Allen Bradley Catalog Wiring Systems
Allen Bradley Catalog Wiring Systems
Allen Bradley Catalog Wiring Systems
BULLETIN 1492
Digital/Analog Programmable Controller Wiring Systems
CATALOG NUMBER 1492 Benefits Digital (IFM/XIM and Cables) Analog (AIFM and Cables) Ordering Digital and Analog Wiring Systems Selection Tables Specifications Dimensions Marking Systems Accessories Web Site Information Quick Reference 3 6 22 29 30 66 175 176 179 181 182
Description
Connecting to Allen-Bradley PLC I/O modules is convenient with Allen-Bradley Interface Modules and Cables. Unlike conventional terminal blocks, they connect through pre-wired cables to digital and analog I/O for the Bulletin 1746 SLC, Bulletin 1756 ControlLogix, Bulletin 1769 Compact I/O for CompactLogix and MicroLogix 1500, and Bulletin 1771/PLC-5 platforms. The interface modules are mounted onto a standard DIN #3 Rail. Pre-printed adhesive label cards containing field-wiring information are included for each interface module and I/O module combination. Wiring systems are available for over 100 digital I/O modules and over 40 analog I/O modules.
Benefits
Benefits, Continued
Simplified Design
Design engineers can simplify their panel drawings by calling out an IFM and pre-wired cable instead of having to detail every single wire and terminal block on their drawings. Simplified panel drawings aid both the installer and the end user who receives the panel.
Benefits, Continued
Quality-Looking Panels
The pre-wired cables and IFM wiring system modules organize the wiring in your panel and provide a consistent look. Pre-printed adhesive labels for the terminals neatly identify field-wiring connections, which correspond to the I/O module address. A large marking area is also available for identifying I/O information on the IFM.
Design Flexibility
To develop a cost-effective system, the hardware components must meet the needs of the design engineer. Rockwell Automation provides the broadest range of digital and analog systems in the industry. Allen-Bradley Wiring Systems deliver a lower life-cycle cost.
Digital IFMs, similar to groups of terminal blocks, are available with either 20-pin (typically 8 to 16 PLC I/O points) or 40-pin (typically 16 to 32 PLC I/O points) cable connectors. The number of field-side wiring terminals varies with the type of module from one to three terminals per I/O point. LEDs and fuse clips are available on-board the IFMs to customize your wiring system to your application and provide assistance with troubleshooting your control panel. The IFMs are compatible with both the pre-wired cables and the IFM-ready cables. All of the digital IFMs have the following features:
UL Recognized Component (File E113724 Guide NRAQ2); CSA Certification: (File LR1234-881 Class 3211-07); CE Certified; Factory Mutual Listed (File J.I. 3000590) FM approved, Class 1 Div 2 (except relay outputs).
Pre-printed and blank adhesive marking strips are provided to identify either Programmable Controller I/O field-side wiring terminals or your own application requirements.
Keyed cable connector (20- or 40-pin) with locking tabs for easy installation and secure connection of IFM pre-wired and IFM-ready cables.
High-density field-side wiring terminals allow more connections in less space and accommodate #2212 AWG wire.
Continuous current rating of 2 A per circuit supports higher-current programmable controller output modules.
Standard terminal IFM modules provide one field-side wiring terminal per programmable controller input or output point, as well as enough terminals for the I/O module power connections. The standard terminal modules are ideal for applications in which the I/O device commons are terminated in the field or remotely from the I/O module panel.
Extra terminal modules provide two or four field-side terminals per input or output point. IFMs which are not point-to-point isolated have two terminals per input or output point. Point-to-point isolated IFMs have two or four terminals per input or output point. Non-isolated IFMs have the lower row of extra terminals commoned together in groups of 10 , to serve as a power bus for the field device commons. Isolated IFMs have terminals isolated into 8 or 16 groups, which allows each group of I/O devices to reference a different power source. The extra terminal modules are beneficial in applications in which the I/O devices are terminated within the same panel as the I/O modules eliminating the need for many additional terminal blocks. These modules are also available with optional field-side status LEDs for troubleshooting inputs and outputs.
Except Catalog Numbers 1492-IFM20D24A-2 and -IFM20D120A-2, which are in groups of 20.
Sensor Modules
Sensor modules provide three field-side terminals per input point. The middle and lower rows of terminals, commoned together in groups of 18, serve as power busses for 3-wire sensor types of devices eliminating additional terminal blocks and jumpering systems. The sensor modules provide a compact method of terminating and powering 24V AC/DC or 120V AC (Catalog Number IFM20F-3 only) 3-wire devices.
LED Modules
Voltage-indicating LEDs are available on the standard, extra terminal, and sensor IFMs. The LEDs provide field-side troubleshooting diagnostics: the on/off status of an input device or the on/off status of the programmable controller output circuit. When used in conjunction with the logic-side programmable controller LEDs, the IFM LEDs can help determine whether a problem resides in the I/O module or field device/wiring. The LED modules have unique circuitry that allows compatibility with sinking or sourcing input or output modules.
Fusible Modules
Fusible modules provide a convenient method of adding overcurrent protection into your programmable controller field wiring. These modules have 5 x 20 mm fuse clips on-board and are available with and without blown fuse indication. The 24V or 120V blown fuse indicators reduce the troubleshooting time to locate and replace a blown fuse on the IFM. The fusible modules have an easy-to-remove see-through acrylic cover to prevent objects from contacting fuse circuitry under normal operation. Standard fuse holders reside in the IFM, aiding in the removal of a fuse with a fuse puller (fuses are not included). The fusible modules also have two or four terminals per I/O point to create a power bus for input or output load connections. Fusible modules are available in both isolated and non-isolated versions. There are a select number of fusible IFMs available for input modules.
10
Relay master XIMs feature field-replaceable relays with 120V or 24V rated coils. The field-side Form C contacts are rated 240V 10 A (de-rated to 12 A per adjacent pair on the XIM). The Form C relay output provides isolated output channels and a different voltage level from one output channel to the next. Other features include coil-side LED indicating the PLC output module status, and transient suppression on each coil. In addition, 16-point relay masters are available with or without 5x20 fuse holders so customers can fuse the output contacts.
Relay Expanders
Relay expander XIMs feature eight field-replaceable relays with 120V or 24V rated coils. The field-side Form C contacts are rated 240V 10 A (de-rated to 12 A per adjacent pair on the XIM). The Form C relay output provides isolated output channels and a different voltage level from one output channel to the next. Other features include coil-side LED indicating the PLC output module status, and transient suppression on each coil. In addition, a relay expander can have 5 x 20 fuse holders so customers can fuse the output contacts. An expander cable is provided for connection to the mating module.
Publication 1492-TD008C-EN-P - September 2005
11
The fusible expander modules feature eight 5 x 20 mm finger-safe fuse holders, blown fuse indicators, and extra terminals for landing two wires per field-side device. They are offered with eight fuse holders for both 24V and 120V applications. An expander cable is provided for connection to the mating module. Fuses are not provided.
Feed-Through Expanders
The feed-through expander modules feature eight channels with extra terminals for landing two wires per field-side device. An expander cable is provided for connection to the mating module.
12
shipped with the RTB socket, but without the removable plug(s). Plugs are available with screw style or push-in style (March 2006) terminals and must be ordered separately. Refer to the Selection Tables for the particular PLC I/O system of interest to determine which modules are offered with field Removable Terminal Blocks. All of the features available on fixed terminal block products (e.g. labels, agency certification, etc.) are also provided for the removable terminal block 1492 wiring system modules.
RTB Socket
RTB Plug
(Order Separately)
13
Bulletin 1492 pre-wired cables are designed to minimize control wiring in a panel. Pre-wired cables, when used with an IFM, replace the point-to-point wiring between Allen-Bradley programmable controller I/O modules and individual terminal blocks. The pre-wired cables have a removable terminal block or wiring arm at the I/O end of the cable and a cable connector on the other end to connect to the IFM. All of the pre-wired cables use #22 AWG wire and are 100% tested for continuity to make a perfect connection every time. The digital pre-wired cables are offered in four standard lengths of 0.5, 1.0, 2.5, and 5.0 m to fit a variety of applications. Other cable lengths are also available as build-to-order products. Pre-wired cables are available for many of the 1746 SLC I/O, 1756 ControlLogix I/O, 1769 Compact I/O for CompactLogix and MicroLogix 1500, and 1771 PLC-5 I/O controllers.
Digital I/O module-ready cables have an I/O removable terminal block or wiring arm pre-wired to one end to of the cable and free connectors on the other end for wiring into standard terminal blocks or other type of connectors. I/O-ready cables have individual color-coded conductors for quick wire-toterminal coordination. The I/O-ready cables use #18 AWG conductors for higher current applications or longer cable runs. The I/O-ready cables are offered in standard lengths of 1.0, 2.5, and 5.0 m to fit a variety of applications. Other cable lengths are also available as build-to-order products. Pre-wired cables are available for the Bulletin 1746 SLC I/O, Bulletin 1756 ControlLogix I/O, Bulletin 1769 Compact I/O for CompactLogix and MicroLogix 1500, and Bulletin 1771 PLC-5 I/O controllers.
Publication 1492-TD008C-EN-P - September 2005
14
IFM-ready cables have a cable connector that attaches to the IFM pre-wired to one end and free connectors ready to wire to I/O modules or other components on the other end. IFM-ready cables use #22 AWG wire and have individual color-coded conductors for quick wire-to-terminal coordination. The digital IFM-ready cables are offered in standard lengths of 1.0, 2.5, and 5.0 m to fit a variety of applications. Other cable lengths are also available as build-to-order products.
15
Important: The following IFM catalog number breakdown is for explanation purposes only. It is not a product configurator. Not all combinations of fields are valid product catalog numbers. First, select the desired IFM using the steps in Ordering Digital and Analog Wiring Systems on page 29. Then, use this breakdown for verification and explanation only.
Status Indication F No LEDs FN Narrow IFM D24 24V AC/DC LEDs for input and output modules D24N Narrow IFM with 24V AC/DC LEDs D24A 24V AC/DC LEDs for input modules DS24 Isolated IFM with 24/48V AC/DC LEDs for output modules DS24A Isolated IFM with 24V AC/DC LEDs for input modules D120 120V AC LEDs for input and output modules D120N Narrow IFM with 120V AC LEDs D120A 120V AC LEDs for input modules DS120 Isolated IFM with 120V AC LEDs for output modules DS120A Isolated IFM with 120V AC LEDs for input modules D240 240V AC LEDs for output modules DS240A Isolated IFM with 240V AC LEDs for input modules D240A 240V AC LEDs for input modules
Fuses and Their Indicators Blank No fuse clips F 5 x 20 mm fuse clips F24 5 x 20 mm fuse clips with 24V blown fuse indicators for output modules F24A 5 x 20 mm fuse clips with 24V blown fuse indicators for input modules F120 5 x 20 mm fuse clips with 120V blown fuse indicators for output modules F120A 5 x 20 mm fuse clips with 120V blown fuse indicators for input modules F240 5 x 20 mm fuse clips with 240V blown fuse indicators for output modules F24D-2 5 x 20 mm fuse clips with 24V blown fuse low leakage indicators for the 1756-OB16D diagnostic output module F24AD-4 5 x 20 mm fuse clips with 24V blown fuse low leakage indicators for the 1756-IB16D diagnostic input module FS Isolated IFM with 5 x 20 mm fuse clips FS24 Isolated IFM with 5 x 20 mm fuse clips with 24V blown fuse indicators for output modules FS24A Isolated IFM with 5 x 20 mm fuse clips with 24V blown fuse indicators for input modules FS120 Isolated IFM with 5 x 20 mm fuse clips with 120V blown fuse indicators for output modules FS120A Isolated IFM with 5 x 20 mm fuse clips with 120V blown fuse indication for input modules FS240 Isolated IFM with 5 x 20 mm fuse clips with 240V blown fuse indication for output modules
16
Relay master and expander XIMs are available for Bulletin 1746, 1756, 1769, and 1771 digital output modules. Relay Master XIM Provides 8 or 16 relay outputs for a digital output module. Expander XIM In addition to the relay master XIM, an expander XIM provides eight or sixteen additional outputs. There are five types of expander XIMs: eight-channel relays, eight-channel fusing, and eight-channel feedthrough XIMs.
Relay Master/Expander XIMs Catalog Number Explanation for Digital I/O Modules
Important: The following XIM catalog number breakdown is for explanation purposes only. It is not a product configurator. Not all combinations of fields are valid product catalog numbers First, select the desired XIM using the steps in Ordering Digital and Analog Wiring Systems on page 29. Then, use this breakdown for verification and explanation only.
1492 XIM 20 24 2
Bulletin No. No. Relays or Extra Terminals 2 2 terminals per point 8R 8 relays 16R 16 relays 16RF 16 fused relays
Relay Master and Expander Interface Modules XIM Fixed (non-removable) terminal block RXIM Removable terminal block
No. Cable Connector Pins 20 20 pins (master only) 40 40 pins (master only) Blank Expander module
Rating of Relay Coil or Blown Fuse Indicator 24 24V relay coil 120 120V relay coil F No relays or fuses F-F24 5 x 20 mm fuse clips with 24V blown fuse indicators F-F120 5 x 20 mm fuse clips with 120V blown fuse indicators
17
Important: The following RTB plug catalog number breakdown is for explanation only.
1492 RTB 20 N
Bulletin No. Connector Style N Screw Style P Push-in Style
18
IFM and XIM Cable Catalog Number Explanation for Digital I/O Modules
Important: Use the following tables as a product configurator for pre-wired, IFM-ready, and I/O module-ready cables for Bulletins 1746, 1756, and 1771 digital I/O module cables. All combinations of these fields make valid product catalog numbers. Refer to selection tables for IFM/XIM compatibility and ordering.
Standard or Build-to-Order Length Cable 005 0.5 m (1.64 ft) Standard Length 010 1.0 m (3.28 ft) 025 2.5 m (8.20 ft) 050 5.0 m (16.40 ft) 001 0.12.0 m (0.3286.56 ft) Build-to-Order 020 0.1 m (0.328 ft) increments Length 020 2.010.0 m (6.5632.8 ft) 100 0.5 m (1.64 ft) increments 100 10.099.0 m (32.8374.72 ft) 990 1.0 m (3.28 ft) increments
Pre-wired cables for 8-point isolated and 16-point digital Bulletin 1746 I/O modules Pre-wired cable for Catalog Number 1746-OA16 (XIM only) Pre-wired cable for digital Bulletin 1771 I/O modules Pre-wired cable with fused wiring arm for 16-point digital Bulletin 1771 output modules H Pre-wired cable for 32-point digital Bulletin 1746 I/O modules J, K, L, M, R Pre-wired cables for 16-point isolated and 32-point digital Bulletin 1771 I/O modules U, V, W, X Pre-wired cables for 8- and 16-point digital Bulletin 1756 I/O modules Y, Z Pre-wired cables for 16-point isolated and 32-point digital Bulletin 1756 I/O modules P Digital IFM-ready cable with 20 conductors Q Digital IFM-ready cable with 40 conductors N3 Digital I/O module-ready cable with 40-point Catalog Number 1746-N3 cable connector RTBB Digital I/O module-ready cable with 16-point Catalog Number 1746-RT25B terminal block (blue) RTBO Digital I/O module-ready cable with 16-point Catalog Number 1746-RT25C terminal block (orange) RTBR Digital I/O module-ready cable with 16-point Catalog Number 1746-RT25R terminal block (red) TBCH Digital I/O module-ready cable with 36-pin Catalog Number 1756-TBCH removable terminal block TBNH Digital I/O module-ready cable with 20-pin Catalog Number 1756-TBNH removable terminal block WA Digital I/O module-ready cable with Catalog Number 1771-WA 8-point wiring arm WD Digital I/O module-ready cable with Catalog Number 1771-WD 6-point wiring arm WH Digital I/O module-ready cable with Catalog Number 1771-WH 16-point wiring arm WHF Digital I/O module-ready cable with Catalog Number 1771-WHF 16-point fused wiring arm WN Digital I/O module-ready cable with Catalog Number 1771-WN 32-point wiring arm
To make sure the Bulletin 1746 SLC 500 digital I/O module is compatible with the IFM/XIM, refer to pages 31, 33, and 35. To make sure the Bulletin 1771 PLC digital I/O module is compatible with the IFM/XIM, refer to pages 57, 59, and 61. To make sure the Bulletin 1756 ControlLogix digital I/O module is compatible with the IFM/XIM, refer to pages 38, 40, and 42.
The cables used for Relay Master/Expander XIMs are the same as those used for Digital I/O Modules (page 29) with the exception of the Catalog Number 1746-OA16 output module, which uses the 1492-CABLE*CR cable.
19
IFM and XIM Cable Catalog Number Explanation for Digital I/O Modules, Continued
Important: Use the following tables as a product configurator for pre-wired, IFM-ready, and I/O module-ready cables for Bulletins 1769 digital I/O module cables. All combinations of these fields make valid product catalog number. Refer to selection tables for IFM/XIM compatibility and ordering.
Digital Interface Cable Standard or Build-to-Order Length Cable 005 0.5 m (1.64 ft) 010 1.0 m (3.28 ft) 025 2.5 m (8.20 ft) 050 5.0 m (16.40 ft) 001-020 0.12.0 m (0.3286.56 ft) 0.1 m (0.328 ft increments) 020-100 2.010.0 m (6.5632.8 ft) 0.5 m (1.64 ft) increments 100-990 10.099.0 m (32.8374.72 ft) 1.0 m (3.28 ft) increments
Standard Length
Build-to-Order Length
20
Cable Catalog Number Explanation for 1200 Base I/O to IFM Modules
Important: Use the following tables as a product configurator for pre-wired, and I/O module-ready cables for Bulletin 1762 MicroLogix 1200 40 I/O controller digital I/O cables. All combinations of these fields make valid product catalog numbers. Refer to selection tables for IFM compatibility and ordering.
1492 CAB
Bulletin No. Cable Type A62, B62 X62 T62 Standard or Build-to-Order Length Cable 005 0.5 m (1.64 ft) Standard Length 010 1.0 m (3.28 ft) 025 2.5 m (8.20 ft) 050 5.0 m (16.40 ft) 001 0.12.0 m (0.3286.56 ft) Build-to-Order 020 0.1 m (0.328 ft) increments Length 020 2.010.0 m (6.5632.8 ft) 100 0.5 m (1.64 ft) increments 100 10.099.0 m (32.8374.72 ft) 990 1.0 m (3.28 ft) increments
010 A62
Pre-wired cables for Bulletin 1762 40 I/O controllers I/O-ready cable for 1762-L40AWA, -L40BXB, and -L40BWA inputs I/O-ready cable for 1762-L40AWA, -L40BXB and -L40BWA outputs
21
Cable Catalog Number Explanation for 1500 Base I/O to IFM Modules
Important: Use the following tables as a product configurator for pre-wired, and I/O module-ready cables for Bulletins 1764 MicroLogix 1500 base unit digital I/O cables. All combinations of these fields make valid product catalog number. Refer to selection tables for IFM compatibility and ordering.
Digital Interface Cable Standard or Build-to-Order Length Cable 005 0.5 m (1.64 ft) 010 1.0 m (3.28 ft) 025 2.5 m (8.20 ft) 050 5.0 m (16.40 ft) 001-020 0.12.0 m (0.3286.56 ft) 0.1 m (0.328 ft increments) 020-100 2.010.0 m (6.5632.8 ft) 0.5 m (1.64 ft) increments 100-990 10.099.0 m (32.8374.72 ft) 1.0 m (3.28 ft) increments
Pre-wired cables for Bulletin 1764 I/O base units I/O-ready cable for 1764-24AWA, -24BWA base unit inputs I/O-ready cable 1764-28BXB base unit inputs I/O-ready cable for1764-24AWA, -24BWA base unit outputs I/O-ready cable for 1764-28BXB base unit outputs
22
Analog IFMs (AIFMs), similar to groups of terminal blocks, are available with either 15- or 25-pin D-shell connectors. The number of field-side wiring terminals varies with the type of module from three to five terminals per analog I/O channel. AIFMs are available as feed-through or fusible to customize the wiring system to your application. All of the AIFMs have the following features:
Polarized D-shell connector (15- or 25-pin) for easy installation. Pre-wired cable has mating D-shell connector with slide-locking mechanism for secure connection.
Pre-printed and blank adhesive marking strips are provided to identify either Programmable Controller I/O field-side wiring terminals or your own application requirements.
UL Recognized Component (File E113724 Guide NRAQ2); CSA Certification: (File LR1234, Class 3211-07); CE Certified; Factory Mutual Listed (File J.I. 3000590) FM approved, Class I Div 2.
High-density field-side wiring terminals allow more connections in less space and accommodate #2212 AWG wire.
Continuous current rating of 2 A per circuit supports higher-current programmable controller output modules. Analog IFM
23
Feed-through AIFMs have three terminals per analog I/O channel to wire the analog I/O device connections and shield. The shield terminals are internally bussed together and also tied to the D-shell housing to connect with the 1492 cable shield and back to the PLC module. Some feed-through AIFMs also have special features (refer to page 23). The Catalog Number 1492-AIFM4-3 AIFM, when used with Catalog Numbers 1771-OFE2 and -OFE3 controllers, provides selectable current limiting resistors. Simply flip a DIP switch to add the 250 ohms series impedance into the output circuit. As a troubleshooting aid, test point loops access the circuit on either side of the series resistor and can be used to measure output circuit voltage/current. The limiting resistors are configured on a per channel basis. The Catalog Number 1492-AIFM6TC-3 AIFM for the Catalog Number 1756-IT6I controller provides on-board cold junction compensation to allow thermocouples to be connected remotely while still correcting for temperature at the termination point. The combination thermistor and isothermal bar acquires temperature data at the AIFM for the thermocouple module to adjust the input value. The Catalog Number 1492-AIFM8-3 AIFM has eight extra terminals commoned together in a power bus that can be used for Module Common connections or power supply connections. The extra terminals and internal jumpering eliminate the need for some terminal blocks for power connections and jumper accessories. Below are examples of the field-side connections available on the feed-through AIFMs.
Output
AIFM 0 LOAD Pre-wired Cable OUT 0 C ANL COM SH Analog Output Module
24
Fusible AIFMs are available for analog input modules. These AIFMs enable you to fuse the input device power source on the field-side. The field-side power source is distributed through individual on-board 5 x 20 mm fuse clips. The fused AIFMs have 24V DC blown fuse indicators to reduce the troubleshooting time needed to locate and replace a blown fuse. The fuse holder has an integrated fuse puller to simplify fuse removal. Isolation switch plugs or dummy fuses (refer to Accessories, page 198) are also available to isolate an input circuit after power is removed. In addition, once the circuit has been isolated and power restored, the input loop current can be measured in 2-wire transmitter applications. The fusible AIFMs have five terminals per input channel (except Catalog Number AIFM16-F-3, which has three terminals per channel) to wire the input-device connections, device shield, and power connections for 2-, 3-, and 4-wire transmitters. The shield terminals are internally bussed together and also tied to the D-shell housing to connect with the 1492 cable shield and back to the PLC module. There are two separate power busses (416 terminals, depending on the AIFM) that can be used for +V and DC COM connections and/or device Common. The extra terminals and internal connections eliminate additional terminal blocks and jumpers reducing spare parts inventory, saving panel space, and simplifying installation. Several of the fusible AIFMs have on-board DIP switches to easily connect unused inputs to module common reducing wiring on the field-side. You no longer need extra jumper wires or comb-style jumpers to properly terminate unused inputs, as recommended on many Bulletin 1746, 1756, and 1771 analog input modules. Inputs are jumpered via DIP switch on a perchannel basis. The Catalog Numbers 1492-AIFM4I-F-5 and 1492-AIFM4C-F-5 AIFMs both have test point loops on either side of the fuse clips for easier access and connection of metering equipment. Metering equipment can also be attached to the fuse clips on other AIFMs for measuring input loop current.
25
Note: 1492 module wiring diagrams are available at www.ab.com. Refer to page 180.
26
the RTB socket, but without the removable plug(s). Plugs are available with screw style or push-in style (March 2006) terminals and must be ordered separately. Refer to the Selection Tables for the particular PLC I/O system of interest to determine which modules are offered with field Removable Terminals Blocks. All of the features available on analog fixed terminal block products (e.g. labels, agency certification, etc.) are also provided for the removable terminal block 14092 wiring system modules.
RTB Socket
Important: The following AIFM catalog number breakdown is for explanation purposes only. It is not a product configurator. Not all combinations of fields are valid product catalog numbers First, select the desired AIFM using the steps in Ordering Digital and Analog Wiring Systems on page 29. Then, use this breakdown for verification and explanation only.
27
1492 AIFM 16 F 5
Bulletin No. No. Field-Side Wiring Terminals 3 3 per I/O channel 5 5 per input channel
Analog Interface Modules AIFM Fixed (non-removable) terminal block RAIMF Removable terminal block
No. Analog I/O Channels 4 4 channels: input, output, or 2 input/output combination 4C 4 channels: 2 input/2 output combination 4I 4 input channels 6S 6 isolated input or output channels 6TC 6 thermocouple input channels 8 8 input or output channels 16 16 input channels PI 8 input/2 output channels
Input Fuse Clips and Blown Fuse Indicators Blank No fuse clips F 5 x 20 mm fuse clips with 24V DC blown fuse indicators for output modules
28
Pre-Wired Cable Catalog Number Explanation for Bulletins 1746, 1756, and 1771 Analog I/O Modules
Bulletin No.
Important: The following analog cable catalog number breakdown is for explanation purposes only. It is not a product configurator. All combinations of fields are not valid product catalog numbers. First, select the desired AIFM using the steps in Ordering Digital and Analog Wiring Systems on page 29. Then, use this breakdown for verification and explanation only.
Analog Interface Cables Standard or Build-to-Order Length Cable 005 0.5 m (1.64 ft) 010 1.0 m (3.28 ft) 025 2.5 m (8.20 ft) 050 5.0 m (16.40 ft) 001-020 0.12.0 m (0.3286.56 ft) 0.1 m (0.328 ft increments) 020-100 2.010.0 m (6.5632.8 ft) 0.5 m (1.64 ft) increments 100-990 10.099.0 m (32.8374.72 ft) 1.0 m (3.28 ft) increments
Standard Length
Build-to-Order Length
A-Cable Type A, B, C, D, Pre-wired cables for Bulletin 1746 analog I/O and L, Q, R, A46 RTD input modules. E, F, G, H, J Pre-wired cables for Bulletin 1771 analog I/O and RTD input modules. TA, TB, TC, Pre-wired cables for Bulletin 1756 analog I/O, RTD, TD, UA, UB, and thermocouple input modules. UC, UD, VA, VB, WA, WB, X, Y, Z YT Pre-wired cable for bulletin 1756-IT6I2 thermocouple input Module. M Pre-wired cables for Bulletin 1757 pulse input module.
Pre-Wired Cable Catalog Number Explanation for Bulletin 1746 and 1769 Analog I/O Modules
Important: The following analog cable catalog number breakdown is for explanation purposes only. It is not a product configurator. All combinations of fields are not valid product catalog numbers. First, select the desired AIFM using the steps in Ordering Digital and Analog Wiring Systems on page 29. Then, use this breakdown for verification and explanation only.
Pre-wired cables for Bulletin 1746-NI16I and -NI16V analog modules. Pre-wired cables for Bulletin 1769 analog I/O modules and RTD input module.
Build-to-Order Length
29
To order the proper IFM/XIM/AIFM pre-wired cable: 1. Determine the PLC I/O platform (e.g., Bulletin 1746, 1756, 1769, 1771) you are using and the catalog number of the I/O module being specified (e.g., 1746-IB16). 2. Determine whether you require field-side LEDs, fusing for over-current protection, or relays (check voltage ratings for LEDs, fuse blown indication, relay, and coil voltage). 3. Determine your field-side wiring requirements. Are extra terminals needed? 4. Determine your desired PLC I/O module to IFM/XIM/AIFM cable length (0.5 m, 1.0 m, 2.5 m, 5.0 m, or build-to-order) based on wiring needs. 5. Refer to selection tables as follows:
Selection Table Quick Reference Platform Bulletin 1746 Digital (IFM/XIM) Bulletin 1746 Analog (AIFM) Bulletin 1756 Digital (IFM/XIM) Bulletin 1756 Analog (AIFM) Bulletin 1769 Digital (IFM/XIM) Bulletin 1769 Analog (AIFM) Bulletin 1771 Digital (IFM/XIM) Bulletin 1771 Analog (AIFM) Page No. 31 36 38 43 49 54 57 62
30
Selection Tables
Using Bulletin 1746 Selection Tables to Make Valid 1492 Wiring System Module Catalog Numbers
Follow these steps when using the selection tables to make valid catalog numbers: 1. Find the appropriate table based on the catalog numbers of the 1746 I/O module. 2. Find the column for the 1746 I/O module. 3. Follow the column down to determine which Wiring Systems Modules are compatible with the I/O module as indicated by letter code. If there is no letter code, the 1492 Wiring System Module is not compatible with the I/O module. NOTE: The letter codes designate the compatible 1492 cable for that 1746 I/O and 1492 Wiring System Module combination. 4. Select the desired 1492 Wiring System Module. 5. Configure the cable catalog number using 1492-CABLE (for digital cables) or 1492-ACABLE (for analog cables). See footnote on pages 35 and 36.
31
Feed-through Standard 264V AC/DC Max. 1492-IFM20F 1492-RIFM20F 1492-RIFM20FN 1492-RIFM20F-2 A A A A B B B B B B B B E E E E B B B B A A B B B B B B B B B B B B B B B B C G C E E E E E E E E E E E E E E E E E E D N D N A A B B Narrow standard132V AC/DC 1492-IFM20FN Max. Extra terminals (2 per I/O) 264V AC/DC Max. 3-wire sensor type input devices 132V AC/DC Max. LED Indicating Standard with 24V AC/DC LEDs Narrow standard with 24V AC/DC LEDs Standard with 120V AC/DC LEDs Narrow standard with 120V AC LEDs 24V AC/DC LEDs and extra terminals for outputs 24V AC/DC LEDs and extra terminals for inputs 120V AC LEDs and extra terminals for outputs 120V AC LEDs and extra terminals for inputs 3-wire sensor with 24V AC/DC LEDs 8 Individually isolated with 24/48V AC/DC LEDs and 4 terminals/output 8 Individually isolated with 120V AC LEDs and 4 terminals/output 240V AC LEDs and extra terminals for outputs 240V AC LEDs and extra terminals for inputs Fusible 120V AC/DC with Extra terminals for outputs Extra terminals with 24V AC/DC blown fuse LED indicators Extra terminals with 120V AC/DC blown fuse LED indicators Extra terminals with 240V AC/DC blown fuse LED indicators Extra terminals with 24V AC/DC blown fuse LED indicators for inputs Extra terminals with 120V AC/DC blown fuse LED indicators for inputs 8 Individually isolated 120V AC/DC with extra terminals for outputs 8 Individually isolated with extra terminals output, and 24V AC/DC blown fuse indicators 1492-IFM20F-F-2 1492-IFM20F-F24-2 1492-RIFM20F-F-2 1492-RIFM20F-F24-2 C E E E E E E E E E E D D 1492-IFM20D24 1492-IFM20D24N 1492-IFM20D120 1492-IFM20D120N 1492-IFM20D24-2 1492-IFM20D24A-2 1492-IFM20D120-2 1492-IFM20D120A-2 1492-IFM20D24-3 1492-IFM20DS24-4 B B B B B B B B B B B C E E E E E E E E D 1492-IFM20F-2 1492-IFM20F-3
A G N B B B B B E E E E E D
C D S
A B B B B B
1492-IFM20DS120-4
1492-IFM20D240-2 1492-IFM20D240A-2
1492-IFM20F-F120-2
1492-RIFM20F-F120-2
1492-IFM20F-F240-2
1492-IFM20F-F24A-2
1492-RIFM20F-F24A-2
1492-IFM20F-F120A-2
1492-RIFM20F-F120A-2
1492-IFM20F-FS-2
1492-IFM20F-FS24-2
Note: Footnotes are on the following page. Publication 1492-TD008C-EN-P - September 2005
scIC8I
OBP16
OVP16
OB16E
OW16
ITV16
OA16
OB16
OG16
OV16
IV16
OX8
32
Bulletin 1746 Digital 16-Point and 8-Point Isolated I/O Modules (Continued)
scOAP81 A A A sc-IA8I sc-IB8I Description of 20-PIN IFM Catalog Number for Wiring System Module with Fixed Terminal Block Catalog Number for I/O Module Catalog Number 1746- Wiring System Module with Removable Terminal Block Socket Assembly (order plugs separately) ITB16 IM16 IN16 IA16 IB16 IG16 IH16 IC16
Two 4-point isolated groups 1492-IFM20F-FS24A-4 with four terminals/input and 24V AC/DC blown fuse LED indicators 8 Individually isolated with 1492-IFM20F-FS120-2 extra terminals output, and 120V AC/DC blown fuse LED indicators 8 Individually isolated with 1492-IFM20F-FS120-4 four terminals/output and 120V AC/DC blown fuse LED indicators Two 4-point isolated groups 1492-IFM20F-FS120A-4 with four terminals/input and 120V AC/DC blown fuse indicators 8 Individually isolated with 1492-IFM20F-FS240-4 four terminals/output and 240V AC/DC blown fuse LED indicators Relay Master (LED Indicating) 20-pin master with eight (8) 24V DC relays 20-pin master with eight (8) 120V AC relays 20-pin master with sixteen (16) 24V DC relays 20-pin master with sixteen (16) 24V DC relays with fusing 20-pin master with sixteen (16) 120V AC relays 20-pin master with sixteen (16) 120V AC relays with fusing Expander with eight (8) 24V DC relays Expander with eight (8)120V AC relays Fusible Expander 8-ch. expander with 24V DC blown fuse indicators 1492-XIMF-F24-2 1492-XIM2024-8R 1492-XIM20120-8R 1492-XIM2024-16R 1492-XIM2024-16RF
CR E E E E E E
1492-XIM20120-16R 1492-XIM20120-16RF
CR CR
8-ch. expander with 120V AC 1492-XIMF-F120-2 blown fuse indicators Feed-through Expander Expander with eight feedthrough channels 1492-XIMF-2
Can have up to 1 expandable module depending upon master used (total 16 pts or less), extender cable is provided. Cables are available in standard lengths of 0.5 m 1.0 m, 2.5 m, and 5.0 m. To order, insert the code for the desired cable length into the catalog number 005 = 0.5 m (010 = 1.0 m, 025 = 2.5 m, and 050 = 5.0 m), and insert the letter in the box. Example: Catalog Number 1492-CABLE050A is for a 5.0 m cable, and the letter A. For information concerning this I/O module, contact Spectrum Controls (Phone: 425-641-9473) or at www.spectrumcontrols.com. This IFM is not recommended for use with PLC I/O modules that have an off-state leakage current exceeding 0.5 mA. Use a 1492-IFM20D120N or 1492-IFM20D120A-2 for inputs. Use 1492-IFM20D120-2 for outputs. The voltage rating is relay control/coil voltage. For relay contact ratings, refer to page 186. The LED indicates the PLC output status. Compatible Removable Terminal Block (RTB) plug; 1492-RTB20N (screw style terminals) or 1492-RTB20P (push-in style terminals, available March 2006). ORDER PLUGS SEPARATELY. Compatible Removable Terminal Block (RTB) plug; 1492-RTB10N (screw style terminals) or 1492-RTB10P (push-in style terminals, available March 2006. ORDER PLUGS SEPARATELY.
scIC8I
OBP16
OVP16
OB16E
OW16
ITV16
OA16
OB16
OG16
OV16
IV16
OX8
33
Feed-through Standard 132V AC/DC Max. Extra terminals132V AC/DC Max. 3-wire sensor type input devices 60V AC/DC Max. LED Indicating Standard with 24V AC/DC LEDs 24V AC/DC LEDs and extra terminals for outputs 24V AC/DC LEDs and extra terminals for inputs 120V AC LEDs and extra terminals for outputs 120V AC LEDs and extra terminals for inputs 3-wire sensor with 24V AC/DC LEDs 16 Individually isolated with 24/48V AC/DC LEDs and four terminals/output 16 Individually isolated with 24V AC/DC LEDs and four terminals/input 16 Individually isolated with 120V AC LEDs and four terminals/output 16 Individually isolated with 120V AC LEDs and four terminals/input 16 Individually isolated with 240V AC LEDs and four terminals/input Fusible 120V AC/DC with extra terminals for outputs Extra terminals with 24V AC/DC blown fuse LED indicators for outputs Extra terminals with 120V AC/DC blown fuse LED indicators for outputs 16 Individually isolated with extra terminals for 120V AC/DC outputs 16 Individually isolated with extra terminals and 24V AC/DC blown fuse indicators 16 Individually isolated with 24V AC/DC blown fuse indicators and four terminals/output 16 Individually isolated 240V AC/DC with 4 terminals/output 16 Individually isolated with extra terminals and 120V AC/DC blown fuse LED indicators 16 Individually isolated with 120V AC/DC blown fuse LED indicators and four terminals/output 16 Individually isolated with 240V AC/DC blown fuse LED indicators and four terminals/output 16 Individually isolated with 24V AC/DC blown fuse LED indicators and four terminals/input 16 Individually isolated 120V AC/DC with 4 terminals/input 16 Individually isolated with 120V AC/DC blown fuse LED indicators and four terminals/input 16 Individually isolated with 240V AC/DC blown fuse LED indicators and 4 terminals/input Relay Master 40-pin master with eight (8) 24V DC relays 40-pin master with sixteen (16) 24V DC relays 40-pin master with sixteen (16) 24V DC relays with fusing Note: Footnotes are on the following page.
1492-IFM40F 1492-IFM40F-2 1492-IFM40F-3 1492-IFM40D24 1492-IFM40D24-2 1492-IFM40D24A-2 1492-IFM40D120-2 1492-IFM40D120A-2 1492-IFM40D24-3 1492-IFM40DS24-4 1492-IFM40DS24A-4 1492-IFM40DS120-4 1492-IFM40DS120A-4 1492-IFM40DS240A-4 1492-IFM40F-F-2 1492-IFM40F-F24-2 1492-IFM40F-F120-2 1492-IFM40F-FS-2 1492-IFM40F-FS24-2 1492-IFM40F-FS24-4 1492-IFM40F-FS-4 1492-IFM40F-FS120-2 1492-IFM40F-FS120-4 1492-IFM40F-FS240-4 1492-IFM40F-FS24A-4 1492-IFM40F-FSA-4 1492-IFM40F-FS120A4 1492-IFM40F-FS240A4 1492-XIM4024-8R 1492-XIM4024-16R 1492-XIM4024-16RF
H H H H H H H H H
34
Relay Expander (LED Indicating) Expander with eight (8) 24V DC relays Expander with sixteen (16) 24V DC relays with fusing Expander with eight (8) 120V AC relays Fusible Expander (LED Indicating) 8-channel expander with 24V DC blown fuse indicators 8-channel expander with 120V AC blown fuse indicators Feed through Expander Expander with eight feed-through channels
Can have up to 2 or 3 expandable modules depending upon master used (total 32 pts or less), extender cable is provided. Cables are available in standard lengths of 0.5 m 1.0 m, 2.5 m, and 5.0 m. To order, insert the code for the desired cable length into the catalog number 005 = 0.5 m (010 = 1.0 m, 025 = 2.5 m, and 050 = 5.0 m), and insert the letter in the box. Example: Catalog Number 1492-CABLE050Yis for a 5.0 m cable, and the letter Y. 1492-XIM24-16RF is to be used with 1492-XIM4024-16R and 1492-XIM4024-16RF 32 PT. Only. The voltage rating is relay control/coil voltage. For relay contact ratings, refer to page 186. The LED indicates the PLC output status. Compatible Removable Terminal Block (RTB) plug; 1492-RTB20N (screw style terminals) or 1492-RTB20P (push-in style terminals, available March 2006). ORDER PLUGS SEPARATELY. Compatible Removable Terminal Block (RTB) plug; 1492-RTB17N (screw style terminals) or 1492-RTB17P (push-in style terminals, available March 2006). ORDER PLUGS SEPARATELY. Compatible Removable Terminal Block (RTB) plug; 1492-RTB14N (screw style terminals) or 1492-RTB14P (push-in style terminals, available March 2006). ORDER PLUGS SEPARATELY. Compatible Removable Terminal Block (RTB) plug; 1492-RTB12N (screw style terminals) or 1492-RTB12P (push-in style terminals, available March 2006). ORDER PLUGS SEPARATELY.
35
Cables are available in standard lengths of 0.5 m, 1.0 m, 2.5 m, and 5.0 m. To order, insert the code for the desired cable length into the catalog number (005 = 0.5 m, 010 = 1.0 m, 025 = 2.5 m, and 050 = 5.0 m). Example: Catalog Number 1492-CABLE005N is for a 0.5 m cable that could be used to connect a Catalog Number 1492-IFM20D24N IFM to a Catalog Number 1746-OW16 I/O module. Build-to-order lengths are also available.
The I/O module-ready cables have a pre-wired RTB on one end to plug onto the front of a Bulletin 1746 I/O module and 20 or 40 individually colored #18 AWG conductors on the other end. These cables provide the convenience of pre-wired connections at the I/O module end, while still allowing the flexibility to field-wire to standard terminal blocks of your choice.
I/O Module-Ready Cables for Bulletin 1746 Digital I/O Modules
Cable Catalog Number 1492-CABLEN3 1492-CABLERTBB 1492-CABLERTBO 1492-CABLERTBR Standard Cable Lengths 1.0, 2.5, 5.0 m 1.0, 2.5, 5.0 m 1.0, 2.5, 5.0 m 1.0, 2.5, 5.0 m Build-to-Order Available Yes Yes Yes Yes No. of Conductors 40 20 20 20 Mating 1746 I/O Module Catalog Number 1746-IB32, -IV32, -OB32, -OV32, -OB32E 1746-IB16, -IC16, -IG16, -IH16, -IN16, -ITB16, -ITV16, -IV16, -OB16, -OB16E, -OBP8, -OBP16, -OG16, -OV16, -OVP16 1746-OW16, -OX8 1746-IA16, -OA16, -OAP12, -IM16
Cables are available in standard lengths of 1.0 m, 2.5 m, and 5.0 m. To order, insert the code for the desired cable length into the catalog number (010 = 1.0 m, 025 = 2.5 m, and 050 = 5.0 m). Example: Catalog Number 1492-CABLE050RTBR is for a 5.0 m cable with a pre-wired Catalog Number 1746-RT25R RTB on one end. Digital I/O module-ready cables should not be used with analog module as a cable shield and drain wire is not provided.
Note: The following I/O Modules do not have RTBs: 1746-IA4, 1746-IA8, 1746-IB8, 1746-IM4, 1746-IM8, 1746-IV8, 1746-OA8, 1746-OB8.
36
Catalog Number for Wiring System Module with Fixed Terminal Block
NIO4V
Feed-through 4-channel input, output or 2-in/2-out combination with 3 terminals/channel 6-channel isolated with 34 terminals/channel 8- or 16-channel input or output with 3 terminals/channel Thermocouple 6-channel with 3 terminals/channel Fusible 2-channel input, 2-channel output with 24V DC 1492-AIFM4C-F-5 blown fuse indicators, test points, 5 terminals/input, 3 terminals/output 4-channel input with 24V DC blown fuse indicators, test points, 5 terminals/input 8-channel input with 24V DC blown fuse indicators, 5 terminals/channel 16-channel input with 24V DC blown fuse indicators, 3 terminals/channel 16-channel input with 24V DC blown fuse indicators, 5 terminals/channel 1492-AIFM4I-F-5 1492-AIFM8-F-5 1492-AIFM16-F-3 1492-AIFM16-F-5 L L L L 1492-AIFM6TC-3 1492-AIFM4-3 1492-AIFM6S-3 1492-AIFM8-3 1492-RAIFM4-3 1492-RAIFM6S-3 1492-RAIFM8-3 L L A C L L B R B R D
A46 A46
A46 A46
4-input/4-output channel with 8 fuses and 24V 1492-AIFMQS DC blown fuse indicators
Cables are available in standard lengths of 0.5 m 1.0 m, 2.5 m, and 5.0 m. To order, insert the code for the desired cable length into the catalog number 005 = 0.5 m (010 = 1.0 m, 025 = 2.5 m, and 050 = 5.0 m), and insert the letter in the box. Example: Catalog Number 1492-ACABLE025A is for a 2.5 m cable, and the letter A. Cannot be used with SLC I/O. Compatible Removable Terminal Block (RTB) plug; 1492-RTB8N (screw style terminals) or 1492-RTB8P (push-in style terminals, available March 2006). ORDER PLUGS SEPARATELY. Compatible Removable Terminal Block (RTB) plug; 1492-RTB12N (screw style terminals) or 1492-RTB12P (push-in style terminals, available March 2006). ORDER PLUGS SEPARATELY. Compatible Removable Terminal Block (RTB) plug; 1492-RTB16N (screw style terminals) or 1492-RTB16P (push-in style terminals, available March 2006). ORDER PLUGS SEPARATELY.
These pre-wired cables have a pre-wired RTB on one end to connect to the front of a Bulletin 1746 analog I/O module and a connector on the other end to plug into a 15- or 25-pin D-shell terminal AIFM. To use this table, you must first have selected an AIFM from the preceding table.
Pre-Wired Cables for Bulletin 1746 Analog I/O Modules
Cable Catalog Standard Cable Lengths (m) Build-to-Order Available AIFM Connector Mating 1746 I/O Module Catalog Number Number 1492-ACABLEA 0.5, 1.0, 2.5, 5.0 Yes 15-pin D-shell 1746-NI4 1492-ACABLEB 0.5, 1.0, 2.5, 5.0 Yes 15-pin D-shell 1746-NO4I, -NO4V 1492-ACABLEC 0.5, 1.0, 2.5, 5.0 Yes 25-pin D-shell 1746-NI8 1492-ACABLED 0.5, 1.0, 2.5, 5.0 Yes 25-pin D-shell 1746-NR4 1492-ACABLEL 0.5, 1.0, 2.5, 5.0 Yes 15-pin D-shell 1746-NIO4I, -NIO4V, -FIO4I, -FIO4V 1492-ACABLEQ 0.5, 1.0, 2.5, 5.0 Yes 25-pin D-shell 1746-QS 1492-ACABLER 0.5, 1.0, 2.5, 5.0 Yes 25-pin D-shell 1746-N08I, N08V 1492-ACABA46 0.5, 1.0, 2.5, 5.0 Yes 25-pin D-shell 1746-NI16I, -NI16V To order, insert the code for the desired cable length into the catalog number (005 = 0.5 m, 010 = 1.0 m, 025 = 2.5 m, and 050 = 5.0 m). Example: Catalog Number 1492-ACABLE005A is for a 0.5 m cable that could be used to connect a Catalog Number 1492-AIFM4I-F-5 IFM to a Catalog Number 1746-NI4 I/O module.
NI16V
FIO4V
NO4V
NO8V
NIO4I
NI16I
FIO4I
NO4I
NO8I
NR4
NI4
NI8
QS
Catalog Number for Wiring System Module with Removable Terminal Block Socket Assembly (order plugs separately
37
Using Bulletin 1756 Selection Tables to Make Valid 1492 Wiring System Module Catalog Numbers
Follow these steps when using the selection tables to make valid catalog numbers.: 1. Find the appropriate table based on the catalog number of the 1756 I/O module. 2. Find the column in the selected table for the 1756 I/O module. 3. Follow the column down to determine which Wiring System Modules are compatible with the I/O module as indicated by letter code. If there is no letter code, the 1492 Wiring System Module is not compatible with the I/O module. NOTE: The letter codes designate the compatible 1492 cable for that 1756 I/O and 1492 Wiring System Module combination. 4. Select the desired 1492 Wiring System Module. 5. Configure the cable catalog number using 1492-CABLE (for digital cables) or 1492-ACABLE (for analog cables). See footnote on pages 42 and 44.
38
Feed-through Standard 264V AC/DC Max. Narrow standard 132V AC/DC Max. Extra terminals (2 per I/O) 264V AC/DC Max. 3-wire sensor type input devices 132V AC/DC Max. LED Indicating Standard with 24V AC/DC LEDs Narrow standard with 24V AC/DC LEDs Standard with 120V AC/DC LEDs Narrow standard with 120V AC LEDs 24V AC/DC LEDs and extra terminals for outputs 24V AC/DC LEDs and extra terminals for inputs 120V AC LEDs and extra terminals for outputs 120V AC LEDs and extra terminals for inputs 3-wire sensor with 24V AC/DC LEDs 8 Individually isolated with 24/48V AC/DC LEDs and 4 terminals/output 8 Individually isolated with 120V AC LEDs and 4 terminals/output 240V AC LEDs with extra terminals for outputs 240V AC LEDs with extra terminals for inputs Fusible 120V AC/DC with extra terminals for outputs Extra terminals with 24V AC/DC blown fuse LED indicators Extra terminals with 120V AC/DC blown fuse LED indicators Extra terminals with 240V AC/DC blown fuse LED indicators Extra terminals with 24V AC/DC blown fuse LED indicators Extra terminals with 120V AC/DC blown fuse LED indicators 8 Individually isolated 120V AC/DC with extra terminals for outputs 8 Individually isolated with extra terminals/output and 24V AC/DC blown fuse LED indicators Two 4-point isolated groups with four terminals/input and 24V AC/DC blown fuse LED indicators 8 Individually isolated with extra terminals output, and 120V AC/DC blown fuse LED indicators 8 Individually isolated with 4 terminals/output and 120V AC/DC blown fuse LED indicators Two 4-point isolated groups with four terminals/input and 120V AC/DC blown fuse indicators 8 Individually isolated with 4 terminals/output and 240V AC/DC blown fuse LED indicators 1492-IFM20F-F-2 1492-IFM20F-F24-2 1492-IFM20F-F120-2 1492-IFM20F-F240-2 1492-IFM20F-F24A-2 1492-IFM20F-F120A-2 1492-IFM20F-FS-2 1492-IFM20F-FS24-2 1492-RIFM20F-F-2 1492-RIFM20F-F24-2 1492-RIFM20F-F120-2 1492-RIFM20F-F24A-2 1492-RIFM20F-F120A-2 X X X X W V V X X X W W X X 1492-IFM20D24 1492-IFM20D24N 1492-IFM20D120 1492-IFM20D120N 1492-IFM20D24-2 1492-IFM20D24A-2 1492-IFM20D120-2 1492-IFM20D120A-2 1492-IFM20D24-3 1492-IFM20DS24-4 1492-IFM20DS120-4 1492-IFM20D240-2 1492-IFM20D240A-2 U U U X X X X X X X X X X X X X X X W V V X X W X X X 1492-IFM20F 1492-IFM20FN 1492-IFM20F-2 1492-IFM20F-3 U U U X X X X X X X X X X X X X X X X X X X X U U U U U U U U U X X X U U U X X X
1492-IFM20F-FS24A-4
1492-IFM20F-FS120-2
1492-IFM20F-FS120-4
1492-IFM20F-FS120A-4
1492-IFM20F-FS240-4
Note: Footnotes are on the following page. Publication 1492-TD008C-EN-P - September 2005
39
Relay Master (LED Indicating) 20-pin master with eight (8) 24V DC relays 20-pin master with eight (8) 120V AC relays 20-pin master with sixteen (16) 24V CD relays 20-pin master with sixteen (16) 24V DC relays with fusing 20-pin master with sixteen (16) 120V AC relays 20-pin master with sixteen (16) 120V AC relays with fusing Relay Expander (LED Indicating) Expander with eight (8) 24V DC relays Expander with eight (8) 120V AC Relays Fusible Expander Expander with eight (8) 24V channels with blown fuse indicators Expander with eight (8) 120V channels with blown fuse indicators Feed-through Expander Expander with eight (8) feed-through channels 1492-XIMF-2 1492-XIMF-F24-2 1492-XIMF-F120-2 1492-XIM24-8R 1492-XIM120-8R
Can have up to 1 expandable module depending upon master used (total 16 pts or less) extender cable is provided. Cables are available in standard lengths of 0.5 m 1.0 m, 2.5 m, and 5.0 m. To order, insert the code for the desired cable length into the catalog number 005 = 0.5 m (010 = 1.0 m, 025 = 2.5 m, and 050 = 5.0 m), and insert the letter in the box. Example: Catalog Number 1492-CABLE050W is for a 5.0 m cable, and the letter W. This IFM is not recommended for use with PLC I/O modules that have an off-state leakage current exceeding 0.5 mA. Use a 1492-IFM20D120N or 1492-IFM20D120A-2 for inputs. Use 1492-IFM20D120-2 for outputs. The voltage rating is relay control/coil voltage. For relay contact ratings, refer to page 186. The LED indicates the PLC output status. Compatible Removable Terminal Block (RTB) plug 1492-RTB20N (screw style terminals) or 1492-RTB20P (push-in style terminals, available March 2006). ORDER PLUGS SEPARATELY. Compatible Removable Terminal Block (RTB) plug; 1492-RTB10N (screw style terminals) or 1492-RTB10P (push-in style terminals, available March 2006. ORDER PLUGS SEPARATELY.
40
IM16I
OB32
IA16I
IB16I
IH16I
OH8I
Feed-through Standard 132V AC/DC Max. Extra terminals (2 per I/O) 132V AC/DC Max. 3-wire sensor type input devices 60V AC/DC Max. LED Indicating Standard with 24V AC/DC LEDs 24V AC/DC LEDs and extra terminals for outputs 24V AC/DC LEDs and extra terminals for inputs 120V AC LEDs and extra terminals for outputs 120V AC LEDs and extra terminals for inputs 3-wire sensor with 24V AC/DC LEDs 16 Individually isolated with 24/48V AC/DC LEDs and 4 terminals/output 16 Individually isolated with 24V AC/DC LEDs and 4 terminals/input 16 Individually isolated with 120V AC LEDs and 4 terminals/output 16 Individually isolated with 120V AC LEDs and 4 terminals/input 16 Individually isolated with 240V AC LEDs and 4 terminals/input Fusible 120V AC/DC with extra terminals for outputs Extra terminals with 24V AC/DC blown fuse indicators for outputs 16 Individually fused with 24V DC blown fuse low leakage (0.05 mA) LED circuit, 4 isolated groups, 2 terminals/output Individually Fused w/24V DC blown fuse low leakage (0.05 mA) LED circuit, 4 isolated groups, 4 terminals/input Extra terminals with 120V AC/DC blown fuse indicators for outputs 16 Individually isolated with extra terminals for 120V AC/DC outputs 16 Individually isolated with extra terminals and 24V AC/DC blown fuse indicators for outputs 16 Individually isolated with 24V AC/DC blown fuse indicators and 4 terminals/output 16 Individually isolated 240V AC/DC with 4 terminals/output 16 Individually isolated with extra terminals and 120V AC/DC blown fuse LED indicators 16 Individually isolated with 120V AC/DC blown fuse indicators and 4 terminals/output
1492-IFM40F 1492-IFM40F-2 1492-IFM40F-3 1492-IFM40D24 1492-IFM40D24-2 1492-IFM40D24A-2 1492-IFM40D120-2 1492-IFM40D120A-2 1492-IFM40D24-3 1492-IFM40DS24-4 1492-IFM40DS24A-4 1492-IFM40DS120-4 1492-IFM40DS120A-4 1492-IFM40DS240A-4 1492-IFM40F-F-2 1492-IFM40F-F24-2 1492-IFM40F-F24D-2
Y Y Y Z Y Z
Z Z
Z Y Y Y Y Y Y Z Z Y Z
Z Y Y Y Z
Z Z Z
Z Z Z Z Z
Z Z Z Y Y Y Y Y Y Y Y Y
Y Y
Y Y Z Z Z Z
1492-IFM40F-F24AD-4
1492-RIFM40F-FS120-2 1492-RIFM40F-FS120-4
Y Y Y Y Y Y Y Y Y Y Y Y
Y Y Y Y Y Y Y Y
Y Y Y Y Y Y
Y Y
Y Y
Note: Footnotes are on the following page. Publication 1492-TD008C-EN-P - September 2005
OX8I
IA32
IB32
IV32
41
Bulletin 1756 Digital 16-Point Isolated and 32-Point I/O Modules (Continued)
Description of 40-PIN IFM Catalog Number for Wiring System Module with Fixed Terminal Block Catalog Number for Wiring System Module with Removable Terminal Block Socket Assembly (order plugs separately I/O Module Catalog Number 1756- OB16IS OB16D OW16I OV32E OB8EI IB16D OA16I OB16I
IM16I
OB32
IA16I
IB16I
IH16I
OH8I
16 Individually isolated with 240V 1492-IFM40F-FS240-4 AC/DC blown fuse indicators and 4 terminals/output 1492-IFM40F-FS24A-4 16 Individually isolated with 24V AC/DC blown fuse indicators and 4 terminals/input 16 Individually isolated 120V AC/DC 1492-IFM40F-FSA-4 with 4 terminals/input 1492-IFM40F-FS120A-4 16 Individually Isolated with 120V AC/DC blown fuse indicators and 4 terminals/input 1492-IFM40F-FS240A-4 16 Individually isolated with 240V AC/DC blown fuse indicators and 4 terminals/input Relay Master (LED Indicating) 40-pin master with eight (8) 24V DC 1492-XIM4024-8R relays 40-pin master with sixteen (16) 24V 1492-XIM4024-16R DC relays 40-pin master with sixteen (16) 24V 1492-XIM4024-16RF DC relays with fusing Relay Expander (LED Indicating) 1492-XIM24-8R Expander with eight (8) 24V DC relays 1492-XIM120-8R Expander with eight (8) 120V AC relays Fusible Expander 1492-XIMF-F24-2 8-channel expander with 24V DC blown fuse indicators 1492-XIMF-F120-2 8-channel expander with 120V AC blown fuse indicators Expander with sixteen (16) 24V DC 1492-XIM24-16RF relays with fusing Feed-through Expander 1492-XIMF-2 Expander with eight (8) feedthrough channels
Y Y Y Y Y Y
Y Y Y
1492-RIFM40F-FS120A-4
Y Y Y
Z 1492-RXIM4024-16R Z Z 1492-RXIM24-8R
Can have up to 2 or 3 expandable modules depending upon master used (total 32 pts or less), extender cable is provided. Cables are available in standard lengths of 0.5 m 1.0 m, 2.5 m, and 5.0 m. To order, insert the code for the desired cable length into the catalog number 005 = 0.5 m (010 = 1.0 m, 025 = 2.5 m, and 050 = 5.0 m), and insert the letter in the box. Example: Catalog Number 1492-CABLE050Y is for a 5.0 m cable, and the letter Y. One 1492-XIM24-16RF is to be used with one 1492-XIM4024-16R or 1492-XIM4024-16RF master (32 PT. Only). The voltage rating is relay control/coil voltage. For relay contact ratings, refer to page 186. The LED indicates the PLC output status. The 1492-IFM40F-FS24A-4 module and 1492-CABLEY cable can be used with the 1756-IB16D module. However, due to the 1492-IFM40F-FS24A-4 modules blown fuse leakage current rating, the wire off diagnostic function of the 1756-IB16D will not indicate a blown or removed fuse as a wire off condition. If you require this diagnostic to function for a blown or removed fuse, you must use a 1492-IFM40F-F24AD-4. The 1492-IFM40F-FS24-2 and 1492-IFM40F-FS24-4 module and 1492-CABLEY cable can be used with the 1756-OB16D module. However, due to the 1492-IFM40F-FS242 and 1492-IFM40F-FS24-4 modules blown fuse leakage current rating, the no load diagnostic function of the 1756-OB16D will not indicate a blown or removed fuse as a no load condition. If you require this diagnostic to function for a blown or removed fuse, you must use a 1492-IFM40F-F24D-2. Compatible Removable Terminal Block (RTB) plug; 1492-RTB20N (screw style terminals) or 1492-RTB20P (push-in style terminals, available March 2006). ORDER PLUGS SEPARATELY. Compatible Removable Terminal Block (RTB) plug; 1492-RTB17N (screw style terminals) or 1492-RTB17P (push-in style terminals, available March 2006). ORDER PLUGS SEPARATELY. Compatible Removable Terminal Block (RTB) plug; 1492-RTB14N (screw style terminals) or 1492-RTB14P (push-in style terminals, available March 2006). ORDER PLUGS SEPARATELY. Compatible Removable Terminal Block (RTB) plug; 1492-RTB12N (screw style terminals) or 1492-RTB12P (push-in style terminals, available March 2006). ORDER PLUGS SEPARATELY.
OX8I Y
IA32
IB32
IV32
42
Pre-Wired Cables for Bulletin 1756 Digital I/O Modules Cable Catalog Number 1492-CABLEU 1492-CABLEV 1492-CABLEW 1492-CABLEX 1492-CABLEY 1492-CABLEZ Standard Cable Lengths 0.5, 1.0, 2.5, 5.0 m 0.5, 1.0, 2.5, 5.0 m 0.5, 1.0, 2.5, 5.0 m 0.5, 1.0, 2.5, 5.0 m 0.5, 1.0, 2.5, 5.0 m 0.5, 1.0, 2.5, 5.0 m Build-to-Order Available Yes Yes Yes Yes Yes Yes No. of Mating 1756 Conductors I/O Module Catalog Number 20 20 20 20 40 40 1756-IA8D, -OA8, -OA8D, -OA8E, -OB8, -OC8, -ON8 1756-OA8D, -OA8E 1756-OA8, -OB8, -OC8, -ON8 1756-IA16, -IB16, -IC16, -IN16, -IV16, -OA16, -OB16E, -OV16E 1756-IA16I, -IB16D, -IB16I, -IH16, -IM16I, -OA16I, -OB8EI, -OB16D, -OB16I, -OB16IS, -OH8I, -OW16I, -OX8I 1756-IB32, -OB32, -IV32, -OV32E
Cables are available in standard lengths of 0.5 m, 1.0 m, 2.5 m, and 5.0 m. To order, insert the code for the desired cable length into the catalog number (005 = 0.5 m, 010 = 1.0 m, 025 = 2.5 m, and 050 = 5.0 m). Example: Catalog Number 1492-CABLE005Y is for a 0.5 m cable that could be used to connect a Catalog Number 1492-IFM40F IFM to a Catalog Number 1756-IA16I I/O module.
The I/O module-ready cables have a pre-wired RTB on one end to plug onto the front of a Bulletin 1756 I/O module and 20 or 40 individually colored #18 AWG conductors on the other end. These cables provide the convenience of pre-wired connections at the I/O module end, while still allowing the flexibility to field-wire to standard terminal blocks of your choice.
I/O Module-Ready Cables for Bulletin 1756 Digital I/O Modules Cable Catalog Number 1492-CABLETBNH 1492-CABLETBCH Standard Cable Lengths 1.0, 2.5, 5.0 m 1.0, 2.5, 5.0 m Build-to-Order Available Yes Yes No. of Mating 1756 Conductors I/O Module Catalog Number 20 40 1756-IA8D, -IA16, -IB16, -IC16, -IN16, -IV16, -OA8, -OA8D, -OA8E, -OA16, -OB8, -OB16E, -OC8, -ON8, -OV16E 1756-IA16I, -IA32, -IB16D, -IB16I, -IB32, -IV32, -IH16I, -IM16I, -OA16I, -OB8EI, -OB16D, -OB16I, -OB16IS, -OB32, -OV32E, -OH8I, -OW16I, -OX8I
Cables are available in standard lengths of 1.0 m, 2.5 m, and 5.0 m. To order, insert the code for the desired cable length into the catalog number (010 = 1.0 m, 025 = 2.5 m, and 050 = 5.0 m). Example: Catalog Number 1492-CABLE050TBNH is for a 5.0 m cable with a pre-wired Catalog Number 1756-TBNH RTB on one end. Discrete I/O ready cables should not be used with PLC analog I/O modules as cable shield and drain wires are not provided.
43
Catalog Number for Wiring System Module with Removable Terminal Block Socket Assembly (order plugs separately IF8 (Sgl-End Volt) IF6I (Voltage) IF6I (Current)
OF4 (Voltage)
OF8 (Voltage)
OF4 (Current)
OF8 (Current) WB
OF6CI
OF6VI
IT6I2
Feed-through 4-channel input, output or 2-in/2-out combination with 3 terminals/channel 6-channel isolated with 34 terminals/channel 8- or 16-channel input or output with 3 terminals/channel Thermocouple 6-channel with 3 terminals/channel Fusible 8-channel input with 24V DC blown fuse indicators, 5 terminals/channel 16-channel input with 24V DC blown fuse indicators, 3 terminals/channel 16-channel input with 24V DC blown fuse indicators, 5 terminals/channel 8 input/ 2 output channels 1492-AIFM8-F-5 TA TB TC TD UC UD 1492-AIFM6TC-3 Y YT 1492-AIFM4-3 1492-RAIFM4-3 VA VB
1492-AIFM6S-3 1492-AIFM8-3
1492-RAIFM6S-3 1492-RAIFM8-3
TA TB
TC
TD
UA
UB
UC
UD
Y WA
1492-AIFM16-F-3
UA
UB
UC
UD
1492-AIFM16-F-5
UA
UB
UC
UD
1492-AIFMPI
Some analog I/O modules can be operated in up to four modes (current/voltage, single-ended/differential) based on connections. In all cases, each channel is factoryconfigured for the same mode. However, you can field configure any channel for another mode. You made need to alter the terminal block wiring to match the application. Refer to the PLC installation manual Cables are available in standard lengths of 0.5 m 1.0 m, 2.5 m, and 5.0 m. To order, insert the code for the desired cable length into the catalog number 005 = 0.5 m (010 = 1.0 m, 025 = 2.5 m, and 050 = 5.0 m), and insert the letter in the box. Example: Catalog Number 1492-ACABLE025TB is for a 2.5 m cable, and the letters TB. Compatible Removable Terminal Block (RTB) plug; 1492-RTB8N (screw style terminals) or 1492-RTB8P (push-in style terminals, available March 2006). ORDER PLUGS SEPARATELY. Compatible Removable Terminal Block (RTB) plug; 1492-RTB12N (screw style terminals) or 1492-RTB12P (push-in style terminals, available March 2006). ORDER PLUGS SEPARATELY. Compatible Removable Terminal Block (RTB) plug; 1492-RTB16N (screw style terminals) or 1492-RTB16P (push-in style terminals, available March 2006). ORDER PLUGS SEPARATELY.
PIM M
IR6I
IT6I
44
Pre-Wired Cables for 1756 Analog I/O Modules Cable Catalog Number 1492-ACABLEM 1492-ACABLEX 1492-ACABLEY 1492-ACABLEYT 1492-ACABLEZ 1492-ACABLETA 1492-ACABLETB 1492-ACABLETC 1492-ACABLETD 1492-ACABLEUA 1492-ACABLEUB 1492-ACABLEUC 1492-ACABLEUD 1492-ACABLEVA 1492-ACABLEVB 1492-ACABLEWA 1492-ACABLEWB Standard Cable Lengths 0.5, 1.0, 2.5, 5.0 m 0.5, 1.0, 2.5, 5.0 m 0.5, 1.0, 2.5, 5.0 m 0.5, 1.0, 2.5, 5.0 m 0.5, 1.0, 2.5, 5.0 m 0.5, 1.0, 2.5, 5.0 m 0.5, 1.0, 2.5, 5.0 m 0.5, 1.0, 2.5, 5.0 m 0.5, 1.0, 2.5, 5.0 m 0.5, 1.0, 2.5, 5.0 m 0.5, 1.0, 2.5, 5.0 m 0.5, 1.0, 2.5, 5.0 m 0.5, 1.0, 2.5, 5.0 m 0.5, 1.0, 2.5, 5.0 m 0.5, 1.0, 2.5, 5.0 m 0.5, 1.0, 2.5, 5.0 m 0.5, 1.0, 2.5, 5.0 m Build-to-Order Available Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes AIFM Connector 25-pin D-shell 25-pin D-shell 25-pin D-shell 25-pin D-shell 25-pin D-shell 25-pin D-shell 25-pin D-shell 25-pin D-shell 25-pin D-shell 25-pin D-shell 25-pin D-shell 25-pin D-shell 25-pin D-shell 15-pin D-shell 15-pin D-shell 25-pin D-shell 25-pin D-shell Mating 1756 I/O Module Catalog Number 1757-PIM 1756-IF16 Current 1756-IF16 Voltage, -IT6I Series A, -OF6CI, -OF6VI 1756-IT6I2 1756-IR6I 1756-IF8 Single-Ended Voltage 1756-IF8 Single-Ended Current 1756-IF8 Differential Voltage 1756-IF8 Differential Current 1756-IF16 Single-Ended Voltage 1756-IF16 Single-Ended Current 1756-IF16 Differential Voltage 1756-IF16 Differential Current 1756-OF4 Voltage 1756-OF4 Current 1756-OF8 Voltage 1756-OF8 Current
Cables are available in standard lengths of 0.5 m, 1.0 m, 2.5 m, and 5.0 m. To order, insert the code for the desired cable length into the catalog number (005 = 0.5 m, 010 = 1.0 m, 025 = 2.5 m, and 050 = 5.0 m). Example: Catalog Number 1492-ACABLE005Y is for a 0.5 m cable that could be used to connect a Catalog Number 1492-AIFM6TC-3 analog IFM to a Catalog Number 1756-IT6I I/O module.
45
Using Bulletin 1762/1764 Selection Tables to Make Valid 1492 Wiring System Module Catalog Numbers
Follow these steps when using the selection tables to make valid catalog numbers: 1. Find the appropriate table based on the catalog numbers of the 1762/1764 controller. 2. Find the column for the 1762/1764 I/O. 3. Follow the column down to determine which Wiring System Modules are compatible with the I/O as indicated by letter and number (e.g. A62) code. If there is no letter/number code, the Wiring System Module is not compatible with the I/O module. NOTE: The letter/number codes designate the compatible 1492 cable for that 1762/1764 I/O and Wiring System Module combination. 4. Select the desired Wiring System Module. 5. Configure the cable catalog number using 1492-CAB. See footnote on pages 46 and 47.
46
1492-IFM40F 1492-IFM40F-2
1492-RIFM40F 1492-RIFM40F-2
A62 A62
B62 B62
When using this IFM module with the base I/O of the 1762 controller, the current rating of the ouputs must be considered. Refer to Appendix A.
Compatible Removable Terminal Block (RTB) plug; 1492-RTB20N (screw style terminlas) or 1492-RTB20P (push-in style terminals, available March 2006). ORDER PLUGS SEPARATELY.
These pre-wired cables have a pre-wired removable terminal block (RTB) on one end to connect to the front of the Bulletin 1762 controller embedded digital I/O and a connector on the other end to plug into a 40-terminal IFM. You must first select the IFM from the preceding selection table.
Pre-Wired Cables for 1762-L40x Embedded I/O Controllers
Cable Catalog Number 1492-CABA62 1492-CABB62 Standard Cable Lengths 0.5, 1.0, 2.5, 5.0 0.5, 1.0, 2.5, 5.0 Build-to-Order Available Yes Yes No. of Conductors 40 40 Mating 1762-L40x Embedded I/O Controller -L40AWA Outputs, -L40BWA Outputs, -L40BXB Outputs -L40AWA Inputs, -L40BWA Inputs, -L40BXB Inputs
Pre-wired cables are available in standard lengths of 0.5 m, 1.0 m, 2.5 m, and 5.0 m. To order, insert the code for the desired cable length into the catalog number (005 = 0.5 m, 010 = 1.0 m, 025 = 2.5 m, and 050 = 5.0 m). Example: Catalog Number 1492-CAB005A62 is for a 0.5 m cable that could be used to connect a Catalog Number 1492-IFM40F to a Cat. No. 1762-L40AWA Input.
The I/O module-ready cables have a pre-wired RTB on one end to plug onto the front of the Bulletin 1762 controller embedded I/O and 25 or 40 individually colored conductors on the other end. These cables provide the convenience of pre-wired connections at the controller embedded I/O end, while still allowing the flexibility to field-wire to standard terminal blocks of your choice.
I/O Ready Cables for 1762-L40x Embedded I/O Controllers
Cable Catalog Number 1492-CABT62 1492-CABX62
No. of Conductors 25 40
Mating 1762-L40x Embedded I/O Controller -L40AWA Outputs, -L40BWA Outputs, -L40BXB Outputs -L40AWA Inputs, -L40BWA Inputs, -L40BXB Inputs
I/O ready cables are available in standard lengths or 1.0 m, 2.5 m, and 5.0 m. To order, insert the code for the desired cable length into the catalog number (010 = 1.0 m, 025 = 2.5 m, and 050 = 5.0 m) Example: Catalog Number 1492-CABLE050RTBR is for a 5.0 m cable with a pre-wired Catalog Number 1746-RT25R RTB on one end. 1492-CABT62 uses 18AWG wire and 1492-CABX62 uses 22AWG wire.
47
Feed-through Standard 264Vac/dc Max. Narrow standard 132Vac/dc Max. With Extra terminals (2 per I/O) 264Vac/dc Max.
1492-IFM20F 1492-IFM20FN
1492-RIFM20F 1492-RIFM20FN
1492-IFM20F-2
1492-RIFM20F02
When using this IFM module with the base I/O of the 1762 controller, the current rating of the ouputs must be considered. Refer to appendix A
Compatible Removablae Terminal Block (RTB) 1492-RTB20N (screw style terminal) or 1492-RTB20P (push-in style terminal, available March 2006). ORDER PLUGS SEPARATELY. Compatible Removable Terminal Block (RTB) plug; 1492-RTB10N (screw style terminals) or 1492-RTB10P (push-in style terminals, available March 2006. ORDER PLUGS SEPARATELY.
These pre-wired cables have a pre-wired removable terminal block (RTB) on one end to connect to the front of the Bulletin 1764 base unit digital I/O and a connector on the other end to plug into a 20-terminal IFM. You must first select the IFM from the preceding selection table.
Pre-Wired Cables for 1764 Base I/O
I/O Ready Cable Catalog Number 1492-CABA64 1492-CABB64 1492-CABC64 1492-CABF64 Standard Cable Lengths 0.5, 1.0, 2.5, 5.0 0.5, 1.0, 2.5, 5.0 0.5, 1.0, 2.5, 5.0 0.5, 1.0, 2.5, 5.0 Build-to-Order Available Yes Yes Yes Yes No. of Conductors 20 20 20 20 Mating 1764 Base Unit I/O AWA Inputs, BWA Inputs BXB Inputs AWA Outputs, BWA Outputs BXB Output
Pre-wired cables are available in standard lengths of 0.5 m, 1.0 m, 2.5 m, and 5.0 m. To order, insert the code for the desired cable length into the catalog number (005 = 0.5 m, 010 = 1.0 m, 025 = 2.5 m, and 050 = 5.0 m). Example: Catalog Number 1492-CAB005A64 is for a 0.5 m cable that could be used to connect a Catalog Number 1492-IFM20F to a Cat. No. 1764-AWA Input.
The I/O module-ready cables have a pre-wired RTB on one end to plug onto the front of the Bulletin 1764 base unit I/O and 20 individually colored conductors on the other end. These cables provide the convenience of prewired connections at the base unit I/O end, while still allowing the flexibility to field-wire to standard terminal blocks of your choice.
I/O Ready Cables for 1764 Base I/O
Cable Catalog Number 1492-CABT64 1492-CABU64 1492-CABW64 1492-CABX64 Standard Cable Lengths 1.0, 2.5, 5.0 m 1.0, 2.5, 5.0 m 1.0, 2.5, 5.0 1.0, 2.5, 5.0 Build-to-Order Available Yes Yes Yes Yes No. of Conductors 20 20 20 20 Mating 1764 Base Unit I/O AWA Outputs, BWA Outputs BXB Outputs AWA Inputs, BWA Inputs BXB Inputs
I/O ready cables are available in standard lengths or 1.0 m, 2.5 m, and 5.0 m. To order, insert the code for the desired cable length into the catalog number (010 = 1.0 m, 025 = 2.5 m, and 050 = 5.0 m) Example: Catalog Number 1492-CABLE050RTBR is for a 5.0 m cable with a pre-wired Catalog Number 1746-RT25R RTB on one end. Uses #18 AWG wire. Uses #22 AWG wire.
48
Using Bulletin 1769 Selection Tables to Make Valid 1492 Wiring System Module Catalog Numbers
Follow these steps when using the selection tables to make valid catalog numbers: 1. Find the appropriate table based on the catalog number of the 1769 I/O module. 2. Find the column in the selected table for the 1769 I/O module. 3. Follow the column down to determine which Wiring System Modules are compatible with the I/O module as indicated by letter code. If there is no letter code, the Wiring System Module is not compatible with the I/O module. NOTE: The letter codes designate the compatible 1492 cable for that 1769 I/O and Wiring System Module combination. 4. Select the desired Wiring System Module. 5. Configure the cable catalog number using 1492-CAB (for digital cables) or 1492-ACAB (for analog cables). See footnote on pages 53 and 55.
49
Bulletin 1769 Compact I/O for CompactLogix and MicroLogix 1500 IFMs and Cables
Catalog Number for Wiring System Module with Fixed Terminal Block Catalog Number for Wiring System Module with Removable Terminal Block Socket Assembly (order plugs separately 1492-RIFM20F 1492-RIFM20FN 1492-RIFM20F-2 I/O Module Catalog Number 1769- OW16 H69 H69 H69 H69 H69 H69 H69 H69 H69 H69 H69 H69 H69 IQ16F OW8I D69 D69 D69 D69 D69 D69 D69 D69
OA16
OB16
IM12
Feed-through Standard 264V AC/DC Max. Narrow standard 132V AC/DC Max. Extra terminals (2 per I/O) 264V AC/DC Max. 3-wire sensor type input devices 132V AC/DC Max. LED Indicating Standard with 24V AC/DC LEDs Narrow standard with 24V AC/DC LEDs Standard with 120V AC/DC LEDs Narrow standard with 120V AC LEDs 24V AC/DC LEDs and extra terminals for outputs 24V AC/DC LEDs and extra terminals for inputs 120V AC LEDs and extra terminals for outputs 120V AC LEDs and extra terminals for inputs 3-wire sensor with 24V AC/DC LEDs 8 Individually isolated with 24/48V AC/DC LEDs and 4 terminals/output 8 Individually isolated with 120V AC LEDs and 4 terminals/output 240V AC LEDs and extra terminals for outputs 240V AC LEDs and extra terminals for inputs Fusible 120V AC/DC with extra terminals for outputs Extra terminals with 24V AC/DC blown fuse LED indicators Extra terminals with 120V AC/DC blown fuse LED indicators Extra terminals with 240V AC/DC blown fuse LED indicators Extra terminals with 24V AC/DC blown fuse LED indicators Extra terminals with 120V AC/DC blown fuse LED indicators 8 Individually isolated 120V AC/DC with extra terminals for outputs 8 Individually isolated with extra terminals output, and 24V AC/DC blown fuse indicators Two 4-point isolated groups with four terminals/input and 24V AC/DC blown fuse LED indicators 8 Individually isolated with extra terminals output, and 120V AC/DC blown fuse LED indicators 8 Individually isolated with four terminals/output and 120V AC/DC blown fuse LED indicators Two 4-point isolated groups with four terminals/input and 120V AC/DC blown fuse indicators 8 Individually isolated with four terminals/output and 240V AC/DC blown fuse LED indicators
F69 F69
G69 G69
1492-IFM20D24 1492-IFM20D24N 1492-IFM20D120 1492-IFM20D120N 1492-IFM20D24-2 1492-IFM20D24A-2 1492-IFM20D120-2 1492-IFM20D120A-2 1492-IFM20D24-3 1492-IFM20DS24-4 1492-IFM20DS120-4 1492-IFM20D240-2 1492-IFM20D240A-2
G69
C69
C69 C69
A69
B69
B69
C69
H69 H69
E69 E69
C69 C69
1492-IFM20F-FS24A-4
1492-IFM20F-FS120-2
C69
C69
1492-IFM20F-FS120-4
C69
C69
1492-IFM20F-FS120A-4
1492-IFM20F-FS240-4
Note: Footnotes are on the following page. Publication 1492-TD008C-EN-P - September 2005
OW8
IA16
IQ16
OA8
IA8I
50
OA16
OB16
OV16
IM12
Relay Master (LED Indicating) 20-pin master with eight (8) 24V DC relays 20-pin master with eight (8) 120V AC relays 20-pin master with sixteen (16) 24V DC relays with fusing 20-pin master with sixteen (16) 24V DC relays with fusing 20-pin master with sixteen (16) 120V AC relays 20-pin master with sixteen (16) 120V AC relays with fusing Relay Expander (LED Indicating) Expander with eight (8) 24V DC relays Expander with eight (8) 120V AC relays Fusible Expander 8-channel expander with 24V DC blown fuse indicators 8-channel expander with 120V AC blown fuse indicators Feed-through Expander Expander with eight (8) feed-through channels
1492-XIMF-2
In the input modules sink mode only. One expander module is connected to a master to provide a total of 16 outputs. An extender cable is included with each expander to connect it to the master. Cables are available in standard lengths of 0.5 m 1.0 m, 2.5 m, and 5.0 m. To order, insert the code for the desired cable length into the catalog number 005 = 0.5 m (010 = 1.0 m, 025 = 2.5 m, and 050 = 5.0 m), and insert the letter in the box. Example: Catalog Number 1492-CABLE050A is for a 5.0 m cable, and the letter A. This IFM is not recommended for use with PLC I/O modules that have an off-state leakage current exceeding 0.5 mA. Use a 1492-IFM20D120N or 1492-IFM20D120A-2 for inputs. Use 1492-IFM20D120-2 for outputs. The voltage rating is relay control/coil voltage. For relay contact ratings, refer to page 186. The LED indicates the PLC output status. Compatible Removable Terminal Block (RTB) plug; 1492-RTB20N (screw style terminals) or 1492-RTB20P (push-in style terminals, available March 2006). ORDER PLUGS SEPARATELY. Compatible Removable Terminal Block (RTB) plug; 1492-RTB10N (screw style terminals) or 1492-RTB10P (push-in style terminals, available March 2006. ORDER PLUGS SEPARATELY.
OW8
IA16
IQ16
OA8
IA8I
51
Bulletin 1769 Compact I/O for CompactLogix and MicroLogix 1500 IFMs and Cables, Continued
Feed-through Standard 132V AC/DC Max. Extra terminals (2 per I/O) 132V AC/DC Max. 3-wire sensor type input devices 60V AC/DC Max. LED Indicating Standard with 24V AC/DC LEDs 24V AC/DC LEDs and extra terminals for outputs 24V AC/DC LEDs and extra terminals for inputs 120V AC LEDs and extra terminals for outputs 120V AC LEDs and extra terminals for inputs 3-wire sensor with 24V AC/DC LEDs 16 Individually isolated with 24/48V AC/DC LEDs and 4 terminals/output 16 Individually isolated with 24V AC/DC LEDs and 4 terminals/input 16 Individually isolated with 120V AC LEDs and 4 terminals/output 16 Individually isolated with 120V AC LEDs and 4 terminals/input 16 Individually isolated with 240V AC LEDs and 4 terminals/input Fusible 120V AC/DC with extra terminals for outputs Extra terminals with 24V AC/DC blown fuse indicators for outputs Extra terminals with 120V AC/DC blown fuse indicators 16 Individually isolated with extra terminals for 120V AC/DC outputs 16 Individually isolated with extra terminals and 24V AC/DC blown fuse indicators 16 Individually isolated with 24V AC/DC blown fuse indicators and 4 terminals/output 16 Individually isolated 240V AC/DC with 4 terminals/output 16 Individually isolated with extra terminals and 120V blown fuse indicators 16 Individually isolated with 120V AC/DC blown fuse indicators and 4 terminals/output 16 Individually isolated with 240V AC/DC blown fuse indicators and 4 terminals/output 16 Individually isolated with 24V AC/DC blown fuse indicators and 4 terminals/input 16 Individually isolated 120V AC/DC with 4 terminals/input 16 Individually isolated with 120V AC/DC blown fuse indicators and 4 terminals/input 16 Individually isolated with 240V AC/DC blown fuse indicator and 4 terminals/input Relay Master (LED Indicating) 40-pin master with eight (8) 24V DC relays Note: Footnotes are on the following page.
1492-IFM40F 1492-IFM40F-2 1492-IFM40F-3 1492-IFM40D24 1492-IFM40D24-2 1492-IFM40D24A-2 1492-IFM40D120-2 1492-IFM40D120A-2 1492-IFM40D24-3 1492-IFM40DS24-4 1492-IFM40DS24A-4 1492-IFM40DS120-4 1492-IFM40DS120A-4 1492-IFM40DS240A-4
1492-IFM40F-F-2 1492-IFM40F-F24-2 1492-IFM40F-F120-2 1492-IFM40F-FS-2 1492-IFM40F-FS24-2 1492-IFM40F-FS24-4 1492-IFM40F-FS-4 1492-IFM40F-FS120-2 1492-IFM40F-FS120-4 1492-IFM40F-FS240-4 1492-IFM40F-FS24A-4 1492-IFM40F-FSA-4 1492-IFM40F-FS120A-4 1492-IFM40F-FS240A-4
K69 K69
1492-XIM4024-8R
K69
52
40-pin master with sixteen (16) 24V DC relays 40-pin master with sixteen (16) 24V DC relays with fusing Relay Expander (LED Indicating) Expander with eight (8) 24V DC relays Expander with eight (8) 120V AC relays Fusible Expander 8-channel expander with 24V DC blown fuse indicators 8-channel expander with 120V AC blown fuse indicators Expander with sixteen (16) 24V DC relays with fusing Feed-through Expander Expander with eight (8) feed-through channels
1492-RXIM24-8R
Cables are available in standard lengths of 0.5 m 1.0 m, 2.5 m, and 5.0 m. To order, insert the code for the desired cable length into the catalog number 005 = 0.5 m (010 = 1.0 m, 025 = 2.5 m, and 050 = 5.0 m), and insert the letter in the box. Example: Catalog Number 1492-CABLE050A is for a 5.0 m cable, and the letter A. Can have 2 or 3 expander modules depending on master used (32 pts. or less). Extender cable is provided. One 1492-XIM24-16RF is to be used with one 1492-XIM4024-16R or 1492-XIM4024-16RF master (32 pts. max.). The voltage rating is relay control/coil voltage. For relay contact ratings, refer to page 186. The LED indicates the PLC output status. Compatible Removable Terminal Block (RTB) plug; 1492-RTB20N (screw style terminals) or 1492-RTB20P (push-in style terminals, available March 2006). ORDER PLUGS SEPARATELY. Compatible Removable Terminal Block (RTB) plug; 1492-RTB17N (screw style terminals) or 1492-RTB17P (push-in style terminals, available March 2006). ORDER PLUGS SEPARATELY. Compatible Removable Terminal Block (RTB) plug; 1492-RTB14N (screw style terminals) or 1492-RTB14P (push-in style terminals, available March 2006). ORDER PLUGS SEPARATELY. Compatible Removable Terminal Block (RTB) plug; 1492-RTB12N (screw style terminals) or 1492-RTB12P (push-in style terminals, available March 2006). ORDER PLUGS SEPARATELY.
53
Bulletin 1769 Compact I/O for CompactLogix and MicroLogix 1500 IFMs and Cables, Continued
These pre-wired cables have a pre-wired RTB on one end to connect to the front of a Bulletin 1769 digital I/O module and a connector on the other end to plug into a 20- or 40-terminal IFM/XIM. You must first select the IFM/XIM from the preceding selection table.
Pre-Wired Cables for Bulletin 1769 Digital I/O Modules Cable Catalog Number 1492-CABA69 1492-CABB69 1492-CABC69 1492-CABD69 1492-CABE69 1492-CABF69 1492-CABG69 1492-CABH69 1492-CABJ69 1492-CABK69 Standard Cable Lengths 0.5, 1.0, 2.5, 5.0 m 0.5, 1.0, 2.5, 5.0 m 0.5, 1.0, 2.5, 5.0 m 0.5, 1.0, 2.5, 5.0 m 0.5, 1.0, 2.5, 5.0 m 0.5, 1.0, 2.5, 5.0 m 0.5, 1.0, 2.5, 5.0 m 0.5, 1.0, 2.5, 5.0 m 0.5, 1.0, 2.5, 5.0 m 0.5, 1.0, 2.5, 5.0 m Build-to-Order Available Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No. of Conductors 20 20 20 20 20 20 20 20 40 40 Mating 1769 I/O Module Catalog Number 1769-IA16 1769-IQ16 1769-OA8, -OW8 1769-OW8I 1769-OB16, -OV16 1769-IA8I 1769-IM12 1769-OA16, -OW16 1769-IQ32 1769-OB32
Cables are available in standard lengths of 0.5 m, 1.0 m, 2.5 m, and 5.0 m. To order, insert the code for the desired cable length into the catalog number (005 = 0.5 m, 010 = 1.0 m, 025 = 2.5 m, and 050 = 5.0 m). Example: Catalog Number 1492-CAB005E69 is for a 0.5 m cable that can be used to connect a Catalog Number 1492-IFM20D24N IFM to a Catalog Number 1769-OB16 I/O module.
The I/O module-ready cables have a pre-wired RTB on one end to plug onto the front of a Bulletin 1769 I/O module and 20 individually colored #18 AWG conductors on the other end. These cables provide the convenience of pre-wired connections at the I/O module end, while still allowing the flexibility to field-wire to standard terminal blocks of your choice.
I/O Module-Ready Cables for Bulletin 1769 Digital I/O Modules Cable Catalog Number 1492-CABRTN10 1492-CABRTN18 Standard Cable Lengths 1.0, 2.5, 5.0 m 1.0, 2.5, 5.0 m Build-to-Order Available Yes Yes Yes Yes No. of Conductors 12 20 40 40 Mating 1769 I/O Module Catalog Number 1769-OA8, -OW8 1769-IA8I, -IA16, -IQ16, -IQ16F, -OA16, -OB16, -OV16, -OW16, -OW8I, -IM12 1769-IQ32 1769-OB32
1492-CAB RTN32I and 1492-CAB RTN320 cables use 22 AWG wire. Cables are available in standard lengths of 1.0 m, 2.5 m, and 5.0 m. To order, insert the code for the desired cable length into the catalog number (010 = 1.0 m, 025 = 2.5 m, and 050 = 5.0 m). Example: Catalog Number 1492-CAB050RTN10 is for a 5.0 m cable with a wired Catalog Number 1746-RTBN10 on one end. Discrete I/O ready cables should not be used with PLC analog I/O modules as a cable shield and drain wires are not provided.
54
Bulletin 1769 Compact I/O for CompactLogix and MicroLogix 1500 AIFMs and Cables
Catalog Number for Wiring System Module with Fixed Terminal Block
Catalog Number for Wiring System Module with Removable Terminal Block Socket Assembly (order plugs separately
OF2 (Voltage)
OF8V (Voltage)
Feed-through 4-channel input, output or 2-in/2-out combination with 3 terminals/channel 6-channel isolated with 34 terminals/channel 8- or 16-channel input or output with 3 terminals/channel Thermocouple 6-channel with 3 terminals/channel Fusible 4-channel with 24V DC blown fuse indicators, test points, 5 terminals/input 3 terminals/output 2-channel input, 2-channel output with 24V DC blown fuse indicators, test points, 5 terminals/input, 3 terminals/output 8-channel input with 24V DC blown fuse indicators, 5 terminals/channel 16-channel input with 24V DC blown fuse indicators, 3 terminals/channel 16-channel input with 24V DC blown fuse indicators, 5 terminals/channel 4-input/4-output channel with 8 fuses and 24V DC blown fuse indicators 1492-AIFM4I-F-5 BA69 BB69 BC69 BD69 1492-AIFM6TC-3 1492-AIFM4-3 1492-RAIFM4-3 BA69 BB69 BC69 BD69 AA69
1492-AIFM6S-3 1492-AIFM8-3
1492-RAIFM6S-3 1492-RAIFM8-3
EA69
EB69
EC69
ED69
C69
D69
1492-AIFM4C-F-5
1492-AIFM8-F-5
EA69
EB69
EC69
ED69
1492-AIFM16-F-3
1492-AIFM16-F-5
1492-AIFMQS
Cables are available in standard lengths of 0.5 m 1.0 m, 2.5 m, and 5.0 m. To order, insert the code for the desired cable length into the catalog number 005 = 0.5 m (010 = 1.0 m, 025 = 2.5 m, and 050 = 5.0 m), and insert the letter in the box. Example: Catalog Number 1492-ACAB025BA69 is for a 2.5 m cable, and the letters BA. Compatible Removable Terminal Block (RTB) plug; 1492-RTB8N (screw style terminals) or 1492-RTB8P (push-in style terminals, available March 2006). ORDER PLUGS SEPARATELY. Compatible Removable Terminal Block (RTB) plug; 1492-RTB12N (screw style terminals) or 1492-RTB12P (push-in style terminals, available March 2006). ORDER PLUGS SEPARATELY. Compatible Removable Terminal Block (RTB) plug; 1492-RTB16N (screw style terminals) or 1492-RTB16P (push-in style terminals, available March 2006). ORDER PLUGS SEPARATELY.
IR6
55
These pre-wired cables have a pre-wired RTB on one end to connect to the front of a Bulletin 1769 analog I/O module and a connector on the other end to plug into a 15- or 25-pin D-shell terminal AIFM. You must first select the AIFM from the preceding selection table.
Pre-Wired Cables for Bulletin 1769 Analog I/O Modules Cable Catalog Number 1492-ACABAA69 1492-ACABAB69 1492-ACABBA69 1492-ACABBB69 1492-ACABBC69 1492-ACABBD69 1492-ACABC69 1492-ACABD69 1492-ACABEA69 1492-ACABEB69 1492-ACABEC69 1492-ACABED69 Standard Cable Lengths 0.5, 1.0, 2.5, 5.0 m 0.5, 1.0, 2.5, 5.0 m 0.5, 1.0, 2.5, 5.0 m 0.5, 1.0, 2.5, 5.0 m 0.5, 1.0, 2.5, 5.0 m 0.5, 1.0, 2.5, 5.0 m 0.5, 1.0, 2.5, 5.0 m 0.5, 1.0, 2.5, 5.0 m 0.5, 1.0, 2.5, 5.0 m 0.5, 1.0, 2.5, 5.0 m 0.5, 1.0, 2.5, 5.0 m 0.5, 1.0, 2.5, 5.0 m Build-to-Order Available Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes AIFM Connector 15-pin D-shell 15-pin D-shell 15-pin D-shell 15-pin D-shell 15-pin D-shell 15-pin D-shell 25-pin D-shell 25-pin D-shell 25-pin D-shell 25-pin D-shell 25-pin D-shell 25-pin D-shell Mating 1769 I/O Module Catalog Number 1769-OF2 Voltage 1769-OF2 Current 1769-IF4 Single-Ended Voltage 1769-IF4 Single-Ended Current 1769-IF4 Differential Voltage 1769-IF4 Differential Current 1769-IR6 Resist. Temperature Detector 1769-OF8C, 1769-OF8V 1769-IF8 Single-Ended Voltage 1769-IF8 Single-Ended Current 1769-IF8 Differential Voltage 1769-IF8 Differential Current
Cables are available in standard lengths of 0.5 m, 1.0 m, 2.5 m, and 5.0 m. To order, insert the code for the desired cable length into the catalog number (005 = 0.5 m, 010 = 1.0 m, 025 = 2.5 m, and 050 = 5.0 m). Example: Catalog Number 1492-ACAB005 is for a 0.5 m cable.
56
Using Bulletin 1771 Selection Tables to Make Valid 1492 Wiring System Module Catalog Numbers
Follow these steps when using the selection tables to make valid catalog numbers: 1. Find the appropriate table based on the catalog number of the 1771 I/O module. 2. Find the column in the selected table for the 1771 I/O module. 3. Follow the column down to determine which Wiring System Modules are compatible with the I/O module as indicated by letter code. If there is no letter code, the Wiring System Module is not compatible with the I/O module. NOTE: The letter codes designate the compatible 1492 cable for that 1771 I/O and Wiring System Module combination. 4. Select the desired Wiring System Module. 5. Configure the cable catalog number using 1492-CABLE (for digital cables) or 1492-ACABLE (for analog cables). See footnote on pages 61 and 63.
57
IFMs for Bulletin 1771 Digital 8-Point and 16-Point I/O Modules
Catalog Number for Wiring System Module with Fixed Terminal Block Catalog Number for Wiring System Module with Removable Terminal Block Socket Assembly (order plugs separately 1492-RIFM20F 1492-RIFM20FN 1492-RIFM20F-2 I/O Module Catalog Number 1771- OND F F OAD OBD
Feed-through Standard 264V AC/DC Max. Narrow standard 132V AC/DC Max. Extra terminals (2 per I/O) 264V AC/DC Max. 3-wire sensor type input devices 132V AC/DC Max. LED Indicating Standard with 24V AC/DC LEDs Narrow standard with 24V AC/DC LEDs Standard with 120V AC/DC LEDs Narrow standard with 120V AC LEDs 24V AC/DC LEDs and extra terminals for outputs 24V AC/DC LEDs and extra terminals for inputs 120V AC LEDs and extra terminals for outputs 120V AC LEDs and extra terminals for inputs 3-wire sensor with 24V AC/DC LEDs 8 Individually isolated with 24/48V AC/DC LEDs and 4 terminals/output 8 Individually isolated with 120V AC LEDs and 4 terminals/output 240V AC LEDs and extra terminals for outputs 240V AC LEDs and extra terminals for inputs Fusible 120V AC/DC with extra terminals for outputs Extra terminals with 24V AC/DC blown fuse LED indicators Extra terminals with 120V AC/DC blown fuse LED indicators Extra terminals with 240V AC/DC blown fuse LED indicators Extra terminals with 24V AC/DC blown fuse LED indicators Extra terminals with 120V AC/DC blown fuse LED indicators 8 Individually isolated 120V AC/DC with extra terminals for outputs 8 Individually isolated with extra terminals and 24V AC/DC blown fuse LED indicators Two 4-point isolated groups with four terminals/input and 24V AC/DC blown fuse LED indicators 8 Individually isolated with extra terminals output, and 120V AC/DC blown fuse LED indicators 8 Individually isolated with four terminals/output and 120V AC/DC blown fuse LED indicators Two 4-point isolated groups with four terminals/input and 120V AC/DC blown fuse indicators 8 Individually isolated with 4 terminals/output and 240V AC/DC blown fuse indicators Relay Master (LED Indicating) 20-pin master with eight (8) 24V DC relays 20-pin master with eight (8) 120V AC relays 20-pin master with sixteen (16) 120V AC relays 20-pin master with sixteen (16) 120V AC relays with fusing 20-pin master relay with sixteen (16) 24V DC relays 20-pin master with sixteen (16) 24V DC relays with fusing
F F F F
F F F F
F F F F
F F F F
F F
F F F F
F F F
1492-IFM20D24 1492-IFM20D24N 1492-IFM20D120 1492-IFM20D120N 1492-IFM20D24-2 1492-IFM20D24A-2 1492-IFM20D120-2 1492-IFM20D120A-2 1492-IFM20D24-3 1492-IFM20DS24-4 1492-IFM20DS120-4 1492-IFM20D240-2 1492-IFM20D240A-2 1492-IFM20F-F-2 1492-IFM20F-F24-2 1492-IFM20F-F120-2 1492-IFM20F-F240-2 1492-IFM20F-F24A-2 1492-IFM20F-F120A-2 1492-IFM20F-FS-2 1492-IFM20F-FS24-2 1492-IFM20F-FS24A-4 1492-IFM20F-FS120-2 1492-IFM20F-FS120-4 1492-IFM20F-FS120A-4 1492-IFM20F-FS240-4
F F F
F F F F
F F F F
F F F
F F F F F
T T T T
T T
Note: Footnotes are on the following page. Publication 1492-TD008C-EN-P - September 2005
OMD F F
OGD
IMD
IND
IAD
IBD
IGD
ICD
IA2
IN
IA
IB
IH
IT
58
IFMs for Bulletin 1771 Digital 8-Point and 16-Point I/O Modules (Continued)
Description of 20-PIN IFM Catalog Number for Wiring System Module with Fixed Terminal Block Catalog Number for Wiring System Module with Removable Terminal Block Socket Assembly (order plugs separately I/O Module Catalog Number 1771- OND OAD OBD
Relay Expander (LED Indicating) Expander with eight (8) 24V DC relays Expander with eight (8) 120V AC relays Fusible Expander 8-channel expander with 24V DC blown fuse indicators 8-channel expander with 120V AC blown fuse indicators Feed-through Expander Expander with eight (8) feed-through channels
1492-XIMF-2
Either F or FF. One expander is connected to a master to provide a total of 16 outputs. An extender cable is included with each expander to connect it to the master. Cables are available in standard lengths of 0.5 m 1.0 m, 2.5 m, and 5.0 m. To order, insert the code for the desired cable length into the catalog number 005 = 0.5 m (010 = 1.0 m, 025 = 2.5 m, and 050 = 5.0 m), and insert the letter in the box. Example: Catalog Number 1492-CABLE050A is for a 5.0 m cable, and the letter A. This IFM is not recommended for use with PLC I/O modules that have an off-state leakage current exceeding 0.5 mA. Use a 1492-IFM20D120N or 1492-IFM20D120A-2 for inputs. Use 1492-IFM20D120-2 for outputs. The voltage rating is relay control/coil voltage. For Relay Contact Ratings, refer to page 186. The LED indicates the PLC output status. Compatible Removable Terminal Block (RTB) plug; 1492-RTB20N (screw style terminals) or 1492-RTB20P (push-in style terminals, available March 2006). ORDER PLUGS SEPARATELY. Compatible Removable Terminal Block (RTB) plug; 1492-RTB10N (screw style terminals) or 1492-RTB10P (push-in style terminals, available March 2006. ORDER PLUGS SEPARATELY.
OMD
OGD
IMD
IND
IAD
IBD
IGD
ICD
IA2
IN
IA
IB
IH
IT
59
IFMs for Bulletin 1771 Digital 16-Point Isolated and 32-Point I/O Modules
scOM16 M M M M M M scIM16 M Catalog Number for Wiring System Module with Fixed Terminal Block Catalog Number for Wiring System Module with Removable Terminal Block Socket Assembly (order plugs separately I/O Module Catalog Number 1771- OWNA L L L L L L L L
Feed-through Standard 132V AC/DC Max. Extra terminals (2 per I/O) 132V AC/DC Max. 3-wire sensor type input devices 60V AC/DC Max. LED Indicating Standard with 24V AC/DC LEDs 24V AC/DC LEDs and extra terminals for outputs 24V AC/DC LEDs and extra terminals for inputs 120V AC LEDs and extra terminals for outputs 120V AC LEDs and extra terminals for inputs 3-wire sensor with 24V AC/DC LEDs 16 Individually isolated with 24/48V AC/DC LEDs and 4 terminals/output 16 Individually isolated with 24V AC/DC LEDs and 4 terminals/input 16 Individually isolated with 120V AC LEDs and 4 terminals/output 16 Individually isolated with 120V AC LEDs and 4 terminals/input 16 Individually isolated with 240V AC LEDs and 4 terminals/input Fusible 120V AC/DC with extra terminals for outputs Extra terminals with 24V AC/DC blown fuse indicators for outputs Extra terminals with 120V AC/DC blown fuse indicators for outputs 16 Individually isolated with extra terminals for 120V AC DC outputs Individually isolated with extra terminals and 24V AC/DC blown fuse indicators for outputs 16 Individually isolated with 24V AC/DC blown fuse indicators and 4 terminals/output 16 Individually isolated 240V AC/DC with 4 terminals/output 16 Individually isolated with extra terminals and 120V AC/DC blown fuse indicators for outputs 16 Individually isolated with 120V AC/DC blown fuse indicators and 4 terminals/output 16 Individually isolated with 240V AC/DC blown fuse indicators and 4 terminals/output 16 Individually isolated with 24V AC/DC blown fuse indicators and 4 terminals/input 16 Individually isolated with 120V AC/DC 4 terminals/input 16 Individually isolated with 120V AC/DC blown fuse indicators and 4 terminals/input 16 Individually isolated with 240 VAC/DC blown fuse indicators and 4 terminals/input Relay Master (LED Indicating) 40-pin master with eight (8) 24V DC relays 40-pin master with sixteen (16) 24V DC relays 1492-XIM4024-8R 1492-XIM4024-16R 1492-RXIM4024-16R L L 1492-IFM40F-F-2 1492-IFM40F-F24-2 1492-IFM40F-F120-2 1492-IFM40F-FS-2 1492-IFM40F-FS24-2 1492-IFM40F-FS24-4 1492-IFM40F-FS-4 1492-IFM40F-FS120-2 1492-RIFM40F-F24-2 1492-RIFM40F-FS120-2 L L L L M M M M M M M M L L L L L 1492-IFM40D24 1492-IFM40D24-2 1492-IFM40D24A-2 1492-IFM40D120-2 1492-IFM40D120A-2 1492-IFM40D24-3 1492-IFM40DS24-4 1492-IFM40DS24A-4 1492-IFM40DS120-4 1492-IFM40DS120A-4 1492-IFM40DS240A-4 1492-RIFM40D24 1492-RIFM40D24A-2 J J J J M M K K K L L L M M M L L L L L 1492-IFM40F 1492-IFM40F-2 1492-IFM40F-3 1492-RIFM40F 1492-RIFM40F-2 J J J J J M M K K K L L L L M M M L L L L
1492-RIFM40F-FS120-4 1492-RIFM40F-FS120A4
M M
M M
OWN
OD16
OQ16
OAN
OBN
OVN
ODD
ID16
IQ16
IAN
IBN
IVN
60
IFMs for Bulletin 1771 Digital 16-Point Isolated and 32-Point I/O Modules (Continued)
Description of 40-PIN IFM scOM16 scIM16 Catalog Number for Wiring System Module with Fixed Terminal Block Catalog Number for Wiring System Module with Removable Terminal Block Socket Assembly (order plugs separately I/O Module Catalog Number 1771- OWNA
OW16
40-pin master with sixteen (16) 24V DC relays with fusing Relay Expander (LED Indicating) Expander with eight (8) 24V DC relays Expander with eight (8) 120V AC relays Fusible Expander 8-channel expander with 24V DC blown fuse indicators 8-channel expander with 120V AC blown fuse indicators Expander with sixteen (16) 24V DC relays with fusing Feed through Expander Expander with eight (8) feed-through channels
1492-XIM4024-16RF
1492-RXIM24-8R
1492-XIMF-2
Two or three expanders are connected to a master to provide a total of 32 outputs max (depends on PLC module). An extender cable is included with each expander to connect it to the master. One 1492-XIM24-16RF is to be used with one 1492-XIM4024-16R AND 1492-XIM4024-16RF master (32 PT. only). Cables are available in standard lengths of 0.5 m 1.0 m, 2.5 m, and 5.0 m. To order, insert the code for the desired cable length into the catalog number 005 = 0.5 m (010 = 1.0 m, 025 = 2.5 m, and 050 = 5.0 m), and insert the letter in the box. Example: Catalog Number 1492-CABLE025J is for a 2.5 m cable, and the letter J. For information concerning this I/O module contact Spectrum Controls (phone: 425-641-9473 or www.spectrumcontrols.com). Cable Catalog Number 1492-CAB has the N.O. contacts only connected. The voltage rating is relay control/coil voltage. For Relay Contact Ratings, refer to page 186. The LED indicates the PLC output status. Compatible Removable Terminal Block (RTB) plug; 1492-RTB20N (screw style terminals) or 1492-RTB20P (push-in style terminals, available March 2006). ORDER PLUGS SEPARATELY. Compatible Removable Terminal Block (RTB) plug; 1492-RTB17N (screw style terminals) or 1492-RTB17P (push-in style terminals, available March 2006). ORDER PLUGS SEPARATELY. Compatible Removable Terminal Block (RTB) plug; 1492-RTB14N (screw style terminals) or 1492-RTB14P (push-in style terminals, available March 2006). ORDER PLUGS SEPARATELY. Compatible Removable Terminal Block (RTB) plug; 1492-RTB12N (screw style terminals) or 1492-RTB12P (push-in style terminals, available March 2006). ORDER PLUGS SEPARATELY.
OWN
OD16
OQ16
OAN
OBN
ODD
OVN
ID16
IQ16
IAN
IBN
IVN
61
Pre-Wired Cables for Bulletin 1771 Digital I/O Modules Cable Catalog Number 1492-CABLEF 1492-CABLEFF 1492-CABLEJ 1492-CABLEK 1492-CABLEL 1492-CABLEM 1492-CABLER 1492-CABR71 1492-CABLET Standard Cable Lengths 0.5, 1.0, 2.5, 5.0 m 0.5, 1.0, 2.5, 5.0 m 0.5, 1.0, 2.5, 5.0 m 0.5, 1.0, 2.5, 5.0 m 0.5, 1.0, 2.5, 5.0 m 0.5, 1.0, 2.5, 5.0 m 0.5, 1.0, 2.5, 5.0 m 0.5, 1.0, 2.5, 5.0 m 0.5, 1.0, 2.5, 5.0 m Build-to-Order Available Yes Yes Yes Yes Yes Yes Yes Yes Yes No. of Conductors 20 20 40 40 40 40 40 40 20 Mating 1771 I/O Modules Catalog Number 1771-IAD, -IBD, -ICD, -IGD, -IND, -OAD, -OBD, -OGD, -OMD, -OND, -IMD 1771-OAD, -OBD, -OND 1771-IAN, -IBN 1771-IVN 1771-OAN, -OBN, -OVN, -OWN, -OWNA 1771-ID16, -IQ16, -OD16, -ODD, -OQ16, -SCIM16, -SCOM16 1771-OW16 1771-OW16 1771-IA, -IA2, -IB, -IH, -IN, -IT
Cables are available in standard lengths of 0.5 m, 1.0 m, 2.5 m, and 5.0 m. To order, insert the code for the desired cable length into the catalog number (005 = 0.5 m, 010 = 1.0 m, 025 = 2.5 m, and 050 = 5.0 m). Example: Catalog Number 1492-CABLE005M is for a 0.5 m cable that could be used to connect a Catalog Number 1492-IFM40F IFM to a Catalog Number 1771-ODD I/O module. Cable Catalog Number 1492-CABR71 has only the N.O. contacts connected.
The I/O module-ready cables have a wiring arm on one end to plug onto the front of a Bulletin 1771 I/O module and 20 or 40 individually colored #18 AWG conductors on the other end. These cables provide the convenience of pre-wired connections at the I/O module end, while still allowing the flexibility to field-wire to standard terminal blocks of your choice.
I/O Module-Ready Cables for 1771 Digital I/O Modules Cable Catalog Number 1492-CABLEWA Standard Build-to-Order No. of Mating 1771 Cable Lengths Available Conductors I/O Modules Catalog Number 1.0, 2.5, 5.0 m Yes 12 1771-IA, -IA2, -IB, -IC, -IH, -IM, -IN, -IT, -IV, -OA, -OB, -OC, -OM, -ON, -OP 1492-CABLEWD 1.0, 2.5, 5.0 m Yes 12 1771-ID, -ID01, -OD, -ODZ, -OR, -OW, -OYL, -OZL 1492-CABLEWH 1.0, 2.5, 5.0 m Yes 20 1771-IAD, -IBD, -ICD, -IGD, -IMD, -IND, -OAD, -OBD, -OGD, -OMD, -OND 1492-CABLEWHF 1.0, 2.5, 5.0 m Yes 20 1771-IBD , -OAD , -OBD , -OMD , -OND 1492-CABLEWN 1.0, 2.5, 5.0 m Yes 40 1771-IAN, -IBN, -ID16, -IQ16, -IVN, -OAN, -OBN, -OD16, -ODD, -OQ16, -OVN, -OW16, -OWN, -OWNA
Cables are available in standard lengths of 1.0 m, 2.5 m, and 5.0 m. To order, insert the code for the desired cable length into the catalog number (010 = 1.0 m, 025 = 2.5 m, and 050 = 5.0 m). Example: Catalog Number 1492-CABLE050WN is for a 5.0 m cable with a pre-wired Catalog Number 1771-WN wiring arm on one end. Includes an optional 3 A fuse in the Wiring Arm for 1771 PLC mating I/O Modules. Discrete I/O ready cables should not be used with PLC analog I/O modules as a cable shield and drain wires are not provided.
62
IFE (Single-Ended)
IFF (Single-Ended)
IFE (Differential)
IFF (Differential)
Catalog Number for Wiring System Module with Fixed Terminal Block
OFE1
OFE2 G
Feed-through 4-channel input, output or 2 in/2 out combination with 3 terminals/channel 6-channel isolated with 34 terminals/channel 8-channel differential 16-channel single-ended with 3 terminals/channel Thermocouple 6-channel with 3 terminals/channel Fusible 4-channel with 24V DC blown fuse indicators, test points, 5 terminals/input 2-channel/input, 2-channel/output with 24V DC blown fuse indicators, test points, 5 terminals/input, 3 terminals/ output 8-channel Input with 24V DC blown fuse indicators, 5 terminals/channel 16-channel Input with 24V DC blown fuse indicators, 3 terminals/channel 16-channel Input with 24V DC blown fuse indicators, 5 terminals/channel 4-input /4-output channel with 8 fuses and 24V blown fuse indicators
F F
F F
Cables are available in standard lengths of 0.5 m, 1.0 m, 2.5 m, and 5.0 m. To order, insert the code for the desired cable length into the catalog number 005 = 0.5 m (010 = 1.0 m, 025 = 2.5 m, and 050 = 5.0 m), and insert the letter in the box. Example: Catalog Number 1492-ACABLE025H is for a 2.5 m cable, and the letter H. Cannot be used with 1771 I/O. Compatible Removable Terminal Block (RTB) plug; 1492-RTB8N (screw style terminals) or 1492-RTB8P (push-in style terminals, available March 2006). ORDER PLUGS SEPARATELY. Compatible Removable Terminal Block (RTB) plug; 1492-RTB12N (screw style terminals) or 1492-RTB12P (push-in style terminals, available March 2006). ORDER PLUGS SEPARATELY. Compatible Removable Terminal Block (RTB) plug; 1492-RTB16N (screw style terminals) or 1492-RTB16P (push-in style terminals, available March 2006). ORDER PLUGS SEPARATELY.
These pre-wired cables have a wiring arm on one end to connect to the front of a Bulletin 1771 analog I/O module and a connector on the other end to plug into a 15- or 25-pin D-shell terminal AIFM. You must first select the AIFM from the preceding selection table
OFE3 G
Catalog Number for Wiring System Module with Removable Terminal Block Socket Assembly (order plugs separately
IR
IL
63
.
Pre-Wired Cables for Bulletin 1771 Analog I/O Modules Cable Catalog Number 1492-ACABLEE 1492-ACABLEF 1492-ACABLEG 1492-ACABLEH 1492-ACABLEJ Standard Cable Lengths 0.5, 1.0, 2.5, 5.0 m 0.5, 1.0, 2.5, 5.0 m 0.5, 1.0, 2.5, 5.0 m 0.5, 1.0, 2.5, 5.0 m 0.5, 1.0, 2.5, 5.0 m Build-to-Order Available Yes Yes Yes Yes Yes AIFM Connector 25-pin D-shell 25-pin D-shell 15-pin D-shell 25-pin D-shell 25-pin D-shell Mating 1771 I/O Modules 1771-IFE, -IFF Differential 1771-IFE, -IFF Single-Ended 1771-OFE1, -OFE2, -OFE3 1771-IL 1771-IR
Cables are available in standard lengths of 0.5 m, 1.0 m, 2.5 m, and 5.0 m. To order, insert the code for the desired cable length into the catalog number (005 = 0.5 m, 010 = 1.0 m, 025 = 2.5 m, and 050 = 5.0 m). Example: Catalog Number 1492-ACABLE005E is for a 0.5 m cable that could be used to connect a Catalog Number 1492-AIFM8-3 IFM to a Catalog Number 1771-IFE I/O module. Build-to-order lengths are also available.
64
IFM-Ready I/O Cable Cable Catalog Number 1492-CABLEP 1492-CABLEQ Standard Cable Lengths 1.0, 2.5, 5.0 m 1.0, 2.5, 5.0 m Insulation Rating 300V, 80C 300V, 80C No. Conductors 20 40 Conductor Nominal Outer Size Diameter 22 AWG 22 AWG 9 mm (0.36 in.) 11.7 mm (0.46 in.) Current/ Conductor 2A 2A Compatible IFM Catalog Numbers 1492-IFM20, 1492-XIM20 1492-IFM40, 1492-XIM40
Cables are available in lengths of 1.0 m, 2.5 m, and 5.0 m. To order, insert the desired cable length into the catalog number (010 = 1.0 m, 025 = 2.5 m, and 050 = 5.0 m). Example: Catalog Number 1492-CABLE025P is for a 2.5 m, 20 conductor IFM-ready cable. Also refer to Build-to-Order Length Cables on page 64.
All Bulletin 1492 cables are available in build-to-order lengths. Consult your distributor for availability.
65
Page No. for IFM Specifications Catalog Number 210 210 210 210 210 210 210 210 210 210 210 210 210 210 210 210 210 210 210 210 210 210 211 1492-IFM20D240A-2 1492-IFM20F-F240-2 1492-IFM20F-FS240-4 1492-IFM20DS24-4 1492-IFM20F-F-2, -RIFM20F-F-2 1492-IFM20F-FS-2 1492-IFM40F, -RIFM40F 1492-IFM40F-2, RIFM40F-2 1492-IFM40F-F-2 1492-IFM40F-FS-2 1492-IFM40F-FSA-4 1492-IFM40F-FS-4 1492-IFM40F-3 1492-IFM40DS24-4 1492-IFM40D24, -RIFM40D24 1492-IFM40D24-2 1492-IFM40D24A-2, -RIFM40D24A-2 1492-IFM40D24-3 1492-IFM40DS24A-4 1492-IFM40F-F24-2, -RIFM40F-F24-2 1492-IFM40F-FS24-2 1492-IFM40D120A-2 1492-IFM40D120-2 1492-IFM40DS120-4
Page No. for Application Notes and Pinout 73 79 85 75 77 80 86 86 99 104 111 105 87 94 88 89 90 93 95 100 104 92 91 96
Page No. for IFM Specifications Catalog Number 211 211 211 212 211 211 211 211 211 211 211 213 212 212 212 212 212 212 212 212 212 213 213 213 1492-IFM40DS120A-4 1492-IFM40F-F120-2 1492-IFM40F-FS120-2, -RIFM40F-FS120-2 1492-IFM40F-FS120-4, -RIFM40F-FS120-4 1492-IFM40F-FS120A-4, -RIFM40F-FS120A-4 1492-IFM40DS240A-4 1492-IFM40F-FS240-4 1492-XIM4024-16R, -RXIM4024-16R 1492-XIM4024-16RF 1492-XIM4024-8R 1492-XIM2024-8R 1492-XIM2024-16R 1492-XIM2024-16RF 1492-XIM24-8R, -RXIM24-8R 1492-XIM24-16RF 1492-XIMF-F24-2 1492-XIM20120-16R 1492-XIM20120-16RF 1492-XIM20120-8R 1492-XIM120-8R 1492-XIMF-F120-2 1492-XIMF-2
Page No. for Application Notes and Pinout 97 103 107 108 111 98 109 112 123 119 119 115 116 124 128 129 117 118 114 126 131 133
Page No. for Specifications 117 213 213 213 213 213 213 214 214 214 215 215 215 215 215 215 215 215 215 215 215 215
For all IFM dimensions, refer to page 174. For general Adhesive Label Card information, refer to page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web page at http://www.ab.com/catalogs/RAISE. Refer to page 200 for specific platform web site information. Refer to the online documentation for new product information.
66
Symbols and Terminal Identification Conventions Used Throughout the Pinout Section
Fuse and Blown Fuse Indicator (where applicable) LED Circuit LED Indicator Connector Pin Field-Side Terminal N.C./N.O. Relay Contact
~ ~
67
1492-IFM20F 1492-RIFM20F
Feed-Through Standard 264V AC/DC Max.
1492-IFM20FN 1492-RIFM20FN
Feed-Through Narrow Standard 132V AC/DC Max.
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Dimensions Refer to page 181.
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Dimensions Refer to page 181.
Pinout
1 2 3 A1 A2 A3
Pinout
2 11 B1 B2
18 19 20
18 20
B9 B10
1 3
A1 A2
10 19
A9 A10
68
1492-IFM20F-2 1492-RIFM20F-2
Feed-Through Extra Terminals (2 per I/O) 264V AC/DC Max.
1492-IFM20F-3
Feed-Through 3-Wire Sensor Type Input Devices 132V AC/DC Max.
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Isolation The power bus is isolated into two groups of 10 terminals. This allows each group of the I/O devices to reference a different power source. 4. Dimensions Refer to page 181.
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Isolation The power busses are connected to one common (one bus has 17 terminals, and one bus has 18 terminals). All of the input devices used must reference the same power source. 4. Dimensions Refer to page 181.
Pinout
1 2 3 B1 B2 B3
Pinout
3
C1
18
C16
B1
18 19 20
B2
20
B17
A1 A2
A11 A12
B18
A1 A2
A9 A10
A19 A20
A16 A17
A18
69
1492-IFM20D24
LED Indicating Standard with 24V AC/DC LEDs
1492-IFM20D24N
LED Indicating Narrow Standard with 24V AC/DC LEDs
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. When this IFM is used with a hard contact (relay) output circuit that switches an inductive load, surge suppression must be used (e.g., a 1N4004 diode reverse-wired across a DC load). 2. Wiring The LEDs are powered from the two-position terminal block. Make only one connection to the power source for normal operation. Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Isolation The LEDs are broke into two separate groups. Group 1 is commoned at terminal Test 0-7 and Group 2 is commoned at terminal Test 8-15. 4. Dimensions Refer to page 181.
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. When this IFM is used with a hard contact (relay) output circuit that switches an inductive load, surge suppression must be used (e.g., a 1N4004 diode reverse-wired across a DC load). 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Isolation The LEDs are connected to one common. All of the I/O devices must reference the same power source. 4. Dimensions Refer to page 181.
Pinout
2 11 B1 B2
Pinout
1 2 3 A1 A2 A3
18 20
B9 B10
1 3
A1 A2
18 19 20
A 18 A 19 A 20
10 19 A9 A10
~ ~
~ ~
LED Circuit
L E D 8 -1 5 L E D 0 -7
70
1492-IFM20D120
LED Indicating Standard with 120V AC/DC LEDs
1492-IFM20D120N
LED Indicating Narrow Standard with 120V AC LEDs
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. This IFM is not recommended for use with input devices or programmable controller output circuits having an off-state leakage current exceeding 0.5 mA. Use Cat. No. 1492-IFM20D120N instead, or use Cat. No. 1492-IFM20D120A-2 for input modules and Cat. No. 1492-IFM20D120-2 for output modules. When this IFM is used with a hard contact (relay) output circuit that switches an inductive load, surge suppression must be used (e.g., a 1N4004 diode reverse-wired across a DC load). 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Isolation The LEDs are isolated into two groups of eight terminals. This allows each group of the I/O devices to reference a different power source. 4. Dimensions Refer to page 181.
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. When this IFM is used with a hard contact (relay) output circuit that switches an inductive load, surge suppression must be used (e.g., a 1N4004 diode reverse-wired across a DC load). 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Isolation The LEDs are connected to one common. All of the I/O devices must reference the same power source. 4. Dimensions Refer to page 181.
Pinout
2 11 B1 B2
18
20
B9
B10
Pinout
1 2 3 A1 A2 A3
A1
10
A10
A2
11
A11
10
18 19 20 A18 A19 A20
A9
A10
19
LED Circuit
L2 (-) L2 (-)
71
1492-IFM20D24-2
LED Indicating 24V AC/DC LEDs & Extra Terminals for Outputs
1492-IFM20D24A-2
LED Indicating 24V AC/DC LEDs & Extra Terminals for Inputs
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. When this IFM is used with a hard contact (relay) output circuit that switches an inductive load, surge suppression must be used (e.g., a 1N4004 diode reverse-wired across a DC load). 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Isolation The power bus and LEDs are isolated into two groups of 10 terminals (eight LEDs). This allows each group of output devices to reference a different power source. 4. Dimensions Refer to page 181.
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. When this IFM is used with a hard contact (relay) output circuit that switches an inductive load, surge suppression must be used (e.g., a 1N4004 diode reverse-wired across a DC load). 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Isolation The power bus comprises 20 terminals connected together. The LEDs are connected to one common. All of the I/O devices must reference the same power source. 4. Dimensions Refer to page 181.
Pinout
1 2 3 B1 B2 B3
Pinout
1 2 3 B1 B2 B3
10
B10
11
B11
18 19 20
18 19 20
A1
A11
A2
A12
A1
A9 A19
A10
A20
LED Circuit
A2
LED Circuit
A19
A20
72
1492-IFM20D120-2
LED Indicating 120V AC LEDs & Extra Terminals for Outputs
1492-IFM20D120A-2
LED Indicating 120V AC LEDs & Extra Terminals for Inputs
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. When this IFM is used with a hard contact (relay) output circuit that switches an inductive load, surge suppression must be used (e.g., an MOV wired across an AC load). 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Isolation The power bus and LEDs are isolated into two groups of 10 terminals (8 LEDs). This allows each group of output devices to reference a different power supply. 4. Dimensions Refer to page 181.
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. When this IFM is used with a hard contact (relay) output circuit that switches an inductive load, surge suppression must be used (e.g., an MOV wired across an AC load). 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Isolation The power bus comprises 20 terminals connected together. The LEDs are connected to one common. All of the I/O devices must reference the same power source. 4. Dimensions Refer to page 181.
Pinout
1 2 3 B1 B2 B3
Pinout
1 2
10 B10
B1 B2 B3
11
B11
18 19 20
18 19 20
A1
A11
A2
A12
A1
A9 A19
A10
A20
LED Circuit
A2
LED Circuit
A19
A20
73
1492-IFM20D240-2
LED Indicating 240V AC LEDs & Extra Terminals for Outputs
1492-IFM20D240A-2
LED Indicating 120V AC LEDs & Extra Terminals for Inputs
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. When this IFM is used with a hard contact (relay) output circuit that switches an inductive load, surge suppression must be used (e.g., an MOV wired across an AC load). 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Isolation The power bus and LEDs are isolated into two groups of 10 terminals (8 LEDs). This allows each group of output devices to reference a different power supply. 4. Dimensions Refer to page 181.
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. When this IFM is used with a hard contact (relay) output circuit that switches an inductive load, surge suppression must be used (e.g., an MOV wired across an AC load). 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Isolation The power bus comprises 20 terminals connected together. The LEDs are connected to one common. All of the I/O devices must reference the same power source. 4. Dimensions Refer to page 181.
Pinout
1 2 3 B1 B2 B3
Pinout
1 2 3
10 11 B10 B11
B1 B2 B3
18
18 19 20 B18 B19 B20
19 20
A1
A11 A12
LED Circuit
A2
LED Circuit
A19 A20
A9 A10
A19 A20
74
1492-IFM20D24-3
LED Indicating 3-Wire Sensor with 24V AC/DC LEDs
Pinout
3 C1
18
C16
B1 B2 1 2 19 20
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. When this IFM is used with a hard contact (relay) output circuit that switches an inductive load, surge suppression must be used. 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Isolation The LEDs are connected to one common. All of the field input devices must reference the same power source. 4. Dimensions Refer to page 181.
B17 B18
A1 A2
LED Circuit
A17 A18
75
1492-IFM20DS24-4
LED Indicating 8 Individually Isolated with 24/48V AC/DC LEDs & 4 Terminals/Output
Pinout
10 B1 B2 2 (even) 8 12 (even) 18 3 (odd) B10 B11 B6 B7 B3
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. When this IFM is used with a hard contact (relay) output circuit that switches an inductive load, surge suppression must be used. 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Isolation There are eight individually isolated channels. LED returns are individually isolated. 4. Extra Terminals Two field-side terminals are internally connected on the IFM for each channel, and are available for power source common connections. 5. Dimensions Refer to page 181.
9 11 (odd) 17 20
B14 B15
A1 A2 A3 A4
76
1492-IFM20DS120-4
LED Indicating 8 Individually Isolated with 120V AC LEDs & 4 Terminals/Output
Pinout
10
B1 B2
B3
B6 B7
B10 B11
B14 B15
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. When this IFM is used with a hard contact (relay) output circuit that switches an inductive load, surge suppression must be used (e.g., an MOV wired across an AC load). 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Isolation There are eight individually isolated channels. LED returns are individually isolated. 4. Extra Terminals Two field-side terminals are internally connected on the IFM for each channel, and are available for power source common connections. 5. Dimensions Refer to page 181.
17 20
A1 A2 A3 A4
A17 A18
19
A19 A20
77
1492-IFM20F-F-2 1492-RIFM20F-F-2
Fusible Extra Terminals for Outputs
1492-IFM20F-F24-2 1492-RIFM20F-F24-2
Fusible Extra Terminals with 24V AC/DC Blown Fuse Indicators
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Fusing Fuse holders are included with the IFM. Fuses (5 x 20 mm) are not included. 4. Isolation The power bus and fuse clips are isolated into two groups of 10 terminals (eight fuse clips). This allows each group of output devices to reference a different power source. 5. Dimensions Refer to page 181.
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. When this IFM is used with a hard contact (relay) output circuit that switches an inductive load, surge suppression must be used. 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Fusing Fuse holders are included with the IFM. Fuses (5 x 20 mm) are not included. 4. Isolation The power bus, fuse clips, and blown fuse indicators are isolated into two groups of 10 terminals (eight fuse clips and blown fuse indicators). This allows each group of output devices to reference a different power source. 5. Dimensions Refer to page 181.
Pinout
1 2 3 B1 B2 B3
Pinout
1 B1 B2 B3
18 19 20
2 3
A1 A2
A11 A12
18 19 20 A1 A2 A11 A12
A9 A10
A19 A20
A9 A10 A19 A20
78
1492-IFM20F-F24A-2 1492-RIFM20F-F24A-2
Fusible Extra Terminals with 24V AC/DC Blown Fuse Indicators
1492-IFM20F-F120-2 1492-RIFM20F-F120-2
Fusible Extra Terminals with 120V AC/DC Blown Fuse Indicators
Pinout
1 2 3 B1 B2 B3
Pinout
1 2 3
B1 B2 B3
18 19 20
18 19 20
A1 A2
A1 A2
A11 A12
A3
A9
A10
A19 A20
A10
A11
A18
79
1492-IFM20F-F120A-2 1492-RIFM20F-F120A-2
Fusible Extra Terminals with 120V AC/DC Blown Fuse Indicators
1492-IFM20F-F240-2
Fusible Extra Terminals with 240V AC/DC Blown Fuse Indicators
Pinout
1 B1 B2 B3
Pinout
1 2 3 B1 B2 B3
2 3
18 19 20
18 19 20
A1 A2
A1 A2
A11 A12
A3
A9
A10
A19 A20
A10
A11
A18
A19 A20
80
1492-IFM20F-FS-2
Fusible 8 Individually Isolated 120V AC/DC with Extra Terminals for Outputs
1492-IFM20F-FS24-2
Fusible 8 Individually Isolated with Extra Terminals and 24V AC/DC Blown Fuse Indicators
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Fusing Fuse holders are included with the IFM. Fuses (5 x 20 mm) are not included. 4. Isolation The fuse clips are isolated into eight groups of terminals. This allows each output device to reference a different power source. 5. Dimensions Refer to page 181.
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. When this IFM is used with a hard contact (relay) output circuit that switches an inductive load, surge suppression must be used (e.g., a 1N4004 diode reverse-wired across a DC load). 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Fusing Fuse holders are included with the IFM. Fuses (5 x 20 mm) are not included. 4. Isolation The fuse clips and blown fuse indicators are isolated into eight groups of terminals. This allows each output device to reference a different power source. 5. Dimensions Refer to page 181.
Pinout
10 3 5 (odd) 15 17 20 B8 B9 B10 B1 B2 B3
Pinout
10 3 5 (odd) 15 17 B8 B9 B10 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 B1 B2 B3
1 2 4 6 8 12 14 16 18 19
A1 A2 A3 A4 A5 A6 A7 A8 A9 A10
20 1 2 4 6 8 12 14 16 18 19
81
1492-IFM20F-FS24A-4
Fusible Two 4-Point Isolated Groups with 4 Terminals/Input and 24V AC/DC Blown Fuse LED Indicators
Pinout
3 4 5 6 15 16 17 18 B6 B7 B8 B9 B10 B11 B12 B13 B1 B2 B3 B4 7 B5
Application Notes
A1
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. When this IFM is used with a hard contact (relay) output circuit that switches an inductive load, surge suppression must be used (e.g., a 1N4004 diode reverse-wired across a DC load). 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Fusing Fuse holders are included with the IFM. Fuses (5 x 20 mm) are not included. 4. Isolation The fuse clips and blown fuse indicators are isolated into two groups of terminals. This allows each group of output devices to reference a different power source. 5. Dimensions Refer to page 181.
A2 A3 A4 11 A5 B14
A6 A7 A8 A9
82
1492-IFM20F-FS120-2
Fusible 8 Individually Isolated with Extra Terminals and 120V AC/DC Blown Fuse LED Indicators
Pinout
10 3 5 (odd) 15 17 20 1 2 4 6 8 12 B8 B9 B10 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 B1 B2 B3
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. When this IFM is used with a hard contact (relay) output circuit that switches an inductive load, surge suppression must be used (e.g., an MOV wired across an AC load). 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Fusing Fuse holders are included with the IFM. Fuses (5 x 20 mm) are not included. 4. Isolation The fuse clips and blown fuse indicators are isolated into eight groups of terminals. This allows each output device to reference a different power source. 5. Dimensions Refer to page 181.
14 16 18 19
83
1492-IFM20F-FS120-4
Fusible 8 Individually Isolated with 4 Terminals/Output and 120V AC/DC Blown Fuse LED Indicators
Pinout
2 3 A3 1 B3 4 5 A4 B4 6 7 A5 B5 8 9 A14 B14 A6 B6 A13 B13 A12 B12 A11 B11
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. When this IFM is used with a hard contact (relay) output circuit that switches an inductive load, surge suppression must be used (e.g., an MOV wired across an AC load). 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Fusing Ten fuse holders are included with the IFM. Fuses (5 x 20 mm) are not included. 4. Isolation The fuse clips and blown fuse indicators are isolated into eight groups of terminals. This allows each output device to reference a different power source. 5. Dimensions Refer to page 181.
12 11
A15 B15 A7
84
1492-IFM20F-FS120A-4
Fusible Two 4-Point Isolated Groups with 4 Terminals/Input and 120V AC/DC Blown Fuse LED Indicators
Pinout
3 4 5 6 15 16 17 18 B6 B7 B8 B9 B10 B11 B12 B13 B1 B2 B3 B4 7 B5
A1 A2
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. When this IFM is used with a hard contact (relay) output circuit that switches an inductive load, surge suppression must be used (e.g., a 1N4004 diode reverse-wired across a DC load or an MOV across an AC load). 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Fusing Ten fuse holders are included with the IFM. Fuses (5 x 20 mm) are not included. 4. Isolation The fuse clips and blown fuse indicators are isolated into two groups of terminals. This allows each group of input devices to reference a different power source. 5. Dimensions Refer to page 181.
11
A3 A4 A5 B14
A6 A7 A8 A9
85
1492-IFM20F-FS240-4
Fusible 8 Individually Isolated with 4 Terminals/Output and 240V AC/DC Blown Fuse LED Indicators
Pinout
2 3 A3 1 B3 4 5 A4 B4 6 7 A5 B5 8 9 A6 B6 A14 B14 A13 B13 A12 B12 A11 B11
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. When this IFM is used with a hard contact (relay) output circuit that switches an inductive load, surge suppression must be used (e.g., a 1N4004 diode reverse-wired across a DC load or an MOV across an AC load). 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Fusing Fuse holders are included with the IFM. Fuses (5 x 20 mm) are not included. 4. Isolation The fuse clips and blown fuse indicators are isolated into eight groups of terminals. This allows each output device to reference a different power source. 5. Dimensions Refer to page 181.
12 11 A7 19 B7 14 13 A8 B8 16 15 A9 B9 18 17 A10 B10
A15 B15
A16 B16
A17 B17
A18 B18
86
1492-IFM40F 1492-RIFM40F
Feed-Through Standard 132V AC/DC
1492-IFM40F-2 1492-RIFM40F-2
Feed-Through Extra Terminals (2 per I/O) 132V AC/DC
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Dimensions Refer to page 181.
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Isolation The power bus is isolated into four groups of 10 terminals. This allows each group of the I/O devices to reference a different power source. 4. Dimensions Refer to page 181.
Pinout
1 3 5 (odd) 35 37 39
A1 A2 A3
Pinout
1 3 5 (odd) 35 37 39 B18 B19 B20 B1 B2 B3
2 4 6 (even) 36 38 40
B1 B2 B3
2 4 6 (even) B21 B22 B23
36 38 40
A1
A11
A21
A31
A2
A12
A22
A32
A9
A19
A29
A39
A10
A20
A30
A40
87
1492-IFM40F-3
Feed-Through 3-Wire Sensor Type Input Devices 60V AC/DC
Pinout
TB1
5
(odd) 35
C1
C16 B1 B2
TB2
1 3
37 39
B17 B18 A1 A2
TB1
A17 A18
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Isolation The power busses are isolated into two groups of 18 terminals. This allows the input devices connected to the left field-side terminal block to reference a different power source than the input devices connected to the right field-side terminal block. 4. Dimensions Refer to page 181.
TB2
6
(even) 36
C1
C16 B1 B2
2 4
38 40
88
1492-IFM40D24 1492-RIFM40D24
LED Indicating Standard with 24V AC/DC LEDs
Pinout
1 3 5 (odd) 35 37 39 A18 A19 A20 A1 A2 A3
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. When this IFM is used with a hard contact (relay) output circuit that switches an inductive load, surge suppression must be used (e.g., a 1N4004 diode reverse-wired across a DC load). 2. Wiring The LEDs are powered off the two-position terminal block. Make only one connection to the power source for normal operation. Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Isolation The LEDs are connected to one common. All of the I/O devices used must reference the same power source. 4. Dimensions Refer to page 181.
2 4 6 (even) 36 38 40
B1 B2 B3
89
1492-IFM40D24-2
LED Indicating24V AC/DC LEDs and Extra Terminals for Outputs
Pinout
1 3 5 (odd) 19 21 (odd) 35 37 39 B18 B19 B20 B10 B11 B1 B2 B3
A1 A2
A11 A12
A9 A10 2 4 6 (even) 20
B30 B31
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. When this IFM is used with a hard contact (relay) output circuit that switches an inductive load, surge suppression must be used (e.g., a 1N4004 diode reverse-wired across a DC load). 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Isolation The power bus and LEDs are isolated into four groups of 10 terminals (eight LEDs). This allows each group of output devices to reference a different power source. 4. Dimensions Refer to page 181.
22 (even) 36 38 40
A21
A31 A32
LED Circuit
A22
A29 A30
A39 A40
90
1492-IFM40D24A-2 1492-RIFM40D24A-2
LED Indicating24V AC/DC LEDs and Extra Terminals for Inputs
Pinout
1 3 5 (odd) 19 21 (odd) 35 37 39 A1 A2 A11 A12 B18 B19 B20 B10 B11 B1 B2 B3
A9 A10 2 4 6 (even)
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. When this IFM is used with a hard contact (relay) output circuit that switches an inductive load, surge suppression must be used (e.g., a 1N4004 diode reverse-wired across a DC load). 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Isolation The power bus and LEDs are isolated into four groups of 10 terminals (eight LEDs). This allows each group of input devices to reference a different power source. 4. Dimensions Refer to page 181.
B30 B31
LED Circuit
A22
A29 A30
A39 A40
91
1492-IFM40D120-2
LED Indicating 120V AC LEDs and Extra Terminals for Outputs
Pinout
1 1 3 3 5 5 (odd) (odd) 19 19 21 21 (odd) (odd) 35 35 37 37 39 39 B1 B1 B2 B2 B3 B3 B10 B10 B11 B11 B18 B18 B19 B19 B20 B20
A11 A11 A12 A12 A19 A19 A20 A20 B21 B21 B22 B22 B23 B23 B30 B30 B31 B31 B38 B38 B39 B39 B40 B40
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. When this IFM is used with a hard contact (relay) output circuit that switches an inductive load, surge suppression must be used (e.g., an MOV wired across an AC load). 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Isolation The power bus and LEDs are isolated into four groups of 10 terminals (eight LEDs). This allows each group of output devices to reference a different power source. 4. Dimensions Refer to page 181.
LED Circuit
92
1492-IFM40D120A-2
LED Indicating 120V AC LEDs and Extra Terminals for Inputs
Pinout
1 1 3 5
3 5 (odd) 19 21 B10 B1 B2 B3
B1 B2 B3
(odd) 19
B10
B11
21 (odd) (odd)
37 35 B18 B19 B20 A1 A2 A11 A12
B11
35 37 39
39
A1
A9 A19
A11 A12
A20 B21
A2
A10 2 4 6
A9 A10
A19
B22
A20B23 B21
B30 B31
2 (even) 4 20 6 22
B22 B23
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. When this IFM is used with a hard contact (relay) output circuit that switches an inductive load, surge suppression must be used (e.g., an MOV wired across an AC load). 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Isolation The power bus and LEDs are isolated into four groups of 10 terminals (eight LEDs). This allows each group of input devices to reference a different power source. 4. Dimensions Refer to page 181.
(even) (even) 20 36
38 B38 B39 B40 A21 A22 A31 A32
B30 B31
22 40 (even) 36 38
A29 A39
40
A30 A40
A21 A22
A31 A32
LED Circuit
A29 A30
A39 A40
93
1492-IFM40D24-3
LED Indicating 3-Wire Sensor with 24V AC/DC LEDs
Pinout
TB1
5 (odd) 35 C16 C1
TB2
1 3 37 39 B17 B18 A1 A2 B1 B2
TB1
A17 A18
TB2
6 (even) 36 C16 C1
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. When this IFM is used with a hard contact (relay) output circuit that switches an inductive load, surge suppression must be used (e.g., a 1N4004 diode reverse-wired across a DC load). 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Isolation The power busses and LEDs are isolated into two groups of 18 terminals (16 LEDs). This allows the input devices connected to the left field-side terminal block to reference a different power source than the input devices connected to the right field-side terminal block. 4. Dimensions Refer to page 181.
B1 B2
2 4 38 40
B17 B18 A1 A2
LED Circuit
A17 A18
94
1492-IFM40DS24-4
LED Indicating 16 Individually Isolated with 24/48V AC/DC LEDs and 4 Terminals/Output
Pinout
5 (odd) 19 21 (odd) 35 6 (even) 20 22 (even) 36 B24 B16 B17 B32 B9 B8 B25 B1
A1
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. When this IFM is used with a hard contact (relay) output circuit that switches an inductive load, surge suppression must be used (e.g., a 1N4004 diode reverse-wired across a DC load). 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Isolation There are 16 individually isolated channels. LED returns are individually isolated. 4. Extra Terminals Two field-side terminals are internally connected on the IFM for each channel, and are available for power source common connections. 5. Dimensions Refer to page 181.
A2
A31 A32
95
1492-IFM40DS24A-4
LED Indicating 16 Individually Isolated with 24V AC/DC LEDs and 4 Terminals/Input
Pinout
6 6 (even) (even) 20 20 B16 B16 B9 B9
B1 B1
B8 B8 B17 B17
B24 B24
Application Notes
21 21 B25 B25
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. When this IFM is used with a hard contact (relay) output circuit that switches an inductive load, surge suppression must be used (e.g., a 1N4004 diode reverse-wired across a DC load). 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Isolation There are 16 individually isolated channels. LED returns are individually isolated. 4. Extra Terminals Two field-side terminals are internally connected on the IFM for each channel, and are available for power source common connections. 5. Dimensions Refer to page 181.
96
1492-IFM40DS120-4
LED Indicating 16 Individually Isolated with 120V AC and 4 Terminals/Output
Pinout
5 (odd) 19 21 (odd) 35 6 (even) 20 22 (even) 36 B24 B16 B17 B32 B9 B8 B25 B1
A1
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. When this IFM is used with a hard contact (relay) output circuit that switches an inductive load, surge suppression must be used (e.g., an MOV wired across an AC load). 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Isolation There are 16 individually isolated channels. LED returns are individually isolated. 4. Extra Terminals Two field-side terminals are internally connected on the IFM for each channel, and are available for power source common connections. 5. Dimensions Refer to page 181.
A2
A31 A32
97
1492-IFM40DS120A-4
LED Indicating 16 Individually Isolated with 120V AC LEDs and 4 Terminals/Input
Pinout
6 (even) 20 B16 B9
5 (odd) 19 22 (even) 36
B1
B8 B17
B24
Application Notes
21 B25 (odd) 35 B32 A1 A2
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. When this IFM is used with a hard contact (relay) output circuit that switches an inductive load, surge suppression must be used (e.g., an MOV wired across an AC load). 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Isolation There are 16 individually isolated channels. LED returns are individually isolated. 4. Extra Terminals Two field-side terminals are internally connected on the IFM for each channel, and are available for power source common connections. 5. Dimensions Refer to page 181.
A31 A32
98
1492-IFM40DS240A-4
LED Indicating 16 Individually Isolated with 240V AC LEDs and 4 Terminals/Input
Pinout
6 (even) 36 B32 B17
5 (odd) 35
A17
A32
A1 B1
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. When this IFM is used with a hard contact (relay) output circuit that switches an inductive load, surge suppression must be used (e.g., an MOV wired across an AC load). 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Isolation There are 16 individually isolated channels. LED returns are individually isolated. 4. Extra Terminals Two field-side terminals are internally connected on the IFM for each channel, and are available for power source common connections. 5. Dimensions Refer to page 181.
A16 B16
99
1492-IFM40F-F-2
Fusible 120V AC/DC with Extra Terminals for Outputs
Pinout
1 3 5 (odd) 35 37 39 B18 B19 B20 B1 B2 B3
2 4 6 (even)
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Fusing Fuse holders are included with the IFM. Fuses (5 x 20 mm) are not included. 4. Isolation The power bus and fuse clips are isolated into four groups of 10 terminals (eight fuse clips). This allows each group of output devices to reference a different power source. 5. Dimensions Refer to page 181.
36 38 40
A1 A2
A11 A12
A21 A22
A31 A32
A9 A10
A19 A20
A29 A30
A39 A40
100
1492-IFM40F-F24-2 1492-RIFM40F-F24-2
Fusible Extra Terminals with 24V AC/DC Blown Fuse LED Indicators for Outputs
Pinout
1 3 5 (odd) 35 37 39 2 4 6 (even) 36 38 40 A1 A11 A12 A21 A22 B38 B39 B40 A31 A32 B18 B19 B20 B21 B22 B23 B1 B2 B3
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. When this IFM is used with a hard contact (relay) output circuit that switches an inductive load, surge suppression must be used (e.g., a 1N4004 diode reverse-wired across a DC load). 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Fusing Fuse holders are included with the IFM. Fuses (5 x 20 mm) are not included. 4. Isolation The power bus, fuse clips, and blown fuse indicators are isolated into four groups of 10 terminals (eight fuse clips and blown fuse indicators). This allows each group of output devices to reference a different power source. 5. Dimensions Refer to page 181.
A2
A9 A10
A19 A20
A29 A30
A39 A40
101
1492-IFM40F-F24D-2
16 Individually fused with 24V DC blown fuse low leakage (0.05 mA) LED circuit, 4 isolated groups, 2 terminals/output
Pinout
6 (even) 36 B18 B3
5 7 9 11 13 15 17
B1 B2
21 23 25 27 29 31 33
B19 B20
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. When this IFM is used with a hard contact (relay) output circuit that switches an inductive load, surge suppression must be used (e.g., a 1N4004 diode reverse-wired across a DC load). 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Fusing Fuse holders are included with the IFM. Fuses (5 x 20 mm) are not included. 4. Isolation Each point is individually fused. The fuse clips and blown fuse indicators are isolated into 4 groups of terminals. This allows use with 4 separate power supplies. 5. Dimensions Refer to page 181.
A1 A2 A3 A4 A5 A6 A7 A8 A9 19 A10 35 A11 A12 A13 A14 A15 A16 A17 A18 A19 A20
COM
+V
102
1492-IFM40F-F24AD-4
Individually Fused w/24V DC blown fuse low leakage (0.05 mA) LED circuit, 4 isolated groups, 4 terminals/inputt
Pinout
A2 B2 5 (even) 6 A8 (odd) B8 B3 A3
A9 B9
A11 B11
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Fusing Fuse holders are included with the IFM. Fuses (5 x 20 mm) are not included. 4. Extra Terminals Two field-side terminals are internally connected on the IFM for each channel, and are available for power source common connections. 5. Isolation Each point is individually fused. The fuse clips and blown fuse indicators are isolated into 4 groups. This allows use of 4 separate power supplies. 6. Dimensions Refer to page 181.
19 20
A17 B17
27 28
A25 B25
35 36
A33 B33
103
1492-IFM40F-F120-2
Fusible Extra Terminals with 120V AC/DC Blown Fuse LED Indicators for Outputs
Pinout
1 3 5 (odd) 35 37 39 2 4 6 (even) 36 38 40 A1 A2 A11 A12 A21 A22 B38 B39 B40 A31 A32 B18 B19 B20 B21 B22 B23 B1 B2 B3
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. When this IFM is used with a hard contact (relay) output circuit that switches an inductive load, surge suppression must be used (e.g., an MOV wired across an AC load). 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Fusing Fuse holders are included with the IFM. Fuses (5 x 20 mm) are not included. 4. Isolation The power bus, fuse clips, and blown fuse indicators are isolated into four groups of 10 terminals (eight fuse clips and blown fuse indicators). This allows each group of output devices to reference a different power source. 5. Dimensions Refer to page 181.
A9 A10
A19 A20
A29 A30
A39 A40
104
1492-IFM40F-FS-2
Fusible 16 Individually Isolated with Extra Terminals for 120V AC/DC Outputs
1492-IFM40F-FS24-2
Fusible 16 Individually Isolated with Extra Terminals and 24V AC/DC Blown Fuse LED Indicators for Outputs
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Fusing Fuse holders are included with the IFM. Fuses (5 x 20 mm) are not included. 4. Isolation The fuse clips are isolated into 16 groups of terminals. This allows each output device to reference a different power source. 5. Dimensions Refer to page 181.
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. When this IFM is used with a hard contact (relay) output circuit that switches an inductive load, surge suppression must be used (e.g., a 1N4004 diode reverse-wired across a DC load). 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Fusing Fuse holders are included with the IFM. Fuses (5 x 20 mm) are not included. 4. Isolation The fuse clips and blown fuse indicators are isolated into 16 groups of terminals. This allows each output device to reference a different power source. 5. Dimensions Refer to page 181.
Pinout
6 (even) 36 B18 B3
Pinout
6 B3 (even) 36 B18
5 (odd) 35
A3
A18
5 (odd) 35
A3
A18
105
1492-IFM40F-FS24-4
Fusible Individually Isolated with 24V AC/DC Blown Fuse Indicators and 4 Terminals/Output
Pinout
5 6 A18 B18
A2 B2
7 8
A19 B19
A3 B3
33
A32 B32
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. When this IFM is used with a hard contact (relay) output circuit that switches an inductive load, surge suppression must be used (e.g., a 1N4004 diode reverse-wired across a DC load or an MOV for AC loads). 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Fusing 20 fuse holders are included with the IFM. Fuses (5 x 20 mm) are not included. 4. Extra Terminals Two field-side terminals are internally connected on the IFM for each channel, and are available for power source common connections. 5. Isolation The fuse clips and blown fuse indicators are isolated into 16 groups of terminals. This allows each output device to reference a different power source. 6. Dimensions Refer to page 181.
34 A16 B16
35 36
A33 B33
A17 B17
106
1492-IFM40F-FS-4
Fusible 16 Individually Isolated 240V AC/DC with 4 Terminals/Output
Pinout
5 6 A18 B18
A2 B2
7 8
A19 B19
A3 B3
33
A32 B32
:Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. When this IFM is used with a hard contact (relay) output circuit that switches an inductive load, surge suppression must be used (e.g., a 1N4004 diode reverse-wired across a DC load or an MOV for AC loads). 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Fusing 20 fuse holders are included with the IFM. Fuses (5 x 20 mm) are not included. 4. Extra Terminals Two field-side terminals are internally connected on the IFM for each channel, and are available for power source common connections. 5. Isolation The fuse clips are isolated into 16 groups of terminals. This allows each output device to reference a different power source. 6. Dimensions Refer to page 181.
34 A16 B16
35 36
A33 B33
A17 B17
107
1492-IFM40F-FS120-2 1492-RIFM40F-FS120-2
Fusible 16 Individually Isolated with Extra Terminals and 120V AC/DC Blown Fuse LED Indicators for Outputs
Pinout
6 (even) 36 B18 B3
5 (odd) 35
A3
A18
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. When this IFM is used with a hard contact (relay) output circuit that switches an inductive load, surge suppression must be used (e.g., a 1N4004 diode reverse-wired across a DC load or an MOV across an AC load). 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Fusing Fuse holders are included with the IFM. Fuses (5 x 20 mm) are not included. 4. Isolation The fuse clips and blown fuse indicators are isolated into 16 groups of terminals. This allows each output device to reference a different power source. 5. Dimensions Refer to page 181.
108
1492-IFM40F-FS120-4 1492-IFM40F-FS120-4
Fusible 16 Individually Isolated with 120V AC/DC Blown Fuse LED Indicators & 4 Terminals/Output
Pinout
5 6 A3 B3 7 8 A5 B5 (even) A4 B4 A2 B2
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. When this IFM is used with a hard contact (relay) output circuit that switches an inductive load, surge suppression must be used (e.g., a 1N4004 diode reverse-wired across a DC load or an MOV across an AC load). 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Fusing Fuse holders are included with the IFM. Fuses (5 x 20 mm) are not included. 4. Extra Terminals Two field-side terminals are internally connected on the IFM for each channel, and are available for power source common connections. 5. Isolation The fuse clips and blown fuse indicators are isolated into 16 groups of terminals. This allows each output device to reference a different power source. 6. Dimensions Refer to page 181.
109
1492-IFM40F-FS240-4
Fusible 16 Individually Isolated with 240V AC/DC Blown Fuse LED Indicators & 4 Terminals/Output
Pinout
5 6 A18 B18
A2 B2
7 8
A19 B19
A3 B3
33 34
A32 B32
A16 B16
35
A33 B33
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. When this IFM is used with a hard contact (relay) output circuit that switches an inductive load, surge suppression must be used (e.g., a 1N4004 diode reverse-wired across a DC load or an MOV across an AC load). 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Fusing Fuse holders are included with the IFM. Fuses (5 x 20 mm) are not included. 4. Extra Terminals Two field-side terminals are internally connected on the IFM for each channel, and are available for power source common connections. 5. Isolation The fuse clips and blown fuse indicators are isolated into 16 groups of terminals. This allows each output device to reference a different power source. 6. Dimensions Refer to page 181.
36
A17 B17
110
1492-IFM40F-FS24A-4
Fusible 16 Individually Isolated 24V AC/DC with 4 Terminals/Input
Pinout
A2 B2 5 6 A4 B4 7 8 (even) (odd) A30 B30 33 34 A32 B32 35 36 A33 B33 A31 B31 A5 B5 A3 B3
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Fusing Fuse holders are included with the IFM. Fuses (5 x 20 mm) are not included. 4. Extra Terminals Two field-side terminals are internally connected on the IFM for each channel, and are available for power source common connections. 5. Isolation The fuse clips and blown fuse indicators are isolated into 16 groups of terminals. This allows each input device to reference a different power source. 6. Dimensions Refer to page 181.
111
1492-IFM40F-FSA-4
Fusible 16 Individually Isolated 120V AC/DC 4 Terminals/Input
1492-IFM40F-FS120A-4 1492-RIFM40F-FS120A-4
Fusible 16 Individually Isolated with 120V AC/DC Blown Fuse LED Indicators & 4 Terminals/Input
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Fusing Fuse holders are included with the IFM. Fuses (5 x 20 mm) are not included. 4. Extra Terminals Two field-side terminals are internally connected on the IFM for each channel, and are available for power source common connections. 5. Isolation The fuse clips are isolated into 16 groups of terminals. This allows each input device to reference a different power source. 6. Dimensions Refer to page 181.
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Fusing Fuse holders are included with the IFM. Fuses (5 x 20 mm) are not included. 4. Extra Terminals Two field-side terminals are internally connected on the IFM for each channel, and are available for power source common connections. 5. Isolation The fuse clips and blown fuse indicators are isolated into 16 groups of terminals. This allows each input device to reference a different power source. 6. Dimensions Refer to page 181.
Pinout
A2 B2 5 6 A4 B4 7 8 (even) (odd) A30 B30 33 34 A32 B32 35 36 A33 B33 A31 B31 A5 B5 A3 B3
Pinout
A2 B2 5 6 A4 B4 7 8 (even) (odd) A30 B30 33 34 A32 B32 35 36 A33 B33 A31 B31 A5 B5 A3 B3
112
1492-IFM40F-FS240A-4
Fusible 16 Individually Isolated with 240V AC/DC Blown Fuse LED Indicators and 4 Terminals/Input
Pinout
A2 B2 5 6 A4 B4 7 8 (even) (odd) A30 B30 33 34 A32 B32 35 36 A33 B33 A31 B31 A5 B5 A3 B3
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the IFM. 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Fusing Fuse holders are included with the IFM. Fuses (5 x 20 mm) are not included. 4. Extra Terminals Two field-side terminals are internally connected on the IFM for each channel, and are available for power source common connections. 5. Isolation The fuse clips and blown fuse indicators are isolated into 16 groups of terminals. This allows each input device to reference a different power source. Dimensions Refer to page 181.
113
1492-XIM2024-8R
Relay Master (LED Indicating) 20-Pin Master with Eight (8) 24V DC Relays
Pinout
CN
~ ~
K0
TB
A3
A4 A5 A6
~ ~
4 K1
A7 A8 B3
~ ~
5 K2
B4 B5 B6
~ ~
6 K3
B7 B8 B9
~ ~
7 K4
~ ~
8 K5
B13 B14 A9
~ ~
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the XIM. 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Dimensions Refer to page 181. 4. Maximum Relay Switching Refer to page 186. 5. LEDs provide PLC output ON/OFF indication. 6. With expansion module and cable (included with expansion module) can expand to 16 relays.
K6
~ ~
10 K7
A13 A14
20
B16 7 CJ OUT 8
19 1
B15 B1
B2 1 CJOUT 2
CN
11 12 13 14 15 16 17 18
CJOUT
20 24 28 30 32 31 34 33
114
1492-XIM20120-8R
Relays Masters (LED Indicating) 20-Pin Master with Eight (8) 120V AC Relays
Pinout
CN
~ ~
K0
TB
A3
A4 A5 A6
~ ~
4 K1
A7 A8 B3
~ ~
5 K2
B4 B5 B6
~ ~
6 K3
B7 B8 B9
~ ~
7 K4
~ ~
8 K5
B13 B14 A9
~ ~
9 K6
Application Notes
10
~ ~
K7
A13 A14
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the XIM. 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Dimensions Refer to page 181. 4. Maximum Relay Switching Refer to page 186. 5. LEDs provide PLC output ON/OFF indication. 6. With expansion module and cable (included with expansion module) can expand to 16 relays.
20
B16 7 CJ OUT 8
19 1
B15 B1
B2 1 CJOUT 2
CN
11 12 13 14 15 16 17 18
CJOUT
20 24 28 30 32 31 34 33
115
1492-XIM2024-16R
Relays Master (LED Indicating) 20-Pin Master with Sixteen (16) 24V DC Relays
Pinout
1492-XIM2024-16R TB 1
K 16
C N
3
~ ~
4
K 17
~ ~
5
K 18
~ ~
6
K 19
~ ~
7
K 20
~ ~
8
K 21
~ ~
9
K 22
~ ~
10
K 23
3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26
~ ~
11
K 24
TB 2
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
TB 2
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the XIM. 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Dimensions Refer to page 181. 4. Maximum Relay Switching Refer to page 186. 5. LEDs provide PLC output ON/OFF indication. 6. No expansion capability.
~ ~
12
K 25
~ ~
13
K 26
~ ~
14
K 27
~ ~
15
K 28
~ ~
16
K 29
~ ~
17
K 30
~ ~
18
K 31
26 20 19 25
TB 1
1 2
1 2
116
1492-XIM2024-16RF
Relay Master (LED Indicating) 20-Pin Master with Sixteen (16) 24V DC Relays with Fusing
Pinout
1492-XIM2024-16RF
CN
~ ~
K0
TB1
3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
TB2
~ ~
4
K1
~ ~
5
K2
~ ~
6
K3
~ ~
7
K4
~ ~
8
K5
~ ~
9
K6
~ ~
K7
10
~ ~
11
K0
TB2
~ ~
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the XIM. 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Dimensions Refer to 181. 4. Maximum Relay Switching Refer to page 186. 5. LEDs provide PLC output ON/OFF indication. 6. No expansion capability.
12
K1
~ ~
13
K2
~ ~
14
K3
~ ~
15
K4
~ ~
16
K5
~ ~
17
K6
~ ~
18
K7
26 20 19 1 2 25
TB1
1 2
117
1492-XIM20120-16R
Relay Master (LED Indicating) 20-Pin Master with Sixteen (16) 120V AC Relays
Pinout
1492-XIM2024-16R TB 1
K 16
C N
3
~ ~
4
K 17
~ ~
5
K 18
~ ~
6
K 19
~ ~
7
K 20
~ ~
8
K 21
~ ~
9
K 22
~ ~
10
K 23
3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26
~ ~
11
K 24
TB 2
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
TB 2
~ ~
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the XIM. 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Dimensions Refer to page 181. 4. Maximum Relay Switching Refer to page 186. 5. LEDs provide PLC output ON/OFF indication. 6. No expansion capability.
12
K 25
~ ~
13
K 26
~ ~
14
K 27
~ ~
15
K 28
~ ~
16
K 29
~ ~
17
K 30
~ ~
18
K 31
26 20 19 25
TB 1
1 2
1 2
118
1492-XIM20120-16RF
Relay Master (LED Indicating) 20-Pin Master with Sixteen (16) 120V AC Relays with Fusing
Pinout
1492-XIM20120-16RF
CN
~ ~
K0
TB1
3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
TB2
~ ~
4
K1
~ ~
5
K2
~ ~
6
K3
~ ~
7
K4
~ ~
8
K5
~ ~
9
K6
~ ~
K7
10
~ ~
11
K0
TB2
~ ~
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the XIM. 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Dimensions Refer to page 181. 4. Maximum Relay Switching Refer to page 186. 5. LEDs provide PLC output ON/OFF indication. 6. No expansion capability.
12
K1
~ ~
13
K2
~ ~
14
K3
~ ~
15
K4
~ ~
16
K5
~ ~
17
K6
~ ~
18
K7
26 20 19 1 2 25
TB1
1 2
119
1492-XIM4024-8R
Relay Master (LED Indicating) 40-Pin Master with Eight (8) 24V DC Relays
Pinout
CN
~ ~
K0
TB
A3
A4 A5 A6
~ ~
4 K1
A7 A8 B3
~ ~
5 K2
B4 B5 B6
~ ~
6 K3
B7 B8 B9
~ ~
7 K4
~ ~
8 K5
B13 B14 A9
~ ~
9 K6
~ ~
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the XIM. 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Dimensions Refer to page 181. 4. Maximum Relay Switching Refer to page 186. 5. LEDs provide PLC output ON/OFF indication. 6. With expansion module(s) and cable (included with expansion module) can expand to 32 relays.
10
K7
A13 A14
20
B16 7 CJ OUT 8
19 1
B15 B1
B2 1 CJOUT 2
120
1492-XIM4024-8R, Continued
Pinout, Continued
CN
~ ~
K0
TB
A3
CN
21 23 25 27 29
CJOUT
20 24 28 30 32 31 34 33
A4 A5 A6
~ ~
7 K1
A7 A8 B3
~ ~
9 K2
B4 B5 B6
31 33 35
~ ~
11 K3
B7 B8
~ ~
13 K4
12 11 14 13 16 15 18 17
~ ~
15
~ ~
17
~ ~
19 K7
A13 A14
CJOUT
7 8 5 9 10 3 4 6 1
22 24 26 28 30 32 34 36
22 26 19 21 23 25 27 29
37 39 38 40 2 4 1 3
121
1492-XIM4024-16R 1492-RXIM4024-16R
Relay Master (LED Indicating) 40-Pin Master with Sixteen (16) 24V DC Relays
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the XIM. 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Dimensions Refer to page 181. 4. Maximum Relay Switching Refer to page 186. 5. LEDs provide PLC output ON/OFF indication. 6. With expansion module(s) and cable(s) (included with expansion module) can expand to 32 relays.
Pinout
Refer to page 122.
122
~ ~
K0
TB1
A3
CN
~ ~
K8
TB2
A3
A4 A5 A6
21
A4 A5 A6
~ ~
7 K1
~ ~
23 K9
A7 A8 B3
A7 A8 B3
~ ~
9 K2
~ ~
25 K10
B4 B5 B6
B4 B5 B6
~ ~
11 K3
~ ~
27 K11
B7 B8 B9
B7 B8 B9
~ ~
13 K4
~ ~
29 K12
~ ~
15 K5
~ ~
K13
B13 B14 A9
B13 B14 A9
33
~ ~
17 K6
~ ~
K14
~ ~
K15
~ ~
19 K7
A13 A14
A13 A14
37 39 38 40
TB2
B1 B2 A1 A2
CJOUT
7 8 5 9 10
TB1
2 4 1 3 A1 A2 B1 B2
3 4 6 1 2
CN
6 8 10 12 14 16 18 20
CJOUT
20 24 28 30 32 31 34 33
22 24 26 28 30 32 34 36
12 11 14 13 16 15 18 17
123
1492-XIM4024-16RF
Relay Master (LED Indicating) 40-Pin Master with Sixteen (16) 24V DC Relays with Fusing
Pinout
CN
~ ~
K0
TB1
3 4 5 6
K1
~ ~
7
7 8 9 10 11 12
~ ~
9
K2
~ ~
11
K3
13 14 15
~ ~
13
K4
16 17 18
~ ~
15
K5
19 20 21
~ ~
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the XIM. 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Dimensions Refer to page 181. 4. Maximum Relay Switching Refer to page 186. 5. LEDs provide PLC output ON/OFF indication. 6. With expansion module(s) and cable(s) (included with expansion module) can expand to 32 relays.
17
K6
22 23 24
~ ~
K7
19
25 26
~ ~
21
CN CJOUT
TB2
1
K8
2 3 4
~ ~
23
K9
6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36
20 24 28 30 32 31 34 33
5 6 7 8 9 10
~ ~
25
K10
~ ~
27
K11
11 12 13 14 15 16
~ ~
29
K12
12 11 14 13 16 15 18 17
~ ~
31
K13
17 18 19 20 21 22
~ ~
33
K14
~ ~
K15
35
23 24
TB2 CJOUT
37 39 38 40 2 4 1 3
25 26
TB1
7 8 5 9 10 3 4 6 1 2
124
1492-XIM24-8R 1492-RXIM24-8R
Relay Expander (LED Indicating) with Eight (8) 24V DC Relays
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the XIM. 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. This relay expander must be used with a 24V DC relay master. 4. Dimensions Refer to page 181. 5. Maximum Relay Switching Refer to page 186. 6. LEDs provide PLC output ON/OFF indication.
Pinout
Refer to page 125.
125
~ ~
K0
TB
A1 A2 A3 A4 K1 A5 A6 B1 K2 B2 B3 B4 25 26 29 24 23 22 21 20 19 18 A7 K6 A8 A9 A10 17 15 14 13 11 10 9 7 5 31 32 30
CJIN
CJOUT
1 2 3 4 6 5 7 8 9 10 20 24 28 30 32 31 34 33 14 12 13 16 11 15 18 17
~ ~
12
~ ~
8
~ ~
6 K3
B5 B6 B7
~ ~
4 K4
B8 B9 B10
~ ~
3 K5
B11 B12
~ ~
2
~ ~
1 K7
A11 A12
27 28
126
1492-XIM120-8R
Relay Expander (LED Indicating) with Eight (8) 120V AC Relays
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the XIM. 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. This relay expander must be used with a 120V AC relay master. 4. Dimensions Refer to page 181. 5. Maximum Relay Switching Refer to page 186. 6. LEDs provide PLC output ON/OFF indication.
Pinout
Refer to page 127.
127
1492-XIM120-8R, Continued
Pinout, Continued
CJIN
16
~ ~
K0
TB
A1 A2 A3 A4 K1 A5 A6 B1 K2 B2 B3 B4 29 24 23 22 21 20 19 18 17 15 A10 K7 A11 A12 13 14 25 26 31 32 30
CJIN
CJOUT
1 2 3 4 6 5 7 8 9 10 20 24 28 30 32 31 34 33 14 12 13 16 11 15 18 17
~ ~
12
~ ~
8
~ ~
6 K3
B5 B6 B7
~ ~
4 K4
B8 B9 B10
~ ~
3 K5
B11 B12 A7
~ ~
2 K6
A8 A9
~ ~
1
27 28
11 10 9 7 5
128
1492-XIM24-16RF
Expander with Sixteen (16) 24V DC Relays with Fusing
Pinout
1492-XIM24-16RF
CJIN
16
~ ~
K16
TB1
1 2 3 4
~ ~
12
K17
5 6 7 8 9 10 11 12 13 14 15 16
~ ~
8
K18
~ ~
6
K19
~ ~
4
K20
~ ~
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the XIM. 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. This relay expander must be used with a 24 VDC relay master. 4. Dimensions Refer to page 181. 5. Maximum Relay Switching Refer to page 186. 6. LEDs provide PLC output ON/OFF indication.
K21
17 18 19
~ ~
2
K22
20 21 22
~ ~
K23
23 24
TB2
~ ~
24
K24
1 2 3 4
~ ~
23
K25
5 6 7 8 9 10 11 12 13 14 15 16
~ ~
22
K26
~ ~
21
K27
~ ~
20
K28
~ ~
19
K29
17 18 19
~ ~
18
K30
20 21 22
~ ~
K31
17
CJIN
23 24
27 28
129
1492-XIMF-F24-2
Fusible 8-Channel Expander with 24V DC Blown Fuse Indicators
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the XIM. 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Extra Terminals Eight field-side terminals are jumpered together on the XIM. For some I/O modules, the terminals are also internally connected to module common through the prewired cable. Refer to the XIM and CABLE pinouts. 4. Dimensions Refer to page 181. 5. LEDs provide blown fuse indication.
Pinout
Refer to page 130.
130
1492-XIMF-F24-2, Continued
Pinout, Continued
CJIN F8
16 B1 31 32
TB
30
CJIN
CJOUT
1 2 3 4 6
F9
12 B2 25 8
5 7 8 9 10
F10
B3 26 29
F11
B4 24 23 20 24 28 30 32 31 34 33
F12
B5
22 21
F13
B6 20 19
F14
B7
18 17
F15
B8 15 14 A1 A2 13 11 10 9 7 5 13 16 11 15 18 17 14 12
27 28
A3 A4 A5 A6 A7 A8
131
1492-XIMF-F120-2
Fusible 8-Channel Expander with 120V AC Blown Fuse Indicators
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the XIM. 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Extra Terminals Eight field-side terminals are jumpered together on the XIM. For some I/O modules, the terminals are also internally connected to module common through the prewired cable. Refer to the XIM and CABLE pinouts. 4. Dimensions Refer to page 181. 5. LEDs provide blown fuse indication.
Pinout
Refer to page 132.
132
1492-XIMF-F120-2, Continued
Pinout, Continued
CJIN F8
16 B1 31 32 B2 5 7 8 9 29 6 10
TB
30
CJIN
CJOUT
1 2 3 4 6
F9
12
25 8
F10
B3 26
F11
B4 24 20 24 28 30 32 31 34 33
F12
23 B5 22 21
F13
B6 20 19
F14
B7
18 17
F15
B8 15 14 13 11 10 9 7 5 14 12 13 16 11 15 18 17
A1 A2 27 28 A3 A4 A5 A6 A7 A8
133
1492-XIMF-2
Expander with Eight (8) Feed-Through Channels
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the XIM. 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Extra Terminals Eight field-side terminals are jumpered together on the XIM. For some I/O modules, the terminals are also internally connected to module common through the prewired cable. Refer to the XIM and CABLE pinouts. 4. Dimensions Refer to page 181.
Pinout
Refer to page 134.
134
1492-XIMF-2, Continued
Pinout, Continued
CJIN
16
TB
30 B1 31 32
CJIN
CJOUT
1 2 3 4 6
12
B2 25 5 7 8 9 29 10
B3
26
B4 24 23 20 24 28 30 32 31 34 33
B5 22 21
B6
20 19
B7
18 17
B8 15 14 A1 A2 13 11 10 9 7 5 13 16 11 15 18 17 14 12
27 28
A3 A4 A5 A6 A7 A8
135
Bulletin 1492 pre-wired cables are designed to minimize control wiring in a panel. Digital pre-wired cables, when used with an IFM or XIM, replace the point-to-point wiring between Allen-Bradley programmable controller I/O modules and individual terminal blocks. The digital ready-to-wire cables provide one end of the cable pre-terminated, for either an IFM (IFM-ready cable) or a programmable controller I/O module (I/O module-ready cable).
Pre-Wired Cables
Specifications
The pre-wired cables have a Bulletin 1746 Removable Terminal Block, 1756 Removable Terminal Block, 1769 Removable Terminal Block, or 1771 Wiring Arm on one end and a cable connector on the other to connect to the IFM or XIM. The broad offering of digital pre-wired cables supports over 100 different 16- and 32-point Bulletin 1746, 1756, 1769, and 1771 digital I/O modules.
136
No. of Conductors 20 20 20 20 20 20 20 20 20 40 40 40 40 40 20 40 40 20 20 20 20 20 20 40 40 40 40 20 20 20 20 20 20 20 20 20 20 20
Conductor Size #22 AWG #22 AWG #22 AWG #22 AWG #22 AWG #22 AWG #22 AWG #22 AWG #22 AWG #22 AWG #22 AWG #22 AWG #22 AWG #22 AWG #22 AWG #22 AWG #22 AWG #22 AWG #22 AWG #22 AWG #22 AWG #22 AWG #22 AWG #22 AWG #22 AWG #22 AWG #22 AWG #22 AWG #22 AWG #22 AWG #22 AWG #22 AWG #22 AWG #22 AWG #22 AWG #22 AWG #22 AWG #22 AWG
Nominal Outer Diameter 9.0 mm (0.36 in.) 9.0 mm (0.36 in.) 9.0 mm (0.36 in.) 9.0 mm (0.36 in.) 9.0 mm (0.36 in.) 9.0 mm (0.36 in.) 9.0 mm (0.36 in.) 9.0 mm (0.36 in.) 9.0 mm (0.36 in.) 11.7 mm (0.46 in.) 11.7 mm (0.46 in.) 11.7 mm (0.46 in.) 11.7 mm (0.46 in.) 11.7 mm (0.46 in.) 9.0 mm (0.36 in.) 11.7 mm (0.46 in.) 11.7 mm (0.46 in.) 9.0 mm (0.36 in.) 11.7 mm (0.46 in.) 9.0 mm (0.36 in.) 9.0 mm (0.36 in.) 9.0 mm (0.36 in.) 9.0 mm (0.36 in.) 11.7 mm (0.46 in.) 11.7 mm (0.46 in.) 11.7 mm (0.46 in.) 11.7 mm (0.46 in.) 9.0 mm (0.36 in.) 9.0 mm (0.36 in.) 9.0 mm (0.36 in.) 9.0 mm (0.36 in.) 9.0 mm (0.36 in.) 9.0 mm (0.36 in.) 9.0 mm (0.36 in.) 9.0 mm (0.36 in.) 9.0 mm (0.36 in.) 9.0 mm (0.36 in.) 9.0 mm (0.36 in.)
I/O Module Connector 1746-RT25R Red Removable Terminal Block 1746-RT25B Blue Removable Terminal Block 1746-RT25R Red Removable Terminal Block 1746-RT25R Red Removable Terminal Block 1746-RT25C Orange Removable Terminal Block 1746-RT25B Blue Removable Terminal Block 1771-WH (16-Point/21 Terminal) Wiring Arm 1771-WHF (16-Point/21 Terminal) Fused Wiring Arm 1746-RT25R Red Removable Terminal Block 1746-N3 40-Pin Cable Connector 1771-WN (32-Point/40 Terminal) Wiring Arm 1771-WN (32-Point/40 Terminal) Wiring Arm 1771-WN (32-Point/40 Terminal) Wiring Arm 1771-WN (32-Point/40 Terminal) Wiring Arm 1746-RT25C Orange Removable Terminal Block 1771-WN (32-Point/40 Terminal) Wiring Arm 1771-WN (32-Point/40 Terminal) Wiring Arm 1746-RT25C Orange Removable Terminal Block 1771-WA (8-Point/10 Terminal) Wiring Arm 1756-TBNH Removable Terminal Block 1756-TBNH Removable Terminal Block 1756-TBNH Removable Terminal Block 1756-TBNH Removable Terminal Block 1756-TBCH Removable Terminal Block 1756-TBCH Removable Terminal Block 1762-L40xxx Output Terminal 1762-L40xxx Input Terminal 1764-24AWA, -24BWA Input Terminal 1764-28BXB Input Terminal 1764-24AWA, -24BWA Output Terminal 1764-28BXB Output Terminal 1769-RTBN18 Removable Terminal Block 1769-RTBN18 Removable Terminal Block 1769-RTBN10 Removable Terminal Block 1769-RTBN18 Removable Terminal Block 1769-RTBN18 Removable Terminal Block 1769-RTBN18 Removable Terminal Block 1769-RTBN18 Removable Terminal Block
137
Cables are available in standard lengths of 0.5 m, 1.0 m, 2.5 m, and 5.0 m. To order, insert the code for the desired cable length into the catalog number (005 = 0.5 m, 010 = 1.0 m, 025 = 2.5 m, and 050 = 5.0 m). Example: Catalog Number 1492-CABLE005A is for a 0.5 m cable for the 1746-IA16 I/O Module. Also refer to Build-to-Order Length Cables on page 64.
138
Pinouts
19
39 1
20 2
40
20-Conductor Cable
40-Conductor Cable
139
Pinouts, Continued
Digital/Analog Programmable Controller Wiring Systems
Red RTB Green (4) Blue (6) Red/Black (8) Orange/Black (10) Black/White (12) Green/White (14) Black/Red (16) Orange/Red (18) Red/Green (20)
Red (3) Orange (5) White/Black (7) Green/Black (9) Blue/Black (11) Red/White (13) Blue/White (15) White/Red (17) Blue/Red (19)
1 3 5 7 9 11 13 15 17
2 4 6 8 10 12 14 16 18
Blue RTB Green (4) Blue (6) Red/Black (8) Orange/Black (10) Black/White (12) Green/White (14) Black/Red (16) Orange/Red (18) Red/Green (20)
1492-CABLEA
1492-CABLEB
White (2) Black (1) Green (4) Blue (6) Red/Black (8) Orange/Black (10) Black/White (12) Green/White (14) Black/Red (16) Orange/Red (18)
1 3 5 7 9 11 13 15 17
2 4 6 8 10 12 14 16 18
Red RTB White (2) Black (1) Red (3) Green (4) Orange (5) Blue (6) White/Black (7) Red/Black (8) Green/Black (9) Blue/Red (19) Orange/Black (10) Red/Green (20) Black/White (12) Blue/Black (11) Green/White (14) Red/White (13) Black/Red (16) Blue/White (15) Orange/Red (18) White/Red (17)
1 3 5 7 9 11 13 15 17
2 4 6 8 10 12 14 16 18
White (2) Orange RTB Black (1) Red (3) Green (4) Orange (5) Blue (6) White/Black (7) Red/Black (8) Green/Black (9) Blue/Red (19) Orange/Black (10) Red/Green (20) Black/White (12) Blue/Black (11) Green/White (14) Red/White (13) Black/Red (16) Blue/White (15) Orange/Red (18) White/Red (17)
Blue RTB
1 3 5 7 9 11 13 15 17 2 4 6 8 10 12 14 16 18
1492-CABLEC
1492-CABLED
1492-CABLEE
A B C D 00 01 02 03 04 05 06 07 10 11 12 13 14
15 16 17 E
Black (1) White (2) Blue/Red (19) Red (3) Green (4) Orange (5) Blue (6) White/Black (7) Red/Black (8) Green/Black (9) Orange/Black (10) Blue/Black (11) Black/White (12) Red/White (13) Green/White (14) Blue/White (15) Black/Red (16) White/Red (17) Orange/Red (18) Red/Green (20)
CAUTION
DISCONNECT POWER BEFORE SERVICING FUSES ALL FUSES 30-250V
A B C D 00 01 02 03 04 05 06 07 10 11 12 13 14
15 16 17 E
Black (1) White (2) Blue/Red (19) Red (3) Green (4) Orange (5) Blue (6) White/Black (7) White (2) Red/Black (8) Black (1) Green/Black (9) Green (4) Orange/Black (10) Blue (6) Blue/Black (11) Red/Black (8) Black/White (12) Red/White (13) Orange/Black (10) Green/White (14) Black/White (12) Blue/White (15) Green/White (14) Black/Red (16) Black/Red (16) White/Red (17) Orange/Red (18) Orange/Red (18) Red/Green (20)
Red (3) Orange (5) White/Black (7) Green/Black (9) Blue/Red (19) Blue/Black (11) Red/White (13) Blue/White (15) White/Red (17)
1492-CABLEF
1492-CABLEFF
Refer to footnote on page 145.
1492-CABLEG
140
Pinouts, Continued
Orange (5) Green/Black (9) Red/White (13) White/Red (17) Black (1) Orange/Green (21) Green/Black-White (25) White/Red-Green (29) Blue/White-Orange (33) White/Red-Blue (37) Blue (6) Orange/Black (10) Green/White (14) Orange/Red (18) White (2) Black/White-Red (22) Orange/Black-White (26) Red/Black-Green (30) Black/White-Orange (34) Black/White-Green (38)
Red (3) White/Black (7) Blue/Black (11) Blue/White (15) Blue/Red (19) White/Black-Green (39) White/Black-Red (23) Blue/Black-White (27) Green/Black-Orange (31) White/Red-Orange (35) Green (4) Red/Black (8) Black/White (12) Black/Red (16) Red/Green (20) Red/White-Green (40) Red/Black-White (24) Black/Red-Green (28) Orange/Black-Green (32) Orange/White-Blue (36)
2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40
1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39
Black (1) Orange (5) Green/Black (9) Red/White (13) White/Red (17) White/Red-Blue (37) Orange/Green (21) Green/Black-White (25) White/Red-Green (29) Blue/White-Orange (33) White (2) Blue (6) Orange/Black (10) Green/White (14) Orange/Red (18) Black/White-Green (38) Black/White-Red (22) Orange/Black-White (26) Red/Black-Green (30) Black/White-Orange (34)
1492-CABLEJ
Orange (5) Green/Black (9) Red/White (13) White/Red (17) White/Red-Blue (37) Orange/Green (21) Green/Black-White (25) White/Red-Green (29) Blue/White-Orange (33) Black (1) White/Black-Green (39) White (2) Red (3) Blue (6) Green (4) Orange/Black (10) Orange (5) Green/White (14) Blue (6) Orange/Red (18) White/Black (7) Black/White-Green (38) Red/Black (8) Black/White-Red (22) Green/Black (9) Orange/Black (10) Orange/Black-White (26) Red/Black-Green (30) Blue/Black (11) Black/White-Orange (34) Black/White (12) Red/White (13) Red/White-Green (40)
Green/White (14) Blue/White (15) Black/Red (16) White/Red (17) Orange/Red (18) Blue/Red (19) Red/Green (20) Orange/Green (21) Black/White-Red (22) White/Black-Red (23) Red/Black-White (24) Green/Black-White (25) Orange/Black-White (26) Blue/Black-White (27) Black/Red-Green (28) White/Red-Green (29) Red/Black-Green (30) Green/Black-Orange (31) Orange/Black-Green (32) Blue/White-Orange (33) Black/White-Orange (34) White/Red-Orange (35) Orange/White-Blue (36) White/Red-Blue (37) Black/White-Green (38) White/Black-Green (39) Red/White-Green (40)
2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39
1492-CABLEK
Black (1) White/Black (7) Blue/Black (11) Blue/White (15) Blue/Red (19) Red (3) White/Black-Red (23) Blue/Black-White (27) Green/Black-Orange (31) White/Red-Orange (35) White (2) Red/Black (8) Black/White (12) Black/Red (16) Red/Green (20) Green (4) Red/Black-White (24) Black/Red-Green (28) Orange/Black-Green (32) Orange/White-Blue (36)
1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39
1492-CABLEL
39 40
1492-CABLEH
Orange (5) White/Black (7) Green/Black (9) Blue/Black (11) NC Red/White (13) Blue/White (15) White/Red (17) Blue/Red (19) NC Orange/Green (21) White/Black-Red (23) Green/Black-White (25) Blue/Black-White (27) NC White/Red-Green (29) Green/Black-Orange (31) Blue/White-Orange (33) White/Red-Orange (35) NC
2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40
Blue (6) Red/Black (8) Orange/Black (10) Black/White (12) NC Green/White (14) Black/Red (16) Orange/Red (18) Red/Green (20) NC Black/White-Red (22) Red/Black-White (24) Orange/Black-White (26) Black/Red-Green (28) NC Red/Black-Green (30) Orange/Black-Green (32) Black/White-Orange (34) Orange/White-Blue (36) NC
1492-CABLEM
Refer to footnote on page 145. Connector Pin reference. For the IFM end reference, refer to the table on page 147 and match the wire color to the IFM Pin reference number.
141
Pinouts, Continued
Black (1) White (2) Green (4) Blue (6) Red/Black (8) Orange/Black (10) Black/White (12) Green/White (14) Black/Red (16) Orange/Red (18)
2 4 6 8 10 12 14 16 18
Red (3) Orange (5) White/Black (7) Green/Black (9) Blue/Red (19) Blue/Black (11) Red/White (13) Blue/White (15) White/Red (17)
0 1 2 3 4 5 6 7 B
White (2) Blue/Red (19) Red (3) Green (4) Orange (5) Blue (6) Blue/White (15) Black/Red (16) White/Red (17) Orange/Red (18) White/Black (7) Blue/Black (11)
Black (1) White/Black (7) Red/Black (8) Green/Black (9) Orange/Black (10) Blue/Black (11) Black/White (12) Red/White (13) Green/White (14) Red/Green (20)
2 4 6 8
1 3 5 7
10 9 12 11 14 13 16 15 18 17 20 19
White (2) Red (3) Green (4) Orange (5) Blue (6) Blue/White (15) Black/Red (16) White/Red (17) Orange/Red (18) Blue/Red (19)
1492-CABLEN
1492-CABLET
1492-CABLEU
Red (3) White/Black (7) Blue/Black (11) Blue/White (15) Blue/Red (19) White/Black-Red (23) Blue/Black-White (27) Green/Black-Orange (31) White/Red-Orange (35) White/Black-Green (39) Green (4) Red/Black (8) Black/White (12) Black/Red (16) Red/Green (20) Red/Black-White (24) Black/Red-Green (28) Orange/Black-Green (32) Orange/White-Blue (36) Red/White-Green (40)
2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40
1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39
Black (1) Orange (5) Green/Black (9) Red/White (13) White/Red (17) Orange/Green (21) Green/Black-White (25) White/Red-Green (29) Blue/White-Orange (33) White/Red-Blue (37) White (2) Blue (6) Orange/Black (10) Green/White (14) Orange/Red (18) Black/White-Red (22) Orange/Black-White (26) Red/Black-Green (30) Black/White-Orange (34) Black/White-Green (38)
NC White (2) Green (4) Blue (6) Red/Black (8) Black/White (12) Green/White (14) Black/Red (16) Orange/Red (18) NC
2 4 6 8
1 3 5 7
Black (1) Red (3) Orange (5) White/Black (7) Green/Black (9) Blue/Black (11) Red/White (13) Blue/White (15) White/Red (17) Blue/Red (19)
10 9 12 11 14 13 16 15 18 17 20 19
1492-CABLER
1492-CABLEV
White (2) Green (4) Blue (6) Red/Black (8) NC Black/White (12) Green/White (14) Black/Red (16) Orange/Red (18)
1 3 5 7 9 11 13 15 17
Orange RTB
2 4 6 8 10 12 14 16 18
Red (3) Orange (5) White/Black (7) Green/Black (9) NC Blue/Black (11) Red/White (13) Blue/White (15) White/Red (17)
White (2) Green (4) Blue (6) Red/Black (8) Orange/Black (10) Black/White (12) Green/White (14) Black/Red (16) Orange/Red (18) Red/Green (20)
2 4 6 8
1 3 5 7
10 9 12 11 14 13 16 15 18 17 20 19
Red (3) Orange (5) White/Black (7) Green/Black (9) Black (1) Blue/Black (11) Red/White (13) Blue/White (15) White/Red (17) Blue/Red (19)
1492-CABLES
Refer to footnote on page 145.
1492-CABLEW
142
Pinouts, Continued
Green (4) Blue (6) Red/Black (8) Orange/Black (10) Black (1) Black/White (12) Green/White (14) Black/Red (16) Orange/Red (18) Blue/Red (19)
2 4 6 8
1 3 5 7
Red (3) Orange (5) White/Black (7) Green/Black (9) White (2) Blue/Black (11) Red/White (13) Blue/White (15) White/Red (17) Red/Green (20)
10 9 12 11 14 13 16 15 18 17 20 19
Orange (5) White/Black (7) Green/Black (9) Blue/Black (11) Red/White (13) Blue/White (15) White/Red (17) Blue/Red (19) Orange/Green (21) White/Black-Red (23) Green/Black-White (25) Blue/Black-White (27) White/Red-Green (29) Green/Black-Orange (31) Blue/White-Orange (33) White/Red-Orange (35) NC NC
2 4 6 8
1 3 5 7
10 9 12 11 14 13 16 15 18 17 20 19 22 21 24 23 26 25 28 27 30 29 32 31 34 33 36 35
Blue (6) Red/Black (8) Orange/Black (10) Black/White (12) Green/White (14) Black/Red (16) Orange/Red (18) Red/Green (20) Black/White-Red (22) Red/Black-White (24) Orange/Black-White (26) Black/Red-Green (28) Red/Black-Green (30) Orange/Black-Green (32) Black/White-Orange (34) Orange/White-Blue (36) NC NC
1492-CABLEX
White/Black (7) Blue/Black (11) Blue/White (15) Blue/Red (19) White/Black-Red (23) Blue/Black-White (27) Green/Black-Orange (31) Black (1) White/Red-Orange(35)
1492-CABLEY
Orange (5) Green/Black (9) Red/White (13) White/Red (17) Orange/Green (21) Green/Black-White (25) White/Red-Green (29) Blue/White-Orange (33) White/Black-Green (39) White/Red-Blue (37) Blue (6) Orange/Black (10) Green/White (14) Orange/Red (18) Black/White-Red (22) Orange/Black-White (26) Red/Black-Green (30) Black/White-Orange (34) Red/White-Green (40) Black/White/Green (38)
2 4 6 8
1 3 5 7
10 9 12 11 14 13 16 15 18 17 20 19 22 21 24 23 26 25 28 27 30 29 32 31 34 33 36 35
Red/Black (8) Black/White (12) Black/Red (16) Red/Green (20) Red/Black-White (24) Black/Red-Green (28) Orange/Black-Green (32) Orange/White-Blue (36) White (2) Green (4)
Red(3)
Black (1) White (2) Green (4) Blue (6) Red/Black (8) Orange/Black (10) Black/White (12) Green/White (14) Black/Red (16) Orange/Red (18)
1 3 5 7 9 11 13 15 17
2 4 6 8 10 12 14 16 18
Red (3) Orange (5) White/Black (7) Green/Black (9) Blue/Red (19) Blue/Black (11) Red/White (13) Blue/White (15) White/Red (17)
1492-CABLEZ
Green/Black/Orange (31) Blue/Black/White (27)
Orange/Black/White (26)
White/Black/Red (23) White/Red/Blue (37) Black/White/Green (38) White/Red (17) Red/White (13) Blue/Black (11) White/Black (7) Black (1) White (2)
Red/Green (20)
Black/White (12)
Black/Red (16)
(High Row)
Row B Row A
(High Row)
Row B
1
1
(Low Row)
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9 10 11 12 13 14 15
9 10 11 12 13 14
1
(Low Row)
2
1 2
3
3
4
4
5
5
6
6
7
7
8
8
9 10 11 12 13
9 10 11 12
Row A
Black/White (12)
Black/Red/Green (28)
Orange/Black/Green (32)
1492-CABA62
Refer to footnote on page 145.
Green/Black/White (25)
1492-CABB62
Black/White/Orange (34)
White/Red/Green (29)
Black/White/Green (38)
Red/Green (20)
Red/Black/White (24)
White (2)
Green/White (14)
Orange/Green (21)
Orange/Red (18)
Blue/Red (19) Blue/White (15) Red (3) Green (4) Green/Black (9) Orange (5)
Black/Red (16)
Green (4)
Red/Black/Green (30)
Black/White/Red (22)
Orange/Black (10)
Green/White (14)
Orange/Red (18)
Red/Black (8)
Blue (6)
143
Pinouts, Continued
White/Red (17) Red/White (13) Blue/Black (11) Orange/Black (10) Red/Black (8) Blue/White (15)
White (2)
7 8
Orange (5)
8
(High Row)
Row B
1
(Low Row)
2 2 3
3 4
4 5
5 6
6 7
7 8
8 9
(High Row)
Row B
1 1 2
2 3
3 4
4 5
5 6
6 7
Row A
(Low Row)
Row A
9 10 11
Orange/Red (18)
Black/Red (16)
Green/White (14)
White (2) Blue/White (15) Black/Red (16) White/Red (17) Orange/Red (18) Red/Black (8) Orange/Black (10)
Black/White (12)
Blue/Red (19) Red/Green (20) Green/Black (9) White/Black (7) Blue (6) Green (4)
Blue/Black (11)
Red/White (13)
Black (1)
Red (3)
9 10
Orange/Black (10)
7 8
1492-CABA64
(High Row)
Row B Row A
1492-CABB64
1 1 2 2 3 3 4 4 5 5 6 6 7 7 8 8 9 10 9 10 11
(Low Row) (High Row)
Row B Row A
2 2 3
3 4
4 5
5 6
6 7
(Low Row)
9 10 11
Green/White (14)
Green/Black (9)
White/Black (7)
Black (1) White (2) Blue/White (15) Black/Red (16) Blue (6) Red/Black (8)
Blue/Red (19)
Black (1)
1492-CABC64
1492-CABF64
Green (4) Blue (6) Red/Black (8) Orange/Black (10) Black/White (12) Green/White (14) Black/Red (16) Orange/Red (18) Blue/Red (19) Red/Green (20)
2 4 6 8 10 12 14 16 18
1 3 5 7 9 11 13 15 17
Red (3) Orange (5) White/Black (7) Green/Black (9) Blue/Black (11) Red/White (13) Blue/White (15) White/Red (17) Black (1) White (2)
Green (4) Blue (6) Red/Black (8) Orange/Black (10) Black/White (12) Green/White (14) Black/Red (16) Orange/Red (18) Blue/Red (19) Red/Green (20)
2 4 6 8 10 12 14 16 18
1 3 5 7 9 11 13 15 17
Red (3) Orange (5) White/Black (7) Green/Black (9) Black (1) White (2) Blue/Black (11) Red/White (13) Blue/White (15) White/Red (17)
Red (3) White/Black (7) Blue/Red (19) Red/Green (20) Blue/Black (11) Blue/White (15)
6 8 10 12 14
5 7 9 11 13
Orange/Black (10) Black (1) Orange (5) Green/Black (9) Red/White (13) White/Red (17)
1492-CABA69
Red (3) Orange (5) White/Black (7) Green/Black (9) Blue/Black (11) Red/White (13) Blue/White (15) White/Red (17) NC
2 4 6 8 10 12 14 16 18 1 3 5 7 9 11 13 15 17
1492-CABB69
White (2) Green (4) Blue (6) Red/Black (8) Black/White (12) Green/White (14) Black/Red (16) Orange/Red (18) NC
1492-CABC69
Black (1) White (2) Green (4) Blue (6) Red/Black (8) Orange/Black (10) Black/White (12) Green/White (14) Black/Red (16) Orange/Red (18)
Red (3) Orange (5) White/Black (7) Green/Black (9) Blue/Black (11) Red/White (13) Blue/White (15) White/Red (17) Blue/Red (19) Red/Green (20)
2 4 6 8 10 12 14 16 18
1 3 5 7 9 11 13 15 17
1492-CABD69
1492-CABE69
White (1) Black (2) Green (4) Blue (6) Red/Black (8) Orange/Black (10) Black/White (12) Green/White (14) Black/Red (16) Orange/Red (18)
Green (4) Blue (6) Red/Black (8) Orange/Black (10) Black/White (12) Green/White (14) Black/Red (16) Orange/Red (18) NC
2 4 6 8 10 12 14 16 18
1 3 5 7 9 11 13 15 17
Red (3) Orange (5) White/Black (7) Green/Black (9) Blue/Black (11) Red/White (13) Blue/White (15) White/Red (17) NC
Green (4) Blue (6) Red/Black (8) Orange/Black (10) Black/White (12) Green/White (14) NC NC Red/Green (20)
2 4 6 8 10 12 14 16 18
1 3 5 7 9 11 13 15 17
Red (3) Orange (5) White/Black (7) Green/Black (9) Blue/Black (11) Red/White (13) NC NC Blue/Red (19)
Red (3) Orange (5) White/Black (7) Green/Black (9) Blue/Red(19) Blue/Black (11) Red/White(13) Blue/White(15) White/Red (17)
2 4 6 8 10 12 14 16 18
1 3 5 7 9 11 13 15 17
1492-CABF69
Refer to footnote on page 145.
1492-CABG69
1492-CABH69
Green/White (14)
Green/Black (9)
144
Pinouts, Continued
R
Orange (5) Green/Black (9) Red/White (13) White/Red (17) White/Black/Green (39) White/Red/Blue (37) Orange/Green (21) Red/Black (8) Black/White (12) Black/Red (16) Red/Green (20) Red/Black/White (24)
2 4 6 8 10 12 14 16 18 1 3 5 7 9 11 13 15 17
White/Black (7) Blue/Black (11) Blue/White (15) Blue/Red (19) White/Black/Red (23) Blue/Black/White (27) Green/Black/Orange (31) White/Red/Orange (35) Black (1) Red (3)
2 4 6 8 10 12 14 16 18
Blue (6) Orange/Black (10) Green/White (14) Orange/Red (18) Black/White/Green (38) Red/White/Green (40) Black/White/Red (22) Orange/Black/White (26) Red/Black/Green (30) Black/White/Orange (34)
3 5 7 9 11 13 15 17
Green/Black/White (25) Black/Red/Green (28) White/Red/Green (29) Orange/Black/Green (32) Blue/White/Orange (33) Orange/White/Blue (36) White (2) Green (4)
1492-CABJ69
L
Orange (5) Green/Black (9) Red/White (13) White/Red (17) Orange/Green (21) Green/Black/White (25) White/Red/Green (29) Blue/White/Orange (33) White/Black/Green (39) White/Red/Blue (37)
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
R
Red (3) Black (1) White/Black (7) Blue/Black (11) Blue/White (15) Blue/Red (19) White/Black/Red (23)
1
2 4 6
3 5
White (2) Green (4) Red/Black (8) Black/White (12) Black/Red (16) Red/Green (20) Red/Black/White (24) Black/Red/Green (28) Orange/Black/Green (32) Orange/White/Blue (36)
Black/White/Red (22) Blue/Black/White (27) Orange/Black/White (26) Green/Black/Orange (31) Red/Black/Green (30) White/Red/Orange (35) Black/White/Orange (34) Black/White/Green (38) Red/White/Green (40)
7 8 9 10 11 12 13 14 15 16 17 18
1492-CABK69
Orange (5) White/Black (7) Green/Black (9) Blue/Black (11) Red/White (13) Blue/White (15) White/Red (17) Blue/Red (19) Black/White-Red (22) NC White/Black-Red (23) Orange/Black-White (26) NC Blue/Black-White (27) Red/Black-Green (30) NC Green/Black-Orange (31) Black/White-Orange (34) NC White/Red-Orange (35)
2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40
1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39
Blue (6) Red/Black (8) Orange/Black (10) Black/White (12) Green/White (14) Black/Red (16) Orange/Red (18) Red/Green (20) NC Orange/Green (21) Red/Black-White (24) NC Green/Black-White (25) Black/Red-Green (28) NC White/Red-Green (29) Orange/Black-Green (32) NC Blue/White-Orange (33) Orange/White-Blue (36)
1492-CABR71
Refer to footnote on page 145. 1492-CABK69 and 1492-CABJ69 are made up of two (2) individual 18-pin terminal blocks connected to a single cable assembly.
145
The I/O module-ready cables have a pre-wired wiring arm or removable terminal block on one end to connect the programmable controller I/O module and 1240 individually colored #18 or #22 AWG conductors on the other. These cables provide the convenience of a pre-wired I/O module connector, while still allowing the flexibility to wire to standard terminal blocks. Pre-wired I/O module connectors include: Catalog Number 1746-N3 40-point plug-in connector (Catalog Number CABLEN3) Bulletin 1746 16-point removable terminal blocks in Red, Blue, and Orange (Catalog Number CABLERTBR, RTBB, RTBO) Catalog Number 1756-TBCH 36-point removable terminal block (Catalog Number CABLETBCH) Catalog Number 1756-TBNH 20-point removable terminal block (Catalog Number CABLETBNH) Catalog Number 1769-RTBN10 8-point removable terminal block (Catalog Number CABLERTN10) Catalog Number 1769-RTBN18 20-point removable terminal block (Catalog Number CABLERTN18) Catalog Number 1769-RTBN32I and 1769-RTBN320 for 32-point 1769 I/O modules Catalog Number 1771-WH 16-point wiring arm (Catalog Number CABLEWH) Catalog Number 1771-WN 32-point wiring arm (Catalog Number CABLEWN) Catalog Number 1771-WHF 16-point fused wiring arm (with fuses) (Catalog Number CABLEWHF) Catalog Number 1771-WD 6-point wiring arm (Catalog Number CABLEWD) Catalog Number 1771-WA 8-point wiring arm (Catalog Number CABLEWA)
Cables are available in lengths of 1.0 m, 2.5 m, and 5.0 m. To order, insert the code for the desired cable length into the catalog number (010 = 1.0 m, 025 = 2.5 m, and 050 = 5.0 m). Example: Catalog Number 1492-CABLE025WH is for a 2.5 m cable with a pre-wired 1771-WH Wiring Arm on one end. Also refer to Build-to-Order Length Cables on page 64.
146
Insulation Rating 300V 80C 300V 80C 300V 80C 300V 80C 300V 80C 300V 80C 300V 80C 300V 80C 300V 80C 300V 80C 300V 80C 300V 80C 300V 80C 300V 80C 300V 80C 300V 80C 300V 80C 300V 80C 300V 80C 300V 80C 300V 80C
Number of Conductors 40 20 20 20 40 20
Conductor Size #22 AWG #18 AWG #18 AWG #18 AWG #18 AWG #18 AWG #18 AWG #22 AWG #18 AWG #18 AWG #22 AWG #22 AWG #18 AWG #18 AWG #22 AWG #22 AWG #18 AWG #18 AWG #18 AWG #18 AWG #18 AWG
11.2 mm (0.44 in.) 1746-N3 (40-Point) Plug-in Connector 11.4 mm (0.45 in.) 1746-RT25B Blue Removable Terminal Block 11.4 mm (0.45 in.) 1746-RT25C Orange Removable Terminal Block 11.4 mm (0.45 in.) 1746-RT25R Red Removable Terminal Block 14.1 mm (0.55 in.) 1756-TBCH (36-Point) Removable Terminal Block 11.4 mm (0.45 in.) 1756-TBNH (20-Point) Removable Terminal Block 13.2 mm (0.52 in.) 1762-L40xxx Output Connector 11.7 mm (0.46 in.) 1762-L40xxx Input Connector 11.4 mm (0.45 in.) 1764-24AWA, -24BWA Output Terminal 11.4 mm (0.45 in.) 1764-28BXB Output Terminal 9.0 mm (0.36 in.) 9.0 mm (0.36 in.) 9.0 mm (0.36 in.) 1764-24AWA, -BWA Input Terminal 1764-28BXBH Input Terminal 1769-RTBN10 Removable Terminal Block
25 40 20 20 20 20
12 20 40 40 12 12 20 20 40
11.4 mm (0.45 in.) 1769-RTBN18 (20-Point) Removable Terminal Block 11.7 mm (0.46 in.) (2) 1769-RTBN18 (20-Point) Removable Terminal Block 11.7 mm (0.46 in.) (2) 1769-RTBN18 (20-Point) Removable Terminal Block 9.0 mm (0.36 in.) 9.0 mm (0.36 in.) 1771-WA (8-Point/10 Terminal) Wiring Arm 1771-WD (6-Point/12 Terminal) Wiring Arm
11.4 mm (0.45 in.) 1771-WH (16-Point/21 Terminal) Wiring Arm 11.4 mm (0.45 in.) 1771-WHF (16-Point/21 Terminal) Fused Wiring Arm 14.1 mm (0.55 in.) 1771-WN (32-Point/40 Terminal) Wiring Arm
Cables are available in lengths of 1.0 m, 2.5 m, and 5.0 m. To order, insert the code for the desired cable length into the catalog number (010 = 1.0 m, 025 = 2.5 m, and 050 = 5.0 m). Example: Catalog Number 1492-CABLE025WH is for a 2.5 m cable with a pre-wired 1771-WH Wiring Arm on one end. Also refer to Build-to-Order Length Cables on page 64.
147
Cables are available in lengths of 1.0 m, 2.5 m, and 5.0 m. To order, insert the code for the desired cable length into the catalog number (010 = 1.0 m, 025 = 2.5 m, and 050 = 5.0 m). Example: Catalog Number 1492-CABLE025WH is for a 2.5 m cable with a pre-wired 1771-WH Wiring Arm on one end. Also refer to Build-to-Order Length Cables on page 64.
148
1492-CABLEN3
1 2
1492-CABLETBCH
2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36
1492-CABLEWN
2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40
2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39
1492-CABLEWH
1492-CABLEWF
39 40
1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
A B C D
00 01 02 03 04 05 06 07 10 11 12 13 14 15 16 17
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
1492-CABLEWD
1 2 3 4 5 6 7 8 9 10 11 12
1492-CABLEWA
1 2 3 4 5 6 7 8 9 10
1492-CABT62
Red/Black/White Green/Black/White Black/White/Red White/Black/Red
White/Red/Green
1492-CABX62
Blue/Black/White Orange/Black/White Green/Black/While Black/Red/Green
Orange/Green
Red/Black/White
White/Black/Red Black/White/Red
Orange/Red Blue/Red
Orange/Green
Red/Green
White Blue/White
Black/Red White/Red
Red/Green
White/Red White
6 8 10 12 14 16 18
(Low Row) (High Row)
Row B
Black
2 1 2
3 3
4 4
5 5
6 6
7 7
8 8
9 10 11 1213 9 10 11 12
(High Row)
Row B Row A
1 1
(Low Row)
2 2
3 3
4 4
5 5
6 6
7 7
8 8
9 1 0 1 1 1 2 1 3 1 41 5 9 10 11 1213 14
Row A
Red
Blue/White Green/White
Blue/Black Orange/Black
Green/Black
Red/White Black/White
White/Black
Red/Black
Orange/Black
Red/White
1492-CABT64
Orange/Green Green/White Blue/White Black/Red White/Red Orange/Red Red/Green
Green//White
Green/Black
Blue/Black Black/White
1492-CABU64
Orange/Red
Blue/Red
Red/Black
Green
Orange
Green
Red
Red/White
Black
(High Row)
Row B Row A
(High Row)
Row B Row A
1 1 2
2 3
3 4
4 5
5 6
6 7
7 8
9 10 9 10 11
1
(Low Row)
Black
5
6
6
7
7
8
(Low Row)
Orange/Black
Red Orange
Green/Black
Green
White/Black
Blue/Red Red/Green
8
9
9 10
10 11
Black/White
Cables are available in lengths of 1.0 m, 2.5 m, and 5.0 m. To order, insert the code for the desired cable length into the catalog number (010 = 1.0 m, 025 = 2.5 m, and 050 = 5.0 m). Example: Catalog Number 1492-CABLE025WH is for a 2.5 m cable with a pre-wired 1771-WH Wiring Arm on one end. Also refer to Build-to-Order Length Cables on page 64. The 1492-CABRTN32F and -RTN320 are made up of two (2) individual 18-pin terminal blocks (L = Left, R=Right) connected to a single cable assembly.
Orange/Black
Green/Black
Blue/Black Black/White
Blue
Red/Black
Blue/Black
Red/Black
Green
White
White
Blue
Orange/Green
Red/White Green/White
Blue/White Black/Red
White/Red
Blue
Black
Black/Red
Blue/Red
Ornage/Red
149
1492-CABX64
White/Yellow White/Orange White/Red White/Brown White/Black Black White/Green White/Blue
1492-CABRTN10
(High Row)
Row B Row A
(High Row)
Row B Row A
1 1 2
2 3
3 4
4 5
5 6
6 7
7 8
8 9
1 1 2
2 3
3 4
4 5
5 6
6 7
7 8
8 9
(Low Row)
(Low Row)
3 4 6 8 10 12
6 8 10 12 14
5 7 9 11 13
1 2 5 7 9 11
White
Yellow Orange
Brown
Violet Blue
Red
White
Yellow Orange
Green
Brown
Violet Blue
Gray
Gray
Red
1492-CABRTN18
Green
1492-CABRTN32I
1492-CABRTN320
R
L 1 2 4 6 8 10 12 14 16 18 R
21,22 1,2 3 5 7 8 9 11 12 13 15 17 18 19,20 14 16 10 4 6
3 4 6 8 10 12 14 16 18 20
2 4 6 8 10 12 14 16 18
1 3 5 7 9 11 13 15 17
1 2 5 7 9 11 13 15 17 19
L
2 4 6 8 10 12 14 16 18
2 4 6 7 8 10 11 12 14 16 17 18 13 15 9 1 3 5
1 3 5 7 9 11 13 15 17
21 24 26 28 30 32 34 36 38
1 3 5 7 9 10 11 12 13 15 17 18 14 16 2 4 6 8
21 23 25 27 29 31 33 35 37
3 5 7 9 11 13 15 17 19 20
23 25 27 29 31 33 35 37 39 40
23 25 27 29 31 32 33 35 37 38 39,40 34 36 28 30 24 26
21 22 24 26 28 30 32 34 36 38
Cables are available in lengths of 1.0 m, 2.5 m, and 5.0 m. To order, insert the code for the desired cable length into the catalog number (010 = 1.0 m, 025 = 2.5 m, and 050 = 5.0 m). Example: Catalog Number 1492-CABLE025WH is for a 2.5 m cable with a pre-wired 1771-WH Wiring Arm on one end. Also refer to Build-to-Order Length Cables on page 64. The 1492-CABRTN32F and -RTN320 are made up of two (2) individual 18-pin terminal blocks (L = Left, R=Right) connected to a single cable assembly.
150
IFM-ready cables have a cable connector on one end to attach to the IFM and either 20 or 40 individually colored conductors on the other end (Catalog Numbers CABLEP and CABLEQ, respectively). These cables allow the IFM to be used in specialty applications that require a custom connection.
IFM-Ready Cable Specifications Catalog Number 1492-CABLEP 1492-CABLEQ Cable Lengths Insulation Rating 300V 80C 300V 80C Number of Conductors 20 40 Conductor Size #22 AWG #22 AWG Nominal Outer Diameter Current/ Compatible Conductor IFM Catalog Numbers 9.0 mm (0.36 in.) 2A 1492-IFM20_ _ _ 1492-XIM20_ _ _ 11.7 mm (0.46 in.) 2A 1492-IFM40_ _ _ 1492-XIM40_ _ _
Each colored conductor is connected to one pin of the molded cable connector as listed in the tables below.
1492-CABLEP Connector Pin Number 1 2 3 4 5 6 7 8 9 10 Wire Color Base/Stripe/Stripe Black White Red Green Orange Blue White/Black Red/Black Green/Black Orange/Black Connector Pin Number 11 12 13 14 15 16 17 18 19 20 Wire Color Base/Stripe/Stripe Blue/Black Black/White Red/White Green/White Blue/White Black/Red White/Red Orange/Red Blue/Red Red/Green
Cables are available in lengths of 1.0 m, 2.5 m, and 5.0 m. To order, insert the desired cable length into the catalog number (010 = 1.0 m, 025 = 2.5 m, and 050 = 5.0 m). Example: Catalog Number 1492-CABLE025P is for a 2.5 m, 20 conductor IFM-ready cable. Also refer to Build-to-Order Length Cables on page 64.
151
Cables are available in lengths of 1.0 m, 2.5 m, and 5.0 m. To order, insert the desired cable length into the catalog number (010 = 1.0 m, 025 = 2.5 m, and 050 = 5.0 m). Example: Catalog Number 1492-CABLE025P is for a 2.5 m, 20 conductor IFM-ready cable. Also refer to Build-to-Order Length Cables on page 64.
152
AIFM Catalog Number 1492-AIFM8-3, -RAIFM8-3 1492-AIFM4-3, -RAIFM4-3 1492-AIFM6S-3, -RAIFM6S-3 1492-AIFM6TC-3
Page No. for Application Notes, and Pinout 154 153 154 155
Page No. for Page No. for Application Specifications Notes, and Pinout 156 157 158 159 214 214 214 214
Page No. for Page No. for Application Specifications Notes, and Pinout 160 162 161 214 214 214
For all AIFM dimensions, refer to page 181. For general Adhesive Label Card information, refer to page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web page at http://www.ab.com/raise. Refer to page 200 for specific platform web site information. Refer to the online documentation for new product information.
Symbols and Terminal Identification Conventions Used Throughout the Pinout Section
1492-AIFM Field-Side Terminal 1492 Pre-Wired Cable I/O Module Connection Fuse and Blown Fuse Indicator One-Pole DIP Switch Two-Pole DIP Switch 1492-AIFM and Cable Connection (D-Shell Pin) Test Point
Field-Side Terminal Identification Convention:
C1 C2 C3 C4 C5 . . .
B1 B2 B3 B4 B5 . . .
B1
B2
B3
B4
B5 . . .
A1 A2 A3 A4 A5 . . .
A1
A2
A3
A4
A5 . . .
153
1492-AIFM4-3 1492-RAIFM4-3
Feed-Through 4-channel Input, Output or 2-in/2-out Combination with 3 Terminals/Channel
Pinout
2 A3 B3 A7 B7 A1
1 TP1 8 TP2
15 TP3 14 TP4
A2
A5
13
A6 TP5 TP6 B1
Application Notes
12
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the AIFM. 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. DIP Switches Selectable resistors are available to current limit the Catalog Numbers 1771-OFE2 and -OFE3 output circuits. By opening the switch (off or down position), 250 series impedance is inserted into the output circuit. Default switch position is on/closed/no series impedance. Do not exceed maximum loop impedance of output module (1200 for -OFE2; 450 for -OFE3). 4. Test Points With optional 250 series impedance in output circuit (refer to DIP Switches), test points can be used to measure loop voltage/current. Refer to the Pinout for test point circuit location. 5. Shield Terminals Four field-side terminals are jumpered together on the AIFM and internally connected to the D-shell housing. 6. Dimensions Refer to page 183.
11 TP7 10 TP8
B2
B5
9 D-Shell Housing
B6
A4 A8 B4 B8
154
1492-AIFM6S-3 1492-RAIFM6S-3
Feed-Through 6-Channel Isolated with 3...4 Terminals/Channel
1492-AIFM8-3 1492-RAIFM8-3
Feed-Through 8-Channel Differential 16-Channel SingleEnded with 3 Terminals/Channel
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the AIFM. 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Shield Terminals Six field-side terminals are jumpered together on the AIFM and internally connected to the D-shell housing. 4. Dimensions Refer to page 183.
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the AIFM. 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Extra Terminals Eight field-side terminals are jumpered together on the AIFM. For some I/O modules, the terminals are also internally connected to module common through the prewired cable. Refer to the AIFM and ACABLE pinouts. 4. Shield Terminals Eight field-side terminals are jumpered together on the AIFM and internally connected to the D-shell housing. 5. Dimensions Refer to page 183.
Pinout
13 12 25 24 11 23 22 9 21 19 6 18 17 4 16 15 2 14 D-Shell Housing A2 A4 A6 A8 A10 A12 B1 A1 B2 B3 A3 B4 B5 A5 B6 B7 A7 B8 B9 A9 B10 B11 A11 B12
Pinout
3 2 1 14 15 16 17 18 12 13 25 24 23 22 20 21 B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 B11 B12 B13 B14 B15 B16
4 6 8 10 19
155
1492-AIFM6TC-3
Thermocouple 6-Channel with 3 Terminals/Channel
Pinout
13 25 24 23 22 21 19 18 17 16 15 14 6 T 20 12 A1 A3 A5 A9 A11 B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 B11 B12 A7
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the AIFM. 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Shield Terminals Six field-side terminals are jumpered together on the AIFM and internally connected to the D-shell housing. 4. Cold Junction Compensation This AIFM contains on-board cold junction compensation (CTC) through a thermistor (T) and isothermal bar mounted to the field-side terminals. Do not install the cold junction sensor (provided with the Catalog Number 1756-IT6I or 1756-IT6I2 thermocouple input module) on the removable terminal block of the pre-wired cable. This module is NOT compatible with other PLC systems (e.g. bulletin numbers 1746, 1771, etc.) that do not have external CJC capability. 5. Dimensions Refer to page 183.
11 9 4 2
156
1492-AIFM4C-F-5
Fusible 2-channel Input, 2-Channel Output with 24V DC Blown Fuse Indicators, Test Points, 5 Terminals/Input, 3 Terminals/Output
Pinout
8 B1 15 B2
14
B3
13
B4
12
B5
11
B6
2 10 9
B7 B8 B9 B10 B11 TP1 TP2 A1 TP3 TP4 A2 B12 A5 . . . . A8 D-Shell Housing A9 . . . . A12
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the AIFM. 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Fusing Fuse holders are included with the AIFM. Fuses (5 x 20 mm) are not included. Do not exceed 2 A per input, 12 A per AIFM. 4. Isolation The fuse clips and blown fuse indicators are internally connected to one power source field-side terminal. All inputs must reference the same power source. 5. DIP Switches For ease of wiring, unused inputs can be jumpered to module common by closing the DIP switches (ON position) for analog modules that have this capability. Default switch position is OPEN/OFF/NOT jumpered together. 6. Test Points When using a two-wire transmitter, test points (TP1-TP2) can be used to measure input loop current. Refer to the Pinout for test point circuit location. 7. Extra Terminals Four field-side terminals are internally jumpered on the AIFM. They can be used for power source common connections. 8. Shield Terminals Four field-side terminals are jumpered together on AIFM and internally connected to the D-shell housing. 9. Dimensions Refer to page 183.
157
1492-AIFM4I-F-5
Fusible 4-Channel Input with 24V DC Blown Fuse Indicators, Test Points, 5 Terminals/Input
Pinout
8 B1 15 B2
14
B3
13
B4
12
B5
11 2
B6 B7
10
B8
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the AIFM. 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Fusing Fuse holders are included with the AIFM. Fuses (5 x 20 mm) are not included. Do not exceed 2 A per input, 12 A per AIFM. 4. Isolation The fuse clips and blown fuse indicators are internally connected to one power source field-side terminal. All inputs must reference the same power source. 5. DIP Switches For ease of wiring, unused inputs can be jumpered to module common by closing the DIP switches (ON position) for analog modules that have this capability. Default switch position is OPEN/OFF/NOT jumpered together. 6. Test Points When using a two-wire transmitter, test points (TP1-TP2) can be used to measure input loop current. Refer to the Pinout for test point circuit location. 7. Extra Terminals Four field-side terminals are internally jumpered on the AIFM. They can be used for power source common connections. 8. Shield Terminals Four field-side terminals are jumpered together on the AIFM and internally connected to the D-shell housing. 9. Dimensions Refer to page 183.
9 1
TP7
TP8
158
1492-AIFM8-F-5
Fusible 8-Channel Input with 24V DC Blown Fuse Indicators, 5 Terminals/Channel
Pinout
3 C1 2 1
C2 C3
14 15
C4 C5
16 17
C6 C7
18 12
C8 C9
13 25
C10 C11
24 23
C12 C13
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the AIFM. 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Fusing Fuse holders are included with the AIFM. Fuses (5 x 20 mm) are not included. Do not exceed 2 A per input, 12 A per AIFM. 4. Isolation The fuse clips and blown fuse indicators are internally connected to one power source field-side terminal. All inputs must reference the same power source. 5. DIP Switches For ease of wiring, unused inputs can be jumpered to module common by closing the DIP switches (ON position) for analog modules that have this capability. Default switch position is OPEN/OFF/NOT jumpered together. 6. Extra Terminals Nine field-side terminals are internally jumpered on the AIFM. They can be used for power source common connections. 7. Shield Terminals Eighteen field-side terminals are jumpered together on the AIFM and internally connected to the D-shell housing. 8. Dimensions Refer to page 183.
22 20
C14 C15
21 6 19
C16
159
1492-AIFM16-F-3
Fusible 16-Channel Inputs with 24V DC Blown Fuse Indicators, 3 Terminals/Channel
Pinout
3 2 1 14 15 16 17 18 12 B2 B3 B4 B5 B6 B7 B8 B9 B10 B11 B12 B13 B14 B15 B16 B17 B18 B1 C1 . . . . . C16 D-Shell Housing A1 . . . . . A18
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the AIFM. 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Fusing Fuse holders are included with the AIFM. Fuses (5 x 20 mm) are not included. Do not exceed 2 A per input, 12 A per AIFM. 4. Isolation The fuse clips and blown fuse indicators are internally connected to one power source field-side terminal. All inputs must reference the same power source. 5. DIP Switches For ease of wiring, unused inputs can be jumpered to module common by closing the DIP switches (ON position) for analog modules that have this capability. Default switch position is OPEN/OFF/NOT jumpered together. 6. Shield Terminals Eighteen field-side terminals are jumpered together on the AIFM and internally connected to the D-shell housing. 7. Dimensions Refer to page 183.
13 25 24 23 22 20 21 4 6 8 10 19
160
1492-AIFM16-F-5
Fusible 16-Channel Input with 24V DC Blown Fuse Indicators, 5 Terminals/Channel
TB2
TB1
6. Extra Terminals Sixteen field-side terminals (C9C16 on TB1 and TB2) are internally jumpered on the AIFM and connected to module common. Eighteen field-side terminals (B10B18 on TB1 and TB2) are internally jumpered on the AIFM and can be used for power source common connections. There are two field-side terminals (A17 and A18 on TB1) that can be externally jumpered to connect the two groups of field-side terminals. 7. Shield Terminals Sixteen field-side terminals are jumpered together on the AIFM and internally connected to the D-shell housing. 8. Dimensions Refer to page 183.
TB1
C1 C2 C3 C4 C5 C6 C7 C8 C9 . . . . C16 A17
4 6 8 10 19
TB2
12 13 25 24 23 22 20 21 C1 C2 C3 C4 C5 C6 C7 C8 C9 . . . . C16
B1 B2 . . . . . B9 B10 . . . B18
D-Shell Housing
SH
A1 . . . A8
A1 . . . A8
161
1492-AIFMQS
Fusible 4-Input/4 Output Channel with 8 Fuses & 24V DC Blown Fuse Indicators
Pinout
+INT 1 -INT 1 +RET 1 -RET 1 +OUT 1 OUT COM +INT 2 -INT 2 +RET 2 -RET 2 +OUT 2 OUT COM +INT 3 -INT 3 +RET 3 -RET 3 +OUT 3 OUT COM +INT 4
6 18 20 19 5 17 3 15 4 16 2 Black/Blue Blue/Black Black/Orange Red/Gray Gray/Red Red/Brown Brown/Red Red/Green Green/Red Red/Orange Orange/Red 4 5 15 6 9 8 22 14 23 24 18 12 24 13 25 11 23 9 21 10 22 8 Red/Blue White/Gray Gray/White White/Brown Brown/White White/Green Green/White White/Orange Orange/White White/Blue Blue/White 1 11 2 3 17 26 10 19 20 12 25
+ Interrogate 1 - Interrogate 1 + Return 1 - Return 1 Drive Output 1 Drive Common + Interrogate 2 - Interrogate 2 + Return 2 - Return 2 Drive Output 2
+ Interrogate 3 - Interrogate 3 + Return 3 - Return 3 Drive Output 3 Drive Common + Interrogate 4 - Interrogate 4 + Return 4 - Return 4 Drive Output 4
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the AIFM. 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Fusing Fuse holders are included with the AIFM. Fuses (5 x 20 mm) are not included. Do not exceed 3 A per input, 12 A per AIFM. 4. Isolation The fuse clips and blown fuse indicators are internally connected to two separate power source field-side terminals. All inputs within a group must reference the same power source. 5. Extra Terminals Four field-side terminals (on TB1) are internally jumpered on the AIFM and connected to module common. Four field-side terminals (on TB1) are internally jumpered on the AIFM and can be used for power source common connections. 6. Shield Terminals Eight field-side terminals are jumpered together on the AIFM and internally connected to the D-shell housing. 7. Dimensions Refer to page 183.
-INT 4 +RET 4 -RET 4 +OUT 4 OUT COM COM LDT COM LDT COM GND SH SH -V -V1F -V4F +V +V1F +V4F
7 1
Blue/Red
21 13
Orange/Black
DRAIN
162
1492-AIFMPI
Fusible 8-Input/2 Output Channels
Application Notes
1. Compatibility To ensure proper operation with the I/O module, do not exceed the voltage and current ratings of the AIFM. 2. Wiring Refer to the Label Section on page 175. For Field-Side Wiring Diagrams, refer to the Wiring System web site information on page 200. 3. Fusing Two fuse holders for the outputs are included with the AIFM. Eight fuses (0.25 A, 5 x 20 mm) are included with the fused supply inputs. Do not exceed 2 A per output. 4. Isolation The fuse clips and blown fuse indicators are internally connected to one power source field-side terminal. All inputs must reference the same power source. 5. Jumpers J0J7 provide the option of connecting the negative inputs to the return. J8 commons the shield to the return. Default switch position is OPEN/OFF/NOT jumpered together. 6. Shield Terminals Eight field-side terminals are jumpered together on the AIFM and internally connected to the D-shell housing. 7. The 1492-AIFMPI is designed exclusively for the 1757-PIM module. 8. Dimensions Refer to page 183.
Pinout
Refer to page 163.
163
1492-AIFMPI, Continued
Pinout, Continued
CN
1 2 3
TB
+
J0
TB
B9 V0 +24
CHANNEL 0
F0
B2
+
1 2 3 1 2 3 J7
F1
B4
CHANNEL 7
B1
F2
B6
9 22 SHELL
J8
F3
B3 B5 B7 B10 B12 B14 B16 V0 A9 RTN
SHIELD IN 0...7
B8
+V FUSED 0-7
F4
B11
F5
B13
F6
B15
F7
B17 12 24
CHANNEL 0 1 2 3 4 5 6 7
4 14 3 15 2 16 1 17 8 18 7 19 6 20 5 21 A1 +0 A2 0 A3 +1 A4 1 A5 +2 A6 2 A7 +3 A8 3 A10 +4 A11 4
IN IN
B18
F8
25 B19
IN 13 IN IN
F9
B20
164
Bulletin 1492 pre-wired cables are designed to minimize control wiring in a panel. Analog pre-wired cables, when used with an AIFM, replace the pointto-point wiring between Allen-Bradley programmable controller I/O modules and individual terminal blocks. The analog ready-to-wire cables provide one end of the cable pre-terminated for an AIFM (AIFM-ready cable).
Digital/Analog Programmable Controller Wiring Systems
Pre-Wired Cables
Specifications
The pre-wired cables have a Bulletin 1746 Removable Terminal Block, Bulletin 1756 Removable Terminal Block, Bulletin 1769 Removable Terminal Block, or Bulletin 1771 Wiring Arm on one end and a D-shell on the other to connect to the AIFM. All analog cables have an overall shield and most have #22 AWG twisted pairs for additional noise immunity. In addition, most analog cables have prepared ring lugs on the drain wire for convenient grounding of the cable shield to the programmable controller chassis. The broad offering of analog pre-wired cables supports over 26 different Bulletin 1746, 1756, 1769, and 1771 analog, RTD, and thermocouple I/O modules.
165
AIFM Connector 15-pin D-shell 15-pin D-shell 25-pin D-shell 25-pin D-shell 25-pin D-shell 25-pin D-shell 15-pin D-shell 25-pin D-shell 25-pin D-shell 15-pin D-shell 25-pin D-shell 25-pin D-shell 25-pin D-shell 25-pin D-shell 25-pin D-shell 25-pin D-shell 25-pin D-shell 25-pin D-shell 25-pin D-shell 25-pin D-shell 25-pin D-shell 25-pin D-shell 25-pin D-shell 25-pin D-shell 25-pin D-shell 25-pin D-shell 15-pin D-shell 15-pin D-shell 25-pin D-shell 25-pin D-shell 15-pin D-shell 15-pin D-shell 15-pin D-shell 15-pin D-shell 15-pin D-shell 15-pin D-shell 25-pin D-shell 25-pin D-shell 25-pin D-shell 25-pin D-shell 25-pin D-shell 25-pin D-shell
No. of Conductors 5 Twisted Pairs 5 Twisted Pairs 9 Twisted Pairs 20 Conductors 9 Twisted Pairs 20 Conductors 5 Twisted Pairs 9 Twisted Pairs 20 Conductors 5 Twisted Pairs 11 Twisted Pairs 12 Twisted Pairs 20 Conductors 9 Twisted Pairs 9 Twisted Pairs 9 Twisted Pairs 20 Conductors 20 Conductors 20 Conductors 20 Conductors 5 Twisted Pairs 5 Twisted Pairs 20 Conductors 20 Conductors 9 Twisted Pairs 9 Twisted Pairs 20 Conductors 20 Conductors 9 Twisted Pairs 9 Twisted Pairs 5 Twisted Pairs 5 Twisted Pairs 5 Twisted Pairs 5 Twisted Pairs 5 Twisted Pairs 5 Twisted Pairs 20 Conductors 20 Conductors 20 Conductors 20 Conductors 20 Conductors 20 Conductors
Insulation Rating 300V 80C 300V 80C 300V 80C 300V 80C 300V 80C 300V 80C 300V 80C 300V 80C 300V 80C 300V 80C 300V 80C 300V 80C 300V 80C 300V 80C 300V 80C 300V 80C 300V 80C 300V 80C 300V 80C 300V 80C 300V 80C 300V 80C 300V 80C 300V 80C 300V 80C 300V 80C 300V 80C 300V 80C 300V 80C 300V 80C 300V 80C 300V 80C 300V 80C 300V 80C 300V 80C 300V 80C 300V 80C 300V 80C 300V 80C 300V 80C 300V 80C 300V 80C
Conductor Size 22 AWG 22 AWG 22 AWG 22 AWG 22 AWG 22 AWG 22 AWG 22 AWG 22 AWG 22 AWG 22 AWG 22 AWG 22 AWG 22 AWG 22 AWG 22 AWG 22 AWG 22 AWG 22 AWG 22 AWG 22 AWG 22 AWG 22 AWG 22 AWG 22 AWG 22 AWG 22 AWG 22 AWG 22 AWG 22 AWG 22 AWG 22 AWG 22 AWG 22 AWG 22 AWG 22 AWG 22 AWG 22 AWG 22 AWG 22 AWG 22 AWG 22 AWG
Nominal Outer Diameter 7.44 mm (0.293") 7.44 mm (0.293") 6.78 mm (0.267") 8.43 mm (0.332") 6.78 mm (0.267") 8.43 mm (0.332") 7.44 mm (0.293") 6.78 mm (0.267") 8.43 mm (0.332") 7.44 mm (0.293") 11.5 mm (0.45") 10.2 mm (0.40") 8.43 mm (0.332") 6.78 mm (0.267") 6.78 mm (0.267") 6.78 mm (0.267") 8.43 mm (0.332") 10.2 mm (0.40") 8.43 mm (0.332") 8.43 mm (0.332") 8.43 mm (0.332") 8.43 mm (0.332") 8.43 mm (0.332") 8.43 mm (0.332") 6.78 mm (0.267") 6.78 mm (0.267") 8.43 mm (0.332") 8.43 mm (0.332") 6.78 mm (0.267") 6.78 mm (0.267") 7.44 mm (0.293") 7.44 mm (0.293") 7.44 mm (0.293") 7.44 mm (0.293") 7.44 mm (0.293") 7.44 mm (0.293") 8.43 mm (0.332") 8.43 mm (0.332") 8.43 mm (0.332") 8.43 mm (0.332") 8.43 mm (0.332") 8.43 mm (0.332")
1746-RT28 12-Position Removable Terminal Block 1746-RT26 2-Position and 1746-RT27 8-Position Removable Terminal Block 1746-RT25G Green Removable Terminal Block 1746-RT25G Green Removable Terminal Block 1771-WG (21 terminal) 1771-WG (21 terminal) Wiring Arm 1771-WC (10 terminal) Wiring Arm 1771-WF (18 terminal) Wiring Arm 1771-WF (18 terminal) Wiring Arm 1746-RT28 12-Position Removable Terminal Block 1756-TBCH 36-Position Removable Terminal Block 1746-QS (26 terminal D-shell) 1746-RT25G Green Removable Terminal Block 1756-TBNH 20-Position Removable Terminal Block 1756-TBNH 20-Position Removable Terminal Block 1756-TBNH 20-Position Removable Terminal Block 1756-TBNH 20-Position Removable Terminal Block 1746-RT25G Green Removable Terminal Block 1756-TBCH 36-Position Removable Terminal Block 1756-TBCH 36-Position Removable Terminal Block 1756-TBCH 36-Position Removable Terminal Block 1756-TBCH 36-Position Removable Terminal Block 1756-TBCH 36-Position Removable Terminal Block 1756-TBCH 36-Position Removable Terminal Block 1756-TBCH 36-Position Removable Terminal Block 1756-TBCH 36-Position Removable Terminal Block 1756-TBNH 20-Position Removable Terminal Block 1756-TBNH 20-Position Removable Terminal Block 1756-TBNH 20-Position Removable Terminal Block 1756-TBNH 20-Position Removable Terminal Block 1769-RTBN10 12-Position Removable Terminal Block 1769-RTBN10 12-Position Removable Terminal Block 1769-RTBN18 20-Position Removable Terminal Block 1769-RTBN18 20-Position Removable Terminal Block 1769-RTBN18 20-Position Removable Terminal Block 1769-RTBN18 20-Position Removable Terminal Block 1769-RTBN18 20-Position Removable Terminal Block 1769-RTBN18 20-Position Removable Terminal Block 1769-RTBN18 20-Position Removable Terminal Block 1769-RTBN18 20-Position Removable Terminal Block 1769-RTBN18 20-Position Removable Terminal Block 1769-RTBN18 20-Position Removable Terminal Block
Cables are available in standard lengths of 0.5 m, 1.0 m, 2.5 m and 5.0 m. To order, insert the desired cable length code into the catalog number (005 = 0.5 m, 010 = 1.0 m, 025 = 2.5 m, and 050 = 5.0 m). Example: Catalog Number 1492-ACABLE005A is for a 0.5 m cable for the 1746-NI4 I/O Module. Also refer to Build-to-Order Length Cables on page 64. All pre-wired analog cables have an overall shield. On 1492-ACABLEC and 1492-ACABLED, the drain wire is connected to the shield terminal on the I/O module connector. All other 1492-ACABLEs have a ring lug on the 7.87" (200 mm) exposed drain wire at the I/O module end of the cable. Not every connection is always used.
166
Pinouts
Analog Pre-Wired Cables
The following diagrams indicate how the analog pre-wired cables are connected on both ends. The description listed first is the wire color of the conductor connected to the screw terminal on the respective Wiring Arm or Removable Terminal Block. The number that follows in parentheses is the corresponding pin number in the D-shell connector on the other end.
Shield Base Color Stripe Color
15
25
1 1 1
14
13
167
Pinouts, Continued
NC Red (3) Black (2) White (1) Black (14) 0 1 2 3 4 5 6 7 8 9 10 11 Black (1) NC Blue (10) Black (9) Yellow (2) Green (12) Black (11) 4 5 6 7 Green (12) Black (11) Blue (10) Black (9) Drain NC White (14) Black (13) 0 1 2 3 Red (8) Black (15) White (14) Black (13) Red (8) Black (15) 0 1 Green (15) Black (16) Blue (17) Black (18) Yellow (12) Black (13) Brown (25) Black (24) Orange (23) Black (22) Red (20) White (21)
1492-ACABLE___A
1492-ACABLE___B
1492-ACABLE___C
1 2 3 4 5 NC
1 2 3 4 5
Red (3) Brown (2) Black (1) White (14) Orange (4) White/Black (15) White/Brown (16) White/Red (17) White/Orange (18) Blue (10) Violet (12) Gray (13) White/Black/Brown (25) White/Gray (24) Green (8) White/Violet (23) White/Blue (22) White/Yellow (20) White/Green (21) Yellow (6) NC
NC NC Blue (13) White/Blue (24) White/Violet (25) White/Green (23) Green (12) Yellow (11) NC NC White/Yellow (22) White/Red (19) White/Orange (21) White/Brown (18) Orange (9) Red (6) NC Drain
6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 NC NC
6 7 8 9 10
11 12 13 14 15
Orange (23) Black (22) Red (20) White (21) Red (6) Green (19)
16 17 18 19 20 21
1492-ACABLE___D
1492-ACABLE___E
1492-ACABLE___F
168
Pinouts, Continued
18 16 14
Red (8) Black (15) White (14) Black (13) Green (12) Black (11) Blue (10) Black (9) NC NC
A 0
12 10 NC NC
Red (3) Black (2) White (1) Black (14) Green (15) Black (16) Blue (17) Black (18)
18 16 14 12 10
1 2 3 4 5
2 8 6 4
6 7 B
Yellow (12) Black (13) Brown (25) Black (24) Orange (23) Black (22) Red (20) White (21)
8 6 4 2
White/Violet (25) Green (12) Blue (13) White/Green (23) Yellow (11) White/Blue (24) White/Orange (21) Orange (9) White/Yellow (22) White/Brown (18) Red (6) White/Red (19) White (16) Brown (4) White/Black (17) Violet (14) Black (2) Gray (15)
0 1 2 3 4 5 6 7 8 9 10 11 NC NC NC NC
1492-ACABLE___G
(3) White (15) Black
NC NC
2 1
1492-ACABLE___H
Red (4) Black (14)
NC NC
1492-ACABLE___J
1492-ACABLE___L
(1) Blue (17) Black (7) Brown (19) Black (5) Red (21) White (24) Red (13) Blue
36 35
Red/Brown (5) Brown/Red (17) Red/Green (20) Green/Red (19) Orange/Red (18) Red/Orange (6) Orange/White (25) White/Orange (13) Blue/White (24) White/Blue (12)
1
18 26
NC NC
10
19
1492-ACABLE___M
White/Black (15) NC White/Brown (16) NC White/Red (17) NC White/Orange (18) NC Violet (12) NC Gray (13) Green (8) White-Black/Brown (25) Orange (4) White/Gray (24) Red (3) Brown (2) NC White/Yellow (20) White/Green (21)
1492-ACABLE___Q
1492-ACABLE___R
169
Pinouts, Continued
Red (3) Black (1) White/Black (15) White/Red (17) Orange (4) Yellow (6) Violet (12) White/Black/Brown (25) White/Violet (23) White/Yellow (20)
2 4 6 8 1 3 5 7
10 9 12 11 14 13 16 15 18 17 20 19 22 21 24 23 26 25 28 27 20 29 32 31 34 33 36 35
White/Brown (16)
Brown (2) White (14) White/Brown (16) White/Orange (18) Gray (13) White/Gray (24) White/Blue (22) White/Green (21)
10 9 12 11 14 13 16 15 18 17 20 19 22 21 24 23 26 25 28 27 30 29 32 31 34 33 36 35
1492-ACABLE___TA
Red (3) Black (2) White (1) Black(14) Green (15) Black (16) Blue (17) Black (18)
1492-ACABLE___TB
2 4 6 8
1 3 5 7
10 9 12 11 14 13 16 15 18 17 20 19 22 21 24 23 26 25 28 27 30 29 32 31 34 33 36 35
Red (3) Black (2) White (1) Black(14) Green (15) Black (16) Blue (17) Black (18)
2 4 6 8
1 3 5 7
10 9 12 11 14 13 16 15 18 17 20 19 22 21 24 23 26 25 28 27 30 29 32 31 34 33 36 35
Red (3) Brown (2) Black (1) White (14) Orange (4) White/Black (15) White/Brown (16) White/Red (17) White/Orange (18) Violet (12) Gray (13) White/Black/Brown (25) White/Gray (24) Blue (10) White/Violet (23) White/Blue (22) White/Yellow (20) White/Green (21)
2 4 6 8
1 3 5 7
10 9 12 11 14 13 16 15 18 17 20 19 22 21 24 23 26 25 28 27 30 29 32 31 34 33 36 35
Yellow (6)
Green (8)
1492-ACABLE___TC
Red (3) Brown (2) Black (1) White(14)
1492-ACABLE___TD
Red (3) Black (2) White (1) Black(14) Green (15) Black (16) Blue (17) Black (18) Yellow (12) Black (13) Brown(25) Black (24) Orange (23) Black (22) Red (20) White (21)
1492-ACABLE___UA
2 4 6 8 1 3 5 7
2 4 6 8
1 3 5 7
Orange (4) Yellow (6) White/Black (15) White/Brown (16) White/Red (17) White/Orange (18) Violet (12) Gray (13) White/Black/Brown (25) White/Gray (24) Green (8) Blue (10) White/Violet (23) White/Blue (22) White/Yellow (20) White/Green (21)
10 9 12 11 14 13 16 15 18 17 20 19 22 21 24 23 26 25 28 27 30 29 32 31 34 33 36 35
Red (3) Black (2) White (1) Black(14) Green (15) Black (16) Blue (17) Black (18) Yellow (12) Black (13) Brown(25) Black (24) Orange (23) Black (22) Red (20) White (21)
2 4 6 8
1 3 5 7
J1 J2 J3 J4 J5 J6
10 9 12 11 14 13 16 15 18 17 20 19 22 21 24 23 26 25 28 27 30 29 32 31 34 33 36 35
10 9 12 11 14 13 16 15 18 17 20 19 22 21 24 23 26 25 28 27 30 29 32 31 34 33 36 35
J7 J8
1492-ACABLE___UB
1492-ACABLE___UC
1492-ACABLE___UD
170
Pinouts, Continued
2 4 6 8
1 3 5 7
1 3 5 7
4 6 8
10 9 12 11 14 13 16 15 18 17 20 19
10 9 12 11
14 13 16 15 18 17 20 19
1492-ACABLE___VA
1492-ACABLE___VB
1 3 5 7
4 6 8
10 9 12 11
14 13 16 15 18 17 20 19
1492-ACABLE___WA
1 3 5 7
Yellow (12) Black (13) Black (24) Brown (25) Black (22) Orange (23) White (21) Red (20)
4 6
NC
10 9 12 11 14 13 16 15
NC
18 17 20 19
1492-ACABLE___WB
171
Pinouts, Continued
Blue (24)
2 4
1 3 5 7
Red (13)
Blue (24) NC
2 4 6 8
1 3 5 7
Red (13) NC Black (25) White (22) NC Black (21) NC Green (17) NC Black (16)
6 8
10 9
10 9
12 11 14 13 16 15 18 17
12 11 14 13 16 15 18 17 20 19
Black (14)
20 19
Black (16)
Black (14)
1492-ACABLE___X
Black (23) Blue (24)
1492-ACABLE___Y
2 4 6 8
1 3 5 7
Blue (13) Green (12) White/Violet (25) White/Yellow (22) Orange (9) White/Orange (21) NC White/Black (17) Brown (4) White (16)
2 4 6 8
1 3 5 7
White/Green (23) White/Red (19) Red (6) White/Brown (18) NC Gray (15) Black (2) Violet (14)
10 9 12 11 14 13 16 15 18 17 20 19
10 9 12 11 14 13 16 15 18 17 20 19
1492-ACABLE___Z
Red(3) Black (1) Violet (15) White (17) Orange (6) Yellow (12) White/Violet (25) White/Green (23) White/Red (20)
1 3 5 7 9 11 13 15 17
2 4 6 8 10 12 14 16 18
Brown (2) Blue (14) Gray (16) White/Black (18) White/Brown (19) Green (13) White/Blue (24) White/Yellow (22) White/Orange (21)
1492-ACABLE___YT
172
Pinouts, Continued
NC NC NC NC NC
2 4 6 8 10
1 3 5 7 9
2 4 6 8 10
1 3 5 7 9
1492-ACAB___AA69
1492-ACAB___AB69
2 4 6 8 10 12 14 16 18
1 3 5 7 9 11 13 15 17
Red (8) White (14) Green (12) Blue (10) Black (9)
2 4 6 8 10 12 14 16 18
1 3 5 7 9 11 13 15 17
Red (8) White (14) Green (12) Blue (10) Black (9)
1492-ACAB___BA69
1492-ACAB___BB69
1 3 5 7 9 11 13 15 17
NC NC NC NC NC
4 6 8 10 12 14 16 18
NC NC NC NC NC
Red (8) Black (15) White (14) Black (13) Green (12) Black (11) Blue (10) Black (9) NC NC NC NC NC
2 4 6 8 10 12 14 16 18
1 3 5 7 9 11 13 15 17
Black (15) Red (8) Black (13) White (14) Black (11) Green (12) Black (9) Blue (10)
1492-ACAB___BC69
1492-ACAB___BD69
173
Pinouts, Continued
R
1 2 4 6 7 8 10 11 12 14 13 15 16 17 18 9 3 5
R
1 2 4 3 5 6 7 8 9 11 12 1 3 5
Red (3) Black (1) White/Black (15) White/Red (17) White/Green (21) Orange (4)
2 4 6 8 10 11 12 14 16 17 18 13 15 7 9 3 5
Violet (12) White/Black/Brown (25) White/Violet (23) White/Yellow (20) Yellow (6)
2 4 6 8 10
7 9 11
10 13 15 16 17 18
12 14 13 15 16 17 18
14
Yellow (6)
1492-ACAB___EA69
L
1492-ACAB___EB69
R
1 2 4 3 5 6 7 8 9 11 12
Brown (2) White (14) White/Brown (16) White/Orange (18) Yellow (6)
2 4 6 8 10
1 3 5 7 9 11
10 13 15 16 17 18
White/Red (17)
12
14
14 16
13 15 17
18
1492-ACAB___EC69
L
1
R
1 2 4 3 5 6 7 8
Brown (2) White (14) White/Brown (16) White/Orange (18) Yellow (6)
Red (3)
2 4 3 5 6 8 7 9 10 11 12 14 16 17 18 13 15
9 11
10 12 14 16 17 18 13 15
1492-ACAB___ED69
White/Red (19) Red (6) White/Brown (18) White/Black (17) Brown (4) White (16) Gray (15) Black (2) Violet (14)
2 4 6 8 10 12 14 16 18
1 3 5 7 9 11 13 15 17
Blue (13) Green (12) White/Violet (25) White/Blue (24) Yellow (11) White/Green (23) White/Yellow (22) Orange (9) White/Orange (21)
White/Black (15) White/Brown (16) White/Red (17) White/Orange (18) Violet (12) Gray (13) White/Blue/Brown (25) Orange/Red (18) Red (3) Brown (2)
2 4 6 8 10 12 14 16 18
1 3 5 7 9 11 13 15 17
Yellow (6)
1492-ACAB___C69
Cable is made up of two (Left & Right pair) individual terminal blocks.
1492-ACAB___D69
174
Dimensions
Approximate dimensions are shown in millimeters unless otherwise indicated (to convert to inches, multiply by 0.0394). Dimensions are not to be used for manufacturing purposes.
29 mm (1.15 in.)
1.6 in. 39 mm
1.8 in. 44 mm
2.3 in. 58 mm
The following is an example to show the length (L) and width (W) and Height (H) dimension layout for a Wiring System Module. Refer to the Quick Reference table on Page 181 for a complete list of module dimensions.
Height
Length
Width
175
Marking Systems
176
Part 1 of Adhesive Label Card for Catalog Numbers 1492-IFM20F, -IFM20D24, and -IFM20D120
MODULE LABEL
IN 0 IN 00
IN 1 IN 01
IN 2 IN 02
IN 3 IN 03
IN 4 IN 04
IN 5 IN 05
IN 6 IN 06
IN 7 IN 07
IN 8 IN 10
IN 9 IN 11
IN 10 IN 12
IN 11 IN 13
IN 12 IN 14
IN 13 IN 15
IN 14 IN 16
IN 15 IN 17
L2 L2
L2 L2
IN 0 IN 00
IN 1 IN 01
IN 2 IN 02
IN 3 IN 03
IN 4 IN 04
IN 5 IN 05
IN 6 IN 06
IN 7 IN 07
IN 8 IN 10
IN 9 IN 11
IN 10 IN 12
IN 11 IN 13
IN 12 IN 14
IN 13 IN 15
IN 14 IN 16
IN 15 IN 17
+V 1746-IG16 +V
+V +V
IN 0 IN 00
IN 1 IN 01
IN 2 IN 02
IN 3 IN 03
IN 4 IN 04
IN 5 IN 05
IN 6 IN 06
IN 7 IN 07
IN 8 IN 10
IN 9 IN 11
IN 10 IN 12
IN 11 IN 13
IN 12 IN 14
IN 13 IN 15
IN 14 IN 16
IN 15 IN 17
1746-IV16, ITV16
IN 0 IN 00
IN 1 IN 01
IN 2 IN 02
IN 3 IN 03
IN 4 IN 04
IN 5 IN 05
IN 6 IN 06
IN 7 IN 07
IN 8 IN 10
IN 9 IN 11
IN 10 IN 12
IN 11 IN 13
IN 12 IN 14
IN 13 IN 15
IN 14 IN 16
IN 15 IN 17
+V +V
+V +V
L1 1 L1 1
L1 1 L1 1
OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT 00 01 02 03 04 05 06 07 10 11 12 13 14 15 16 17
L1 2 L1 2
L1 2 L1 2
+V +V
+V +V
OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT COM COM 15 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT COM COM 00 01 02 03 04 05 06 07 10 11 12 13 14 15 16 17
+V1 +V1 OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT +V2 +V2 13 14 15 0 1 2 3 4 5 6 7 8 9 10 11 12 +V1 +V1 OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT +V2 +V2 00 01 02 03 04 05 06 07 10 11 12 13 14 15 16 17
L1 0
OUT 0
L1 1
OUT 1
L1 2
OUT 2
L1 3
OUT 3
OUT 4
L1 4
OUT 5
L1 5
OUT 6
L1 6
OUT 7
L1 7
1756-IA8D, TC-IDX081
L1 0
IN 0
IN 1
IN 2
IN 3
L2 0
L2 0
L2 0
L2 0
L2 1
L2 1
L2 1
L2 1
IN 4
IN 5
IN 6
IN 7
L1 1
L2 1
L2 0
L2 0
IN 0
IN 1
IN 2
IN 3
IN 4
IN 5
IN 6
IN 7
IN 8
IN 9
IN 10
IN 11
IN 12
IN 13
IN 14
IN 15
L2 1
L2 1
GND GND 0 0
IN 0
IN 1
IN 2
IN 3
IN 4
IN 5
IN 6
IN 7
IN 8
IN 9
IN 10
IN 11
IN 12
IN 13
IN 14
IN 15
GND GND 1 1
L1 0
L1 0
L1 0
L1 0
L1 0
L1 1
L1 1
L1 1
L1 1
L1 1
177
Part 2 of Adhesive Label Card for Catalog Numbers 1492-IFM20F, -IFM20D24, and -IFM20D120
L2 0
L1 0
L1 0
L1 0
L1 0
L1 1
L1 1
L1 1
L1 1
L2 1
L1 1
1756-OA16, TC-ODA161
L1 0
L2 0
OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
L1 1
L2 1
+DC OUT OUT OUT OUT RTN +DC +DC +DC RTN +DC +DC +DC +DC OUT OUT OUT OUT RTN RTN 0 0 1 2 3 0 0 0 0 0 1 1 1 1 4 5 6 7 1 1
+DC RTN OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT +DC RTN 0 1 2 3 4 5 6 7 8 9 10 0 0 11 12 13 14 15 1 1 IN L2 IN L2 IN L2 IN L2 IN L2 IN L2 IN L2 IN L2 0 0 1 1 2 2 3 3 4 4 5 5 6 6 7 7 1769-IA16 IN IN IN IN IN IN IN IN IN IN IN IN IN IN IN IN L2 L2 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 L2 L2 1769-IM12 IN IN IN IN IN IN IN IN IN IN IN IN L2 L2 0 1 2 3 4 5 6 7 8 9 10 11 1769-IQ16 SINK IN IN IN IN IN IN IN IN IN IN IN IN IN IN IN COM COM COM COM IN 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 1 1 2 2 1769-IQ16 SOURCE +VDC +VDC IN IN IN IN IN IN IN IN IN +VDC +VDC IN IN IN IN IN IN IN 1 1 2 2 8 9 10 11 12 13 14 15 0 1 2 3 4 5 6 7
L1 1 +VDC 1
OUT 0 OUT 0
OUT 1 OUT 1
OUT 2 OUT 2
OUT 5 OUT 5
OUT 6 OUT 6
OUT 7 OUT 7
L1 L1 2 2 +VDC +VDC 2 2
1771-IAD (AC), IND (AC) 1771-IMD (AC) 1771-IAD (DC), IND (DC) 1771-IMD (DC) 1771-IBD, ICD
L1
+V
IN 00 IN 00 IN 00 IN 00 IN 00
IN 01 IN 01 IN 01 IN 01 IN 01
IN 02 IN 02 IN 02 IN 02 IN 02
IN 03 IN 03 IN 03 IN 03 IN 03
IN 04 IN 04 IN 04 IN 04 IN 04
IN 05 IN 05 IN 05 IN 05 IN 05
IN 06 IN 06 IN 06 IN 06 IN 06
IN 07 IN 07 IN 07 IN 07 IN 07
IN 10 IN 10 IN 10 IN 10 IN 10
IN 11 IN 11 IN 11 IN 11 IN 11
IN 12 IN 12 IN 12 IN 12 IN 12
IN 13 IN 13 IN 13 IN 13 IN 13
IN 14 IN 14 IN 14 IN 14 IN 14
IN 15 IN 15 IN 15 IN 15 IN 15
IN 16 IN 16 IN 16 IN 16 IN 16
IN 17 IN 17 IN 17 IN 17 IN 17
1771-IGD
+V
+V
IN 00
IN 01
IN 02
IN 03
IN 04
IN 05
IN 06
IN 07
IN 10
IN 11
IN 12
IN 13
IN 14
IN 15
IN 16
IN 17
+V COM
L1
L1
OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT 00 01 02 03 04 05 06 07 10 11 12 13 14 15 16 17
L1
L2
1771-OBD, OGD
+V
+V
OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT OUT 00 01 02 03 04 05 06 07 10 11 12 13 14 15 16 17
+V COM
3 00 1
4 01 2
5 02 3
6 03 4
7 04 5
8 05 6
9 06 7
10 07 8
11 10 9
12 11 10
13 12 11
14 13 12
15 14 13
16 15 14
17 16 15
18 17 16
19
20
43006-253-01 (12)
178
Accessories
179
Accessories, Continued
Replacement Relays
The relays in the Relay Master and Relay Expander modules are replaceable. The following replacement relays must be used:
Replacement Relays XIM Catalog Number 1492-XIM4024-16R, -16RF 1492-XIM4024-8R 1492-XIM2024-8R, -16R 1492-XIM20120-8R, -16R, -16RF 1492-XIM24-8R, -16RF 1492-XIM120-8R Flexible Relay Module Expansion Cable Replacement Part Catalog Number 700-HK36Z24 700-HK36Z24 700-HK36Z24 700-HK36A1 700-HK36Z24 700-HK36A1 W22101-06-101
180
Accessories, Continued
Wiring diagrams are provided on-line if you require additional information to wire your field device to the terminals of the IFM, XIM or AIFM wiring system modules. Visit the following web site for I/O wiring diagrams of the Interface Modules and cables: 1. http://www.ab.com/raise 2. Type in the catalog number of the IFM/XIM or AIFM you are interested in. Click on Submit. 3. Click on the Modify key (lower left). 4. Click on the areas that indicate NO SELECTION and enter your information (e.g, I/O Platform, I/O Module, etc.). 5. To obtain the wiring diagram, be sure to select the Pre-Wired Cable Connector selection. 6. Configure the 1492 cable for your application by filling in the NO SELECTION areas. 7. Click on the Accept key for the 1492 cable. 8. Click on the Accept key for the 1492 wiring system module (E.g., 1492IFM20F). 9. The configuration results page is displayed. In the selected components table column Supplementary Documents, click on the Wiring Diagram for the I/O Module to IFM.
181
Quick Reference
Digital IFM Specifications
Digital IFM Catalog Number 1492-IFM20F, -RIFM20F 1492-IFM20FN, -RIFM20FN 1492-IFM20F-2, -RIFM20F-2 1492-IFM20F-3 1492-IFM20D24 1492-IFM20D24N 1492-IFM20D24-2 1492-IFM20D24A-2 1492-IFM20DS24-4 1492-IFM20D24-3 1492-IFM20D120 1492-IFM20D120N 1492-IFM20D120-2 1492-IFM20D120A-2 1492-IFM20DS120-4 1492-IFM20D240-2 1492-IFM20D240A-2 1492-IFM20F-F-2, -RIFM20F-F-2 1492-IFM20F-F24-2, -RIFM20F-F24-2 1492-IFM20F-F24A-2, -RIFM20F-F24A-2 1492-IFM20F-F120-2, -RIFM20F-F120-2 1492-IFM20F-F120A-2, -RIFM20F-F120A-2 1492-IFM20F-F240-2 1492-IFM20F-FS-2 1492-IFM20F-FS24-2 1492-IFM20F-FS24A-4 1492-IFM20F-FS120-2 1492-IFM20F-FS120-4 1492-IFM20F-FS120A-4 1492-IFM20F-FS240-4 1492-IFM40F, -RIFM40F 1492-IFM40F-2 1492-RIFM40F-2 1492-IFM40F-3 1492-IFM40D24, -RIFM40D24 1492-IFM40D24-2 1492-IFM40D24A-2 1492-RIFM40D24A-2 1492-IFM40DS24-4 1492-IFM40DS24A-4 1492-IFM40D24-3 1492-IFM40D120-2 1492-IFM40D120A-2 1492-IFM40DS120-4 1492-IFM40DS120A-4 1492-IFM40DS240A-4 1492-IFM40F-F-2 1492-IFM40F-F24-2 1492-RIFM40F-F24-2 1492-IFM40F-F24D-2 1492-IFM40F-F24AD-4 1492-IFM40F-F120-2 1492-IFM40F-FS-2 1492-IFM40F-FS24-2 1492-IFM40F-FS24-4 1492-IFM40F-FS120-2, -RIFM40F-FS120-2 1492-IFM40F-FS120-4 1492-RIFM40F-FS120-4 1492-IFM40F-FS240-4 Voltage Range 0264V AC/DC 0132V AC/DC 0264V AC/DC 0132V AC/DC 1030V AC/DC 1030V AC/DC 1030V AC/DC 1030V AC/DC 1060V AC/DC 1030V AC/DC 85132V AC/DC 85132V AC 85132V AC 85132V AC 85132V AC 204264V AC 204264V AC 0132V AC/DC 1030V AC/DC 1030V AC/DC 85132V AC/DC 85132V AC/DC 204264V AC/DC 0132V AC/DC 1030V AC/DC 1030V AC/DC 85132V AC/DC 85132V AC/DC 85132V AC/DC 204264V AC/DC 0132V AC/DC 0132V AC/DC 0132V AC/DC 060V AC/DC 1030V AC/DC 1030V AC/DC 1030V AC/DC 1030V AC/DC 1060V AC/DC 1030V AC/DC 1030V AC/DC 85132V AC 85132V AC 85132V AC 85132V AC 204264V AC 0132V AC/DC 1030V AC/DC 1030V AC/DC 1030V DC 1030V DC 85132V AC/DC 0132V AC/DC 1030V AC/DC 1030V AC/DC 85132V AC/DC 85132V AC/DC 8530V AC/DC 204264V AC/DC Max. Current (Per Circuit) 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A 2A Max. Current (Per Module) 12 A 12 A 12 A 12 A 12 A 12 A 12 A 12 A 12 A 12 A 12 A 12 A 12 A 12 A 12 A 12 A 12 A 12 A 12 A 12 A 12 A 12 A 12 A 12 A 12 A 12 A 12 A 12 A 12 A 12 A 12 A 12 A 12A 12 A 12 A 12 A 12 A 12A 12 A 12 A 12 A 12 A 12 A 12 A 12 A 12 A 12 A 12 A 12A 8A 8A 12 A 12 A 12 A 12 A 12 A 12 A 12A 12 A Dimensions (L x W x H) (in.) 4.33 x 3.27 x 2.78 2.36 x 3.27 x 2.78 4.33 x 3.27 x 2.78 4.33 x 3.27 x 2.78 4.33 x 3.27 x 2.78 2.36 x 3.27 x 2.78 4.33 x 3.27 x 2.78 4.33 x 3.27 x 2.78 4.33 x 3.27 x 2.78 4.33 x 3.27 x 2.78 4.33 x 3.27 x 2.78 2.36 x 3.27 x 2.78 4.33 x 3.27 x 2.78 4.33 x 3.27 x 2.78 4.33 x 3.27 x 2.78 4.33 x 3.27 x 2.78 4.33 x 3.27 x 2.78 4.33 x 3.27 x 2.78 4.33 x 3.27 x 2.78 4.33 x 3.27 x 2.78 4.33 x 3.27 x 2.78 4.33 x 3.27 x 2.78 4.72 x 3.27 x 2.78 2.36 x 3.27 x 2.78 2.36 x 3.27 x 2.78 3.15 x 3.27 x 2.78 2.36 x 3.27 x 2.78 4.33 x 3.27 x 2.78 3.15 x 3.27 x 2.78 4.33 x 3.27 x 2.78 4.33 x 3.27 x 2.78 8.27 x 3.27 x 2.78 8.27 x 3.27 x 2.78 8.27 x 3.27 x 2.78 4.33 x 3.27 x 2.78 8.27 x 3.27 x 2.78 8.27 x 3.27 x 2.78 8.27 x 3.27 x 2.78 6.69 x 3.27 x 2.78 6.69 x 3.27 x 2.78 8.27 x 3.27 x 2.78 8.27 x 3.27 x 2.78 8.27 x 3.27 x 2.78 6.69 x 3.27 x 2.78 6.69 x 3.27 x 2.78 6.69 x 3.27 x 2.78 8.27 x 3.27 x 2.78 8.27 x 3.27 x 2.78 8.27 x 3.27 x 2.78 4.72 x 3.27 x 2.78 7.09 x 3.27 x 2.78 8.27 x 3.27 x 2.78 4.72 x 3.27 x 2.78 4.72 x 3.27 x 2.78 7.09 x 3.27 x 2.78 4.72 x 3.27 x 2.78 7.09 x 3.27 x 2.78 7.09 x 3.27 x 2.78 7.09 x 3.27 x 2.78 Indicator Circuit Current (Nominal) 2 mA 2 mA 2 mA 2 mA 1.6 mA 2 mA 2.5 mA 2.5 mA 2.5 mA 2.5 mA 2.6 mA 2.5 mA 2.5 mA 2 mA 2.4 mA 2.5 mA 1.2 mA 1.2 mA 2 mA 2.4 mA 2.5 mA 1.2 mA 2.2 mA 1.2 mA Label Card Replacement Part Catalog Number 43006-253-01 44006-274-02, 45006-236-01 43006-253-03, 45006-237-01 45006-077-01 43006-253-01 44006-274-02, 45006-236-01 43006-253-03, 45006-237-01 45006-086-01 45006-056-01 43006-253-04 43006-253-01 44006-274-02, 45006-236-01 43006-253-03, 45006-237-01 45006-086-01 45006-056-01 43006-253-03 45006-086-01 43006-253-03, 45006-237-01 43006-253-03, 45006-237-01 45006-100-01 43006-253-03, 45006-237-01 45006-100-01 45006-110-01 45006-022-01 45006-022-01 45006-120-01 45006-022-01 45006-110-01 45006-120-01 45006-110-01 43006-253-02 43006-253-05/06 46006-114-01, 46006-115-01 43006-253-04 43006-253-02 43006-253-05/06 43006-253-05/06 46006-114-01, 46006-115-01 45006-054-01 45006-054-01 43006-253-04 43006-253-05/06 43006-253-05/06 45006-054-01 45006-054-01 45006-054-01 43006-253-05/06 43006-253-05/06 46006-114-01, 46006-115-01 45006-020-01 45006-047-01 43006-253-05/06 45006-020-01 45006-020-01 45006-047-02 45006-020-01 45006-047-01 46006-116-01 45006-047-02
2 mA 2 mA 2 mA 2 mA 4.1 mA 4.1 mA 2 mA 2.5 mA 2.5 mA 2.6 mA 2.6 mA 2.6 mA 2 mA 2 mA <0.05 mA <0.05 mA 2.5 mA 2 mA 2.4 mA 2.5 mA 1.4 mA 1.4 mA 2.4 mA
182
183
Max. Current (Per Circuit/ Per Pair) 10/12 A 10/12 A 10/12 A 10/12 A 10/12 A 10/12 A 10/12 A 10/12 A 10/12 A 10/12 A 10/12 A 2/NA A 2/NA A 2/NA A 10/12 A
Max. Current Dimensions (Per Module) (L x W x H) (in.) 48 A 48 A 48 A 48 A 48 A 48 A 48 A 48 A 48 A 48 A 48 A 4A 4A 4A 48 A 9.06 x 3.27 x 2.78 6.30 x 3.27 x 2.78 6.30 x 3.27 x 2.78 6.30 x 3.27 x 2.78 6.30 x 3.27 x 2.78 6.30 x 3.27 x 2.78 10.65 x 3.27 x 2.78 10.65 x 3.27 x 2.78 10.65 x 3.27 x 2.78 10.65 x 3.27 x 2.78 11.05 x 3.27 x 2.78 3.15 x 3.27 x 2.19 3.15 x 3.27 x 2.28 3.15 x 3.27 x 2.28 11.05 x 3.27 x 2.78
Label Card Replacement Part Catalog Number 45006-254-01 45006-142-01 45006-142-01 45006-142-01 45006-143-01 45006-143-01 45006-366-01 45006-366-01 45006-366-01 45006-366-01 45006-366-01 45006-144-01 45006-144-01 45006-144-01 45006-366-01
184
1764-28BXB Base Unit Output Current Ratings when using 1492-IFM20x Modules IFM Cat. Number Voltage Range 1764-2BXB Max. Max. Current per Current/Output using IFM IFM Module (Out 0-Out 1) 2 AMP (Out 8-Out 11) 1 AMP (Out 2-Out 7) 0.5 AMP (Out 0-Out 1) 2 AMP (Out 8-Out 11) 1 AMP (Out 2-Out 7) 0.5 AMP (Out 0-Out 1) 2 AMP (Out 8-Out 11) 1 AMP (Out 2-Out 7) 0.5 AMP 12 Amps NA 0C to 60C 12 Amps NA 0C to 60C 12 Amps NA 0C to 60C IFM Module Indicator Circuit Current Operating Ambient Temperature
0264V AC 1492-IFM20F 10125V DC 24V DC 0132V AC 1492-IFM20FN 10125V DC 24V DC 0264V AC 1492-IFM20F-2 10125V DC 24V DC
Note: For inputs use standard 2 A/circuit ratings
1762-L40AWA and -L40BWA Base Unit Output Current Ratings when using 1492-IFM40x Module IFM Cat. Number Voltage Range 1762-L40AWA & Max. Current per -L40BWA max. IFM Module Current/Output using IFM (Out 0-Out 3) 2 Amps (Out 4-Out 15) 1 Amps (Out 0-Out 3) 2 Amps (Out 4-Out 15) 1 Amps 12 Amps 12 Amps IFM Module Indicator Circuit Current NA NA Operating Ambient Temperature 0C to 60C 0C to 60C
1492-IFM40F 1492-IFM40F-2
185
(Out 0,1,10,11) 2 AMP (Out 12-Out 15) 1 AMP (Out 2-Out 9) 0.5 AMP (Out 0,1,10,11) 2 AMP (Out 12-Out 15) 1 AMP (Out 2-Out 9) 0.5 AMP 12 Amps NA 0C to 60C 12 Amps 0C to 60C
186
#20 3
#18 3
#16 2
#14 1
#12 1
15 ms Max.
1800/hr
Maximum number of the same gauge stranded copper conductors allowed per wire funnel. Pollution Degree 2 is an environment where normally only non-conductive pollution occurs, except for occasional temporary conductivity caused by condensation shall be expected. For transients >600V, use a UL recognized suppression device rated at 2.5 kV withstand. Refer to Maximum Relay Contact Switching Capacity Chart below. Maximum continuous current for two adjacent relays is 12 A.
187
50
AC resistive load
10 5 AC inductive load (p.f. =0.4)
1 0.5
10
50
100
500
188
Notes:
189
Notes:
Copyright 2005 Rockwell Automation, Inc. All Rights Reserved. Printed in USA.