ww6000 Instruction Book PDF
ww6000 Instruction Book PDF
ww6000 Instruction Book PDF
z
-I
0
1
a,
0
0
0
I
I CD
CD
Cl)
CD
0
C
C,
CD
0
DANGER
1. Always unplug before relamping. Replace bulb with same type rated 15 watts.
2. Do not reach for an appliance that has fallen into water. Unplug immediately.
3. Do not place or store appliance where it can fall or be pulled into a tub or sink.
Do not place in or drop into water or other liquid.
1. NAMES OF PARTS .
1
2-5. Threading 5
6. ROLL HEMMING 16
7, PIN TUCKING 18
8. CORDED OVERLOCK 19
11. LUBRICATION 20
13. ACCESSORIES 22
14. SPECIFICATIONS 23
1 2 3 4 5 6 7 8 9
I - —
10 11 12 13 14 15 16
I Spool pin
Presser foot lifter
Pressure regulator screw
Telescopic thread stand
Thread take up lever
fhread tension support
Thread tension dials
Front panel
Differential feed dial
0 Side cover
1 Stitch length adjuster
2 Presser foot
Bite width adjusting dial
Upper knife
Front cover
i Handwheel (Right side of machine)
—2—
Needle eye
.1
—3—
—4—
1
’ ss the thread through lower looper thread guide
as shown. (Fig. C)
rhen thread the hole of lower looper 3 using
weezzrs. Cut the thread leaving about 10 cm (4)
spare thread. (Fig. D)
Fig. C Fig. D
—5—
t
2-6. Preparation for Sewing and
Checking.
L
If the thread doesn’t wind around the stitch finger
of the needle plate, check it any threads are
threaded incorrectly.
—6—
L
—7—
ser foot.
+ Do not pull it out roughly as the needle will
bend and break.
)
3-4. Adjustment of the Presser Foot
Pressure
The presser foot pressure is pre-adjusted for
materials of medium (standard) thickness.
Adjustment is necessary only when you work on
very thin or very thick materials.
Accordingly, sew thinner materials with less pres
sure and thicker materials with more pressure.
Increase the pressure of the presser foot by
tightening the adjustment screw.
—8—
Right-hand r
--9
Right side 2
L
Q
9sen
Upper looper thread
en
Right side .•:.
t
9en
Ti
Right side
\
—10—
Refer to the below chart and test stitch performance on a scrap of material
you are going to use.
-..
,,
ratio is set N
. .
.
feed ratio adjustment
-I
Stretchable Knit
—
materials Jersey N-2
.. ..:.:...
::.:
s
..
Condensable
materials Georgette 0.7-N
.
>
—11—
1 II o
—1 2—
—13--
LOWER
LOOPER 2-4 5-8 2-4
THREAD
(_
- -
a —f
—14--
—1 5-
‘3
I 22
The fabric is rolled and overlocked with upper and
lower looper thread.
—16—
BITE WIDTH 5 - 6 mm 5 - 6 mm
DIFFERENTIAL FEED N N
RATIO
NEEDLE THREAD 1 - 4 1 - 4
—17—
(4) Place the fabric under the presser foot with the
hem edge in line with the side of the needle
plate and start to sew.
Raise up the presser lifter.
± Make chain-stitch at the end of the sewing.
—18—
—19—
11. WBRICATION
CLEANING
First disconnect machine from power supply by
removing plug from the electric outlet.
1. Open front cover and side cover. (See Page 3)
2. Using the brush provided, remove all the dust
and lint that has accumulated
STORAGE
1. When the machine is not in use, please
disconnect t from the power supply by
removing plug from the electric ontlot,
2. Using the vrnyt cover provided pk ase cover
your machine when you hnish your sewing.
3. Store away from bright and damp places,
SERVICING
Any questions regarding service and or operation
is to be addressed to tha. tore where th:I. machine
was purchased.
HAx1SP
Needle HAx1T
#11 #11 #14 #14
(705/1 30) or
(80) (80) (90) (90)
(For home-use sewing
machine)
(Three-thread overedging
stitch).
Overedging width
4.2—4.5mm 4.2—4.5mm 4.5—5mm
(Between left needle and
edge)
—21—
Screw drivers
Needles Tweezers
HAx1 SP
HAx1 T
#11.2
705/130
(80)
Spool Adapter
#14.. .3
(90)
-
Cleaning brush
Net
n Oiler
Vinyl cover
Lower knife
—22
Overedge width
Standard 4.5mm (Range 4.2 -.6mm)
Size of bight
Weight 8.1 kg
—23—