Mygig Lockpick Pro Instructions
Mygig Lockpick Pro Instructions
Mygig Lockpick Pro Instructions
REV
IN 2
AUDIO MULTIMEDIA
IN AUDIO AND VIDEO
INPUTS TO, DVD,
VIDEO
IN GAME, SAT TV, ETC.
PRESS TO TOGGLE TO
REVERSE CAM VIDEO INPUT
(FACTORY OR AFTERMARKET)
CONTROLS ON BACK
OF STEERING WHEEL
CAM OFF
This manual will document in detail, the many functions of the LOCKPICK PRO and how to properly
set the programming switches to your desired operation. Installation diagrams are included to guide you in
various connection strategies. Please read this manual fully so that you can learn to take advantage of all of
the exciting features and capabilities of the new MYGIG LOCKPICK PRO.
At this time, Coastal Electronic Technologies, Inc. would like to recommend that you have this
installation completed by a certified mechanic or someone familiar with automotive electronics. This
installation, while not time consuming, does require careful attention to detail and precise following
of installation instructions.
Coastal Electronic Technologies, Inc. accepts no responsibility due to the improper installation or
use of this product. Installation and / or use of this product implies and signifies user acceptance of
this term of use. Please adhere to all driving laws in your state.
OK, let’s get started. On your MYGIG LOCKPICK PRO control box are switch settings which allow you to program your Lockpick for your
vehicle and the features you would like to enable. The diagrams below are important to enable the MYGIG module to work with MYGIG radio
systems. More than one switch may be turned on at a time to create the feature list you desire. Place switches in the desired configuration before
plugging in the module. Improper switch settings will not damage anything however it could cause your radio to fail to turn on or conflict with
existing accessories.
NOT NOT
COMMUNICATION
TYPE USED USED
LOCKPICK PRO
**CHECK APPLICATION
GUIDE
Camera Options
1. With access to the rear of the screen, unplug the matching GRAY and WHITE (if present)
connector(s) and plug them into the female connectors of your MYGIG LOCKPICK PRO harness. Then
plug the male connectors of the LOCKPICK harness into the earlier factory locations. The connectors
are keyed and cannot be plugged in to the wrong location. Line up the connectors carefully and make
sure that no pins are bent or misaligned before pressing hard to make sure the connector is fully seated.
2. Even if your radio did not have a white connector plugged in from the factory, make sure and plug
the White connector into the location shown above. Failing to plug in the WHITE connector will
cause the radio to display a blank screen when the Lockpick camera functions are activated.
3. Make sure the Dip Switch and Vehicle Select Dial settings for your Lockpick are configured properly
before plugging the controller into the harness. If you plug in the controller and then change switch
settings, the new settings will not be programmed and improper operation will result.
4. 2008-2009 (some 2010) vehicles with factory rear view cameras are powered only while the vehicles is
in Reverse. If you would like to enable full control and viewing of your FACTORY REAR VIEW
CAMERA while in DRIVE or other gears, the included REVERSE CAMERA POWER output wire
must be connected as the power source for your camera. This 12V power output will turn on when
the vehicle is placed in reverse and also when selected by the user using the radio buttons.
If you choose not to connect the REVERSE CAMERA POWER wire provided by the Lockpick
harness to your factory rear camera, the rear camera view will continue working while in reverse.
However, because the rear camera will have no power in other gears, it cannot be activated by the
Lockpick and will display as a blank or flashing picture if activated manually while in Drive.
If your installation requires the use of the REVERSE CAMERA POWER Lockpick wire to
enable factory camera operation in all gears, it is simply a matter of running a wire to the factory
camera and connecting it in place of the original power wire. Remove any panels covering the rear
hatch in your vehicle. Then use a meter or indicator lamp to determine the reverse power connection
on the factory camera connector. Make sure you are measuring directly on the connector at the
camera location and not further back in a different location. This wire will switch to 12V while the
vehicle is in REVERSE and will be zero at other times. Cut this wire and connect the REVERSE
CAM 12V+ power connection from the Lockpick to the camera directly. Do not reconnect the
original camera power source wire or fail to cut the wire at the camera. Instead tape it up and
disregard it. The Lockpick will provide all necessary power and timing for the factory camera.
Failing to cut the wire or connecting the Lockpick power and factory power at the same time could
cause the reverse tail light to illuminate at improper times. Also, cutting the wire at a different
location other than directly on the camera connector could possibly interrupt power to other
functions such as the actual reverse taillights or rear obstacle detection systems.
5. If you do not currently have a rear view camera and want to add one to your vehicle, the Lockpick
makes it easy. A REVERSE CAM 12V + power output and Ground connections is provided on the
Lockpick harness for your aftermarket rear camera. The Lockpick harness is equipped with a rear
camera video input to make your installation simple.
6. If you would like to add a Rear Cargo/Bed camera to your vehicle, connect the Cargo Cam’s power
to the REVERSE CAM 12V + power output and also to the ground provided on the Lockpick
Harness. Plug in the Cargo Cam video to the Second Reverse/Cargo video input connection provided
on the Lockpick harness. It is OK to connect rear and cargo camera power to the same Lockpick
camera power output if installing multiple rear view cameras. The Lockpick can show this camera
on demand or automatically instead of your standard rear camera when pulling a trailer, etc.
7. If you want to add a front camera, side cameras or all three at once, Connect your camera powers to
the Lockpick harness output labeled ADDITIONAL CAM POWER 12V+ and connect all grounds to
the GROUND provided on the Lockpick harness. Connect the video from your cameras to the RCA
video inputs labeled on your Lockpick module. Place Option Dip Switch 5 DOWN if installing
simultaneous front, rear, left and right cameras to enable special programming for this option.
8. Also present on your Lockpick harness is a 12V ACC output connection. This ACC output is created
by the Lockpick and can be used as a convenient 12V switched power source for many of your
accessories. It is rated for a constant 1.5 AMPs and will automatically turn on and off at the proper
times of your vehicle use. If your power needs are greater than 1.5 Amps, you may use the
CONSTANT 12V output conveniently provided by the Lockpick harness and switch it on and off
through a relay powered by the ACC power output of the Lockpick harness.
**NOTE: The connections for 12V Constant Battery power (YELLOW), ACC Ignition power (RED), GROUND
(BLACK), Reverse/Cargo power (ORANGE W/STRIPE), Front/Baby cam power (RED W/STRIPE), are
provided as a BONUS in your wiring harness for you to use when connecting additional accessories such as a
DVD player, Game, Cameras, Radar detector, etc., without worry that they might drain your battery when the
car is turned off. The ACC wire can power up to 1.5 Amps constant. Higher loads should be connected with a
relay.
** Do not attach the Constant or ACC wires directly to the vehicle wiring or ignition switch. The
Lockpick is plug and play for standard DVD/AUX/NAV/VIDEO/AUDIO/CAM unblocking and does
not require connections for power or ground. Connecting these Lockpick outputs to the vehicle wiring
can damage the unit and cause improper operations.
** When the MYGIG LOCPICK PRO is turned on for the first time, allow 30 seconds before
operating the various functions and features. This allows the Lockpick to prepare the radio and
screen views for standard operations. During the first startup, the Lockpick will create the SAT TV
mode and all touch screen options to begin your interface for use. The Lockpick will automatically
update the TV channels, requiring only a couple of seconds, each time the TV mode is selected.
During the time that “Updating Channels” or “Initializing” is displayed on the TV mode screen, the
touch screen options are not available for selection.
MYGIG LOCKPICK PRO OPERATION INSTRUCTIONS
The MYGIG LOCKPICK PRO automatically activates the TV mode and generates up to
5 pages of touch screen options for simple user control. Touch the on-screen button to select
the desired function. **Mygig radio buttons and locations will vary with year and Mygig radio
model.
Within the the MYGIG LOCKPICK PRO options, the user can add the VES rear
entertainment mode to any MYGIG radio not already equipped. Video and audio INPUTS are
provided on the LOCKPICK PRO harness which can allow aftermarket multimedia systems
( DVD, Satellite, Streaming, etc.) to display their video on the MYGIG system screen and have the
audio play through the factory sound system WITHOUT FM modulators.
The Lockpick video and audio inputs are selected on the touch screen by pressing the VES
mode button created by the MYGIG LOCKPICK PRO. If the on-screen display does not show the
AUX input selections, press the VES MODES button at the bottom of the screen. The REAR AUX 1
input can then be selected by touching the onscreen AUX 1 button. This will activate the audio and
video inputs of the multimedia inputs on the Lockpick harness. If you are in PARK, the view video
button will be available in the lower right corner of the screen for front screen video viewing of
your AUX input. The LOCKPICK PRO can allow the view video button to be automatically
enabled even if you switch to DRIVE or, if the AUTO OVERRIDE is disabled, it can be enabled
manually by pressing the power button 2x.
The A/V OUTPUTS on the LOCKPICK PRO harness can output the MYGIG DVD video and
audio directly to a rear screen system. The MYGIG radio is capable of DUAL ZONE operation.
• This means it can output one set of audio or audio/video to the rear system while allowing
the front operator to view or listen to something else on the MYGIG radio itself.
• The system cannot output the A/V inputs from the LOCKPICK PRO harness to the A/V
outputs on the harness at the same time.
• The MYGIG radio can output the video from the internal DVD player to the rear system
while simultaneously viewing and listening to either the AUX input audio and video
provided on the LOCKPICK PRO harness or any of the standard functions of AM, FM,
SAT or hard drive. You can also send just the audio from the AM, FM, SAT, or hard drive
out to the rear seat entertainment system.
To select which audio and video source you would like to send out of the A/V output of the
LOCKPICK PROharness, press the menu button and then select the onscreen button for REAR
VES.
• The screen will then show the possible options for outputting MYGIG radio and video
• Select the source 1 tab and not the source 2 tab
• Any option for output is available on the radio or media tabs. The VES output options are
not selectable as they are applicable only to a factory VES system. If you would like to send
out the picture and the sound from a DVD playing in the MYGIG radio to your additional
screen, select the MEDIA tab and then the DISC option. The DVD in your MYGIG radio
will continue to play and output its audio and video to your rear seat system even if you then
switch to any of the different functions available on the MYGIG radio for the front seat
operator.
Installation Q & A:
1. I installed the Lockpick and now my radio does not turn on.
Check all interface controls and switches. Insure that vehicle select is set for (0) and that option switches 1
and 2 are correctly set for the vehicle type (see application chart). Check to make sure you have installed
the Gray and White connectors behind the radio and that all pins were straight before fully inserting the
connectors.
2. When I put the car in Reverse, the radio screen blanks out. I do not have a rear view camera.
The Lockpick automatically activates a rear view camera input for your radio. If you do not intend to
install a rear view camera or do not want it activated automatically, refer to page 2 of the Lockpick options
in the TV mode to disable the AUTO REAR function.
4. I installed the Lockpick and now my factory VES rear entertainment is intermitting.
The Lockpick is able to create a VES mode within your radio to allow a multimedia audio and video input
as well as an output for additional screen(s) if desired. The default setting on page 4 of the Lockpick
options is VES OFF. If you change the option and turn it ON when you already have a factory VES system,
the communication will conflict. Set the option to OFF to restore factory VES operation.
5. My radio does not have a VIDEO button viewable at any time. Will the Lockpick work for this car?
The Lockpick will enable the video function regardless of whether it is currently dealer activated.
6. I do not have a navigation radio or my radio is a new RHB navigation radio. Will the Lockpick turn on the
Uconnect and voice recognition functions?
No, these radios do not have the hardware internally to receive Bluetooth or provide support for voice
recognition. The Lockpick will remove the error message saying the feature is not active when the
Uconnect button is pressed so that it can be used for Lockpick PRO operations. Follow the initialization
procedure described earlier.
7. I turned on one of the Camera or VES AUX input functions created by the Lockpick and all I see is a flashing
picture or blank screen when I try to look at the video.
This means you don’t have anything connected or, do not have the camera turned on to supply a video
input. The radio screen will be blank or flash when there is no video from your connected device. Common
solutions for camera pictures are normally resolved by rechecking the power connections and insuring that
all cameras are powered by the connections provided on the Lockpick harness. This includes the factory
rear view camera, if your vehicle requires a Lockpick connection to power it while in a gear other than
reverse. Also, check to make sure you have fully inserted the White connector on the Lockpick harness
and the video connections for your device are plugged in. Connectors not fully inserted may create
intermitting operations.
8. I turned on my car for the first time after installing the Lockpick and I do not have any of the menus in the
SAT TV mode as shown in the illustrations.
The first time the Lockpick is powered on, it will wait 30 seconds before loading the menus for Lockpick
operations in the SAT TV mode. After this initialization, the menus will be loaded and present when the
radio is turned on. The Lockpick will also refresh the menus each time the SAT TV mode is selected.
During the couple of seconds that the menus are reloaded, the touch screen options are not available for
selection.
The Lockpick PRO Option switch 5 can be placed DOWN to allow the user to install a rear
camera along with front and side mounted turn signal activated cameras – all at the same time.
This key feature of the PRO line allows full 360° camera placement while the Lockpick controls
automatic activation or manual viewing of each camera. The diagram on the last page details the
input locations on the Lockpick module and cable for proper operations in this special mode. Plug
the cameras into the locations shown and connect camera power to the Lockpick harness. Make
sure that the Lockpick module is unplugged before Option switch 5 is placed in the DOWN position
for this option to be activated. Allow 30 seconds after the radio is turned on to load the new menu
choices to your radio.
TO LOCKPICK BLACK GROUND WIRE
AFTERMARKET
REVERSE CAM POWER
REVERSE
UNPLUG ORIGINAL RADIO TO LOCKPICK ORANGE W/BLACK
STRIPE WIRE CAMERA
CONNECTORS THEN PLUG IN HERE
REV CAM VIDEO CONNECT HERE
PLUG AND PLAY
NO OTHER CONNECTIONS ARE REV
IN
NECESSARY FOR OVERRIDE FEATURES
FACTORY CONNECTORS TO LOCKPICK BLACK GROUND WIRE
FRONT CAM POWER AFTERMARKET
INCLUDED TO LOCKPICK RED W/BLACK FRONT
STRIPE WIRE CAMERA
FRONT CAM VIDEO CONNECT HERE
REV
IN 2
AUDIO MULTIMEDIA
IN AUDIO AND VIDEO
INPUTS TO, DVD,
VIDEO
GAME, SAT TV, ETC.
SPECIAL LOCKPICK PRO INSTALL IN