Philips ds8550 Ver.1.4 Docking Speaker
Philips ds8550 Ver.1.4 Docking Speaker
Philips ds8550 Ver.1.4 Docking Speaker
TABLE OF CONTENTS
Page
Circuit diagram.......................................................6-1..6-4
Layout diagram......................................................6-5..6-7
©
Copyright 2010 Philips Consumer Electronics B.V. Eindhoven, The Netherlands
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or
transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise without
the prior permission of Philips.
Published by LX 1052 Service Audio Printed in The Netherlands Subject to modification 3141 785 35454
Version 1.4
1-2
TECHNICAL SPECIFICATION
• Aux in
VERSION VARIATION
MEASUREMENT SETUP
Tuner FM
Bandpass
DUT 250Hz-15kHz LF Voltmeter
e.g. 7122 707 48001 e.g. PM2534
RF Generator
e.g. PM5326
Ri=50:
Use a bandpass filter to eliminate hum (50Hz, 100Hz) and disturbance from the pilottone (19kHz, 38kHz).
Tuner AM (MW,LW)
Bandpass
250Hz-15kHz LF Voltmeter
DUT e.g. 7122 707 48001 e.g. PM2534
RF Generator
e.g. PM5326
S/N and distortion meter
e.g. Sound Technology ST1700B
Ri=50:
Frame aerial
e.g. 7122 707 89001
To avoid atmospheric interference all AM-measurements have to be carried out in a Faraday´s cage.
Use a bandpass filter (or at least a high pass filter with 250Hz) to eliminate hum (50Hz, 100Hz).
CD Recorder
Use Audio Signal Disc SBC429 4822 397 30184 Use Universal Test Cassette CrO2 SBC419 4822 397 30069
(replaces test disc 3) or Universal Test Cassette Fe SBC420 4822 397 30071
DUT
DUT LF Generator L
L e.g. PM5110
R
R
S/N and distortion mete
S/N and distortion meter e.g. Sound Technology ST170
e.g. Sound Technology ST1700B
LEVEL METER
LEVEL METER e.g. Sennheiser UPM550
e.g. Sennheiser UPM550 with FF-filter
with FF-filter
1-4
SERVICE AIDS
GB WARNING ESD
All ICs and many other semi-conductors are
susceptible to electrostatic discharges (ESD).
Careless handling during repair can reduce life
drastically.
When repairing, make sure that you are
connected with the same potential as the mass
of the set via a wrist wrap with resistance.
Keep components and tools also at this
potential.
GB
Safety regulations require that the set be restored to its original CLASS 1
condition and that parts which are identical with those specified,
be used LASER PRODUCT
Safety components are marked by the symbol ! .
Lead free
2-1
2.1.4 Tabs
The battery tabs are not so stubborn especially for aluminum tab.
• Don’t bend tab
2.1.6 Short
Short terminals of battery is strictly prohibited, it may damage battery.
Caution
Danger of explosion if battery is incorrectly replaced.Replace only with the same or equivalent type.
3-1
BLOCK DIAGRAM
WIRING DIAGRAM
CN4 CN3
CN5
J9
CON1
IR BOARD
JACK1
CON3
MAIN BOARD
JACKE1
4-1
JACK BOARD
J10
CON6 CON8 J4
CON4
CON133
J2
KEY BOARD
iPod Docking Board
5-1 5-1
DISASSEMBLY DIAGRAM
BOTTOM CAB.
SPEAKER GRILL
FRONT CAB.
C
6-1 6-1
IR BOARD
JACK BOARD
EXPLODED VIEW