TS-2000 (B510-01-005) UT-20 Installation
TS-2000 (B510-01-005) UT-20 Installation
TS-2000 (B510-01-005) UT-20 Installation
KENWOOD CORPORATION
CAUSE:
TX-RX 3 UNIT
G13-1878-05 (X57-607)
Foil side view
Soldering
Attach to the PCB
A2
5
A2
6
G13-1877-05 G13-1877-05
G13-1878-05 G13-1877-05
Attach to L42
Attach to the shelding and CN9
case (A1) Attach to L28
Attach to L52 and L29
8
L2
2
L4
9
CN
L
2
9
SERVICE TECHNICAL REPORT
KENWOOD CORPORATION
Installation Procedure
1. Remove the upper and lower cases of the main unit. 4. Install a lead (2 pins) with a connector, which is supplied
2. Remove the 2 screws holding the main unit. Remove with the UT-20, on the UT-20 connector (CN1), and pass
the rear shield plate ( 1 ). the other lead and the lead with a terminal through a
3. Remove the 2 screws holding the lead with a terminal hole in the chassis ( 3 ).
( 2 ). Guide the lead with a terminal so that it runs through
between the dielectric filters (L30 and L33). When
mouting the 1200MHz unit to the chassis, make sure a
1 wire harness band that is securing the lead with a termi-
nal together, is located under the 1200MHz unit. In this
way, the wire harness band can act as a stopper ( 4 ).
5. Install the UT-20 on the main unit, and tighten 10
screws ( 5 ).
6. Tighten the UT-20 lead with a terminal and the lead with
a terminal from the final (430) unit (X45-360 B/2) with 2
screws ( 6 ).
7. Install the UT-20 lead with a connector (2 pins) and in-
stall the lead with a connector (2 pins) and the EXT AT
connector wire using a wire harness band ( 7 ).
8. Install one end of the UT-20 flat cable on the UT-20 con-
nector (CN6) ( 8 ).
9. Pass the ends of the supplied coaxial cable and the lead
with a connector (4 pins) through the hole in the chas-
sis, and install them on the UT-20 connectors (CN9 and
CN5) ( 9 ).
10. Install the coaxial cable and lead with a connector (4
pins) using a wire harness band ( 10 ).
11. Route the coaxial cable and lead with a connector (4
pins) on the side of the chassis in an L shape, then pull
them toward the bottom of the main unit ( 11 ).
12. Fix the coaxial cable and lead with a connector (4 pins)
near CN27 of the TX-RX1 (HF/IF) unit (X57-605 A/9) us-
ing a wire harness band ( 12 ).
13. Place the coaxial cable and lead with a connector (4
pins) on the side of the chassis, pass them behind the
connector (CN27) of the TX-RX1 (HF/IF) unit (X57-605 A/
2 9), and under the flat cable connected to the connector
(CN26) of the TX-RX1 (HF/IF) unit (X57-605 A/9). Then,
pass them between the electrolytic capacitor (C553)
and connector (W2) ( 13 ).
After routing as above, install the UT-20 flat cable on the
connector (CN27) of the TX-RX1 (HF/IF) unit (X57-605 A/
9). (When routing the cable and lead, the coaxial cable
and lead with a connector must not approach the fan.)
14. Install the coaxial cable and lead with a connector (4
pins) using a wire harness band ( 14 ).
15. Install the coaxial cable and lead with a connector (4
pins) on the connectors (CN22 and CN11) of the TX-RX1
(HF/IF) unit (X57-605 A/9) ( 15 ).
16. Install the UT-20 shield plate and tighten the 11 screws
( 16 ).
17. Install the fitting on the main unit and tighten the 2
screws ( 17 ).
18. Install the upper and lower cases of the main unit.
16
11 4
L33
CN5 L30
CN9
17
Approx. 9
60mm
9
10
3
8 CN5
CN26 12
13 W 2 5
C553
CN1
Approx. 70mm
14
CN27 7
6
15
CN11 CN22
Approx.
70mm
7
SERVICE TECHNICAL REPORT
KENWOOD CORPORATION
3. 1.2G SSB 1) Menu No. : 52 SSG Rear ANT1.2G Front [+] key Change the adjust-
IF gain Display f. : 1270.20MHz panel panel or ment values within
(AGC start Mode : USB [–] key the range of 1 to 5
level) AGC : ON on the display.
RF GAIN : MAX
SSG output : –116dBm/0.35µV
4. 1.2G SSB 1) Menu No. : 53 SSG Rear ANT1.2G Front [+] key 1 push S-meter lights up to
S-meter Display f. : 1270.20MHz panel panel or S1 level.
S1 Mode : USB AF V.M EXT. SP [–] key
SSG f. : 1270.20MHz Oscilloscope
SSG output : –113dBm/0.501µV DM. SP
3. 1.2G 1) Menu No. : 109 Power meter Rear ANT1.2G Front [+] key Set the adjustment 10W± 0.1W
power POC Display f. : 1270.10MHz panel panel or value within the
10W Mode : USB [–] key limit of the specified
Transmit power.
6. 1.2G 1) Menu No. : 123 DC V.M TX-RX1 CN27 Check the default 0.1 to 1.0V
protection Display f. : 1270.10MHz (A/9) (12VSR) voltage (Vo).
Mode : CW
ANT : 50Ωdummy load
Set the adjustment value to 0.
Transmit
2) Menu No. : 123 [+] key Set the adjustment Vo+(0.68 to 0.72V)
Display f. : 1270.10MHz or value within the
Mode : CW [–] key limit of the specified
ANT : Open voltage.
Set the adjustment value
to 100.
Transmit