Nothing Special   »   [go: up one dir, main page]
Scribd Logo
Upload

Welcome to Scribd!

  • 68 views

    Engineering Drawing Questions SET C

    Uploaded by

    Ankit Gautam
    The document is an exam for a course in engineering drawing. It contains 5 questions: 1) Draw an isometric view of an object and indicate dimensions. 2) Draw a perspective view of a solid square prism with specified dimensions and orientation. 3) Make an offset section view from a given figure. 4) Make top and sectional front views of a double row, zig-zag type, double strap butt riveted joint or sketch graphical symbols. 5) Draw assembled sectional front and side views from a given detail drawing.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd

    Engineering Drawing Questions SET C

    Uploaded by

    Ankit Gautam
    68 views3 pages
    The document is an exam for a course in engineering drawing. It contains 5 questions: 1) Draw an isometric view of an object and indicate dimensions. 2) Draw a perspective view of a solid square prism with specified dimensions and orientation. 3) Make an offset section view from a given figure. 4) Make top and sectional front views of a double row, zig-zag type, double strap butt riveted joint or sketch graphical symbols. 5) Draw assembled sectional front and side views from a given detail drawing.

    Original Description:

    Copyright

    © © All Rights Reserved

    Available Formats

    DOCX, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document is an exam for a course in engineering drawing. It contains 5 questions: 1) Draw an isometric view of an object and indicate dimensions. 2) Draw a perspective view of a solid square prism with specified dimensions and orientation. 3) Make an offset section view from a given figure. 4) Make top and sectional front views of a double row, zig-zag type, double strap butt riveted joint or sketch graphical symbols. 5) Draw assembled sectional front and side views from a given detail drawing.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    68 views3 pages

    Engineering Drawing Questions SET C

    Uploaded by

    Ankit Gautam
    The document is an exam for a course in engineering drawing. It contains 5 questions: 1) Draw an isometric view of an object and indicate dimensions. 2) Draw a perspective view of a solid square prism with specified dimensions and orientation. 3) Make an offset section view from a given figure. 4) Make top and sectional front views of a double row, zig-zag type, double strap butt riveted joint or sketch graphical symbols. 5) Draw assembled sectional front and side views from a given detail drawing.

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    of 3

    TRIBHUVAN UNIVERSITY

    INSTITUTE OF ENGINEERING Exam Internal assessment SET C


    PULCHOWK CAMPUS 2070 Level BE Full marks 40
    Shrawan 30 Programme BME Pass marks 16
    Year/
    Subject: Engineering Drawing Part
    II (ME451) I/II Time 3 hrs

    1. Draw an isometric view of an object shown in figure below (Fig1) and indicate dimensions.[10]
    2. A solid square prism of 30 mm side and height 60 mm with its base on the ground plane such that
    its rectangular faces are inclined at 45 degree to the picture plane and the vertical edge nearer to
    the PP is 15 mm behind it. The station point is 60 mm in front of PP, 100 mm above ground plane
    and lies in the central plane, which passes from the center of prism. Draw perspective view of the
    prism. [5]
    3. With free hand sketch, make offset section at A-A. (Fig2) [5]

    Fig 1 Fig 2
    OR
    Determine limits, tolerance, allowance and type of fit designated by 50S6/h12. The fundamental
    deviation of hole is 0.034mm and shaft is 0.000mm. International tolerance grade for 6 and 12 are
    0.016mm and 0.250mm respectively.
    4. In free hand sketch, make top view and sectional front view of double row, zig-zag type, double
    strap, butt riveted joint. [5]
    OR

    Sketch freehand the graphical symbol of following.

     Battery  Nipple  Rectifier  Tee-


     Plug  Cap  Reducer straight size
     Union  900 elbow  Check
    valve

    5. Draw the assembled sectional front view and side view from the following detail drawing shown
    in figure 3. [15]

    You might also like