Published Document Recommendations For The Design of Structures To BS EN 1991-1-1
Published Document Recommendations For The Design of Structures To BS EN 1991-1-1
Published Document Recommendations For The Design of Structures To BS EN 1991-1-1
PUBLISHED DOCUMENT
Publication history
First published May 2011
Contents
Foreword ii
Introduction 1
1 Scope 1
2 Imposed loads on floors for areas of industrial use and other work area
use 1
3 Vertical loads on partition walls and parapets 1
4 Uniformly distributed and concentrated loads applicable to infills for walls
and parapets 1
Bibliography 4
List of tables
Table 1 – Imposed loads on floors for areas of industrial use and other work
area use 2
Table 2 – Uniformly distributed and concentrated loads applicable to infills for
walls and parapets – To be read with BS EN 1991-1-1:2002, Table NA.8 3
Summary of pages
This document comprises a front cover, an inside front cover, pages i to ii,
pages 1 to 4, an inside back cover and a back cover.
© BSI 2011 • i
PD 6688-1-1:2011 PUBLISHED DOCUMENT
Foreword
Publishing information
This Published Document has been prepared by BSI Subcommittee B/525/1. It is a
background paper that gives non-contradictory complimentary information for
use in the UK with the Eurocode BS EN 1991-1-1:2002 and its UK National
Annex.
This Published Document is published by BSI and came into effect on 31 May
2011. It was prepared by Subcommittee B/525/1, Actions (loadings) and basis of
design, under the authority of Technical Committee B/525, Building and civil
engineering structures. A list of organizations represented on this committee
can be obtained on request to its secretary.
Presentational conventions
The provisions in this Published Document are presented in roman (i.e. upright)
type. Its recommendations are expressed in sentences in which the principal
auxiliary verb is “should”.
Commentary, explanation and general informative material is presented in
smaller italic type, and does not constitute a normative element.
The word “should” is used to express recommendations of this Published
Document. The word “may” is used in the text to express permissibility, e.g. as
an alternative to the primary recommendation of the clause. The word “can” is
used to express possibility, e.g. a consequence of an action or an event.
Notes and commentaries are provided throughout the text of this Published
Document. Notes give references and additional information that are important
but do not form part of the recommendations. Commentaries give background
information.
ii • © BSI 2011
PUBLISHED DOCUMENT PD 6688-1-1:2011
Introduction
When there is a need for guidance on a subject that is not covered by the
Eurocode, a country can choose to publish documents that contain
non-contradictory complimentary information that supports the Eurocode. This
Published Document provides just such information and has been cited as a
reference in the UK National Annex to BS EN 1991-1-1:2002.
1 Scope
This Published Document is a background paper that gives non-contradictory
complementary information for use in the UK with BS EN 1991-1-1:2002 and its
UK National Annex.
This Published Document gives non-contradictory complementary information
relating to imposed loads on floors for areas of industrial use and other work
area use.
© BSI 2011 • 1
PD 6688-1-1:2011 PUBLISHED DOCUMENT
Table 1 Imposed loads on floors for areas of industrial use and other work area use
2 • © BSI 2011
Table 2 Uniformly distributed and concentrated loads applicable to infills for walls and parapets – To be read with BS EN 1991-1-1:2002,
Table NA.8
B and C1 (iii) Areas not susceptible to overcrowding in office and institutional 1,0 0,5
(including buildings, reading rooms and classrooms including stairs
sub-categories in Table (iv) Restaurants and cafes 1,5 1,5
NA.2)
C2, C3, C4 and D (v) Areas having fixed seating within 530 mm of the barrier, 1,5 1,5
(including balustrade or parapet
sub-categories in Table (vi) Stairs, landings, balustrades, corridors and ramps 1,0 0,5
NA.2)A) (vii) External balconies and edges of roofs 1,0 0,5
Footways within building curtilage and adjacent to
basement/sunken areas
(viii) All retail areas 1,5 1,5
C5 (ix) Footways or pavements less than 3 m wide adjacent to sunken 1,5 1,5
(including areas
sub-categories in Table (x) Theatres, cinemas, discotheques, bars, auditoria, shopping malls, 1.5 1,5
NA.2) assembly areas, studios. Footways or pavements greater than
3 m wide adjacent to sunken areas
(xi) Grandstands and stadia See requirements of the appropriate
certifying authority
E (xii) Industrial; and storage buildings except as given by (xiii) 1,0 0,5
(including and (xiv)
sub-categories in Table (xiii) Light pedestrian traffic routes in industrial and storage buildings 0,5 0,25
NA.4) except designated escape routes
(xiv) Light access stairs and gangways not more than 600 mm wide N/A N/A
F and G (xv) Pedestrian areas in car parks including stairs, landings, ramps, 1,5 1,5
edges or internal floors, footways, edges of roofs
(xvi) Horizontal loads imposed by vehicles See BS EN 1991-1-1:2002, Annex B
© BSI 2011
•
A)
For areas where large crowds might occur, see C5.
3
PD 6688-1-1:2011
PD 6688-1-1:2011 PUBLISHED DOCUMENT
Bibliography
For dated references, only the edition cited applies. For undated references, the
latest edition of the referenced document (including any amendments) applies.
BS EN 1991-1-1:2002, Eurocode 1: Actions on structures – Part 1-1: General
actions – Densities, self weight, imposed loads for buildings
NA to BS EN 1991-1-1:2002, UK National Annex to Eurocode 1: Actions on
structures – Part 1-1: General actions – Densities, self weight, imposed loads for
buildings
4 • © BSI 2011
This page deliberately left blank
NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW
About us Revisions
We bring together business, industry, government, consumers, innovators Our British Standards and other publications are updated by amendment or revision.
and others to shape their combined experience and expertise into standards We continually improve the quality of our products and services to benefit your
-based solutions. business. If you find an inaccuracy or ambiguity within a British Standard or other
The knowledge embodied in our standards has been carefully assembled in BSI publication please inform the Knowledge Centre.
a dependable format and refined through our open consultation process.
Organizations of all sizes and across all sectors choose standards to help Copyright
them achieve their goals. All the data, software and documentation set out in all British Standards and
other BSI publications are the property of and copyrighted by BSI, or some person
Information on standards or entity that owns copyright in the information used (such as the international
We can provide you with the knowledge that your organization needs standardization bodies) and has formally licensed such information to BSI for
to succeed. Find out more about British Standards by visiting our website at commercial publication and use. Except as permitted under the Copyright, Designs
bsigroup.com/standards or contacting our Customer Services team or and Patents Act 1988 no extract may be reproduced, stored in a retrieval system
Knowledge Centre. or transmitted in any form or by any means – electronic, photocopying, recording
or otherwise – without prior written permission from BSI. Details and advice can
Buying standards be obtained from the Copyright & Licensing Department.
You can buy and download PDF versions of BSI publications, including British
and adopted European and international standards, through our website at Useful Contacts:
bsigroup.com/shop, where hard copies can also be purchased. Customer Services
If you need international and foreign standards from other Standards Development Tel: +44 845 086 9001
Organizations, hard copies can be ordered from our Customer Services team. Email (orders): orders@bsigroup.com
Email (enquiries): cservices@bsigroup.com
Subscriptions
Subscriptions
Our range of subscription services are designed to make using standards
Tel: +44 845 086 9001
easier for you. For further information on our subscription products go to
Email: subscriptions@bsigroup.com
bsigroup.com/subscriptions.
With British Standards Online (BSOL) you’ll have instant access to over 55,000 Knowledge Centre
British and adopted European and international standards from your desktop. Tel: +44 20 8996 7004
It’s available 24/7 and is refreshed daily so you’ll always be up to date. Email: knowledgecentre@bsigroup.com
You can keep in touch with standards developments and receive substantial
Copyright & Licensing
discounts on the purchase price of standards, both in single copy and subscription
format, by becoming a BSI Subscribing Member. Tel: +44 20 8996 7070
Email: copyright@bsigroup.com
PLUS is an updating service exclusive to BSI Subscribing Members. You will
automatically receive the latest hard copy of your standards when they’re
revised or replaced.
To find out more about becoming a BSI Subscribing Member and the benefits
of membership, please visit bsigroup.com/shop.
With a Multi-User Network Licence (MUNL) you are able to host standards
publications on your intranet. Licences can cover as few or as many users as you
wish. With updates supplied as soon as they’re available, you can be sure your
documentation is current. For further information, email bsmusales@bsigroup.com.