sv2 Pi
sv2 Pi
sv2 Pi
SV2-MOVIE
Rev. 4
CompactPCI ® Serial
Carrier for MXM 3.1 Type A/B Graphics Module
SV2-MOVIE • CompactPCI® Serial • Carrier for MXM 3.1 Type A/B Graphics Module
General
The SV2-MOVIE is a peripheral slot board for MXM (Mobile PCI Express Module) is an
PICMG® CompactPCI® Serial systems and interconnect standard for GPUs created by
MXM-SIG. MXM cards are mostly equipped
serves as carrier for an MXM 3.0/3.1 graphics
with an AMD or Nvidia GPU core. With
module. The SV2-MOVIE is provided with four
respect to a reasonable thermal
DisplayPort front panel connectors and can
management, a low power GPU is
2
accommodate either a type A (82x70mm ) or recommended for industrial applications
type B (82x105mm2) MXM graphics module. together with the SV2-MOVIE.
Theory of Operation
For best performance, the SV2-MOVIE should For use with suitable MXM graphics modules,
be operated in a CompactPCI® Serial fat pipe low profile passive heat spreaders are
slot, which provides a PCI Express® x8 host available, for either 4HP or 8HP front panel
interface. The SV2-MOVIE is equipped with a width. In addition, the CompactPCI® Serial
PCIe® Gen3 redriver for optimum signal rack must provide suitable forced airflow (e.g.
integrity. by fans).
Feature Summary
General
< Carrier board for type A or type B MXM 3.0/3.1 graphics module
< Maximum module dimensions 105mm x 82mm x 7mm (type B)
< Maximum module dimensions 113mm x 82mm x 7mm (w/o front panel connectors)
< MXM 3.0 edge card connector 314/281 pins
< PCI Express® Gen3 (8GT/s) redriver on-board, PCIe x8
< Custom cooler plate design (4HP/8HP envelope)
< CUDA (Compute Unified Device Architecture) capable with NVIDIA MXM GPU
< Option +12V external power connector 4.20mm ATX for MXM modules >60W
< Option +12V terminal block 3.5mm Eurostyle for attachment of a 12V DC fan
< Heat spreader available for CoolConduct® technology heat exchanger systems (option)
< NVIDIA® QUADRO® P3000 (6GB DDR5, 1280 CUDA cores, 3.9TFLOPS)
< NVIDIA® QUADRO® P5000 (16GB GDDR5, 2048 CUDA cores, 6.4TFLOPS)
< NVIDIA® QUADRO® Embedded T1000 (4GB GDDR6, 896 CUDA cores, 2.6 TFLOPS)
< NVIDIA® QUADRO® Embedded RTX3000 (6GB GDDR6, 1920 CUDA cores, 5.3TFLOPS)
< NVIDIA® QUADRO® Embedded RTX5000 (16GB GDDR6, 3072 CUDA cores, 9.4TFLOPS)
< Extended/industrial temperature solutions on request
< Coming soon: Ampere Architecture NVIDIA® A1000/2000/4500
For drivers and other software please refer to the MXM module manufacturers website
Regulatory
P6
MXM 3.0 GPU Module Simplified Block Diagram
Type B P5
SV2-MOVIE
MXM Graphics Module
Carrier Backplane
Block Diagram
P4
CompactPCI
Serial
DisplayPort
-6-
1.2/1.3
Fat Pipe
MXM 3.0 Socket PCIe P3
3.0 Slot
Redriver
PCIe
P2
PCIe
P1
Front
Panel
I/O
© EKF
ekf.com
SV2-MOVIE • CompactPCI® Serial • Carrier for MXM 3.1 Type A/B Graphics Module
P6
DP
SV2-MOVIE
Rev. 4
MXM 3.0 Type B
Module Carrier
© EKF • ekf.com
Component Assembly
+12V Power
from SVP
DP Mezzanine
MXM 3.0
MXM 3.0
+12V Power
Type B
A1
Type A
Eurostyle 3.5mm
-7-
1
DP Option
1
+12V
P3
+12V Power
4.20mm
MiniFit Jr.
ATX P2
DP
P1
PV-1
SV2-MOVIE • CompactPCI® Serial • © EKF • ekf.com
© EKF
© EKF
DSW1
ON
12
TH_OVERT
MXM
Status TH_ALERT
LEDs PWR_GOOD
SV2-MOVIE
-8-
Rev. 4
MXM 3.0 Type B
Module Carrier
© EKF • ekf.com
SV2-MOVIE • CompactPCI® Serial • Carrier for MXM 3.1 Type A/B Graphics Module
ekf.com
SV2-MOVIE • CompactPCI® Serial • Carrier for MXM 3.1 Type A/B Graphics Module
Thermal Shutdown
Three signal LEDs are situated at the bottom side of the SV2-MOVIE card, which can be helpful for
system integration, in order to identify potential heat dissipation issues. The LEDs are directly
driven by outputs of the mounted MXM module. The red LED (TH_OVERT#) in addition remains
permanently active after an overtemperature event occurred (edge triggered flip-flop). The red
LED will be switched off not before a system reset.
If an overtemperature situation has been signalled by the MXM module, the main on-board
power regulators of the SV2-MOVIE card will be disabled immediately, in order to prevent the
GPU from damage. The power regulators will remain switched off until a system reset occurs.
yellow
MXM TH_ALERTn *
non critical thermal warning
red
critical temperature event - MXM TH_OVERTn *
power removed until reset
The individual meaning of any signal can vary with the particular MXM module in use. Please refer
to the manufacturers original module documentation for details.
DP
1
DP
3
DP
4
SV2-MOVIE
MXM GPU
Please note: The front handle is provided with a built-in microswitch, which is used to disable the
on-board power circuit when released. Vice versa, the on-board devices are enabled not before the
handle gets locked. Please refer to the illustration below and make sure that the eject lever has
reached its final position for proper board operation, as shown in picture 8. A gentle click should
be audible, when the red actuator pin moves into its raised position, indicating that the board is
locked and ready for use.
1 5
© EKF • ekf.com
2 6
3 7
4 8
1 - 4: remove board
5 - 8: install board
DisplayPort Connectors
The SV2-MOVIE supports up to four independent displays, attached to the front panel display
connectors 1-4. DisplayPort serves as the state of the art interface for computer monitors,
replacing legacy VGA and DVI video connectors since integrated in all main-stream GPUs and
chipsets. The DisplayPort 1.2 specification adds multi-stream transport (MST), allowing up to 63
separate A/V streams across a single DisplayPort connection. Please refer to the MXM Graphics
Module actually in use on the SV2-MOVIE for the number of DP video outputs available,
resolution and other parameters.
For attachment of either a classic style analog RGB monitor or DVI type display to any DP front panel
receptacle, there are both adapters and also adapter cables available, from DisplayPort to the VGA or
DVI connector.
DP • DisplayPort Video
Standard DisplayPort Receptacle, 20-lead (270.60.20.0)
16 GND 15 AUX(P)
20
14 CONFIG2 13 CONFIG1
12 LANE3(N) 11 GND
10 LANE3(P) 9 LANE2(N)
8 GND 7 LANE2(P)
6 LANE1(N) 5 GND
4 LANE1(P) 3 LANE0(N)
2 GND 1 LANE0(P)
Specified by the VESA DisplayPort connector standard is a dedicated power pin 20 (+3.3V 0.5A).
Both the GPU (source side) and a DP monitor (sink side) must provide power via this pin. A VESA
specified DisplayPort cable however must not connect the pins 20 of both cable ends, in order to
avoid a back driving conflict. Unfortunately there are cable assemblies available with pin 20
passed through, with unpredictable results on the system behaviour. Before ordering DP cable
assemblies, verify the associated wiring diagram.
Molex 68783-0007
The SV2-MOVIE is provided with a right angled edge card connector for MXM 3.0/3.1 graphics
modules. If the SV2-MOVIE has been installed into a fat pipe peripheral slot of the CompactPCI®
Serial backplane, a PCI Express® x 8 link is available at the MXM connector. The SV2-MOVIE is
equipped with PCIe Gen3 redrivers (8GT/s) for high performance MXM graphics cards.
The SV2-MOVIE is equipped with 4 DisplayPort front panel connectors 1-4, which are related to
the MXM module DP outputs A, B, C, and D. Please note, that there are MXM modules available
with propriatary (deviant with respect to the MXM specification) output mapping - please refer to
the particular MXM module datasheet for details.
+3.3V is sourced from an on-board regulator. The current should not exceed 3A. +5V is sourced
from an on-board regulator. The current should not exceed 3A. +12V is the main power rail,
passed through from the CompacPCI® Serial backplane connector P1. If the current across the 12V
rail is expected to exceed significantly >5A (>60W MXM module power consumption), the
optional 4.20mm +12V power connector should be employed in addition (in parallel to the
backplane slot P1/J1 12V power pins). All power rails will be disabled if the front panel handle
built-in microswitch has been activated.
External Documents
MXM Graphics Module www.mxm-sig.org
Mobile PCI Express Module Electromechanical Specification Website no longer
Version 3.1 Rev. 1.0 March 1, 2012 available
DSW1
Part #245.35.02.01
By default this switch is set to OFF (I2C circuitry is
1 = OFF Disable enabled and follows geographical addressing
I2C GA schema GA0-GA2)
*
1 = ON If the switch is set to ON, I2C circuitry is disabled
ON
© EKF • ekf.com
160.15.02.0
The VGA_DISABLE# signal can be controlled optionally via an on-board I2C PCA9554A GPIO. In
order to avoid a short circuit condition, slider #2 must be set to off (open) if the GPIO port is
intended to be used as controlling output.
The SV2-MOVIE carrier card derives +12V power via the P1 backplane connector. For an MXM
module with a power consumption >60W, usage of an additional power connector in parallel is
highly recommended. The SV2-MOVIE can be equipped with a 5-pin mezzanine connector, for
attachment of the SVP-POWER mezzanine module as an 8HP assembly. The secondary
CompactPCI® Serial P1 backplane connector doubles the maximum power available up to 120W
in total.
As an alternate, the SVP-POWER can be used as rear I/O module for the SV2-MOVIE, using the rJ3
backplane connector for additional +12V support. This requires a backplane slot configured for
RIO (J3 backplane connector). The additional current is derived from an AMP MATE-N-LOK series
connector, rated at 12A. A suitable power cable harness to the power supply is required in
addition. The SVP-POWER rear I/O solution can be used along with both 4HP and 8HP versions of
the SV2-MOVIE.
As an alternate, the SV2-MOVIE can be equipped with a 2x2 pin 4.2mm pitch dual row wire to
board vertical header (ATX 12V 4-pin), for attachment of a suitable cable assembly between
power supply and the SV2. This would allow up to additional 192W power feeding theoretically.
264.02.104.00
4.20mm Dual Row 2x2
© EKF • ekf.com
GND 1 2 GND
1 2
3 4
+12V 3 4 +12V
Each connector pin is rated at 8A. Mating cable connectors are available e.g. from Molex, under
the Mini-Fit® Jr.™ brand. A suitable housing would be e.g. the Molex part #0039013042, to be
used with crimp terminals e.g. Molex part #0039000060 (18-24 AWG). Other manufacturers for
4.20mm style connectors are e.g. Würth and TE.
The SV2-Movie is available as 4HP or 8HP (or custom size) front panel width assembly, depending
on the heat spreader required for the particular application. The 8HP version would allow for a
straight Mini-Fit® power connector (see picture below).
Another power connector may be provided on the SV2-MOVIE as an option, for attachment of a
12V DC compact fan mounted above the MXM cooling plate (typically 8HP SV2-MOVIE front
panel width assembly).
GND 2 1 +12V
2 1
The 3.50mm pitch vertical header mates with a suitable plug e.g. Molex part #0395073002. Other
Eurostyle compatible terminal block suppliers are e.g. Phoenix Contact, Weidmüller, Würth, TE, or
FCI. As an alternate, the pig tail wires of the cooling fan can be soldered directly to the SV2-MOVIE
PCB, using the 3.50mm connector terminal pads. Since both connectors, the 4.20mm ATX and the
3.50mm terminal block are wired in parallel on-board to +12V (in addition to the power pins of
the backplane connector P1), the terminal block can also be used for external power supply up to
8A, as an alternate.
P2 A B C D E F G H I J K L
8 GND GND GND GND
PE PE PE PE PE PE PE PE
2 GND
TX06+ TX06-
GND
RX06+ RX06-
GND
TX07+ TX07-
GND
RX07+ RX07-
PE PE PE PE PE PE PE PE
1 TX04+ TX04-
GND
RX04+ RX04-
GND
TX05+ TX05-
GND
RX05+ RX05-
GND
P1 A B C D E F G H I J K L
PE PE PE PE PE PE PE PE
6 GND
TX02+ TX02-
GND
RX02+ RX02-
GND
TX03+ TX03-
GND
RX03+ RX03-
PE PE PE PE PE PE PE PE
5 TX00+ TX00-
GND
RX00+ RX00-
GND
TX01+ TX01-
GND
RX01+ RX01-
GND
1 +12V STBY GND +12V +12V GND +12V +12V GND +12V +12V GND
P3 A B C D E F G H I J K L
8 GND GND GND GND
7 +12V GND +12V +12V GND +12V +12V GND +12V +12V GND
5 +12V GND +12V +12V GND +12V +12V GND +12V +12V GND
3 +12V GND +12V +12V GND +12V +12V GND +12V +12V GND
1 +12V GND +12V +12V GND +12V +12V GND +12V +12V GND
From Rev. 2 PCB off, additional +12V power can be supplied via P3 by means of a custom specific
backplane. Please note, that the SV2-MOVIE must not be inserted into a backplane slot which is
wired for propriatary rear I/O on these pins, due to backdriving +12V power from P1 to P3.
The SV2-MOVIE is suitable for modest parallel computing when equipped with a CUDA capable
graphics module (NVIDIA). For details please refer to www.nvidia.com.
SV2-MOVIE Links
SV2-MOVIE Home https://www.ekf.com/s/sv2/sv2.html
Ordering Information
For popular SV2-MOVIE SKUs please refer to
https://www.ekf.com/liste/liste_21.html#SV2
CoolConduct® Skids
CoolConduct® System