MCD 115 Installation
MCD 115 Installation
MCD 115 Installation
SONOLINE Elegra
Ultrasound Imaging System
48 45 801 REV 00
Wiedergabe sowie Vervielfältigung dieser Unterlage, Verwertung und Mitteilung Copyright 2000 Siemens Medical Systems, Inc.
ihres Inhalts nicht gestattet, soweit nicht ausdrücklich zugestanden. Zuwieder- Proprietary data, company confidential. All rights reserved.
handlungen verpflichten zu Schadenersatz. Alle Rechte für den Fall der Patent- Confié à titre de secret d´entreprise. Tous droits réservés.
erteilung oder GM-Eintragung vorbehalten. Confiado como secreto industrial. Nos reservamos todos los derechos.
Go to Main TOC
SONOLINE Elegra Ultrasound Imaging System - Color Video Monitor MCD 115 Installation
Table of Contents
SONOLINE Elegra Ultrasound Imaging System - Color Video Monitor MCD 115 Installation
1.1 Introduction
This procedure describes the installation of Barco MCD 115 Color Video Monitor and the
CRT Arm Mounting on the SONOLINE Elegra ultrasound imaging system.
NOTICE Barco has provided a modified monitor that has a different power plug location. This monitor
requires an additional four to six inches of length in the power cable inside the monitor housing. If a
power cord extension is not provided cut the ties that secure the power cord, and then can relocate
the cord to provide the extra length needed to connect it to the monitor.
1.1.3 Preparation
! WARNING To avoid damage to the system and to the accessories caused by short circuit or injuries to
yourself caused by electric shock during installation, ensure that you have disconnected
the system power cable from the external main power source before you begin with the
installation.
2. Move the system if necessary to provide enough space for easy access during installation.
3. Lock the wheels to prevent the system from rolling during the installation.
SONOLINE Elegra Ultrasound Imaging System - Color Video Monitor MCD 115 Installation
1.1 ”Introduction”
1.2.2
1.2.1 ”Removing Monitors
”Removing Monitors with Single Cables”
with Short/Long
Cable Pairs”
1.2.3
”Removing the CRT Is the CRT Arm
Arm” Yes
Installation Kit
required?
1.2.4 1.2.3
”Removing the ”Removing the CRT
Covers” Arm” No
1.2.5 1.2.4
”Disconnecting the ”Removing the
Monitor Cables” Covers”
1.2.6
”Connecting the
Monitor Cables”
No Yes
1.2.7
”Replacing the Top
Frame”
1.2.8
”Installing the
Covers”
1.2.9 1.2.10
”Installing the CRT ”Installing the
Arm” Monitor”
1.3
”Operational Test”
SONOLINE Elegra Ultrasound Imaging System - Color Video Monitor MCD 115 Installation
1. Rotate the monitor arm away from the top to expose the bottom.
Bottom Monitor
Arm Cover
Screws
2. Remove the three screws from the bottom of the monitor arm to remove the top and
bottom covers (Figure 2).
• If short/long cable pairs are connected inside the monitor arm, follow the steps in
section 1.2.1, “Removing Monitors with Short/Long Cable Pairs.”
• If single cables are routed from the SONOLINE Elegra system through the monitor
arm into the monitor, follow the steps in section 1.2.2, ”Removing Monitors with
Single Cables” on page 6.
! WARNING The monitor weighs 65 lb. (29.5 kg). Take appropriate precautions when removing it from
the monitor arm.
1. With the monitor arm top and bottom covers already removed, disconnect the three
monitor cables.
2. Remove the monitor ground strap.
3. Remove four screws to detach the clamp ring from the monitor yoke. Remove the
monitor spacer, if applicable.
4. Carefully remove the monitor from the monitor arm and set it face down on a flat sur-
face.
5. Remove the monitor top cover (Figure 3).
6. Disconnect and remove the monitor cables from the monitor.
SONOLINE Elegra Ultrasound Imaging System - Color Video Monitor MCD 115 Installation
Top Monitor
Cover
Yoke
Bottom Monitor
Cover
! WARNING The monitor weighs 65 lbs (29.5 kg). Take appropriate precautions when removing it from
the monitor arm.
1. If you have yet to do so, remove the three screws from the bottom monitor arm to
remove the top and bottom monitor arm covers.
2. Remove the top cover from the monitor.
3. Disconnect the Video Display Cable, Power Cable, and Microphone Cable. Clip any
cable ties securing the cables.
4. Loosen the four screws securing the bottom monitor cover.
5. Pull the three cables out of the monitor through the monitor arm.
6. Remove the monitor ground strap.
7. Remove four screws to detach the clamp ring from the monitor arm. Remove the mon-
itor spacer in the yoke, if applicable.
8. Carefully remove the monitor from the monitor arm.
SONOLINE Elegra Ultrasound Imaging System - Color Video Monitor MCD 115 Installation
Microphone
Cable Connector
Ground Strap
Monitor Arm
Rear Handle
Monitor
Mounting Spindle Nut
Hole Cap (inside ring)
Lower CRT
Arm Spindle
(outside ring)
Right, Rear
Upper Cover
Right, Front
Upper Cover
SONOLINE Elegra Ultrasound Imaging System - Color Video Monitor MCD 115 Installation
NOTICE The access filter panel is attached to the rear vent panel by two Velcro strips. Remove the rear
vent panel carefully because you may accidentally loosen or jar the access filter panel.
Microphone Cable
1. Determine the cable route of the microphone cable to the Distribution Board.
2. Disconnect the microphone cable connector from J15 on the Distribution Board.
3. Cut all cable ties that fasten the Microphone Cable and remove the cable.
SONOLINE Elegra Ultrasound Imaging System - Color Video Monitor MCD 115 Installation
3. Cut all cable ties that fasten the Monitor AC Power Cable and remove the cable.
Distribution Board
with cables connected
NOTICE When routing the cables across the top of the system, lay the cables side by side. The top front
cover will not lay flat if the cables overlap each other.
2. Connect the monitor AC power cable to the power supply connector (J108).
3. Connect the microphone cable to J15 on the Distribution Board.
4. Connect the video display cable to J13 on the Distribution Board.
5. Use cable ties to attach all cabling to machine anchor points found along the cable
routes.
NOTICE There are 15 machine anchor points to which monitor cables must be anchored. Be sure to anchor
any additional cables whose cable ties were cut during the monitor cable removal procedure.
SONOLINE Elegra Ultrasound Imaging System - Color Video Monitor MCD 115 Installation
6. The monitor cables have a tendency to become pinched between the ground strap lug
and a screw. To solve this problem, install a cable tie within the swing arm directly blow
the monitor opening. The figure below illustrates the recommended solution.
Top Plate
Top Frame
SONOLINE Elegra Ultrasound Imaging System - Color Video Monitor MCD 115 Installation
NOTICE The access filter panel is attached to the rear vent panel by two Velcro strips. It may become loose
or jar free when you are installing the rear vent panel.
NOTICE Install the spindle with the raised detent positioned to the rear of the system.
SONOLINE Elegra Ultrasound Imaging System - Color Video Monitor MCD 115 Installation
NOTICE Position the tang on the lower clamp ring so that it faces the rear of the monitor.