User Manual WFQA1214EVJM
User Manual WFQA1214EVJM
User Manual WFQA1214EVJM
INSTALLATION GUIDE
SAFETY INFORMATION
1. The manufacturer reserves the right for any modifications
on the product which might be deemed necessary or
useful without informing about it in this IFU.
2. Before operating your new washing machine, please read
this instruction carefully, and keep it for future reference. If
you have lost it accidentally, ask customer service for e-
copy or hard copy.
3. Please make sure the socket is grounded securely, the
water source connection is reliable.
4. This appliance is not to be used by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction
concerning use of the appliance by a person responsible
for their safety.
5. This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or
instruction concerning use of the appliance in a safe way
and understand the hazards involved. Children shall not
play with the appliance. Cleaning and user maintenance
shall not be made by children without supervision.
6. Children should be supervised to ensure that they do not
play with the appliance.
7. If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified
persons in order to avoid a hazard.
8. The new hose-sets supplied with the appliance are to be
used and that old hose-sets should not be reused.
1
9. For appliances with ventilation openings in the base, that a
carpet must not obstruct the openings.
10. Children of less than 3 years should be kept away unless
continuously supervised.
11. The maximum permissible inlet water pressure, 1 MPa, for
appliances intended to be connected to the water mains.
The minimum permissible inlet water pressure, 0.1 MPa, if
this is necessary for the correct operation of the appliance.
12. The maximum washing capacity is 7/8/9/10/11/12kg.
13. For private domestic use only.
14.
2
ensure
Ensure
Ensure that the ventilation openings in the base of the washing machine
(if available on your model) are not obstructed by a carpet or other material.
3
that
ing
the
615 mm
855 mm
4
that
en the
,
the mains.
5
Clean the outside of the washing machine with a damp cloth. Do not use abrasive
detergents.
Never open the door forcibly or use it as a step.
6
BEFORE THE FIRST WASH CYCLE
To remove any residual water used during testing by the manufacture r, we
recommend that you carry out a short wash cycle without laundry.
1 Open the tap.
2 Close the door.
3 Pour a little detergent (about 30 ml) into the main wash chamber of the deter-
gent dispenser .
4 Select and start a short programme (see separate quick reference guide).
7
Open the door.
8
A or B
/ soak
A B
9
unds
10
Press the release lever in the main wash compartment downward and remove the
drawer(fig.“C or E”).
Remove siphon in softener slot. (fig.“D or F”).
Refit the siphon in the detergent drawer and fit the drawer back inside its housing.
C D E F
We recommend that you check and clean the filter regularly, at least two or three
times a year.
11
3 Put a flat container under filter door and then drain with emergency drain pipe
(see [draining residual water] for specific operation methods). Then, loosen
filter anticlockwise and completely unscrew and remove the filter.
4
5
6
7
Check the supply hose regularly for brittleness and cracks and replace it if
necessary using a new hose of the same type(available from After-Sales Service
or specialist dealer).
12
G
13
solv
too
14
remove some
15
Hot / Cold fill fault - For Models with Dual Inlets
If you wish to connect hot and cold water supply (Fig.1):
1. Fix the red marked inlet hose to the hot water tap and to the inlet valve with the red
filter on the rear side of machine.
2. Fix the other inlet hose to the cold water tap and to the inlet valve with the blue filter
on the rear side of the machine.
Make sure:
a) The connections are tightly fixed
b) Do not invert their position (for example: cold fill into hot inlet valve and vice versa).
If you wish to connect only the cold fill follow the below instructions (Fig. 2):
1. You will need a Y-piece connector. This can be purchased from local hardware or plumb
ing supplier.
2. Fix the Y-piece connector to the cold fill tap.
3. Connect the two inlet valves present on the rear part of the machine to the Y-piece
connector using the hoses provided.
Ensure that:
All connections are tightly fixed.
Do not allow children to operate, crawl on, be near or inside your washer.
Note that during the wash cycles, the surface temperature of the porthole door may
increase.
Close supervision of children is necessary when the appliance is used near children.
Cold
Hot Cold Cold
fill fill Y- fill
piece fill
16
Fault Code List
Spin Start/Pause
17
C. Fault code
The washer stops when the program is running. The display window shows
fault code “F13”, “F14”, “F24”, else fault codes from “F04” to “F98” or “Unb”.
If fault code “F13” is shown
Door lock is abnormal. Start program for 20 sec and unlock the washer door
(PTC) to check whether the door is closed.
Open or close it again.
After fault is removed, press “Start/Pause” key. If fault occurs again, disconnect
power supply and contact with after-sale service.
If fault code “F14” is shown
Door open fault.
Action: Press “Start/Pause” button. The washing machine will try to open the door.
The alarm will not be removed until the door is unlocked. Or, turn the nub to Off for 3
seconds to turn off the machine. Choose the desired programmme to start the
machine. The alarm will be removed.
If fault code “F24” is shown
Water level reaches overflow level.
Remove it by pressing “Start/Pause” key and feed water.
Select and start required program. If fault occurs again, disconnect power supply
and contact with after-sale service.
If else fault code “F04” to “F98” is shown
Electronic module fails.
Turn the nub to Off for 3 seconds to turn off the machine.
After fault is removed, press “Start/Pause” key. If fault occurs again, disconnect
power supply and contact with after-sale service.
nb” is shown
Unbalance alarm shall be solved by the following methods
1.Laundry winding
Turn the knob to “off” for 3 seconds for shutdown, open the door, shake the clothes and
put them back into the washing machine, then select the single dewatering program to
dry again.
2.Too light-weighted laundry
Turn the knob to “off” for 3 seconds for shutdown, open the door, put in one or two
towels, and then select the single dewatering program to dry again.
18
kg
19
Instruction for use, installation guide, warranty card
(depends on model)
Wrench
C
F
Bottom cover(depends on model)
20
Important: Transport bolts which are not removed can cause damage to the
appliance.
Screw off all transportation bolts for approx. 30mm with wrench following the
direction of arrow shown (not fully screw it off).
30
Pull out transportation bolt together with rubber part and plastic part.
To ensure safety and reduce noise, you should install the transportation bolt
cover supplied with the unit (see the annex accompanying the unit). Lean
and place the transportation bolt into hole and press it following the shown
direction until it clicks.
21
The appliance must be installed on a solid and level floor surface (if necessry
use a spirit level). If the appliance is to be installed on a wooden floor, distribute
the weight by placing it on a 60x60cm sheet of plywood at least 3cm in thickness
and secure it to the floor. If the floor is uneven, adjust the 4 leveling feet as
required; do not insert pieces of wood etc. under the feet.
22
INSTALL BOTTOM COVER
To realize quieter operation, a bottom cover is supplied with the unit (only applies
to some of the Hisense washers). After installing the cover at the bottom of the
washer, the noise level will be greatly reduced. Please ask for advice from
specialists before installing the cover, nevertheless, the machine can be used
without the bottom cover.
8 Noise-Reduction Bottom Plate Installation Instructions
A: Stick acoustic wool to the side of bottom cover plate
with the letter of “PUMP”.
Tilt the washer by 30°-40°, when installing the bottom
cover, please face the side with sound insulation
upwards and attach 'PUMP' at the corner of the cover
PUMP
to the position of the pump in the washer. PUMP
9
If the water inlet hose is not already installed, it must be
screwed to the appliance.The blue marked hose is only
for cold water. Depending on the model, the hot
waterhose marked with red should also be connected,
for models having dual inlets.
10
23
CONNECT THE DRAIN HOSE
11
In case the drain hose is installed
as shown below:
Unhook it only from the right clip (see arrow)
12
Connect the drain hose to the Drain or
hook it over the edge of a sink by means of the
"U" bend.
Fit the “U” bend E, if not already installed, at the
end of the drain hose.
24
2253846-X08061264B