User's Guide: D-Link Antenna Kits
User's Guide: D-Link Antenna Kits
User's Guide: D-Link Antenna Kits
/antenna
System Requirements
Installation
Step 1
loosen the screw from the surge protector.
Ground
Step 3
find a conductive material nearby the antenna installation sites, connect another end of the wire
into position, there are several options:
(1) Use a long screw to stick into the ground tightly, connect another wire onto.
(2) fix or solder another end of wire onto a steel material/ bar under steel construction,
such as wall for buildings, railings or other conductive materials which set up from
the ground.
Remark:
(1) for the ground screw you use, we suggest the longer (deeper into ground) the better performance it has.
(2) please use a copper wire with diameter at least from 2.0mm, the thicker the diameter, the higher
voltage it can sustain.
System Requirements
ANT24-Series ANT24-0700 Install Guide
Regulations
D-Link WLAN Antenna-Kit
Extended range differentiation for FCC/CE regulated regions
CE ETSI EN 300 328 regulated European Union (EU) regions
Based on ETSI EN 300 328, the system device and its antenna Emitted Isotropic Radiated Power
(EIRP) are limited to operate within a 20dBm gain. The range extension provided by the antenna
kit should comply with the restrictions set by the EU.
Outdoor Installations
To fully benefit from D-Link’s extensive range of quality outdoor antennas, please note that they
should be installed by a professional and must comply with the Europe Union CE wireless radio
frequency output power. Cable length will affect the antenna gain dramatically.
EIRP limitaton:
2.4GHz~2.5GHz 5.15GHz~5.35GHz 5.47~5.725 5.75GHz~5.875GHz
point to multi-point
20dBm ave.
ETSI 23dBm 30dBm X
23dBm peak.
point to point
Cable Loss
Cable loss (dB) Cable loss(dB)
Model Cable Type Length Interface
@ 2.4GHz @5GHz
ANT24-CB03N LMR400 3m N plug to N jack 1 1.75
Note:
1. The loss value includes two connectors ( around 0.3~0.4dB @ 2.4GHz, 0.39~0.52dB@5GHz).
2. The longer cable you use, the more attenuation it causes, therefore, the extended range might be
shorten then a normal link with default cables.
3. To comply with EU regulation, please use longer cables which can cause enough attenuation value.
4. For more detail of connectors type, please refer to the appendix page.(P.30)
System Requirements
ANT24-Series
System Requirements
ANT24-Series ANT24-0700 Install Guide
D-Link ANT24-0401
Ceiling Mount Antenna
Electrical specification
58°~75°
System Requirements
ANT24-Series
SAA04-050170
Electrical Specification
Frequency range
Ø19×330mm 2400 MHz - 2500 MHz
Humidity 100% @ 25 C o
HPBW / vertical 32
Lightning protection DC ground
o
Radome color Downtilt
Gray-white 0
Radome material Fiberglass
Power handling 20 W (cw)
32
Radiator material Micro striple line
Impedance 50 Ohms
Weight 0.8kgw
Connector SMA Plug
Dimensions 330 x 19 mm
Cable ULA 168, 100cm
Weight 0.8kg
o o
150 30
o o
-150 -30
o
-120
o
-60
o
-90
http:// www.smartant.com TEL: +886 (0)3 578-3188 FAX: +886 (0)3 578-3189 E-mail: service@smartant.com
EMW2403005AMLM01
All right reserved by SmartAnt Telecom Co., Ltd.
P1
System Requirements
ANT24-Series ANT24-0700 Install Guide
D-Link ANT24-0501
Indoor Omni-Directional Antenna
Electrical specification
Frequency Range 2400~2500MHz
Impedance 50Ω Normal ANT24-0700 / ANT24-0700C
VSWR 1.92 Max
Return Loss -10 dB Maximum
Far-field amplitude of D-link-7dBi-H1-1020.nsi Far-field amplitude of D-link-7dB
Antenna Structure Helis antenna
0 0
345 15 345 15
Cable color
ANT24-0700 / ANT24-0700C
Gray 210 150 210
330 30 330 30
ANT24-0501C/ ANT24-0501
270 90 270 90
-20 -10 0 dB 0 -20 -10 0 dB 0
270
345 15 345 15
255
285
300
315
225
240 120 240 120
300 60 300
330
210
210
225 135 225 135
285 75 285
195
345
195
210 150 210 150
180
-20 -10 0 dB -20
0
15
30
150
ANT24-0501C/ ANT24-0501
135
45
135
0
60
dB
75
90
285
0 0
345 15 345 15
Far-field amplitude of D-link-5dBi-v-1020.nsi
240
300
330 30 330 30
225
315
225
210
345
195
285 75 285 75
180
0
270 90 270 90
15
165
30
150
-Two Crews
135
45
135
0
60
dB
75
-One sticker
90
System Requirements
ANT24-Series
D-Link ANT24-0501C
Indoor Omni-Directional Antenna
Electrical specification
Frequency Range 2400~2500MHz
Impedance 50Ω Normal
VSWR 1.92 Max
Peak Gain 5dBi
Admitted Power 1W
E-Plane 36 deg.
H-Plane 360 deg.
Physical Properties
Connector Reverse SMA plug
Antenna Material ABS, ABS+PC
Operating Temp -20°C ~ +65°C
Storage Temp -30°C ~ +75°C
Color Antenna: Metallic gray and silver
36°
Attach to AP/Router
Package Contents
-One ANT24-0501C 2.4GHz 5dBi indoor
omni-directional antenna with a RP-SMA
plug connector
-One RP SMA/ RP TNC adapter
-One registration card and company contact
guide
System Requirements
ANT24-Series ANT24-0700 Install Guide
ANT24-Series
D-Link ANT24-0502
D-Link ANT24-0502
Indoor Omni-Directional
Indoor Omni Directional AntennaAntenna
Electrical Specification
Frequency range 2400 MHz - 2500 MHz
Gain 5.0dBi
HPBW/horizontal 360°
HPBW/vertical 40°
Downtilt 0°
Impedance 50 Ohms
-18
Dimensions ӽ13.5 x 177 mm -15
-12
-9
240 120
-6
-3
0
3
210 150
6
180
10
System Requirements
ANT24-Series
D-Link DWL-50AT
Indoor Omni-Directional Antenna
Electrical specification
5.0dBi Typical
2.0:1 Max.
360°
30 degree
nominal
197 mm(length)
29.5gw
30°
Far-field
Far-field amplitude
amplitude of
of C147-510017-A-V.nsi
C147-510017-A-V.nsi
2.4GHz 2.45GHz 2.5GHz
2.4GHz 2.45GHz 2.5GHz
0
345 0 15
345 15
330 30
330 30
315 45
315 45
300 60
300 60
285 75
285 75
270 90
270 -20 -10 0 dB 90
-20 -10 0 dB
255 105
255 105
240 120
240 120
225 135
225 135
210 150
210 150
195 165
195 180 165
180
Far-field
Far-field amplitude
amplitude of
of C147-510017-A-H.nsi
C147-510017-A-H.nsi
2.4GHz 2.45GHz 2.5GHz
2.4GHz 2.45GHz 2.5GHz
0
345 0 15
345 15
330 30
330 30
315 45
315 45
300 60
300 60
285 75
285 75
270 90
270 -20 -10 0 dB 90
-20 -10 0 dB
255 105
255 105
240 120
240 120
225 135
225 135
210 150
210 150
195 165
195 180 165
180
11
System Requirements
ANT24-Series ANT24-0700 Install Guide
D-Link ANT24-0600
Indoor Directional Antenna
Electrical specification
Frequency Range 2400~2500MHz
Impedance 50Ω Normal
VSWR 1.92 Max
Return Loss -10 dB Maximum
Antenna Structure Pateh antenna
Peak Gain ( w/o cable loss) 6.0 dBi @ 2.45GHz ( typical)
Admitted Power 1W
Cable loss( 1.5m) 2.1dB@2.45GHz
E-Plane 68°
H-Plane 80°
Physical Properties
Cable Filotex 50Ω
Antenna Cover ABS
Antenna Base PC
Operating Temp -20°C ~ +65°C
Storage Temp -30°C ~ +75°C
Color White
Package Contents
-One ANT24-0600 2.4GHz indoor 6dBi directional
Antenna with 1.5 Filotex cable and RP-SMA Jack
connector
-One RP-SMA/ RP-TNC adaptor
-One User’s QIG
-Two Crews
-Two plastic fixings
-One sticker
12
System Requirements
ANT24-Series
D-Link ANT24-0700
Indoor Omni-Directional Antenna
Electrical specification
Frequency Range 2400~2500MHz
Impedance 50Ω Normal
VSWR 1.92 Max
Return Loss -10 dB Maximum
Antenna Structure Helis antenna
Peak Gain ( w/o cable loss) 7dBi
Admitted Power 1W
Cable loss( 1.5m) 2.1dB@2.45GHz
E-Plane 24 deg.
H-Plane 360 deg.
Physical Properties
Cable RG-178 50Ω
Cable length 1.5 M
Cable color Gray
Connector Reverse SMA plug
Antenna Material ABS, ABS+PC
Operating Temp -20°C ~ +65°C
Storage Temp -30°C ~ +75°C
Color Antenna: Metallic gray and silver
Base: Metallic gray
Package Contents
-D-Link ANT24-0700 2.4GHz Omni-Directional Indoor
Antenna
-SMA to TNC Adapter
-Magnetic Base with 1.5m Extension Cable
-Mounting Kit
-Installation Guide
13
System Requirements
ANT24-Series ANT24-0700 Install Guide
D-Link ANT24-0700C
Indoor Omni-Directional Antenna
Electrical specification
Frequency Range 2400~2500MHz
Impedance 50Ω Normal
VSWR 1.92 Max
Return Loss 10 dB Maximum
Antenna Structure Helis antenna
Peak Gain ( w/o cable loss) 7dBi
Admitted Power 1W
Cable loss( 1.5m) 2.1dB@2.45GHz
E-Plane 24 deg.
H-Plane 360 deg.
Physical Properties
Cable RG-178 50Ω
Cable length 1.5 M
Cable color Gray
Connector Reverse SMA plug
Antenna Material ABS, ABS+PC
Operating Temp -20°C ~ +65°C
Storage Temp -30°C ~ +75°C
Color Antenna: Metallic gray and silver
Base: Metallic gray
Attach to AP/Router
Package Contents
-One ANT24-0700C 2.4GHz 7dBi indoor omni-
directional antenna with a RP-SMA plug connector
-One RP SMA/ RP TNC adapter
-One registration card and company contact guide
14
Omni-Directional Antenna for 2.4 ANT24-Series
GHz
System Requirements
Connector N female
1
2
3
2
1.Antenna body
3
2.M5-0.8
Environmental & Mechanical nut
Characteristics
4
Picture (1)
3.M5 Washer
4
Picture (1)
Survival wind speed 216 km/hr
4.M5 U-Type Screw
o
90
o
o 60
120
5.Screw
o
When you install the antenna,
please tryoto find an open space like
TemperaturePole(max φ=50mm) - 6.Anchor
40 C to the+80
When picture C
you install the antenna,
(1) , avoid to install like
150
o
30
o
please try to(2)
the picture find an open
cause space like
the omni-directional
the picture (1) ,be
avoid to install like
Pole(max φ=50mm) signals
o might blocked and performance
Humidity 1 Antenna body 95% @ the
25 C
picture (2) cause the omni-directional
be affected.
signals might be blocked and performance
2 M5-0.8 nut
be affected.
13 Antenna body
M5 Washer o -30 -20 -10 -3
o
180 0
Lightning protection
24 M5-0.8 nut Screw
M5 U-Type
35 M5 Washer
Screw
DC ground
46 M5 U-Type Screw
Anchor
5 Screw
Radome color 6 Anchor Gray-white -150
o -30
o
Picture (2) o
-90
1
Weight 337 gw Picture (2) Vertical
Dimensions 520 x 19 mm
5
o
5 6 90
o o
120 60
6
o o
150 30
Picture (3) o
o -30 -20 -10 -3 0
180
Picture (3)
(50cm) Horizontal
15
System Requirements
ANT24-Series ANT24-0700 Install Guide
65°
Housing material AL6063
Weight 0.3 kgw
Dimensions 120 x 120 x 43 mm
16
System Requirements
ANT24-Series
D-Link ANT24-1200
Indoor Directional Panel Antenna
Electrical specification
Frequency range 2400 MHz - 2500 MHz
Gain 12 dBi
VSWR 1.5 : 1 Max
Polarization Linear, vertical
HPBW / horizontal 80
HPBW / vertical 23
Front to back ratio 15 dB
Downtilt 0
Power handling 20 W(cm)
Impedance 50 Ohms
Connector SMA female
17
System Requirements
ANT24-Series ANT24-0700 Install Guide
D-Link ANT24-1201
Outdoor Directional Yagi Antenna
Electrical specification
Frequency range 2400 MHz - 2500 MHz
Gain 12 dBi
VSWR 1.5 : 1 Max
Polarization Linear, vertical
50
HPBW / horizontal 50
HPBW / vertical 50
Front to back ratio 15 dB
Downtilt 0
Power handling 10 W (cm)
Impedance 50 Ohms
Connector N female
Cable UL 198; 32cm
18
System Requirements
ANT24-Series
19
System Requirements
ANT24-Series ANT24-0700 Install Guide
D-Link ANT24-1400
Outdoor Directional Panel Antenna
Electrical specification
Frequency range 2400 MHz - 2500 MHz
Gain 14 dBi
VSWR 1.5 : 1 Max
Polarization Linear, vertical
HPBW / horizontal 30
HPBW / vertical 30
Front to back ratio 15 dB
Downtilt 0
Power handling 10 W (cm)
Impedance 50 Ohms
Connector N female
Cable ULA198
Pole mounting
method 2.
Pole mounting
method 1.
20
System Requirements
ANT24-Series
D-Link ANT24-1800
Outdoor Directional Panel Antenna
Electrical specification
Frequency range 2400 MHz - 2500 MHz
Gain 18 dBi
VSWR 1.5 : 1 Max
Polarization Linear, vertical
HPBW / horizontal 15
HPBW / vertical 15
Front to back ratio 26 dB
Downtilt 0
Power handling 50 W (cm)
Impedance 50 Ohms
Connector N female
21
System Requirements
ANT24-Series ANT24-0700 Install Guide
D-Link ANT24-2100
Outdoor Directional Antenna
22
System Requirements
ANT70-Series
D-Link ANT70-0800
Dual-Band
Dual-Band Omni-Directional
Omni-Directional Antenna Antenna
Electrical specification
forFrequency
2.4 /Range
5.2 / 5.4 GHz
2400 MHz - 2500 MHz 4900 MHz - 5470
MHz
Gain 8 dBi 8 dBi
ANT70-0800
VSWR 2.0 : 1 Max.
HPBW / horizontal 360°
Electrical Specification
HPBW / vertical 15°
Polarization Linear, vertical
Frequency range 24005 W
Power handling MHz
(cw) - 2500 MHz 4900 MHz - 5470 MHz
Weight
Omni-Directional Antenna350
forg 802.11b/g
Connector
Dimensions N Jack When you install the antenna,
Mounting Configurations for80x78x870
pole/ wallmm please try to find an open space like
the picture (1) , avoid to install like
Pole(max φ=50mm) the picture (2) cause the omni-directional
signals might be blocked and performance
be affected.
1 Antenna body
2 M5-0.8 nut
3 M5 Washer
1 4 M5 U-Type Screw
5 Screw
Weight
3.M5 WasherAnchor
6 348 g
4.M5 U-Type Screw Picture (3)
Dimensions
5.Screw
ø22 x 90 mm
Wall Please always install the antenna
6.Anchor
1 Picture (2)
vertically to the horizontal surface, not
recommended to mount it perpendicular
to the wall.
-Water-proof tape
Wall
-Quick Installation Guide Please always install the antenna
vertically to the horizontal surface, not
recommended to mount it perpendicular
to the wall.
23
System Requirements
ANT70-Series ANT24-0700 Install Guide
D-Link ANT70-0801
Dual-Band Omni-Directional Antenna
Dual-Band Omni-Directional Antenna
ANT70-0801
Gain 8 dBi
MHz
8 dBi
VSWR 2.0 : 1 Max.
Electrical Specification
HPBW / horizontal 360°
HPBW / vertical 15°
Frequency range 2400 MHz - 2500 MHz 5400 MHz - 5875 MHz
Polarization Linear, vertical
Gain
Power handling
8 5dBi
W (cw)
8 dBi
VSWR
Impedance 2.0 : 1 Max.
50 Ohms
Connector Omni-Directional Antenna for 802.11b/g
N Jack
HPBW / horizontal 360°
Mounting Configurations for pole/ wall
HPBW / vertical
Environmental 15°
& Mechanical Characteristics
Polarization
Survival wind speed Linear,
216 km/hrvertical
Temperature - 40°C to +70°C 1
Power handling 5 W (cw)
Humidity 95% @ 55°C
Impedance
Radome color 50Gray
Ohms 2
3
Connector N ABS,
Jack
4
Radome material UV resistant
Picture (1)
Weight 350 g
Omni-Directional Antenna for 802.11b/g
Dimensions 80x78x870 mm When you install the antenna,
Mounting Configurations for pole/ wall please try to find an open space like
the picture (1) , avoid to install like
Pole(max φ=50mm) the picture (2) cause the omni-directional
signals might be blocked and performance
be affected.
Environmental & Mechanical Characteristics 1
2
3
Antenna body
M5-0.8 nut
M5 Washer
1
Temperature 2
3 - 40°C to +70°C 2.4 GHz: 5 GHz:
4
3 M5 Washer
Dimensions
2.M5-0.8 nut 4
5
M5 U-Type Screw
Screw ø22 x 90 mm
3.M5 Washer 6 Anchor
Package Contents
-D-Link ANT70-0801
5
6
Antenna
-Extension Cable(50cm)
-Surge Protector
-Mounting Kit
-Water-proof tape
Picture (3)
24
System Requirements
ANT70-Series
D-Link ANT70-1000
Dual-Band Directional Panel Antenna
Electrical specification
Frequency Range 2400 MHz - 2500 MHz 4900 MHz - 5875
MHz
Gain 8.5 dBi 10.5 dBi
VSWR 2.0 : 1 Max. 2.0 : 1 Max.
HPBW / horizontal 58° 45°
HPBW / vertical 55° 45°
Polarization Linear, vertical
Power handling 5 W (cw)
Front to back ratio 15dB
Downtilt 0°
Impedance 50 Ohms
Connector N Jack 2.4 GHz:
55
Assembly Drawing
Humidity 95% @ 55°C
Radome color Gray
Radome material ABS, UV resistant
Weight 150 g
5 GHz:
Dimensions 114 x124 x 40 mm
45
45
25
System Requirements
ANT70-Series ANT24-0700 Install Guide
D-Link ANT70-1800
Dual-Band Directional Panel Antenna
Electrical specification
Frequency Range 2400 MHz - 2500 MHz 4900 MHz - 5875
MHz
Gain 14 dBi 18 dBi
VSWR 2.0 : 1 Max. 2.0 : 1 Max.
HPBW / horizontal 30° 15°
HPBW / vertical 30° 15°
Polarization Linear, vertical
Power handling 10 W (cw)
Front to back ratio 15dB
2.4 GHz:
Downtilt 0°
Impedance 50 Ohms
Connector N Jack 30
30
Survival wind speed 216 km/hr
Temperature - 40°C to +80°C
Humidity 95% @ 55°C
Radome color Light Gray 5 GHz:
Radome material ABS, UV resistant
Weight 400 g 15
15
Package Contents
-D-Link ANT70-1800 Antenna
-Extension Cable(50cm)
-Surge Protector
-Mounting Kit
-Water-proof tape
-Quick Installation Guide
26
System Requirements
Fresnel Zone
Line-of-Sight (LOS)
Visual LOS is the ability to see from one site to the other. It requires only a
straight liner path between two points.
RF LOS requires not only visual LOS, but also a football-shaped path free of
obstacles for data to optimally travel from one point to another.
Fresnel Zone:
In order to achieve the greatest range, the football-shaped path in which radio
waves travel must be free of obstructions. Buildings, trees or any other
obstacles in the path will decrease the communication range. If the antennas
are mounted just barely off the ground, over half of the Fresnel zone ends up
being obstructed by the earth resulting in significant reduction in range. To
avoid this problem, the antenna should be mounted high enough off of the
ground so that the earth does not interfere with the central radius of the
Fresnel zone.
27
System Requirements
Fresnel Zone ANT24-0700 Install Guide
How far above the ground and other obstacles the antennas need to be is
determined by the radius of the Fresnel zone. The radius of the Fresnal Zone
depends upon the frequency and distance between the two radios. The
following table provides approximate Fresnel zone radius:
In order to have LOS clearance, the combined antenna height should be equal
to or at least 70% of the radius of the Fresnel zone.
Required Fresnel
Zone radius
28
Model Name ANT24-0230 ANT24-0401 ANT24-0500 ANT24-0501 ANT24-0501C ANT24-0502 ANT24-0600
Signal directivity Omni-directional Omni-directional Omni-directional Omni-directional Omni-directional Omni-directional Directional Antenna
Application range Indoor Indoor ceiling only Indoor/ Outdoor Indoor only Indoor only Indoor Indoor only
Gain (Without cable loss) 1.8dBi 3.5dBi 5dBi 5dBi 5dBi 5dBi 6dBi
Approximate Range at 1 / 11/ 54Mbps 500m /400m /200m 250m/100m / 40 m 500m/ 250m/ 60m 500m/ 200m/ 50m 550m/ 250m/ 60m 500m/ 200m /60m 600m/ 350m /80m
( Works with Indoor AP ) /100m /5m**
Approximate Range at 1/ 11 /54Mbps --- --- 1.5Km/ 1.3Km/ 200m --- --- --- ---
(Works with Outdoor AP)
Half Power Beam width H360 V70 H360 V120 H360 V32 H360 V36 H360 V36 H360 V40 H68 V80
Pigtail cable length 1.2 m --- 30cm 150cm --- --- 150cm
Antenna fixed connector PR-SMA plug SMA jack N-jack RP-SMA plug RP-SMA plug RP-SMA plug RP-SMA plug
Surge protector for outdoors --- --- Optional --- --- --- ---
Default mounting configuration Desktop Ceiling Pole Wall / desktop/magnetic Attach to AP/Router Attach to AP/Router Wall/ desktop/magnetic
Optional antenna cable kits --- --- ANT24-CB series --- --- --- ---
29
ANT24-Series
System Requirements
30
Model Name ANT24-0700 ANT24-0700C ANT24-0800 ANT24-0801 ANT24-1200 ANT24-1201
Application range Indoor only Indoor only Indoor/ Outdoor Indoor/ Outdoor Indoor only Outdoor
Gain (Without cable loss) 7dBi 7dBi 8dBi 8.5dBi 12dBi 12dBi
Approximate Range at 1 / 11/ 54Mbps 550m/ 250m/60m 600m/ 300m/ 70m 700m/ 350m/ 100m 800m/ 500m/ 150m 1.5Km / 1.2Km/ 500m ---
( Works with Indoor AP )
Approximate Range at 1/ 11 /54Mbps --- --- 2Km / 1Km/ 400m 2.5Km / 1.5Km/ 600m --- 3Km / 2.5Km/ 1Km
(Works with Outdoor AP)
Half Power Beam width H360 V24 H360 V24 H360 V15 H70 V65 H80 V23 H50 V50
Antenna fixed connector RP-SMA plug RP-SMA plug N-jack N-jack SMA jack N-jack
Surge protector for outdoors --- --- Included Included --- Included
Default mounting configuration Wall/ desktop/magnetic Attach to AP/Router Pole Wall/ pole Window/ wall Wall/ pole
Optional antenna cable kits --- --- ANT24-CB series ANT24-CB series --- ANT24-CB series
ANT24-0700 Install Guide
Model Name ANT24-1202 ANT24-1400 ANT24-1800 ANT24-2100
Approximate Range at 1/ 11 /54Mbps 3Km / 1.8Km/ 450m 6Km / 4.5Km/ 1Km 8Km / 6Km/ 1.5Km 8Km / 6Km/ 1.5Km
(Works with Outdoor AP)
Half Power Beam width H360 V6 H30 V30 H15 V15 H10 V12
Default mounting configuration Wall/ pole Wall/ pole Wall/ pole Pole
Optional antenna cable kits ANT24-CB series ANT24-CB series ANT24-CB series ANT24-CB series
31
System Requirements
32
Model Name ANT70-0800 ANT70-0801 ANT70-1000 ANT70-1800
Approximate Range at 1 / 11/ 54Mbps 2.4GHz: 700m/ 350m/ 100m 2.4GHz: 700m/ 350m/ 100m 2.4GHz: 800m/ 400m/ 150m
( Works with Indoor AP ) ---
5GHZ: 1K/ 500m/ 200m 5GHZ: 1K/ 500m/ 200m 5GHZ: 1.2K/ 600m/ 250m
Approximate Range at 1/ 11 /54Mbps 2.4GHz: 800m/ 450m/ 150m 2.4GHz: 800m/ 450m/ 150m 2.4GHz: 1K/ 500m/ 200m 2.4GHz: 6K/ 4.5m/ 1Km
(Works with Outdoor AP) 5GHZ: 1K/ 500m/ 200m 5GHZ: 1K/ 500m/ 200m 5GHZ: 1.5K/ 700m/ 300m 5GHZ: 8Km/ 5Km/ 1.5Km
2.4GHz: H360 V15 2.4GHz: H360 V15 2.4GHz: H58 V55 2.4GHz: H30 V30
Half Power Beam width 5GHz: H360 V15 5GHz: H360 V15 5GHz: H45 V45 5GHz: H15 V15
Optional antenna cable kits ANT24-CB series ANT24-CB series ANT24-CB series ANT24-CB series
NOTE:
*1.Extended range reference based on RF-Output Power 16dbm( Indoor AP), 23 ( outdoor AP) with default cable loss,
*2.The transmission distance range might depend on the two same spec antennas with default cable loss under free line-of –sight environment.
*3. Effective range based on EIRP( Effected Isotropic Radiation Power. = device output power + antenna gain – cable lost )
**BW: Beam Width. H : horizontal plane pattern, V : vertical plane pattern
ANT24-0700 Install Guide
The actual range will be effected by users’ physical environment. The above figures are reference.
(Appendix)
CONNECTORS OUTLOOK
33
System Requirements
Ver. 3.00
DFWWANT00C0030