Home Articles Circuit Bench Mini Projects Bookstore Q&A

Search …  Search

Newest Component

Two-Stage FM Transmitter (TEL047E)

This high-power transmitter uses one transistor to produce the high-frequency signals and a second transistor to power an
amplifier stage. Using this configuration, the range is up to 2 miles in open field.

Features Latest
Power supply voltage: 6 to 12 Vdc
Abracon ABSES5AD AF Precision
Output power: 200 mW to 1 W Location SAW Filters

Paranormal Experiments with

This transmitter uses a power output stage to increase the high-frequency signal power. The output power rises to a few M5Stack U140 Solid State Relay
hundred milliwatts, which is enough to send signals to a receiver placed at distances up to two miles. Unit
Electronic Candle (PN068E)
The power supply used in this circuit must produce a large amount of current.
Molex Premo-Flex Superior
Therefore, it is recommended that you avoid the use of common cells in favor of supplies powered from the ac power line, a Retention Cable Jumpers
car battery, or nicad battery. If the circuit is powered from the ac power line, it is very important to use good filtering and
ams OSRAM OSLON® Compact
regulation to avoid noise and hum in the transmitted signals.
PM Generation 2
The main application suggested for this transmitter is as an experimental broadcast station for clubs, schools, or Laser Image Generator (PN048E)
campgrounds. The signals from a CD player, tape deck, computer, MP3 or microphone passing through a mixer can be
Raspberry Pi 5 Single Board
applied to the transmitter’s input to act as program sources.
Computer
The transistor is not an expensive type as would be recommended for high-power transmitters; rather, it is a common, low- The Ice That Gives Electric Shock
cost audio transistor that can oscillate in the FM range. The transistor’s low cost is an additional attraction for the reader (DID009E)
who doesn’t have much money to spend on a transmitter project.

Only two adjustments are needed to put this transmitter on the air, and building it does not require any special tools or
instruments.
Circuit Bench
Loudspeaker Overload Detector
How It Works
(CB384E)
The oscillator stage is formed by a BF494 or BF495 in the configuration seen in other projects in this site. This stage This old configuration, using a
produces a signal with a frequency determined by L1 and CV. The reader must tune this circuit to a free point in the FM band unijunction transistor (UJT)
between 88 and 108 MHz. controls a LED than blinks if an...

The feedback that keeps the oscillator on is given by C3, the capacitor wired between the transistor’s collector and emitter. Four Transistor Reflex Receiver
Resistors R1 and R2 bias the transistor’s base, and C2 decouples this electrode, applying high-frequency signals to ground (CB961E)
(passing through the power supply). This an old commercial receiver
found in a year 1958 magazine.
The audio signal is applied to the circuit via Cl as in many other circuits described in this site.
The circuit uses some
The audio signal’s amplitude must be controlled to avoid saturating the circuit, causing distortion. Audio signal sources can transformer...
be used, such as a mixer or sound console processing signals from sources such as tape decks, CD players, microphones,
etc. Q Multiplier (CIR916E)

PDFmyURL converts web pages and even full websites to PDF easily and quickly.
 The signal produced by this stage is applied to a power output stage using a BD135, BD137, or BD139. The BDs are audio, Factor Q measures the selectivirty
medium-power transistors, but they have a good gain when working with high-frequency signals. Their fT (transition of a resonant circuit and also
frequency) is about 150 MHz, which means that they can produce a good power gain when working with signals in the FM receivers. This circuits cen...
hand.

To get the best performance from this transistor, the configuration must be the so called “common base” one as shown in
Fig. 1.

Figure 1 – Common base stage

The base/emitter capacitance, which decreases the high-frequency gain, can be reduced if the transistor is wired in this
configuration. Of course, the power gain found in this configuration is not as high as in the common emitter configuration,
but the capacitance effects can be reduced.

Figure 2.shows what happens. Large gains at higher frequencies can be achieved if the transistor is used in the common
base configuration.

PDFmyURL converts web pages and even full websites to PDF easily and quickly.
 Figure 2 – Common base stages are used in high-frequency stages

The high-frequency modulated signal is applied to the amplifier stage by L2.

Observe that, to get the better performance when transferring the high-frequency signal from one stage to another, it is
necessary to adjust CV1 correctly.

Resistors R5 and R6 bias the output transistor, and C5 decouples its base.

The output signal appears on CV2/L3 and, from this resonant circuit, it can be transferred to the antenna.

The other necessary adjustment is to tune CV2 for best performance in signal transference. Capacitors C6 and C7 filter and
decouple the power supply voltage.

Assembly

The complete diagram of this transmitter is shown in Fig. 3.

PDFmyURL converts web pages and even full websites to PDF easily and quickly.
 Figure 3 –Schematics for the transmitter

The printed circuit board suggested for this project is shown in Fig. 4.

PDFmyURL converts web pages and even full websites to PDF easily and quickly.
 Figure 4 – Printed circuit board used in the project

L1/L2 and L3/L4 must be assembled one inside the other (interlaced) as shown in Fig.5.

PDFmyURL converts web pages and even full websites to PDF easily and quickly.
 Figure 5 – Wiring the coils

The coils are wound using AWG 18 to 22 enameled wire as shown in same figure.

L1 and L3 is formed by four turns, and L2 and L4 formed by three turns. The forms have a diameter between 0.6 and 0.8
mm. Small changes in these dimensions can be compensated by the trimmer adjustments.

The trimmer capacitors can range from 20 to 40 pF, and both plastic and porcelain types can be used. According to the
terminal layout found in these compo nents, the need to make small changes in the printed circuit layout must be
considered.

We recommend that the reader first buy the trimmer capacitors and see how their terminals are placed. Afterward, you can
work on the printed circuit board project and make etching alterations if necessary.

All capacitors except C6 are ceramic types (disc or plate). The electrolytic is rated to 16 WVDC or more.

The transistor can be a BD135, BD137, or BD139, and it must be mounted on a small heat sink. It is interesting to experiment
with several transistors to achieve the best gain. These transistors have a wide range of characteristics, and among many
apparently identical units it is possible to find one with higher gain.

For the audio signal input, you can use a jack that is appropriate for the signal source. If an electret microphone is used, a 10
k 9 resistor must be used for biasing as shown in Fig. 6.

PDFmyURL converts web pages and even full websites to PDF easily and quickly.
 Figure 6 – Using an electret microphone

The component values in parentheses (Fig. 3) are appropriate when using a 12 V power supply. A regulated power supply
for this circuit is shown in Fig. 7.

PDFmyURL converts web pages and even full websites to PDF easily and quickly.
 Figure 7 – Power supply for the transmitter

The transformer has a primary winding rated to 117 Vac and a secondary rated to 12 V (CT) X 1 A.

The electrolytic capacitors must be rated to 25 WVDC or more. The power-on LED indicator is optional.

Adjustments and Use

Tune any FM receiver to a free point of the FM range and place it 10 to 15 ft away from the transmitter. To the transmitter’s
output, wire a small 6 V x 50 mA incandescent lamp or a multimeter adjusted to the 0-5 Vdc scale as shown in Fig. 8.

PDFmyURL converts web pages and even full websites to PDF easily and quickly.
 Figure 8 – Using a lamp or multimeter for adjustments

First, tune CV1 until you can hear the signal in the receiver. Second, adjust CV2 to the highest output power (higher lamp
glow or higher voltage indicated by the multimeter). Readjust CV1 adjustments to keep the signal in the tuned point in the
receiver.

An external antenna, if installed, can be connected to the transmitter as shown in Fig. 9.

Figure 9 –Connecting to an external antenna

Using a field strength meter, adjust CV3 to get the best performance.

PDFmyURL converts web pages and even full websites to PDF easily and quickly.
 An FM receiver with an S-meter can be used for this purpose. A shielded cable must be used to connect the transmitter to
the antenna.

Semiconductors

Q1 - BF494 or BF495, NPN high-frequency (RF) transistors

Q2 - BD135, BD137, or ED 139, medium-power NPN silicon transistors

Resistors (1/8 W, 5%)

R1 - 10 k ohm - brown, black, orange

R2 - 6,800 ohm - blue, gray, red

R3 - 47 ohm -yellow, Violet, black (100 ohm x 1 W, brown, black, brown)

R4 - 22 ohm - red, red, black

R5 - 4,700 ohm - yellow, violet, red

R6 - 2,200 ohm - red, red, red

Capacitors

C1 - 1 µF metal film or ceramic

C2, C5 - 0.01 pF ceramic

C3 - 4.7 pF ceramic

C4 - 100 pF ceramic

C6 - 100 µF/ 16 WVDC electrolytic

PDFmyURL converts web pages and even full websites to PDF easily and quickly.
 C7 - 0.1 µF ceramic

CV1, CV2 - trimmer (see text)

Additional Parts and Materials

J 1 - microphone jack

L1, L2, L3, L4 - coils (see text)

Printed circuit board, power supply, plastic box, antenna terminals, heat sink to Q2, wires solder etc.

Datasheets

N° of component
OK

Institute Newton C. Braga - 2015 - 2023 ©

PDFmyURL converts web pages and even full websites to PDF easily and quickly.