QUINT4-PS/1AC/24DC/5: Power Supply Unit
QUINT4-PS/1AC/24DC/5: Power Supply Unit
QUINT4-PS/1AC/24DC/5: Power Supply Unit
Data sheet
107099_en_01 © PHOENIX CONTACT 2018-09-03
1 Description
QUINT POWER power supplies with SFB Technology and
preventive function monitoring ensure superior system Technical data (short form)
availability. Input voltage range 100 V AC ... 240 V AC
-15 % ... +10 %
Powerful Mains buffering ≥ 24 ms (120 V AC)
≥ 32 ms (230 V AC)
– SFB technology: 6 times the nominal current for 15 ms
Nominal output voltage (UN) 24 V DC
– Power reserves:
Setting range of the output voltage 24 V DC ... 29.5 V DC
Static boost of up to 125% (PN) for a sustained period (USet)
Dynamic boost of up to 200% (PN) for 5 s Nominal output current (IN) 5A
Static Boost (IStat.Boost) 6.25 A
Robust Dynamic Boost (IDyn.Boost) 10 A (5 s)
Selective Fuse Breaking (ISFB) 30 A (15 ms)
– Mains buffering ≥ 20 ms Output power (PN) 120 W
– High degree of electrical immunity, thanks to integrated Output power (PStat. Boost) 150 W
Output power (PDyn. Boost) 240 W
gas-filled surge arrester (6 kV)
Efficiency typ. 88.8 % (120 V AC)
typ. 89.2 % (230 V AC)
Preventive
Residual ripple < 30 mVPP
– Comprehensive signaling: MTBF (IEC 61709, SN 29500) > 930000 h (40 °C)
Analog signal, digital signal, relay contact, LED bar Ambient temperature (operation) -25 °C ... 70 °C
graph -40°C (startup type tested)
> 60 °C Derating: 2.5 %/K
All technical specifications are nominal values and refer to a room temperature of 25 °C and 70 % relative
humidity at 100 m above sea level.
QUINT4-PS/1AC/24DC/5
2 Table of contents
1 Description .............................................................................................................................. 1
2 Table of contents ..................................................................................................................... 2
3 Ordering data .......................................................................................................................... 3
4 Technical data ......................................................................................................................... 5
5 Safety and installation notes .................................................................................................. 16
6 High-voltage test (HIPOT) ..................................................................................................... 17
7 Structure of the power supply ................................................................................................ 19
8 Mounting/removing the power supply .................................................................................... 22
9 Device connection terminal blocks ........................................................................................ 25
10 Output characteristic curves .................................................................................................. 27
11 Configuring the power supply ................................................................................................ 30
12 Boost currents ....................................................................................................................... 31
13 SFB technology ..................................................................................................................... 33
14 Signaling................................................................................................................................ 37
15 Operating modes ................................................................................................................... 45
16 Derating................................................................................................................................. 47
3 Ordering data
4 Technical data
Input data
Unless otherwise stated, all data applies for 25°C ambient temperature, 230 V AC input voltage, and nominal
output current (IN).
The SCCR value (short-circuit current rating) of the power supply unit corresponds to the SCCR value of the
backup fuse (see input protection table).
The external backup fuse must be approved for the (AC) supply voltage used and the voltage level.
Housing
Input Signaling
(+)
L
N B
(-)
B
A D
PE Output
+
A B C D
Type test (IEC/EN 60950-1) 2.5 kV AC 4 kV AC 0.5 kV DC 0.5 kV DC
Production test 2 kV AC 2 kV AC 0.5 kV DC 0.5 kV DC
Field test (with gas-filled surge arrester) 0.8 kV AC 0.8 kV AC 0.5 kV DC 0.5 kV DC
1.1 kV DC 1.1 kV DC
Field test (gas-filled surge arrester de-contacted) 2 kV AC 2 kV AC 0.5 kV DC 0.5 kV DC
2.83 kV DC 2.83 kV DC
POWER factor
1,0
Power Factor
0,9
0,8
0,7
0,6
0,5 = UIn: 120 V AC/UOut: 24 V DC
= UIn: 230 V AC/UOut: 24 V DC
0,4
1 2 3 4 5 6 7 8 9 10
IOut [A]
IOut [A]
Output data
Nominal output voltage (UN) 24 V DC
Setting range of the output voltage (USet) ( constant 24 V DC ... 29.5 V DC
capacity )
Nominal output current (IN) 5A
Static Boost (IStat.Boost) 6.25 A
Dynamic Boost (IDyn.Boost) 10 A (5 s)
Selective Fuse Breaking (ISFB) 30 A (15 ms)
Magnetic circuit breaker tripping A1...A4 / B2 / C1...C2 / Z1...Z4
Control deviation Static load change 10 % ... 90 % < 0.5 %
Control deviation Dynamic load change 10 % ... 90 %, (10 < 4 %
Hz)
Control deviation change in input voltage ±10 % < 0.25 %
Short-circuit-proof yes
No-load proof yes
Residual ripple ( with nominal values ) < 30 mVPP
Connection in parallel Yes, for redundancy and increased capacity
Connection in series yes
Output data
Feedback resistance ≤ 35 V DC
Protection against surge voltage on the output ≤ 32 V DC
Rise time typical 50 ms (UOut = 10 % ... 90 %)
LED signaling
POut > 100% LED lights up yellow, output power > 120 W
POut > 75% LED lights up green, output power > 90 W
POut > 50% LED lights up green, output power > 60 W
UOut > 0.9 x USet LED lights up green
UOut < 0.9 x USet LED flashes green
Reliability 230 V AC
MTBF (IEC 61709, SN 29500) > 1532000 h (25 °C)
> 930000 h (40 °C)
> 431000 h (60 °C)
General data
Degree of protection IP20
Protection class I
Inflammability class in acc. with UL 94 (housing / terminal V0
blocks)
Side element version Aluminum
Hood version Stainless steel X6Cr17
Dimensions W / H / D (state of delivery) 36 mm / 130 mm / 125 mm
Dimensions W / H / D (90° turned) 122 mm / 130 mm / 39 mm
Weight 0.7 kg
90
85
80
Ambient conditions
Ambient temperature (operation) -25 °C ... 70 °C (> 60 °C Derating: 2.5 %/K)
The ambient temperature (operation) refers to UL 508 surrounding air temperature.
Standards
Safety of power supply units up to 1100 V (insulation DIN EN 61558-2-16
distances)
Safety transformers for power supply units EN 61558-2-16 (air clearances and creepage distances only)
Electrical safety (of information technology equipment) IEC 60950-1/VDE 0805 (SELV)
Electrical safety (of control and regulation devices) IEC 61010-1
SELV IEC 60950-1 (SELV)
EN 60204-1 (PELV)
Limitation of mains harmonic currents EN 61000-3-2
Network version/undervoltage SEMI F47-0706; EN 61000-4-11
Standards
Rail applications EN 50121-3-2
EN 50121-4
EN 50121-5
IEC 62236-3-2
IEC 62236-4
IEC 62236-5
EMC requirements, power plant IEC 61850-3
EN 61000-6-5
HART FSK Physical Layer Test Specification Compliance Output voltage UOut compliant
Approvals
UL UL Listed UL 508
UL/C-UL Recognized UL 60950-1
UL ANSI/ISA-12.12.01 Class I, Division 2, Groups A, B, C, D
(Hazardous Location)
CSA CAN/CSA-C22.2 No. 60950-1-07
CSA-C22.2 No. 107.1-01
SIQ BG (type approved)
Electromagnetic compatibility
Noise emission according to EN 61000-6-3 (residential and commercial) and EN 61000-6-4 (industrial)
CE basic standard Minimum normative Higher requirements in
requirements practice (covered)
Conducted noise emission EN 55016 EN 61000-6-4 (Class A) EN 61000-6-3 (Class B)
Noise emission EN 55016 EN 61000-6-4 (Class A) EN 61000-6-3 (Class B)
Harmonic currents EN 61000-3-2 EN 61000-3-2 (Class A) EN 61000-3-2 (Class A)
Flicker EN 61000-3-3 not required EN 61000-3-3 (Class A)
Immunity according to EN 61000-6-1 (residential), EN 61000-6-2 (industrial), and EN 61000-6-5 (power station
equipment zone), IEC/EN 61850-3 (energy supply)
CE basic standard Minimum normative Higher requirements in
requirements of practice (covered)
EN 61000-6-2 (CE)
(immunity for industrial
environments)
Electrostatic discharge EN 61000-4-2
Housing contact discharge 4 kV (Test Level 2) 8 kV (Test Level 4)
Housing air discharge 8 kV (Test Level 3) 15 kV (Test Level 4)
Comments Criterion B Criterion A
Electromagnetic HF field EN 61000-4-3
Frequency range 80 MHz ... 1 GHz 80 MHz ... 1 GHz
Test field strength 10 V/m (Test Level 3) 20 V/m (Test Level 3)
Frequency range 1.4 GHz ... 2 GHz 1 GHz ... 6 GHz
Test field strength 3 V/m (Test Level 2) 10 V/m (Test Level 3)
Frequency range 2 GHz ... 2.7 GHz 1 GHz ... 6 GHz
Test field strength 1 V/m (Test Level 1) 10 V/m (Test Level 3)
Comments Criterion A Criterion A
Fast transients (burst) EN 61000-4-4
Input 2 kV (Test Level 3 - 4 kV (Test Level 4 -
asymmetrical) asymmetrical)
Output 2 kV (Test Level 3 - 4 kV (Test Level 4 -
asymmetrical) asymmetrical)
Signal 1 kV (Test Level 3 - 4 kV (Test Level 4 -
asymmetrical) asymmetrical)
Comments Criterion B Criterion A
Immunity according to EN 61000-6-1 (residential), EN 61000-6-2 (industrial), and EN 61000-6-5 (power station
equipment zone), IEC/EN 61850-3 (energy supply)
CE basic standard Minimum normative Higher requirements in
requirements of practice (covered)
EN 61000-6-2 (CE)
(immunity for industrial
environments)
Surge voltage load (surge) EN 61000-4-5
Input 1 kV (Test Level 3 - 3 kV (Test Level 4 -
symmetrical) symmetrical)
2 kV (Test Level 3 - 6 kV (Test Level 4 -
asymmetrical) asymmetrical)
Output 0.5 kV (Test Level 2 - 1 kV (Test Level 3 -
symmetrical) symmetrical)
0.5 kV (Test Level 1 - 2 kV (Test Level 3 -
asymmetrical) asymmetrical)
Signal 1 kV (Test Level 2 - 1 kV (Test Level 2 -
asymmetrical) asymmetrical)
Comments Criterion B Criterion A
Conducted interference EN 61000-4-6
Input/Output/Signal asymmetrical asymmetrical
Frequency range 0.15 MHz ... 80 MHz 0.15 MHz ... 80 MHz
Voltage 10 V (Test Level 3) 10 V (Test Level 3)
Comments Criterion A Criterion A
Power frequency magnetic field EN 61000-4-8
50 Hz , 60 Hz ( 30 A/m ) 16.7 Hz , 50 Hz , 60 Hz
( 100 A/m 60 s )
not required 50 Hz , 60 Hz ( 1 kA/m , 3 s )
not required 0 Hz ( 300 A/m , DC, 60 s )
Comments Criterion A Criterion A
Voltage dips EN 61000-4-11
Input voltage ( 230 V AC , 50 Hz )
Voltage dip 70 % , 25 periods 70 % , 0.5 / 1 / 25 periods
( Test Level 2 ) ( Test Level 2 )
Comments Criterion C Criterion A: 0.5 / 1 / 25 periods
Voltage dip 40 % , 10 periods 40 % , 5 / 10 / 50 periods
( Test Level 2 ) ( Test Level 2 )
Comments Criterion C Criterion A
Voltage dip 0 % , 1 period 0 % , 0,5 / 1 / 5 / 50 / 250
( Test Level 2 ) periods ( Test Level 2 )
Comments Criterion B Criterion A: 0.5 / 1 period
Criterion B: 5 / 50 / 250 periods
Additional basic standard EN 61000-6-5 (immunity in power station), IEC/EN 61850-3 (energy supply)
Basic standard Minimum normative Higher requirements in
requirements of EN 61000- practice (covered)
6-5
Pulse-shape magnetic field EN 61000-4-9
not required 1000 A/m
Comments none Criterion A
Damped oscillating magnetic field EN 61000-4-10
not required 100 kHz
110 A/m
not required 1 MHz
110 A/m
Comments none Criterion A
Attenuated sinusoidal oscillations (ring wave) EN 61000-4-12
Input not required 2 kV (Test Level 4 -
symmetrical)
not required 4 kV (Test Level 4 -
asymmetrical)
Comments none Criterion A
Asymmetrical conducted disturbance variables EN 61000-4-16
Input, Output, Signals 15 Hz ... 150 Hz , 10 V on 1 V 15 Hz ... 150 Hz , 30 V on 3 V
150 Hz ... 1.5 kHz , 1 V 150 Hz ... 1.5 kHz , 3 V
1.5 kHz ... 15 kHz , 1 V on 10 V 1.5 kHz ... 15 kHz , 3 V on 30 V
15 kHz ... 150 kHz , 10 V 15 kHz ... 150 kHz , 30 V
( Test Level 3 ) ( Test Level 4 )
50 Hz , 60 Hz , 10 V 16.7 Hz , 50 Hz , 60 Hz , 30 V
(Permanent) (Permanent)
50 Hz , 60 Hz , 100 V 16.7 Hz , 50 Hz , 60 Hz , 300 V
(1 s) (1 s)
( Test Level 3 ) ( Test Level 4 )
Comments Criterion A Criterion A
Attenuated oscillating wave EN 61000-4-18
Input, Output 1 MHz , 1 kV ( Test Level 3 - 100 kHz , 1 MHz , 1 kV ( Test
symmetrical ) Level 3 - symmetrical )
10 MHz , 1 kV 10 MHz , 1 kV
1 MHz , 2.5 kV 100 kHz , 1 MHz , 2.5 kV
( Test Level 3 - asymmetrical ) ( Test Level 3 - asymmetrical )
Signals 1 MHz , 1 kV 100 kHz , 1 MHz , 1 kV
( Test Level 3 - symmetrical ) ( Test Level 3 - symmetrical )
1 MHz , 2.5 kV 100 kHz , 1 MHz , 2.5 kV
( Test Level 3 - asymmetrical ) ( Test Level 3 - asymmetrical )
Comments Criterion B Criterion A
Key
Criterion A Normal operating behavior within the specified limits.
Criterion B Temporary impairment to operational behavior that is corrected by the device itself.
Criterion C Temporary adverse effects on the operating behavior, which the device corrects
automatically or which can be restored by actuating the operating elements.
6.3.1 Performing high-voltage testing 6.3.2 Disconnecting the gas-filled surge arrester
If high-voltage testing of the control cabinet or the power The built-in gas-filled surge arrester inside the device
supply as a stand-alone component is planned during final ensures that the power supply is effectively protected
inspection and testing, the following features must be against asymmetrical disturbance variables (e.g., EN
observed. 61000-4-5).
– The power supply wiring must be implemented as Each surge voltage test represents a very high load for the
shown in the wiring diagram. power supply. Therefore avoid unnecessary loading or
– The maximum permissible test voltages must not be damage to the power supply due to excessive test voltages.
exceeded. If necessary, the gas-filled surge arrester inside the device
Avoid unnecessary loading or damage to the power supply can be disconnected in order to use higher test voltages.
due to excessive test voltages. Following successful completion of testing, please
reconnect the gas-filled surge arrester.
M3 C
NF
QUINT POWER
1
A x8
+ +
Output DC
B
UOut
29,5V
Signal
13
14
Rem
SGnd 2
Out 1
Out 2
24V
> 100% Boost
> 75% P
> 50% Out
DC OK
HV
3 Figure 2 Disconnect gas-filled surge arrester
/=
QUINT POWER
1 Uout
UOut
2 2 Signal
65
29,5V
13
14
Signal Ground
Rem
SGnd
Out 1
+ + Out 2
Output
Output DC 24V
24V 5A
5A 24V
> 100% Boost
130
> 75% Pout
> 50% POut
9 Uout
UOut
Signal
3 DC OK DC OK
29,5V
13
QUINT POWER
14
Signal Ground
Rem
SGnd NFC
Out 1
Out 2
24V
> 100%
100% Boost
Boost
> 75% Pout
> 50% POut 4 400-500 V
Input AC 100-240 V
DC OK DC OK N/- L/+
L1/ L2 L3/+
POWER
QUINTPOWER
7
QUINT
5
131
Input AC
Input AC 100-240V
400-500 V
N/- L/+ 125
L1/ L2 L3/+ 122
2 2
6
Figure 3 Operating and indication elements
Key
36
a a
b
+ +
Output
Output DC 24V
24V 5A
5A
Uout
UOut
29,5V Signal
13
14
Signal Ground
Rem
SGnd
Out 1
Out 2
24V
> 100% Boost
130
NFC
400-500 V
Input AC 100-240 V
N/- L/+
L1/ L2 L3/+
c
(+) +
active +
L
PFC
-
-
N
(-) 13
OVP 14
Rem
SGnd
Out 1
Out 2
C NFC
POut
Key
active
Power factor correction (PFC) Microcontroller
PFC
C
Switching transistor and main transmitter NFC interface (Near Field Communication)
NFC
(electrically isolating)
B
8.3.1 Disassembling the universal DIN rail adapter
Proceed as follows to disassemble the universal DIN rail
Figure 8 Snapping the power supply onto the DIN rail
adapter that comes pre-mounted:
8.2 Removing the power supply unit 1. Remove the screws for the universal DIN rail adapter
using a suitable screwdriver (Torx 10).
Proceed as follows to remove the power supply:
2. Separate the universal DIN rail adapter from the rear of
1. Take a suitable screwdriver and insert this into the lock the power supply.
hole on the universal DIN rail adapter (A).
2. Release the lock by lifting the screwdriver (B).
3. Carefully swivel the power supply forward (C) so that
the lock slides back into the starting position.
4. Then separate the power supply from the DIN rail (D).
8
M3x 8
M3x
8.3.2 Mounting the universal DIN rail adapter 8.4.1 Mounting the UWA 182/52 universal wall
adapter
To mount the universal DIN rail adapter on the left side of the
device, proceed as follows: Proceed as follows to disassemble the universal DIN rail
1. Position the universal DIN rail adapter on the left side of adapter that comes pre-mounted:
the housing so that the mounting holes are congruent 1. Remove the screws for the universal DIN rail adapter
with the hole pattern for the mounting holes. using a suitable screwdriver (Torx 10).
2. Insert the Torx screws that were removed earlier into the 2. Separate the universal DIN rail adapter from the rear of
appropriate hole pattern on the universal DIN rail the power supply.
adapter so that the necessary drill holes on the power 3. Position the universal wall adapter in such a way that
supply can be accessed. the keyholes or oval tapers face up. The mounting
3. Screw the universal DIN rail adapter onto the power surface for the power supply is the raised section of the
supply. universal wall adapter.
4. Place the power supply on the universal wall adapter in
The maximum tightening torque of the Torx the normal mounting position (input voltage connection
screw (Torx® T10) is 0.7 Nm. terminal blocks below).
5. Insert the Torx screws into the appropriate hole pattern
on the universal wall adapter so that the necessary
mounting holes on the power supply can be accessed.
6. Screw the universal wall adapter onto the power supply.
x8 x8
M3 M3
8
M3x 8
M3x
8.4.2 Mounting the UWA 130 2-piece universal wall 8.5 Fix connection wiring to the power supply
adapter
Two receptacles for the bundled attachment of the
Proceed as follows to disassemble the universal DIN rail connection wiring are integrated in the left and right housing
adapter that comes pre-mounted: panel. Use cable binders to secure the connection wiring
1. Remove the screws for the universal DIN rail adapter (optional PKB 140X3,6 - Order No. 1005460).
using a suitable screwdriver (Torx 10). Proceed as follows to secure the connection wiring:
2. Separate the universal DIN rail adapter from the rear of – Wire the power supply with sufficient connection
the power supply. reserve (input terminal blocks, output terminal blocks,
3. Position the universal wall adapter. The mounting signal terminal blocks)
surface for the power supply is the raised section of the – Bundle and set up the connection wiring so that the
universal wall adapter. cooling grilles on the top and bottom of the housing are
4. Place the power supply on the universal wall adapter in covered as little as possible.
the normal mounting position (input voltage connection – Thread the cable binders into the necessary
terminal blocks below). receptacles for the cable binders.
5. Insert the Torx screws into the appropriate hole pattern
on the universal wall adapter so that the necessary
mounting holes in the side flanges of the power supply
can be accessed.
6. Screw the two-piece universal wall adapter onto the
power supply.
U
Out
Sig
13 na
l
14
Re
m
SG
nd
Ou
t1
Ou
8 t2
M3x
M3x
8 >1
> 700%
> 55% Boo
DC0% P st
OK out
U
Out
Sig
13 na
l
14
Re
m
SG
nd
Ou
t1
Ou
t2
>1
> 700%
> 55% Boo
DC0% P st
OK out
– Shorten the excess length of the cable binder ends. 9 Device connection terminal blocks
– Then check again that the connection wiring is properly
secured. The AC input and DC output terminal blocks on the front of
the power supply feature screw connection technology. The
signal level is wired without tools by means of Push-in
connection technology.
9.1 Input
U
Out
Sig
13
14
Re
na
l The power supply is operated on single-phase AC systems
m
SG
Ou
Ou
nd
t1
t2
or two outer conductors of three-phase systems. The power
>1
> 700%
> 55% Boo
DC0% P st
supply is connected on the primary side via the INPUT L/N/
OK out
connection terminal blocks.
Figure 16 Shorten protruding ends of the cable binder
The power supply is approved for connection
to TN, TT, and IT power grids with a maximum
NOTE: Mechanical damage to the connection phase-to-phase voltage of 240 V AC.
wiring caused by friction
In extreme ambient conditions, e.g., strong
vibrations, protect the connection wiring TN-S TN-C
L L
against mechanical damage using additional N PEN
insulation material. The additional insulation PE
material for protecting the connection wiring is
limited to the area where the cable binders are
attached. N L N L
+ − + −
L1 L1
L2 L2
L3 L3
N PEN
PE
N L N L
+ − + −
TT iT
L L
PEN N
N L N L
+ − + −
L1 L1
L2 L2
L3 L3
N
N L N L
+ − + −
Input DC 110...250 V
+ +
-
PE
N/- L/+
+ -
M
Keeps temperatures
Loads with high inrush Selective tripping of
Application Normal load System extension
current
Energy storage charging
fuses
low in the event of Short circuit, non-fused
faults
Characteristics
U/I Advanced -
Smart HICCUP - -
FUSE MODE - - -
Symbol Designation
Suitable for the application
- Not suitable for the application
10.1 U/I Advanced output characteristic curve 10.2 Smart HICCUP output characteristic curve
The preset U/I Advanced output characteristic curve is The SMART HICCUP output characteristic curve keeps the
optimized for the following applications: thermal load of the connecting cables at a low level in the
– For selective tripping of standard circuit breakers (SFB event of a sustained overload. If loads are not protected or
technology). The power supply supplies up to 6 times are protected in a way that is not permitted, the loads are
the nominal current for 15 ms. Loads connected in supplied for 2 s. The DC output of the power supply is then
parallel continue working. switched off for 8 s. This procedure is repeated until the
– When supplying loads with high switch-on currents, cause of the overload has been remedied.
such as motors. The dynamic boost of the power supply The preset Smart HICCUP output characteristic curve is
supplies up to 200% of the nominal power for 5 s. This optimized for the following applications:
ensures that sufficient reserve energy is available; – If only a low short-circuit current is permitted.
overdimensioning of the power supply is not necessary. – If following an overload or short circuit the output
– For system extension. With the static boost, up to voltage should be made available again automatically.
125% of the nominal output power is available for a
sustained period (up to 40°C).
UOut [V]
UN
– For fast energy storage charging (e.g., of batteries) to 5s
supply a wide range of loads. The power supply
operates in the nominal operating range. Energy supply UN
to the load is ensured. 2
UOut [V]
UN
5s
0 IN IStat. Boost
100% 125% 200%
UN
3
IOut [A]
0 IN IStat. Boost
100% 125% 200% IDyn. Boost 2s
IOut [A]
0
5s t [s]
IDyn. Boost
Figure 21 Smart HICCUP output characteristic curve
0
t [s]
IFuse
0
tFuse
t [s]
M3
x8 C
QUINT POWER
NF
NFC
DAT
CONN
POut [W]
In order to configure the power supply via the NFC interface, PDyn. Boost 200%
the following hardware and software requirements must be
met:
PStat. Boost 125%
– NFC-capable mobile terminal device with Android PN 100%
operating system as of Version 4.1.x (Jelly Bean) 75%
– QUINT POWER app (Google Play Store)
phoenixcontact.net/webcode/#0852
to configure and order your power supply.
tDyn.Boost tDyn.Boost
IDyn.Boost
tPause
IBase Load
t [s]
Use the following tables to determine the required recovery 12.2.3 Example: Determining the recovery time
time (tPause) at the maximum dynamic boost current (IDyn. (tPause)
Boost) based on the following values: At an output current (IBase Load) of 2 A, the dynamic output
– IBase Load current (IDyn. Boost) of 10 A increases for 2 s (tDyn. Boost).
– Duration of the boost current (tDyn. Boost) After a recovery time (tPause) of 2.3 s, the dynamic boost is
– Ambient temperature (40 °C or 60 °C) available once again.
If a current that is lower than the maximum IBase Load IDyn. Boost tDyn. Boost [s]
available dynamic boost current (IDyn. Boost) is
[A] [A] 1 2 3 4 5
required for the same period, the recovery
time may (tPause) decrease. 0 10 1 2 3,1 4,1 6
tPause [s]
3 10 1,3 2,6 3,8 6 7
2 10 1,1 2,3 3,4 4,5 6 Figure 29 Example recovery time for ≤ 40°C
tPause [s]
4 10 1,7 3,4 5 7 9
5 10 2,9 6 9 12 15
0 10 2,9 6 9 12 15
1 10 2,9 6 9 12 15
tPause [s]
2 10 3,3 7 10 14 17
3 10 4,1 9 13 17 21
4 10 7 14 20 27 33
5 10 32 63 94 125 157
The U/I Advanced output characteristic curve Figure 31 Schematic diagram of the maximum cable
supports SFB technology. length
6x IN
typ. 3 - 5 ms
IN
0
t [s]
Maximum distance l [m] with device circuit breaker Conductor cross section
A [mm²] 0.75 1.0 1.5 2.5
AWG 18 (17) 16 14
Phoenix Contact CB TM1 1A SFB P 27 36 54 91
CB TM1 2A SFB P 10 13 20 34
Tripping: magnetic
DC correction factor (0 Hz): Phoenix Contact = 1,0
Characteristics: C
Characteristic C (10 times the rated current) x correction factor
Ambient temperature: +20 °C
Internal resistance Ri of the device circuit taken into consideration
breaker:
Comments: In addition to the short-circuit current, the power supply unit also supplies
half the nominal current for load paths connected in parallel.
Tripping: magnetic
DC correction factor (0 Hz): Siemens = 1.4; ABB = 1.5
Characteristics: A, B, C, Z
Characteristic A (3 times the rated current) x correction factor
Characteristic B (5 times the rated current) x correction factor
Characteristic C (10 times the rated current) x correction factor
Characteristic Z (3 times the rated current) x correction factor
Ambient temperature: +20 °C
Internal resistance Ri of the device circuit taken into consideration
breaker:
Comments: In addition to the short-circuit current, the power supply unit also supplies
half the nominal current for load paths connected in parallel.
Maximum distance l [m] with fuse Melting integral I²t Conductor cross section
[A²s]
A [mm²] 0.75 1.0 1.5 2.5
AWG 18 (17) 16 14
Cooper Bussmann GMA 1A 0.48 48 64 97 162
GMA 1.25A 0.84 36 48 72 120
GMA 1.5A 1.6 19 25 38 64
GMA 1.6A 2 15 20 31 51
GMA 2A 3.1 9 13 19 33
GMC 1A 1.8 15 20 31 52
GMC 1.25A 3.4 8 11 16 27
Tripping: thermal
Characteristics: Cooper Bussmann GMA (fast-blow - fast acting)
Cooper Bussmann GMC (medium-blow - medium time delay)
Ambient temperature: +20 °C
Internal resistance Ri of the fuse: taken into consideration
Comments: In addition to the short-circuit current, the power supply unit also supplies
half the nominal current for load paths connected in parallel.
Key
Figure 35 Signaling
Figure 33 Signaling
Signal
PLC
13 Digital Input
14
Rem
SGnd GND
Out 1 DI x 0/24 V DC
Out 2 DI x 0/24 V DC
Figure 34 Signaling
QUINT POWER default settings upon delivery Out 1 Out 2 Relay 13/14 Out 2
digital digital floating analog
0/24 V DC 0/24 V DC 24 V DC / ≤ 1 A 4 ... 20 mA
20 mA 20 mA 30 V AC / ≤ 0.5 A
Output voltage ① 25 ... 135 % Default Default ① 0 ... 32 V DC
V ② 90 % ② 0 ... 30 V DC
Key
Symbol Description
① Setting range
② Default setting of the standard item
Default Configuration set upon delivery
Configuration that can be selected
-- Configuration that cannot be selected
The simultaneous control of multiple signal outputs by means of one signal option is possible, as is the use of logic operations
to link multiple signal options to one control. The power supply is configured using the QUINT POWER software or the QUINT
POWER app.
14.3 Description of signaling is true if a control cabinet fan or cooling system fails. In the
event of any form of overtemperature, the power supply
14.3.1 Output voltage provides a warning by means of this signal, well before the
Signals whether the output voltage is in the preset range. If supply of the loads is in any danger.
the output voltage of the power supply falls below the set Specifications regarding the available output power (see
threshold value, the signal state changes. derating section).
Example of use
For systems with a very long operating time, such as wind
turbine generators or refineries, maintenance intervals are
planned. You can even schedule the maintenance date
during configuration based on the ambient temperature and
utilization of the power supply.
Example of use
Outdoor control cabinets can reach a high internal
temperature depending on the position of the sun. The same
14.4 Remote input When using a PLC output, select the following external
circuit version to switch the power supply to SLEEP MODE.
The power supply is switched on and off using the digital
remote input of the power supply. When switched off, power
transmission is deactivated on the DC output side of the Signal a)
PLC
PNP output
power supply. The load connected to the DC output terminal 13 < 1 k
Gnd
blocks is no longer supplied with energy. The operating 14
mode where the DC output side is deactivated is called
Rem
SLEEP MODE.
SGnd
To switch the power supply to SLEEP MODE, select one of Out 1 PLC
the external circuit versions below. The external circuit is b)
Out 2 NPN output
wired between signal terminal blocks Rem (remote input) Gnd
and SGnd (signal ground).
Figure 38 External wiring versions with PNP and NPN
Signal a) < 15 k output
13
14.5 LED status indicators
14
Rem Four LED status indicators are integrated in the front of the
SGnd power supply, which indicate the current device state.
Out 1 b) The green DC OK LED indicates the current status of the
Out 2 output voltage (UOut). The DC OK LED is permanently on as
long as the value of the output voltage UOut is ≥ 0.9 x USet. If
the value of the output voltage is < 0.9 x USet, the green
Figure 36 External wiring versions, enable DC OK LED flashes.
SLEEP MODE Depending on the required output power of the connected
load, the three POut LEDs, which indicate the current output
To switch the power supply back on, select one of the power, light up. Assuming that the provided output power is
following external circuits between signal terminal blocks > 50% of the nominal output power, the > 50% LED lights
Rem and SGnd. Power transmission inside the device is up green. If the demanded power continues to increase until
activated again. As usual, the energy for supplying the loads it is above 75%, the > 75% LED lights up green in addition
is available at the DC output terminal blocks. to the > 50% LED. If the required output power is then
greater than the nominal device power, the power supply
Signal a) < 40 k operates in boost mode. In boost mode, the > 100% LED
13 additionally lights up yellow.
14
Rem
SGnd
Out 1 b)
Out 2
Signal Out 2: POut < PN Default Active High Active Low Active Low
LED: DC OK
Signal Out 2: POut < PN Default Active High Active Low Active Low
LED: DC OK
Signal Out 2: POut < PN Default Active High Active Low Active Low
LED: DC OK
14.10.1 Surge protection for the high-voltage area at the power plant
Surge protection (Phoenix Contact Order No.: 2905223 or comparable protection) must be implemented for power plant
applications when using signal connection types t (telecommunications area), h (high voltage area) or f (field) in accordance
with IEC/EN 61850-3 or signal connection types 3 (process area) and 4 (high voltage area) in accordance with EN 61000-6-5.
When using the digital signals, a relay (Phoenix Contact Order No.: 2900299 or a comparable relay) can be implemented.
Uout
Signal
13
PLC
14
Rem Digital Input
Sgnd
5 6
Out 1 DI x 0/24 V DC
Out 2
1 2
> 100% Boost GND
> 75% 3 4
> 50% POut
DC OK
Uout
Signal
13
PLC
14
Rem 11/13(+)
Digital Input
A2-
Sgnd DI x 0/24 V DC
Out 1
Out 2
A2 11
> 100% Boost A1+ 14
A1 14 GND
> 75%
> 50% POut 12
DC OK
Σ = IN
+48 V -48 V + −
+ −
Σ = IN
+
−
Σ = IN
Figure 47 Schematic diagram, redundant operation with
QUINT S-ORING
POut [%]
temperature of > 60 °C, a power derating of 2.5 %/K should
be observed. Up to an ambient temperature of 40 °C, the
200
175
power supply can take power from the static boost for a
sustained period. In the 40 °C to 60 °C temperature range,
150
125
the power supply can output more than the nominal power 100
for a sustained period. 75
50 = PN 100 % 60 °C
= PStat. 125 % 40 °C
POut [W]
25
PDyn. Boost = PDyn. 200 % 60 °C
200% 0
0 1000 2000 3000 4000 5000
-25 40 60 70
TA [°C]
Derating 1 %/V
UIn TA IOut UOut
< 100 V AC
≤ 60 °C IN
< 110 V DC
24 V DC
< 115 V AC
≤ 40 °C IStat. Boost
< 110 V DC
The power supply should be mounted horizontally for heat dissipation reasons (AC connection terminal blocks
facing downward). Please observe the derating for any mounting other than the normal mounting position.
Reduce the output power based on the prevailing ambient temperature.
The recommended output power for different mounting positions and ambient temperatures can be found in the
characteristic curves below.
Exceeding these values will reduce the service life of the power supply.
225
POut [%] 200
175
150
125
U
29Out
,5V
13
Sig
na
100
l
14
Re
SG
m
nd 75
= PN 100 %
Ou
24 t1
V Ou
50
t2
>1
> 00%
> 575% Boo
DC0% P st = PStat. 125 %
OK out
25
= PDyn. 200 %
0
QUINT POWER
NF
C
-25 0 10 20 30 40 50 60 70
Y
T [°C]
Z
225
POut [%]
200
175
150
125
100
75
= PN 100 %
50
Signal
= PStat. 125 %
25
= PDyn. 200 %
> 100% Boost
13
14
Rem
Out 1
0
Out 2
> 75%
DC OK
-25 0 10 20 30 40 50 60 70
24V
NFC
Y R
OW
E
TP
T [°C]
IN
QU
Z
225
POut [%]
200
175
150
125
100
QUINT POWER
C
NF
75
50 = PN 100 %
OK out = PStat. 125 %
DC0% P st
25
= PDyn. 200 %
> 55% Boo
> 700%
>1
2
V Out
Ou d
t1 24
0
SG
Re
14
n
m -25 0 10 20 30 40 50 60 70
Y l
na
Sig
13
T [°C]
,5V
29
Out
U
225
POut [%]
200
175
150
125
QU
IN
100
TP
OW
75
M
E
3x
R
= PN 100 %
8
50
= PStat. 125 %
NFC
DC OK
25
> 50% Pout
= PDyn. 200 %
24V
> 75%
> 100% Boost
Out 2
0
Out 1
SGnd
29,5V
Rem
UOut
14
13
-25 0 10 20 30 40 50 60 70
Signal
Y
T [°C]
Z
225
POut [%]
200
175
150
125
100
75
= PN 100 %
50
= PStat. 125 %
25
= PDyn. 200 %
0
-25 0 10 20 30 40 50 60 70
Y
T [°C]
Z
ut
OK Po ost
225
POut [%]
o
DC 50%5% % B
> > 7 00
u >1 t2
V O Out 1 d
n
SG em
24
200
M3x8
l
na R 14
Sig
13
,5V
175
ut
29 U
O
150
125
100
75
= PN 100 %
50
= PStat. 125 %
25
= PDyn. 200 %
0
-25 0 10 20 30 40 50 60 70
Y
T [°C]
Z