Made in the U.S.A.

Inverter Drive® and

Vector Drive® Motors
 Baldor Inverter Drive® and
Vector Drive® Motors are
proven in today’s tough
adjustable speed
applications.

40 HP, 1800 RPM, 30 min duty, TENV Vector Drive Motor. Barge towing winch is
installed on a Mississippi River Lock and Dam.

Baldor Adjustable Speed Drive Motors are proven in many tough applications found in today’s
industrial environment. Premium efficiency designs increase energy savings, lower temperature
rise, and increase motor life. Baldor’s integral horsepower motor designs feature cast iron
construction for extra durability. The use of Baldor’s ISR Inverter Spike Resistant® Magnet Wire,
Class H insulation with Class F (or lower) temperature rise, increases motor life. Totally Enclosed
Non-Ventilated (TENV) and Totally Enclosed Blower Cooled (TEBC) motors are designed and
tested for use on adjustable speed controls to ensure maximum performance and adequate
cooling over the motor’s entire speed range. Baldor Inverter Drive® and Vector Drive® motors meet
NEMA MG1-1993, Part 31 requirements.
Baldor also offers a wide range of Explosion-Proof Inverter Drive® Motors, approved for use in
hazardous locations with Baldor Series 15H Inverters, as well as inverters manufactured by other
companies.

Encoder mount with easy

access for coupling; and bolt CATALOG # ZDM2334T
isolators for electrical isolation 20HP, 1780 RPM
H-25 1024ppr,
industrial encoder Encoder coupling
Heavy gauge steel Cast iron endplate Low loss Grease fitting
blower housing lamination
Mounting Lifting eye Cast iron
Fan guard brackets ribbed frame Cast iron
NEMA C face
Two N.C. thermal
protectors
Bearing
retainer

230/460V, 60Hz.
3 phase blower

Precision balance
for high speed Locked
MS3112E12-10P Dual hole foot Lub-Lok®
Oversized, diagonally split, mounting bearing
receptacle seal
cast iron conduit box

ISR Inverter Spike Resistant® Wire

Class H insulation with 200°C moisture resistant

2
Adjustable Speed A.C. Three Phase
Inverter Drive® and Vector Drive® Motors (Non-Explosion-Proof)

Mechanical Design Characteristics

Frames
143TC- 254TC- 404TC- 5007L-
Specification Description 56C 215TC 365TC 447TC 449TC 5009L
Bearing Retention Locked bearings for universal mounting ● ● ● ● ● ●
Premium grade, single shielded ● ●
Bearings
Premium grade, open with Lube Lock® ● ● ● ●
115V, 1 phase blower (230/460 and all 575 volt ratings) thru 184TC O O O O
Blower 230/460V, 3 phase blower (230/460 volt ratings) ● 215TC ● ● O O
Conduit Box Diagonally split, 360° rotatable in 90° increments. ● ● ● ● ●
Gasketed lid and gasket between box and frame
Drain Holes Prevents moisture build up from condensation ● ●
Drain Plugs One way drain and breather located at the lowest point
● ● ● ●
when motor is mounted horizontally
Drive End C-Face for mounting flexibility on NEMA TC frames ● ● ●① ●① ●① O
Enclosure TENV does not require blower cooling ● ● thru 256TC
TEBC for continuous torque in standard frame ● ● ● ● ●
Aluminum with steel bearing journal ③ ● ●
Endplates
Cast iron - rugged and durable ● ● ● ● ●
Steel band ③ ● thru 145TC
Frame
Cast iron ● ● ● ● ●
Foot Mounting Rigid base, dual hole foot pattern for mounting flexibility ● ● ● ●
Ground Screw Inside terminal box for convenience ● ● ● ● ● ●
Lifting Provisions Shouldered eyebolt ● ● ●② ●② ●②
Lubricant Chevron SRI or equivalent ● ● ● ● ● ●
Mounting Inverter motors are machined for mounting a Baldor
(Encoder) encoder kit. ● ● ● ● ● ●
Nameplate Includes base volts and frequency, connection diagram,
blower rating (volts, hertz, phase and amps), maximum ● ● ● ● ● ●
motor speed, rotor inertia and magnetization current
Regreasing Regreasable without removing blower housing ● ● ● ● ●
Rotor Special high pressure aluminum die cast with low
● ● ● ● ●
Construction loss electrical steel and special slot configuration
C1035 steel ● ●
Shaft Material
C1137 steel ● ●
C1045 Steel ● ●

Encoder Feedback For Vector Drive® Motor Only

Code Incremental ● ● ● ● ● ●
Connection M.S. connector (plug and receptacle supplied) ● ● ● ● ● ●
Encoder H25, F-1, Face Mounted ● ● ● ● ● ●
Encoder Bearings ABEC-7 ● ● ● ● ● ●
Frequency 100 Kilohertz standard
● ● ● ● ● ●
Response
Isolation Encoder electrically isolated from motor to prevent
● ● ● ● ● ●
motor noise interference
Pulse per 1024 standard ● ● ● ● ● ●
revolution
Signal Dual quadrature channels with index and compliments ● ● ● ● ● ●
Voltage 5-15 VDC Standard ● ● ● ● ● ●
① NEMA TS frames do not include drive end c-face.
② 449T, 5007L, 5009L Lifting eyes are integrally cast into stator frame.
③ Fractional horsepower and washdown duty motors only.
● = Standard, O = Optional
3
Industrial quality Baldor
Inverter Drive® and
Vector Drive® Motors are
in stock thru 500 Hp and
ready for immediate
shipment.

15Hp Vector Drive powering a turning lathe.

Baldor’s broad line of adjustable speed A.C. motors are stocked in over 40 world-wide
warehouses and in our Fort Smith distribution center. Same day shipping is available on both
Inverter Drive® and Vector Drive® Motors, as well as over 4800 other products. For motors or
drives, Baldor products are the best value.

Electrical Design Characteristics

Frames
56C- 182TC- 254TC- 404TC- 447TC- 5007L-
Specification Description 145TC 215TC 365TC 447TC 449TC 5009L
Duty Continuous ● ● ● ● ● ●
Insulation Class H - Meets NEMA MG1-1993, Part 31 ● ● ● ● ● ●
ISR® 200°C moisture resistant, ● ● ● ● ● ●
Magnet Wire Inverter Spike Resistant® Wire
Laminations Low loss electrical grade steel ● ● ● ● ● ●
Lead Wire Non-wicking, cross-link-polyethylene ● ● ● ●
Phase Insulation Nomex, minimum 14 mils ● ● ● ● ● ●
Ratings NEMA Design B ● ● ● ● ● ●
Rise Class F ● ● ● ● ● ●
Slot Cell
Slot Separator Nomex ● ● ● ● ● ●
Slot Wedge
Thermal Quantity 2, normally closed 155°C, ● ● ● ● ● ●
Sensor (Class F) bi-metallic thermostat
Varnish Double dip & bake, polyester phenolic Class H ● ● ● ● VPI VPI
230 / 460V @ 60 Hertz ● ● ●
Voltage 460 V @ 60 Hertz ● ● ● ● ● ●
575 V @ 60 Hertz ● ● ● O O O
Optional 50 hertz voltages available O O O O O O
●= Standard
O= Optional

4
ISR Inverter Spike Resistant® Wire
All 200, 230, 460, 575 and 220/380/415 - 50 hertz three phase Baldor AC motors from 1HP to 800
HP are wound with ISR Inverter Spike Resistant® magnet wire. This includes the following Baldor
motor families.

• Super-E® Premium Efficient • Standard-E™ • Inverter Drive®

• Chemical Processing (Complies with EPAct) • Pump
• AC Induction Servo Motors • Washdown Duty® • Dirty Duty®
• Explosion-Proof • Vector Drive®

Baldor motors wound with ISR® wire are up to 100 times more resistant to transient spikes, high
frequencies, and short rise time pulses produced by inverters and vector drives. The result is a
better motor with longer life, reduced downtime and better overall value.

Baldor is the first motor manufacturer to use this new wire in such a wide range of motors, just
like we were the first to use type-MR moisture resistant wire across our entire line over 10 years
ago.

The use of variable speed controls with AC induction motors is growing rapidly. Even if the motor
you’re buying today is not used with a variable speed control, there is a chance that a control
may be added later. Why not plan for the future and buy the best motor that you can today - a
Baldor motor wound with ISR Inverter Spike Resistant® wire.

Baldor Inverter Drive® and Vector Drive® motors are designed to be used as defined by NEMA
MG-1-1993, Part 31.

ISR Inverter Spike Resistant® test results:

Up to 100 times more resistant to transient spikes, high frequencies, and short rise-time pulses
produced by inverters.

PULSE ENDURANCE TEST

1000

Technical Specifications:
NEMA MW-35

Pulse Endurance
100 Test Conditions:
Twisted pairs @ 20,000 Hz,
2 kV, 0.025 microsecond
risetime, 50% duty cycle, 90°C

Pulse Endurance Index =

Life of Product/Life of 18 H
MW-35 (Reference)
Index

10 Thermal Properties, Chemical

Resistance and Dielectric
Strength:
ISR™ Wire is equal to or better
than MR wire.

Thermal Rating: 200°C

1 Source:
Phelps Dodge Magnet Wire
Company (Used with permission)

0.1
Moisture Resistant "Triple-Build" ISR™ Wire
MR Wire Wire

5
Baldor’s broad line of adjustable
speed A.C. Inverter Drive® Motors
include TENV and TEBC
enclosures. Applications include
conveyors, pumps, fans, and
material handling equipment not
requiring full torque at low or zero
speed.

Inverter Drive® and Vector Drive® Motors

Performance Data 230/460 Volt Ratings
60HZ INVERTER VECTOR 460 VOLT OUTPUT TORQUE % APPROX.
BASE MAX. NEMA CATALOG CATALOG LINE AMPS LB-FT EFFICIENCY WK2 WEIGHT BEARINGS
HP kW SPEED SPEED FRAME ENCL. NO. NO. IDLE F.L. F.L. L.R. B.D. LINE POWER LB-FT2 LBS DE ODE
0.33 0.25 1725 6000 56C TENV IDNM3534 - 0.45 0.55 1.0 3.4 3.8 76.0 0.771 29 6205 6203
0.50 0.37 1725 6000 56C TENV IDNM3538 - 0.50 0.8 1.5 5.2 6.5 75.5 0.949 32 6205 6203
0.75 0.56 1725 6000 56C TENV IDNM3542 - 0.65 1.1 2.3 6.5 8.3 80.0 0.119 36 6205 6203
1.0 0.75 1725 6000 143TC TENV IDNM3581T ZDNM3581T 0.92 1.6 3.0 12.0 15.0 81.5 0.142 53 6205 6203
1.0 0.75 1725 6000 143TC TEBC IDM3581T ZDM3581T 0.81 1.4 3.0 10.0 14.5 85.5 0.142 54 6205 6203
1.0 0.75 1150 4000 145TC TEBC IDM3582T ZDM3582T 1.08 1.7 4.5 14.0 15.5 82.5 0.17 67 6205 6203
1.5 1.1 1725 6000 145TC TENV IDNM3584T ZDNM3584T 1.05 2.1 4.5 14.0 17.0 82.5 0.19 62 6205 6203
1.5 1.1 1725 6000 143TC TEBC IDM3584T ZDM3584T 1.16 2.1 4.5 14.0 22.0 87.5 0.12 58 6205 6203
1.5 1.1 1160 4000 182TC TEBC IDM3667T ZDM3667T 1.8 2.6 6.8 12.0 18.5 86.5 0.3 98 6206 6205
2.0 1.5 1725 6000 182TC TENV IDNM3669T ZDNM3669T 1.7 2.9 6.0 25.0 30.0 84.0 0.263 95 6206 6205
2.0 1.5 1725 6000 145TC TEBC IDM3587T ZDM3587T 1.2 2.5 6.0 21.0 24.0 86.5 0.208 66 6205 6203
2.0 1.5 1160 4000 184TC TEBC IDM3664T ZDM3664T 2.5 3.6 9.0 15.4 29.0 87.5 0.38 115 6206 6205
3.0 2.2 1750 3600 184TC TENV IDNM3661T ZDNM3661T 2.0 4.0 9.0 22.9 37.1 88.5 0.319 108 6206 6205
3.0 2.2 1760 6000 182TC TEBC IDM3661T ZDM3661T 2.2 4.0 9.0 22.0 31.0 89.5 0.26 98 6206 6205
3.0 2.2 1160 4000 213TC TEBC IDM3764T ZDM3764T 3.4 5.0 13.5 28.0 49.0 88.5 0.734 172 6307 6206
5.0 3.7 1750 6000 213TC TENV IDNM3767T ZDNM3767T 3.4 6.7 14.9 48.0 52.0 89.5 0.734 166 6307 6206
5.0 3.7 1760 6000 184TC TEBC IDM3665T ZDM3665T 3.4 6.5 15.0 32.0 50.0 90.2 0.38 115 6206 6205
5.0 3.7 1160 6000 215TC TEBC IDM3768T ZDM3768T 4.8 7.7 22.5 42.0 65.0 89.5 1.05 200 6307 6206
7.5 5.6 1760 6000 254TC TENV IDNM2237T ZDNM2237T 5.3 10 22.2 63.0 85.0 89.5 1.4 238 6309 6208
7.5 5.6 1760 6000 213TC TEBC IDM3770T ZDM3770T 4.6 9.8 22.5 45.0 72.0 91.0 0.734 176 6307 6206
7.5 5.6 1180 4000 254TC TEBC IDM2276T ZDM2276T 5.2 10.6 33.3 96.0 115 89.5 3.7 283 6309 6208
10 7.5 1760 6000 256TC TENV IDNM2238T ZDNM2238T 5.4 12.8 29.7 75.0 110 92.4 2.11 281 6309 6208
10 7.5 1760 6000 215TC TEBC IDM3774T ZDM3774T 5.0 12.7 30.0 66.0 99.0 91.7 1.05 196 6307 6206
10 7.5 1180 2400 256TC TEBC IDM2332T ZDM2332T 6.65 13.9 44.5 114 123 89.5 4.18 303 6309 6208
15 11.2 1765 4000 254TC TEBC IDM2333T ZDM2333T 6.95 18.0 45.0 88.0 143 92.4 1.84 280 6309 6208
15 11.2 1170 2400 284TC TEBC IDM4100T ZDM4100T 7.4 19.5 67.0 160 167 91.0 6.16 422 6311 6309

Continued on next page...

6
 Baldor’s A.C. Vector Drive® Motor
applications include test stands,
material handling and packaging
equipment, and printing presses.
For adjustable base speed
operation with full torque from
zero to base speed and constant
horsepower to maximum speed.
Available from 1 to 500
horsepower.

Inverter Drive® and Vector Drive® Motors

Performance Data 230/460 Volt Ratings
60 HZ INVERTER VECTOR 460 VOLT OUTPUT TORQUE % APPROX.
BASE MAX. NEMA CATALOG CATALOG LINE AMPS LB-FT EFFICIENCY WK2 WEIGHT BEARINGS
HP kW SPEED SPEED FRAME ENCL. NO. NO. IDLE F.L. F.L. L.R. B.D. LINE POWER LB-FT2 LBS DE ODE
20 14.9 1765 4000 256TC TEBC IDM2334T ZDM2334T 8.5 24.0 60.0 120 183 93.0 2.27 303 6309 6208
20 14.9 1170 3600 286TC TEBC IDM4102T ZDM4102T 9.4 26.0 90.0 216 216 91.7 7.39 451 6311 6309
25 18.7 1780 4000 284TC TEBC IDM4103T ZDM4103T 11.9 30.5 45.0 137 226 93.6 3.98 446 6311 6309
25 18.7 1180 2400 324TC TEBC IDM4111T ZDM4111T 13.27 31.0 111 328 356 93.0 11.52 482 6312 6311
30 22.4 1780 4000 286TC TEBC IDM4104T ZDM4104T 14.5 34.0 90.0 143 256 94.1 4.46 437 6311 6309
30 22.4 1180 3600 326TC TEBC IDM4117T ZDM4117T 14.93 37.0 133 395 430 93.0 12.67 630 6312 6311
40 30 1780 4000 324TC TEBC IDM4110T ZDM4110T 18.9 48.0 118 283 354 94.5 8.57 633 6312 6311
40 30 1185 3600 364TC TEBC IDM4308T ZDM4308T 19.14 49.0 177 270 520 94.1 18.2 767 6313 6312
50 37 1780 4000 326TC TEBC IDM4115T ZDM4115T 22.9 59 148 367 450 94.5 9.64 700 6312 6311
50 37 1185 3600 365TC TEBC IDM4312T ZDM4312T 24.0 61.0 221 379 700 94.1 21.1 816 6313 6312
60 45 1780 3600 364TC TEBC IDM4314T ZDM4314T 24.5 69 177 558 637 95.0 13.6 806 6313 6312
60 45 1185 2800 405TC TEBC IDM4403T ZDM4403T 25.59 71 265 465 810 94.5 36 1114 6316 6313
60 45 1180 2800 404TS TEBC IDM4403TS ZDM4403TS 32.0 76 266 410 718 94.1 35.2 1126 6313 6313
75 56 1780 3600 365TC TEBC IDM4316T ZDM4316T 28.6 86 222 607 749 95.0 15 893 6313 6312
75 56 1185 2800 404TC TEBC IDM4404T ZDM4404T 30.85 88 332 600 988 94.5 40 1239 6316 6313
75 56 1180 2800 405TS TEBC IDM4404TS ZDM4404TS 40.0 95 332 498 863 93.6 41 1180 6313 6313
100 75 1780 2800 404TC TEBC IDM4400T-4 ZDM4400T-4 26.5 114 300 600 660 95.0 27 1196 6316 6313
100 75 1180 2200 444TC TEBC IDM4409T-4 ZDM4409T-4 44.0 120 445 528 1200 95.4 58.8 1672 6319 6313
125 93 1780 2200 444TC TEBC IDM4410T-4 ZDM4410T-4 46.3 141 370 615 1075 95.4 45.3 1550 6319 6313
150 112 1780 2200 445TC TEBC IDM4406T-4 ZDM4406T-4 52.0 169 442 660 1300 95.4 52.1 1630 6319 6313
200 149 1780 2200 447TC TEBC IDM4407T-4 ZDM4407T-4 59.8 221 589 714 1467 95.8 63.5 1837 6319 6314
250 187 1780 2400 449TC TEBC IDM4408T-4 ZDM4408T-4 84.9 276 740 832 1774 95.8 76.23 2917 6319 6314
300 224 1785 2400 449TC TEBC IDM44304T-4 ZDM44304T-4 90.2 333 883 1393 2630 95.8 89.68 2345 6319 6314
350 261 1785 2400 449TC TEBC IDM44354T-4 ZDM44354T-4 97.0 388 1032 1640 3450 95.8 84.16 2691 6319 6314
400 298 1785 1800 5007L TEBC IDM50404L-4 ZDM50404L-4 97.0 432 1172 1047 2518 96.2 194 4325 6322 6222
450 336 1790 1800 5007L TEBC IDM50454L-4 ZDM50454L-4 117 492 1320 1221 2988 96.5 209 4789 6322 6222
500 373 1790 1800 5007L TEBC IDM50504L-4 ZDM50504L-4 130 540 1465 1394 3388 96.8 234 4767 6322 6222

7
Inverter Drive® and Vector Drive® Motors
Performance Data 575 Volt Ratings
60 HZ INVERTER VECTOR 575 VOLT OUTPUT TORQUE % APPROX.
BASE MAX. NEMA CATALOG CATALOG LINE AMPS LB-FT EFFICIENCY WK2 WEIGHT BEARINGS
HP kW SPEED SPEED FRAME ENCL. NO. NO. IDLE F.L. F.L. L.R. B.D. LINE POWER LB-FT2 LBS DE ODE
1.0 0.75 1750 6000 143TC TEBC IDM3581T-5 ZDM3581T-5 0.65 1.1 3.0 10.0 14.5 85.5 0.15 64 6205 6203
1.5 1.1 1750 6000 145TC TEBC IDM3584T-5 ZDM3584T-5 0.93 1.7 4.5 14.0 22.0 87.5 0.18 68 6205 6203
2.0 1.5 1750 6000 145TC TEBC IDM3587T-5 ZDM3587T-5 0.96 2.0 6.0 21.0 24.0 86.5 0.21 73 6205 6203
3.0 2.2 1760 6000 182TC TEBC IDM3661T-5 ZDM3661T-5 1.8 3.2 9.0 22.0 31.0 89.5 0.27 98 6206 6205
5.0 3.7 1750 6000 184TC TEBC IDM3665T-5 ZDM3665T-5 2.7 5.2 15.0 32.0 50.0 90.2 0.37 115 6206 6205
7.5 5.6 1760 6000 213TC TEBC IDM3770T-5 ZDM3770T-5 3.9 7.8 22.4 39.0 69.9 90.2 0.85 170 6307 6206
10 7.5 1760 6000 215TC TEBC IDM3774T-5 ZDM3774T-5 4.6 9.9 30.0 93.0 106 91.0 1.2 179 6307 6206
15 11.2 1760 4000 254TC TEBC IDM2333T-5 ZDM2333T-5 5.56 14.5 45.0 88.0 143 92.4 1.84 299 6309 6208
20 14.9 1765 4000 256TC TEBC IDM2334T-5 ZDM2334T-5 6.8 19.3 60.0 120 183 93.0 2.27 298 6309 6208
25 18.7 1780 4000 286TC TEBC IDM4103T-5 ZDM4103T-5 9.55 24.5 74.0 137 226 93.6 3.98 422 6311 6309
30 22.4 1780 4000 286TC TEBC IDM4104T-5 ZDM4104T-5 9.68 29.0 90.0 143 256 94.1 4.46 454 6311 6309
40 30 1780 4000 324TC TEBC IDM4110T-5 ZDM4110T-5 12.3 37.0 120 219 310 94.5 7.76 618 6312 6311
50 37 1780 4000 326TC TEBC IDM4115T-5 ZDM4115T-5 14.0 46.0 150 276 360 94.5 9.7 666 6312 6311
60 45 1780 4000 364TC TEBC IDM4314T-5 ZDM4314T-5 19.2 56.0 178 421 478 94.5 11.7 808 6313 6312
75 56 1780 4000 365TC TEBC IDM4316T-5 ZDM4316T-5 23.2 69.0 221 520 700 95.0 15.3 869 6313 6312
100 75 1780 2800 404TC TEBC IDM4400T-5 ZDM4400T-5 22.8 91.0 300 635 690 95.0 27.2 1172 6316 6313
125 93 1780 2200 444TC TEBC IDM4410T-5 ZDM4410T-5 37.0 113 370 615 1895 95.4 45.4 1505 6314 6319
150 112 1780 2200 445TC TEBC IDM4406T-5 ZDM4406T-5 41.6 135 442 660 1300 95.4 52.1 1659 6314 6319

Custom Inverter Drive® and Vector Drive® Motor Options

Mechanical Characteristics Electrical Characteristics
• NEMA C-Face or D-Flange • Special Voltages
• IEC Metric Foot Mounting • 50 Hertz Designs
B5-Face or B-14 Flange • Special Speeds
• Custom Shaft Extensions • Extended Speed Range
• Space Heaters • Wye/Delta Winding Switching
• Winding RTD’s or Thermistors for Extended Speed Range
• Bearing RTD’s or Thermistors
• Oversize Ball or Roller Bearings
• Shaft Grounding Brush
• Electrically Isolated Bearings

In addition to the Baldor Inverter Drive® and Vector Drive® motors shown in this brochure that are
available from stock, motors are also available as custom for special requirements on OEM
applications. Baldor’s short lead times can supply the motor for your specific application with
special voltage, base speed, Design C torque, extended speed range, C-Face, D-Flange, IEC
metric dimensions, or other application-based needs. Special motors are in use on antenna
positioning drives, automotive dynamometers, centrifuges, spindle-drives, hoists, elevators,
printing presses, pumps, and HVAC equipment.
8
Adjustable Speed A.C. Three Phase
Inverter Drive® and Vector Drive® Washdown Duty Motors

Baldor’s A.C. Inverter Drive® and

Vector Drive® Washdown Duty Motors
range from 1 to 10 horsepower and
are suitable for use on conveyors,
pumps, and other equipment in the
food processing industry. Specifically
designed for high pressure
washdown applications.

Washdown Duty Design Characteristics

Specification Description
Bearings Premium double-sealed ball bearings, lubricated with moisture resistant grease for longer life in wet environments.
Drains Multiple drain hole locations with removable plugs maximize drainage and minimize water entry.
Endplates Die-cast aluminum endplates are standard with an electrostatically applied and baked epoxy finish.
Frame & Base A rolled steel frame and base with a baked-on epoxy finish is standard.
Gaskets Neoprene gaskets prevent entrance of moisture between the conduit box and the motor frame as well as the lid and
conduit box.
Hardware Stainless steel hardware for corrosion protection.
Nameplate Nameplate and fastening pins are stainless steel to prevent rust and corrosion.
Paint FDA approved two part external epoxy finish meets or exceeds food industry sanitary requirements and stands up to
cleaning solutions during washdown periods.
Rotors Rotors on all AC washdown motors are epoxy coated to extend motor life and prevent internal corrosion.
Shaft Entire shaft is made of 300 series stainless steel to prevent rust and corrosion.
Shaft Seals A contact lip seal is provided on the drive-end shaft. A V-ring type Forsheda® rotating seal is provided on the drive-end
shaft preventing entrance of contaminant’s into the bearings.
UL & CSA UL recognized component #E46145, CSA recognized component # LR2262. NEMA MG1-1993, Part 31.

Washdown Duty Performance Data 230/460 Volt Ratings

60 HZ INVERTER VECTOR 460 VOLT OUTPUT TORQUE % APPROX.
BASE MAX. NEMA CATALOG CATALOG LINE AMPS LB-FT EFFICIENCY WK2 WEIGHT BEARINGS
HP kW SPEED SPEED FRAME ENCL. NO. NO. IDLE F.L. F.L. L.R. B.D. LINE POWER LB-FT2 LBS DE ODE
1 0.75 1750 6000 143TC TENV IDWNM3546T ZDWNM3546T 0.81 1.4 3.0 10.0 14.5 85.5 0.14 44 6205 6203
1.5 1.1 1750 6000 145TC TENV IDWNM3554T ZDWNM3554T 1.2 2.1 4.5 19.8 20.5 87.5 0.21 49 6205 6203
2 1.5 1725 6000 182TC TENV IDWNM3609T ZDWNM3609T 1.7 2.9 6.0 25.0 30.0 84.0 0.26 68 6206 6205
3 2.2 1750 3600 184TC TENV IDWNM3611T ZDWNM3611T 1.8 4.0 9.0 23.0 33.0 88.5 0.32 81 6206 6205
5 3.7 1760 6000 213TC TENV IDWNM3707T ZDWNM3707T 3.4 6.7 14.9 48.0 52.0 89.5 0.74 124 6307 6206
7.5 5.6 1765 4000 254TC TENV IDWNM22937T ZDWNM22937T 4.0 9.1 22.5 48.6 86.0 91.0 1.75 226 6309 6208
10 7.5 1765 4000 254TC TENV IDWNM22938T ZDWNM22938T 4.4 12.0 30.0 58.0 114 91.7 2.5 291 6309 6208

9
Adjustable Speed A.C.
Three Phase Inverter
Drive® Explosion-Proof
Fan Cooled Motors

Mechanical Design Characteristics

Frames
143TC- 254TC-
Specification Description 56C 215TC 365TC 405T
Bearing Retention Locked bearings for universal mounting ● ● ● ●
Bearings Premium grade, double shielded ● ●
Premium grade, open with Lube Lock® ● ●
Conduit Box & Lid U. L. approved cast iron explosion-proof ● ● ● ●
Drive End C-Face for mounting flexibility on NEMA TC frames ● ● ● ●
Endplates Aluminum with steel bearing journal ● thru145TC
Cast iron - rugged and durable from 182TC ● ●
Explosion-Proof Class I, Group D, Class II, Group F & G. Temp. Rating 160°C ● thru 145TC
Classifications Class I, Group D only. Temperature Rating 280°C from 182TC ● ●
Frame Steel band ● thru 145TC
Cast iron from 182TC ● ●
Foot Mounting Rigid base, dual hole foot pattern for mounting flexibility ● ● ● ●
Ground Screw Inside terminal box for convenience ● ● ● ●
Lifting Provisions Eyebolt ● ● ●
Lubricant Chevron SRI or equivalent ● ● ● ●
Nameplate U.L./CSA listed nameplate. Includes base volts and ● ● ● ●
frequency, connection diagram
Regreasing Regreasable without removing blower housing ● ● ●
Rotor Special high pressure aluminum die cast with low ● ● ● ●
Construction loss electrical steel and special slot configuration
Shaft Material C1035 steel ● ●
C1137 steel ● ●

Electrical Design Characteristics

Frames
143TC- 254TC-
Specification Description 56C 215TC 365TC 405T
Insulation Class F Meets NEMA MG1-1993, Part 31 ● ● ● ●
ISR® 200°C moisture resistant,
Magnet Wire Inverter Spike Resistant® Wire ● ● ● ●
Service Factor 1.00 ● ● ● ●
Voltage 230 / 460V @ 60 Hertz ● ● ● ●

10
A.C. Inverter Drive® Explosion-Proof Fan-Cooled Motors
UL and CSA approved for use in hazardous locations.

Stock Inverter Drive® Explosion-Proof Motor ratings 1/2 through 2 Hp motors are designed for
Class I, Group D; Class II, Group F & G temperature rating T3C (160°C). Motors may be operated
at a 10:1 constant torque or variable torque speed range. Operation above base speed to
maximum speed is constant horsepower.

3 through 75 Hp motors are designed for Class I, Group D temperature code T2A (280°C) only.
Motors may be operated at a 2:1 constant torque or a 10:1 variable torque speed range.
Operation above base speed to maximum speed is constant horsepower.

Performance Data 230/460 Volt Ratings

60 HZ INVERTER 460 VOLT OUTPUT TORQUE MAX % APPROX.
BASE MAX. NEMA CATALOG LINE AMPS LB-FT CONT. EFFICIENCY WK2 WEIGHT BEARINGS
HP kW SPEED SPEED FRAME ENCL. NO. IDLE F.L. F.L. L.R. B.D. RPM LINE LB-FT2 LBS. DE ODE
0.50 0.37 1750 2700 56C TEFC IDXM7006 0.5 0.8 1.5 5.6 6.7 2700 82.5 0.09 45 6205 6203
0.75 0.56 1750 2700 56C TEFC IDXM7010 0.61 1.1 2.25 8.4 8.8 2700 82.5 0.12 49 6205 6203
1 0.75 1750 2700 143TC TEFC IDXM7014T 0.81 1.4 3 10 14.5 2700 85.5 0.142 47 6205 6203
1.5 1.1 1750 2700 145TC TEFC IDXM7034T 1.13 2.1 4.5 19 23 2700 88.5 0.166 53 6205 6203
2 1.5 1750 2700 145TC TEFC IDXM7037T 1.3 2.6 6 25.3 27.4 2700 88.5 0.237 67 6205 6203
3 2.2 1760 2700 182TC TEFC IDXM7142T 2.2 4 9 22 31 2700 89.5 0.26 137 6206 6205
5 3.7 1760 2700 184TC TEFC IDXM7144T 3.4 6.5 15 32 50 2700 89.5 0.4 151 6206 6205
7.5 5.6 1760 2700 213TC TEFC IDXM7147T 4.9 9.7 22.4 42.9 69.9 2700 90.2 0.85 162 6307 6206
10 7.5 1760 2700 215TC TEFC IDXM7170T 5.9 12.5 30 93 106 2700 91.7 1.14 185 6307 6206
15 11.2 1765 3600 254TC TEFC IDXM7054T 6.95 18 45 88 143 3600 92.4 1.84 375 6309 6208
20 14.9 1765 2700 256TC TEFC IDXM7056T 8.5 24 60 120 183 2700 93.0 2.27 393 6309 6208
25 18.7 1780 2400 284TC TEFC IDXM7058T 11.9 30.5 74 137 226 2400 93.6 3.98 494 6311 6309
30 22.4 1780 2700 286TC TEFC IDXM7060T 14.5 34 90 143 256 2700 94.1 4.46 470 6311 6309
40 30.0 1780 2700 324TC TEFC IDXM7062T 15.3 47 118 221 285 2700 94.5 7.5 713 6312 6311
50 37.0 1780 2700 326TC TEFC IDXM7064T 22.9 59 148 367 450 2700 94.5 9.64 782 6312 6311
60 45.0 1780 2700 364TC TEFC IDXM7066T 24.0 71 178 440 500 2700 94.5 11.7 1006 6313 6312
75 56.0 1780 2500 405T TEFC IDXM7068T 25.6 87.3 222 524 510 2500 93.6 22.4 1176 6316 6313

11
Explosion-Proof Inverter Drive® Motor Capabilities
Designed for Class I, Group D temperature Code T2A (280°C) only. Motors may be operated at
10:1 constant torque or variable torque speed range. Operation above base speed to maximum
speed is constant horsepower. 1.0 Service Factor. Thermostat.

NEMA BASE MAX. NEMA BASE MAX. NEMA BASE MAX.

HP FRAME SPEED SPEED HP FRAME SPEED SPEED HP FRAME SPEED SPEED
0.50 56 1750 2700 5 215T 1760 2700 25 324TS 3550 5400
0.75 56 1750 2700 5 245T 1160 1800 25 324T 1780 2700
1 143T 1750 2700 7.5 215T 3525 5400 25 326T 1180 1800
1 145T 1150/ 800 7.5 215T 1760 2700 30 326TS 3550 5400
1.5 143T 3450 5400 7.5 256T 1160 1800 30 326T 1780 2700
1.5 143T 1750 2700 10 254T 3525 5400 30 364T 1180 1800
1.5 184T 1150 1800 10 254T 1760 2700 40 364TS 3550 4500
2 145T 3450 5400 10 284T 1160 1800 40 364T 1780 2700
2 145T 1750 2700 15 256T 3525 5400 40 404T 1180 1800
2 213T 1160 1800 15 256T 1760 2700 50 365TS 3550 4500
3 184T 3450 5400 15 286T 1170 1800 50 365T 1780 2700
3 184T 1750 2700 20 284TS 3525 5400 50 405T 1180 1800
3 215T 1160 1800 20 284T 1765 2700 60 405TS 3550 3600
5 213T 3450 5400 20 324T 1170 1800 60 405T 1780 2500
Note: Nema frame items in color are rated Class I, Group D, Class II, Group F & G, temperature rating T3C (160°C) and are stocked items. Shaded areas are cast iron
frames.

12
Matched Performance™ Curves
Matched Performance™ is Motor: IDM3665T - 5 HP
Baldor’s solution to the concern, Control: ID15H405-E - 5 HP Series 15H Inverter
“What kind of constant torque and
constant horsepower speed range
will I get with this combination of
33.0 11.00
motor and motor control?” Only
30.0 10.00
Baldor provides Matched PEAK TORQUE
Performance™ curves that go 27.0 9.00

beyond the “typical performance” 24.0 8.00

HORSEPOWER • AMPS
curves and instead provides actual 21.0
AMPS
7.00

TORQUE (ft-lbs)
laboratory dynamometer test 18.0 6.00
results. 15.0
TORQUE HP 5.00

12.0 4.00
Each test is performed in Baldor’s
9.0
own engineering testing laboratory 3.00
CONTINUOUS
using advanced dynamometer 6.0
OPERATING AREA 2.00

equipment and digital power 3.0 1.00

RATED
measurements. A typical Matched 0.0
0 400 800 1200 1600 2000 2400 2800 3200 3600
0.00
Performance™ test requires 2-4 SPEED (rpm)
days of continuous testing. This
painstaking effort is another
example of Baldor’s commitment to
providing customers the extra value
to make our products easy to apply
to your specific application needs.

These curves show the continuous

operating constant torque speed
Motor: ZDM2334T - 20 HP
range that can be produced without
exceeding Class F temperature rise Control: ZD18H420-EO - 20 HP Series 18H Vector
in the motor. The lower Class F rise
is selected to provide long life, even
when a Class H insulation system is 180.0 46.27
used in Baldor Inverter Drive® and
160.0 PEAK TORQUE 41.13
Vector Drive® motors.
140.0 35.99

Peak Torque is the maximum

POWER • AMPS
30.85
TORQUE (Nm)

120.0
AMP
amount of torque a Baldor Series 100.0 25.71
15H Inverter, Series 18H or 26M (15 Kw)
80.0 20.57
Vector Drive can produce. This may TORQUE
HP

be limited by the breakdown torque 60.0 15.42

of the motor or the control’s current- 40.0

CONTINUOUS
OPERATING AREA 10.28
limited peak torque. Peak torque is 20.0 5.14
available for momentary overloads RATED
0.0 0.0
or acceleration and deceleration 0 400 800 1200 1600 2000 2400 2800 3200 3600 4000
requirements. SPEED (rpm)

The horsepower curve is simply a

representation of how much power
is available from the motor at any
given operating speed. The
horsepower curve can be used to
size applications requiring constant
horsepower operation.
13
Conduit Box Volumes
MOTOR BALDOR VOLUME NEMA MINIMUM VOLUME NPT HOLE
FRAME SIZE IN3 IN3 SIZE
56C 8.2 7.5 0.875
143TC/145TC 20.6 12 0.75
182TC/184TC 20.6 16 0.75
213TC/215TC 48 26 1
254TC/256TC 48 26 1.25
284TC/286TC 221 26 1.5
324TC/326TC 221 55 2
364TC/365TC 221 100 2
404TC/405TC 388 180 2.5
444TC/445TC 600 600 2.5
445TC/447TC 600 600 2.5
447TC/449TC 1500 840 4
5007L-5009L 2100 1540 4

Conduit Adapter For Blower Leads

Nominal
PART DIMENSIONS
TRADE Mounting UL/CSA
SIZE Hole DESCRIP- A B C
Diameter TION
in. mm. in. mm. in. mm. in. mm.
1/2 0.875 22.2 SP1 0.60 15.2 1.12 28.4 0.28 7.1

Encoder Receptacle Connections

PIN FUNCTION
A A
B B
C Z(C) A
D VDC (5-15 VDC Standard) B
H
E Shield K J

F Circuit Ground G C
E
G Case Ground
F D
H A Compliment (A)
J B Compliment (B)
K Z (C) Compliment (Z or C)
Standard Receptacle MS3112E12-10P (Baldor Part # WD1434)
Standard Plug MS3116J12-10S (Baldor Part # WD1435)
Both receptacle and plug are provided with the motor. Note that together these connections are weatherproof.

14
Connection Diagrams
Main Motor Power Leads
9 Lead
Wye-Connected Motor OPTIONAL T'STATS LOW VOLTAGE HIGH VOLTAGE
1 J
2Y 1Y
4 5 6
4 5 6
4
7 7 8 9 7 8 9
1 2 3 1 2 3

J LINE LINE
6 9 5
8

3 2

9 Lead
Delta-Connected Motor OPTIONAL T'STATS
J LOW VOLTAGE HIGH VOLTAGE
1 2 (2D) (1D)
47
7 8 9 7 8 9

6 4 5 4 5 6
9 5
6 8 1 2 3 1 2 3
J

LINE LINE
3

3 Lead
TYPICAL WYE- CONNECTED MOTOR TYPICAL DELTA - CONNECTED MOTOR
1 J J
1 2
OPTIONAL T'STATS
OPTIONAL T'STATS
1 2 3
J
3 2 3
LINE

Notes:
1.Three lead motors may be designed as either wye-connected or delta-connected.
2. Interchange any two line leads to reverse rotation.
3. Optional thermostats are provided when specified.
4. Actual number of internal parallel circuits may vary.

15
Connection Diagrams
Blower Motor
Single Phase
1
2
3 LINE A LINE B JOIN
HIGH 1 4 2,3
4
LOW 1,3 2,4 ---
A PHASE

B PHASE

GREY OIL CAP

MOUNTED
RED INSIDE FAN
HOUSING

Three Phase

LOW VOLTAGE HIGH VOLTAGE

1

4 5 6
4 5 6
4
7 7 8 9 7 8 9
1 2 3 1 2 3

LINE LINE
6 9 5
8

3 2

Note: CCW from ODE of fan motor.

Interchange any two line leads to reverse rotation to direct air
flow over motor.

Note: Blower motor should be connected to line (mains) power

for proper operation. Do not connect blower to variable
frequency output of control to inverter or vector drive motor.
Allow sufficient clearance for air flow into blower. Restrictions
and blockage from debris may cause motor overheating.

16
Dimensions
TENV Inverter Drive® and Vector Drive® Motors

C (Z)
C (I)
GREASE FITTING AH AB
(EACH END) V
BB TAP

AJ
AK O DIA.

U
BD D

AA
2F BA E E
H

Rolled Steel Construction

NEMA
FRAME C (I) C (Z) D E 2F H AH O AB BA U V BD AK AJ TAP AA BB
56C N/A 11.54 3.5 2.44 3.00 0.34 2.06 6.81 5.22 2.75 0.625 2.19 6.50 4.50 5.88 3/8-16 0.88 0.13
143TC 12.13 16.61 4.00
145TC 13.00 17.48 3.5 2.44 5.00 0.38 2.12 6.81 5.22 2.75 0.875 2.25 6.50 4.50 5.88 3/8-16 0.88 0.13
182TC 4.50 0.75
184TC 14.99 19.47 4.5 3.75 5.50 0.41 2.62 8.44 5.97 3.50 1.125 2.75 8.86 8.50 7.25 1/2-13 NPT 0.25
213TC 5.50 0.75
215TC 17.55 21.54 5.25 4.25 7.00 0.41 3.12 10.03 7.46 4.25 1.375 3.25 9.04 8.50 7.25 1/2-13 NPT 0.25
254TC 8.25 1.25
256TC 26.56 25.67 6.25 5.00 10.00 0.53 3.75 12.00 8.99 4.75 1.625 3.87 9.44 8.50 7.25 1/2-13 NPT 0.25

Cast Iron Construction

NEMA
FRAME C (I) C (Z) D E 2F H AH O AB BA U V BD AK AJ TAP AA BB
143TC 4.00
145TC 11.82 15.85 3.5 2.75 5.00 0.38 2.12 7.59 6.43 2.25* 0.875 2.25 6.48 4.50 5.88 3/8-16 1.09 0.13
182TC 4.50
184TC 14.87 18.91 4.5 3.75 5.50 0.41 2.62 9.23 7.18 3.50 1.125 2.75 9.06 8.50 7.25 1/2-13 1.09 0.25
213TC 5.50
215TC 18.07 22.10 5.25 4.25 7.00 0.41 3.12 10.99 8.67 4.25 1.375 3.25 9.06 8.50 7.25 1/2-13 1.38 0.25
254TC 8.25
256TC 21.67 25.73 6.25 5.00 10.00 0.53 3.75 12.87 9.42 4.75 1.625 3.87 9.09 8.50 7.25 1/2-13 1.38 0.25
Note: Dimensions are for reference only.
C(I) Inverter, C(Z) Vector.
*Non-Nema BA dimension

17
Dimensions
TEBC Inverter Drive® and Vector Drive® Motors

C-1
AB
C-3 AH TAP
BB
CONN. LABEL AJ DIA
(FAN LEADS)
V

AK BD O

U D
LEAD HOLE

MILITARY CONNECTOR E
BA AA E
(VECTOR MOTORS ONLY) H 2F

NEMA
FRAME C-1 C-3 D E 2F H AH O AB BA U V BD AK AJ TAP AA BB
143TC 4.00
145TC 18.30 - 3.50 2.75 5.00 0.38 2.12 7.59 6.43 2.25* 0.875 2.25 6.48 4.50 5.88 3/8-16 1.06 0.16
182TC 4.50
184TC 21.71 - 4.50 3.75 5.50 0.41 2.62 9.23 7.18 3.50 1.125 2.75 9.06 8.50 7.25 1/2-13 1.06 0.25
213TC 5.50
215TC 30.07 29.57 5.25 4.25 7.00 0.41 3.12 10.99 8.61 4.25 1.375 3.37 9.06 8.50 7.25 1/2-13 1.38 0.25
254TC 8.25
256TC 33.97 33.47 6.25 5.00 10.00 0.53 3.75 12.87 9.42 4.75 1.625 4.00 9.09 8.50 7.25 1/2-13 1.38 0.25
284TC 9.50
286TC 37.26 36.76 7.00 5.50 11.00 0.56 4.37 14.44 13.12 4.75 1.875 4.62 10.50 10.50 9.00 1/2-13 2.00 0.25
324TC 10.50
326TC 39.70 39.2 8.00 6.25 12.00 0.65 5.00 16.25 14.62 5.25 2.125 5.25 13.40 12.50 11.00 5/8-11 2.00 0.25
364TC 11.25
365TC 42.02 41.52 9.00 7.00 12.25 0.66 5.63 18.38 14.96 5.87 2.375 5.88 12.89 12.50 11.00 5/8-11 2.50 0.25
404TC 12.25
405TC ** 46.92 10.00 8.00 13.75 0.81 7.00 20.31 17.74 6.62 2.875 7.25 12.89 12.50 11.00 5/8-11 3.00 0.25
444TC 14.50
445TC ** 52.23 11.00 9.00 16.50 0.81 8.25 22.85 20.45 7.50 3.375 8.50 16.68 16.00 14.00 5/8-11 3.00 0.25
445TC 16.50
447TC ** 55.73 11.00 9.00 20.00 0.81 8.25 22.85 20.45 7.50 3.375 8.50 16.68 16.00 14.00 5/8-11 3.00 0.25
447TC 20.00
449TC ** 64.50 11.00 9.00 25.00 0.81 8.25 22.94 21.71 7.50 3.375 8.50 16.77 16.00 14.00 5/8-11 3.00 0.25
Note: C-1 = Dimension includes single phase blower kit and fan motor. C-3 = Dimension includes three phase blower kit and fan motor.
Dimensions are for reference only. * Non-Nema BA dimension. ** Consult Baldor

5000 Frame
NEMA N-W
FRAME C-1 C-3 D E 2F H AH O AB BA U V AA
5007L 56.56 22.00 4.00
5009L N/A 77.81 12.50 10.00 28.00 0.94 11.62 26.84 26.88 8.50 3.875 11.12 NPT
28.00 4.00
5810 N/A 85.12 14.50 23.00 32.00 1.18 12.50 3.088 30.19 11.38 4.625 11.00 NPT
36.00
Note: Dimensions are for reference only.

Nema TS Style Shaft Dimensions

NEMA
FRAME C N U V
404TS
18 405TS 41.10 4.50 3.875 4.25
Dimensions
TEFC Inverter Drive® Explosion-Proof Motors

C
AB
BB AH

AK O

BD
U TAP
AJ DIA.
D

2F BA
H AA E E

Rolled Steel Construction

NEMA
FRAME D E 2F H AH O AB BA U V BD AK AJ TAP AA BB
0.50
56C 3.50 2.44 3.00 0.34 1.93 7.09 6.92 2.75 0.625 1.88 6.46 4.50 5.88 3/8-16 NPT 0.13
143TC 4.00 0.75
145TC 3.50 2.75 5.00 0.34 2.12 7.09 6.92 2.75 0.875 2.25 6.46 4.50 5.88 3/8-16 NPT 0.13

Cast Iron Construction

NEMA
FRAME D E 2F H AH O AB BA U V BD AK AJ TAP AA BB
182TC 4.50
184TC 4.50 3.75 5.50 0.41 2.62 9.56 8.55 3.50 1.125 2.75 8.96 8.50 7.25 1/2-13 0.75 0.13
213TC 5.50
215TC 5.25 4.25 7.00 0.41 3.12 10.75 9.66 4.25 1.375 3.37 9.05 8.50 7.25 1/2-13 0.75 0.25
254TC 8.25
246TC 6.25 5.00 10.00 0.53 3.75 12.87 9.42 4.75 1.625 4.00 9.09 8.50 7.25 1/2-13 1.38 0.25
284TC 9.50 14.56 12.12 11.12 1.25
286TC 7.00 5.50 11.00 0.53 4.38 14.75 12.18 4.75 1.875 4.62 11.15 10.50 9.00 1/2-13 NPT 0.25
324TC 10.50 1.50
326TC 8.00 6.25 12.00 0.65 5.00 16.68 12.87 5.25 2.125 5.25 13.38 12.50 11.00 5/8-11 NPT 0.25
2.50
364TC 9.00 7.00 11.25 0.65 5.63 18.50 17.51 5.88 2.375 5.88 12.50 12.50 11.00 5/8-11 NPT 0.25

Cast Iron Construction (Non-C-Face)

NEMA
FRAME D E 2F H N-W O AB BA U V AA
2.50
405T 10.00 8.00 13.75 0.81 7.56 21.00 18.35 6.62 2.875 7.25 NPT
Note: Dimensions are for reference only.

19
Motor Circuit Parameters Per Phase 230/460 Volt Ratings

R1 X1 X2 X 2B
R1 X1 X2

Xm R2 R 2B
Xm R2 S S NOTE: NEMA TS
S R 2E Frames have same
S circuit parameters as
equivalent NEMA TC
catalog numbers.

Motor Rating Vector Drive Motor Circuit

Ohms @ 20°C Ohms @ 20°C Ohms @ 20°C Watts Watts % of
60Hz Resistance Primary Self Leakage Irons Loss Mechanical Synchronous
NEMA Inductance Inductance Xm (Total) Loss Speed
Frame Magnetic Flux Magnetic Flux (Total) Slip
HP RPM Catalog # Type R1 R2 R2B R2E X1 X2 X2B No Full
100% 90% 100% 90% Load Load
0.33 1725 56C IDNM3534 3513M 28.3 24.3 - - 885 888 34.7 22.3 - 17 14 14 0.278 3.82
0.50 1725 56C IDNM3538 3516M 20.0 12.1 - - 475 485 17.5 12.2 - 32 26 14 0.177 2.81
0.75 1725 56C IDNM3542 3520M 11.0 8.92 - - 389 397 13.2 10 - 40 32 14 0.146 2.99
1 1750 143TC ZDWNM3546T 3524M 7.55 5.29 - - 310 320 9.97 8.04 - 31 25 14 0.0972 2.31
1 1725 143TC ZDNM3581T 0524M 9.19 6.14 - - 283 292 9.15 7.38 - 55 44 14 0.118 2.74
1 1725 143TC ZDM3581T 0516M 9.2 6.39 - - 196 222 8.74 5.97 - 69 53 14 0.141 2.95
1 1150 145TC ZDM3582T 0524M 9.74 7.03 - - 217 223 14.1 11.8 - 23 19 9 0.0937 3.34
1.5 1750 145TC ZDWNM3554T 3535M 4.27 3.36 - - 211 219 6.15 5.5 - 46 37 14 0.0781 2.14
1.5 1725 145TC ZDNM3584T 0532M 5.16 3.92 - - 246 252 7.25 6.35 - 64 52 14 0.0833 2.54
1.5 1725 143TC ZDM3584T 0520M 6.02 4.33 - - 139 160 5.95 4.42 - 95 72 14 0.116 2.95
1.5 1160 182TC ZDM3667T 0623M 3.68 3.0 - - 146 147 12.9 10.4 - 37 30 19 0.0742 2.17
2 1725 182TC ZDWNM3609T 3628M 3.04 2.7 - - 164 173 5.51 4.44 - 101 80 24 0.0938 2.33
2 1725 182TC ZDNM3669T 0628M 3.04 2.7 - - 164 173 5.51 4.44 - 101 80 24 0.0938 2.33
2 1725 145TC ZDM3587T 0528M 4.36 3.45 - - 147 163 5.02 4.21 - 99 77 14 0.0972 3.05
2 1160 184TC ZDM3664T 0628M 2.36 2.11 - - 105 105 9.11 7.47 - 52 42 19 0.0638 2.00
3 1750 184TC ZDWNM3611T 3634M 1.77 1.34 - - 139 142 5.25 4.57 - 78 63 24 0.0556 1.72
3 1750 184TC ZDNM3661T 0634M 2.36 1.7 - - 137 138 5.71 4.48 - 47 38 24 0.0486 2.22
3 1760 182TC ZDM3661T 0628M 1.89 1.33 - - 122 132 5.09 4.23 - 83 66 24 0.0582 1.73
3 1160 213TC ZDM3764T 0735M 1.38 4.8 1.26 0.207 71.2 76.2 4.48 3.37 5.95 58 47 24 0.0365 1.61
5 1760 213TC ZDWNM3707T 3735M 0.852 2.28 0.598 0.175 73.8 79.9 2.72 1.68 2.83 101 81 59 0.0399 1.37
5 1760 213TC ZDNM3767T 0735M 0.852 2.28 0.598 0.175 73.8 79.9 2.72 1.68 2.83 101 81 59 0.0399 1.37
5 1750 184TC ZDM3665T 0640M 1.28 0.957 - - 76.7 79.5 2.73 2.13 - 85 68 24 0.0382 2.03
5 1160 215TC ZDM3768T 0750M 0.877 3.54 0.933 0.107 54 56.8 3.17 2.51 4.41 79 64 24 0.0299 1.88
7.5 1765 254TC ZDWNM22937T 3940M 0.469 0.371 - - 60.5 60.8 1.89 2.16 - 113 90 119 0.0347 1.15
7.5 1760 254TC ZDNM2237T 0932M 0.556 1.25 0.33 0.0976 48.7 49.9 1.62 0.951 1.63 210 163 134 0.0417 1.13
7.5 1760 213TC ZDM3770T 0735M 0.733 2.02 0.53 0.155 59.2 68.5 2.37 1.44 2.5 114 92 59 0.0382 1.86
7.5 1180 254TC ZDM2276T 0940M 0.573 1.12 0.334 0.112 43.4 45.8 2.09 1.84 2.39 123 98 59 0.0247 1.20
10 1765 256TC ZDWNM22938T 3936M 0.371 0.321 - - 56.4 56.5 1.65 2.06 - 121 98 119 0.0313 1.33
10 1760 256TC ZDNM2238T 0948M 0.331 1.0 0.264 0.0521 39.8 40.3 1.23 0.871 1.31 253 204 134 0.033 1.08
10 1760 215TC ZDM3774T 0750M 0.441 1.48 0.391 0.0799 45.4 51.4 1.6 1.08 1.85 157 126 59 0.0295 1.64
10 1180 256TC ZDM2332T 0952M 0.459 0.954 0.284 0.084 36.2 38.7 1.8 1.63 2.03 145 116 59 0.0221 1.33
15 1765 254TC ZDM2333T 0940M 0.292 0.227 - - 33.9 36.7 1.16 1.35 - 188 150 134 0.0286 1.43
15 1170 284TC ZDM4100T 1050M 0.323 0.932 0.212 0.0638 36.3 37.2 1.39 1.13 1.76 204 163 104 0.0286 1.56
20 1765 256TC ZDM2334T 0952M 0.206 0.174 - - 27 29.4 0.877 1.08 - 236 188 134 0.0243 1.45
20 1170 286TC ZDM4102T 1060M 0.22 0.7 0.159 0.04 26.4 27.7 0.975 0.812 1.32 276 219 104 0.0247 1.47
25 1780 284TC ZDM4103T 1050M 0.141 0.635 0.0923 0.0297 18.2 20 0.655 0.509 0.862 269 215 229 0.0217 1.16
25 1180 324TC ZDM4111T 1256M 0.118 0.364 0.102 0.0245 18.9 19.9 0.68 0.491 0.982 325 259 119 0.0156 1.09
30 1780 286TC ZDM4104T 1058M 0.118 0.597 0.0869 0.025 17.7 19.1 0.594 0.478 0.811 287 229 229 0.02 1.28
30 1180 326TC ZDM4117T 1262M 0.0969 0.319 0.0897 0.0196 16.3 17.4 0.571 0.417 0.861 373 298 119 0.0143 1.12
40 1780 324TC ZDM4110T 1258M 0.0601 0.711 0.0438 0.0132 12.9 13.8 0.412 0.211 0.54 438 350 399 0.0182 0.899
40 1185 364TC ZDM4308T 1458M 0.0725 0.0574 - - 11.5 12 0.448 0.395 - 402 320 269 0.0143 0.944
50 1780 326TC ZDM4115T 1272M 0.0489 0.594 0.0366 0.0098 10.4 11.4 0.334 0.177 0.451 527 421 399 0.0156 0.914
50 1185 365TC ZDM4312T 1468M 0.0559 0.0467 - - 9.52 9.96 0.358 0.326 - 484 386 269 0.0124 0.955

Continued on next page...

20
Motor Circuit Parameters Per Phase 230/460 Volt Ratings
Motor Rating Vector Drive Motor Circuit
Ohms @ 20°C Ohms @ 20°C Ohms @ 20°C Watts Watts % of
60Hz Resistance Primary Self Leakage Irons Loss Mechanical Synchronous
NEMA Inductance Inductance Xm (Total) Loss Speed
Frame Magnetic Flux Magnetic Flux (Total) Slip
HP RPM Catalog # Type R1 R2 R2B R2E X1 X2 X2B No Full
100% 90% 100% 90% Load Load
60 1780 364TC ZDM4314T 1462M 0.0431 0.135 0.0323 0.0082 9.61 9.89 0.248 0.146 0.428 509 405 649 0.0156 0.832
60 1185 404TC ZDM4403T 1672M 0.0474 0.0325 - - 9.17 9.71 0.259 0.371 - 533 425 299 0.0091 0.784
60 1180 404TS ZDM4403TS 1672M 0.0498 0.0316 - - 7.06 7.85 0.267 0.595 - 716 574 299 0.0111 0.798
75 1780 365TC ZDM4316T 1480M 0.0354 0.119 0.0285 0.0065 8.42 8.71 0.222 0.13 0.377 578 460 649 0.0139 0.900
75 1185 405TC ZDM4404T 1684M 0.0382 0.0269 - - 7.68 8.24 0.211 0.315 - 629 502 299 0.0085 0.812
75 1180 405TS ZDM4404TS 1684M 0.0358 0.0258 - - 5.8 6.54 0.225 0.494 - 855 686 299 0.0104 0.817
100 1780 405TC ZDM4400T-4 1680M 0.0296 0.0828 0.0157 0.0062 8.67 9.39 0.224 0.118 0.329 560 448 799 0.0104 0.804
100 1180 444TC ZDM4409T-4 1880M 0.0211 0.0164 - - 5.22 5.6 0.171 0.255 - 819 654 669 0.0091 0.669
125 1780 444TC ZDM4410T-4 1880M 0.0173 0.0354 0.0106 0.0033 5.43 5.97 0.131 0.133 0.176 902 720 1499 0.0113 0.580
150 1780 445TC ZDM4406T-4 1892M 0.0134 0.0299 0.009 0.0024 4.47 5.01 0.104 0.112 0.149 1074 858 1499 0.0095 0.562
200 1780 447TC ZDM4407T-4 18112M 0.0100 0.0253 0.0076 0.0017 3.85 4.26 0.0817 0.0951 0.126 1275 1017 1499 0.0078 0.604
250 1780 449TC ZDM4408T-4 18136M 0.0074 0.0208 0.0062 0.0011 3.16 3.5 0.0658 0.0781 0.103 1554 1240 1499 0.0069 0.594
300 1785 449TC ZDM44304T-4 18160M 0.0058 0.0173 0.0052 0.0008 2.58 2.9 0.0498 0.065 0.0862 1876 1496 1499 0.0061 0.573
350 1785 449TC ZDM44354T-4 18168M 0.0056 0.0164 0.0049 0.0007 2.44 2.74 0.0465 0.0616 0.0817 1982 1581 1499 0.0056 0.635
400 1785 5007L ZDM50404L-4 20141M 0.0037 0.002 - - 2.45 2.75 0.039 0.119 - 2827 2217 1089 0.1 0.8
450 1790 5007L ZDM50454L-4 20153M 0.0027 0.0017 - - 2.04 2.4 0.0327 0.105 - 3234 2461 1108 0.1 0.6
500 1790 5007L ZDM50504L-4 20173M 0.0023 0.0013 - - 1.84 2.15 0.028 0.094 - 3629 2863 1134 0.1 0.6

Motor Circuit Parameters Per Phase 575 Volt Ratings

Motor Rating Vector Drive Motor Circuit

Ohms @ 20°C Ohms @ 20°C Ohms @ 20°C Watts Watts % of
60Hz Resistance Primary Self Leakage Irons Loss Mechanical Synchronous
NEMA Inductance Inductance Xm (Total) Loss Speed
Frame Magnetic Flux Magnetic Flux (Total) Slip
HP RPM Catalog # Type R1 R2 R2B R2E X1 X2 X2B No Full
100% 90% 100% 90% Load Load
1 1750 143TC ZDM3581T-5 0524M 11.9 8.22 - - 480 497 15.5 12.5 - 31 25 14 0.0972 2.30
1.5 1750 145TC ZDM3584T-5 0528M 7.91 5.81 - - 322 355 10.6 8.87 - 43 35 14 0.0833 2.42
2 1750 145TC ZDM3587T-5 0535M 6.66 5.17 - - 323 336 9.45 8.44 - 47 38 14 0.0781 2.87
3 1760 182TC ZDM3661T-5 0628M 3.24 2.1 - - 194 209 8.04 6.68 - 82 66 24 0.059 1.75
5 1750 184TC ZDM3665T-5 0640M 1.89 1.53 - - 123 127 4.35 3.4 - 83 67 24 0.0399 2.06
7.5 1760 213TC ZDM3770T-5 0735M 1.05 0.636 - - 80.9 91.8 3.76 3.65 - 129 104 59 0.0295 1.32
10 1760 215TC ZDM3774T-5 0750M 0.711 0.488 - - 70.9 77 2.9 3.04 - 160 127 59 0.026 1.33
15 1760 254TC ZDM2333T-5 0942M 0.445 0.35 - - 51.9 56.5 1.79 2.08 - 190 152 134 0.0278 1.41
20 1765 256TC ZDM2334T-5 0952M 0.32 0.268 - - 41.3 45.3 1.35 1.67 - 239 191 134 0.0243 1.43
25 1780 286TC ZDM4103T-5 1050M 0.222 0.992 0.144 0.0465 28.4 31.3 1.02 0.796 1.35 269 215 229 0.0217 1.16
30 1780 286TC ZDM4104T-5 1056M 0.187 0.938 0.136 0.0393 27.8 30 0.938 0.752 1.27 285 228 229 0.02 1.29
40 1780 324TC ZDM4110T-5 1258M 0.117 1.27 0.0785 0.0261 23.6 24.9 0.776 0.391 0.967 379 302 399 0.02 1.08
50 1780 326TC ZDM4115T-5 1272M 0.092 1.09 0.0672 0.018 20.6 21.4 0.628 0.336 0.827 444 354 399 0.0174 1.09
60 1780 364TC ZDM4314T-5 1462M 0.0806 0.228 0.0546 0.016 17.3 18.2 0.493 0.341 0.765 501 399 649 0.0182 0.962
75 1780 365TC ZDM4316T-5 1480M 0.0605 0.19 0.0455 0.0103 14.8 15.3 0.365 0.272 0.639 604 480 649 0.0148 0.929
100 1780 404TC ZDM4400T-5 1680M 0.0446 0.124 0.0234 0.0092 12.6 13.9 0.333 0.175 0.492 587 470 799 0.0104 0.765
125 1780 444TC ZDM4410T-5 1880M 0.0279 0.056 0.0168 0.0052 8.65 9.45 0.207 0.211 0.278 891 711 1499 0.0113 0.587
150 1780 445TC ZDM4406T-5 1892M 0.0209 0.0466 0.014 0.0038 6.91 7.78 0.153 0.175 0.232 1082 864 1499 0.0095 0.558

21
Optional Accessories
Cable Assembly Kits
For the convenience of our customers, we offer a cable with a wired motor-end M.S. connector
mating plug for feedback from Vector Drive Motors.
CATALOG CABLE APPROX.
NO. LENGTH WEIGHT
CBL015ZD-2 5 FEET = 1.5 METERS 2
CBL030ZD-2 10 FEET = 3.0 METERS 2.5
CBL046ZD-2 15 FEET = 4.6 METERS 3
CBL061ZD-2 20 FEET = 6.1 METERS 4
CBL091ZD-2 30 FEET = 9.1 METERS 5
CBL152ZD-2 50 FEET = 15.2 METERS 6
CBL229ZD-2 75 FEET = 22.9 METERS 7
CBL305ZD-2 100 FEET = 30.5 METERS 8
CBL379ZD-2 125 FEET = 38.1 METERS 12
CBL455ZD-2 150 FEET = 45.7 METERS 14
CBL606ZD-2 200 FEET = 61.0 METERS 16

Connection Diagram for Cable Assembly Kit

ENCODER MS CONNECTOR WIRE RESOLVER
CONNECTION PIN OUT COLOR CONNECTION
A A GREY SINE (+)
A H VIOLET SINE (-)
B B YELLOW COS (+)
B J ORANGE COS (-)
Z (or C) C BLUE –
Z (or C) K GREEN –
+5VDC D WHITE EXCITATION (REF HIGH)
SHIELD E SHIELD SHIELD
CIRCUIT GROUND F BLACK COMMON (REF LOW)
CASE GROUND G – –

Encoder and Resolver Feedback Kits

CATALOG FRAME
NO. SIZE ENCLOSURE DESCRIPTION
ENCMT ALL ALL All pieces to mount an H-25 (F-1 face mount) encoder or resolver to an
Inverter Drive Motor (less the encoder/resolver and M.S. Connectors)
ENC00NV ALL TENV Encoder, M.S. Connector and hardware for mounting encoder to an
Inverter Drive Motor.
ENC01BC 145TC-215TC TEBC Encoder, M.S. Connector and hardware for mounting encoder to an
Inverter Drive Motor.
ENC02BC 254TC-447TC TEBC Encoder, M.S. Connector and hardware for mounting encoder to an
Inverter Drive Motor.
RES00NV ALL TENV Resolver, M.S. Connector and hardware for mounting resolver to an
Inverter Drive Motor.
RES01BC 145TC-215TC TEBC Resolver, M.S. Connector and hardware for mounting resolver to an
Inverter Drive Motor.
RES02BC 254TC-447TC TEBC Resolver, M.S. Connector and hardware for mounting resolver to an
Inverter Drive Motor.
Note: Consult Baldor for information on 449TC, 5007, 5009L, 5810 designs.

22
Blower Kits – Single Phase
Blower Motor housing and mounting hardware for spare units or different power supplies.
CATALOG FRAME APPROX.
NO. VOLTAGE PHASE HZ SIZE WEIGHT
BLWL05-L 115 1 50/60 143T-145T 20
BLWL06-L 115 1 50/60 182T-184T 22
BLWL07-L 115 1 50/60 213T-215T 25
BLWL09-L 115 1 50/60 254T-256T 27
BLWL10-L 115 1 50/60 284T-286T 38
BLWL12-L 115 1 50/60 324T-326T 42
BLWL14-L 115 1 50/60 364T-365T 45

Blower Kits – Three Phase

Blower Motor housing and mounting hardware for spare units or different power supplies.
CATALOG FRAME APPROX.
NO. VOLTAGE PHASE HZ SIZE WEIGHT
BLWM07-F 230/380-460 3 60/50-60 213T-215T 25
BLWM09-F 230/380-460 3 60/50-60 254T-256T 27
BLWM10-F 230/380-460 3 60/50-60 284T-286T 32
BLWM12-F 230/380-460 3 60/50-60 324T-326T 38
BLWM14-F 230/380-460 3 60/50-60 364T-365T 45
BLWM16-F 230/415-460 3 60/50-60 404T-405T 70
BLWM18-F 230/415-460 3 60/50-60 444T-447T 120
Note: Consult Baldor for information on 447T-449T, 5007, 5009L, 5810 designs.

Blower Motor Specifications

BLOWER MOTORS ON TEBC A.C. MOTORS
MAIN
MOTOR BLOWER MOTOR SPECS
FRAME HP POLES VOLTS PH HZ AMPS P.F. CAP. AMPS
FULL LOAD mf L.R.A.
143/145TC 0.05 2 115*/** 1 60 0.54 95 N/A –
0.05 2 230 1 60 0.27 95 N/A –
182/184TC 0.05 2 115*/** 1 60 0.27 96 N/A 0.47
0.05 2 230 1 60 0.13 96 N/A 0.23
213/215TC
254/256TC
284/286TC 0.20 2 115/230** 1 60 2.6/1.3 94 6 5.8/2.9
324/326TC 0.20 2 230/460* 3 60 0.8/0.4 85 N/A 3.0/1.5
364/365TC
404/405TC
444/445TC
447-449TC
5007L
5009L Consult Baldor
5810
Note: Nema 56C TENV motors do not require additional ventilation.
* Standard blower for 230/460 volt motor ratings.
** Standard blower for 575 volt motor ratings.
Consult Baldor for information on Nema 5007L, 5009L, and 5810 designs.

23
 Other quality products from Baldor to serve your Motor
and Drive needs.
No one offers a broader line of motors
and controls than Baldor–no one!

Baldor Super-E® Premium

Efficient Motors Baldor AC Induction Servos
Baldor Series 15H & Spindle Drive Motors
Baldor’s Premium Efficient Super-E®
Motors are designed for applications Inverters Baldor AC Induction Servos are designed
where savings in operating cost are high Baldor stock inverters from 1-500 hp are to be operated closed loop from our H and
enough to result in a “payback” within a the perfect solution for applications M Series Vector Drives providing top
relatively short period of time. ranging from HVAC and pumping to speeds to 8000 RPM.
Super-E® Motor features include: material handling and packaging Standard features include:
• More copper, larger wire, more iron, equipment. NEMA 4X enclosures are also • 3 to 60 Hp continuous duty - Premium
thinner laminations, and premium available to 20 hp for food processing Efficient windings
grade electrical steel applications. NEMA 1 and 12 pre- • Blower-cooled aluminum frames with
• Precision air gap between stator engineered panels featuring HOA and cast iron endplates for structural stability
and rotor manual bypass are also available. • Oversize internal shafting assures
• Premium anti-friction bearings Inverter features include: critical speed above normal operating
• Low loss cooling fan design • Tactile feel English language keypad range
• 200°C moisture resistant • 15 preset speeds • Precision balance
ISR Inverter Spike Resistant® wire • Controlled reversing • Standard encoder feedback, optional
• 200% peak overload capacity resolver
• Separate accel and decel rates • IEC B5 D-flange or NEMA C-face, both
• Process follower inputs with base mount
• DC injection braking • ISR Inverter Spike Resistant® magnet
• Dynamic braking wire and standard Class H insulation
Options include: system
• Serial communications • Standard ball bearing or optional roller
• High resolution analog I/O bearing on drive end
• Electronic gearing • Optional spring-set holding brake
• Interposing relay board • Special windings for wye-delta
• 3-15 PSI pneumatic interface switching allowing extended speed
range
Baldor Series 18H Vector
Baldor Vector Controls provide precise
speed and torque control. The unique
“Auto Tune” feature enables the control to
adjust itself to the motor using only the
motor nameplate information. Features of
the Vector controls include:
• Speed Range: 4000:1
• Constant Torque: 0-1800 RPM
• Constant HP: 1800-4000 RPM Baldor Electric Company
• Stepless Accel-Decel P.O. Box 2400
• Homing/Orientation Fort Smith, AR 72902-2400 U.S.A.
• No cogging at low speeds Ph (501) 646-4711 • Fax (501) 648-5792
• Selectable speed or torque control International Fax (501) 648-5895
• Stock ratings from 1-500 HP in NEMA 1 www.baldor.com
© Baldor Electric Company Printed in U.S.A.
enclosures BR400 2/98 LITHO 25M
• NEMA 4X enclosures available to 20 HP