 V
269 Water absorption IS 10810 Part-33
ELECTRICAL- CABLES & Aerial Bunched Cables for working voltage up to and Elongation at break for
270 IS:10810(Part-11)
WIRES including 1100 V insulation (after ageing)
ELECTRICAL- CABLES & Aerial Bunched Cables for working voltage up to and Breaking load test for
271 IS:10810(Part-2)
WIRES including 1100 V messenger conductor
272 Conductor Resistance Test IS:10810(Part-5)
ELECTRICAL- CABLES & Aerial Bunched Cables for working voltage up to and Conductor resistance test
273 IS:10810(Part-5)
WIRES including 1100 V street lighting conductor
ELECTRICAL- CABLES & Aerial Bunched Cables for working voltage up to and Elongation at break for
274 IS:10810( Part- 7)
WIRES including 1100 V insulation (before ageing)
275 High voltage test IS:10810(Part-45)
276 Shrinkage Test IS:10810(Part-12)
ELECTRICAL- CABLES & Aerial Bunched Cables for working voltage up to and Tensile strength test for
277 IS:10810(Part-11)
WIRES including 1100 V insulation (after ageing)
ELECTRICAL- CABLES & Aerial Bunched Cables for working voltage up to and Tensile strength test for
278 IS:10810(Part-7)
WIRES including 1100 V insulation (before ageing)
Laboratory Name :

performed used
ELECTRICAL- CABLES & Aerial Bunched Cables for working voltage up to and Tensile test for Phase/ street
279 IS:10810(Part-2)
WIRES including 1100 V light conductor
280 Volume Resistivity IS:10810(Part-43)
ELECTRICAL- CABLES & Aerial Bunched Cables for working voltage up to and Wrapping Test on street light
281 IS:10810(Part-3)
WIRES including 1100 V conductor
ELECTRICAL- CABLES & Cross Linked Polyethylene Insulated Thermoplastic (A) Tests on Conductor
282 IS 10810(P-1)
WIRES Sheathed Cables for Working Voltage Including 1100 V Annealing Test (For Copper)
ELECTRICAL- CABLES & Cross Linked Polyethylene Insulated Thermoplastic (A)Tests on Conductor
283 IS 10810(P-5)
WIRES Sheathed Cables for Working Voltage Including 1100 V Conductor Resistance Test
ELECTRICAL- CABLES & Cross Linked Polyethylene Insulated Thermoplastic (A)Tests on Conductor Tensile
284 IS 10810(P-2)
WIRES Sheathed Cables for Working Voltage Including 1100 V Test (For Aluminium)
ELECTRICAL- CABLES & Cross Linked Polyethylene Insulated Thermoplastic (A)Tests on Conductor
285 IS 10810(P-3)
WIRES Sheathed Cables for Working Voltage Including 1100 V Wrapping Test (For Aluminium)
(B) (Tests for round steel
ELECTRICAL- CABLES & Cross Linked Polyethylene Insulated Thermoplastic
286 wire/formed steel wire (Strip IS 10810(P-37)
WIRES Sheathed Cables for Working Voltage Including 1100 V
Armour-Elongation at Break
(B) Test for round steel
ELECTRICAL- CABLES & Cross Linked Polyethylene Insulated Thermoplastic wire/formed steel wire (Strip
287 IS:10810(Part-38)
WIRES Sheathed Cables for Working Voltage Including 1100 V armour)- Torsion Test for round
wire
(B) Tests for round steel
Armour)- Resistivity
289 IS 10810(P-40)
WIRES Sheathed Cables for Working Voltage Including 1100 V Armour)- Uniformity of Zinc
Coating
290 IS 10810(P-39)
WIRES Sheathed Cables for Working Voltage Including 1100 V Armour)-Winding Test for
Formed Wire
Armour-Tensile Strength
(B)Tests for round steel
Armour- mass of zinc coating
(B)Tests for round steel
Armour-Dimension
Laboratory Name :

performed used
ELECTRICAL- CABLES & Cross Linked Polyethylene Insulated Thermoplastic (C) Test for thickness of
294 IS 10810(P-6)
WIRES Sheathed Cables for Working Voltage Including 1100 V Insulation
ELECTRICAL- CABLES & Cross Linked Polyethylene Insulated Thermoplastic (C) Test for Thickness of
295 IS:10810(Part-6)
WIRES Sheathed Cables for Working Voltage Including 1100 V Sheath
(D) Physical Test for Insulation-
296 Elongation at Break (After IS:10810(Part-11)
Ageing)
ELECTRICAL- CABLES & Cross Linked Polyethylene Insulated Thermoplastic (D) Physical test for Insulation-
297 IS:10810(Part-30)
WIRES Sheathed Cables for Working Voltage Including 1100 V Hot set Test (Elongation)
(D) Physical test for Insulation-
298 Hot Set Test (Permanent IS:10810(Part-30)
Elongation )
ELECTRICAL- CABLES & Cross Linked Polyethylene Insulated Thermoplastic (D) Physical Test for Insulation-
299 IS 10810(P-7)
WIRES Sheathed Cables for Working Voltage Including 1100 V Tensile Strength
(D) Physical test for Insulation-
300 Tensile Strength Test (After IS:10810(PART-11)
Ageing)
ELECTRICAL- CABLES & Cross Linked Polyethylene Insulated Thermoplastic (D) Physical test for Insulation-
301 IS:10810(Part-33)
WIRES Sheathed Cables for Working Voltage Including 1100 V Water Absorption Test
ELECTRICAL- CABLES & Cross Linked Polyethylene Insulated Thermoplastic (D)Physical Test for Insulation-
302 IS 10810(P-7)
WIRES Sheathed Cables for Working Voltage Including 1100 V Elongation at Break
ELECTRICAL- CABLES & Cross Linked Polyethylene Insulated Thermoplastic (D)Physical Test for Insulation-
303 IS 10810(P-12)
WIRES Sheathed Cables for Working Voltage Including 1100 V Shrinkage Test
(E) Physical Test for Outer
304 Sheath- Loss of mass in Air IS 10810(P-10)
Oven
ELECTRICAL- CABLES & Cross Linked Polyethylene Insulated Thermoplastic (E) Physical Test for Outer
305 10810(P-14)
WIRES Sheathed Cables for Working Voltage Including 1100 V Sheath- Heat Shock Test
306 IS 10810(P-7)
WIRES Sheathed Cables for Working Voltage Including 1100 V Sheath- Tensile Strength Test
307 IS 10810(P-15)
WIRES Sheathed Cables for Working Voltage Including 1100 V Sheath- Hot Deformation Test
308 IS 10810(P-60)
WIRES Sheathed Cables for Working Voltage Including 1100 V Sheath- Thermal Stability Test
309 Sheath- Tensile Strength (After IS 10810(P-11)
Ageing)
310 IS 10810(P-12)
WIRES Sheathed Cables for Working Voltage Including 1100 V Sheath- Shrinkage Test
Laboratory Name :

performed used
311 IS 10810(P-7)
WIRES Sheathed Cables for Working Voltage Including 1100 V Sheath Elongation at Break
312 Sheath Elongation at Break IS 10810(P-11)
(After Ageing)
313 (G) High Voltage Test IS 10810(P-45)
ELECTRICAL- CABLES & Cross Linked Polyethylene Insulated Thermoplastic (G) Insulation Resistance
314 IS: 10810 (PART-43)
WIRES Sheathed Cables for Working Voltage Including 1100 V (Volume Resistivity Test)
ELECTRICAL- CABLES & Cross Linked Polyethylene Insulated Thermoplastic (H) Flammability Test
315 IS: 10810(Part-53)
WIRES Sheathed Cables for Working Voltage Including 1100 V (Unaffected Length)
316 (H)-Flammability Test IS 10810(P-53)
Cold Bend Test (Outer Sheath)
(4.00,6.00,8.04,12.00,14.10,16
.02,18.27,19.98,23.24,25.56,2
317 8.06,30.02,31.96,35.10,40.09, IS 10810(P-20)
45.05,48.03,52.06,54.05,60.03
,70.94,80.02,84.98,90.14,100.
06,109.97 mm)
ELECTRICAL- CABLES & Cross Linked Polyethylene Insulated Thermoplastic Cold Impact Test (Outer
318 IS 10810(P-21)
WIRES Sheathed Cables for Working Voltage Including 1100 V Sheath)
ELECTRICAL- CABLES & Cross Linked Polyethylene Insulated Thermoplastic Flame retardant Test for
319 IS:10810(Part-62)
WIRES Sheathed Cables for Working Voltage Including 1100 V bunched Cable
ELECTRICAL- CABLES & Cross Linked Polyethylene Insulated Thermoplastic Flame Retardant Test for
320 IS:10810(Part-61)
WIRES Sheathed Cables for Working Voltage Including 1100 V Single Cable
321 Oxygen Index Test IS:10810(Part-58)
322 Smoke Density Test IS:10810(Part-63)
323 Temperature Index Test IS:10810(Part-64)
ELECTRICAL- CABLES & Cross Linked Polyethylene Insulated Thermoplastic Test for Halogen Acid Gas
324 IS:10810(Part-59)
WIRES Sheathed Cables for Working Voltage Including 1100 V Evolution
Crosslinked polyethylene insulated cable thermoplastic
ELECTRICAL- CABLES & Elongation at break test for
325 sheathed for working voltage form 3.3 kV upto and IS:10810(Part-11)
WIRES sheath (after ageing)
including 33 kV
ELECTRICAL- CABLES & Flammability Test for PVC
WIRES sheathed cables
including 33 kV
Laboratory Name :

performed used
ELECTRICAL- CABLES &
327 sheathed for working voltage form 3.3 kV upto and Hot deformation test for sheath is:10810(Part-15)
WIRES
including 33 kV
ELECTRICAL- CABLES & Loss of mass in air oven for
WIRES sheath
including 33 kV
329 sheathed for working voltage form 3.3 kV upto and Oxygen index test IS:10810(Part-58)
WIRES
including 33 kV
ELECTRICAL- CABLES & Shrinkage Test for insulation &
WIRES sheath
including 33 kV
ELECTRICAL- CABLES & Thermal Stability test for
WIRES sheath
including 33 kV
332 sheathed for working voltage form 3.3 kV upto and Thickness test for insulation IS:10810(Part-6)
WIRES
including 33 kV
333 sheathed for working voltage form 3.3 kV upto and wrapping test for aluminium IS:10810(Part-3)
WIRES
including 33 kV
334 sheathed for working voltage form 3.3 kV upto and Annealing Test for copper IS:10810(Part-1)
WIRES
including 33 kV
335 sheathed for working voltage form 3.3 kV upto and dimension test for armour IS:10810(Part-36)
WIRES
including 33 kV
ELECTRICAL- CABLES & Elongation at break for
WIRES insulation (after ageing)
including 33 kV
ELECTRICAL- CABLES & Elongation at break for
WIRES insulation (before ageing)
including 33 kV
ELECTRICAL- CABLES & Elongation at break for sheath
WIRES (before ageing)
including 33 kV
ELECTRICAL- CABLES & Elongation at break test for
WIRES armour
including 33 kV
340 sheathed for working voltage form 3.3 kV upto and Heat shock test for sheath IS:10810(Part-14)
WIRES
including 33 kV
Laboratory Name :

performed used
ELECTRICAL- CABLES & Low smoke Halogen acid gas
WIRES evaluation test
including 33 kV
342 sheathed for working voltage form 3.3 kV upto and Mass of zinc coating for armour IS:10810(Part-41)
WIRES
including 33 kV
343 sheathed for working voltage form 3.3 kV upto and Resistivity test for armour IS:10810(Part-42)
WIRES
including 33 kV
344 sheathed for working voltage form 3.3 kV upto and Smoke density test IS:10810(Part-63)
WIRES
including 33 kV
345 sheathed for working voltage form 3.3 kV upto and Temperature index test IS:10810(Part-64)
WIRES
including 33 kV
ELECTRICAL- CABLES & Tensile strength for sheath
WIRES (before ageing)
including 33 kV
ELECTRICAL- CABLES & Tensile strength test for
WIRES armour
including 33 kV
WIRES insulation (after ageing)
including 33 kV
WIRES insulation (before ageing )
including 33 kV
WIRES sheath(After ageing)
including 33 kV
351 sheathed for working voltage form 3.3 kV upto and Tensile test for aluminium IS:10810(Part-2)
WIRES
including 33 kV
352 sheathed for working voltage form 3.3 kV upto and Thickness test for sheath IS:10810(Part-6)
WIRES
including 33 kV
ELECTRICAL- CABLES & Uniformity of zinc coating for
WIRES armour
including 33 kV
ELECTRICAL- CABLES & Flame Retardant Test for
WIRES bunched cable
including 33 kV
Laboratory Name :

performed used
ELECTRICAL- CABLES & Flame retardant test for single
WIRES cable
including 33 kV
ELECTRICAL- CABLES & Flammability Test (Unaffected
WIRES Length)
including 33 kV
357 sheathed for working voltage form 3.3 kV upto and Hot Set Test (Elongation) IS:10810(Part-30)
WIRES
including 33 kV
ELECTRICAL- CABLES & Hot Set Test (Permanent
WIRES Elongation)
including 33 kV
ELECTRICAL- CABLES & Insulation Resistance (Volume
WIRES Resistivity) Test
including 33 kV
360 sheathed for working voltage form 3.3 kV upto and Torsion test for round armour IS:10810(Part-38)
WIRES
including 33 kV
361 sheathed for working voltage form 3.3 kV upto and Water Absorption Test IS:10810(Part-33)
WIRES
including 33 kV
Polyvinyl Chloride insulated unsheathed and sheathed
ELECTRICAL- CABLES & (A) Test on Conductor-
362 cores/ cords with rigid and flexible conductor for rated IS 10810(P-3)
WIRES Wrapping Test (For Aluminium)
voltage up to and including 1100 volts
WIRES Conductor Resistance Test
WIRES Annealing Test (For Copper)
ELECTRICAL- CABLES & (A) Test on Conductor- Tensile
WIRES test (For Aluminium)
Polyvinyl Chloride insulated unsheathed and sheathed (B) Test for Overall Dimension
366 cores/ cords with rigid and flexible conductor for rated & Thickness of Insulation/ IS10810(P-6)
WIRES
voltage up to and including 1100 volts Sheath
Polyvinyl Chloride insulated unsheathed and sheathed (C & D) Physical Test for
367 cores/ cords with rigid and flexible conductor for rated Insulation/Sheath- Tensile IS 10810(P-7)
WIRES
voltage up to and including 1100 volts Strength
368 cores/ cords with rigid and flexible conductor for rated Insulation/Sheath- Cold Impact IS 10810(P-21)
WIRES
voltage up to and including 1100 volts Test
Laboratory Name :

performed used
369 cores/ cords with rigid and flexible conductor for rated Insulation/Sheath- Elongation IS 10810(P-7)
WIRES
voltage up to and including 1100 volts at Break
370 cores/ cords with rigid and flexible conductor for rated Insulation/Sheath- Elongation IS 10810(P-11)
WIRES
voltage up to and including 1100 volts at Break (After Ageing))
371 cores/ cords with rigid and flexible conductor for rated Insulation/Sheath- Heat Shock IS 10810(P-14)
WIRES
372 cores/ cords with rigid and flexible conductor for rated Insulation/Sheath- Hot IS 10810(P-15)
WIRES
voltage up to and including 1100 volts Deformation Test
373 cores/ cords with rigid and flexible conductor for rated Insulation/Sheath- Loss of Mass IS 10810(P-10)
WIRES
374 cores/ cords with rigid and flexible conductor for rated Insulation/Sheath- Shrinkage IS 10810(P-12)
WIRES
375 cores/ cords with rigid and flexible conductor for rated Insulation/Sheath- Thermal IS 10810(P-60)
WIRES
voltage up to and including 1100 volts Stability Test
(C & D) Physical Test for
Insulation/Sheath- Cold Bend
Test
Polyvinyl Chloride insulated unsheathed and sheathed (4.00,6.00,8.04,12.00,14.10,16
376 cores/ cords with rigid and flexible conductor for rated .02,18.27,19.98,23.24,25.56,2 IS 10810(P-20)
WIRES
voltage up to and including 1100 volts 8.06,30.02,31.96,35.10,40.09,
45.05,48.03,52.06,54.05,60.03
,70.94,80.02,84.98,90.14,100.
06,109.97 mm)
377 cores/ cords with rigid and flexible conductor for rated Insulation/Sheath-Tensile IS 10810(P-11)
WIRES
voltage up to and including 1100 volts Strength (After Ageing))
378 cores/ cords with rigid and flexible conductor for rated (C & E) -Flammability Test IS 10810(P-53)
WIRES
ELECTRICAL- CABLES & (E) High Voltage Test (Room
WIRES Temp)
ELECTRICAL- CABLES & (E) High Voltage Test ,AC/DC
WIRES (Water Immersion Test)
Laboratory Name :

performed used
381 cores/ cords with rigid and flexible conductor for rated (E) Insulation Resistance Test IS 10810(P-43)
WIRES
Polyvinyl Chloride insulated unsheathed and sheathed (A) Test on Conductor-
382 cores/ cords with rigid and flexible conductor for rated Persulphate test (For Tinned IS 10810 Part-4
WIRES
voltage up to and including 1100 volts Copper Conductor cable Only)
ELECTRICAL- CABLES & (C & D), Test for Halogen Acid
383 cores/ cords with rigid and flexible conductor for rated IS:10810(Part-59)
WIRES Gas Evaluation
ELECTRICAL- CABLES & (C & E) ,Flammability Test
384 cores/ cords with rigid and flexible conductor for rated IS:10810 (Part-53)
WIRES (unaffected length )
385 cores/ cords with rigid and flexible conductor for rated (C, D), Smoke Density Rating IS:10810(Part-63)
WIRES
386 cores/ cords with rigid and flexible conductor for rated Oxygen Index Test IS:10810(Part-58)
WIRES
ELECTRICAL- CABLES & Physical test on insulation
387 cores/ cords with rigid and flexible conductor for rated IS:10810(Part-43)
WIRES volume resistivity test
388 cores/ cords with rigid and flexible conductor for rated Temperature Index Test IS:10810(Part-64)
WIRES
(B) Test for round steel wire/
ELECTRICAL- CABLES & PVC Insulated (Heavy Duty) Electric Cable Working Voltage
389 formed steel wire (strip) IS 10810 Part-37
WIRES upto and including 1100 V
Armours- Elongation at break
ELECTRICAL- CABLES & PVC Insulated (Heavy Duty) Electric cable Working Voltage (A) Tests on Conductor-
390 IS 10810(P-5)
WIRES upto and including 1100 V Conductor Resistance Test
ELECTRICAL- CABLES & PVC Insulated (Heavy Duty) Electric cable Working Voltage (A) Tests on Conductor Tensile
391 IS 10810(P-2)
WIRES upto and including 1100 V Test (For Aluminiumm)
ELECTRICAL- CABLES & PVC Insulated (Heavy Duty) Electric cable Working Voltage (A) Tests on Conductor
392 IS 10810(P-3)
WIRES upto and including 1100 V Wrapping Test (For Aluminium)
ELECTRICAL- CABLES & PVC Insulated (Heavy Duty) Electric cable Working Voltage (A)Tests on Conductor-
393 IS 10810(P-1)
WIRES upto and including 1100 V Annealing Test (For Copper)
ELECTRICAL- CABLES & PVC Insulated (Heavy Duty) Electric Cable Working Voltage (C)Test for thickness of
394 IS 10810 Part-6
WIRES upto and including 1100 V Insulation
395 (C)Test for thickness of Sheath IS 10810 Part-6
Laboratory Name :

performed used
(D) Physical test for insulation
396 and outer sheath- Thermal IS:10810(Part-60)
stability test
(D) Physical Tests for Insulation
ELECTRICAL- CABLES & PVC Insulated (Heavy Duty) Electric cable Working Voltage
397 and Outer Sheath- Loss of Mass IS 10810(P-10)
in Air Oven
398 and Outer Sheath- Elongation IS 10810(P-11)
at Break (After Ageing)
399 and Outer Sheath- Heat Shock IS 10810(P-14)
Test
400 and Outer Sheath- Hot IS 10810(P-15)
Deformation Test
401 and Outer Sheath- Shrinkage IS:10810(Part-12)
Test
402 and Outer Sheath- Tensile IS 10810(P-7)
Strength
403 and Outer Sheath-Tensile IS 10810(P-11)
Strength (After Ageing))
(D)Physical Tests for Insulation
404 and Outer Sheath- Thermal IS 10810(P-60)
Stability Test
(D)Physical Tests for Insulation
405 and Outer Sheath-Elongation at IS 10810(P-7)
Break
ELECTRICAL- CABLES & PVC Insulated (Heavy Duty) Electric Cable Working Voltage (E) Insulation Resistance
406 IS:10810(Part-43)
WIRES upto and including 1100 V Constant
407 (E)- Insulation Resistance Test IS 10810(P-43)
ELECTRICAL- CABLES & PVC Insulated (Heavy Duty) Electric cable Working Voltage (F)-High Voltage Test (Water
408 IS 10810(P-45)
WIRES upto and including 1100 V Immersion AC/DC Test)
ELECTRICAL- CABLES & PVC Insulated (Heavy Duty) Electric Cable Working Voltage (G) High Voltage Test at Room
409 IS 10810(P-45)
WIRES upto and including 1100 V Temperature
410 (H)-Flammability Test IS 10810(P-53)
Laboratory Name :

performed used
ELECTRICAL- CABLES & PVC Insulated (Heavy Duty) Electric cable Working Voltage (H)-Flammability Test
411 IS:10810(Part-53)
WIRES upto and including 1100 V (Unaffected Length)
B)Test for round steel wire/
Armours- Dimensions test
WIRES upto and Including 1100 V
Armours- Mass of Zinc Coating
ELECTRICAL- CABLES & PVC Insulated (Heavy Duty) Electric Cable Working Voltage formed steel wire (strip)
414 IS 10810 Part-39
WIRES upto and Including 1100 V Armours- Winding test for
formed wires
ELECTRICAL- CABLES & PVC Insulated (Heavy Duty) Electric cable Working Voltage formed steel wire (strip)
415 IS:10810(Part-38)
WIRES upto and including 1100 V Armours-Torsion test for round
armour
416 formed testing steel wire IS 10810 Part-42
WIRES upto and Including 1100 V
(strip) Armours- Resistivity Test
ELECTRICAL- CABLES & PVC Insulated (Heavy Duty) Electric Cable Working Voltage formed testing steel wire
417 IS 10810 Part-40
WIRES upto and Including 1100 V (strip) Armours- Uniformity of
Zinc Coating Test
418 Cold Bed Test IS 10810(P-20)
419 Cold Impact Test IS 10810(P-21)
ELECTRICAL- CABLES & PVC Insulated (Heavy Duty) Electric Cable Working Voltage Flame Retardant Test for
420 IS:10810(Part-61)
WIRES upto and including 1100 V Single Cable
ELECTRICAL- CABLES & PVC Insulated (Heavy Duty) Electric Cable Working Voltage Flame Retardant Test for
421 IS:10810(Part-62)
WIRES upto and including 1100 V bunched cable
ELECTRICAL- CABLES & PVC Insulated (Heavy Duty) Electric Cable Working Voltage Test for Halogen Acid Gas
425 IS:10810(Part-59)
WIRES upto and including 1100 V Evaluation
Laboratory Name :

performed used
426 Volume resistivity Test IS:10810(Part-43)
ELECTRICAL- CABLES & PVC insulated (heavy duty) electric cables for working Elongation at break test for
427 IS:10810(Part-37)
WIRES voltage from 3.3 KV up to and including 11 KV armour
ELECTRICAL- CABLES & PVC insulated (heavy duty) electric cables for working
428 Loss of mass test for insulation IS:10810(Part-15)
WIRES voltage from 3.3 KV up to and including 11 KV
429 Annealing test for copper IS:10810(Part-1)
430 Cold impact test for insulation IS:10810(Part-21)
431 Cold impact test for sheath IS:10810(Part-21)
432 Dimension test for armour IS:10810(Part-36)
ELECTRICAL- CABLES & PVC insulated (heavy duty) electric cables for working Elongation at break for
433 IS:10810(Part -11)
WIRES voltage from 3.3 KV up to and including 11 KV insulation (after ageing)
ELECTRICAL- CABLES & PVC insulated (heavy duty) electric cables for working Elongation at break for sheath
434 IS:10810(Part-11)
WIRES voltage from 3.3 KV up to and including 11 KV (after ageing)
ELECTRICAL- CABLES & PVC insulated (heavy duty) electric cables for working Elongation at break for sheath
435 IS:10810(Part-7)
WIRES voltage from 3.3 KV up to and including 11 KV (Before ageing)
ELECTRICAL- CABLES & PVC insulated (heavy duty) electric cables for working Elongation test for insulation
436 IS:10810(Part-7 )
WIRES voltage from 3.3 KV up to and including 11 KV (before ageing)
ELECTRICAL- CABLES & PVC insulated (heavy duty) electric cables for working Flame Retardant Test for
437 IS:10810(Part-62)
WIRES voltage from 3.3 KV up to and including 11 KV bunched cable
ELECTRICAL- CABLES & PVC insulated (heavy duty) electric cables for working Flame Retardant test for single
438 IS:10810(Part-61)
WIRES voltage from 3.3 KV up to and including 11 KV cable
439 Flammability test IS:10810(Part-53)
ELECTRICAL- CABLES & PVC insulated (heavy duty) electric cables for working Flammability Test (Unaffected
440 IS:10810(Part-53)
WIRES voltage from 3.3 KV up to and including 11 KV Length)
441 Heat shock test for sheath IS:10810(Part-14)
442 Heat shock test for insulation IS:10810(Part-14)
ELECTRICAL- CABLES & PVC insulated (heavy duty) electric cables for working Hot deformation test for
443 IS:10810(Part-15)
WIRES voltage from 3.3 KV up to and including 11 KV insulation
444 Hot deformation test for sheath IS:10810(Part-15)
Laboratory Name :

performed used
445 Insulation resistance constant IS:10810(Part-43)
446 Loss of mass test for sheath IS:10810(Part-10)
ELECTRICAL- CABLES & PVC insulated (heavy duty) electric cables for working Mass of zinc coating test for
447 IS:10810(Part-41)
449 Resistivity test for armour IS:10810(Part- 42)
450 Shrinkage Test for insulation IS:10810(Part-12)
451 Shrinkage test for sheath IS:10810(Part-12)
ELECTRICAL- CABLES & PVC insulated (heavy duty) electric cables for working Tensile strength test for
454 IS:10810(Part-2)
WIRES voltage from 3.3 KV up to and including 11 KV aluminium
ELECTRICAL- CABLES & PVC insulated (heavy duty) electric cables for working Tensile strength for insulation
455 IS:10810(Part-11)
WIRES voltage from 3.3 KV up to and including 11 KV (after ageing )
ELECTRICAL- CABLES & PVC insulated (heavy duty) electric cables for working Tensile strength test for sheath
456 IS:10810(Part-11)
WIRES voltage from 3.3 KV up to and including 11 KV (after ageing)
457 IS:10810(Part-37)
458 IS:10810(Part- 7)
WIRES voltage from 3.3 KV up to and including 11 KV insulation (before ageing)
ELECTRICAL- CABLES & PVC insulated (heavy duty) electric cables for working Tensile strength test for sheath
459 IS:10810(Part-7)
WIRES voltage from 3.3 KV up to and including 11 KV (before ageing )
ELECTRICAL- CABLES & PVC insulated (heavy duty) electric cables for working Test for Halogen acid gas
460 IS:10810(Part-59)
WIRES voltage from 3.3 KV up to and including 11 KV evaluation
ELECTRICAL- CABLES & PVC insulated (heavy duty) electric cables for working Thermal stability test for
461 IS:10810(Part-60)
WIRES voltage from 3.3 KV up to and including 11 KV insulation
ELECTRICAL- CABLES & PVC insulated (heavy duty) electric cables for working Thermal stability test for
462 IS:10810(Part-60)
WIRES voltage from 3.3 KV up to and including 11 KV sheath
463 Thickness test for insulation IS:10810(Part-6)
Laboratory Name :

performed used
464 Thickness test for sheath IS:10810(Part-6 )
465 Torsion test for round armour IS:10810(Part-38)
ELECTRICAL- CABLES & PVC insulated (heavy duty) electric cables for working Uniformity of zinc coating for
466 IS:10810(Part-40)
467 Volume Resistivity Test IS:10810(Part-43)
468 Water Absorption Test IS:10810(Part-33)
469 Winding test for formed wire IS 10810 Part-39
470 Wrapping test for aluminium IS:10810(Part-3)
(B)Test for round steel wire/
ELECTRICAL- CABLES & PVC Insulated Cables (Heavy Duty) Electric Cable Working
WIRES Voltage upto and Including 1100 V
Armours-Tensile Strength Test
Thermosetting insulated fire survival cables for fixed
ELECTRICAL- CABLES & installation having low emission of smoke and corrosive Elongation at break for
472 IS:10810(Part-7)
WIRES gases when affected by fire for working voltage up to and insulation( before ageing)
including 1100 V AC and 1500 V DC
Cold bend test for sheath
(4.00,6.00,8.04,12.00,14.10,16
.02,18.27,19.98,23.24,25.56,2
ELECTRICAL- CABLES & installation having low emission of smoke and corrosive
473 8.06,30.02,31.96,35.10,40.09, IS:10810(Part-20)
WIRES gases when affected by fire for working voltage up to and
45.05,48.03,52.06,54.05,60.03
,70.94,80.02,84.98,90.14,100.
06,109.97 mm)
474 Annealing test for copper IS:10810(Part-2)
ELECTRICAL- CABLES & installation having low emission of smoke and corrosive Assessment of Halogen test
475 IS:10810(Part-59)
WIRES gases when affected by fire for working voltage up to and (HCl)
ELECTRICAL- CABLES & installation having low emission of smoke and corrosive Cold impact test for sheath and
476 IS:10810(Part-21)
WIRES gases when affected by fire for working voltage up to and insulation
Laboratory Name :

performed used
477 Conductor Resistance Test IS:10810(Part-5)
478 Dimension Test for armour IS:10810(Part-36)
ELECTRICAL- CABLES & installation having low emission of smoke and corrosive Elongation at break for
479 IS:10810(Part-11)
WIRES gases when affected by fire for working voltage up to and insulation (after ageing)
ELECTRICAL- CABLES & installation having low emission of smoke and corrosive Elongation at break for sheath
480 IS:10810(Part-11)
WIRES gases when affected by fire for working voltage up to and (After ageing)
ELECTRICAL- CABLES & installation having low emission of smoke and corrosive Elongation at break for sheath
481 IS:10810(Part-7)
WIRES gases when affected by fire for working voltage up to and (before ageing)
482 Elongation test for armour IS:10810(Part-37)
ELECTRICAL- CABLES & installation having low emission of smoke and corrosive Flammability Test (flame on
483 IS:10810(Part-61)
WIRES gases when affected by fire for working voltage up to and Single cable)
ELECTRICAL- CABLES & installation having low emission of smoke and corrosive Flammability test (Flame test
484 IS 10810 part-62
WIRES gases when affected by fire for working voltage up to and on bunched cable)
485 Heat shock test IS:10810(Part- 14)
ELECTRICAL- CABLES & installation having low emission of smoke and corrosive Hot Set Test ( Permanent
486 IS:10810(Part-30)
WIRES gases when affected by fire for working voltage up to and Elongation)
487 Hot set Test (Elongation ) IS:10810(Part-30)
Laboratory Name :

performed used
488 Insulation Resistance test IS:10810(Part-43)
ELECTRICAL- CABLES & installation having low emission of smoke and corrosive Mass of Zinc coating for
489 IS:10810(Part-41)
WIRES gases when affected by fire for working voltage up to and armour
ELECTRICAL- CABLES & installation having low emission of smoke and corrosive Persulphate test for tinned
491 IS:10810(Part-4 )
WIRES gases when affected by fire for working voltage up to and copper
492 Resistivity test for armour IS:10810(Part-42)
493 Shrinkage Test for Insulation IS:10810(Part-12)
ELECTRICAL- CABLES & installation having low emission of smoke and corrosive Tensile Strength for sheath
496 IS:10810(Part-11)
WIRES gases when affected by fire for working voltage up to and (after ageing)
ELECTRICAL- CABLES & installation having low emission of smoke and corrosive Tensile Strength for sheath
497 IS:10810(Part-7)
WIRES gases when affected by fire for working voltage up to and (before ageing)
ELECTRICAL- CABLES & installation having low emission of smoke and corrosive Tensile Strength test for
498 IS:10810(Part- 37)
WIRES gases when affected by fire for working voltage up to and armour
Laboratory Name :

performed used
499 IS:10810(Part -11)
WIRES gases when affected by fire for working voltage up to and insulation (after ageing)
500 IS:10810(Part -7)
WIRES gases when affected by fire for working voltage up to and insulation (before ageing)
501 Thickness test for insulation IS: 10810(Part-6)
502 Thickness test for sheath IS:10810(Part-6)
503 Torsion test for armour IS:10810(Part-38)
504 Uniformity of zinc coating IS 10810 Part-42
505 Water Absorption Test IS:10810(Part-33)
TThermosetting insulated fire survival cables for fixed
506 High voltage test IS:10810(Part-45)
ELECTRICAL- WIRING Enclosures for accessories for household and similar fixed
507 Marking IS 14772
ACCESSORIES installation
508 Mechanical Strength IS 14772
ELECTRICAL- WIRING Enclosures for accessories for household and similar fixed Protection against electric
509 IS 14772
ACCESSORIES installation shock
510 Resistance to heat IS 14772
511 Resistance to rusting IS:14772
Laboratory Name :

performed used
Additional Test on Pins
Plugs and Socket-Outlets for Household and Similar
ELECTRICAL- WIRING Provided with Insulating
512 Purposes of Rated Voltage up to and Including 250 V and IS 1293
ACCESSORIES Sleeves (Impact test at Low
Rated Current up to and Including 16 A
Temp.)
ELECTRICAL- WIRING
513 Purposes of Rated Voltage up to and Including 250 V and Compression Test IS 1293
ACCESSORIES
ELECTRICAL- WIRING Construction of Plug and
ACCESSORIES Potable Socket Outlet
ELECTRICAL- WIRING Construction Requirement of
ACCESSORIES Fixed Socket Outlet
ELECTRICAL- WIRING Creepage Distance and
ACCESSORIES Clearance Distance
ELECTRICAL- WIRING
517 Purposes of Rated Voltage up to and Including 250 V and Dimensions IS 1293
ACCESSORIES
ELECTRICAL- WIRING Electric Strength ( After
ACCESSORIES Humidity)
ELECTRICAL- WIRING Flexible Cables and Their
ACCESSORIES Connection
ELECTRICAL- WIRING Force Necessary Withdraw the
ACCESSORIES Plug
ELECTRICAL- WIRING Insulation Resistance (After
521 Purposes of Rated Voltage up to and Including 250 V and IS:1293
ACCESSORIES Humidity)
ELECTRICAL- WIRING
522 Purposes of Rated Voltage up to and Including 250 V and Making and Breaking Capacity IS 1293
ACCESSORIES
ELECTRICAL- WIRING
523 Purposes of Rated Voltage up to and Including 250 V and Marking IS 1293
ACCESSORIES
ELECTRICAL- WIRING
524 Purposes of Rated Voltage up to and Including 250 V and Mechanical Strength IS 1293
ACCESSORIES
Laboratory Name :

performed used
ELECTRICAL- WIRING
525 Purposes of Rated Voltage up to and Including 250 V and Normal Operation IS1293
ACCESSORIES
ELECTRICAL- WIRING
526 Purposes of Rated Voltage up to and Including 250 V and Operation of Earthing Contact IS 1293
ACCESSORIES
ELECTRICAL- WIRING Protection Against Electric
ACCESSORIES Shock
ELECTRICAL- WIRING
528 Purposes of Rated Voltage up to and Including 250 V and Provision of Earthing IS 1293
ACCESSORIES
ELECTRICAL- WIRING
529 Purposes of Rated Voltage up to and Including 250 V and Resistance to Ageing IS 1293
ACCESSORIES
ELECTRICAL- WIRING
530 Purposes of Rated Voltage up to and Including 250 V and Resistance to Heat IS 1293
ACCESSORIES
ELECTRICAL- WIRING
531 Purposes of Rated Voltage up to and Including 250 V and Resistance to Humidity IS 1293
ACCESSORIES
ELECTRICAL- WIRING
532 Purposes of Rated Voltage up to and Including 250 V and Resistance to Rusting IS 1293
ACCESSORIES
ELECTRICAL- WIRING Screw Current Carrying Parts
ACCESSORIES and Connection
ELECTRICAL- WIRING
534 Purposes of Rated Voltage up to and Including 250 V and Temperature Rise Test IS :1293
ACCESSORIES
ELECTRICAL- WIRING
535 Purposes of Rated Voltage up to and Including 250 V and Terminals IS 1293
ACCESSORIES
ELECTRICAL- WIRING
536 Rigid Plain Conduits of Insulating Material Bending Test IS:9537(Part-3)
ACCESSORIES
ELECTRICAL- WIRING
537 Rigid Plain Conduits of Insulating Material Collapse Test IS:9537(Part-1)
ACCESSORIES
ELECTRICAL- WIRING
538 Rigid Plain Conduits of Insulating Material Compression Test IS 9537(P-1)
ACCESSORIES
ELECTRICAL- WIRING
539 Rigid Plain Conduits of Insulating Material Dimnesions IS 9537(P-3)
ACCESSORIES
Laboratory Name :

performed used
ELECTRICAL- WIRING
540 Rigid Plain Conduits of Insulating Material Electrical Strength IS 9537(P-1)
ACCESSORIES
ELECTRICAL- WIRING
541 Rigid Plain Conduits of Insulating Material Impact Test IS 9537(P-1)
ACCESSORIES
ELECTRICAL- WIRING
542 Rigid Plain Conduits of Insulating Material Insulation Resistance IS 9537(Part-1)
ACCESSORIES
ELECTRICAL- WIRING
543 Rigid Plain Conduits of Insulating Material Resistance to Burning IS 9537(P-1)
ACCESSORIES
ELECTRICAL- WIRING
544 Rigid Plain Conduits of Insulating Material Resistance to Heat Test IS 9537(P-3)
ACCESSORIES
ELECTRICAL- WIRING
545 Rigid Plain Conduits of Insulating Material Uniformity of Wall Thickness IS 9537(P-1)
ACCESSORIES
ELECTRICAL- WIRING
546 Rigid steel conduit for electrical installation Construction IS:9537(Part-2)
ACCESSORIES
ELECTRICAL- WIRING
547 Rigid steel conduit for electrical installation External influences IS:9537(Part-2)
ACCESSORIES
ELECTRICAL- WIRING
548 Rigid steel conduit for electrical installation Bending Test IS:9537(Part-2)
ACCESSORIES
ELECTRICAL- WIRING
549 Rigid steel conduit for electrical installation Compression Test IS:9537(Part-2)
ACCESSORIES
ELECTRICAL- WIRING
550 Rigid steel conduit for electrical installation Dimension test IS:9537(Part-2)
ACCESSORIES
ELECTRICAL- WIRING
551 Rigid steel conduit for electrical installation Marking IS:9537(Part-2)
ACCESSORIES
ELECTRICAL- WIRING
552 Rigid steel conduit for electrical installation Thickness test IS:9537(Part-2)
ACCESSORIES
ELECTRICAL- WIRING
553 Specification for fitting for rigid non metallic conduits Checking of Dimension IS:3419
ACCESSORIES
ELECTRICAL- WIRING
554 Specification for fitting for rigid non metallic conduits Copper Test IS:3419
ACCESSORIES
ELECTRICAL- WIRING
555 Specification for fitting for rigid non metallic conduits Impact Resistance Test IS:3419
ACCESSORIES
ELECTRICAL- WIRING
556 Specification for fitting for rigid non metallic conduits Moisture Absorption Test IS:3419
ACCESSORIES
ELECTRICAL- WIRING
557 Specification for fitting for rigid non metallic conduits Resistance to Burning IS:3419
ACCESSORIES
ELECTRICAL- WIRING
558 Specification for fitting for rigid non metallic conduits Resistance to heat IS: 3419
ACCESSORIES
Laboratory Name :

performed used
ELECTRICAL- WIRING Test for electrical
559 Specification for fitting for rigid non metallic conduits IS:3419
ACCESSORIES characteristics
ELECTRICAL- WIRING Test for resistance to chemical
560 Specification for fitting for rigid non metallic conduits IS:3419
ACCESSORIES action
ELECTRICAL- WIRING
561 Specification for fitting for rigid non metallic conduits Test for resistance to oil IS:3419
ACCESSORIES
ELECTRICAL- WIRING
562 Specification for fitting for rigid non metallic conduits Visual Examination IS: 3419
ACCESSORIES
ELECTRICAL- WIRING Creepage Distance and
563 Switches for Domestic & Similar Purpose IS 3854
ACCESSORIES Clearance Distance
ELECTRICAL- WIRING
564 Switches for Domestic & Similar Purpose Electric Strength Test IS 3854
ACCESSORIES
ELECTRICAL- WIRING
565 Switches for Domestic & Similar Purpose Insulation Resistance Test IS 3854
ACCESSORIES
ELECTRICAL- WIRING
566 Switches for Domestic & Similar Purpose Making and Breaking Capacity IS 3854
ACCESSORIES
ELECTRICAL- WIRING
567 Switches for Domestic & Similar Purpose Marking IS 3854
ACCESSORIES
ELECTRICAL- WIRING
568 Switches for Domestic & Similar Purpose Mechanical Strength Test IS 3854
ACCESSORIES
ELECTRICAL- WIRING
569 Switches for Domestic & Similar Purpose Normal Operation IS 3854
ACCESSORIES
ELECTRICAL- WIRING Protection Against Electric
ACCESSORIES Shock
ELECTRICAL- WIRING
571 Switches for Domestic & Similar Purpose Provision of Earthing IS 3854
ACCESSORIES
ELECTRICAL- WIRING Resistance to Ageing &
ACCESSORIES Moisture
ELECTRICAL- WIRING
573 Switches for Domestic & Similar Purpose Resistance to Heat IS 3854
ACCESSORIES
ELECTRICAL- WIRING
574 Switches for Domestic & Similar Purpose Resistance to Rusting IS 3854
ACCESSORIES
ELECTRICAL- WIRING
575 Switches for Domestic & Similar Purpose Temperature Rise IS 3854
ACCESSORIES
ELECTRICAL- WIRING
576 Switches for Domestic & Similar Purpose Terminal and Screws IS 3854
ACCESSORIES
MECHANICAL- BUILDINGS
577 AAC Block Block Density IS 6441 (P-1)
MATERIALS
Laboratory Name :

performed used
578 AAC Block Compressive Strength IS 6441(P-5)
MATERIALS
579 AAC Block Dimension-Height IS 2185 (P-3)
MATERIALS
580 AAC Block Dimension-Length IS 2185 (P-3)
MATERIALS
581 AAC Block Dimension-Width IS 2185 (P-3)
MATERIALS
582 AAC Block Drying Shrinkage IS 6441(P-2)
MATERIALS
583 AAC Block Thermal Conductivity IS:3346
MATERIALS
584 AAC Block Adhesive Bulk Density IS 2386(P-3)
MATERIALS
585 AAC Block Adhesive Compressive Strength 28 Days IS:2250
MATERIALS
MATERIALS
MATERIALS
588 AAC Block Adhesive Open Time IS 15477
MATERIALS
589 AAC Block Adhesive Split Tensile Strength ASTM C-1660
MATERIALS
590 Bitumen Absolute Viscosity IS:1206(Part-2)
MATERIALS
591 Bitumen Kinemetic Viscosity IS:1206(Part-3)
MATERIALS
592 Bitumen Emulsion Bitumen Content IS:3117 (Annex-B)
MATERIALS
593 Bitumen Emulsion Coagulation of Emulsion IS:8887 (Annex-C)
MATERIALS
594 Bitumen Emulsion Ductility at 27 Degree IS:1208
MATERIALS
595 Bitumen Emulsion Particle Charge IS:8887 (Annex-E)
MATERIALS
596 Bitumen Emulsion Penetration at 25 degree IS:1203
MATERIALS
Laboratory Name :

performed used
597 Bitumen Emulsion Residue by Evaporation IS:8887 (Annex-J)
MATERIALS
598 Bitumen Emulsion Residue on 600 micron IS Sieve IS:8887 (Annex-B)
MATERIALS
599 Bitumen Emulsion Say bolt Viscosity IS:3117 (Annex-A)
MATERIALS
600 Bitumen Emulsion Solubility in trichloroethylene IS:1216
MATERIALS
MECHANICAL- BUILDINGS Storage Stability (After 24
601 Bitumen Emulsion IS:8887 (Annex-D)
MATERIALS hours)
602 Bitumen Emulsion Water Content IS:1211
MATERIALS
603 Bituminous Concrete Bitumen Content ASTM D-2172
MATERIALS
604 Bituminous Concrete Bulk Specific Gravity ASTM D-2726
MATERIALS
605 Bituminous Concrete Gradation (45~0.075 mm) IS:2386 (P-1)
MATERIALS
606 Bituminous Concrete Marshall Flow AASHTO T245
MATERIALS
607 Bituminous Concrete Marshall Stability AASHTO T245
MATERIALS
608 Bituminous Concrete Stripping Value IS:6241
MATERIALS
609 Bituminous Mix Bitumen Content ASTM D-2172
MATERIALS
610 Burnt Clay Fly Ash Building Brick Compressive Strength IS:3495(Part-1)
MATERIALS
611 Burnt Clay Fly Ash Building Brick Dimension (Height ) IS:13757
MATERIALS
612 Burnt Clay Fly Ash Building Brick Dimension (Length) IS:13757
MATERIALS
613 Burnt Clay Fly Ash Building Brick Dimension (Width ) IS:13757
MATERIALS
614 Burnt Clay Fly Ash Building Brick Water Absorption IS:3495(Part-2)
MATERIALS
615 Ceramic Tiles / Vitrified Tiles Resistance to household IS 13630(P-8)
MATERIALS
Laboratory Name :

performed used
616 Ceramic Tiles / Vitrified Tiles Breaking Strength IS 13630(P-6)
MATERIALS
617 Ceramic Tiles / Vitrified Tiles Bulk Density IS 13630 (P-2)
MATERIALS
MECHANICAL- BUILDINGS Co- efficient of linear thermal
618 Ceramic Tiles / Vitrified Tiles IS:13630 (Part-4)
MATERIALS expansion
619 Ceramic Tiles / Vitrified Tiles Crazing Resistance IS:13630 (Part- 9)
MATERIALS
620 Ceramic Tiles / Vitrified Tiles Dimension- Length IS 13630(P-1)
MATERIALS
621 Ceramic Tiles / Vitrified Tiles Dimension- Thickness IS 13630(P-1)
MATERIALS
622 Ceramic Tiles / Vitrified Tiles Dimension- Width IS 13630(P-1)
MATERIALS
623 Ceramic Tiles / Vitrified Tiles Frost Resistance IS:13630(Part-10)
MATERIALS
624 Ceramic Tiles / Vitrified Tiles Hardness by Moh's Scale IS 13630 (P-13)
MATERIALS
625 Ceramic Tiles / Vitrified Tiles Impact Resistance IS:13630(Part -14)
MATERIALS
626 Ceramic Tiles / Vitrified Tiles Modulus of rupture IS 13630(P-6)
MATERIALS
627 Ceramic Tiles / Vitrified Tiles Moisture Extension IS:13630 (Part-3 )
MATERIALS
628 Ceramic Tiles / Vitrified Tiles Rectangularity IS 13630(P-1)
MATERIALS
629 Ceramic Tiles / Vitrified Tiles Resistance to alkaline IS 13630(P-8)
MATERIALS
630 Ceramic Tiles / Vitrified Tiles Resistance to deep abrasion IS:13630 (Part-12)
MATERIALS
631 Ceramic Tiles / Vitrified Tiles Resistance to staining IS 13630(P-8)
MATERIALS
632 Ceramic Tiles / Vitrified Tiles Resistance to surface abrasion IS:13630(Part-11)
MATERIALS
633 Ceramic Tiles / Vitrified Tiles Straightness IS 13630(P-1)
MATERIALS
MECHANICAL- BUILDINGS Surface Flatness Centre
634 Ceramic Tiles / Vitrified Tiles IS 13630(P-1)
MATERIALS Curvature
Laboratory Name :

performed used
MECHANICAL- BUILDINGS Surface Flatness Edge
635 Ceramic Tiles / Vitrified Tiles IS 13630(P-1)
MATERIALS Curvature
636 Ceramic Tiles / Vitrified Tiles Surface Flatness Warpage IS 13630(P-1)
MATERIALS
637 Ceramic Tiles / Vitrified Tiles Surface Quality IS:13630(Part-1)
MATERIALS
638 Ceramic Tiles / Vitrified Tiles Thermal Shock Resistance IS:IS:13630 (Part-5 )
MATERIALS
639 Ceramic Tiles / Vitrified Tiles Water Absorption IS 13630 (P-2)
MATERIALS
640 Coarse Aggregate 10 % Fine Value IS 2386 (P-4)
MATERIALS
641 Coarse Aggregate Bulk Density IS 2386 (P-3)
MATERIALS
642 Coarse Aggregate Crushing Value IS 2386 (P-4)
MATERIALS
MECHANICAL- BUILDINGS Deleterious Material (Clay
643 Coarse Aggregate IS 2386 (P-2)
MATERIALS Lumps)
MECHANICAL- BUILDINGS Deleterious Material (Coal &
MATERIALS Lignite)
MECHANICAL- BUILDINGS Deleterious Material (Material
MATERIALS Finer Than 75 Micron IS Sieve)
646 Coarse Aggregate Elongation Index IS 2386 (P-1)
MATERIALS
647 Coarse Aggregate Flakiness Index IS 2386 (P-1)
MATERIALS
648 Coarse Aggregate Impact Value IS 2386 (P-4)
MATERIALS
649 Coarse Aggregate Los Angeles Abrasion Value IS 2386 (P-4)
MATERIALS
650 Coarse Aggregate Petrography IS:2386(Part-8)
MATERIALS
651 Coarse Aggregate Sieve Analysis (80 ~ 2.36 mm) IS 2386 (P-1)
MATERIALS
652 Coarse Aggregate Soundness Test IS 2386 (P-5)
MATERIALS
653 Coarse Aggregate Specific Gravity IS 2386 (P-3)
MATERIALS
Laboratory Name :

performed used
654 Coarse Aggregate Water Absorption IS 2386 (P-3)
MATERIALS
655 Common Burnt Clay Building Bricks Compressive Strength IS:3495(Part-1)
MATERIALS
656 Common Burnt Clay Building Bricks Dimension (Height) IS:1077
MATERIALS
657 Common Burnt Clay Building Bricks Dimension (Length) IS:1077
MATERIALS
658 Common Burnt Clay Building Bricks Dimension (Width) IS:1077
MATERIALS
659 Common Burnt Clay Building Bricks Water Absorption IS:3495(Part-2)
MATERIALS
660 Composite Cement Compressive strength IS 4031(Part-6)
MATERIALS
661 Composite Cement Consistency IS 4031(P-4)
MATERIALS
662 Composite Cement Density IS 4031(P-11)
MATERIALS
663 Composite Cement Drying shrinkage IS 4031(P-10)
MATERIALS
MECHANICAL- BUILDINGS Fineness by Blaine's air
664 Composite Cement IS 4031(P-2)
MATERIALS permeability
665 Composite Cement Setting time (Initial) IS 4031(P-5)
MATERIALS
666 Composite Cement Setting time (Final) IS 4031(P-5)
MATERIALS
MECHANICAL- BUILDINGS Soundness(by autoclave test
MATERIALS method)
MECHANICAL- BUILDINGS Soundness(by lechatelier
MATERIALS method)
669 Concrete (Hardened) Compressive Strength IS:516(Part-1/Sec-1)
MATERIALS
670 Concrete (Hardened) Compressive Strength (ACT) IS:9013
MATERIALS
671 Concrete (Hardened) Flexural Strength IS:516(Part-1/Sec-1)
MATERIALS
672 Concrete (Hardened) Moisture Movement IS:516 (Part-6)
MATERIALS
Laboratory Name :

performed used
673 Concrete (Hardened) RCPT Test ASTM C1202
MATERIALS
674 Concrete (Hardened) Split Tensile Strength IS:516(Part-1/Sec-1)
MATERIALS
675 Concrete (Hardened) Water Permeability DIN 1048(Part-5)
MATERIALS
676 Concrete Admixture Air Content IS:1199(Part-4)
MATERIALS
677 Concrete Admixture Bleeding IS:9103(Annex-D)
MATERIALS
MECHANICAL- BUILDINGS Compressive Strength, Percent
678 Concrete Admixture IS:516(Part-1/Sec-1)
MATERIALS of Control Sample
MECHANICAL- BUILDINGS Flexural Strength, percent of
679 Concrete Admixture IS:516(Part-1/Sec-1)
MATERIALS control sample
680 Concrete Admixture Loss on work ability IS:1199(Part-2)
MATERIALS
681 Concrete Admixture Setting Time (Final) IS:1199(Part-7)
MATERIALS
682 Concrete Admixture Setting Time (Initial) IS:1199(Part-7)
MATERIALS
683 Concrete Admixture Slump IS:1199(Part-2)
MATERIALS
684 Concrete Admixture Water Content IS:9103 (Annex-D)
MATERIALS
685 Concrete Fresh Setting Time (Initial) IS:1199(Part-7)
MATERIALS
686 Concrete Fresh Air Content IS:1199(Part-4)
MATERIALS
687 Concrete Fresh Setting Time (Final ) IS:1199(Part-7)
MATERIALS
688 Concrete Fresh Slump IS:1199(Part-2)
MATERIALS
689 Concrete Hardened (Core) Compressive Strength IS:516(Part-4)
MATERIALS
690 Concrete Hollow/Solid Block Compressive Strength IS 2185 (P-1) (Annex-D)
MATERIALS
691 Concrete Hollow/Solid Block Density IS 2185 (P-1) (Annex-C)
MATERIALS
Laboratory Name :

performed used
692 Concrete Hollow/Solid Block Dimension-Face Cell Thickness IS 2185(P-1) ,Annex-B
MATERIALS
693 Concrete Hollow/Solid Block Dimension-Height IS 2185(P-1)(Annex-C)
MATERIALS
694 Concrete Hollow/Solid Block Dimension-Length IS 2185(P-1)(Annex-C)
MATERIALS
695 Concrete Hollow/Solid Block Dimension-Web thickness IS 2185(P-1),Annex-C
MATERIALS
696 Concrete Hollow/Solid Block Dimension-Width IS 2185(P-1),Annex-C
MATERIALS
697 Concrete Hollow/Solid Block Water Absorption IS 2185 (P-1) ,Annex-E
MATERIALS
698 Concrete Manhole Cover and Frame Dimension (Diameter) IS:12592
MATERIALS
699 Concrete Manhole Cover and Frame Dimension (Thickness) IS: 12592
MATERIALS
700 Concrete Manhole Cover and Frame Dimension of frame (B) IS:12592, Annex-B
MATERIALS
701 Concrete Manhole Cover and Frame Dimension of frame (C) IS:12592, Annex-B
MATERIALS
MECHANICAL- BUILDINGS Dimension of frame (Clear
702 Concrete Manhole Cover and Frame IS:12592, Annex-B
MATERIALS opening in frame A)
703 Concrete Manhole Cover and Frame Dimension of frame (D) IS:12592, Annex-B
MATERIALS
704 Concrete Manhole Cover and Frame Dimension of Frame (E) IS:12592, Annex-B
MATERIALS
MECHANICAL- BUILDINGS Level of the top surface of the
705 Concrete Manhole Cover and Frame IS:12592, Annex-B
MATERIALS frame and cover
706 Concrete Manhole Cover and Frame Lifting Hook IS:12592, Annex-B
MATERIALS
707 Concrete Manhole Cover and Frame Load Test IS:12592, Annex-C
MATERIALS
Maximum clearance at top
708 Concrete Manhole Cover and Frame between the frame and the IS:12592, Annex-B
MATERIALS
cover all round the periphery
709 Concrete Manhole Cover and Frame Permanent Set IS:12592, Annex-C
MATERIALS
Laboratory Name :

performed used
710 Concrete(Hardened) Density IS:516(Part-2) Sec-1
MATERIALS
711 Concrete(Hardened) Dry Shrinkage IS:516 (Part-6)
MATERIALS
712 Concrete(Hardened) Initial Surface Absorption Test IS:516(Part-2) Sec -2
MATERIALS
713 Concrete(Hardened) Modulus of Elasticity IS:516(Part-8) Sec-1
MATERIALS
714 Concrete(Hardened) Water Absorption BS 1881(Part-122)
MATERIALS
715 Concrete(Hardened) Water Permeability IS:516(Part-2) Sec-1
MATERIALS
716 Curing Compound VOC Content ASTM D-3960
MATERIALS
717 Curing Compound Drying Time ASTM C -309
MATERIALS
718 Curing Compound Non- Volatile Content ASTM D -2369
MATERIALS
719 Curing Compound Water Retention ASTM C-309
MATERIALS
720 Dense Bituminous Macadam Bitumen Content ASTM D-2172
MATERIALS
721 Dense Bituminous Macadam Bulk Density ASTM D-2726
MATERIALS
722 Dense Bituminous Macadam Gradation (45~0.075 mm) IS:2386 (P-1)
MATERIALS
723 Dense Bituminous Macadam Marshall Flow AASHTO T245
MATERIALS
724 Dense Bituminous Macadam Marshall Stability AASHTO T245
MATERIALS
725 Dense Bituminous Macadam Stripping Value IS:6241
MATERIALS
726 Fine Aggregate Bulk Density IS 2386 (P-3)
MATERIALS
727 Fine Aggregate Bulking Of Sand IS 2386 (P-3)
MATERIALS
MECHANICAL- BUILDINGS Deleterious Material (Clay
728 Fine Aggregate IS 2386 (P-2)
MATERIALS Lumps)
Laboratory Name :

performed used
MECHANICAL- BUILDINGS Deleterious Material (Coal And
MATERIALS Lignite)
MECHANICAL- BUILDINGS Deleterious Material (Material
MATERIALS Finer Than 75 micron IS Sieve)
731 Fine Aggregate Organic Impurities IS 2386 (P-2)
MATERIALS
732 Fine Aggregate Petrography IS:2386(Part-8)
MATERIALS
733 Fine Aggregate Sieve Analysis (10 ~ 0.15 mm) IS 2386(P-1)
MATERIALS
734 Fine Aggregate Soundness Test IS 2386 (P-5)
MATERIALS
735 Fine Aggregate Specific Gravity IS 2386 (P-3)
MATERIALS
736 Fine Aggregate Water Absorption IS 2386 (P-3)
MATERIALS
737 Fly ash Compressive strength IS 1727
MATERIALS
738 Fly ash Fineness IS 1727
MATERIALS
739 Fly ash Lime reactivity IS 1727
MATERIALS
MECHANICAL- BUILDINGS Particle retained on 45 µ
740 Fly ash IS 1727
MATERIALS sieve(wet sieving)
741 Fly ash Soundness(by autoclave) IS 1727
MATERIALS
MECHANICAL- BUILDINGS Glass Fibre Reinforced Plastic (GRP) Panel Type Door
742 Dimension -Height IS:4020(Part-2)
MATERIALS Shutter
743 Dimension- Thickness IS:4020(Part-2)
MATERIALS Shutter
744 Dimension- Width IS:4020(Part-2)
MATERIALS Shutter
745 Fiber Glass Content IS:14856, Annex-B
MATERIALS Shutter
746 Fire Retardancy IS:14856, Annex-H
MATERIALS Shutter
747 General Flatness IS:4020(Part-3)
MATERIALS Shutter
Laboratory Name :

performed used
748 Impact Indentation Test IS:4020(Part-5)
MATERIALS Shutter
749 Local Planeness IS:4020(Part-4)
MATERIALS Shutter
750 Shock Resistance Test IS:4020(Part-8)
MATERIALS Shutter
751 Tensile Strength IS:14856, Annex-D
MATERIALS Shutter
752 Water Absorption IS:14856, Annex-G
MATERIALS Shutter
753 Local Planeness IS:4020(Part-4)
MATERIALS Shutter
754 GROUT/GP-2 Compressive Strength IS:2250, Annex-A
MATERIALS
755 GROUT/GP-2 Setting Time (Final) IS 4031(P-5)
MATERIALS
756 GROUT/GP-2 Setting Time (Initial) IS 4031(P-5)
MATERIALS
757 GSB/WMM/WBM California bearing ratio(CBR) IS 2720(P-16)
MATERIALS
758 GSB/WMM/WBM Elongation Index IS:2386(Part-1)
MATERIALS
759 GSB/WMM/WBM Flakiness Index IS 2386(P-1)
MATERIALS
760 GSB/WMM/WBM Impact value IS 2386(P-4)
MATERIALS
761 GSB/WMM/WBM Liquid limit IS 2720(P-5)
MATERIALS
762 GSB/WMM/WBM Los angles abrasion value IS 2386(P-4)
MATERIALS
763 GSB/WMM/WBM Plastic limit IS 2720(P-5)
MATERIALS
MECHANICAL- BUILDINGS Sieve analysis (75 ~ 0.075
764 GSB/WMM/WBM IS 2386(P-1)
MATERIALS mm)
765 Gypsum Plaster Expansion on setting IS:2542 (Part-1) (sec-9)
MATERIALS
MECHANICAL- BUILDINGS Mechanical Resistance of set
766 Gypsum Plaster IS:2542 (Part-1) (sec-7)
MATERIALS neat plaster
Laboratory Name :

performed used
767 Gypsum Plaster Residue on150 micron IS sieve IS:2542 (Part-1) (sec-8)
MATERIALS
768 Gypsum Plaster Setting Time IS:2542 (Part-1) (sec-3)
MATERIALS
769 Gypsum Plaster Soundness IS:2542 (Part-1) (sec-6)
MATERIALS
770 Gypsum Plaster Transverse Strength IS:2542 (Part-1) (sec-4)
MATERIALS
771 Gypsum Plaster Board Dimension (Length) IS:2542 (Part-2)(sec-1)
MATERIALS
772 Gypsum Plaster Board Dimension (Thickness) IS:2542 (Part-2)(sec-1)
MATERIALS
773 Gypsum Plaster Board Dimension (Width) IS:2542 (Part-2)(sec-1)
MATERIALS
774 Gypsum Plaster Board Taper Depth IS:2542 (Part-2)(sec-1)
MATERIALS
775 Gypsum Plaster Board Taper Width IS:2542 (Part-2)(sec-1)
MATERIALS
776 Gypsum Plaster Board Transverse Strength IS:2542 (Part-2)(sec-4)
MATERIALS
777 Hardened Concrete (Cube) Compressive Strength IS 516
MATERIALS
778 Hardened Plaster Pull off adhesion ASTM D 4541
MATERIALS
Deformation & surface
MECHANICAL- BUILDINGS High strength deformed steel bars & wires for concrete
779 characteristics i)Mean Area of IS 1786
MATERIALS reinforcement (TMT Steel Bar )
Rib
780 Elongation IS:1608(Part-1)
781 Mass ATRL/WI/MECH/GEN/006
782 Nominal cross sectional area IS 1786
MECHANICAL- BUILDINGS High strength deformed steel bars & wires for concrete PULL OUT TEST Bond Strength
783 IS 2770 Part-1
MATERIALS reinforcement (TMT Steel Bar ) at a measured slip of 0.25 mm,
MECHANICAL- BUILDINGS High strength deformed steel bars & wires for concrete Pull-out Test Bond Strength at
784 IS 2770 PART 1
MATERIALS reinforcement (TMT Steel Bar ) a measured slip of 0.025 mm,
Laboratory Name :

performed used
785 Re-bend Test IS 1786
786 Tensile Strength IS:1608(Part-1)
MECHANICAL- BUILDINGS High strength deformed steel bars & wires for concrete Total Elongation at maximum
787 IS:1608(Part-1)
MATERIALS reinforcement (TMT Steel Bar ) force
788 0.2 % proof stress/Yield Stress IS:1608(Part-1)
MATERIALS reinforcement (TMT Steel bar)
789 Bend Test IS:1599
MATERIALS reinforcement (TMT Steel bar)
Deformation & surface
790 characteristics Mean Projected IS 1786
MATERIALS reinforcement (TMT steel bar)
Area of Transverse Ribs
791 Laminated Safety Glass Boil & Bake Test IS:17004
MATERIALS
792 Laminated Safety Glass Fracture and Adhesion Test IS:17004
MATERIALS
793 Micro Silica Compressive Strength IS 1727
MATERIALS
794 Micro Silica Density IS 1727
MATERIALS
MECHANICAL- BUILDINGS Oversize percentage retained
795 Micro Silica IS 1727
MATERIALS on 45 micron IS Sieve
796 Ordinary Portland Cement Compressive Strength IS 4031 (P-6)
MATERIALS
797 Ordinary Portland Cement Consistency IS 4031 (P-4)
MATERIALS
798 Ordinary Portland Cement Density IS 4031 (P-11)
MATERIALS
MECHANICAL- BUILDINGS Fineness ( By Blaine's Air
799 Ordinary Portland Cement IS 4031 (P-2)
MATERIALS Permeability)
800 Ordinary Portland Cement Fineness ( By Dry Sieving)) IS 4031 (P-1)
MATERIALS
801 Ordinary Portland Cement Setting Time (Final) 4031 (P-5)
MATERIALS
802 Ordinary Portland Cement Setting Time (Initial) IS 4031 (P-5)
MATERIALS
Laboratory Name :

performed used
MECHANICAL- BUILDINGS Soundness ( By Autoclave test
MATERIALS method)
MECHANICAL- BUILDINGS Soundness (By Le-chatelier
MATERIALS Method)
805 Paver Block Abrasion Resistance IS 15658, Annex-E
MATERIALS
806 Paver Block Arris/Chamfer IS 15658, Annex-B
MATERIALS
807 Paver Block Aspect Ratio IS:15658, Annex-B
MATERIALS
808 Paver Block Compressive Strength IS 15658 , Annex-D
MATERIALS
809 Paver Block Dimension-Length IS 15658, Annex-B
MATERIALS
810 Paver Block Dimension-Thickness IS 15658,Annex-B
MATERIALS
811 Paver Block Dimension-Width IS 15658,Annex-B
MATERIALS
812 Paver Block Flexural Strength IS 15658,Annex-G
MATERIALS
813 Paver Block Split Tensile Strength IS 15658,Annex-F
MATERIALS
814 Paver Block Squareness IS 15658, Annex-B
MATERIALS
815 Paver Block Thickness of wearing layer IS 15658, Annex-B
MATERIALS
816 Paver Block Water Absorption IS 15658 , Annex-C
MATERIALS
817 Paver Block Wearing Face Area IS 15658, Annex-B
MATERIALS
818 Paving Bitumen / Industrial Bitumen Ductility IS 1208
MATERIALS
819 Paving Bitumen / Industrial Bitumen Fire Point IS 1448(P-69)
MATERIALS
820 Paving Bitumen / Industrial Bitumen Flash Point IS 1448(P-69)
MATERIALS
821 Paving Bitumen / Industrial Bitumen Penetration IS 1203
MATERIALS
Laboratory Name :

performed used
822 Paving Bitumen / Industrial Bitumen Softening Point IS 1205
MATERIALS
823 Paving Bitumen / Industrial Bitumen Solubility In Trichloroethylene IS 1216
MATERIALS
824 Plaster Sand Gradation (10~0.15 mm) IS:2386 (P-1)
MATERIALS
825 Portland Slag Cement Compressive Strength IS:4031(Part-6)
MATERIALS
826 Portland Slag Cement Consistancy IS:4031 (Part-4)
MATERIALS
827 Portland Slag Cement Density IS:4031 (Part-11)
MATERIALS
MECHANICAL- BUILDINGS Fineness (By Blaine Air
828 Portland Slag Cement IS:4031 (Part-2)
829 Portland Slag Cement Fineness (By Dry Sieving) IS:4031(Part-1)
MATERIALS
830 Portland Slag Cement Setting Time (Final) IS:4031 (Part-5)
MATERIALS
831 Portland Slag Cement Setting Time (Initial) IS:4031(Part-5)
MATERIALS
832 Portland Slag cement Soundness (By Autoclave) IS: 4031 (Part-3)
MATERIALS
833 Portland Slag Cement Soundness (By Le Chatelier) IS:4031(Part-3)
MATERIALS
834 Portland-Pozzolana Cement Compressive Strength IS 4031 (P-6)
MATERIALS
835 Portland-Pozzolana Cement Consistency IS 4031 (P-4)
MATERIALS
836 Portland-Pozzolana Cement Density IS 4031 (P-11)
MATERIALS
837 Portland-Pozzolana Cement Drying Shrinkage IS 4031 (P-10)
MATERIALS
838 Portland-Pozzolana Cement Fineness ( By Dry Sieving) IS 4031 (P-1)
MATERIALS
MECHANICAL- BUILDINGS Fineness (by Blaine's Air
839 Portland-Pozzolana Cement IS 4031 (P-2)
840 Portland-Pozzolana Cement Setting Time (Final) IS 4031 (P-5)
MATERIALS
Laboratory Name :

performed used
841 Portland-Pozzolana Cement Setting Time (Initial) IS 4031 (P-5)
MATERIALS
MECHANICAL- BUILDINGS Soundness ( By Le-chatelier
MATERIALS Method)
MECHANICAL- BUILDINGS Soundness (By autoclave test
MATERIALS method)
844 precast Concrete pipes(With and without reinforcement ) Barrel wall thickness IS:458
MATERIALS
845 precast Concrete pipes(With and without reinforcement ) Internal Diameter of pipe IS:458
MATERIALS
Minimum number of
846 precast Concrete pipes(With and without reinforcement ) longitudinal mild steel or hard IS:458
MATERIALS
drawn steel
MECHANICAL- BUILDINGS Weight of spiral hard drawn
847 precast Concrete pipes(With and without reinforcement ) IS:458
MATERIALS steel
848 precast Concrete pipes(With and without reinforcement ) Workmanship and finish IS:458
MATERIALS
849 Pulverized fuel ash - lime Bricks Compressive Strength IS:3495(Part-1)
MATERIALS
850 Pulverized fuel ash - lime Bricks Dimension (Height) IS:12894
MATERIALS
851 Pulverized fuel ash - lime Bricks Dimension (Length) IS:12894
MATERIALS
852 Pulverized fuel ash - lime Bricks Dimension (Width) IS:12894
MATERIALS
853 Pulverized fuel ash - lime Bricks Water Absorption IS:3495(Part-2)
MATERIALS
854 Pulverized Fuel Ash lime bricks Dry Shrinkage IS 4139 (Annex-A)
MATERIALS
855 Sand Fineness Modulus ASTM C -136 (Cl.9.2)
MATERIALS
MECHANICAL- BUILDINGS CPWD Specification Vol. 1
856 Sand Silt Content
MATERIALS (APPENDIX-C)
857 Tile Adhesive Adjustability IS 15477, Annex-D
MATERIALS
858 Tile Adhesive Bulk Density IS 2386(P-3)
MATERIALS
Laboratory Name :

performed used
859 Tile Adhesive Compressive Strength 28 Days IS 2250
MATERIALS
860 Tile Adhesive Compressive Strength 3 Days IS:2250
MATERIALS
861 Tile Adhesive Open Time IS 15477
MATERIALS
862 Tile Adhesive Shear Adhesion Strength IS:15477, Annex-B
MATERIALS
863 Tile Adhesive Slip IS:15477, Annex-C
MATERIALS
864 Tile Adhesive Tensile Adhesion Strength IS:15477, Annex-A
MATERIALS
865 Toughened (Tempered) / Laminated Safety Glass Thickness IS:17004
MATERIALS
866 Toughened (Tempered) Safety Glass Fragmentation Test IS:17004
MATERIALS
867 Toughened (Tempered) Safety Glass Resistance to shock IS:17004
MATERIALS
868 Track Ballast Aggregate Abrasion Value IS 2386 (P-4)
MATERIALS
869 Track Ballast Aggregate Impact Value IS 2386 (P-4)
MATERIALS
870 Track Ballast Water Absorption IS 2386 (P-3)
MATERIALS
871 Track Ballest Gradation (53~ 0.75 mm) IS 2386 (P-1)
MATERIALS
872 Water Proofing Compound Compressive Strength 7 Days IS 4031(P-6)
MATERIALS
873 Water Proofing Compound Compressive strength 3 days IS 4031(P-6)
MATERIALS
874 Water Proofing Compound Setting Time (Final) IS 4031(P-5)
MATERIALS
875 Water Proofing Compound Setting Time (Initial) IS 4031(P-5)
MATERIALS
876 Wooden Flush Door Shutters Depth of Indentation IS:4020(Part-5)
MATERIALS
877 Wooden Flush Door Shutters Dimension-Height IS 4020 (P-2)
MATERIALS
Laboratory Name :

performed used
878 Wooden Flush Door Shutters Dimension-Thickness IS 4020 (P-2)
MATERIALS
879 Wooden Flush Door Shutters Dimension-Width IS 4020 (P-2)
MATERIALS
880 Wooden Flush Door Shutters End Immersion Test IS 4020 (P-13)
MATERIALS
881 Wooden Flush Door Shutters General Flatness IS:4020(Part-3)
MATERIALS
882 Wooden Flush Door Shutters Glue Adhesion IS 4020 (P-15)
MATERIALS
883 Wooden Flush Door Shutters Impact Indentation Test IS:4020(Part-5)
MATERIALS
884 Wooden Flush Door Shutters Knife Test IS 4020 (P-14)
MATERIALS
885 Wooden Flush Door Shutters Shock Resistance Test IS:4020(Part-8)
MATERIALS
886 Wooden Flush Door Shutters Squareness IS:4020(Part-2)
MATERIALS
887 Wooden Flush Door Shutters Straightness IS:1659
MATERIALS
MECHANICAL-
888 MECHANICAL PROPERTIES Cast iron /Ductile Iron pipe & fitting Nominal Size ATRL/WI/MECH/GEN/006
OF METALS
MECHANICAL- Cast Iron/Ductile Iron Drainage Pipes and Pipe Fittings for
Coating test at temperature
889 MECHANICAL PROPERTIES Over Ground Non-Pressure Pipeline Socket and Spigot IS 1729
(65 & 0 0C)
OF METALS Series
MECHANICAL- Cast Iron/Ductile Iron Drainage Pipes and Pipe Fittings for
890 MECHANICAL PROPERTIES Over Ground Non-Pressure Pipeline Socket and Spigot Hammer test IS 1729
OF METALS Series
MECHANICAL-
Centrifugally Cast (SPUN) Iron Spigot and Socket soil, waste Coating test at temperature
891 MECHANICAL PROPERTIES IS 3989
and ventilating pipes, fittings and accessories (65 & 0 0C)
OF METALS
MECHANICAL-
Centrifugally Cast (SPUN) Iron Spigot and Socket soil, waste
892 MECHANICAL PROPERTIES Hammer test IS 3989
and ventilating pipes, fittings and accessories
OF METALS
Laboratory Name :

performed used
and ventilating pipes, fittings and accessories/Cast
MECHANICAL- Iron/Ductile Iron Drainage Pipes and Pipe Fittings for Over
893 MECHANICAL PROPERTIES Ground Non-Pressure Pipeline Socket and Spigot Dimensions ATRL/WI/MECH/GEN/006
OF METALS Series/Hubless Centrifugally Cast (SPUN) Iron Pipes, Fittings
& Accessories/Centrifugally cast (SPUN) ductile iron
pressure pipe for water, gas and sewage
and ventilating pipes, fittings and accessories/Cast
MECHANICAL- Iron/Ductile Iron Drainage Pipes and Pipe Fittings for Over
894 MECHANICAL PROPERTIES Ground Non-Pressure Pipeline Socket and Spigot Mass ATRL/WI/MECH/GEN/006:
OF METALS Series/Hubless Centrifugally Cast (SPUN) Iron Pipes, Fittings
& Accessories/Centrifugally cast (SPUN) ductile iron
pressure pipe for water, gas and sewage
MECHANICAL-
895 MECHANICAL PROPERTIES Concertina Coil Diameter of spring wire ATRL/WI/MECH/GEN/006
OF METALS
MECHANICAL-
896 MECHANICAL PROPERTIES Concertina Coil Weight of concertina coil ATRL/WI/MECH/GEN/006
OF METALS
MECHANICAL-
897 MECHANICAL PROPERTIES Galvanized Steel barbed wire Diameter of line wire ATRL/WI/MECH/GEN/006
OF METALS
MECHANICAL-
898 MECHANICAL PROPERTIES Galvanized Steel barbed wire Diameter of point wire ATRL/WI/MECH/GEN/006
OF METALS
MECHANICAL-
899 MECHANICAL PROPERTIES Galvanized steel barbed wire Distance between two barbs IS:278
OF METALS
MECHANICAL-
900 MECHANICAL PROPERTIES Galvanized Steel barbed wire Mass of completed barbed wire ATRL/WI/MECH/GEN/006
OF METALS
MECHANICAL-
901 MECHANICAL PROPERTIES Galvanized Steel Barbed Wire Tensile Strength Of Line Wire IS 1608(P-1)
OF METALS
MECHANICAL-
902 MECHANICAL PROPERTIES Galvanized Steel Strips and Sheet (Corrugated) Dimension- Depth ATRL/WI/MECH/GEN/006
OF METALS
MECHANICAL-
903 MECHANICAL PROPERTIES Galvanized Steel Strips and Sheet (Corrugated) Dimension- Length ATRL/WI/MECH/GEN/006
OF METALS
Laboratory Name :

performed used
MECHANICAL-
904 MECHANICAL PROPERTIES Galvanized Steel Strips and Sheet (Corrugated) Dimension- Thickness ATRL/WI/MECH/GEN/006
OF METALS
MECHANICAL-
905 MECHANICAL PROPERTIES Galvanized Steel Strips and Sheet (Corrugated) Dimension- Width ATRL/WI/MECH/GEN/006
OF METALS
MECHANICAL-
906 MECHANICAL PROPERTIES Galvanized Steel Strips and Sheet (Plain) Bend Test IS 277
OF METALS
MECHANICAL-
907 MECHANICAL PROPERTIES Galvanized Steel Strips and Sheet (Plain) Dimension- Length ATRL/WI/MECH/GEN/006
OF METALS
MECHANICAL-
908 MECHANICAL PROPERTIES Galvanized Steel Strips and Sheet (Plain) Dimension- Thickness ATRL/WI/MECH/GEN/006
OF METALS
MECHANICAL-
909 MECHANICAL PROPERTIES Galvanized Steel Strips and Sheet (Plain) Dimension- Width ATRL/WI/MECH/GEN/006
OF METALS
MECHANICAL-
910 MECHANICAL PROPERTIES Galvanized Steel Strips and Sheet (Plain) Mass ATRL/WI/MECH/GEN/006
OF METALS
MECHANICAL-
911 MECHANICAL PROPERTIES Galvanized Steel Strips and Sheet (Plain) Tensile Strength IS 1608 Part-1
OF METALS
MECHANICAL-
912 MECHANICAL PROPERTIES Galvanized Steel Strips and Sheet (plain/ Corrugated) Freedom from Defects IS 277
OF METALS
MECHANICAL-
913 MECHANICAL PROPERTIES Hollow steel sections for structural use (Hollow Section ) % Elongation IS:1608(Part-1)
OF METALS
MECHANICAL-
914 MECHANICAL PROPERTIES Hollow steel sections for structural use (Hollow Section ) Depth ATRL/WI/MECH/GEN/006
OF METALS
MECHANICAL-
915 MECHANICAL PROPERTIES Hollow steel sections for structural use (Hollow Section ) Tensile Strength IS:1608(Part-1)
OF METALS
MECHANICAL-
916 MECHANICAL PROPERTIES Hollow steel sections for structural use (Hollow Section ) Thickness ATRL/WI/MECH/GEN/006
OF METALS
MECHANICAL-
917 MECHANICAL PROPERTIES Hollow steel sections for structural use (Hollow Section ) Weight ATRL/WI/MECH/GEN/006
OF METALS
Laboratory Name :

performed used
MECHANICAL-
918 MECHANICAL PROPERTIES Hollow steel sections for structural use (Hollow Section ) Width ATRL/WI/MECH/GEN/006
OF METALS
MECHANICAL-
919 MECHANICAL PROPERTIES Hollow steel sections for structural use (Hollow Section ) Yield Stress IS:1608(Part-1)
OF METALS
MECHANICAL-
Hot rolled medium and high tensile structural steel (M.S
920 MECHANICAL PROPERTIES Thickness ATRL/WI/MECH/GEN/006
Tee Bars)
OF METALS
MECHANICAL-
921 MECHANICAL PROPERTIES % Elongation IS:1608(Part-1)
Angle /Beam/Column/Channel Section )
OF METALS
MECHANICAL-
922 MECHANICAL PROPERTIES Dimension ATRL/WI/MECH/GEN/006
OF METALS
MECHANICAL-
923 MECHANICAL PROPERTIES Dimension (Side B ) ATRL/WI/MECH/GEN/006
OF METALS
MECHANICAL-
924 MECHANICAL PROPERTIES Dimension (Side A) ATRL/WI/MECH/GEN/006
OF METALS
MECHANICAL-
925 MECHANICAL PROPERTIES Tensile Strength IS:1608(Part-1)
OF METALS
MECHANICAL-
926 MECHANICAL PROPERTIES Yield Stress IS:1608(Part-1)
OF METALS
MECHANICAL-
Flat /Sheet /Strip/Flat)
OF METALS
MECHANICAL-
OF METALS
MECHANICAL-
OF METALS
MECHANICAL-
930 MECHANICAL PROPERTIES Weight ATRL/WI/MECH/GEN/006
OF METALS
MECHANICAL-
931 MECHANICAL PROPERTIES Yield Stress IS:1608 (Part-1)
OF METALS
Laboratory Name :

performed used
MECHANICAL-
Round Bar/ M.S Square Bar)
OF METALS
MECHANICAL-
933 MECHANICAL PROPERTIES Side width ATRL/WI/MECH/GEN/006
OF METALS
MECHANICAL-
934 MECHANICAL PROPERTIES Tensile Strength IS:1608 (Part-1)
OF METALS
MECHANICAL-
935 MECHANICAL PROPERTIES Weight ATRL/WI/MECH/GEN/006
OF METALS
MECHANICAL-
OF METALS
MECHANICAL-
Hot rolled medium and high tensile structural steel (Beam,
937 MECHANICAL PROPERTIES Root Radius ATRL/WI/MECH/GEN/006:
Column, Channel and angle Section )
OF METALS
MECHANICAL-
Hot rolled Medium and high tensile structural steel (M.S
938 MECHANICAL PROPERTIES Bend Test IS:1599
Plate , Sheet ,Strip and flat)
OF METALS
MECHANICAL-
939 MECHANICAL PROPERTIES Freedom from defects IS:2062
Plate , Sheet ,Strip and flat)
OF METALS
MECHANICAL-
940 MECHANICAL PROPERTIES Diameter of Bar ATRL/WI/MECH/GEN/006
OF METALS
MECHANICAL-
Round, M.S Square bar )
OF METALS
MECHANICAL-
Round, M.S Square bar )
OF METALS
MECHANICAL-
Hot rolled medium and high tensile structural steel (M.S tee
bars )
OF METALS
MECHANICAL-
944 MECHANICAL PROPERTIES Mass ATRL/WI/MECH/GEN/006
Tee Bars)
OF METALS
MECHANICAL-
945 MECHANICAL PROPERTIES Root Radius ATRL/WI/MECH/GEN/006
Tee Bars)
OF METALS
Laboratory Name :

performed used
MECHANICAL-
946 MECHANICAL PROPERTIES Toe Radius ATRL/WI/MECH/GEN/006
Tee Bars)
OF METALS
MECHANICAL-
Hot rolled Medium and tensile structural steel (Beam,
Column, Channel and Angle Section)
OF METALS
MECHANICAL-
OF METALS
MECHANICAL-
949 MECHANICAL PROPERTIES Toe Radius ATRL/WI/MECH/GEN/006
OF METALS
MECHANICAL-
950 MECHANICAL PROPERTIES Hot rolled steel strip for welded tubes and pipes Bend Test IS:1599
OF METALS
MECHANICAL-
951 MECHANICAL PROPERTIES Hot rolled steel strip for welded tubes and pipes Freedom from defects IS:10748
OF METALS
MECHANICAL-
952 MECHANICAL PROPERTIES Hot rolled steel strip for welded tubes and pipes Width ATRL/WI/MECH/GEN/006
OF METALS
MECHANICAL-
Hubless Centrifugally Cast (SPUN) Iron Pipes, Fittings & Coating test at temperature
953 MECHANICAL PROPERTIES IS 15905
Accessories (65 & 0 0C)
OF METALS
MECHANICAL-
Hubless Centrifugally Cast (SPUN) Iron Pipes, Fittings &
954 MECHANICAL PROPERTIES Hammer test IS 15905
Accessories
OF METALS
MECHANICAL-
Mechanical properties of fasteners made for carbon steel
955 MECHANICAL PROPERTIES 0.2% Proof Stress IS 1608 Part-1/ISO 6892-1
and alloy steel-Bolts, Screws and Studs
OF METALS
MECHANICAL-
956 MECHANICAL PROPERTIES Hardness (HRC) IS 1586 (Part-1)
OF METALS
MECHANICAL-
Mechanical properties of fasteners made for carbon steel Percentage Elongation After
957 MECHANICAL PROPERTIES IS 1608 Part-1/ISO 6892-1
and alloy steel-Bolts, Screws and Studs Fraction
OF METALS
MECHANICAL-
958 MECHANICAL PROPERTIES Reduction area after fracture ISO 6892 Part-1
OF METALS
MECHANICAL-
959 MECHANICAL PROPERTIES Tensile strength ISO 6892 Part-1
OF METALS
Laboratory Name :

performed used
MECHANICAL-
960 MECHANICAL PROPERTIES Hardness (HRC) IS 1586 Part-1
and alloy steel-Nut with Specified Properties Classes
OF METALS
MECHANICAL-
961 MECHANICAL PROPERTIES Proof Load ATRL/WI/MECH/GEN/006
and alloy Steel-nut with Specified properties classes
OF METALS
MECHANICAL-
962 MECHANICAL PROPERTIES Metallic Material Charpy Impact Test at RT IS:1757(Part-1)
OF METALS
MECHANICAL-
963 MECHANICAL PROPERTIES Metallic Materials Hardness (HRA) IS 1586 (P-1)
OF METALS
MECHANICAL-
964 MECHANICAL PROPERTIES Metallic Materials Hardness (HRBW) IS 1586 (P-1)
OF METALS
MECHANICAL-
965 MECHANICAL PROPERTIES Metallic Materials Hardness (HRC) IS 1586 Part-1
OF METALS
MECHANICAL-
Mild Steel & Medium tensile steel bars and hard drawn
966 MECHANICAL PROPERTIES 0.2 % Proof Stress IS 1608 Part-1
steel wire for concrete Reinforcement
OF METALS
MECHANICAL-
OF METALS
MECHANICAL-
968 MECHANICAL PROPERTIES Diameter ATRL/WI/MECH/GEN/006
OF METALS
MECHANICAL-
969 MECHANICAL PROPERTIES Freedom from defects IS 432 (Part-1 & 2 )
OF METALS
MECHANICAL-
970 MECHANICAL PROPERTIES Total Elongation IS 1608 Part-1
OF METALS
MECHANICAL-
971 MECHANICAL PROPERTIES Ultimate Tensile Strength IS: 1608 Part-1
OF METALS
MECHANICAL-
Mild steel and medium tensile steel bars and hard drawn
972 MECHANICAL PROPERTIES Nominal Size ATRL/WI/MECH/GEN/006
steel wire
OF METALS
MECHANICAL-
Mild steel and medium tensile steel bars and hard drawn
973 MECHANICAL PROPERTIES Reverse bend IS:1716
steel wire for concrete reinforcement
OF METALS
Laboratory Name :

performed used
MECHANICAL-
974 MECHANICAL PROPERTIES Mild steel wire for general engineering purposes Diameter ATRL/WI/MECH/GEN/006
OF METALS
MECHANICAL-
975 MECHANICAL PROPERTIES Mild steel wire for general engineering purposes Freedom from defects IS 280
OF METALS
MECHANICAL-
976 MECHANICAL PROPERTIES Mild steel wire for general engineering purposes Tensile strength IS 1608(P-1)
OF METALS
MECHANICAL-
977 MECHANICAL PROPERTIES Reinforcement couplers for mechanical splices of bars % Elongation IS:1608(Part-1)
OF METALS
MECHANICAL-
978 MECHANICAL PROPERTIES Reinforcement couplers for mechanical splices of bars Location of failure IS:16172
OF METALS
MECHANICAL-
979 MECHANICAL PROPERTIES Reinforcement couplers for mechanical splices of bars Slip test IS:16172
OF METALS
MECHANICAL-
980 MECHANICAL PROPERTIES Reinforcement couplers for mechanical splices of bars Tensile Strength IS:1608(Part-1)
OF METALS
MECHANICAL-
981 MECHANICAL PROPERTIES Steel Chequered Plates Tensile Strength IS:1608(Part-1)
OF METALS
MECHANICAL-
982 MECHANICAL PROPERTIES Steel Chequered Plates Width ATRL/WI/MECH/GEN/006
OF METALS
MECHANICAL-
983 MECHANICAL PROPERTIES Steel Chequered Plates % Elongation IS:1608(Part-1)
OF METALS
MECHANICAL-
984 MECHANICAL PROPERTIES Steel Chequered Plates Bend Test IS:1599
OF METALS
MECHANICAL-
985 MECHANICAL PROPERTIES Steel Chequered Plates Chequered Height ATRL/WI/MECH/GEN/006
OF METALS
MECHANICAL-
986 MECHANICAL PROPERTIES Steel Chequered Plates Freedom from Defects IS:3502
OF METALS
MECHANICAL-
987 MECHANICAL PROPERTIES Steel Chequered Plates Thickness ATRL/WI/MECH/GEN/006
OF METALS
Laboratory Name :

performed used
MECHANICAL-
988 MECHANICAL PROPERTIES Steel Chequered Plates Yield Stress IS:1608(Part-1)
OF METALS
MECHANICAL-
Steel pipe for water and sewage (168.3 to 2540 mm
989 MECHANICAL PROPERTIES Outside diameter ATRL/WI/MECH/GEN/006
outside diameter )
OF METALS
MECHANICAL-
Steel pipe for water and sewage (168.3 to 2540mm outside
diameter )
OF METALS
MECHANICAL-
diameter )
OF METALS
MECHANICAL-
diameter )
OF METALS
MECHANICAL-
993 MECHANICAL PROPERTIES Flattening test IS:2328
diameter )
OF METALS
MECHANICAL-
994 MECHANICAL PROPERTIES Guided bend test IS:3589
diameter )
OF METALS
MECHANICAL-
995 MECHANICAL PROPERTIES Height of internal welded bead ATRL/WI/MECH/GEN/006
diameter )
OF METALS
MECHANICAL-
996 MECHANICAL PROPERTIES Mass ATRL/WI/MECH/GEN/006
diameter )
OF METALS
MECHANICAL-
diameter )
OF METALS
MECHANICAL-
Steel pipe for water and sewage (168.3 to 2540mm outside Visual inspection ,appearance
998 MECHANICAL PROPERTIES IS:3589
diameter ) and workmanship
OF METALS
MECHANICAL-
999 MECHANICAL PROPERTIES Steel tubes & tubular % Elongation IS:1608(Part-1)
OF METALS
MECHANICAL-
1000 MECHANICAL PROPERTIES Steel tubes & tubular Adhesion test IS 2629
OF METALS
MECHANICAL-
1001 MECHANICAL PROPERTIES Steel tubes & tubular Free bore test IS 4736
OF METALS
Laboratory Name :

performed used
MECHANICAL-
1002 MECHANICAL PROPERTIES Steel tubes & tubular Mass ATRL/WI/MECH/GEN/006
OF METALS
MECHANICAL-
1003 MECHANICAL PROPERTIES Steel tubes & tubular Outer Diameter ATRL/WI/MECH/GEN/006
OF METALS
MECHANICAL-
1004 MECHANICAL PROPERTIES Steel tubes & tubular Straightness IS 1161
OF METALS
MECHANICAL-
1005 MECHANICAL PROPERTIES Steel tubes & tubular Tensile Strength IS:1608(Part-1)
OF METALS
MECHANICAL-
1006 MECHANICAL PROPERTIES Steel tubes & tubular Thickness ATRL/WI/MECH/GEN/006
OF METALS
MECHANICAL-
1007 MECHANICAL PROPERTIES Steel tubes & tubular Workmanship IS 1161
OF METALS
MECHANICAL-
1008 MECHANICAL PROPERTIES Steel tubes & tubular Workmanship IS 1239(P-1)
OF METALS
MECHANICAL-
1009 MECHANICAL PROPERTIES Steel tubes & tubulars Bend test IS 2329
OF METALS
MECHANICAL-
1010 MECHANICAL PROPERTIES Steel tubes & tubulars Flattening test IS 2328
OF METALS
MECHANICAL-
Height of internal weld
1011 MECHANICAL PROPERTIES Steel tubes & tubulars IS 1239(P-1)
fin(welded tube)
OF METALS
MECHANICAL-
1012 MECHANICAL PROPERTIES Steel tubes and tubular and other wrought steel fittings Bend Test (Strip) IS:3601
OF METALS
MECHANICAL-
1013 MECHANICAL PROPERTIES Steel tubes and tubular and other wrought steel fittings Crushing Test IS:3601
OF METALS
MECHANICAL-
1014 MECHANICAL PROPERTIES Steel tubes and tubular and other wrought steel fittings Drift expansion test IS:2335
OF METALS
MECHANICAL-
1015 MECHANICAL PROPERTIES Steel tubes and tubular and other wrought steel fittings Mass ATRL/WI/MECH/GEN/006
OF METALS
Laboratory Name :

performed used
MECHANICAL-
1016 MECHANICAL PROPERTIES Steel tubes and tubular and other wrought steel fittings Straightness IS:3601
OF METALS
MECHANICAL-
1017 MECHANICAL PROPERTIES Steel tubes and tubular and other wrought steel fittings Thickness ATRL/WI/MECH/GEN/006
OF METALS
MECHANICAL-
1018 MECHANICAL PROPERTIES Steel tubes and tubular and other wrought steel fittings workmanship IS:3601
OF METALS
MECHANICAL-
1019 MECHANICAL PROPERTIES Steel tubes for mechanical & general Engineering purposes Tensile Strength IS:1608(Part-1)
OF METALS
MECHANICAL-
Steel tubes for mechanical and general engineering
purposes
OF METALS
MECHANICAL-
1021 MECHANICAL PROPERTIES Outside Diameter ATRL/WI/MECH/GEN/006
purposes
OF METALS
MECHANICAL-
purposes
OF METALS
MECHANICAL-
1023 MECHANICAL PROPERTIES Steel Tubes for Structural Purpose( M.S Pipe) Mass ATRL/WI/MECH/GEN/006
OF METALS
MECHANICAL-
1024 MECHANICAL PROPERTIES Steel Tubes for Structural Purpose( M.S Pipe) % Elongation IS:1608(Part-1)
OF METALS
MECHANICAL-
1025 MECHANICAL PROPERTIES Steel Tubes for Structural Purpose( M.S Pipe) Outer Diameter ATRL/WI/MECH/GEN/006
OF METALS
MECHANICAL-
1026 MECHANICAL PROPERTIES Steel Tubes for Structural Purpose( M.S Pipe) Tensile Strength IS:1608(Part-1)
OF METALS
MECHANICAL-
1027 MECHANICAL PROPERTIES Steel Tubes for Structural Purpose( M.S Pipe) Yield Stress IS:1608(Part-1)
OF METALS
MECHANICAL-
1028 MECHANICAL PROPERTIES Steel Tubes used for water wells % Elongation IS:1608(Part-1)
OF METALS
MECHANICAL-
Coating test at temperature
1029 MECHANICAL PROPERTIES Steel tubes used for water wells IS:4270
(65 & 0 0C)
OF METALS
Laboratory Name :

performed used
MECHANICAL-
1030 MECHANICAL PROPERTIES Steel tubes used for water wells Mass of plain tube ATRL/WI/MECH/GEN/006
OF METALS
MECHANICAL-
1031 MECHANICAL PROPERTIES Steel tubes used for water wells Outside diameter ATRL/WI/MECH/GEN/006
OF METALS
MECHANICAL-
1032 MECHANICAL PROPERTIES Steel tubes used for water wells Outside diameter of sockets ATRL/WI/MECH/GEN/006
OF METALS
MECHANICAL-
1033 MECHANICAL PROPERTIES Steel tubes used for water wells Overall length of sockets IS:4270
OF METALS
MECHANICAL-
1034 MECHANICAL PROPERTIES Steel tubes used for water wells Straightness IS:4270
OF METALS
MECHANICAL-
1035 MECHANICAL PROPERTIES Steel Tubes used for water wells Tensile Strength IS:1608(Part-1)
OF METALS
MECHANICAL-
1036 MECHANICAL PROPERTIES Steel tubes used for water wells Thickness ATRL/WI/MECH/GEN/006
OF METALS
MECHANICAL-
1037 MECHANICAL PROPERTIES Steel tubes used for water wells Workmanship IS:4270
OF METALS
MECHANICAL-
1038 MECHANICAL PROPERTIES Steel Tubes used for water wells Yield Stress IS:1608(Part-1)
OF METALS
MECHANICAL-
Uncoated Stress relieved low relaxation seven ply strand
1039 MECHANICAL PROPERTIES Relaxation Test IS:14268
wire for prestressed concrete
OF METALS
MECHANICAL-
Uncoated stress relieved low relaxation seven ply strand
1040 MECHANICAL PROPERTIES Breaking strength IS 1608(P-1)
wire
OF METALS
MECHANICAL-
Uncoated stress relieved low relaxation seven ply strand Diameter difference between
1041 MECHANICAL PROPERTIES ATRL/WI/MECH/GEN/006
wire centre and surrounding wire
OF METALS
MECHANICAL-
1042 MECHANICAL PROPERTIES Length of lay ATRL/WI/MECH/GEN/006
wire
OF METALS
MECHANICAL-
1043 MECHANICAL PROPERTIES Nominal area ATRL/WI/MECH/GEN/006
wire
OF METALS
Laboratory Name :

performed used
MECHANICAL-
1044 MECHANICAL PROPERTIES Nominal diameter ATRL/WI/MECH/GEN/006
wire
OF METALS
MECHANICAL-
1045 MECHANICAL PROPERTIES Nominal mass ATRL/WI/MECH/GEN/006
wire
OF METALS
MECHANICAL-
1046 MECHANICAL PROPERTIES Workmanship & Finish IS 14268
wire
OF METALS
MECHANICAL-
Uncoated Stress relieved low relaxation seven ply strand % Elongation on 600 mm
1047 MECHANICAL PROPERTIES IS:1608(Part-1)
wire for prestressed concrete Gauge Length
OF METALS
MECHANICAL-
1048 MECHANICAL PROPERTIES 0.2 % proof load IS:1608(Part-1)
OF METALS
MECHANICAL-
1049 MECHANICAL PROPERTIES Modulus of elasticity IS:1608(Part-1)
OF METALS
MECHANICAL-
1050 MECHANICAL PROPERTIES Welds & welded specimens Transverse Face bend IS 3600(P-5)
OF METALS
MECHANICAL-
1051 MECHANICAL PROPERTIES Welds & welded test specimen Transverse tensile strength ASME SECTION IX
OF METALS
MECHANICAL-
1052 MECHANICAL PROPERTIES welds & welded test specimen Transverse tensile strength IS 3600(P-3)
OF METALS
MECHANICAL-
1053 MECHANICAL PROPERTIES Welds & welded test specimens Macro Examination ASME Section- IX
OF METALS
MECHANICAL-
1054 MECHANICAL PROPERTIES Welds & welded test specimens Macro Examination IS 3600 (Part-9)
OF METALS
MECHANICAL-
1055 MECHANICAL PROPERTIES Welds & welded test specimens All weld tensile test IS 3600(P-4)
OF METALS
MECHANICAL-
1056 MECHANICAL PROPERTIES Welds & welded test specimens Face bend ASME SECTION IX
OF METALS
MECHANICAL-
1057 MECHANICAL PROPERTIES Welds & welded test specimens Fillet weld fracture test ASME SECTION IX
OF METALS
Laboratory Name :

performed used
MECHANICAL-
1058 MECHANICAL PROPERTIES Welds & welded test specimens Fillet weld fracture test IS 3600(P-1)
OF METALS
MECHANICAL-
1059 MECHANICAL PROPERTIES Welds & welded test specimens Longitudinal Face bend IS 3600(P-7)
OF METALS
MECHANICAL-
1060 MECHANICAL PROPERTIES Welds & welded test specimens Longitudinal Root bend IS 3600(P-7)
OF METALS
MECHANICAL-
1061 MECHANICAL PROPERTIES Welds & welded test specimens Root bend ASME SECTION IX
OF METALS
MECHANICAL-
1062 MECHANICAL PROPERTIES Welds & welded test specimens Side bend ASME SECTION IX
OF METALS
MECHANICAL-
1063 MECHANICAL PROPERTIES Welds & welded test specimens Side bend IS 3600(P-6)
OF METALS
MECHANICAL-
1064 MECHANICAL PROPERTIES Welds & welded test specimens Transverse Root bend IS 3600(P-5)
OF METALS
MECHANICAL-
1065 MECHANICAL PROPERTIES Wire loop Breaking Load ATRL/WI/MECH/GEN/006
OF METALS
MECHANICAL-
Wrought Aluminium Alloys Drawn Tube for General
1066 MECHANICAL PROPERTIES Freedom From Defects IS 738
Engineering Purposes
OF METALS
MECHANICAL-
Wrought Aluminium & its Alloys Drawn Tube for General
1067 MECHANICAL PROPERTIES 0.2 % Proof Stress IS 1608(P-1)
OF METALS
MECHANICAL-
1068 MECHANICAL PROPERTIES Nominal outside diameter ATRL/WI/MECH/GEN/006
OF METALS
MECHANICAL-
1069 MECHANICAL PROPERTIES Nominal wall thickness ATRL/WI/MECH/GEN/006
OF METALS
MECHANICAL-
1070 MECHANICAL PROPERTIES Percent Elongation IS 1608(P-1)
OF METALS
MECHANICAL-
1071 MECHANICAL PROPERTIES Tensile Strength IS 1608(P-1)
OF METALS
Laboratory Name :

performed used
MECHANICAL-
Wrought Aluminium and Aluminium Alloy Bars, Rods and
Sections for General Engineering Purposes
OF METALS
MECHANICAL-
1073 MECHANICAL PROPERTIES Elongation IS 1608(P-1)
OF METALS
MECHANICAL-
OF METALS
MECHANICAL-
OF METALS
MECHANICAL-
Wrought aluminium and aluminium alloy sheet and strip for
general engineering purposes
OF METALS
MECHANICAL-
Wrought Aluminium and Aluminium Alloy Sheet and Strip
for General Engineering Purposes
OF METALS
MECHANICAL-
OF METALS
MECHANICAL-
1079 MECHANICAL PROPERTIES Percent Elongation IS 1608(P-1)
OF METALS
MECHANICAL-
OF METALS
MECHANICAL-
1081 MECHANICAL PROPERTIES Thickness of sheet/ strip ATRL/WI/MECH/GEN/006
OF METALS
MECHANICAL-
Wrought aluminium and aluminium alloys bars , rod and
1082 MECHANICAL PROPERTIES Diameter of rod ATRL/WI/MECH/GEN/006
sections for general engineering purposes
OF METALS
MECHANICAL-
OF METALS
MECHANICAL-
1084 MECHANICAL PROPERTIES Thickness of regular section ATRL/WI/MECH/GEN/006
OF METALS
MECHANICAL-
1085 MECHANICAL PROPERTIES Width of hexagonal bar ATRL/WI/MECH/GEN/006
OF METALS
Laboratory Name :

performed used
MECHANICAL-
1086 MECHANICAL PROPERTIES Width of regular section ATRL/WI/MECH/GEN/006
OF METALS
MECHANICAL-
1087 MECHANICAL PROPERTIES Width of square bar ATRL/WI/MECH/GEN/006
OF METALS
MECHANICAL- Wrought Aluminium and Aluminium Alloys Extruded Round
1088 MECHANICAL PROPERTIES Tube and Hollow Sections for General Engineering 0.2 % Proof Stress IS 1608(P-1)
OF METALS Purposes.
1089 MECHANICAL PROPERTIES Tube and Hollow Sections for General Engineering Freedom From Defects IS 1285
OF METALS Purposes.
1090 MECHANICAL PROPERTIES Tube and Hollow Sections for General Engineering Percent Elongation IS 1608(P-1)
OF METALS Purposes.
1091 MECHANICAL PROPERTIES Tube and Hollow Sections for General Engineering Tensile Strength IS 1608(P-1)
OF METALS Purposes.
MECHANICAL- PLASTICS
1092 Aluminium Composite Panel/Sheet(ACP) Elongation at break % ASTM E8
AND PLASTIC PRODUCTS
1093 Aluminium Composite Panel/Sheet(ACP) Tensile Strength ASTM E8
1094 Aluminium Composite Panel/Sheet(ACP) Thickness ATRL/WI/MECH/GEN006
1095 Aluminium Composite Panel/Sheet(ACP) Weight ATRL/WI/MECH/GEN006
1096 APP Bituminous Sheet Dimension Stability ASTM D-5147
1097 APP Bituminous Sheet Elongation ASTM D -5147
1098 APP Bituminous Sheet Moisture Content ASTM D-5147
1099 APP Bituminous Sheet Peak Load ASTM D -5147
1100 APP Bituminous Sheet Tear Strength ASTM D5147
1101 APP Bituminous Sheet Thickness ASTM D- 6222
1102 APP Bituminous Sheet Unit Weight ASTM D -6222
Laboratory Name :

performed used
1103 APP Bituminous Sheet Water Absorption ASTM D -5147
MECHANICAL- PLASTICS Chlorinated Polyvinyl chloride pipes for potable hot and
1104 Colour of Pipe IS:15778
AND PLASTIC PRODUCTS cold water distribution supplies
1105 Density IS:12235(Part-14)
1106 Dimension( Outside Diameter) IS:15778
1107 Effective Length IS:15778
1108 Flattening Test IS:12235(Part-19)
1109 Hydraulic Characteristics IS:12235(Part-8/S-1)
MECHANICAL- PLASTICS Chlorinated Polyvinyl chloride pipes for potable hot and Mean outside diameter at any
1110 IS:12235(P-1)
AND PLASTIC PRODUCTS cold water distribution supplies point
1111 Opacity IS:12235(Part-3)
1112 Outside Diameter IS:12235(P-1)
1113 Pipe Ends IS:15778
MECHANICAL- PLASTICS Chlorinated Polyvinyl chloride pipes for potable hot and Resistance to external blows at
1114 IS:4985
AND PLASTIC PRODUCTS cold water distribution supplies 0 degree C
1115 Reversion Test IS:12235(Part-5)
MECHANICAL- PLASTICS Chlorinated Polyvinyl chloride pipes for potable hot and Thermal Stability by
1117 IS:12235(Part-8/S-1)
AND PLASTIC PRODUCTS cold water distribution supplies hydrostatic pressure
Verification of the Malfunction
1118 Temperature at 95 +- 2degree IS:15778 Annex -2
C for 1000 h
1119 Vicat Softening Temperature IS:12235(Part-2)
1120 Visual Appearance IS:15778
Laboratory Name :

performed used
1121 Wall Thickness IS:12235(P-1)
1122 Irrigation Equipment Pe Pipe for irrigation Laterals Dimension (Outside Diameter ) IS:12786
MECHANICAL- PLASTICS Hydraulic Characteristics -
1123 Irrigation Equipment pe pipe for irrigation laterals IS:12786(Annexure-C)
AND PLASTIC PRODUCTS Acceptance Test
1124 Irrigation Equipment pe pipe for irrigation laterals IS:12786(Annexure-C)
AND PLASTIC PRODUCTS Type Test
1125 Irrigation Equipment pe pipe for irrigation laterals Reversion Test IS:12786
MECHANICAL- PLASTICS Susceptibility to environment
1126 Irrigation Equipment pe pipe for irrigation laterals IS:12786(Annexure-D)
AND PLASTIC PRODUCTS stress cracking
1127 Irrigation Equipment pe pipe for irrigation laterals Tensile Test IS:2530
1128 Irrigation Equipment pe pipe for irrigation laterals Visual Appearance IS:12786
1129 Irrigation Equipment Pe Pipe for irrigation Laterals Wall Thickness IS:12786
1130 Irrigation Equipment Sprinkler Outside Diameter IS 14151(P-1)
1131 Irrigation Equipment Sprinkler Pipe Carbon Black Dispersion IS 2530
1132 Irrigation Equipment Sprinkler Pipes Carbon Black Content IS 2530
1133 Irrigation Equipment Sprinkler Pipes Density IS 7328
1134 Irrigation Equipment Sprinkler Pipes Elongation at break IS 14151(P-1)
Fusion Compatibility Test- 1)
1135 Irrigation Equipment Sprinkler Pipes Acceptance Test 2) Quality IS 14151(P-1)
Test
Hydrostatic Characteristics: 1)
1136 Irrigation Equipment Sprinkler Pipes Acceptance Test 2) Quality IS 14151(P-1)(Annexure A)
Test
1137 Irrigation Equipment Sprinkler Pipes Melt Flow Index IS 2530
1138 Irrigation Equipment Sprinkler Pipes Ovality IS 14151(P-1)
Laboratory Name :

performed used
1139 Irrigation Equipment Sprinkler Pipes Reversion Test IS 14151(P-1)
1140 Irrigation Equipment Sprinkler Pipes Tensile Strength IS 14151(P-1)
1141 Irrigation Equipment Sprinkler Pipes Visual Appearance IS 14151(P-1)
1142 Irrigation Equipment Sprinkler Pipes Wall Thickness IS 14151(P-1)
1143 Irrigation Equipment Sprinkler Pipes- PE Pipe Carbon Black Content IS:2530
1144 Irrigation Equipment Sprinkler Pipes- PE Pipe Carbon Black Dispersion IS:2530
1145 Irrigation Equipment Sprinkler Pipes- PE Pipe Density IS:7328
1146 Irrigation Equipment Sprinkler Pipes- PE Pipe Dimension (Outside Diameter) IS:14151(Part-1)
1147 Irrigation Equipment Sprinkler Pipes- PE Pipe Elongation at break IS:14151(Part-1)
MECHANICAL- PLASTICS Fusion Compability Test -
1148 Irrigation Equipment Sprinkler Pipes- PE Pipe IS:14151(Part-1)
AND PLASTIC PRODUCTS Quality Test
MECHANICAL- PLASTICS Fusion Compatibility Test-
1149 Irrigation Equipment Sprinkler Pipes- PE Pipe IS:14151(Part-1)
Hydrostatic Characteristics-
1150 Irrigation Equipment Sprinkler Pipes- PE Pipe i)Acceptance Test II)Quality IS:14151(Part-1) Annexure-A
Test
1151 Irrigation Equipment Sprinkler Pipes- PE Pipe Melt Flow Index IS:2530
1152 Irrigation Equipment Sprinkler Pipes- PE Pipe Ovality IS:14151(Part-1)
1153 Irrigation Equipment Sprinkler Pipes- PE Pipe Reversion Test IS:14151(Part-1)
1154 Irrigation Equipment Sprinkler Pipes- PE Pipe Tensile Strength IS:14151(Part-1)
1155 Irrigation Equipment Sprinkler Pipes- PE Pipe Visual Appearance IS:14151(Part-1)
1156 Irrigation Equipment Sprinkler Pipes- PE Pipe Wall Thickness IS:14151 (Part-1)
Laboratory Name :

performed used
1157 Pe Pipe For Water Supply Carbon Black Content IS:2530
1158 Pe Pipe For Water Supply Carbon Black Dispersion IS:2530
1159 Pe Pipe For Water Supply Density IS:7328
1160 Pe Pipe for water Supply Dimension (Outside Diameter ) IS:4984
1161 Pe Pipe For Water Supply Elongation at break IS:4984(Annexure-H)
Internal Pressure creep rupture
1162 Pe Pipe for Water Supply test of pipe 80 degree C IS:4984
(48,100,165,1000 hrs.)
1163 Pe Pipe for water supply test of pipe joints 80 degree IS:4984
C(48 hrs.)
1164 Pe Pipe For Water Supply Melt Flow Rate IS:2530
1165 Pe Pipe For Water Supply Overall Migration IS:10146
1166 Pe Pipe For Water Supply Overall Migration IS:9845
1167 Pe Pipe For Water Supply Oxidation Induction Time IS:4984(Annexure-B)
1168 Pe Pipe For Water Supply Reversion Test IS:4984(Annexure-F)
1169 Pe Pipe for water Supply Slow Crack growth rate IS:4984(Annexure-E)
1170 Pe Pipe For Water Supply Tensile Strength for Butt fusion IS:4984(Annexure-G)
1171 Pe-Pipe for water supply Colour IS:4984
1172 Pe-Pipe for water supply Depth of Strips IS:4984
1173 Pe-Pipe for water supply Dimension (Outside Diameter) IS:4984
Laboratory Name :

performed used
Hydraulic Characteristics
MECHANICAL- PLASTICS internal pressure creep rupture
1174 Pe-Pipe for water supply IS:4984
AND PLASTIC PRODUCTS test of pipe at 27 degree C( 1
hour)
MECHANICAL- PLASTICS Identification of strip (Number
AND PLASTIC PRODUCTS of Strips )
MECHANICAL- PLASTICS Maximum out of square of pipe
AND PLASTIC PRODUCTS end
1177 Pe-Pipe for water supply Ovality IS:4984
1178 Pe-Pipe for water supply Visual Appearance IS:4984
1179 Pe-Pipe for water supply Wall Thickness IS:4984
1180 Pe-Pipe for water supply Width of Strips IS:4984
1181 Plastic film Colour IS:2508
1182 Plastic Film Tensile Strength IS:13360(P-5), Section 1
1183 Plastic Film Visual Appearance IS:2508
1184 Plastic Films Carbon Black Content IS:2530
1185 Plastic Films Carbon Black Dispersion IS:2530
1186 Plastic Films Density ASTM D-297
1187 Plastic Films Density IS:13360 (P-3)/Sec-10
1188 Plastic Films Density IS:7328
1189 Plastic Films Elongation at break ( %) IS:13360(P-5) Section-1
1190 Plastic Films Elongation at break ( %) IS:13360(P-5) Section-3
1191 Plastic Films Melt Flow Rate IS: 13360(P-4) Section-1
Laboratory Name :

performed used
1192 Plastic Films Tensile Strength IS:13360(P-5) Section-3
1193 Plastic Films Thickness IS:2508
1194 Plastic Sheet Carbon Black Content IS 2530
1195 Plastic Sheet Carbon Black Dispersion IS 2530
1196 Plastic Sheet Colour IS 10889
1197 Plastic Sheet Density ASTM D297
1198 Plastic Sheet Density IS 13630(P-3) Section-1
1199 Plastic Sheet Density IS 7328
1200 Plastic Sheet Elongation IS 13360(P-5) Section-1
1201 Plastic Sheet Elongation IS 13360(P-5) Secton-3
1202 Plastic Sheet Melt Flow Rate IS 13360(P-4) Section-1
1203 Plastic Sheet Tensile Strength IS 13360(P-5) Section-1
1204 Plastic Sheet Tensile Strength IS 13360(P-5) Section-3
1205 Plastic Sheet Thickness IS:10889
1206 Plastic Sheet Visual Appearance IS 10889
MECHANICAL- PLASTICS Polyethylene pipes for sewerage and industrial chemicals
1207 Carbon Black Content IS:2530
AND PLASTIC PRODUCTS and effluent
1208 Carbon Black Dispersion IS:7328
1209 Density IS:7328(Annexure-A)
1210 Dimension- Outside Diameter IS:14333
Laboratory Name :

performed used
Hydraulic Characteristics -
MECHANICAL- PLASTICS Polyethylene pipes for sewerage and industrial chemicals Internal Pressure Creep
1211 IS 4984, Annex-E
AND PLASTIC PRODUCTS and effluent Rupture test of pipe joints ( 80
0C for 48 Hrs)
MECHANICAL- PLASTICS Polyethylene pipes for sewerage and industrial chemicals Hydraulic Characteristics Test-
1212 IS: 4984, Annex-E
AND PLASTIC PRODUCTS and effluent Internal Pressure Rupture Test
1213 Longitudinal Reversion Test IS 4984, Annex-F
1214 Melt Flow Rate IS:2530
1215 Ovality IS:14333
1217 Wall Thickness IS:14333
1218 Polyethylene Pipes for the supply of gaseous fuels Reversion Test IS:14885(Annexure-C)
1219 Polyethylene Pipes for the supply of gaseous fuels Squeeze Off IS:14885(Annexure-G)
1220 Polyethylene Pipes for the supply of gaseous fuels Colour IS:14885
1221 Polyethylene Pipes for the supply of gaseous fuels Density IS:7328
MECHANICAL- PLASTICS Dimension of pipe (Normal Out
1222 Polyethylene Pipes for the supply of gaseous fuels IS:14885
AND PLASTIC PRODUCTS side Diameter )
MECHANICAL- PLASTICS Effect of gas constituents on
AND PLASTIC PRODUCTS the hydrostatic strength
1224 Polyethylene Pipes for the supply of gaseous fuels Elongation at Break IS:14885(Annexure-J)
1225 Polyethylene Pipes for the supply of gaseous fuels Finish IS:14885
1226 Polyethylene Pipes for the supply of gaseous fuels test for plain and notched IS:14885(Annexure-A
pipes at 20 degree C
1227 Polyethylene Pipes for the supply of gaseous fuels test for plain and notched IS:14885(Annexure-A)
pipes at 80 degree c
Laboratory Name :

performed used
MECHANICAL- PLASTICS Maximum out of square of
AND PLASTIC PRODUCTS each pipe end
1229 Polyethylene Pipes for the supply of gaseous fuels Melt flow Rate IS:2530
1230 Polyethylene Pipes for the supply of gaseous fuels Ovality IS:14885
Pe Compound Quality
1231 Polyethylene Pipes for the supply of gaseous fuels Evaluation – Conventional IS:7328
Density
MECHANICAL- PLASTICS Pe Compound Quality
AND PLASTIC PRODUCTS Evaluation – Melt Flow Rate
Pe Compound Quality
1233 Polyethylene Pipes for the supply of gaseous fuels Evaluation - Pigment IS:14885
Dispersion
Pe Compound Quality
1234 Polyethylene Pipes for the supply of gaseous fuels Evaluation – Resistance to IS:14885
constituents
MECHANICAL- PLASTICS Pe Compound Quality
AND PLASTIC PRODUCTS Evaluation – Thermal Stability
1236 Polyethylene Pipes for the supply of gaseous fuels Pigment Dispersion IS:14885(Annexure-E)
MECHANICAL- PLASTICS Resistance to weathering –
1237 Polyethylene Pipes for the supply of gaseous fuels IS:14885(Annexure-F)
AND PLASTIC PRODUCTS Elongation at break
AND PLASTIC PRODUCTS Hydrostatic Strength
AND PLASTIC PRODUCTS Oxygen Index Test
1240 Polyethylene Pipes for the supply of gaseous fuels Tensile Strength IS:14885(Annexure-J)
MECHANICAL- PLASTICS Thermal Stability to oxidation
1241 Polyethylene Pipes for the supply of gaseous fuels IS :14885(Annexure-D)
AND PLASTIC PRODUCTS (OIT)
1242 Polyethylene Pipes for the supply of gaseous fuels Volatile Matter Content IS:14885(Annexure-H)
1243 Polyethylene Pipes for the supply of gaseous fuels Wall Thickness IS:14885
MECHANICAL- PLASTICS Polypropylene random copolymer pipe for hot & cold water
1244 Carbon Black Content IS:2530
AND PLASTIC PRODUCTS supplies
1245 Carbon Black Dispersion Test IS:2530
Laboratory Name :

performed used
1247 Diameter At any point IS:15801
MECHANICAL- PLASTICS Polypropylene random copolymer pipe for hot & cold water Dimension (Mean outside
1248 IS:15801
AND PLASTIC PRODUCTS supplies Diameter )
1249 Fusion Compatibility Test IS:15801
MECHANICAL- PLASTICS Polypropylene random copolymer pipe for hot & cold water Hydraulic Characteristics -
1250 IS:12235(Part-8/S-1)
AND PLASTIC PRODUCTS supplies Acceptance Test
MECHANICAL- PLASTICS Polypropylene random copolymer pipe for hot & cold water Hydraulic Characteristics -
1251 IS:12235(Part-8/S-1)
AND PLASTIC PRODUCTS supplies Type Test
1252 Length IS:15801
1253 Mean outside diameter IS:15801
1254 Melt Flow Rate IS:13360(Part-4/Sec-1)
1255 Opacity IS:12235(Part-3)
1256 Reversion Test IS:12235(Part-5/S-1)
MECHANICAL- PLASTICS Polypropylene random copolymer pipe for hot & cold water Thermal Stability by
1257 IS:12235 (Part-8/S-1)
AND PLASTIC PRODUCTS supplies hydrostatic Pressure
1259 Wall Thickness IS:15801
1260 PVC Water Stop Accelerated Extraction IS:15058(Annexure-B)
Cold Bend Test
(4.00,6.00,8.04,12.00,14.10,16
.02,18.27,19.98,23.24,25.56,2
1261 PVC Water Stop 8.06,30.02,31.96,35.10,40.09, IS 9766 (Annexure-G)
45.05,48.03,52.06,54.05,60.03
,70.94,80.02,84.98,90.14,100.
06,109.97 mm)
1262 PVC Water Stop Dimension -Thickness IS:15058
Laboratory Name :

performed used
1263 PVC Water Stop Effect of Akali IS:15058(Annexure-C)
1264 PVC Water Stop Elongation at break % IS:13360(Part-5/Sec-1)
1265 PVC Water Stop Hardness IS:13360(Part-5/Sec-11)
1266 PVC Water Stop Tensile Strength IS:13360(Part-5/Sec-1)
1267 PVC Water Stop Water Absorption IS:15058(Annexure-A)
1268 Quick Coupled Polyethylene Pipe and fittings Carbon Black Content IS:2530
1269 Quick Coupled Polyethylene Pipe and fittings Carbon Black Dispersion IS:2530
Change in hardness after
1270 Quick Coupled Polyethylene Pipe and fittings keeping it in air at 70 degree C IS:14151(Part-2)
for 7 days
1271 Quick Coupled Polyethylene Pipe and fittings Density IS:7328
1272 Quick Coupled Polyethylene Pipe and fittings Dimension- Outside Diameter IS:14151(Part-1)
MECHANICAL- PLASTICS Fusion Capabilities Test -
1273 Quick Coupled Polyethylene Pipe and fittings IS:14151(Part-1)
MECHANICAL- PLASTICS Fusion Compatibility Test -
MECHANICAL- PLASTICS Hydraulic characteristics -
1275 Quick Coupled Polyethylene Pipe and fittings IS:14151 (Part-1)
MECHANICAL- PLASTICS Hydraulic Characteristics -Type
AND PLASTIC PRODUCTS Test
1277 Quick Coupled Polyethylene Pipe and fittings Hydraulic Proof Test IS:14151(Part-2
1278 Quick Coupled Polyethylene Pipe and fittings Leakage Test IS:14151 (Part-2)
1279 Quick Coupled Polyethylene Pipe and fittings Melt Flow Index IS:2530
1280 Quick Coupled Polyethylene Pipe and fittings Ovality IS:14151(Part-1)
Laboratory Name :

performed used
MECHANICAL- PLASTICS Pressure Bearing Capacity of
AND PLASTIC PRODUCTS holding Attachment
1282 Quick Coupled Polyethylene Pipe and fittings Reversion Test IS:14151(Part-1)
MECHANICAL- PLASTICS Rubber Ring Shore hardness
AND PLASTIC PRODUCTS (shore-A)
1284 Quick Coupled Polyethylene Pipe and fittings Tensile Strength IS:14151(Part-1)
1285 Quick Coupled Polyethylene Pipe and fittings Visual Appearance IS:14151(Part-1)
1286 Quick Coupled Polyethylene Pipe and fittings Wall Thickness IS:14151(Part-1)
MECHANICAL- PLASTICS Wall Thickness of HDPE
AND PLASTIC PRODUCTS Coupler
MECHANICAL- PLASTICS Weld ability test Acceptance &
1289 Quick Coupled Polyethylene Pipe and fittings Workmanship & Appearance IS:14151(Part-2)
MECHANICAL- PLASTICS Compression Set at constant
1290 Rubber & Rubber Product IS:3400 (Part-10)
AND PLASTIC PRODUCTS strain
1291 Rubber & Rubber Product Density IS:3400(Part-9)
1292 Rubber & Rubber Product Elongation at break ( %) IS:3400(Part-1)
1293 Rubber & Rubber Product Hardness Shore A IS:3400(Part-23)
1294 Rubber & Rubber Products Tensile Strength IS:3400(Part-1)
Dimension of integral sockets
MECHANICAL- PLASTICS Structural wall plastic piping systems for non pressure
1295 and spigot ends ( Wall IS:16098(Part-1)
AND PLASTIC PRODUCTS drainage and sewerage
Thickness of socket)
MECHANICAL- PLASTICS Structural wall plastic piping systems for non pressure Dimension of Pipe Fitting
1296 IS:16098(Part-1)
AND PLASTIC PRODUCTS drainage and sewerage (Mean outside Diameter)
Dimension of sockets and
MECHANICAL- PLASTICS Structural wall plastic piping systems for non pressure spigot ends for sliding socket
1297 IS:16098(Part-1)
AND PLASTIC PRODUCTS drainage and sewerage joints (Mean outside diameter
of sockets )
Laboratory Name :

performed used
Dimension of sockets and
MECHANICAL- PLASTICS Structural wall plastic piping systems for non pressure spigot ends for sliding socket
1298 IS:16098(Part-1)
AND PLASTIC PRODUCTS drainage and sewerage joints (Socket length spigot
end )
1299 Length IS:16098(Part-1)
1300 Wall Thickness IS:16098(Part-1)
MECHANICAL- PLASTICS Structured Wall plastic piping system for non pressure
1301 Reversion Test IS:12235 (Part-5)
MECHANICAL- PLASTICS Structured wall plastic piping systems for non pressure
1302 Appearance IS:16098(Part-1)
1303 Colour IS:16098(Part-1)
MECHANICAL- PLASTICS Structured wall plastic piping systems for non pressure Effect of heating (Stress Relief
1304 IS:12235(Part-6)
AND PLASTIC PRODUCTS drainage and sewerage Test )
Physical Characteristics of
1305 fitting (Appearance and colour IS:16098(Part-1)
)
1306 Resistance to Dichloromethane IS:12235(Part-11)
MECHANICAL- PLASTICS Structured wall plastic piping systems for non pressure Resistance to external blows at
1307 IS:12235(Part-9
AND PLASTIC PRODUCTS drainage and sewerage degree C
1309 Unplasticized PVC Pipe for water supplies Diameter At any point IS:12235
1310 Unplasticized PVC Pipe for water supplies Mean outside Diameter IS:12235
1311 Unplasticized PVC Pipe for water supplies Wall Thickness IS:12235(Part-1)
1312 Unplasticized PVC Pipe for water supplies Colour IS:4985
1313 Unplasticized PVC Pipe for water supplies Density IS:12235(Part-14)
MECHANICAL- PLASTICS Hydraulic Characteristic - Type
1314 Unplasticized PVC Pipe for water supplies IS:12235 (Part-8/S-1)
AND PLASTIC PRODUCTS Test
1315 Unplasticized PVC Pipe for water supplies IS:12235(Part-8/S-1)
Laboratory Name :

performed used
1316 Unplasticized PVC Pipe for water supplies Length IS:12235(Part-1)
1317 Unplasticized PVC Pipe for water supplies Length of Sockets IS:4985
MECHANICAL- PLASTICS Mean socket internal diameter
1318 Unplasticized PVC Pipe for water supplies IS:4985
AND PLASTIC PRODUCTS at mid point
1319 Unplasticized PVC Pipe for water supplies Opacity IS:12235(Part-3)
1320 Unplasticized PVC Pipe for water supplies Pipe End IS:4985
MECHANICAL- PLASTICS Resistance to external blows at
1321 Unplasticized PVC Pipe for water supplies IS:4985(Annexure-C)
AND PLASTIC PRODUCTS 0degree C
1322 Unplasticized PVC Pipe for water supplies Reversion Test IS:12235(Part-5)
1323 Unplasticized PVC Pipe for water supplies Sulphated Ash Content Test IS:4985(Annexure-B)
1324 Unplasticized PVC Pipe for water supplies Vicat Softening Temperature IS:12235(Part-2)
1325 Unplasticized PVC Pipe for water supplies Visual Appearance IS:4985
Unplasticized Polyvinyl Chloride (Pipes for soil and waste
MECHANICAL- PLASTICS Axial Shrinkage for type b pipe
1326 discharge system for inside and outside buildings including IS:13592(Annexure B)
AND PLASTIC PRODUCTS only
ventilation and drain water system
1327 discharge system for inside and outside buildings including Colour of pipe IS:13592
1328 discharge system for inside and outside buildings including Effect of sunlight IS:12235(Part-13)
MECHANICAL- PLASTICS Mean outside diameter at any
1329 discharge system for inside and outside buildings including IS:13592
AND PLASTIC PRODUCTS point
1330 discharge system for inside and outside buildings including Outside Diameter IS:13592
MECHANICAL- PLASTICS Resistance to blows at 0
1331 discharge system for inside and outside buildings including IS:4985 (Annexure-C)
AND PLASTIC PRODUCTS degree C
Laboratory Name :

performed used
MECHANICAL- PLASTICS Resistance to dichloromethane
1332 discharge system for inside and outside buildings including IS:12235(Part-11)
AND PLASTIC PRODUCTS at specified Temperature
1333 discharge system for inside and outside buildings including Resistance to Sulphuric Acid IS:12235(Part-7)
1334 discharge system for inside and outside buildings including Reversion Test IS:12235(Part-5)
1335 discharge system for inside and outside buildings including Stress Relief Test IS:12235(Part-6)
1336 discharge system for inside and outside buildings including Tensile Strength IS:12235(Part-13)
1337 discharge system for inside and outside buildings including Vicat Softening Temperature IS:12235(Part-2)
1338 discharge system for inside and outside buildings including Visual Appearance IS:13592
1339 discharge system for inside and outside buildings including Wall Thickness IS:13592
1340 discharge system for inside and outside buildings including Water Tightness of joints IS:13592
MECHANICAL- PLASTICS Unplasticized Polyvinyl chloride screen and casing pipes for
1341 Colour IS:12818
AND PLASTIC PRODUCTS bore /tube wells
1343 Dimension (Outside Diameter) IS:12235(Part-1)
MECHANICAL- PLASTICS Unplasticized Polyvinyl chloride screen and casing pipes for Elastomeric sealing ring
1344 IS :5382
AND PLASTIC PRODUCTS bore /tube wells hardness , Shore A
1345 Length of pipe IS:12818
MECHANICAL- PLASTICS Unplasticized Polyvinyl chloride screen and casing pipes for Mean outside diameter at any
1346 IS:12235(Part-1)
AND PLASTIC PRODUCTS bore /tube wells point
Laboratory Name :

performed used
MECHANICAL- PLASTICS Unplasticized Polyvinyl chloride screen and casing pipes for Resistance to external blows at
1347 IS:12235(Part-9)
AND PLASTIC PRODUCTS bore /tube wells 0 degree
MECHANICAL- PLASTICS Unplasticized Polyvinyl chloride screen and casing pipes for Threading of screen and casing
1349 IS:12818
AND PLASTIC PRODUCTS bore /tube wells pipe
MECHANICAL- PLASTICS Unplasticized Polyvinyl chloride screen and casing pipes for Threading of screen and casing
1350 IS:554
AND PLASTIC PRODUCTS bore /tube wells pipe
1353 Wall Thickness IS:12235(Part-1)
MECHANICAL- PLASTICS Dimension (Mean Outside
1354 Unplasticized PVC Pipe for water supplies IS:12235 (Part-1)
AND PLASTIC PRODUCTS Diameter)
MECHANICAL- PLASTICS UPVC Injection moulded fitting for soil & waste discharge
1355 Colour IS:14735
AND PLASTIC PRODUCTS system
1356 Dimension - Wall Thickness IS:12235(Part-1)
1357 Dimension - Wall Thickness IS:14735
1358 Dimension of pipe Clip IS:14735
1359 Dimension of vent cowl IS:14735
1360 Impact Test (Drop Test) is:14735 (Annex -C)
1361 Resistance to sulphuric Acid IS:12235(Part-7)
Socket Dimension /Socket
MECHANICAL- PLASTICS UPVC Injection moulded fitting for soil & waste discharge dimension for ring seal fitting
1362 IS:14735
AND PLASTIC PRODUCTS system (Mean inside diameter of
socket at midpoint )
MECHANICAL- PLASTICS UPVC Injection moulded fitting for soil & waste discharge dimension for ring seal fitting
1363 IS:14735
AND PLASTIC PRODUCTS system (Mean outside diameter of
spigot Portion )
Laboratory Name :

performed used
1364 dimension for ring seal fitting IS:14735
(Socket Depth)
1365 Stress Relief Test IS:12235(Part-6)
1366 Sulphated Ash Content IS:14735 (Annex-B)
1367 Vicat softening temperature IS:12235(Part-5)
1369 Water Tightness of joints IS:14735 (Annex-D)
1370 Workmanship IS:14735
MECHANICAL- SOIL AND
1371 Bentonite Fineness by Dry and Wet IS 6186 , Annex-A-6
ROCK
1372 Bentonite Gel Formation Index IS 6186, Annex-A-6
ROCK
1373 Bentonite Liquid Limit IS:2720(Part-5)
ROCK
1374 Bentonite Marsh cone viscosity ASTM D 6910
ROCK
1375 Bentonite Moisture Content IS 6186, Annex-A-6
ROCK
1376 Bentonite Sand Content IS 6186, Annex-A-9
ROCK
1377 Bentonite Swelling Power IS 6186, Annex-A-5
ROCK
1378 Granite Apparent Porosity IS:1124
ROCK
1379 Granite Compressive strength IS 1121(P-1)
ROCK
1380 Granite Dimension- Length IS 14223(P-1)
ROCK
1381 Granite Dimension- Thickness IS 14223(P-1)
ROCK
Laboratory Name :

performed used
1382 Granite Dimension- Width IS 14223(P-1)
ROCK
1383 Granite Dry Density IS:13030
ROCK
1384 Granite Hardness IS 13630(P-13)
ROCK
1385 Granite Moisture Content IS 13030
ROCK
1386 Granite Resistance to wear IS 1706
ROCK
1387 Granite Specific Gravity IS 1124
ROCK
1388 Granite Water Absorption IS 1124
ROCK
1389 Marble Dimension- Length IS 1130
ROCK
1390 Marble Dimension- Thickness IS 1130
ROCK
1391 Marble Dimension- Width IS 1130
ROCK
1392 Marble Hardness IS 13630(P-13)
ROCK
1393 Marble Moisture absorption IS 1124
ROCK
1394 Marble Specific Gravity IS 1122
ROCK
1395 Natural Building Stones Dimension- Length ATRL/WI/MECH/GEN/006
ROCK
1396 Natural Building Stones Dimension- Thickness ATRL/WI/MECH/GEN/006
ROCK
1397 Natural Building Stones Dimension- Width ATRL/WI/MECH/GEN/006
ROCK
1398 Natural Building Stones Durability IS 1126
ROCK
1399 Natural Building Stones Resistance to wear IS 1706
ROCK
1400 Natural Building Stones Specific Gravity IS 1124
ROCK
Laboratory Name :

performed used
1401 Natural Building Stones Transverse strength IS 1121(P-2)
ROCK
1402 Natural Building Stones Water absorption IS 1124
ROCK
1403 MECHANICAL- SOIL- BASIC Soil CBR IS 2720 (P-16)
Direct Shear Test (Angle of
1404 MECHANICAL- SOIL- BASIC Soil IS:2720(Part-13)
Friction )
Direct Shear Test (Cohesion
1405 MECHANICAL- SOIL- BASIC Soil IS: 2720(Part-13)
Test )
1406 MECHANICAL- SOIL- BASIC Soil Free Swell Index IS 2720 (P-40)
Grain Size Analysis (Wet and
1407 MECHANICAL- SOIL- BASIC Soil IS 2720(P-4)
dry sieve analysis)
1408 MECHANICAL- SOIL- BASIC Soil Liquid Limit IS 2720 (P-5)
1409 MECHANICAL- SOIL- BASIC Soil MDD (Heavy Compaction) IS 2720 (P-8)
1410 MECHANICAL- SOIL- BASIC Soil MDD (Light Compaction) IS 2720 (P-7)
1411 MECHANICAL- SOIL- BASIC Soil OMC (Heavy Compaction) IS 2720 (P-8)
1412 MECHANICAL- SOIL- BASIC Soil OMC (Light Compaction) IS 2720(P-7)
1413 MECHANICAL- SOIL- BASIC Soil Plastic Limit IS 2720(P-5)
1414 MECHANICAL- SOIL- BASIC Soil Specific Gravity IS 2720 (P-3/Sec-1)
1415 MECHANICAL- SOIL- BASIC Soil Water Content IS 2720 (P-2)
MECHANICAL- WOOD AND
1416 Block Board Adhesion of Plies IS 1659, Annex-H
WOOD PRODUCTS
1417 Block Board Dimension- Length IS 1659
WOOD PRODUCTS
1418 Block Board Edge Straightness IS 1659, Annex-D (Amd-1)
WOOD PRODUCTS
1419 Block Board Resistance to Water IS 1659, Annex-G
WOOD PRODUCTS
1420 Block Board Spot Test IS 1659, Annex-K
WOOD PRODUCTS
1421 Block Board Squareness IS 1659, Annex-D (Amd-1)
WOOD PRODUCTS

1422 Block Board Thickness IS 1659, Annex-E
WOOD PRODUCTS
1423 Block Board Width IS 1659
WOOD PRODUCTS
Laboratory Name :

performed used
1424 Plywood Adhesion of Plies IS 1734(P-5)
WOOD PRODUCTS
1425 Plywood Dimension -(Length) IS 303
WOOD PRODUCTS
1426 Plywood Dimension (Thickness) IS:303
WOOD PRODUCTS
1427 Plywood Dimension(width) IS:303
WOOD PRODUCTS
1428 Plywood Moisture Content IS 1734 (P-1)
WOOD PRODUCTS
1429 Plywood Water Resistance IS 1734 (P-6)
WOOD PRODUCTS
1430 PLywood for Concrete Shuttering Works Adhesion of Plies IS 1734 Part-5
WOOD PRODUCTS
1431 PLywood for Concrete Shuttering Works Dimension- Thickness IS 4990
WOOD PRODUCTS
1432 PLywood for Concrete Shuttering Works Dimensions- Length IS 4990
WOOD PRODUCTS
1433 PLywood for Concrete Shuttering Works Dimension-Width IS 4990
WOOD PRODUCTS
1434 PLywood for Concrete Shuttering Works Edge Straightness IS 4990, Annex-C
WOOD PRODUCTS
1435 PLywood for Concrete Shuttering Works Glue Shear Strength IS 1734 Part-4
WOOD PRODUCTS
1436 PLywood for Concrete Shuttering Works Modulus of Rupture IS 1734 Part-11
WOOD PRODUCTS
1437 PLywood for Concrete Shuttering Works Moisture Content IS 1734 Part-1
WOOD PRODUCTS
1438 PLywood for Concrete Shuttering Works Resistance to Water IS 1734 Part-6
WOOD PRODUCTS
1439 PLywood for Concrete Shuttering Works Squareness IS 4990, Annex-C
WOOD PRODUCTS
1440 Prelaminated Particle Boards form Wood Crack Resistance IS 12823, Annex-E
WOOD PRODUCTS
1441 Prelaminated Particle Boards form Wood Density IS 2380(P-3)
WOOD PRODUCTS
1442 Prelaminated Particle Boards form Wood Moisture IS 2380(P-3)
WOOD PRODUCTS
Laboratory Name :

performed used
1443 Prelaminated Particle Boards form Wood Resistance to Cigarette Burn IS 12823, Annex-F
WOOD PRODUCTS
1444 Prelaminated Particle Boards form Wood Resistance to Steam IS 12823
WOOD PRODUCTS
1445 Prelaminated Particle Boards form Wood Water Absorption IS 2380(P-16)
WOOD PRODUCTS
1446 Timber/Wood Moisture Content IS 1708(P-1)
WOOD PRODUCTS
1447 Timber/Wood Specific Gravity IS 1708(P-2)
WOOD PRODUCTS
NON-DESTRUCTIVE-
BUILDING MATERIALS -
1448 Hardened Concrete Depth of carbonation IS:516(Part-5/Sec-3))
REINFORCED CONCRETE
STRUCTURES
Magnetic Particle Testing-
NON-DESTRUCTIVE- ASME Section V: Article 7 and
1449 Ferro-magnetic material (Yoke, Fluorescent- Oil/water
METALS & ALLOYS 25, SE 709
base, Wet Dry)
NON-DESTRUCTIVE- Liquid Penetration Testing-
1450 Ferrous and Non- ferrous material ASTM E1417
METALS & ALLOYS (Solvent Removable)
NON-DESTRUCTIVE- Ferrous and Non- ferrous material (castings, Forgings and Ultrasonic Testing (Manual
1451 ASME Section V (Article 5)
METALS & ALLOYS Rolled materials) Contact Method)
NON-DESTRUCTIVE- Ultrasonic Testing (Manual
1452 Ferrous and Non- ferrous material (Weldments) ASME Section V (Article 4)
METALS & ALLOYS Contact Method)
1453 Ferrous material (Castings) ASTM A609
1454 Ferrous material (Forgings) ASTM A388
1455 Ferrous material (Forgings) IS 11626
1456 Ferrous material (Plates) ASTM A578
Laboratory Name :

performed used
Site Facility
Dry Density of soil (By core
1 MECHANICAL- SOIL- FIELD Soil IS:2720(Part-29)
cutter Method )
Dry Density of Soil (By Sand
2 MECHANICAL- SOIL- FIELD Soil IS 2720(P-28)
replacement method)
3 MECHANICAL- SOIL- FIELD Soil Electrical Resistivity of Soil IS 3043
NON-DESTRUCTIVE-
BUILDING MATERIALS - Low Strain Pile Integrity Test of
4 Concrete ASTM D 5882
REINFORCED CONCRETE Deep Foundations
STRUCTURES
NON-DESTRUCTIVE-
5 Hardened Concrete Concrete Resistivity BS EN 12390 Part-19
REINFORCED CONCRETE
STRUCTURES
NON-DESTRUCTIVE-
BUILDING MATERIALS - Crack Depth by Ultrasonic
6 Hardened Concrete IS:516(Part-5/Sec-1)
REINFORCED CONCRETE Pulse Velocity
STRUCTURES
NON-DESTRUCTIVE-
7 Hardened Concrete Depth of carbonation IS:516(Part-5/Sec-3))
REINFORCED CONCRETE
STRUCTURES
NON-DESTRUCTIVE-
8 Hardened Concrete Rebound Hammer Test IS:516(Part-5/Sec-4))
REINFORCED CONCRETE
STRUCTURES
NON-DESTRUCTIVE-
9 Hardened Concrete Ultrasonic Pulse Velocity Test IS:516(Part-5/Sec-1)
REINFORCED CONCRETE
STRUCTURES
NON-DESTRUCTIVE-
Intergrity Testing of Concrete
10 IN-Situ Concrete Pile Deep Foundations by ASTM D6760
REINFORCED CONCRETE
Ultrasonic Crosshole Testing
STRUCTURES
NON-DESTRUCTIVE-
BUILDING MATERIALS - Half cell potentials of Uncoated
11 Reinforced Concrete Structure ASTM C876
REINFORCED CONCRETE Reinforcing Steel in Concrete
STRUCTURES
NON-DESTRUCTIVE-
BUILDING MATERIALS - Half cell potentials of Uncoated
12 Reinforced Concrete Structure IS:516(Part-5/Sec-2))
REINFORCED CONCRETE Reinforcing Steel in Concrete
STRUCTURES
Laboratory Name :

performed used
NON-DESTRUCTIVE-
BUILDING MATERIALS - Protective Layer Thickness/
13 Reinforced Concrete Structure BS:1881(Part-204)
REINFORCED CONCRETE Cover
STRUCTURES
NON-DESTRUCTIVE-
14 Reinforced Concrete Structure Rebar Diameter BS:1881(Part-204)
REINFORCED CONCRETE
STRUCTURES
Magnetic Particle Testing-
NON-DESTRUCTIVE- ASME Section V: Article 7 and
15 Ferro-magnetic material (Yoke, Fluorescent- Oil/water
METALS & ALLOYS 25, SE 709
base, Wet Dry)
NON-DESTRUCTIVE- Liquid Penetration Testing-
16 Ferrous and Non- ferrous material ASTM E1417
METALS & ALLOYS (Solvent Removable)
NON-DESTRUCTIVE- Ferrous and Non- ferrous material (castings, Forgings and Ultrasonic Testing (Manual
17 ASME Section V (Article 5)
METALS & ALLOYS Rolled materials) Contact Method)
18 Ferrous and Non- ferrous material (Weldments) ASME Section V (Article 4)
19 Ferrous material (Castings) ASTM A609
20 Ferrous material (Forgings) ASTM A388
21 Ferrous material (Forgings) IS 11626
22 Ferrous material (Plates) ASTM A578
NOTE- The Laboratory has demonstrated competence for the stated scope for WATER. This however does not fully cover the
specification requirements of BIS for the Packaged Drinking Water as per IS 14543 and the Packaged Natural Mineral Water
IS 13428.

Scope TC 8006

Uploaded by

Copyright:

Available Formats

Scope TC 8006

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Scope TC 8006

Uploaded by

Copyright:

Available Formats

AADCO TESTING & RESEARCH LABORATORY PVT. LTD.

, F 28, BULANDSHAHAR ROAD

Component, parameter or Test Method Speciﬁcation

Component, parameter or Test Method Speciﬁcation

Component, parameter or Test Method Speciﬁcation

Component, parameter or Test Method Speciﬁcation

Component, parameter or Test Method Speciﬁcation

Component, parameter or Test Method Speciﬁcation

Component, parameter or Test Method Speciﬁcation

Component, parameter or Test Method Speciﬁcation

Component, parameter or Test Method Speciﬁcation

Component, parameter or Test Method Speciﬁcation

Component, parameter or Test Method Speciﬁcation

Component, parameter or Test Method Speciﬁcation

Component, parameter or Test Method Speciﬁcation

Component, parameter or Test Method Speciﬁcation

Component, parameter or Test Method Speciﬁcation

Component, parameter or Test Method Speciﬁcation

Component, parameter or Test Method Speciﬁcation

Component, parameter or Test Method Speciﬁcation

Component, parameter or Test Method Speciﬁcation

Component, parameter or Test Method Speciﬁcation

Component, parameter or Test Method Speciﬁcation

Component, parameter or Test Method Speciﬁcation

Component, parameter or Test Method Speciﬁcation

Component, parameter or Test Method Speciﬁcation

Component, parameter or Test Method Speciﬁcation

Component, parameter or Test Method Speciﬁcation

Component, parameter or Test Method Speciﬁcation

Component, parameter or Test Method Speciﬁcation

Component, parameter or Test Method Speciﬁcation

Component, parameter or Test Method Speciﬁcation

Component, parameter or Test Method Speciﬁcation

Component, parameter or Test Method Speciﬁcation

Component, parameter or Test Method Speciﬁcation

Component, parameter or Test Method Speciﬁcation

Component, parameter or Test Method Speciﬁcation

Component, parameter or Test Method Speciﬁcation

Component, parameter or Test Method Speciﬁcation

Component, parameter or Test Method Speciﬁcation

Component, parameter or Test Method Speciﬁcation

Component, parameter or Test Method Speciﬁcation

Component, parameter or Test Method Speciﬁcation

Component, parameter or Test Method Speciﬁcation

Component, parameter or Test Method Speciﬁcation

Component, parameter or Test Method Speciﬁcation

Component, parameter or Test Method Speciﬁcation

Component, parameter or Test Method Speciﬁcation

Component, parameter or Test Method Speciﬁcation

Component, parameter or Test Method Speciﬁcation

Component, parameter or Test Method Speciﬁcation

Component, parameter or Test Method Speciﬁcation

Component, parameter or Test Method Speciﬁcation

Component, parameter or Test Method Speciﬁcation

Component, parameter or Test Method Speciﬁcation

Component, parameter or Test Method Speciﬁcation

Component, parameter or Test Method Speciﬁcation

Component, parameter or Test Method Speciﬁcation

Component, parameter or Test Method Speciﬁcation

Component, parameter or Test Method Speciﬁcation