This document provides technical data about an ABC Tile Adhesive Heavy-Duty cement-based adhesive for bonding tiles. It lists information about the product name, description, advantages, colors, standards, and specifications. Application instructions specify dampening surfaces, using a notched trowel to apply a thin layer, installing tiles within 20 minutes, and allowing 24 hours before foot traffic.
This document provides technical data about an ABC Tile Adhesive Heavy-Duty cement-based adhesive for bonding tiles. It lists information about the product name, description, advantages, colors, standards, and specifications. Application instructions specify dampening surfaces, using a notched trowel to apply a thin layer, installing tiles within 20 minutes, and allowing 24 hours before foot traffic.
This document provides technical data about an ABC Tile Adhesive Heavy-Duty cement-based adhesive for bonding tiles. It lists information about the product name, description, advantages, colors, standards, and specifications. Application instructions specify dampening surfaces, using a notched trowel to apply a thin layer, installing tiles within 20 minutes, and allowing 24 hours before foot traffic.
This document provides technical data about an ABC Tile Adhesive Heavy-Duty cement-based adhesive for bonding tiles. It lists information about the product name, description, advantages, colors, standards, and specifications. Application instructions specify dampening surfaces, using a notched trowel to apply a thin layer, installing tiles within 20 minutes, and allowing 24 hours before foot traffic.
COMPANY INFORMATION Caution: Use only non-absorptive materials as mixing base (plastic pail or G.I. sheet). If absorptive materials such as plywood, wooden box, gypsum board, ALLGEMEINE BAU - CHEMIE PHIL., INC. fiber cement board or cardboard is used, it will affect the chemical properties of the product, which can result in bonding failure and poor product performance. Address: 10/F Asian Star Building, 2404 Asean Drive, 2. Application Notched Fi l i n v e s t C i ty, A l a b a n g , M u n ti n l u p a C i ty 1 7 8 1 P h i l i p p i n e s Dampen concrete surface before application. Using a notched Trowel Tel: (+63 2) 88426891 Fax: (+63 2) 88427146 info@abc.ph www.abc.ph trowel, spread mortar in horizontal straight direction to produce a ribbed thin bed. Apply evenly over an area of 1m2 at a time . For large PRODUCT NAME format tiles or stoneware, apply tile adhesive on two surfaces (on the substrate and at the back of the tile or stone to be installed). ABC TILE ADHESIVE Heavy-Duty Tile Size Tile Adhesive Thickness PRODUCT DESCRIPTION Mosaic ABC TILE ADHESIVE Heavy-Duty is a is a cement-based adhesive designed for below 30 x 30cm 3mm (Thin bed) bonding all types of tiles for floor & wall tile installations. Application areas include indoor & Small outdoor concrete surfaces using the thinbed method. ABC TILE ADHESIVE HEAVY- DUTY is primarily used for low porosity tiles, glass mosaic tiles, stoneware & Medium 60 x 60cm & below 6mm (Medium bed) all types of large format tiles. It is highly recommended for outdoor tiling, pool & water features & all heavy-foot traffic areas. Large above 60 x 60cm 10mm (Thick bed)
THE ABC TILE ADHESIVE HEAVY-DUTY ADVANTAGE 3. Installation Open Time
Install tiles within the open time of 20 minutes. During the open Extra Strong bonding time, the mortar’s adhesive strength is most effective. Adjust High Pull-out Strength and align tiles. Use a rubber mallet to apply pressure on the tiles Resistant to Thermal FRIENDLY & assure proper bonding. Ready for foot traffic after 24 hours. Deformation TIPS: Withstands structural movements Do random checks if the back of the tiles are fully covered with Fast & Easy Installation tile adhesive. Foot Traffic Stays flexible Check if tile adhesive mortar still adheres to your finger to find Economical Eco-friendly & Low VOC Levels out if the open time has not lapsed. If open time has lapsed, remove old tile adhesive layer and reapply a new one to avoid after hours 24 bonding failure. COLORS NEVER add newly prepared tile adhesive to a previously mixed batch. Gray & White Use tile spacers for uniform grout lines. A tile joint width is needed to accommodate possible tile movement due to thermal deformation, CLASSIFICATION STANDARD substrate shrinkage or tile expansion, thus preventing the tile from cracking. ANSI A118.1 (USA) American National Standards Institute SECTIONAL DETAIL EN 12004 : 2000 (EU) European Standard PNS ISO 13007 - 1:2014 Type C2 (PH) Philippine National Standards International Organization for Standardization Note: Application thickness is dependent TECHNICAL DATA on the levelness of the surface to be tiled. Physical Test PNS ISO 13007-1:2014 Results wall
Water demand Not Applicable 20 ml / 100 g
Tile joint Workability Not Applicable Excellent (min. width = 2mm)
Open time > 20 minutes 20 minutes
Pot life Not Applicable 4 hours tile Standing strength Not Applicable Excellent concrete floor slab Slip resistance < 0.5 mm 0 mm Tensile adhesion strength > 1.0 N/mm2 2.5 N/mm2 COVERAGE Tensile adhesion strength > 1.0 N/mm 2 2.0 N/mm 2
Application Thickness Coverage The surface must be fully cured, structurally stable, level, even, clean & free Thin bed 3mm 5m2 from paint & contaminants such as dirt, dust, loose material, oil and chemicals. Use a level bar to ensure the surface’s levelness and / or plumbness. Medium bed 6mm 2.6m2 For painted surfaces: acid etch or abrade paint to ensure proper bonding. Thick bed 10mm 1.6m2 For water exposed areas: use ABC Aquashield Plus Flexible Waterproofing before tiling. Note: Coverage is dependent on tile size, surface smoothness of the back of the tile, substrate condition & application thickness. The bigger the tile, the smaller the coverage area. APPLICATION GUIDE 1. Mixing PACKAGING Use plastic pail as mixing base. Pour water into container Potlife 5 kg plastic bag and 25 kg multilayer paperbag and add ABC TILE ADHESIVE Heavy-Duty that can be used within the pot life of 4 hours. POT LIFE is the time during which the mix can be used. Using a mixing torque, stir to attain hours 4 STORAGE & SHELF LIFE When stored in a cool dry place & in its original unopened packaging, ABC Tile smooth, lump-free and pasty consistency. Let it rest for 15 minutes and Adhesive Heavy-Duty will remain usable one year from date of manufacture. restir briefly before use. WARRANTY Mixing Ratio Mixing Method Mixing Tool for best Due to variety of applications, different working methods and the various properties of Water + Tile Adhesive bases, we cannot assume responsibility or liability with regard to the application of our results: products. Our guarantee and liability are restricted to the quality of our products at the 5.50L + 25kg Mechanical mixing torque use mixing time of acceptance of the customer of such products. In no case shall our liability extend beyond replacement of defective products, if any, found at the time of 6.25L + 25kg Manual mason’s trowel torque acceptance. For all deliveries and services, our General Sales Condition including warranties stipulated for each case are valid.
INNOVATIVE BUILDING SOLUTIONS
DISCLAIMER: All information on this technical data sheet is for general guidance only. ABC Phil., Inc. reserves the right to change specifications without prior notice. Refer to latest version at www.abc.ph MC - 03/20