Amm215wtd 1887840
Amm215wtd 1887840
Amm215wtd 1887840
Serial Number
ENGLISH
WARNING
CAUTION
NOTE
Revision Control
Document number
PP-120312
2 User’s Guide
TABLE OF CONTENTS
ENGLISH
Please check the following items are present when you unpack the box, and save
the packing materials in case you will need to ship or transport the monitor in future.
• AMM215WTD LCD Monitor(the equipment that displays information,
graphic data, image and video on its LCD screen) and two video cables
(1) HD15 VGA cable (1) DVI-D cable
• AC Power cord*
• AC-Adapter CAUTION
Model No : JMW1100KB1300F02
ADVAN Int’l Corp accepts full responsibility for the effects on safety, reliability, and
performance of the equipment only if:
• Re-adjustments, modifications, and/or repairs are carried out exclusively
by ADVAN Int’l Corp.
• The electrical installation of the relevant operating room complies with the
applicable IEC and CE requirements.
The ADVAN Int’l Corp AMM215WTD monitor has been tested under UL 60601-1
standard and UL listed for Medical application.
ADVAN Int’l Corp reserves the right to make improvements in the product(s)
described herein. Product(s), therefore, may not agree in detail to the published
design or specifications. All specifications are subject to change without notice.
Please contact ADVAN Int’l Corp directly or phone your local ADVAN Int’l Corp sales
representative or agent for information on changes and new products.
AMM215WTD 5
Warnings
ENGLISH
1. Read the operating manual thoroughly and be familiar with its contents prior to using
this equipment.
2. Carefully unpack the unit and check if any damage occurred during shipment.
3. Should any solid object or liquid fall into the panel, unplug the unit and have it checked
by qualified personnel before operating it any further.
4. Uplug the unit if it is not to be used for an extended period of time. To disconnect the
cord, pull it out by the plug. Never pull the cord itself.
5. Be a qualified physician, having complete knowledge of the use of this equipment.
6. Test this equipment prior to a medical procedure. This monitor was fully tested at the
factory before shipment.
7. Avoid removing covers on control unit to avoid electric shock.
8. Attempt no internal repairs or adjustments not specifically detailed in this operating
manual.
9. Pay close attention to the care, cleaning instructions in this manual. A deviation may
cause damage (refer to the Cleaning section).
10. DO NOT STERILIZE MONITOR.
11. Read the entire instruction manual before assembling or connecting the camera.
12. Do not place the monitor or any other heavy object on the power cord. Damage to the
cable can cause fire or electirc shock.
13. Monitor with power supply is suitable for use in patient environment.
14. DO NOT stack more than 3 boxes high
This equipment has been tested and found to comply with the limits for medical devices in
IEC 601-1-2:2003. These limits are designed to provide reasonable protection against harm-
ful interference in a typical medical installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to other devic-
es in the vicinity. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to other devices, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving device.
- Increase the separation between the equipment.
- Connect the equipment into an outlet on a circuit different from that to which the other
device(s) are connected.
- Consult the manufacturer or field service technician for help.
NOTICES TO USER
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference, and (2) this device must accept any inter-
ference received, including interference that may cause undesired operation.
FCC WARNING
This equipement generates or uses radio frequency energy. Changes or modifications not
expressly approved by the party responsible for compliance could void the user’s authority
to operate the equipment. The user could lose the authority to operate this equipment if an
unauthorized change or modification is made.
6 User’s Guide
Cautions
1. The AC Adapter must be plugged into a Grounded power outlet.
2. Use only the proprietary AMM215WTD power supply for the
AMM215WTD monitor. Make a proper connection by ensuring that the
shrink tubing completely secures the connection between the DC power cord and the
extension cord.
3. Turn power off when unit is not in use.
4. Never operate the unit right after having transported from a cold location directly to a
warm location.
5. Do not expose the monitor to moisture or directly apply liquid cleaners directly to the
screen. Spray the cleaning solution into a soft cloth and clean gently.
6. Handle the monitor with care. Do not strike or scratch the screen.
7. Do not block the monitor cooling vents. The monitor is cooled by natural convection
and has no fan.
8. Do not force the monitor past 28 degrees of vertical when adjusting the screen
position. (For monitors equipped with stands only.)
9. Remove the power module and connection when transporting the unit.
10. Save the original carton and associated packing material. They will be useful should
you have to transport or ship the unit.
11. Allow adequate air circulation to prevent internal heat buildup.
12. Do not place the unit on surfaces (rugs, blankets, etc.) or near materials (curtains,
draperies) that may block the ventilation slots.
13. Do not install the unit near sunlight, excessive dust, mechanical vibration or shock.
14. The unit is designed for operation in a horizontal position. Never operate the unit in
a vertical position.
15. Keep the unit away from equipment with strong magnets (i.e. a large loudspeaker.)
16. Do not expose the monitor to moisture or excessive dust.
17. Equipment with SIP/SOP connectors should either comply with IEC 60601-1 and/or
IEC 60601-1-1 harmonized national standard or the combination should be evaluated.
Do not touch the patient with signal input or output connectors.
18. Use only a hospital grade power supply cord.
19. This equipment has been tested and found to comply with the limit for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable generate uses and can radiate radio frequency energy, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in
a particular installation, which can be detemined by turing the equipment off and on,
the user is encourage to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving device.
• Increase the separation distance between the equipment.
• Connect the equipment to an outlet on a circuit different from that to which the
other device(s) are connected.
• Consult the manufacturer or field service technican for help.
20. Grounding reliability can only be achieved when the equipment is connected to an
equipment receptacle labeled “Hospital Only” or “Hospital Grade.”
Note To connect to an international power supply, use a an attachment plug
appropriate for the power outlet.
Note Refer to the “Electromagnetic Compatibility” (EMC) section of this manual to
ensure EMC. The AMM215WTD must be installed and operated
according to the EMC information provided in this manual.
AMM215WTD 7
Symbol Definitions
ENGLISH
Dangerous: High Voltage Indicates protective earth
ground.
Date of Manufacture
8 User’s Guide
EU Declaration of Conformity for Medical Applications
After you unpack the monitor, make sure the following items are in-
cluded
CAUTION : AC adapter
Model No: JMW1100KB1300F02
ENGLISH
· Avoid placing the monitor, or any other heavy object, on the power cord
to prevent fire or electrical shock from damage to the power cord.
· Do not expose the monitor to rain, excessive moisture, or dust to avoid
fire or shock hazard.
· Do not cover the slots or openings of the monitor for proper heat
dissipation. Always put the monitor in a place where there is adequate
ventilation.
· Avoid placing the monitor against a bright background or where sunlight
or other light sources may reflect on the area of the monitor. Place the
monitor just below eye level.
· Handle with care when transporting the monitor.
· Refrain from giving the shock or scratch to the screen, as screen is
fragile.
To clean the screen, do not spray liquid cleaners directly on to the unit. Stand away
Form the monitor and spray cleaning solution onto a cloth. Without applying exces-
sive pressure, clean the screen with the slightly dampened rag.
On Burn-in
Permanent burn-in may occur from the followings:
• Displaying color bar or static images repeately or for a long period of time.
• Using the unit repeatedly in a high temperature/ high humidity environment
• Displaying an image smaller than the monitor continuously.
To reduce the risk of burn- in, we recommend turning off the power of the unit, and
reducing the brightness when the unit is not in use.
10 User’s Guide
POWER MANAGEMENT FUNCTION
The monitor is equipped with the power management function which automatically
reduce the power consumption when not in use in three power level modes.
• Stand-by Mode
The monitor goes into stand-by mode when the horizontal sync signal is off for
about 10 seconds. In this mode, the screen goes off and the power LED blinks
for 1 seconds On and 1 second Off. The screen is displayed after the horizontal
sync signal is restored.
• Suspend Mode
The monitor goes into suspend mode when the vertical sync signal is off for
about 10 seconds. The power consumption during this is 27 W. In this mode,
the screen goes off and the power LED blinks for 1 seconds On and 1 second
Off. The screen is displayed after the vertical sync signal is restored.
• Off Mode
The monitor goes into power-off mode when the vertical and horizontal sync
signals are off for about 10 seconds. In this mode, the screen goes off and the
power LED blinks for 1 seconds On and 1 second Off. The screen is displayed
after the vertical and horizontal sync signals are restored.
Power
45W TBD TBD TBD
Consumption
When the monitor is power saving mode or detects an incorrect timing, the screen
will be blank and power LED indicator will blink.
AMM215WTD 11
PRESET MODES
ENGLISH
DVI and VGA input signal formats
Horizontal Vertical
Pixel clock
Resolution frequency frequency
( MHz )
( KHz ) ( Hz )
Component
Format DVI 1/2 VGA C-Video Y/C SDI RGB+ RGB+
Y/Pb/Pr
CS HV
NTSC *1 O O
PAL *2 O O
480/59.94i O O O O O
480/59.94p O O O
576/50i O O O O O
576/50p O O O O O
720/50p O O O O O O
720/59.94p O O O O O O
720/60p O O O O O O
1080/23.98psf O O O O
1080/24psf O O O O
1080/23.98p O O O O O
1080/24p O O O O O
1080/25p O O O O O O
1080/29.97p O O O O O O
1080/30p O O O O O O
1080/50i O O O O O O
1080/59.94i O O O O O O
1080/60i O O O O O O
1080/50p O O O *3
1080/60P O O O *3
*1 NTSC-M, NTSC-433
*2 PAL-BDGHI, PAL-M, PAL-N, PAL-60
*3 3G-SDI signal
AMM215WTD 13
PIP / POP / PBP function
ENGLISH
The following combination options are available to you:
DVI 1 O O O O O
DVI 2 O O O O O
SDI O O O O
Component/
O O O O O
RGBs
VGA O O O O O
Y/C O O O O
C-VIDEO O O O O
14 User’s Guide
DDC
To make your installation easier, the monitor is able to Plug and Play with your
system if your system also supports DDC protocol. The DDC (Display Data
Channel) is a communication protocol through which the monitor automatically
informs the host system about its capabilities, for example, supported resolutions
and corresponding timing. The monitor supports DDC1 and DDC2B standard.
INSTALLATION
To install the monitor to your host system, please follow the steps as given below:
Steps
1. Use the supplied video cable (DVI, VGA, S-Video, C-Video) then connect to the
host system accordingly.
2. Connect the DC power to the DC power connector on the monitor.
3. Connect one end of AC power cord into the AC Adapter and the other end to AC
power outlet.
4. Then turn the host system on and then the monitor.
5. If the monitor still does not function properly, please refer to the troubleshooting
section to diagnose the problem.
IN
OUT
SDI IN SDI OUT C - Video S - Video RGB / Component
AMM215WTD 15
CONNECTING the POWER CORD
ENGLISH
*
for your area.
* This monitor has an universal AC adapter that allows operation in either
AC 100 - 240 V ac voltage area. No user-adjustment is required.
* Plug one end of the power cord to the AC adapter, plug another end to a proper
AC outlet.
The cord set should have the appropriate safety approvals for the country in which
the equipment will be installed and marked HAR.
For 120 volt Applications, use only UL Listed deachable power cord with NEMA
Power Supply
Model No: JMW1100KB1300F02
AMM215WTD
16 User’s Guide
User Functions / Messages
Rocker Switch
ENGLISH
Main Menu
Chromatic
Gamma Change the gamma value - 1.8, 1.9, 1.95, 2.1, 2.1S, 2.2, 2.3,
2.4, 2.4S, S0, Radio graph
Visual
ENGLISH
Setting
Scale Mode Change the scale mode - Fill all, One to One,
Vertical - fill, Horizontal - fill, Fill aspect ratio
ENGLISH
Sub menu of POP
Mode POP Mode ON / Off
Advanced
Restore Factory Changes the all OSD value to factory outgoing status
ENGLISH
Sub menu of OSD Control
H-position Adjust OSD H - position (Range 0 - 100)
OSD Time out Adjust OSD time out - 5s, 10s, 15s, 20s, 1m, 2m
Information
Input Format Display the current input resolution and vertical frequency
ENGLISH
Before sending your LCD monitor for servicing, please check the troubleshooting
list below to see if you can self-diagnose the problem.
ENGLISH
: Direct Current
MEDICAL EQUIPMENT
WITH RESPECT TO ELECTRIC SHOCK,
FIRE AND MECHANICAL HAZARDS ONLY : UL approval mark according to the
IN ACCORDANCE WITH UL 60601-1, AND safety standard for Medical equipment
51LJ CAN/CSA C22.2 NO. 601.1
Medical Equipment
E215822
This monitor is intended for use in Health Care Facilities model AMM215WTD
Equipment is not suitable for use in the presence of flammable anesthetic mixture
with air or with oxygen or nitrous oxide.
No user serviceable parts inside, ask qualified personnel when accessing inside.
Classification
This monitor has been tested to comply with IEC/EN 60601-1, IEC/EN60601-1-2
and is certified by UL to medical standard UL60601-1(UL/cUL Mark).
Because many medical offices are located in residential areas, this monitor, in ad-
dition to the medical requirements, has also been tested and found to comply with
the limits for FCC Class B computing devices in a typically configured system. It is
the system integrator or configurer’s responsibility to test and ensure that the entire
system complies with applicable EMC laws.
The Model AMM215WTD is intended for use in the electromagnetic environment specified below.
The customer or the user of AMM215WTD should assure that it is used in such an environment.
Electromagnetic
Immunity Test IEC 60601 Test Level Compliance Level environment - guidance
ENGLISH
Power frequency netic fields should be
(50/60Hz) mag- at levels characteristic
3.0 A/m 3.0 A/m
netic field of a typical location in
IEC 61000-4-8 a typical commercial or
hospital environment.
Note: Ut is the A.C. mains voltage prior to application of the test level.
NOTE 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and
reflection from structures, objects, and people.
(a) Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones and land mobile
radios, amateur radio, AM and FM radio broadcast and TV broadcast, connot be predicted theoretically with accuracy.
To assess the electromagnetic environment due to fixed RF transmitters, an electromagnetic site survey should be
considered. If the measured field strength in the location in which the AMM215WTD is used exceeds the applicable RF
compliance level above, the AMM215WTD should be observed to verify normal operation. If abnormal performance is
observed, additional measures may be necessary, such as reorienting or relocating the AMM215WTD.
(b) Over the frequency range 150kHz to 80MHz, field strengths should be less than [V1] V/m.
30 User’s Guide
For transmitters rated at a maximum output power not listed above, the recommended separation distance (d) in me-
ters (m) can be estimated using the equation applicable to the frequency of the transmitter, where P is the maximum
output power rating of the transmitter in watts (W) according to the transmitter manufacturer.
NOTE 1: At 80 MHz and 800 MHz, the separation distance for the higher frequency range applies.
NOTE 2: These guidelines may not apply in all situations. Electromagnetic propagation is affected by absorption and
reflection from structures, objects, and people.
ENGLISH
Rocker Switch
32 User’s Guide
Connectors
DC Input
Connector Jack Power Input
Pin Description Pin Description
1 GND 4 NC
3 13 V Input
Video Input
24 pin DVI-I connector.
DDWG or equivalent connector.
Pin Description Pin Description Pin Description
4 NC 12 NC 20 NC
5 NC 13 NC 21 NC
S - Video connector.
Pin Description Pin Description
1 GND 5 GND
2 GND 6 GND
3 CHROMA_IN 7 CHROMA_OUT
4 LUMA_IN 8 LUMA_OUT
C - Video connector.
Pin Description Pin Description
2 GND 4 GND
AMM215WTD 33
Description of Warranty
ENGLISH
ADVAN warrants to the first Buyer (Buyer) that the product purchased when
shipped in its original container will conform to ADVAN specifications, and to any
ADVAN approved specifications furnished to ADVAN by the Buyer, and will be
free of defects in materials and workmanship. ADVAN warrants that the product
purchased is manufactured from new components which meet ADVAN standards,
quality and specifications.
Subject to the conditions and limitations set forth below, ADVAN will, at its option,
either repair any component of its products that prove defective by reason of
improper workmanship or materials or ADVAN has the exclusive right to replace
with refurbished units or with an equivalent product. ADVAN warrants that the
components used for repair, refurbished units or equivalent product will meet
ADVAN standards, quality and specifications.
LCD panels and touch screens are warranted for a period of twelve (12) months
from the date of shipment.
Protection filters are not warranted as damage to the protection filter is considered
to be normal wear and tear and can be replaced at Buyer’s cost.
Limitation of Warranty
This limited warranty does not cover any damage to this product or other non-
ADVAN products that results from any of the following: improper installation
or operation; accident; abuse; misuse; natural disaster; war; insufficient or
excessive electrical supply; abnormal mechanical or environmental conditions; any
unauthorized disassembly, repair or modification; normal wear and tear; tampering
by anyone other than an ADVAN engineer or an ADVAN Authorized Service Center
(ASC); the use of supplies, consumable items and conditions beyond the control
of ADVAN, such as common carrier provided equipment and/or facilities; operation
of ADVAN product in excess of the specifications. This limited warranty also does
not apply to any product that has not been handled or packaged correctly, that has
been sold as second-hand or has been resold contrary to the US export regulations,
on which the original identification information (i.e. serial number, rating and/or
warranty label) has been altered, obliterated or removed.
34 User’s Guide
Return Material Authorization (RMA) Procedure
All claims must be submitted through the ADVAN website, whether in warranty
or out, first Buyer, distributor or OEM. End Users who have purchased through a
distributor or OEM, please contact the distributor or OEM.
http://www.advancorprma.com
In-transit damage is not covered by warranty. ADVAN will only pay for the return
shipment by surface transportation.
For product support, please e-mail details of your inquiry including product model:
service@advancorp.com
In Warranty
ADVAN or its ASC will repair or replace if defective in material or workmanship
without cost, for a period of eighteen (18) months, (LCD panels and touch screens
for a period of twelve (12) months) after the date of shipment.
Buyer must notify ADVAN or its ASC of the defect before expiration of the warranty
period, and request an RMA number. If the configuration has been modified in
any manner, the product must be returned to its original configuration before any
warranty service will be performed by ADVAN or its ASC. No goods are to be
returned to ADVAN or its ASC without prior authorization. Buyer will be responsible
for packaging (preferably original container) and shipping the defective goods to
ADVAN or its ASC, shipping charges prepaid.
ADVAN or its ASC will return the in warranty product, at no cost to the buyer.
AMM215WTD 35
Out-of-Warranty
ADVAN or its ASC will repair or replace if defective in material or workmanship with
ENGLISH
fee, any product which the warranty period has expired (out-of-warranty).
Buyer must notify ADVAN or its ASC of the defect and request an RMA number. If
the configuration has been modified in any manner, the product must be returned to
its original configuration before any service will be performed by ADVAN or its ASC.
No goods are to be returned to ADVAN or its ASC without prior authorization. Buyer
will be responsible for packaging (preferably original container) and shipping the
defective goods to ADVAN or its ASC, shipping charges prepaid.
ADVAN or its ASC will return the out-of-warranty product, at cost to the buyer.
THE LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU
MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE OR
JURISDICTION TO JURISDICTION.
Authorized Representative in Europe
EIZO GmbH, Display Technologies
Siemensallee 84,
D-76187 Karlsruhe, Germany
Tel: +49 721 20321 0
Fax: +49 721 20321 474
Web Page : http://www.Eizo.eu