Conbextra EBG (M) : Epoxy Resin Bearing Grout
Conbextra EBG (M) : Epoxy Resin Bearing Grout
Conbextra EBG (M) : Epoxy Resin Bearing Grout
Uses Properties
An epoxy grout for use in situations where heavy dynamic or Mixed density : 1.72 g/cc
cyclic loads are encountered. The gap between a base plate
The following results are typical for the hardened grout at 300C
and substrate will need to be filled in situations such as recipro-
cating machinery, testing equipment, crane rail and transporter Colour of the mixed material Grey
rails, high speed turbines, bridge bearings, centrifuges and
Compressive strength (N/mm2)
drop forges.
ASTM D 695 at 1 day 40
Conbextra EBG(M) is suitable for a wide gap range from 3mm
7 days 60
to 50mm.
Tensile strength (N/mm2)
Also for use in conditions where chemical spillage may be
ASTM D 638 at 7 days 35
encountered. Typical situations could be met in steel works,
refineries, electroplating works and chemical plants. Chemical resistance
page 1 of 3
Conbextra EBG(M)
Formwork
Shelf life
The formwork should be constructed to be leakproof. Loss of
Conbextra EBG(M) has a shelf life of 12 months in unopened
grout material placed, but not hardened, will result in incomplete
container under normal warehouse condition.
filling of the gap.
Precautions
Mixing
Health and Safety
Pour all the contents of the base and hardener packs into a
suitable container. Mix using a slow speed power mixer until Conbextra EBG(M) contains resins which may cause sensiti-
homogenous. sation by skin contact. Avoid contact with skin and eyes and
inhalation of vapour. Wear suitable protective clothing, gloves
Placing
and eye/face protection. Barrier creams provide additional
The mixed grout should be poured or pumped under pressure skin protection. Should accidental skin contact occur, remove
steadily from one side only to eliminate the entrapment of air. immediately with a resin removing cream, followed by soap
and water. Do not use solvent. Incase of contact with eyes,
Continuous grout flow is essential. Sufficient grout must be rinse immediately with plenty of clean water and seek medical
available prior to starting grouting operation. Time gap between attention immediately - do not induce vomiting.
the successive stages of grouting should be monitored to avoid
joints. Fire
Flow characteristics Nitoflor Sol is flammable. In the event of fire extinguish with
Carbon dioxide or foam.
The maximum distance of flow is governed by the gap thick-
ness, the gravity head /pressure and ambient temperature. Nitoflor Sol : Flammable liquid
Conbextra EBG(M) is a thixotropic grout and requires to be Flash Point : 330C
pumped/poured under gravity, for filling the gaps.
Keep away from sources of ignition - no smoking. Wear suit-
Cleaning able protective clothing, gloves and eye/face protection. Use
All tools and equipment should be cleaned immediately after only in well ventilated area.
use with Nitoflor Sol. Spillages should be absorbed with sand Additional information
or sawdust and disposed in accordance with local regulations.
The Fosroc range of associated products include high strength
Limitations cementitious, epoxy grout, polyester resin based mortar for
Temperature rapid presetting of steel shims to level or for direct bedding
of small base plates; Resin Anchoring systems for same day
During application anchoring of bolts in drilled holes in concrete or rock. Also
For Conbextra EBG(M), at temperatures below 20 deg.C the available a range of products for use in construction; viz., ad-
cure rate may be slow, but will go to completion provided the mixtures, curing compounds, release agents, flooring systems
temperature remains above 5 C. 0 and repair mortars.
Estimating
Supply
Important note :
Fosroc products are guaranteed against defective materials and manufacture and are sold
subject to its standard terms and conditions of sale, copies of which may be obtained on
request. Whilst Fosroc endeavours to ensure that any advice, recommendation specification
or information it may give is accurate and correct, it cannot, because it has no direct or
continuous control over where or how its products are applied, accept any liability either
Fosroc Chemicals directly or indirectly arising from the use of its products whether or not in accordance with
any advice, specification, recommendation or information given by it.
(India) Pvt. Ltd.
Head Office telephone fax e-mail
Embassy Point, No. 150,
2nd Floor, Infantry Road, +91 80-42521900 +91 80-22281510 enquiryindia@fosroc.com
Bangalore 560 001,
Karnataka
Regional Offices
www.fosroc.com
page 3 of 3 INDIA/2020/0307A