BW6141R Series

5.0” LCD Portable Wireless

Baby Monitoring System

For more exciting new products please visit our website:

Australia: www.uniden.com.au

1
 IMPORTANT SAFETY INSTRUCTIONS
This manual contains important information about this product’s operation. If you
are installing this product for others, you must leave this manual or a copy with the
end user.
When using your equipment, always follow basic safety precautions to reduce the
risk of fire, electric shock and injury to persons, including the following:

• This equipment is NOT waterproof. DO NOT expose it to rain or moisture.

• DO NOT immerse any part of the product in water. Do not use this product near
water, e.g., near a bathtub, wash bowl, kitchen sink or laundry tub, in a wet
basement or near a swimming pool.

• To avoid any risk of electric shock from lightning, avoid handling any electronic
devices (except battery powered ones) during an electrical storm.

• Use only the power cord and/or batteries indicated in this manual. Never dispose
of any batteries in a fire: they may explode. Check with local codes for possible
special disposal instructions.

• Never tug or pull on any power cord: be sure to leave some slack in the cord
when placing your equipment, and always use the plug to unplug cord from the
wall outlet.

• Never leave power cords where they can become crushed, cut, or frayed; when
running power cords, avoid letting them rub against any sharp edges or lie
across any high traffic areas where people might trip over them.

• Do not use the device if the adaptor cords or plugs have been damaged, the unit
has been exposed to liquids, or the unit has been dropped or is damaged.

MAINTAINING YOUR SYSTEM

Monitor
Keep the screen clean by wiping it with a microfiber cloth to remove fingerprints,
dust, etc.
Camera
When dust and grime builds up on the camera lens and glass, it affects the
camera’s “vision.” Use a microfiber cloth to regularly clean the cameras or when
night vision video is cloudy or unclear.

2
Warning to Parents and Other Users
Failure to follow these warnings and the assembly instructions could result in
serious injury or death. This product is not designed or intended for use as a
medical monitor, nor should this product be used as a substitution for medical or
parental supervision. Always be sure that both the transmitter and receiver are
working properly, and are within range of each other.

STRANGULATION HAZARD. Keep the adaptor cords out of the reach of children.

WARNING: KEEP OUT OF THE REACH OF CHILDREN.

Allow for proper ventilation when units are in use. Do not cover the camera or
receiver with any object such as a blanket. Do not place it in a drawer or in any
location which would muffle the sound or interfere with the normal flow of air.

SAVE THESE INSTRUCTIONS!

For best results

To avoid damage to your equipment, follow these simple precautions:
• Do not drop, puncture or disassemble any part of the equipment. There are no
user-serviceable parts inside.
• Do not expose the equipment to high temperatures, and avoid leaving the
equipment in direct sunlight for more than a few minutes. Heat can damage the
case or electrical parts.
• Do not place heavy items on top of the equipment or expose the equipment to
heavy pressure.
• Remove the power adaptor during long periods between usages.
• Clean only with a dry cloth.

Failure to follow the instructions in this operating manual will void the
warranty. Uniden assumes no liability for damages to property or injury to
persons caused by improper handling or failure to comply with these safety
instructions.

3
 CONTENTS
WHAT’S IN THE BOX? .......................................................................................5
GETTING STARTED .............................................................................................6
INSTALLATION ..................................................................................................10
MONITOR INSTALLATION .....................................................................................................................10
CAMERA INSTALLATION ...........................................................................................................................11
PAIRING ............................................................................................................12
PAIRING TWO CAMERAS.................................................................................13
USING THE BABY MONITOR ...............................................................................14
PAN AND TILT .............................. ................................................................................................................. 14
VOLUME ..................................................................................................................................................... 14
MONITOR BRIGHTNESS ......................................................................................................................... 14
PHOTO ......................................................................................................................................................... 14
VIDEO ........................................................................................................................................................... 14
GALLERY ...................................................................................................................................................... 15
LULLABIES .................................................................................................................................................. 15
NIGHT LIGHT .......................................................................................................................................... 16
SYSTEM MENUS ...............................................................................................17
SPECIAL FEATURES ........................................................................................ 21
REMOTE VIEWING VIA APP ................................................................................................................. 21
LIVE VIEW..................................................................................................................................................... 26
HISTORY ...................................................................................................................................................... 27
TROUBLESHOOTING ....................................................................................... 28
SPECIFICATION . ........................................................................................... 29
TWO-YEAR LIMITED WARRANTY .................................................................... 30

4
 WHAT’S IN THE BOX?

BW614PTR BW6100 USB Cable*

Camera* Monitor

AC Adaptor* Screws & Anchors Reset Pin

* Refer to the table below.

Model Name 5.0” Monitor Camera Adaptors
BW6141R 1 1 2 x USB Cable
2 x AC Adaptor
BW6141R+1 1 2 3 x USB Cable
3 x AC Adaptor

• If any item is missing or damaged, contact your place of purchase immediately.

Never use damaged products!
• Need help? Get answers at our website:
www.uniden.com.au for Australian model

All trademarks are registered trademarks of their respective owners.

5
 GETTING STARTED
Camera

3
4

8
9

6
Item What it does
1 Silicone Sleeve
2 Status Light:
Solid Red: Camera is malfunction.
Slow Blinking Red: Waiting for network configuration.
Fast Blinking Red: Waiting for network connection/ Fail to connect to the
network.
Solid Blue: Camera connected to the network.
3 Lens: Camera lens.
4 Microphone: Captures sounds for the area near the camera.
5 PAIR: Press and hold until the prompt tone is heard to start pairing.
Video: Press to activate video call feature through the app. Camera
requires internet connection.
6 Speaker: Produces the sound transmitted from the monitor.
7 MicroSD Card Slot: Insert microSD card (up to 128GB) to record video.
8 Reset: Insert and hold the reset pin until the prompt tone is heard to reset
the camera.
9 USB Port: Connects the USB cable to the camera.

7
Monitor

5
1

2 6
3 7

8
4
9

10

11

12

14

15
16
17
13

8
Item What it does
1 5.0 inch LCD screen.
2 Microphone: Capture sounds and transmits it to the camera.
3 Charging Status LED:
Orange: Charging.
Green: Fully Charged.
If the monitor unplugged from the power, this LED turns off.
4 Power Status:
Off: Monitor is powered Off.
Orange: Monitor is powered On.
5 ZOOM: Zoom the image in 1X, 2X or 4X.
6 MENU: Press to display the menu options.
Press and hold to enter settings interface.
7 Up/Down/Left/Right:
Live View: To pan and tilt the camera (BW61 series).
Menu: Navigate menu and adjust the settings.
8 OK: Press to confirm.
9 TALK: Activate Intercom function.
10 Return: Press to return/back one level.
Press and hold to stop playing lullaby.
11 Antenna: Receives video and audio signals from the camera(s).
12 POWER: Press and hold to turns on the monitor on. Press and hold until a
screen prompt appear on the screen to shut down the monitor to power off
the monitor.
13 Stand
14 MicroSD Card Slot: Insert microSD card (up to 128GB) to record video.
15 Speaker:
16 Reset: Insert and release the reset pin to reset the monitor.
17 USB Port: Connects the USB cable to the monitor.

9
 INSTALLATION
CAMERA INSTALLATION
Placement Considerations
The camera can be placed on a shelf or other flat surface.

• The camera included with your monitor is NOT weatherproof; it is an indoor

camera.
• The clearest line-of-sight between the camera and monitor is best. Walls,
especially brick and concrete, can affect reception quality.
• Avoid having a direct light source in view of the camera (ceiling or floor lamps).
• Carefully plan where and how the camera will be positioned, and where you will
route the cable that connects the camera to the power adaptor.
• When you are positioning the camera, bring the monitor along; it’s much easier
to get the camera into the right position when you have the display handy. Check
the image on the monitor before you install the camera.
# You can install a maximum of 2 cameras. When adding cameras that were not
included in the original box, you will need to pair the cameras with the monitor.

10
Powering the Camera
Insert one end of the micro USB cable to the micro USB port on the camera (at
the back of the camera).
Connect the other end of the USB cable into the USB power adaptor.
Connect the USB power adaptor into a 240 volt AC (standard indoor) power
outlet.
Switch on the plug and allow the camera to power up. The pairing indicator will
flash momentarily.

MONITOR INSTALLATION
Place the monitor in a location with clear reception from your camera(s).
If you are using the monitor as a stand-alone unit, flip out the stand on the back
of the monitor and extend the antenna.
Insert one end of the micro USB cable to the micro USB port on the side of the
monitor.
Connect the other end of the USB cable into the USB power adaptor.
Connect the USB power adaptor into a 240 volt AC (standard indoor) power
outlet.
Press and hold the POWER button to turn the unit on or off. Let the monitor
charge for 6 hours prior to first time use so the built-in rechargeable monitor
battery is fully charged. DO NOT remove the USB cable from the monitor during
the initial charge process. After the initial charge, recharge the monitor as needed.
# We recommend that the device should be fully charged once every three months
with the monitor switched off in order to prolong the device’s battery life.

11
 PAIRING
Viewing the Camera on Monitor
After the camera and the monitor are powered on, the camera will connect to the
monitor automatically. The camera(s) and the monitor are already paired from
the factory. The viewing range is limited to no more than 150m in line of sight.
Other factors such as house walls, layout and electronic devices will affect the
transmission range.
If the camera is not paired to the monitor or additional camera is added, please pair
the camera to the monitor.

Pairing the camera to the monitor:

1. Press the Menu button on the monitor, and select > Camera Management.

2. Press and hold the pairing button on the camera until you hear the prompt tone.

3. Press OK button on the display screen to start pairing.

Unpair the camera from the monitor:
1. Press the Menu button on the monitor, and select > Camera Management.
2. Press and hold OK button on the monitor to unpair the camera.

12
 PAIRING TWO CAMERAS
The BW6181R baby supports up to two camera connections and able to display two
camera feeds at the same time.
To set parameters or enable functions of one of the cameras, you will need to select
the camera first.
Camera Selection:
Press the back key on the home page to enter the camera selection mode. The
camera icon will appear on the camera live view screen and will start flashing.
Press the LEFT or RIGHT button to switch the camera to be controlled and press
OK to select the camera.
To enjoy one camera view, please press OK again after selecting the camera.
The below interfaces are for reference only.

13
 USING THE BABY MONITOR
Pan and Tilt
Pan and tilt the camera (BW614PTR) to adjust the camera viewing angle for an
ideal view.
On the live view page, press the button on the monitor to rotate the camera
horizontally and vertically.

Volume
This option allows you to adjust the volume level for the monitor.
1. Press Menu button on the monitor and select .
2. Press UP and DOWN direction buttons to adjust to adjust the monitor volume
level.

Monitor Brightness
This option allows you to adjust the brightness level for the monitor.
1. Press Menu button on the monitor and select .
2. Press UP and DOWN direction buttons to adjust to adjust the monitor
brightness.

Photo
Take a photo to capture an interesting scene of your baby. Please ensure a micro
SD Card is inserted to take a photo.
Press Menu button on the monitor, select and press OK to take a photo.

Video
Manually record video to capture an interesting scene of your baby. Please ensure a
micro SD Card is inserted to start recording.
1. Press Menu button on the monitor, select and press OK to start recording
2. Press OK again to manually stop the recording.
14
Gallery
Access recorded video and photo in the micro SD Card.
1. Press Menu button on the monitor, select and press OK enter the interface.
2. Select the camera and date, select the photo or video you want to view,and
press OK to view photo or playback video.
* For a video, press OK to play or pause in the preview mode.
* Press Return button to exit preview or return to main menu.

Lullabies
The monitor comes with four lullabies including white noise audio. Play the lullabies
to sooth your baby when baby is crying or sleeping.
1. Press Menu button on the monitor, select and press OK enter the interface.
2. You can control play, stop, repeat or shuffle the lullabies from the monitor. You
may also adjust the camera speaker volume from the monitor.

15
Night light
This option allows you to switch On/Off the LED indicator and the camera night light
and brightness level for the monitor. Only BW618PTR/BW6181R camera supports
night light function.
1. Press Menu button on the monitor and select .
2. Press UP and DOWN direction buttons to select either Status Indicator or night
light and press LEFT or RIGHT to switch is On/Off.

16
 SYSTEM MENU
Feeding Reminder
Set up a reminder alert to feed your baby, or to feed the baby on scheduled time.
1. Press the MENU button on the monitor, and select > Feeding Reminder.
2. Press UP and DOWN direction buttons to select between 4 time options, and
press OK to set the alert time.
3. When setting up the feeding time, press LEFT and RIGHT direction buttons
to change options between hour, minute, second and On/Off; press UP and
DOWN direction buttons to change values or toggle the On/Off switch.
4. Press OK to save settings. You can set up to 4 feeding alert for one day. And
when the set time is up, a feeding alert icon will appear on the screen.

Temperature and Humidity Detection

The baby monitor is able to provide ambient room temperature and humidity level
around the camera as a reference only. If the temperature or humidity falls outside
of a preset range, the system alerts you. Temperature and humidity alert range lets
you set that range.
1. Press the MENU button on the monitor, and select > Temperature and
Humidity Detection.
2. Press UP and DOWN direction buttons to select options between temperature
range, humidity range and out of range reminder, and press OK to confirm
selection.
3. Press LEFT and RIGHT direction buttons to change options, and press UP and
DOWN direction buttons to change values and units.
4. Press OK to save settings.
5. For Out of range reminder option, select to turn on or off the alarm when the
temperature and humidity are out of range.

# Please note that the temperature and humidity indicated in this way should
be used only as a reference, not as an accurate measurement. For a proper
measurement, please use a thermometer or humidity sensor.

17
Smart Care
Motion Detection detects any movement within camera view; Noise Detection
(VOX) and Cry Detection identifies the volume of the baby’s sound or crying.
When any of the detection is above the set threshold, the monitor screen will lit up
when it is in sleep mode or the screen is in standby mode.
1. Press the MENU button on the monitor, and select > Smart Care.
2. Press UP and DOWN direction buttons to select between motion detection,
noise detection, cry detection and alarm volume, and press OK to confirm
selection.
3. When setting up any the detection mode, press UP and DOWN direction buttons
to adjust sensitivity or turn On/Off.
4. When set up the alert volume, UP and DOWN direction buttons to set the
volume level.
5. Press OK to save settings.
6. There will be an alert when the detection is triggered, press OK to stop the alert.

Sleep Mode
Set the monitor to automatically enter sleep mode according to the length of time
set to increase the monitor standby time.
The Power Saving option will NOT turn on the screen if there is alert triggered
on the camera after the monitor enters sleep mode. The microphone on the
monitor is muted. Press OK or power button to turn on the screen.
The Ordinary option allows any alert triggered to turn the LCD back on and alert
and be heard when the monitor enters sleep mode. The audio from the camera is
active in the background.

Any alert triggered will turn the LCD back on. If none of the detection is active,
press the POWER button on the monitor to turn the LCD back on. The Ordinary
option allows you to listen to the audio from the camera when the monitor enters
sleep mode.
1. Press the MENU button on the monitor, and select > Sleep Mode.
2. Press LEFT and RIGHT direction buttons to select the options between Power
saving or Ordinary. or No and then press OK to proceed with the selection.
3. Press OK to save settings.
4. Press the DOWN, then press UP and DOWN direction buttons to select the time
length settings desired for the monitor to enter sleep mode.
5. Press OK to save settings.

18
Light
Set the camera status LED indicator on or off, and turn on night light if required
or set the lighting mode or the light colour for the night light.
1. Press the MENU button on the monitor, and select > Light.
2. Press UP and DOWN Direction buttons to select between Status light or Night
light, and press OK to confirm selection.
3. Press direction buttons to select options or change settings.
4. Press OK to save settings

SD Card
View the total capacity and the free space left in the micro SD Card if it is inserted
to the monitor. The monitor only supports up to 128GB micro SD Card and only
recognise fat32 type micro SD Card. You may format the SD Card as required and
be sure to backup important files before formatting the micro SD Card.
1. Press the MENU button on the monitor, and select > SD Card
Management.
2. Press OK to format the micro SD Card.
3. Press LEFT and RIGHT direction buttons to change options between Yes or No
and then press OK to proceed with the selection.

Wallpaper
Set the wallpaper of the monitor from the system gallery or you may upload your
preferred wallpaper to the micro SD card and select your favourite image as
wallpaper. The supported format in the micro SD Card is jpeg.
1. Press the MENU button on the monitor, and select > Wallpaper.
2. Press directional buttons to select your preferred wallpaper. Select “+” if you
wish to choose the wallpaper from the micro SD Card.
3. Press LEFT and RIGHT direction buttons to change options between Yes or No
and then press OK to proceed with the selection.

19
Date and Time
Set the monitor to automatically enter sleep mode according to the length of time
set to increase the monitor standby time. Any of the detection triggered will turn
the LCD back on. If none of the detection is active, press the power button on the
monitor to turn the LCD back on.
1. Press the MENU button on the monitor, and select > Date and Time.
2. Select the time length desired for the monitor to enter sleep mode.
3. Press OK to save settings.

Reset
This option allows you to restore your system to factory setting. The monitor will
reboot and all menu settings, WILL be affected by the reset.
1. Press the MENU button on the monitor, and select > Reset.
2. Press OK to reset the monitor.
3. Press LEFT and RIGHT direction buttons to change options between Yes or No
and then press OK to proceed with the selection.

Device Information
1. View the monitor and camera firmware version.
2. Press the MENU button on the monitor, and select > Device Information.
3. Press LEFT and RIGHT direction buttons to toggle between the monitor and
camera firmware information.

20
 SPECIAL FEATURES
REMOTE VIEWING VIA APP
You can download Uniden Baby Watch Plus app to remotely view the camera.
To set up the baby monitor camera, please make sure it’s successfully installed and
powered on, and that the status indicator on the camera is flashing red slowly.
The flashing RED (slow) status means that your camera is ready to be paired to the
Baby Watch Plus App.
Prerequisites
• You must have an available Wi-Fi-enabled Smartphone (Android or iOS
smartphone).
• The BW614PTR camera and your smartphone must be within the same Wi-Fi
network range for initial setup (ideally within 3m from the router).
• Wi-Fi router connection is 2.4GHz and password if any.
1. Search and download the free Baby Watch Plus app from the App Store for iOS
devices or Play Store for Android devices. You will need to create an account
specifically for the Baby Watch Plus app. If you already have an account with
Baby Watch Plus app, log in account and skip to Step 6.
2. When the status indicator on the camera starts flashing red slowly, the camera
is ready to be paired with the Wi-Fi network. If the status indicator is not red
or flashing quickly, press and hold the reset button for 5 seconds, wait for the
status indicator to flashing red slowly.

Press and hold for

5 seconds

* Please note that app screenshots are for reference only. User Interface for iPhone and
Android Phones might differ in terms of icons layout and functionality and may change
without notice.
As the Baby Watch Plus app is constantly under development to enrich user experience, the icons/
screens shown may vary slightly from the actual app.
21
2. When launch the Baby Watch app for the first time, you will see the login page.
Tap the “Sign Up” button to create a new Baby Watch Plus account.

3. Enter your email address you wish to register with and check the user
agreement privacy policies. Tap “Next” button to continue.

22
4. Name your account and enter your password. Tap Done button and you’ll be all
set. Your Baby Watch App account has now been created.

2021-05-

5. On the devices tab, to add a device, tap the “+” button on the middle of the
screen or on the top right-hand side of the screen if you already have shared
access or a paired device.

23
6. Please ensure the camera is powered on and is within the range of the router.
Tap “Next” to continue. If the indicator light on the camera is not flashing slowly,
press and hold the reset button with the reset pin for 5 seconds to reset the
camera and set it up within 2 minutes. When the camera is flashing slowly, the
camera is ready to set up tap “Next” to continue.

7. Enter the Wi-Fi password of the selected Wi-Fi network and tap “Next” to
confirm the Wi-Fi name and password. Tap “Ok” to continue. Please note that
the camera only supports 2.4GHz Wi-Fi connection and the Wi-Fi SSID and
password must not exceed 24 characters.

24
8. Please make sure that you’ve ripped the protection film off the camera’s lens.
Tap “Next” and a QR code will be generated on the screen. Please place the
QR code on screen towards the camera lens at a distance of about 15~20cm
to let the camera scan the QR code. After you hear the voice prompt from the
camera, please press “Next” to continue.

9. Please wait while the app is configuring your camera. Once completed, you’ll be
prompted to name your camera and tap “Done” to start the Live View.

25
LIVE VIEW

Back Device Settings

Date & Time 2021-05-01 15:00:00 2021-05-01 15:00:00

Tap to switch streaming

resolution
SD Full Screen Mode SD
Streaming rate &
Wi-Fi Strength

Two-way talk

Take Snapshot Local Recording

Motion Alert
View and set the
temperature and Pan and Tilt
humidity alerts.

Scroll to the right.

2021-05-01 15:00:00 2021-05-01 15:00:00

SD SD

Play, repeat or
shuffle lullabies

Access local gallery

26
HISTORY

2021-05-01 15:00:00

SD
View playback
file timeline

View alert event history

Choose the date to

Take a snapshot while
search for videos.
playback recorded video

Record playback video

Access local gallery
to local gallery

# Please note that a SD Card is needed and inserted to the camera for the
lullabies to download and playback.
# Only the event recording and Full-Day recording are saved in the SD Card. Any
event history is saved in the SD Card.
# Local recording and snapshot are saved to the phone gallery.

27
 TROUBLESHOOTING
If you have problems with the system, there is often a quick and simple solution.
Please try the following:
If Try
There is no picture on • checking all connections to the camera. Make sure
the monitor from the the adaptor is plugged in.
camera • making sure that the cameras and monitor are both
ON.
• making sure that the camera is in range of the
monitor.
The picture keeps • moving the camera closer to the monitor.
dropping on the • repositioning the camera, monitor or both to improve
monitor the reception.
• adjusting the monitor antenna to vertical position.
There are audio • making sure that there is sound within range of the
problems camera microphone.
• moving the camera or monitor farther apart if the unit
emits a loud screeching noise.
There is an irregular That is the Alert tone. Go to the Alert screen to turn the
beeping coming from alert volume down or off .
the monitor
The picture has The picture may become choppy when experiencing a
become choppy lower frame rate. Try:
• moving the camera closer to the monitor.
• removing obstructions between the monitor and
camera.
• adjusting the monitor and antenna to vertical position.
The monitor picture Use the reset pin included to reset the monitor. The
has frozen monitor turns off. Press POWER to turn it back on again.
You can’t record video Ensure a micro SD Card is inserted and format the SD
or take a snapshot card with the system. The SD Card needs to be FAT32
format.
The camera is not Make sure the Wi-Fi router supports DHCP protocol and
found when setting up the option is turned on.
or could not connect to Make sure the camera and your mobile device connect
the router. to the same Wi-Fi router and selected the correct
2.4GHz Wi-Fi SSID and entered the correct password.

28
 SPECIFICATION
CAMERA
Image Sensor 1/2.8” Colour CMOS
Video Resolution 2304 x 1296
Rotation Angle Pan:0~355°
Tilt: -15°~45°
Viewing Angle 105°
Two-way Audio Yes
Night Vision Up to 10m
Temperature Sensor Yes
Humidity Sensor Yes
Wi-Fi 2.4G WIFI (IEEE802.11b/g/n)
Transmission Range Wi-Fi: up to 50m line of sight
Monitor: up to 150m Line of sight
Smart Home Google Assistant / Alexa
Storage Supports up to 128GB micro SD Card
Power Input 5V/1A
Operating Temperature Range –10°C ~ 40°C (14°F ~ 104°F)
Operating Humidity Range Within 80% Relative Humidity

MONITOR
Display 5.0” LCD
Resolution 1280 x 720
Two-way Audio Yes
Storage Supports up to 128GB micro SD Card
Battery Capacity 3000mAh
Battery Life Up to 5 hours
Power Input 5V/1A
Operating Temperature Range –10°C ~ 40°C (14°F ~ 104°F)
Operating Humidity Range Within 80% Relative Humidity

29
 TWO-YEAR LIMITED WARRANTY
BW6141R Series
IMPORTANT Satisfactory evidence of the original purchase is required for
warranty service.Please refer to our Uniden website for any details or warranty
durations offered in addition to those contained below.

Warrantor
The warrantor is Uniden Australia Pty Limited ABN 58 001 865 498
(“Uniden Aust”) .

Terms of Warranty
Uniden Aust warrants to the original retail purchaser only that the BW6141R Series
(“the Product”), will be free from defects in materials and craftsmanship for the duration
of the warranty period, subject to the limitations and exclusions set out below.

Warranty Period
This warranty to the original retail purchaser is only valid in the original country of
purchase for a Product first purchased either in Australia or New Zealand and will expire,
as indicated below, from the date of original retail sale.

Product 2 Year
Accessories 90 Days

If a warranty claim is made, this warranty will not apply if the Product is found by
Uniden to be:
(A) Damaged or not maintained in a reasonable manner or as recommended in the
relevant Uniden Owner’s Manual;
(B) Modified, altered or used as part of any conversion kits, subassemblies or any
configurations not sold by Uniden Aust;
(C) Improperly installed contrary to instructions contained in the relevant Owner’s
Manual
(D) Repaired by someone other than an authorized Uniden Repair Agent in relation to
a defect or malfunction covered by this warranty; or
(E) Used in conjunction with any equipment, parts or a system not manufactured by
Uniden.

Parts Covered
This warranty covers the Product and included accessories.

30
User-generated Data
This warranty does not cover any claimed loss of or damage to user-generated data
(including but without limitation phone numbers, addresses and images) that may be
stored on your Product.

Statement of Remedy
If the Product is found not to conform to this warranty as stated above, the Warrantor,
at its discretion, will either repair the defect or replace the Product without any charge
for parts or service. This warranty does not include any reimbursement or payment of
any consequential damages claimed to arise from a Product’s failure to comply with
the warranty.
Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure and
for compensation for any other reasonably foreseeable loss or damage. You are also
entitled to have the goods repaired or replaced if the goods fail to be of acceptable
quality and the failure does not amount to a major failure.
This warranty is in addition to and sits alongside your rights under either the
COMPETITION AND CONSUMER ACT 2010 (Australia) or the CONSUMER
GUARANTEES ACT (New Zealand) as the case may be, none of which can be
excluded.

Procedure for Obtaining Warranty Service

Depending on the country in which the Product was first purchased, if you believe
that your Product does not conform with this warranty, you should deliver the Product,
together with satisfactory evidence of your original purchase (such as a legible copy
of the sales docket) to Uniden. Please refer to the Uniden website for address details.
You should contact Uniden regarding any compensation that may be payable for your
expenses incurred in making a warranty claim. Prior to delivery, we recommend that
you make a backup copy of any phone numbers, images or other data stored on your
Product, in case it is lost or damaged during warranty service.

UNIDEN AUSTRALIA PTY LTD

Phone number: 1300 366 895
Email address: custservice@uniden.com.au

31
 ©2022 Uniden Australia Pty Ltd
Printed in PRC v1.1

32