Ovation E-910FC UM Rev14
Ovation E-910FC UM Rev14
Ovation E-910FC UM Rev14
Electrical warning. Not following these instructions may cause electrical damage to
the product, accessories, or the user.
Critical installation, configuration, or operation information. Not following these
! instructions may make the product not work, cause damage to the product, or cause
harm to the operator.
Important installation or configuration information. The product may not function
correctly if this information is not used.
Useful information.
The term “DMX” used throughout this manual refers to the USITT DMX512-A
digital data transmission protocol.
FCC Compliance
This device complies with Part 15 Part B of the FCC Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause
undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
Personal Safety
• Avoid direct eye exposure to the light source while the product is on.
• Always disconnect the product from the power source before cleaning or replacing the fuse.
• Always connect the product to a grounded circuit to avoid the risk of electrocution.
• Do not touch the product’s housing when operating because it may be very hot.
Mounting and Rigging
• This product is for indoor use only! Do not operate this product outdoors or in any location where
dust, excessive heat, water, or humidity may affect it (IP20).
• Do not leave any flammable material within 50 cm of this product while operating or connected to
power.
• CAUTION: When transferring product from extreme temperature environments, (e.g., cold truck to warm,
humid ballroom) condensation may form on the internal electronics of the product. To avoid causing a
failure, allow product to fully acclimate to the surrounding environment before connecting it to power.
• Mount this product in a location with adequate ventilation, at least 20 in (50 cm) from adjacent
surfaces.
• When hanging this product, always secure to a fastening device using a safety cable.
• Use only the hanging/mounting bracket to carry this product.
Power and Wiring
• Ensure that the power cord is not crimped or damaged.
• Always ensure that the product is connected to proper voltage in accordance with the specifications
in this manual or on the product’s specification label.
• Make sure to replace the fuse with another of the same type and rating.
• Never connect the product to a dimmer pack or rheostat.
• Never disconnect this product by pulling or tugging on the power cable.
Operation
• The luminaire should be positioned so that prolonged staring into the luminaire at a distance closer
than 2.3 m is not expected.
• If the external flexible cable or cord of this luminaire is damaged, it shall be replaced by a special
cord or cord exclusively available from the manufacturer or his service agent.
• The light source contained in this luminaire shall only be replaced by the manufacturer or his service
agent or a similar qualified person.
• The luminaire is intended for professional use only.
• Do not operate this product if there is damage on the housing, lenses, or cables. Have the damaged
parts replaced by an authorized technician at once.
• Do not cover the ventilation slots when operating to avoid internal overheating.
• The maximum ambient temperature is 113 °F (45 °C). Do not operate the product at higher temperatures.
• The minimum startup temperature is -4°F (-20°C). Do not start the product at lower temperatures.
• The minimum ambient temperature is -22°F (-30°C). Do not operate the product at lower temperatures.
• In the event of a serious operation problem, stop using this product immediately!
Features
• Operating modes:
• HSV: hue, saturation, value control
• 1-channel: dimmer
• 3-channel: dimmer, virtual color wheel, color temperature
• 5-channel: RGBAL control
• 7-channel: RGBAL control, dimmer, strobe
• 10-channel: RGBAL control, 16-bit dimmer, strobe, virtual color wheel, color temperature
• 12-channel: RGBAL control, dimmer, strobe, virtual control wheel, color temperature, auto
programs, auto speed, control
• 13-channel: 16-bit RGBAL and dimmer, strobe
• 16-channel: 16-bit RGBAL and dimmer, strobe, virtual color wheel, color temperature, control
• Full-color LED (RGBAL) ERS-style lighting product for theater, film, and production
• Ultra-smooth 16-bit dimming of master dimmer and individual colors
• Flat, even field of light with superior color mixing
• Virtual color wheel with color matched to popular gel colors
• Color temperature presets from 2800 K to 6500 K with high CRI and CQS
• RDM (Remote Device Management) for added flexibility
• Adjustable PWM (Pulse Width Modulation) to avoid flickering on camera
• Virtually silent operation for use in studio and theater applications
• Works perfectly with industry-standard lens tubes and accessories
25.910 in
283 mm
6.86 in 11.17 in
174 mm 283 mm
19.35 in
491 mm
19.15 in
486 mm
6.77 in
172 mm
AC Plug
The Ovation E-910FC comes with a power input cord terminated with a Neutrik® powerCON® connector
on one end and an Edison plug on the other end (U.S. market). If the power input cord that came with the
product has no plug, or if the plug needs to be changed, use the table below to wire the new plug.
Connection Wire (U.S.) Wire (Europe) Screw Color
AC Live Black Brown Yellow or Brass
AC Neutral White Blue Silver
AC Ground Green/Yellow Green/Yellow Green
Power Linking
The product supports power linking. It is possible to power link up to 7 products at 120 V, up to 13 products
at 208 V, up to 14 products at 230 V, or up to 15 products at 240 V. This product comes with a power input
cord. Power-linking cables are available for purchase from Chauvet.
Fuse Replacement
1. Disconnect this product from the power outlet.
2. Using a Phillips-head screwdriver, unscrew the fuse holder cap from the housing.
3. Remove the blown fuse and replace with another fuse of the same type and rating (T 3.15 A, 250 V).
4. Screw the fuse holder cap back in place and reconnect power.
Make sure to disconnect the product’s power cord before replacing a blown fuse.
! Always replace the blown fuse with another of the same type and rating.
DMX Linking
The Ovation E-910FC can be linked to a DMX controller using a 3- and 5-pin DMX connection. If using
other DMX-compatible products with this product, it is possible to control each individually with a single
DMX controller.
DMX Personalities
The Ovation E-910FC uses a 3- and 5-pin DMX data connection for the HSV, 1Ch, 3Ch, 5Ch, 7Ch, 10Ch,
12Ch, 13Ch, and 16Ch DMX personalities.
• Refer to the Introduction for a brief description of each DMX personality.
• Refer to the Operation chapter to learn how to configure the Ovation E-910FC to work in these
personalities.
• The DMX Values section provides detailed information regarding the DMX personalities.
For information about DMX standards, Master/Slave connectivity, or the DMX cables
needed to link this product to a DMX controller, download the DMX Primer from the
Chauvet website: www.chauvetprofessional.com.
Remote Device Management (RDM)
Remote Device Management, or RDM, is a standard for allowing DMX-enabled devices to communicate
bi-directionally along existing DMX cabling. Check with the manufacturer or the DMX controller’s User
Manual, as not all DMX controllers have this capability. The Ovation E-910FC supports RDM protocol that
allows feedback to make changes to menu map options.
Mounting clamp
Mounting bracket
Safety cable
Accessory Slot
The Ovation E-910FC has an accessory slot, which holds a drop-in iris, a motorized pattern device, or
various other optional accessories (sold separately).
1. Loosen the thumbscrews on the slot cover. (Note: Do not remove the thumbscrews).
2. Slide to cover forward.
3. Insert an accessory. (Note: Make sure to insert the accessory correctly. i.e., the iris handle
extends upward from the slot.
4. Slide the cover back. Make sure any handles or adjustment tools that stick out the top are able to
function correctly.
5. Tighten the thumbscrews to secure the cover.
Starting Address
In this mode, each product will respond to a unique starting address from the DMX controller. All products
with the same starting address will respond in unison.
1. Go to the DMX Address main level.
2. Set the starting address (001–512).
The highest recommended starting address for each DMX mode is as follows:
DMX Personality DMX Address DMX Personality DMX Address
HSV 510 10Ch 503
1Ch 512 12Ch 501
3Ch 510 13Ch 500
5Ch 508 16Ch 497
7Ch 506
Configuration (Standalone)
Use standalone configuration to operate the product without a DMX controller.
Focus Mode
Focus mode allows for focusing of the Ovation E-910FC without changing any menu settings.
1. Press and hold <ENTER> for 3 seconds. The intensity will increase to 100%.
2. Press <MENU> to exit to previous settings.
Virtual Color Wheel
1. Go to the Virtual Color Wheel main level.
2. Select Virtual Color Wheel.
3. Select the desired gel color (see Virtual Color Wheel Chart).
4. Select the desired output level (000–255).
Color Temperature
To select a color temperature, do the following:
1. Go to the Virtual Color Wheel main level.
2. Select Color Temperature.
3. Select the desired color temperature (see Color Temperature DMX Chart).
4. Select the desired output level (000–255).
Manual Color Mixer
To do color mixing without a DMX controller, follow the instructions below:
1. Go to the Virtual Color Wheel main level.
2. Select Manual Color Mixer.
3. Select the color to edit (Red, Green, Blue, Amber, or Lime Green).
4. Select the desired output level for that color (000–255).
5. Repeat steps 3 and 4 until product outputs as desired.
Auto Programs
Auto programs allow for dynamic RGBAL color mixing without a DMX controller.
1. Go to Auto Show main level.
2. Select the desired auto program (Auto 1–5).
3. Select the desired speed (1–100).
Red Shift
The Red Shift function causes the amber LEDs to imitate the appearance of a halogen lamp when dimming.
To adjust the Red Shift function, do the following:
1. Go to the Red Shift main level.
2. Select On or Off.
White Balance
This setting determines the maximum output values for each color, which affects the appearance of a full
output white.
1. Go to the White Balance main level.
2. Select Off (the product will use a default setting) or Manual.
3. For Manual mode, select the color value to edit (Red, Green, Blue, Amber, or Lime Green).
4. Set the maximum value for the selected color (125–255).
5. Repeat steps 3 and 4 until the product outputs as desired.
LED Frequency
This option changes the Pulse Width Modulation (PWM) frequency of the LEDs on the
Ovation E-910FC. To do so, follow the instructions below:
1. Go to the LED Frequency main level.
2. Select PWM Frequency (600Hz, 1200Hz, 2000Hz, 4000Hz, 6000Hz, or 25Khz).
Fan Mode
This setting determines how the fan speed on the Ovation E-910FC is set.
1. Go to the Fan Mode main level
2. Select Auto (fan speed will increase or decrease based on product temperature), Off (fan will
stay off. Product output will decrease based on product temperature), Silent (fan will maintain a
constant silent speed), or On (fan speed will always be at maximum).
NOTICE: When operating in Fan Mode: Off, the output of the fixture will be reduced
and will not reach the same levels as when using other fan modes.
WARNING: When operating in Fan Mode: Off, the fixture will become hotter to the
! touch than when using other fan modes. Use proper protective equipment to prevent
burns. Keep a safe distance from flammable objects.
Back Light
This setting allows for selection of the amount of time the backlight on the Ovation E-910FC’s display stays
on after the last button is pressed on the control panel.
1. Go to the Back Light main level.
2. Select 10S (10 seconds), 30S (30 seconds), 2Min (2 minutes), or Always On (remains on).
System Information
This option displays the total number of hours the product has run, the installed software version, and the
product’s UID.
1. Go to the Information main level.
2. Select Fixture Hours, LED Hours, Version, or UID.
HSV
Channel Function Value Percent/Setting
1 Hue 000 255 0–100%
2 Saturation 000 255 0–100%
3 Value 000 255 0–100%
UL 1573
R CSA C22.2 No. 166
E113093
Before sending the product, clearly write the following information on a piece of paper and place it inside
the box:
• Your name
• Your address
• Your phone number
• RMA number
• A brief description of the problem
Be sure to pack the product properly. Any shipping damage resulting from inadequate packaging will be
your responsibility. FedEx packing or double-boxing are recommended.
Chauvet reserves the right to use its own discretion to repair or replace returned
! product(s).
Contact Us
General Information Technical Support
Chauvet World Headquarters
Address: 5200 NW 108th Ave. Voice: (844) 393-7575
Sunrise, FL 33351 Fax: (954) 756-8015
Voice: (954) 577-4455 Email: chauvetcs@chauvetlighting.com
Fax: (954) 929-5560
Toll Free: (800) 762-1084 Website: www.chauvetprofessional.com
Chauvet U.K.
Address: Unit 1C Email: UKtech@chauvetlighting.eu
Brookhill Road Industrial Estate
Pinxton, Nottingham, UK Website: www.chauvetprofessional.eu
NG16 6NT
Voice: +44 (0) 1773 511115
Fax: +44 (0) 1773 511110
Chauvet Benelux
Address: Stokstraat 18 Email: BNLtech@chauvetlighting.eu
9770 Kruishoutem
Belgium Website: www.chauvetprofessional.eu
Voice: +32 9 388 93 97
Chauvet France
Address: 3, Rue Ampère Email: FRtech@chauvetlighting.fr
91380 Chilly-Mazarin
France Website: www.chauvetprofessional.eu
Voice: +33 1 78 85 33 59
Chauvet Germany
Address: Bruno-Bürgel-Str. 11 Email: DEtech@chauvetlighting.de
28759 Bremen
Germany Website: www.chauvetprofessional.eu
Voice: +49 421 62 60 20
Chauvet Mexico
Address: Av. de las Partidas 34 - 3B Email: servicio@chauvet.com.mx
(Entrance by Calle 2)
Zona Industrial Lerma Website: www.chauvetprofessional.mx
Lerma, Edo. de México, CP 52000
Voice: +52 (728) 690-2010
Visit the applicable website above to verify our contact information and instructions to request support.
Outside the U.S., U.K., Ireland, France, Germany, Benelux, or Mexico, contact the dealer of record.