PG 740 PII Programming Device

Product Information Bulletin

This leaflet gives you specific
technical information on your
PG 740 PII programming device.
Safety Guidelines This product information bulletin contains notices which you should observe to ensure your own
personal safety, as well as to protect the product and connected equipment. These notices are
highlighted in the manual by a warning triangle and are marked as follows according to the level of
danger:

Warning
! indicates that death, severe personal injury or substantial property damage can result if proper
precautions are not taken.

Caution
! indicates that minor personal injury or property damage can result if proper precautions are not taken.

Note
draws your attention to particularly important information on the product, handling the product, or to
a particular part of the documentation.

Correct Usage Please observe the following:

Note
You can set up and operate your programming device in conjunction with the following instructions.
You should only connect external devices and work with memory cards in conjunction with the
PG 740 PII manual.
Only qualified personnel should be allowed to install and work on this equipment using the
PG 740 PII manual. Qualified persons are defined as persons who are authorized to commission, to
ground, and to tag equipment, systems, and circuits in accordance with established safety practices
and standards.

Warning
! This device may only be used for the applications described in the catalog or technical description,
and only in connection with devices or components from other manufacturers which have been
approved or recommended by Siemens.
This product can only function correctly and safely if it is transported, stored and set up carefully and
correctly, and operated and maintained as recommended.

Trademarks SIMATICR, SIMATIC NETR and SIMATIC HMIR are registered trademarks of Siemens AG.

Copyright E Siemens AG 1998 All Rights Reserved Liability Disclaimer

The reproduction, transmission, or use of this document or its contents is We have checked the contents of this document for agreement with the
not permitted without express written authority. Offenders will be liable for hardware and software described. Since deviations cannot be precluded
damages. All rights, including rights created by patent grant or registration entirely, we cannot guarantee full agreement. However, the data in this
of a utility model or design, are reserved. document are reviewed regularly and any necessary corrections included
in subsequent editions. Suggestions for improvement are welcomed.
E Siemens AG 1998
Siemens AG Technical data subject to change.
Bereich Automatisierungs- und Antriebstechnik
Geschaeftsgebiet Industrie-Automatisierungssysteme
Postfach 4848, D-90327 Nuernberg
Siemens Aktiengesellschaft C79000-Z7076-C748
Printed in the Fed. Rep. of Germany
FCC approval for USA and Canada

Federal Communications Commission

Radio Frequency Interference Statement
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.

Shielded Cables
Shielded cables must be used with this equipment to maintain compliance with FCC
regulations.

Modifications
Changes or modifications not expressly approved by the manufacturer could void the
user’s authority to operate the equipment.

Conditions of Operations
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.

Canadian Notice
This equipment does not exceed the Class A limits for radiated emissions as described
in the Radio Interference Regulations of the Canadian Department of
Communications.

Avis Canadien
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les
limites applicables aux appareils numériques de la Classe A prescrites dans le
Réglement sur le brouillage radioélectrique édicté par le Ministère des
Communications du Canada.

PG 740 PII Product Information Bulletin

C79000-K7076-C748-01 1
Setting Up and Transporting the PG 740 PII

Unpacking the Unpack your PG 740 PII programming device as follows:

PG 740 PII
1. Remove the packing.
2. Do no throw the original packing away. Keep it in case you have to
transport the unit again sometime in the future.
3. Check with the packing list to make sure no components are missing.
4. Check the packing and its contents for any shipping or transport damage.
5. Please inform your local dealer of any shipping or transport damages and
of outstanding items indicated on the packing list.
If your device has been stolen and repair work is required, the repair and
maintenance centers can only identify it by its serial number.
Enter the serial number of your programming device in the table below. You
can find this number on the type label attached to the base of the device.

Serial number
PG 740 PII

Desk-Top The PG 740 PII is mostly mounted on a desk or table top. To make working
Mounting with the PG 740 PII easier, it can be adapted as follows to the particular
workplace.
Set up your programming device as follows:
1. Set the PG 740 PII down on the desk or the table top.
2. Open the keyboard lock by pulling up the anthracite-colored handle.
3. Swing the keyboard down into position.

Handle

PG 740 PII Product Information Bulletin

2 C79000-K7076-C748-01
Changing the With the keyboard open, you can incline the unit to any angle between 0 and
Angle of 90° around the axis of rotation of its stand. Proceed as follows:
Inclination
1. Swing the keyboard down.
2. Pull the extra support out of the rear of the stand.
3. Incline the unit to the angle you prefer.

Caution
! Risk of injury!
There is a danger of the unit tipping over if it is set up without extra support
and at an angle of inclination of more than 15°. This could lead to personal
injury and also damage to the unit.
If the angle of inclination is greater than 15°, you must use the extra
slide-out support in the stand.

Preparatory The PG 740 PII is easy to transport. Before transporting it, however, you
Measures should take the following measures:
1. Switch the PG 740 PII off and wait approx. 20 seconds.
2. Then, unplug all connecting cables.
3. Close the covers protecting the ports and connections on the right-hand
and left-hand casing side panels.
4. Bring the unit into an upright position.
5. Swing the keyboard up and press it against the front plate of the unit.
Make sure that the latches on the left and the right sides snap into place.
6. Use the carrying handle if you only intend transporting the unit over a
short distance.
7. If you are transporting the PG 740 PII over large distances, pack the unit
with all its accessories in the carrying bag supplied.

PG 740 PII Product Information Bulletin

C79000-K7076-C748-01 3
Transport Despite the fact that the PG 740 PII is of rugged design, its internal
components are sensitive to severe vibrations or impact. You must therefore
protect your PG 740 PII against severe mechanical stressing when
transporting it.
Use the original packing material if you have to ship the PG 740 PII from
one location to another.

Caution
! Risk of mechanical damage!
Moisture or condensation in the unit can result in defects.
When transporting your PG 740 PII in cold weather when it may be exposed
to extreme variations in temperature, make sure that no moisture or
condensation can form on or in the unit.
The unit should be allowed to reach room temperature slowly before it is
started up. If condensation has formed, the unit should be left for about 12
hours (with a temperature difference of -20° C to +20° C (–4° F to +68° F))
before being switched on.

PG 740 PII Product Information Bulletin

4 C79000-K7076-C748-01
Hardware Components of the PG 740 PII

Front You can access all the important operator controls and displays from the front
or sides of the unit. The CD-ROM drive can be accessed from the underside
of the device.

Hold the on/off switch down for one second to 2

commission the device.
10 10

1
16 4
14
13
3 5

8
11
15 15

9
12

1 On/off switch for ON/Power Standby

2 Carrying handle
3 Display
16 LED displays
4 Ventilating slots
5 Coverplate for memory submodules, MEM
card PC-Card interface ports and floppy disk
drive 1)
6 Stand
7 Keyboard ON/Power Standby display 2)

8 Coverplate for interfaces: VGA, Hard disk/CD-ROM access

COM2, COM1, MPI/DP, LPT1/Printer, mouse1) Floppy disk access
9 Trackball Submodule programming
10 Catches for locking keyboard active
11 Pivot MPI, I/O port active
12 Protector strip
13 Socket for headphones
14 Socket for microphone
2) Power ON: green
15 Loudspeaker opening
Power Standby: red
1) The coverplates are used to protect the interface ports from dust, and can be
detached and snapped back on

PG 740 PII Product Information Bulletin

C79000-K7076-C748-01 5
 Note
You can use the On/off switch to switch to Power/Standby. You can connect
peripheral equipment to the PG 740 PII in this mode. When the network
connection is withdrawn, the device is completely without power.
If the device was switched off previously using the On/off key or via
Windows, it will remain in Power Standby mode when it is reconnected to
the power supply. If , however, the programming device was switched off by
pulling the network connector from its socket, the device will start up
automatically when reconnected to the power supply. To ensure that the
device switches off automatically when Windows is exited, set “Power OFF
Source Software” to Enabled in the BIOS Setup menu.

Left-Hand Casing All the connectors and interface ports for connecting to external devices are
Side Panel located on the left-hand side panel of the PG 740 PII (communications side).
(Communications
Side)
VGA port

On/off switch

Dummy plates
LED controls
covering
expansion slots
COM 2 port V.24

COM 1 port V.24

MPI/DP
CD-ROM drive

LPT 1/Printer
Power supply
connector socket
PS/2 mouse

Ports and Connectors Function

VGA port Connection for external monitor
COM 2 Connection for serial mouse
V 24/mouse
V.24/mouse
Serial port Connection for serial printer

COM 1 Connection for S5 programmable

V.24/MODEM/PLC controller
Serial port
MPI/DP Multipoint Interface (RS485)* Connection for S7 programmable
controller via a CP5611-compatible
MPI/DP interface
LPT 1 printer Connection for parallel printer
Parallel interface
PS/2 mouse Connection for external PS/2 mouse
Power supply connector socket Connection for power supply

* Galvanic isolation within the safety extra-low voltage circuit (SELV)

PG 740 PII Product Information Bulletin

6 C79000-K7076-C748-01
Power Supply Please note the following instructions when connecting your device to the
power supply.

Note
The power plug must be disconnected to isolate the unit completely from the
supply.
For operation in Canada and the USA, a CSA or UL-listed power supply
cable must be used.
For the United States and Canada:
In the United States and Canada the cord must be UL Listed and CSA
Labelled. The male plug is a NEMA 5-15 style.
For operation with 120 V:
Use a UL Listed, CSA Labelled Cord Set, consisting of a min. 18 AWG.
Type SVT or SJT three conductor flexible cord, max. 4.5 m (15 feet) in
length and a parallel blade grounding type attachment plug, rated 15 A, min
125 V.
For operation with 240 V (within the USA):
Use a UL Listed, CSA Labelled Cord Set, consisting of a min. 18 AWG.
Type SVT or SJT three conductor flexible cord, max. 4.5 m (15 feet) in
length and a tandem blade grounding type attachment plug, rated 15 A,
250 V.
For operation with 230 V (outside of USA):
Use a Cord Set consisting of a min 18 AWG cord and grounding type
attachment plug rated 15A, 250 V. The cord set should have the approviate
safety approvals for the country in which the equipment will be installed and
marked.
The unit is intended for operation with grounded power supply networks (TN
networks, VDE 0100 part 300 or IEC 364-3).
The unit is not intended for operation with non-grounded or
impedance-grounded systems (IT networks).
The Labeled Cord Set has to comply with the safety requirements of the
individual state.

VGA Port Please read the note referring to the operation of LC displays and external
monitors.

Note
The default setting of the display provides the simultaneous operation of a
LC display and an external monitor. The screen display is then optimized to
a format of 1024*768 pixels. Modes with a lower resolution and text modes
are expanded to this format.
To optimize the screen display for an external monitor, select “PG 740 PII
Hardware Options” under Setup and set “CRT/LCD selection: CRT
enabled”. A resolution of 1024*768 pixels with a higher refresh rate can then
be set.

PG 740 PII Product Information Bulletin

C79000-K7076-C748-01 7
Right-Hand Casing You access the slots for the S5 submodule interface, the memory card
Side Panel interface, the Cardbus / PC card interface, the disk drive, and the headphones
(Processing Side) and microphone connection from the right-hand side panel of the PG 740
PII’s casing (processing side).

Ventilating slots

Memory card interface

S5 submodule interface Microphone

Headphones

Ejector for Cardbus

/ PC cards Ejector for floppy disk

Cardbus / PC card
interface
3.5 in. floppy disk drive
Access LED

The following table contains an overview of the various interface ports and
connectors:
Interface Port Function
Programming port for S5 submodules Programming of SIMATIC S5
submodules
Programming port for memory cards Programming of SIMATIC memory cards
Cardbus / PC card port Connection for Cardbus / PC cards
Floppy disk drive Processing of 3.5 in. diskettes
Headphones and microphone Playback and recording

Ventilating Slots The raised air outlet slots for the ventilation are located above the interface
ports. There are also ventilating slots on the underside of the base. These
slots must not be covered and blocked in any way (by carpeting, for
instance).

Caution
! Risk of overheating!
If you cover up the slots for the inlet and outlet air in any way, there is a risk
that your PG 740 PII will be damaged.
Do not place any objects over, or lay them on, the ventilating slots.

PG 740 PII Product Information Bulletin

8 C79000-K7076-C748-01
Color Display of The PG 740 PII has a TFT (thin-film transistor) color display with a 13.3 in.
the PG 740 PII diagonal ([ 34 cm) and a maximum resolution of 1024 x 768 pixels (XGA).

Caution
! Risk of injury!
If a display is damaged, liquid crystal may escape. Do not touch this liquid
or allow it to come into contact with your skin in any way, and do not
breathe in the vapors. If you do come into contact with the liquid, wash
those parts of the skin affected immediately with alcohol, and rinse with
plenty of water. Then consult a physician right away.
Use only a cotton cloth and a neutral cleansing agent to clean the display. Do
not use water or aggressive solvents (like alcohol or acetone, for example).
Never touch the display with hard, pointed objects.

Drive Types The PG 740 PII is equipped with a 3.5 in. floppy disk drive, a 3.5 in. hard
disk drive, and a CD-ROM drive.

Disk Drive You can store programs and data on diskettes with the disk drive and load
them from diskettes into the PG 740 PII.

Types of Diskette You can use the following diskettes:

Double-Sided Double-Sided
High-Density Diskette Double-Density Diskette
3.5 in. 3.5 in.
1.44 Mbytes (135 TPI) 720 Kbytes
Programming device recognizes diskettes Programming device recognizes diskettes
by their coding by their coding

Handling Diskettes The diskette is inserted in the disk drive as shown below:
with the Floppy
Disk Drive
Ejector

Access LED

PG 740 PII Product Information Bulletin

C79000-K7076-C748-01 9
Hard Disk Drive Whenever the hard disk is accessed, the access LED on the front of the unit
lights up. You can find further information on page 11.

Caution
! Risk of loss of data and damage to the drive!
Drives are sensitive to vibrations and shock. Any vibrations occurring during
operation can lead to the loss of data or damage to the drive.
If you intend transporting the unit, switch it off, and wait until the drive has
come to rest (about 20 seconds) before you move it.

S5 Submodules Please note the following instructions while working with S5 submodules.

Caution
! Risk of damage to submodules!
If you plug the submodule in or take it out while its processing software is
running, there is a danger that it will be damaged.
You must not take out the S5 submodule as long as its LED is lit. You cannot
work simultaneously with S5 submodules and memory cards.
Before plugging in or taking out S5 submodules you must discharge the
electrostatic charge of your body by briefly touching a grounded object.
(ESD guideline).

Memory Cards Please note the following instructions while working with memory cards.

Caution
! When inserting cards, make sure that the orientation point is facing upwards.
Risk of damage to memory cards!
You must insert the memory card into a 68-pin connector with the type label
pointing to the rear of the unit.
If you try to plug the memory card in the wrong way around, your
programming device or memory card will be damaged!
You must not take out the memory card as long as its LED is lit. You cannot
work simultaneously with S5 submodules and memory cards.
Before plugging in or taking out memory cards you must discharge the
electrostatic charge of your body by briefly touching a grounded object.
(ESD guideline).

PG 740 PII Product Information Bulletin

10 C79000-K7076-C748-01
Cardbus / PC Proceed as follows while working with Cardbus / PC cards:
Cards
Caution
! Before inserting or removing Cardbus / PC cards, you must discharge the
electrostatic charge of your body by briefly touching a grounded object
(see ESD guidelines in the PG 740 PII manual). Otherwise faults could
occur.

Backup Battery A backup battery (3.6 V lithium battery) powers the hardware clock even
after the programming device is switched off.

Warning
! Risk of severe personal injury or property damage, danger of release of
harmful substances.
There may be a danger of explosion if the battery is not handled properly.
Incorrect disposal of used batteries can cause the release of harmful
substances.
Do not throw a new or discharged lithium battery into an open fire, do not
solder onto the cell container. Do not recharge the battery, do not open the
battery by force.
The correct lithium battery is available from Siemens (Order No.:
W79084-E1003-B1).
Return used batteries to the manufacturer/recycler or dispose of them
according to local regulations.

CD-ROM Drive The CD-ROM drive enables you to read CDs.

Opening the Swing the PG 740 PII into a horizontal position. The CD-ROM drive is now
Drawer on the underside of the programming device. By briefly pressing the eject
button, the drawer springs out slightly. Now pull the drawer out until it clicks
into position.

Inserting / When you first open the CD-ROM drive, you will find a transparent film
Removing CDs sheet in the drawer, to protect the drive during transport. Remove this film,
since it is no longer required. Now insert the CD in the drawer with the
labeling face up, and press it firmly down into the center of the turntable. To
remove the CD, hold it by the edges and pull upwards.

Caution
! To avoid too much pressure on the open drawer, always hold the drawer at
the front with one hand when inserting or removing a CD.

PG 740 PII Product Information Bulletin

C79000-K7076-C748-01 11
Closing the Drawer Push in the drawer until it closes completely. Do not press the eject button.

Note
The EJECT function offered by various applications for opening the
CD-ROM drawer does not work with this drive.
After the drawer has been closed, the CD is tested and the access display
light on the drive starts to flash:
– If the display flashes continually, the CD is faulty but can still be read,
– If the display flashes several times and then remains lit, the CD you have
inserted is defective and cannot be read.

CD-ROM Front

2 1 3 4
1 Access display
2 Drawer
3 Eject button
4 Emergency eject

Caution
! Risk of data loss and damage to the drive!
CD-ROM drives are sensitive to vibrations and shock. Any vibrations
occuring during operation can lead to damage to the drive or CD.
Emergency removal
By inserting a pen (or a paper clip) while the device is switched off, you can
force the drawer to open.

PG 740 PII Product Information Bulletin

12 C79000-K7076-C748-01
Installing DIMM Plug the DIMM memory cards in as follows:
cards
1. First open the unit as described in Chapter 4 of the manual PG 740 PII
Programming Device.
2. Plug the cards in vertically, making sure the cut-out on the connector end
of the DIMM card engages properly.
3. Press the card lightly and tilt it downwards until it locks into place.

Caution
! Risk of damage!
The cards must be plugged in tightly, otherwise they may be damaged.

Caution
! Risk of damage!
Note that only qualified personnel should be allowed to work on the open unit,
so the warranty on the device is not affected. Authorized Siemens maintenance
and repair centers listed at the end of this Product Information Bulletin offer you
a specialist maintenance service. Refer to Chapter 5 of the manual for further
information.

PG 740 PII Product Information Bulletin

C79000-K7076-C748-01 13
Technical Specifications
Dimensions (w x h x d) 395 x 270 x 145 mm (15.5 x 10.6 x 4.7 in.)
Weight approx. 7 kg (14.3 lbs.)
Line voltage 120 VAC (85 to 132 VAC), or 230 VAC (187 to 264 VAC)
(automatic switchover at 140 VAC)
Line voltage frequency 50 / 60 Hz (47 to 63 Hz)
Brief voltage interruption max. 20 ms at 0.85 VN
(max. 10 times per hour; min. recovery time 1 s acc. to Namur)
Max. power consumption 330 W
Standby power typically 4 W
Degree of protection IP30 (covers closed)
Safety
Requirements VDE 0805 EN 60950 and IEC 950
protection class I
Protective separation between supply and secondary circuit
Noise emission <45 dB(A) to DIN 45635
Fan with speed control
Electromagnetic compatibility (EMC)
Emitted interference
limit value class B to EN 55022 CISPR22/FCC Class A
Noise immunity on AC supply lines "2kV (to IEC 100044; burst)
"1kV (to IEC 100045; ms pulse/line to line)
"2kV (to IEC 100045; ms pulse/line to ground)
Noise immunity on signal lines "2kV (to IEC 100044; burst)
Noise immunity to discharges of static electricity "4kV, Contact discharge (to IEC 100042; ESD)
"8kV, Air discharge (to IEC 100042; ESD)
Immunity to high frequency noise 10 V at 80% amplitude modulation at 1 kHz,
10 kHz  80 MHz (to IEC 100046)
10 V/m at 80% amplitude modulation at 1 kHz,
80 kHz  1 GHz (to IEC 100043)
10 V/m pulse modulated, 50% duty cycle at 900MHz
(acc. to ENV 50 204)
Environmental conditions
Temperature tested to DIN IEC 68-2-1, DIN IEC 68-2-2
operation +5o C to +40o C
storage/transport - 20 o C to +60o C
(Max. speed of temperature change 10o C/h (18o F/h)
condensation not permitted)
Relative humidity tested to DIN IEC 68-2-3
operation 5% to 80% at 25o C (77o F) (no condensation)
storage/transport 5% to 95% at 25o C (77o F) (no condensation)
Mechanical specifications
Vibration tested to DIN IEC 68-2-6
operation 10 to 60Hz; amplitude 0.035 mm
60 to 500Hz; acceleration 4.9 m/s2
With CDROM operation, max. 1 m/s2
Shock tested to DIN IEC 68-2-27
operation half-sine: 50 m/s2, 30 ms
Mother board
Integrated processor Intel Pentium II / 266 MHz
Internal processor cache 16 Kbyte
Main memory 64 Mbyte up to a max. of 384 Mbyte SDRAM
Second level cache 512 Kbyte, on the processor card
Expansion slots 1 x shared PCI/ISA; max. 170 mm
1 x PCI, max. 170 mm
Max. permissible current consumption per ISA 5 V 1.6 A; 12 V 0.3 A; -12 V 0.05 A; -5 V 0.05 A
slot

PG 740 PII Product Information Bulletin

14 C79000-K7076-C748-01
 Drives
Floppy disk drives 3.5" (1.44 Mbyte)
Hard disk drive 3.5" / 5.2 Gbyte
CDROM drive IDE (ATA), 650 MB 20 x speed
Hard disk interface IDE, Ultra DMA
Average access time 13 ms
LC display
Type active TFT (Thin Film Transistor)
Size 270 x 202 mm, equivalent to 13.3" (w x h)
Resolution 1024 x 768 (XGA)
Colors available 218 colors available
Contrast min. 150 : 1
Brightness > 100 cd/m2
Response time 30 / 50 ms (trise / tfall)
Faulty spots permitted Bright dots: 15 max, Green Bright dots 6 max, ioin 5 max
Black dots: 15 max, Join 2 max
Graphics
Graphics Super VGA with Windows accelerator
Graphics chip C&T, 65555
Graphics memory 2 MByte ED0 DRAM
Interface to processor PCI bus 32 bit
Resolutions / frequencies / colors 640 x 480 / 75 Hz / 16.7 Mio colors
800 x 600 / 75 Hz / 65536 colors
1024 x 768 / 75 Hz / 256 colors (16.7 Mio)
1280 x 1024 / 256 colors
Keyboard
Type MF2compatible; with cursor block and numeric keypad;
removable; 101 keys
Key spacing 19.05 mm
Key stroke 3 mm
Keytops international / German
Integrated pointing device 16 mm trackball (PS/2compatible)
Interfaces
COM1 V.24 / V.28 (up to 30 m) or 20mA (TTY) (up to 1000 m) active or
passive (25way socket)
COM2 V24 (9pin connector)
LPT1 Centronics, primarily for printer (parallel) (25way socket)
VGA for external monitor (15way VGA socket)
Keyboard for keyboard with integrated trackball (6way mini DIN socket)
PS/2compatiblemouse external mouse connection
Cardbus / PC card interface interface for Cardbus / PC cards (type II; version 2.01)
(Controller from TI: PCI1131)
Submodule interface programming interface for SIMATIC S5 submodules
Memory card interface programming interface for SIMATIC memory cards
MPI, I/O interface for SIMATIC MPI or PROFIBUSDPnetworks (9way socket);
1.2 - 12 Mbps, (CP5611compatible)
LED Controls
LEDs on the device Power On (green) / Standby (red)
Hard disk access
Floppy disk access
S5 submodule/memory card active
MPI/DP token passing
LEDs on the keyboard Caps Lock
Scroll Lock
Num Lock
Audio
Audio controller CS 4238 from Crystal
Headphones and microphone connection Connection for 3.5 mm jack connector

PG 740 PII Product Information Bulletin

C79000-K7076-C748-01 15
Notes on the CE Symbol

The following applies to the SIMATIC product described in this product

information bulletin:

EMC Directive This product fulfils the requirements for the EC directive 89/336/EEC on
“electromagnetic compatibility” and the following fields of application apply
according to this CE symbol:

Field of Application Requirement For

Emitted Interference Noise Immunity
Residential, commercial,
EN 50081-1: 1992 EN 50082-1: 1992
and light industry.
Industry EN 50081-2: 1993 EN 50082-2: 1995

Low Voltage This product fulfils the requirements for the EC directive 73/23/EEC on “low
Directive voltage” and was tested to EN60950.

Declaration of The EC declarations of conformity and the documentation relating to this are
Conformity available to the authorities concerned, according to the above EC directive,
Article 10 (1), from:
Siemens AG
Bereich Automation & Drives
A&D AS E4
Ms. Zisler
Postfach 1963
D-92209 Amberg
Tel.: 09621 80 3283
Fax: 09621 80 3278

Observing the The setup guidelines and notes on safety given in the manual must be observed
Setup Guidelines on startup and during operation.

ISO 9001 The quality assurance system for the whole product process (development,
Certificate production, and marketing) fulfills the requirements of ISO 9001
(corresponds to EN29001: 1987).
This has been certified by the German society for the certification of quality
management systems (DQS).
EQ-Net certificate no.: 1323-01

Software License The PG 740 PII is shipped with the software already installed. Please observe
Agreement the relevant license agreements.

Product All the important information required to start up and install your software
Information can be found in the enclosed Product Information.

PG 740 PII Product Information Bulletin

16 C79000-K7076-C748-01
Certification for the USA and Canada

UL/CSA Important for the USA and Canada:

Certification
One of the following markings on a device is indicative of the corresponding
approval:

Unterwriters Laboratories (UL) to the UL 1950 standard.

Unterwriters Laboratories (UL) to Canadian standard C22.2 No. 950.

C

Underwriters Laboratories (UL) to Standard UL 1950, Report E11 5352

C US and Canadian Standard C22.2 No. 950.

UL Recognition Mark

Canadian Standard Association (CSA) to standard C22.2 No. 950.

Canadian Standard Association (CSA) to American standard UL 1950.

NRTL

Options

Hardware You can add to the functionality of your PG 740 PII by expanding the
Expansion configuration of the hardware to fit your individual requirements. The
following table shows the options offered by Siemens. Please contact your
Siemens sales representative for further options.

Option Order Number

Memory expansion 64 Mbyte 6ES7 791-0FR00-0XA0
Memory expansion 128 Mbyte DIMM 6ES7 791-0GS00-0XA0
MPI connecting cable for 12 Mbps 6ES7 901-4BD00-0XA0

Caution
! Risk of damage!
The electronic components of the printed-circuit boards are highly sensitive
to electrostatic discharge. When handling the boards or cards, you must
follow the guidelines for electrostatically sensitive components (ESD
guidelines at the end of the manual), otherwise the module or device may be
damaged.

PG 740 PII Product Information Bulletin

C79000-K7076-C748-01 17
SIMATIC Customer Support Hotline for the PG 740 PII

SIMATIC Customer Open round the clock, world-wide:

Support Hotline

Nuremberg
Johnson City

Singapore

Simatic Basic Hotline

Nuremberg Johnson City Singapore

SIMATIC BASIC Hotline SIMATIC BASIC Hotline SIMATIC BASIC Hotline
Local time:Mo.-Fr. 8:00 to 18:00 Local time:Mo.-Fr. 8:00 to 17:00 Local time:Mo.-Fr. 8:30 to 17:30
Phone: +49 (911) 895-7000 Phone: +1 423 461-2522 Phone: +65 740-7000
Fax: +49 (911) 895-7002 Fax: +1 423 461-2231 Fax: +65 740-7001
E-Mail: simatic.support@ E-Mail: simatic.hotline@ E-Mail: simatic@
nbgm.siemens.de sea.siemens.com singnet.com.sg
GMT: +1:00 GMT: –5:00 GMT +8:00
SIMATIC Premium Hotline
(Calls charged, only with
SIMATIC Card)
Time: Mo.-Fr. 0:00 to 24:00
Phone: +49 (911) 895-7777
Fax: +49 (911) 895-7001
GMT +01:00

SIMATIC Customer The SIMATIC Customer Support team offers you substantial additional
Support Online information about SIMATIC products via its online services:
Services General current information can be obtained from:
– the Internet under http://www.ad.siemens.de/simatic
– the Fax-Polling number 08765-93 02 77 95 00
Current product information leaflets and downloads which you may find
useful are available:
– on the Internet under
http://www.ad.siemens.de/support/html_00/
– via the Bulletin Board System (BBS) in Nuremberg (SIMATIC
Customer Support Mailbox) under the number +49 (911) 895-7100.
To access the mailbox, use a modem with up to V.34 (28.8 Kbps) with
parameters set as follows: 8, N, 1, ANSI; or dial in via ISDN (x.75, 64
Kbps).

PG 740 PII Product Information Bulletin

18 C79000-K7076-C748-01
Regional Repair Centers
SIMATIC Hotline
If problems occur, the SIMATIC Hotline should be able to help.
Siemens AG
AUT 1 CS
Gleiwitzerstr. 555
D-90475 Nürnberg-Moorenbrunn
Telefon: (49)911-895-7000
Fax: (49)911-895-7001
(49)911-895-7002
Region PG Repair Center Phone
Augsburg ATD TD ABG 6 (0821) 3252 599
Berlin ATD TD BLN 5 (030) 386 34926
Bielefeld ATD TD (0521) 291 323
Bremen ANL TD 47 (0421) 364 2996
Chemnitz A&D B 14 (0371) 475 3860
Erlangen ATD TD 3 LSE-ITC (09131) 7 32714
Erlangen ATD TD 3 LSE-RC (09131) 7 31048
Essen ATD TDE (0201) 816 1580
Frankfurt ANL TD 84 (069) 797 7358
Fürth A&D SE B 9.1 (0911) 750 2741
Hamburg ANL TD FSZ (040) 2889 4230
Hanover ANL TD HVR 1 (0511) 877 2241
Karlsruhe A&D AS EWK PLZ 52 (0721) 595 4183
Kassel ATD TD (0561) 7886 434
Cologne ATD TD SSH 5 (0221) 576 6516
Langen ATD TD E (069) 797 5608
Leipzig ATD TD 31 (0341) 210 2049
Mannheim ATD TD 9 (0621) 456 1328
Munich ATD TD MCH 53 (089) 9221 6213
Nuremberg ATD TD S 1 (0911) 654 6117
Saarbrücken ATD TD 3 (0681) 386 2598
Stuttgart ATD TD SDW 5 (0711) 137 6228
Weilimdorf

PG 740 PII Product Information Bulletin

C79000-K7076-C748-01 19
 Country PG Repair Center Phone
Argentina WA. SERVICE 0054 1 738 7333
Australia Technical Service 0061 3 9420 72 74
Austria SERVICE SHOP 0043 1 1707 23729
Belgium ES 1-4-5/AQ (15/+0) 0032 2 536 2905
Brazil STI A 43 E 0055 11 7947 1999
China AUT 1 Customer Support 0086 10 643 61888 3371
Denmark GR.319-ET 0045 7640 5151
England Control Systems (Repair 0044 161 446 5760
Centre)
Finland TTR 3/Automaatiohuolto +358051 3835
France M.et S/SER 0033 1 4922 3160
India AUT 1 Quality Control 0091 253 381462
Italy SERVICE T 47 A 0039 2 6676 3490
Mexico EA-ST Servicios Tecnicos 0052 5 328 2078
Netherlands FS-REP B 3.0.24 0031 70 333 3858
Poland Bioro Automatyki 0048 22 670 91 66
Portugal DE/AT 00351 1 7573234
Singapore ATD Technical Service 0065 740 7150
South Africa FSPC 0027 11 407 4838
Spain ST4/EIA 0034 1 754 5406
Sweden TT-Service 0046 8 728 14 62
Switzerland TDS 2 0041 1 749 1304
USA REPAIR CENTER 001 423 461 2497
In countries not listed above, please contact your local service representative.
He will arrange for your repairs to be carried out.

PG 740 PII Product Information Bulletin

20 C79000-K7076-C748-01