This document is an inspection sheet for Ex d/e/n installations. It lists items to check such as ensuring equipment is in the correct explosion protection zone, temperature class is appropriate, enclosures are intact, and cable seals are satisfactory. Inspections can be initial, commissioning, or periodic, and involve visual, rigid, or detailed checking to verify equipment and installations meet explosion protection requirements.
This document is an inspection sheet for Ex d/e/n installations. It lists items to check such as ensuring equipment is in the correct explosion protection zone, temperature class is appropriate, enclosures are intact, and cable seals are satisfactory. Inspections can be initial, commissioning, or periodic, and involve visual, rigid, or detailed checking to verify equipment and installations meet explosion protection requirements.
This document is an inspection sheet for Ex d/e/n installations. It lists items to check such as ensuring equipment is in the correct explosion protection zone, temperature class is appropriate, enclosures are intact, and cable seals are satisfactory. Inspections can be initial, commissioning, or periodic, and involve visual, rigid, or detailed checking to verify equipment and installations meet explosion protection requirements.
This document is an inspection sheet for Ex d/e/n installations. It lists items to check such as ensuring equipment is in the correct explosion protection zone, temperature class is appropriate, enclosures are intact, and cable seals are satisfactory. Inspections can be initial, commissioning, or periodic, and involve visual, rigid, or detailed checking to verify equipment and installations meet explosion protection requirements.
INSPECTION SHEET FOR EX d / Ex e / Ex n Installation
Type of inspection: ** ............................................................Degree of Control: *** ....
Type of equipment / plant: ............................................................................................. Place where is installed / Ex zone: .................................................................................. Date of inspection: ................................................ .. ..................................................... * Specify the type of Ex installation; ** It will be completed, as the case may be: the initial phase, on commissioning, the periodic phase of the survey; *** It will be completed as required: Detailed, Visual, Rigid CHECKING Result X/O 0 1 A. EQUIPMENT 1. The equipment meets requirements regarding the location EPL / Zone 2. The equipment group is correct 3. The temperature class of the equipment is correct 4. The identification of the circuitry of the equipment is correct 5. Circuit identification is available 6. Capsulation, glass parts and glass-gas seals on metal and / or components are appropriate 7. There are no unauthorized changes 8. There are no visible unauthorized changes 9. The screws, cable entries (direct and indirect) and the closing elements are of the correct type and are complete and tight physical inspection; visual inspection. 10. The surfaces of the flanges (joint) are clean and non-degraded and the linings, if any, are satisfactory 11. The dimensions of the anti-fouling between the tiles are within the maximum permissible values 12. The nominal characteristics, the type and position of the lamps are correct 13. The electrical connections are tight 14. The condition of the carcass gaskets is satisfactory 15. Capsule and sealing devices are not damaged 16. Restricted breathing capsule is satisfactory 17. Engine fans have sufficient clearance to the housing and / or defenders 18. Breathing and drainage devices are satisfactory B. INSTALAŢII 1. The type of cable is appropriate 2. There is no obvious damage to the cable 3. Sealing columns, tubes, pipes and / or pipes is satisfactory
1/2 INSPECTION SHEET FOR EX d / Ex e / Ex n Installation
Type of inspection: ** ........................................................... Degree of Control: *** ...
Type of equipment / plant: ............................................................................................. Place where is installed / Ex zone: ................................................................................. Date of inspection: ............................................... ... .................................................... * Specify the type of Ex installation; ** It will be completed, as the case may be: the initial phase, on commissioning, the periodic phase of the survey; *** It will be completed as required: Detailed, Visual, Rigid CHECKING Result X/O 0 1 A. EQUIPMENT 1. The equipment meets requirements regarding the location EPL / Zone 2. The equipment group is correct 3. The temperature class of the equipment is correct 4. The identification of the circuitry of the equipment is correct 5. Circuit identification is available 6. Capsulation, glass parts and glass-gas seals on metal and / or components are appropriate 7. There are no unauthorized changes 8. There are no visible unauthorized changes 9. The screws, cable entries (direct and indirect) and the closing elements are of the correct type and are complete and tight physical inspection; visual inspection. 10. The surfaces of the flanges (joint) are clean and non-degraded and the linings, if any, are satisfactory 11. The dimensions of the anti-fouling between the tiles are within the maximum permissible values 12. The nominal characteristics, the type and position of the lamps are correct 13. The electrical connections are tight 14. The condition of the carcass gaskets is satisfactory 15. Capsule and sealing devices are not damaged 16. Restricted breathing capsule is satisfactory 17. Engine fans have sufficient clearance to the housing and / or defenders 18. Breathing and drainage devices are satisfactory B. INSTALAŢII 1. The type of cable is appropriate 2. There is no obvious damage to the cable 3. Sealing columns, tubes, pipes and / or pipes is satisfactory