Sekonda Uputstvo

ATTENTION BACKLIGHT
1. Never try to open the case or remove its back cover. • The backlight uses an electro-luminescent which
causes the display to glow for easy reading in the dark.
1. EL Backlight 2. Do not operate the buttons under water.
1. In any mode press “A” to
2. Alarm 3. Should moisture appear inside the watch, have it illuminate the display for
checked immediately by your dealer. Otherwise about 3 seconds;
it can cause erosion on the metal parts of the watch.
3. Chime
4. Although the watch is designed to withstand normal
4. Stopwatch use, you should avoid rough use or dropping the watch.
5. Avoid exposing the watch to extreme temperatures.

5. CR2025 battery
6. Wipe the watch with dry and soft cloth only. Avoid
6. 50m water resistant allowing the watch to come into direct contact with
chemical materials that can cause deterioration of the
plastic parts on the watch.
BUTTONS
7. Avoid wearing the watch in electromagnetic and static
• Button operations are indicated using the letters conditions.
shown on the below illustration. TIME KEEPING
MODE SELECTION • Always use the timekeeping mode when the stop
-watch, alarm and time setting modes are not in use.
• Press “B” to change the mode in the following
sequence: Time keeping mode Stopwatch
• In the time keeping mode the hour, minute, seconds,
mode Alarm mode Time setting mode.
month, date and day are displayed.
TIME KEEPING MODE

1. In the time keeping mode press
• Hour, minute, seconds, month, date “D” to check the month and date.
and day display.
• Alarm on/off.
A – Light • Chime (hourly time signal) on/off.
B – Mode
C – Reset
D – Start / Stop 2. Press “C” to check the alarm time.
STOPWATCH MODE
• 1/100 second measurement.

DISPLAY • Split time.
• The screen is shown below: ALARM AND CHIME ON/OFF
ALARM MODE 1. In the time keeping mode press

and hold “C”, then press “D” to
• Setting the alarm. turn the alarm on and off.
• Snooze.
Day of the week
TIME SETTING MODE 2. Press and hold “C”, then press

Hour Seconds “B” to turn the chime on and off.
• 12/24H format.
Minute • Setting the hour, minute, seconds, (The days of the week will show
month, date and day. when the chime is on).
IS47D
STOPWATCH ALARM TIME SETTING
1. In the time setting mode the seconds
• The alarm will sound at the pre-set time each day.
will flash, press “D” to reset the
1. In the stopwatch mode press
seconds;
“D” to start the stopwatch;
1. In the alarm mode the hour will flash. 2. Press “C” to select the minutes. The
2. Press “D” to stop the stopwatch or minutes will begin to flash.
press “B” to change the mode while Press “D” to adjust the hour, press
and hold “D” to adjust the hour quickly;
the stopwatch is running. The stop
-watch will continue timing in the
background. 3. Press “D” to adjust the minutes,
(The letter A will represent AM and the letter P press and hold “D” to adjust the
will represent PM time setting. The letter H will minutes quickly
3. Once you have finished timing, represent 24 hour time setting).
press “B” repeatedly until you
return to the stopwatch mode;
4. Press “C” to select the hour. The
2. Press “C” to select the minutes. The hour will begin to flash.
minutes will begin to flash.
4. Press “D” to stop the stopwatch;

5. Press “D” to adjust the hour, press
and hold “D” to adjust the hour
quickly;
3. Press “D” to adjust the minutes, press
and hold “D” to adjust the minutes (The letter A will represent AM and the letter P
5. Press “C” to reset the stopwatch. quickly; will represent PM time setting. The letter H will
represent 24 hour time setting).
SPLIT TIME 6. Press “C” to select the date. The

4. Press “B” to change to the next mode, date will begin to flash.
after you have set your alarm.
1. In the stopwatch mode press
“D” to start the stopwatch;
7. Press “D” to adjust the date,
press and hold “D” to adjust the
(Always ensure that your alarm is on by date quickly;
2. Press “C” to display the split following step 1 under the ‘ALARM AND
time. The stopwatch will continue CHIME ON/OFF’ section on page 3).
timing internally.
8. Press “C” to select the month. The
month will begin to flash.
SNOOZE
3. Press “C” to clear the split time
and continue time measurement;
9. Press “D” to adjust the month,
1. When the alarm sounds, press “D”
4. Repeat steps 2 and 3 to measure press and hold “D” to adjust the
to stop the alarm or press “B” to
multiple split times; month quickly;
snooze the alarm;
5. Press “D” to stop the stopwatch;

10. Press “C” to select the day. The
(The alarm will sound again after five minutes day will begin to flash.
to signal that the snooze period is over).
6. Press “C” to reset the stopwatch. 11. Press “D” to adjust the day,
2. Press “D” to stop the snooze
press and hold “D” to adjust the
alarm.
day quickly.
7. Press “B” to change to the next mode,
after you have finished using the stopwatch. 12. Press “B” to change to the next mode.

Sekonda Uputstvo

Uploaded by

Copyright:

Available Formats

Sekonda Uputstvo

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Sekonda Uputstvo

Uploaded by

Copyright:

Available Formats

ATTENTION BACKLIGHT

5. Avoid exposing the watch to extreme temperatures.

TIME KEEPING MODE

• 1/100 second measurement.

• The screen is shown below: ALARM AND CHIME ON/OFF

ALARM MODE 1. In the time keeping mode press

TIME SETTING MODE 2. Press and hold “C”, then press

4. Press “D” to stop the stopwatch;

SPLIT TIME 6. Press “C” to select the date. The

5. Press “D” to stop the stopwatch;

You might also like