Elop Ii V5.1: Upgrade Supplementary Sheet For Installing
Elop Ii V5.1: Upgrade Supplementary Sheet For Installing
Elop Ii V5.1: Upgrade Supplementary Sheet For Installing
1
Upgrade
Supplementary Sheet for Installing
All HIMA products mentioned in this manual are protected by the HIMA trade-mark. Unless noted
otherwise, this also applies to other manufacturers and their respective products referred to herein.
All of the instructions and technical specifications in this manual have been written with great care and
effective quality assurance measures have been implemented to ensure their validity. For questions,
please contact HIMA directly. HIMA appreciates any suggestion on which information should be
included in the manual.
Equipment subject to change without notice. HIMA also reserves the right to modify the written
material without prior notice.
For further information, refer to the HIMA-DVD and our website http://www.hima.de and
http://www.hima.com.
Contact
HIMA Address
HIMA Paul Hildebrandt GmbH
P.O. Box 1261
68777 Brühl, Germany
Tel: +49 6202 709-0
Fax: +49 6202 709-107
E-mail: info@hima.com
1 License information
License package ELOP II upgrade to version 5.1
Hardlock serial number xxxx
Hardlock OEM User No xxxx
Activation signature xxxx
2 System requirements
Minimum system requirements:
Intel® Pentium® III 500 MHz
256 MB of available RAM
500 MB of available hard disk space
Resolution 1024*768 (16-bit)
Ethernet and/or serial interface
Microsoft® Windows® XP Professional (32-bit) Service Pack 2 or higher with Microsoft ® .NET Framework
2.0 Service Pack ≥1 and Language Pack DE,
Microsoft® Windows® 7 Professional/Ultimate (32-bit),
Microsoft® Windows® 7 Professional/Ultimate (64-bit) – XP-Mode (tested with Ultimate)
ELOP II V5.1 is applicable for all releases of the operating system BS41q/51q V7.0-8. HIMA recommends to use the
current H41q/H51q operating system.
4 Installation
ELOP II V5.1 uses a hardlock as licensing method. Install the hardlock drive and ELOP II on the PC. Follow the set-up
instructions.
1. Windows administrator rights on the PC are required to install the hardlock driver.
3. Install the hardlock drive and connect the hardlock to the PC.
The hardlock is recognized automatically. The LED on the USB hardlock is lit.
3. The installation language (e.g., German) is used as default language for ELOP II V5.1. Upon completion of the
installation process, however, it is possible to change the language, e.g., to English (use Administration located
in the Control Center).
4. The hardlock delivered with ELOP II V5.1 was already activated for the corresponding version. If a hardlock for
a previous licence is in use, follow the instructions specified in Chapter 5 to activate it.
Step 1: Start after the installation of ELOP II V5.1. If the version has not been activated yet, an error message appears.
Click OK. The Activate Feature dialog box for entering the activation signature is displayed.
Step 2: In the Activate Feature dialog box, enter the activation signature.
The hardlock has been enabled successfully. This hardlock can now be used to start ELOP II V5.1. Repeat the
previous steps for each hardlock for which ELOP II V5.1 should be activated.
Step 4: If the activation was not successful, the following error message appears:
Potential causes:
Incorrect entries.
Case sensitivity was ignored.
O used instead of 0 (zero), or vice versa.
Blanks at the end of the signature.
The entry has less than 15 characters.
Click OK to confirm the error message and enter a new activation signature.
If a new error message appears after properly entering the signature, the activation signature used is invalid or
does not comply with the hardlock's serial number, see Chapter 6.
Close the Activate Feature dialog box and confirm the message.
To enter the activation signature, select Tools, Activate Feature from the ELOP II's menu bar or use the ELOP II's
command prompt, see Chapter 6.
The conversion cannot be undone. Save the project data before converting the project.
Please refer to the document (HI 800 185 E) for more information on the conversion procedure!
9 Support
If problem occur during installation or license activation, contact HIMA support. The free HIMA hotline is available from
Monday to Friday, 8.30 am – 4.00 pm (CET/CEST).
Phone ++49 6202 709-255
++49 6202 709-258
Fax: ++49 6202 709-199
E-mail: support@hima.com
+,(
+,0$3DXO+LOGHEUDQGW*PE+
UHJLVWHUHGWUDGHPDUNRI
+,0$3DXO+LOGHEUDQGW*PE+
+,0$3DXO+LOGHEUDQGW*PE+
$OEHUW%DVVHUPDQQ6WU_%UKO*HUPDQ\
3KRQH_7HOHID[
LQIR#KLPDFRP_ZZZKLPDFRP