Rabbit Hutch Plans
Rabbit Hutch Plans
Rabbit Hutch Plans
com
Legal:
The content of this guide may not be sold, modified, or distributed in anyway without the expressed
written consent of the publisher. Reprinting, copying, or any other form of distribution for commercial
or non-commercial purposes is strictly prohibited and will be prosecuted.
Disclaimer:
Every attempt has been made to provide the most accurate information as possible. However, the
publisher accepts no liability for any wrong information as a result of purchasing and / or reading this
guide.
You can follow this guide at your own risk the publisher accepts no responsibility for any injury to any
person.
Copyright © www.Construct101.com
ISBN-13:
ISBN-10:
Shopping List
4 – 2×4 – 8′ 2 1/2″ deck screws
7 – 2×2 – 8′ 1 1/2″ deck screws
1 – 5/8″ t1-11 exterior siding – 4’x8′ fence staples
wire mesh hinges
door latch
Cutting List
2 – 2×4 – 47 1/2″ 2 – 2×4 – 47 1/2″
3 – 2×4 – 21″ 3 – 2×4 – 21″
4 – 2×4 – 18″ 4 – 2×4 – 18″
2 – 2×4 – 29 1/8″ 2 – 2×4 – 29 1/8″
4 – 2×2 – 18″ 4 – 2×2 – 18″
3 – 2×2 – 24″ 3 – 2×2 – 24″
3 – 2×2 – 32″ 3 – 2×2 – 32″
3 – 2×2 – 21″ 3 – 2×2 – 21″
Build the floor for the rabbit hutch, cut two 2×4’s to 47 1/2″ and three 2×4’s to 21″. Drill pilot holes and
assemble the floor as shown on illustration above using 2 1/2″ deck screws.
Cut the legs to the height you want the rabbit hutch or as shown above.
Cut four 2×4’s to 18″ and four 2×2’s to 18″, assemble the leg pieces to form a L, next drill pilot holes and
secure them together with 2 1/2″ deck screws. Attach the legs to the corners of the floor by drilling pilot
holes and using 2 1/2″ deck screws.
Build three wall frames as show on illustration above. Cut three 2×2’s to 24″ long, three 2×2’s to 32″
long, three 2×2’s to 21″ long, cut a 10 degree angle cut to one end, and three 2×2’s to 17″ long, cut a 10
degree angle cut to one end.
Assemble the wall frames as shown on illustration above, drill pilot holes and assemble with 2 1/2″ deck
screws.
Two of the wall frames will have 5/8″ t1-11 exterior siding, cut siding to size and install using 1 1/2″ deck
screws. Cut a door to one of the walls, see illustration above.
One of the wall frame will have wire mesh, cut to size and install using fence staples.
Install the walls, drill pilot holes and screw 2 1/2″ deck screws through the bottom wall frame and into
the floor.
Cut a 2×4 to 29 1/8″ long, make a 10 degree bevel cut to one edge of the board. Cut a 2×2 to 13 1/4″
long, make a bevel cut to one edge of the board. Install as shown on illustration above, drill pilot holes
and use 2 1/2″ deck screws.
Cut two 2×2’s to 13 1/4″ long, make a 10 degree bevel cut to the edge of one of the 2×2 boards. Cut a
2×4 to 29 1/8″ long, make a bevel cut to one edge of the board. Drill pilot holes and install with 2 1/2″
deck screws.
Cut wire mesh to size and install to the back as shown on illustration above. Cut the back siding to size,
notch around the 2×2’s, install using 1 1/2″ deck screws.
Cut two 2×2’s to 29 1/8″ long, and two 2×2’s to 17 1/2″ long. Assemble the door frame as shown on
illustration above, drill pilot holes and assemble with 2 1/2″ deck screws. Cut wire mesh to size and
attach to the door frame.
Cut two 2×2’s to 19″ long. and two 2×2’s to 13 1/4″ long. Assemble the door frame as shown on
illustration above, drill pilot holes and use 2 1/2″ deck screws to assemble. Cut siding to size and attach
to the door frame, screw 1 1/2″ deck screws through the siding and into the door frame.
Install the door hinges and attach the doors to the rabbit hutch. Install the door latch.
Cut a piece of siding to 32″ x 47 1/2″ for the roof. Attach the roof with 1 1/2″ deck screws, screw
through the siding and into the wall frame.