SECTION 10 28 00 Toilet, Bath, and Laundry Accessories
SECTION 10 28 00 Toilet, Bath, and Laundry Accessories
SECTION 10 28 00 Toilet, Bath, and Laundry Accessories
SECTION 10 28 00
TOILET, BATH, AND LAUNDRY ACCESSORIES
PART 1 - GENERAL
1.1 DESCRIPTION
A. SUMMARY:
1. Section Includes: Toilet and bath accessories at dressing rooms,
toilets, baths, locker rooms and other areas indicated on drawings.
1.2 RELATED WORK
SPEC WRITER NOTE: Update and retain
references only when specified elsewhere
in this section.
10 28 00 - 1
01-01-21
10 28 00 - 2
01-01-21
C1048-18 Heat-Strengthened
and Fully Tempered Flat Glass.
D635-18 Rate of Burning
and/or Extent and Time of Burning of Plastics in
a Horizontal Position.
F446-19 Grab Bars and
Accessories Installed in the Bathing Area.
E. Federal Specifications (Fed. Spec.):
A-A-3002 Mirror, Glass.
FF-S-107C(2) Screws, Tapping
and Drive.
WW-P-541/8B(1) Plumbing Fixtures
(Accessories, Land Use).
F. National Architectural Metal Manufacturers(NAAMM):
AMP 500-06 Metal Finishes
Manual.
1.4 SUBMITTALS
A. Submittal Procedures: Section 01 33 23, SHOP DRAWINGS, PRODUCT DATA, AND
SAMPLES.
B. Submittal Drawings:
1. Show size, configuration, and fabrication, anchorage and installation
details.
2. Show mounting locations and heights.
C. Manufacturer's Literature and Data:
1. Description of each product.
2. Installation instructions.
D. Samples:
1. Full sized, complete assembly of each product specified.
2. Approved samples may be incorporated into project.
E. Certificates: Certify each product complies with specifications.
1. Soap dispensers: Certify soap dispensers are fabricated of material
that will not be affected by liquid soap, aseptic detergents, and
hexachlorophene solutions.
F. Qualifications: Substantiate qualifications comply with specifications.
1. Manufacturer // with project experience list //.
G. Operation and Maintenance Data:
1. Care instructions for each exposed finish product.
10 28 00 - 3
01-01-21
10 28 00 - 4
01-01-21
C. Products Used Within Mental Health and Behavioral Patient Care Units:
1. Provide accessories free of anchor points.
2. Design accessories for attachment with tamper resistant hardware.
SPEC WRITER NOTE: Specify only toilet
accessories applicable to project. Many
products that include disposables (paper
or soap) are vendor provided and possibly
installed. Coordinate with the station.
10 28 00 - 5
01-01-21
10 28 00 - 6
01-01-21
10 28 00 - 7
01-01-21
H. Grab bars in Mental Health and Behavioral Patient Care Units: Provide
units complying with accessibility standards, but preventing materials
from being threaded between bar and wall as possible anchor point.
2.8 SHOWER CURTAIN RODS
A. Stainless steel tubing, minimum 1.27 mm (0.050 inch) wall thickness,
32 mm (1-1/4 inch) outside diameter.
B. Flanges, stainless steel rings, 66 mm (2.6 inch) minimum outside
diameter, with 2 holes opposite each other for 6 mm (1/4 inch) stainless
steel fastening bolts. Provide set screw within curvature of each flange
for securing rod.
SPEC WRITER NOTE: Use intermediate support
for intersection of rods or where bent rod
occurs. Show on details.
10 28 00 - 8
01-01-21
C. Clothes Hooks Used In Mental Health And Behavioral Patient Care Units:
Provide units free of anchor points and secured to the wall using tamper
resistant hardware.
2.10 TOWEL BARS
A. Fed. Spec. WW-P-541/8B, Type IV, Bar, Surface mounted; Class 1, towel.
B. Stainless steel, or chromium plated copper alloy.
C. Bar Length: 450 and 600 mm (18 and 24 inches) as shown.
D. Finish brackets and supports to match bar.
SPEC WRITER NOTE: Use the following
paragraph for towel bars used in Mental
Health and Behavioral Patient Care Units.
E. Towel Bars Used in Mental Health and Behavioral Patient Care Units:
Design units to support maximum 1 kg (2 lbs.).
SPEC WRITER NOTE: See VA standard detail
SD102800-3 for accessible lavatory with
metal framed mirror.
www.cfm.va.gov/TIL/sDetail.asp
10 28 00 - 9
01-01-21
F. Metal Framed Mirrors used in Mental Health and Behavioral Patient Care
Units: Provide shatter proof glass or polished stainless steel units.
SPEC WRITER NOTE: Delete cabinet types not
used. Ensure cabinets are detailed.
10 28 00 - 10
01-01-21
5. Provide door with full length stainless steel piano hinge, magnetic
or friction catches, rubber bumpers, and 90 degree restraining arm
with spring type stop.
C. Sliding Door:
1. Slide door.
2. Fabricate sliding doors for approximately 660 by 560 mm (26 by
22 inch) opening.
3. Provide nylon glides in stainless steel tracks, door pulls and rubber
bumpers.
4. Entire contents of cabinet concealed when doors closed.
SPEC WRITER NOTE: Use the following
paragraph for medicine cabinets used in
Mental Health and Behavioral Patient Care
Units.
10 28 00 - 11
01-01-21
D. Soap Dishes in Mental Health and Behavioral Patient Care Units: Provide
recessed units.
2.15 PAPER CUP DISPENSER
A. Fabricate of stainless steel.
B. Provide door with concealed stainless steel pivoting rod or piano hinge,
and spring tension cam lock, or tumbler lock, keyed alike when more than
one accessory unit is provided, and with cup level refill sight slot in
door front.
C. Fabricate for flat bottom cups.
D. 90 Milliliters (3 ounce) Dispenser Unit:
1. Surface mounted single stack dispenser unit having a capacity of
maximum one hundred fifty cups.
2. Form door from one piece to cover front and sides warp free.
E. 120 Milliliters (4 ounce) Dispenser Unit:
1. Recessed type single stack dispenser unit having a capacity of
Maximum one hundred cups.
2. Form face frame in one piece.
3. Fabricate door double-pan warp free.
F. Combination 90 to 180 Milliliters (3 to 6 ounce) Dispenser and Disposal
Unit:
1. Recessed type, having a capacity of Maximum 170 cups.
2. Fabricate as twin stack dispenser unit with adjustable dispensing
mechanism to dispense any size cup.
3. Fabricate face frames in one piece and doors double pan warp free.
4. Fabricate recessed disposal unit with removable waste receptacle
having a capacity of minimum 11 L (3.1 gallons).
2.16 MOP RACKS
A. Minimum 1016 mm (40 inches) long with five holders.
B. Clamps:
10 28 00 - 12
01-01-21
10 28 00 - 13
01-01-21
10 28 00 - 14
01-01-21
10 28 00 - 15
01-01-21
10 28 00 - 16
01-01-21
- - E N D - -
10 28 00 - 17