Psan en Tcd210185ab 20220523 Manual W
Psan en Tcd210185ab 20220523 Manual W
Psan en Tcd210185ab 20220523 Manual W
01. Fail-safe device must be installed when using the unit with machinery that
Display Type
may cause serious injury or substantial economic loss. (e.g. nuclear power
control, medical equipment, ships, vehicles, railways, aircraft, combustion
apparatus, safety equipment, crime/disaster prevention devices, etc.)
Pressure Sensors
Failure to follow this instruction may result in personal injury, economic loss or fire.
02. Do not use the unit in the place where flammable/explosive/corrosive gas,
humidity, direct sunlight, radiant heat, vibration, impact, or salinity may be
present.
Failure to follow this instruction may result in explosion or fire.
03. Install on a device panel or to a pressure port directly to use.
Failure to follow this instruction may result in fire.
04. Do not connect, repair, or inspect the unit while connected to a power
source.
Failure to follow this instruction may result in fire.
05. Check 'Connections' before wiring.
Failure to follow this instruction may result in fire.
06. Do not disassemble or modify the unit.
Failure to follow this instruction may result in fire or electric shock.
PRODUCT MANUAL
• Follow instructions in ‘Cautions during Use’.
Otherwise, it may cause unexpected accidents.
• 12 - 24 VDCᜡ power supply should be insulated and limited voltage/current or Class 2,
SELV power supply device.
• Use the product, 3 sec after supplying power.
For your safety, read and follow the considerations written in the instruction
• When using switching mode power supply, frame ground (F.G.) terminal of power
manual, other manuals and Autonics website.
supply should be grounded.
The specifications, dimensions, etc are subject to change without notice for product
• Wire as short as possible and keep away from high voltage lines or power lines, to
improvement Some models may be discontinued without notice.
prevent inductive noise.
• This unit may be used in the following environments.
- Indoors (in the environment condition rated in ‘Specifications’)
- Altitude max 2,000 m
Features - Pollution degree 3
- Installation category II
• Pressure measurement of any gas, liquid or oil (except substances which may corrode
stainless steel 304/316L)
• Auto shift function: with change in the original pressure, the external input adjusts the
determined level to match the change in pressure (only available in models with auto
shift/hold function)
• Hold function: hold current display value or control output
• Forced output control mode for device testing and maintenance
• One-touch connector type for easy wiring and maintenance
• Zero-point adjustment function, peak value monitoring function, chattering
prevention function
ᜢᜫ
-|Transparent Guide|-
20
D: Pneumatic type (gas) / Bottom P: PNP open collector output 12 R1/8 8 tap
B: Fluid type (liquid, gas) / Back
❺ Option input / output
L: Fluid type (liquid, gas) / Bottom ■ Pneumatic type, bottom port, connector type
V: Voltage output
cable
❷ Pressure type and Range A: Current output 30 32
20 2-M3
H: External input
Pressure Rated range
01 0.0 to 100.0 kPa ❻ Pressure port
Static
20
1 0 to 1,000 kPa
39
Medium
Pneumatic Fluid
V01 Negative 0.0 to -101.3 kPa Port
C01 Compound -101.3 to 100.0 kPa R1/8 ○ ○
Rc1/8(standard), NPT1/8
Rc1/8 ○ -
❸ Wiring NPT1/8 ○ ○ ■ Fluid type, bottom port, connector type
No mark: Cable type (fluid type) 7/16-20UNF - ○ 30 32 20 2-M3
C: Connector type 9/16-18UNF - ○
Port A B
R1/8
20
30
41.3
(standard) 8 Inner M5
Product Components NPT1/8
tap
11.3
• Product • Instruction manual • Unit sticker 7/16-
17 11 -
20UNF
A
B
• Connector type: Bracket A / B, Connector wiring (PSO-C01)
• Cable type: Bracket C ■ Fluid type, back port, cable type
42.3
30 30 12.3 A B 20 2-M3
Sold Separately
Port A B
• Front cover (PSO-P01), Panel bracket (PSO-B02/B03)
20
30
R1/8 Inner M5
8
• Pneumatic type: M5 gender (PSO-Z01) 17 (standard) tap
9/16-
15.4 -
Ø4, 3m 18UNF
5.1
Unit Descriptions
■ Bracket A ■ Bracket B ■ Bracket C
1. Pressure range (sticker) 30
2. Display part (red)
4.2
4.2
1 Run mode: Displays PV (present value), SV (setting 20 3-Ø3.2 22
6
25 22
value)
2 35 Ø4.2
3.5
Setting mode: Displays parameter and setting value Ø22 20 4-Ø3.2
30
3. Output indicator (OUT1: red , OUT2: green) 20 3-Ø3.2
3 3 Turns ON when the corresponding control output is
45
40
4.2
ON. 20
4
20
15
55
4. [M] key 20 Ø4.2 1.6
40
45
40
30 13
Enters parameter group, selects item and returns
1.6
20
36 15
5 run mode.
5. [▼] , [▲] key
Sets preset of output operation mode, runs the
Installation
mode or changes parameter.
■ One-touch fitting
Connections Pneumatic type Fluid type
Connect the metal part with a
Color Function spanner so that no large force is
Brown +V 12 mm
Blue 0V
applied to the unit body.
spanner 17 mm
Black OUT 1 spanner
(tightening torque: ≤ 10 N m, it may
White OUT 2 cause malfunction.)
Orange Option input / output
White
LOAD
OCP ① ②
① ② Orange
Orange
Output
Output impedance
impedance
Blue Blue
Pressure Type
Pneumatic type model: Gauge pressure [M] → Preset setting [M] →
Fluid type model: Gauge pressure 01) or sealed gauge pressure 02)
[▼]+[▲] for over 1 Zero-point
Pressure Negative Static Compound RUN Displays 0.0 and RUN
sec after remove the → →
adjustment returns automatically
Min display unit 0.1 kPa 0.1 kPa 1 kPa 0.1 kPa external pressure
Rated pressure 0.0 to -101.3 0.0 to 100.0 -101.3 to 100.0 [M] →
range kPa kPa
0 to 1,000 kPa
kPa Max / Min monitoring
[▲] for over 3 sec → Reset or set: [▼]+[▲]
/ Auto shift 01) →
Display & setting 5.0 to -101.3 -5.0 to 110.0 -101.3 to 110.0 for over 1 sec
-101.3 to 1,100 kPa
pressure range kPa kPa kPa
01) Max. / Min. pressure value is available to check by monitoring.
Display type 7 Segment LED, 4 ½ digit [Option external input model] Auto shift judgment level checking / setting is available when P-9 External input
Display accuracy -10 to 0 ℃: ≤ ±1% F.S., 0 to 50 ℃: ≤ ±0.5% F.S. terminal is set as SHFT. (no input displays 0)
• Pneumatic type:
Rated pressure Rated Rated pressure ×1.5 Rated pressure
Max. pressure
×2 pressure ×2 • Fluid type: Rated ×2 Parameter Setting
pressure ×2
01) Only for static pressure, rated pressure range 100.0 kPa model • Some parameter are activated / deactivated depending on other parameters. Refer to
02) The unit is sealed structure. It is based on atmospheric pressure 101.3 kPa. the description.
• The setting item name and setting value are cross-displayed on the display part.
Fluid type (non-corrosive gas and
Applicable Pneumatic type • It returns to RUN mode when there is no additional key input for 60 sec in each
fluid that do not corrode stainless
medium (air, non-corrosive gas)
steel 316L) parameter group.
Connection type Connector type Cable type / connector type • Guaranteed write life: 100,000 times
Connector type: Ø 4 mm, 5-core, 2 m • [M] key: Saves setting value and moves to next parameter
Cable Ø 4 mm, 5-core, 2 m
Cable type: Ø 4 mm, 5-core, 3 m [▼], [▲] key: Selects setting value
Wire spec. AWG24 (0.08 mm, 40-core), insulator diameter: Ø 1 mm
Parameter Display Default Setting range
Front case: PC
Front case: PC [Negative / Compound pressure model]
Back case: (back port) PC / (bottom
Material Back case: PA6 kPa, KGC: kgf/cm2, bar, psi, mmHg, inHg, H2O: mmH2O
KPA
port) PBT+GF15% P-1 Display unit
Pressure port: SUS304/SUS316L [Static pressure model]
UNIT
Pressure port: Brass-nickel plated
MPa, kPa, KGC: kgf/cm2, bar, psi
MPA
Protection Connector type: IP40 (IEC standard)
Connector type: IP40 (IEC standard) HYS.M: Hysteresis
structure Cable type: IP65 (IEC standard)
OUT WIN: Window comparison output
Approval ᜢᜫ P-2 operation OUtM OFF HY-W: Hysteresis-Window comparison output
Unit weight Back port: ≈ 80 g (≈ 165 g) Connector type: ≈ 88 g (≈ 173 g) mode AUTO: Auto sensitivity setting
(packaged) Bottom port: ≈ 85 g (≈ 170 g) Cable type: ≈ 90 g (≈ 167 g) F.OUT: Forced output control
OUT1 OUT2
Power supply 12 - 24 VDCᜡ (ripple P-P: ≤ 10%) 1O2O Normally open Normally open
Allowable voltage P-3 Output type 1O2O 1O2C Normally closed Normally open
90 to 110% of rated voltage
NoNC
range 1C2O Normally closed Normally open
Current consumption ≤ 50 mA 01) 1C2C Normally closed Normally closed
Control output NPN open collector output / PNP open collector output model Response
P-4 @5 2.5, 5.0, 100, 500, 1,000 ms
Load voltage ≤ 30 VDCᜡ time
SPD
• Setting name and value are cross-displayed in SV display part. ON: OFF: H: Hysteresis A: Min display interval
1. Set the operation mode in P-2 OUT operation mode.
■ Hysteresis ■ Window comparison output
2. Enter the preset setting mode by pressing [M] key from RUN mode.
3. Select the setting item by [M] key and change the preset by [▼] or [▲] key. • Set the hysteresis for pressure detection • It detects pressure at the desired range.
4. Press [M] key to save setting or no key input over 60 sec not to save setting and directly. • Hysteresis is fixed as min. display interval.
return to RUN mode. (except forced output control mode) • Setting: Pressure detection level (ST1, • Setting: High limit (HI1, HI2), Low limit
ST2), Hysteresis (HYS1, HYS2) (LO1, LO2)
■ Preset setting by operation mode
Pressure
Operation mode Preset Setting range Pressure A
HI2
Pressure Min. display pressure < ST1 ≤ Max. display H A
ST2 / HYS2 LO2
detection level 1 ST1 pressure
A
HI1
Hysteresis level 1 Min. display pressure ≤ HYS1 < ST1 ST1 / HYS1
H
Hysteresis A
HYS1
HYsM
Pressure Min. display pressure < ST2 ≤ Max. display LO1
detection level 2 ST2 pressure Time Time
Hysteresis level 2 HYS2 Min. display pressure ≤ HYS2 < ST2 OUT1 N.O. OUT1 N.O.
Pressure ST1 / HYS1 LO1 / HYS1
Min. display pressure ≤ LO-1 ≤ Max.
detection low LO-1 display pressure -(3 × Min display interval) OUT1 N.C. OUT1 N.C.
limit 1 ST1 / HYS1 LO1 / HYS1
OUT2 N.O. OUT2 N.O.
Pressure
LO-1 + (3 × Min display interval) ≤ HI-1 ≤ ST2 / HYS2 LO2 / HYS2
detection high HI-1 Max. display pressure
Window limit 1
OUT2 N.C. OUT2 N.C.
ST2 / HYS2 LO2 / HYS2
comparison
Pressure
output 01)
■H
ysteresis - Window
WIN
Min. display pressure ≤ LO-2 ≤ Max.
detection low LO-2 display pressure - (3 × Min display interval)
limit 2 comparison output ■ Auto sensitivity setting
Pressure
LO-2 + (3 × Min display interval) ≤ HI-2 ≤ • It is available both hysteresis mode • This function is to set the proper position
detection high HI-2 Max. display pressure
limit 2 and window comparison output mode (SET) automatically by applied pressure
Pressure Min. display pressure < ST1 ≤ Max. display operations. from two positions (ST1, ST2).
detection level 1 ST1 pressure
• Setting: Pressure detection level (ST1),
(ST1+ST2)
SET=
2
Hysteresis level 1 HYS1 Min. display pressure ≤ HYS1 < ST1
Hysteresis- Hysteresis (HYS1), High limit (HIGH), Low • Hysteresis is fixed as min. display interval.
Window Pressure
HY-W detection low
Min. display pressure ≤ LOW ≤ Max. limit (LOW)
comparison LOW display pressure - (3 × Min display interval)
output 02) limit Pressure Pressure
Pressure HIGH
A
ST2
A
Low + (3 × Min display interval) ≤ HIGH ≤
detection high HIGH Max. display pressure A
LOW
limit SET
A
ST1
Min. display pressure ≤ ST1 ≤ Max. display
Pressure level 1 ST1 pressure - 1% of rated pressure HYS1 ST1
A
■ Precaution
Min. memorized input
• Auto shift correction is reset as 0 when changing P-2 OUT operation mode and preset
value. Time Time
• Preset setting range is wider than the rated pressure with the source pressure
fluctuations.
• In case of forced output control mode or PV HHHH/LLLL, Auto shift function does
Display / Output Scale
not operate. Customizes the scale of display / output value from rated output range. If the measured
input is a, b, and the arbitrary values to
be displayed are A, B, the display / output value
are outputted for input a and b linearly (a = A, b = B).
Error
Display / Output Display / Output
Display Cause Troubleshooting Display / Output
B A
When external pressure is input while Try again after removing external B
adjusting zero point. pressure.
ERR1
-HH-
Set the corrected setting value within
Auto shift correction error. Prevents chattering of the output by changing the response time of the control output
setting pressure range.
-LL-
-HL- and pressure display value.
When the response time is longer, the number of digital filter increase, so stable
measurement is possible, but the measured value may differ from the actual input
value.
Linearity
Min. Output
Input Input
Rated input
range
Display input range
-|Transparent Guide|- -
■ Auto shift • Unit: mm, For the detailed drawings, follow the Autonics website.
The judgment level is corrected by applying the standard pressure which is set ■ Front cover (PSO-P01) ■P
anel bracket
when external input signal is applied. 40 5.7 (PSO-B02/B03)
9.7
• Correction set value ST1 = ST1 + SH.IN
1
28.2
SH.IN is the reference pressure set by Auto shift input.
40
42
35
26
40
42
• When auto shift is not used
30
Increase of primary 40
3
Normal primary pressure 20
Pressure 25.8
pressure Drop of primary
pressure ■ Panel cut-out ■ Installation configuration
Setting pressure
□36 +0.5
Hysteresis • Sold separately: Front cover (PSO-P01),
0
Time
R1/8 or
Time
ON 1.6 NPT1/8
Output
OFF 8.1
Time
Auto shift input Auto shift input
Pressure Conversion Chart
Reference pressure Reference pressure Reference pressure
= Atmospheric ≤ Atmospheric ≥ Atmospheric Pa kgf/cm2 mmHg mmH2O psi bar inHg
pressure (0.0kPa) pressure (0.0kPa) pressure (0.0kPa)
Pa 1 0.000010197 0.007501 0.101972 0.00014504 0.00001 0.0002953
■ Remote zero kgf/cm2 98066.5 1 735.5592 10000.0005 14.223393 0.980665 28.959025
Executes zero-point adjustment function when external input signal is applied. mmHg 133.3224 0.001359 1 13.595099 0.019337 0.001333 0.039370
Detection area 7 P 7 P 7 P 7 P
Detection area
7 P 7 P 7 P 7 P
8 Q 8 8 Q Q 8 Q 8 Q
Time Time
8 Q 8 Q 8 Q
Output Output 9 R 9 9 R R 9 R 9 R
ON ON
9 R 9 R 9 R
A S A S A S A S
OFF OFF
A S A S A S A S
Time Time B B T T B B T T B B T T B B T T
Hold ON Hold ON C C U U C C U U C C U U C C U U
Input OFF Input OFF D D V V D D V V D D V V D D V V
E E W W E E W W E E W W E E W W
F F X X F F X X F F X X F F X X
G G Y Y G G Y Y G G Y Y G G Y Y
H H Z Z H H Z Z H H Z Z H H Z Z