4DVR65B Manual
4DVR65B Manual
4DVR65B Manual
User s M anual
DVR
CAUTION!
RISK OF ELECTRIC SHOCK, PLEASE DO NOT REMOVE COVER
WHEN POWER CONNECTED. NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING
TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE
THIS APPLIANCE TO RAIN OR MOISTURE.
NOTE: This equipment has been tested and found to comply with the
limits for a Class “A” digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful
interference to radio communications.
This Class A digital apparatus meets all the requirements of the FCC
Regulations.
1
LIMITATION OF LIABILITY
This users’ manual is supplied ‘as is’, with no warranties, be it expressed or implied,
including, but not limited to, the implied warranties of merchantability, suitability for
any exact purpose, or non-infringement of any third party’s rights.
DISCLAIMER OF WARRANTY
The supplier shall not be liable to any party or any person, except for replacement or
reasonable maintenance of this product, for the cases, included but not limited to the
following:
Any damage or loss, including but not limited to: direct/indirect, consequential,
special, exemplary use arising out of or related to the product;
2
SAFETY INSTRUCTIONS
Read these instructions and keep them in a safe place for future reference.
Please refer all work related to the installation of this product to qualified service personnel
or system installers.
Do not operate the appliance beyond its specified temperature, humidity or power source
ratings.
Use the appliance at temperatures between 0oC ~ +45oC (32oF ~ 113oF) and humidity below
85%.
The input power source for this appliance is between 100 ~ 240 VAC/50 ~ 60 Hz, 12V DC.
Install the unit away from heat sources such as radiators, heat registers and stoves.
Installation of the unit near consumer electronics devices, such as stereo receiver/amplifiers
and televisions, is permitted as long as the air surrounding the terminal does not exceed the
above mentioned temperature range.
It is possible to damage hard drives if they are moved while their motors are still running.
To allow the hard drive to spin down and park its heads, wait at least 10 seconds after
disconnecting power before moving the unit.
To avoid shock and vibration damage to the internal hard drive, do not move the unit while
it is plugged in.
Do not place the unit in an enclosed area where the cooling vents are blocked or impede the
flow of air through the ventilation openings.
Protect the power cord from being stepped on or pinched particularly at plugs and the
points where they exit from the apparatus.
Do not drop metallic parts through slots. This could permanently damage the appliance.
Turn the power off immediately and contact qualified service personnel for service.
Handle the appliance with care. Do not drop or shake, as this may damage the device.
Do not expose the appliance to water or moisture, nor try to operate it in wet areas. Do not
install the unit in an area where condensation occurs. Do not operate with wet hands. Take
immediate action if the appliance becomes wet. Turn the power off and refer servicing to
3
qualified service personnel. Moisture may damage the appliance and also cause electric
shock.
Do not use strong or abrasive detergents when cleaning the appliance body. When the dirt is
hard to remove, use a mild detergent and wipe gently.
Do not overload outlets and extension cords as this may result in a risk of fire or electric
shock.
Please make a note of your settings and save them. This will help when you are required to
change the system configuration, or when an unexpected failure or trouble occurs.
COPYRIGHT STATEMENT
All rights reserved. No part of this publication may be reproduced in any form or by any means,
transcribed, translated into any language or computer language, transformed in any other way,
stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical,
recording, photocopying or otherwise, without the prior written permission of the owner.
4
Table of Contents
LIMITATION OF LIABILITY ........................................................................................................ 2
DISCLAIMER OF WARRANTY...................................................................................... 2
SAFETY INSTRUCTIONS.............................................................................................. 3
Table of Contents ....................................................................................................................... 5
1. YOUR DVR AT A GLANCE..................................................................................................... 9
2. Contents of the Box.............................................................................................................. 10
2.1 Getting Started Check-List ..................................................................................... 10
3. Hardware.............................................................................................................................. 11
3.1 Front Panel (Please take actual machine model as quasi) ......................................... 11
3.2 Back Panel (Please take actual machine model as quasi)............................................ 12
3.3 Remote Control ....................................................................................................... 14
3.4 Hardware Installation .............................................................................................. 15
3.4.1 Basic Connections ....................................................................................... 15
3.4.2 Installing Hard Disk Drive............................................................................ 16
3.4.3 PTZ Control Connections............................................................................ 17
4. Getting Started and the Main Screen ................................................................................... 17
4.1 The Main Screen ..................................................................................................... 18
4.1.1 Displaying a Single Channel....................................................................... 18
4.1.2 Status Bar...................................................................................................... 19
4.1.3 Tool Bar.......................................................................................................... 19
4.2 Tool Bar Menu Options ........................................................................................... 21
4.2.1 System Configuration .................................................................................. 21
4.2.2 Manual Recording ........................................................................................ 21
4.2.3 Video Playback ............................................................................................. 22
4.2.4 Video Backup................................................................................................ 25
4.2.5 Video Clip ...................................................................................................... 26
4.2.6 PTZ Control................................................................................................... 27
4.2.7 Screen View Modes ..................................................................................... 30
4.2.8 Screen Layout Adjustment .......................................................................... 30
4.3 Channel Status Display .......................................................................................... 30
5. DVR Settings........................................................................................................................ 31
5.1 Menu Tree ................................................................................................................ 31
5.1.1 Menu Options ............................................................................................... 32
5.2 System Settings....................................................................................................... 32
5.2.1 Language ...................................................................................................... 33
5.2.2 Video Standard ............................................................................................. 33
5.2.3 VGA Settings................................................................................................. 33
5.2.4 Time Format.................................................................................................. 33
5.2.5 Time Setting .................................................................................................. 33
5.2.6 Password Setting ......................................................................................... 34
5.2.7 DST ................................................................................................................ 34
5.2.8 HDD Overwrite ............................................................................................. 34
5.2.9 Other Settings............................................................................................... 34
5.2.10 Add User...................................................................................................... 36
5.2.11 Delete User ................................................................................................. 36
5.2.12 Online User Manage.................................................................................. 37
5.2.13 Authority Management .............................................................................. 37
5.2.14 Preview Cruise ........................................................................................... 38
5
5.2.15 DVR ID Number ......................................................................................... 38
5.2.16 Lock Camera .............................................................................................. 38
5.2.17 Resource management--Optional............................................................ 39
5.2.18 Spot Setting--Optional ............................................................................... 39
5.3 Record Setting ......................................................................................................... 39
5.3.1 Video Channel .............................................................................................. 40
5.3.2 Record Schedule.......................................................................................... 40
5.3.3 Record Quality.............................................................................................. 42
5.3.4 Record Frame Rate ..................................................................................... 42
5.3.5 Record Source.............................................................................................. 42
5.3.6 OSD Setting .................................................................................................. 42
5.3.7 Record Resolution........................................................................................ 43
5.3.8 Sub Code (Advanced Setting) .................................................................... 43
5.4 Video Settings.......................................................................................................... 43
5.4.1 Camera Channel .......................................................................................... 44
5.4.2 PTZ Protocol ................................................................................................. 44
5.4.3 PTZ Baud Rate............................................................................................. 44
5.4.4 PTZ ID ........................................................................................................... 44
5.4.5 Color Setting ................................................................................................. 45
5.4.6 Motion Detection .......................................................................................... 46
5.4.7 Privacy Mask................................................................................................. 47
5.4.8 Motion Handling............................................................................................ 48
5.4.9 Video Loss Handling .................................................................................... 49
5.4.10 Channel Name Setting .............................................................................. 50
5.4.11 Camera Offset............................................................................................. 51
5.5 Net Settings.............................................................................................................. 51
5.5.1 Network ......................................................................................................... 52
5.5.2 IP Address ..................................................................................................... 52
5.5.3 Subnet Mask ................................................................................................. 52
5.5.4 Gateway ........................................................................................................ 52
5.5.5 HTTP Port ..................................................................................................... 52
5.5.6 Command Port ............................................................................................. 52
5.5.7 Media Port..................................................................................................... 52
5.5.8 PPPOE Settings ........................................................................................... 53
5.5.9 PPPOE IP...................................................................................................... 54
5.5.10 DNS Address .............................................................................................. 54
5.5.11 DDNS........................................................................................................... 54
5.5.12 Auto Register .............................................................................................. 54
5.5.13 Email Settings............................................................................................. 55
5.5.14 Mobile Port.................................................................................................. 57
5.5.15 UPnP ........................................................................................................... 57
5.5.16 FTP Setting ................................................................................................. 57
5.5.17 IP Access..................................................................................................... 58
5.5.18 Time SYNC ................................................................................................. 58
5.6 Alarm ......................................................................................................................... 59
5.6.1 Alarm Input Channel .................................................................................... 60
5.6.2 Alarm Input Type .......................................................................................... 60
5.6.3 Event Handling ............................................................................................. 60
5.6.4 Alarm Setting................................................................................................. 61
5.6.5 Alarm Zoom Out ........................................................................................... 61
6
5.6.6 Device exception action .............................................................................. 62
5.7 Maintenance ............................................................................................................ 62
5.7.1 Log View........................................................................................................ 63
5.7.2 Upgrade......................................................................................................... 64
5.7.3 HDD Manage ................................................................................................ 64
5.7.4 USB Manage................................................................................................. 65
5.7.5 Copy Setting to USB.................................................................................... 65
5.7.6 Load Setting from USB................................................................................ 66
5.7.7 Auto Maintain ................................................................................................ 66
5.7.8 HDD Capacity ............................................................................................... 66
5.7.9 Hardware Version......................................................................................... 66
5.7.10 Software Version ........................................................................................ 66
5.7.11 Software Release Date.............................................................................. 66
5.7.12 DVR ID ........................................................................................................ 66
5.8 Save Settings........................................................................................................... 67
5.8.1 Save & Exit.................................................................................................... 67
5.8.2 Exit ................................................................................................................. 67
5.8.3 Restore defaults ........................................................................................... 67
5.8.4 Logout............................................................................................................ 67
6. Web Browser Operation ....................................................................................................... 68
6.1 Enabling Download of an Unsigned ActiveX Control.......................................... 68
6.2 Web Browser Login Screen ................................................................................... 68
6.3 Web Browser Main Window................................................................................... 69
6.4 Tools Bar Items ........................................................................................................ 71
6.4.1 Parameters.................................................................................................... 71
6.4.1.1 Server ................................................................................................. 72
6.4.1.2 Channel .............................................................................................. 73
6.4.1.3 Serial................................................................................................... 78
6.4.1.4 Alarm................................................................................................... 79
6.4.1.5 User .................................................................................................... 81
6.4.1.6 Device................................................................................................. 82
6.4.1.7 State.................................................................................................... 84
6.4.2 Talk-back ....................................................................................................... 84
6.4.3 Playback........................................................................................................ 84
6.4.4 Device Log .................................................................................................... 88
6.4.4.1 All Query Kinds .................................................................................... 88
6.4.4.2 Query Kind by Time ............................................................................. 89
6.4.4.3 Query Kind by Type.............................................................................. 89
6.4.4.4 Query Kind by Time and Type .............................................................. 90
6.4.5 Local Storage................................................................................................ 92
6.4.6 Screen View Buttons.................................................................................... 92
6.5 PTZ Control Panel................................................................................................... 92
7. iPad support ......................................................................................................................... 94
8. Mobile Phone Support........................................................................................................ 104
8.1 Windows Mobile .................................................................................................... 104
8.2 Symbian S60 3rd Phone ...................................................................................... 105
8.3 List of Symbian Supported Mobile Phones ........................................................ 108
8.4 Apple iPhone.......................................................................................................... 110
I. For “KWeye+”............................................................................................. 110
II. For “KWeye”.............................................................................................. 110
7
8.5 Blackberry Mobile.................................................................................................. 112
8.6 Android (Google Phone) ....................................................................................... 120
I. For “KWeye+”............................................................................................. 120
II. For “KWeye”.............................................................................................. 124
8.7 FAQ ......................................................................................................................... 127
Troubleshooting...................................................................................................................... 128
Appendix 1 Estimating HDD Capacity.................................................................................... 130
Appendix 2 Compatibility Table for HDDs............................................................................... 131
Appendix 3 List of Compatible Portable USB DVD Recorders............................................... 131
Appendix 4 Compatibility Table for USB flash drives.............................................................. 131
Appendix 5 How to Use Auto ID-"Plug n play" Quick Guide................................................... 132
Appendix 6 How to Use RTSP ............................................................................................... 134
8
1. YOUR DVR AT A GLANCE
Product Overview
16 Channel
Model 4 Channel 8 Channel 16 Channel
(only CIF)
Record method Scheduled Record(Manual Record, Motion Detection, Sensor Trigger)Support Privacy Mask
Up to 1 TB for each one, SATA
interface HDD x2 or HDD Up to 1 TB for each
SATA Interface support 2TB
HDD Interface x1+DVD+RW(1U),SATA one, SATA interface
interface HDD*4 or HDD x2
HDD*2+RW(2U)
Network Protocol TCP-IP/ DHCP/DDNS/PPPOE/E-Mail
IE Browser Live Monitor, Configuration, Download Video
Network Function
Mobile Phone Surveillance
USB 2.0 Interface Mouse / Portable Mobile HDD/ Flash Drive/ DVD Burner/ Firmware Upgrade
Playback Method Normal Play, Fast Forward, Rewind, Single Step
RJ45 10M/ 100M /1000M RJ45 10M/ 100M
Network Interface RJ45 10M/ 100M Ethernet Auto Detect
Ethernet Auto Detect Ethernet Auto Detect
PTZ Protocol* PELCO-P ,PELCO-D, Samsung, Panasonic
Video Backup MP4, AVI or H.264 Raw
Power Adapter DC 12V Adapter
Power Consumption 10~15W
Operating Temperature -10℃~+40℃
Operating Humidity 10%~90% RH
315(W) * 224 (D) * 52 (H)
315(W) * 224 (D) * 52 mm(some DVR is not as the 435(w)*340(D)*55(H)mm(1U)
Dimensions*
(H) mm same dimension as this ,it 435(w)*340(D)*90(H)mm(2U)
depends on your device)
9
*Model dependent
Congratulations on purchasing your state-of-the-art Digital Video Recorder (DVR) offering
industry’s best triplex functionality with video/audio recording, playback, and network
capability. Your new device allows you to run all three functions simultaneously, streamlining
the use of your CCTV system and boosting the security level of your home, business or social
venue. You can access live or recorded feed from your standard or PTZ cameras immediately at
the location of the DVR installation, or anywhere in the world using web-browsers or a mobile
phone*. The video may be stored at a remote location for safety.
(*Some limitations apply to web- and phone-based features, please see the related sections for detailed
description.)
Please get acquainted with the parts and accessories as well as the ways to use the appliance as
described in this instruction manual. If you have any questions that this guide cannot answer,
please contact your vendor or a certified specialist.
o Are the power and video in/out cables plugged in? Please see Section 3.4.1
Basic Connections for more.
o Is the HDD installed and formatted? Please see Sections 3.4.2 Installing HDD
and 5.7.3 HDD Manage for more.
o Did the DVR start recording? Please see Section 4.2.2 Manual Recording for
more.
10
3. Hardware
11
No Alarm: Alarm reset (for portion 8 Channel and 16 Channel only,
depending on the model)
Power Off ( ): Power Off (optional, depending on the model).
Auto-Sequence ( ): Press it to enable auto sequencing (optional, depending on the
model).
8. IR Window Infra-red sensor for remote control
8 CH (1U Small)
6 13
1 4 5 7 8 9 11 10
16 CH (Only CIF)
13 4 5 7 10
8 14 1 6 9 12
16 CH (CIF & 1U)
7 13 13 10 4 5
1 15 6 8 9 16 12
12
16CH (CIF & 2U)
4 5 9
7
13 15 13 6 8 16 10 12
1. USB connectors
Use these USB ports to connect the mouse and backup devices (flash drive, DVD recorder).
Note: On some models, the USB port is on the side panel or on the front panel.
2. Audio Output Connector
1 channel audio output, RCA (2Vp-p, 600Ω)
3. Audio Input Connectors (AUDIO IN 1-4)
4 channel audio input, 4CH-RCA (2Vp-p, 600Ω)
4. Video Input Connectors (1-4/1-8/1-16)
4-/8-/16- channel video input, BNC (1Vp-p, 75Ω)
5. Video Output Connector
Video output to display monitor, BNC (1Vp-p, 75Ω)
6. VGA Connector (optional)
For connecting VGA/LCD monitor
7. Ethernet Connector
RJ-45 10/100 Base-T Ethernet network
8. Alarm Input Connectors (ALARM IN 1-4/1-16, G)
For connecting to external sensor device
Alarm Output Connectors (ALARM OUT COM-NO)
For connecting to external alarm device
RS-485 Connector
For connecting PTZ camera control (RS485: A, B)
9. Power Input Socket
Please choose a correct power according to the introduction pressed on the device)
10. Power Switch
11. Cooling fan
The fan is used to cool HDD.
12. Ground
13. Audio Input / Output Connector (Only for 8-Channel and 16-Channel)
Connect with attached DB9 PIN to RCA cable adapter for audio input/output.
14. Microphone ---- (optional)
13
Connect microphone to talk back.
15. HDMI---- (optional)
High definition multimedia interface.
16. Spot Video Out---- (optional)
Auto Cruise each channel.
2 Play/Pause ( ): Opens video search and playback menu. When the playback mode is
activated, press this button to play/pause playback.
7 Lock ( ): you will logout the system if you press this button.
8 Numerical Button: Using these buttons, you can choose to output video on your monitor
either as a full-screen view of each of the cameras individually (Channels 1 through 9).
12 ENTER: This button is used as the “enter” key in most circumstances. And on live view
press this button to bring up tool bar.
14 Quad ( ): Press this button to switch display modes. There are 4-CH mode, 6-CH
mode, 8-CH mode, 9-CH mode. You can use it according to your demand.
Can be used as FN icon too, Assistant function: In motion detection area and record mode,
press it to enter or quit paste state. And in playback search, press it can be set the start time or
end time to playback.
14
3.4 Hardware Installation
It is recommended that the installations described below are carried out by qualified personnel.
Power
Please use the 12V DC adapter supplied for connecting your DVR device with the
power source.
Alarm Input / Output
Connect Alarm In 1-4 / Alarm In 1-16 to N.O. (Normally Open) or N.C. (Normally
Closed) alarm connectors and one Ground connection. Connect Alarm Out to the
corresponding connections and Ground accordingly.
16 channel
4/8 channel
For detailed description please see Section 5.6.2. Alarm Input Type
15
Ethernet
For remote access to the video images from your cameras via LAN or the Internet,
please connect the standard RJ-45 twisted-pair Ethernet cable to the Ethernet connector.
USB
For connecting the mouse, USB flash drive, USB portable HDD, USB portable DVD
Recorder (for the list of compatible HDDs see Appendix 2, for the list of compatible
DVD Recorders see Appendix 3).
NOTE: The device only supports FAT32 file system on the USB devices.
Before you can record onto your HDD it should be formatted by the DVR
system, because standard PC formatting is not compatible. It can be done
in the Maintenance Tab of the Tool bar Main Menu. Please refer to
Section 5.7.3 HDD Manage for the detailed description of this process.
Depending on the size of your HDD, the format process can take several
Power connector
Data connector
Your HDD should be installed inside the DVR. Please connect the HDD in the standard way.
All necessary cables are delivered with the DVR. Use instructions that came together with the
hard drive for exact wiring. Please connect the power cable to the appropriate socket, and the
data cables to their corresponding connectors.
For the list of HDD drives tested for compatibility please see Appendix 2.
16
3.4.3 PTZ Control Connections
Connect the PTZ control jacks to the corresponding RS485 A and B interfaces on the rear
panel.
For detailed description of PTZ protocols, baud rates and IDs, please refer to
the setup section in the PTZ manual.
When you enter the system you will be asked to log in. Select your user account and enter the
password in order to operate the device. You can choose user accounts by clicking arrow
buttons on both sides of the account field (or using arrow keys on your remote control), and
enter the password using the numerical keypad in the lower part of the “Input Password” screen.
Press OK to confirm or Cancel to clear the field and enter another value.
By default the system has two users: Admin and User with preset passwords. The Admin
account allows you to change critical system settings.
17
The default password for Admin is “888888”, for User: “666666”
You can always change your password in the System Settings of the System Configuration
Menu (see Section 5.2.6 Password Setting).
To enter a single channel view you can press the corresponding numerical buttons on the
remote (channel number is displayed in the top left corner of each window, alternatively you
can do so by left double-clicking on the desired window, or by choosing the button in the
on-screen remote control..
In order to return to the multi-screen view you could either double-click on the screen again or
press the single/multiple view button either on the remote control or the front panel.
You can choose to display the Status Bar, Tool Bar or neither of them by single right-clicking
on the screen. These three options alternate in sequence.
18
4.1.2 Status Bar
Located at the bottom of the screen, the Status Bar may be called up by right-clicking anywhere
in the screen.
Status Bar
The Status Bar offers the following information:
The four top icons indicate the alarm input status for each of the four windows. When the alarm
is triggered, the color of the corresponding icon changes to red
The icon below indicates alarm output. When alarm output is activated, it changes its color to
red.
The other three information sectors denote, in order: HDD usage (percentage), number of
cameras which connect the system via the network/Internet (NET:X), and current date/time in
the YYYY-MM-DD HH-MM-SS format.
19
Tool Bar
To display the Tool Bar you can toggle the “No Bar” Æ Status Bar Æ Tool Bar options by
right-clicking the mouse anywhere in the screen, or by pressing the Enter button on the front
panel or the remote control:
The functions of the buttons present in the Tool Bar are as follows:
Use this button to hide the Tool Bar and return to the Status Bar.
Next page
System configuration
Manual recording
PTZ operation
Cancel alarm notification. Clicking this button will bring up a message showing current
alarm information.
Quick playback
Shut down
20
, , */ or /
* , /
, * Switching between screen display modes.
“Single channel” Æ “four channels” Æ / * “six channels” or / * “eight channels” (for 8CH and
16CH), Æ “nine channels” (for 8CH and 16CH), Æ / *“16 channels” (only for 16CH).
TV/Monitor: Press the “ESC->CH1->ESC” button or click “ ” on the toolbar, and this
will switch the main menu between CVBS video output and VGA video output, or switch the
main menu between CVBS video output and HDMI output.
PIP 1*1: This feature displays the video from one channel in a small inset window, while
another channel is displayed in full-screen view.
PIP 1*2: This feature displays two channels in small, inset windows, while another
channel is displayed in full-screen view.
See the following subsections for a detailed description of each of these functionalities.
Pressing this button will bring up a screen for setting up all system configurations. You
can adjust such settings as System, Record, Video, Net, Alarm, Maintenance and Save.
Please refer to Section 5. DVR Settings for the detailed description of these settings.
There are three ways of recording live video/audio feed from your cameras: manual
recording, scheduled recording, and alarm recording.
21
If the recording schedule is in conflict with manual recording, the manual recording will be
processed first until stopped. Recording modes are displayed in the top right corner of the
respective screen. Manual recording mode is indicated onscreen with the grey icon .
For color indication of other recoding modes see Section 4.3 Channel Status Display.
For detailed description of scheduled and alarm recording see Section 5.3 Record Settings.
Description of the manual recording function follows.
In order to record a video/audio feed, please select the Manual Record button in the Tool Menu.
Alternatively you can use the REC button on the remote or the front panel. Pressing this button
again will stop the manual recording process.
You can select the channels you wish to record individually or you can choose to have them all
recorded simultaneously. Press OK to confirm, or press Cancel to undo your choice.
Pressing this button will bring up a dialog window in which you can select the recording which
you can playback or backup. Each of these options is described below. Up to 4 channels can be
selected for playback with 4-ch DVR, 16-ch DVR (only CIF). And up to 8 channels can be
selected for playback with 8-ch DVR (CIF). And up to 16 channels can be selected for
playback with 16-ch DVR with CIF.
Selecting the time frame you wish to playback
22
In order to playback a certain video feed from a particular camera, you first need to indicate
what time and which camera you wish to receive this information from.
Set up the year, month and day of the desired recording. If you are using the remote, you can
navigate between fields using and buttons and modify the time with the help of the ▲
and ▼ buttons. Press Enter to confirm your selection. When using the mouse, simply position
the mouse over the field and use directional buttons which will appear above and below the
field to modify the values. After selecting the day, please click Search to search for the
recordings from that day.
Select the Start and End time on the time line positioned against the available channels (you
can choose which channel to view by selecting the checkbox next to each channel). Up to 4
channels can be selected for playback. The start and end times of the recording you wish to
view are indicated by two vertical lines on the time line. When you are using the remote and try
to go to the desired line using directional buttons. If you would like to fine-tune the required
time, you can use the buttons to zoom in / zoom out of the time line. Alternatively, you
can move along the time line using and buttons. Time values will be shown above the
time line.
Using mouse: left-click once to setup the start time, the subsequent left-click will indicate the
end time, and the right-click will cancel the marked time.
Using front panel: you can navigate between fields using and buttons and modify the
time with the help of the ▲ and ▼ buttons. When moves to the channel, press Enter to
confirm or cancel your channel selection. If you would like to fine-tune the required time, you
can use the buttons to zoom in / zoom out of the time line. Using and buttons
to switch pages when it zooms out too large.
After searching, press [ ] or [ ] or [Fn] button to choose start time line. Using and
buttons to move the time line. Press [ ] or [ ] or [Fn] again to popup the second
time line as the end time line. Also can use and buttons to move the time line. Then
press [ ] or [ ] or [Fn] to confirm the time.
23
The available recordings will be represented by differently colored bars on the time line
depending on the type of the recording (Blue: common recording, Green: motion detection
triggered recording, Red: alarm triggered recording, Grey: manually made recording).
To play the selection, press the Play button (or navigate to it and press Enter on the remote
control or the front panel): the selected channels will playback in the standard view windows in
their respective positions on the monitor screen.
Playback Control
In the playback mode you can see the playback control panel as well as the date and time of the
played file.
Stop
Fast / slow forward
The available speeds are 1x, 8x 16x, 1/2x and 1/4x
Frame-by-frame view
Toggle single camera view and 4/9* camera view (*depending on the model).
Video editing
Backup
24
4.2.4 Video Backup
Back up can be initiated from the same dialog window as the playback function.
To back up the recorded footage, you first need to indicate which cameras and time interval you
want to save to an external source. Please set the start and end time as described in the previous
section.
After click the Backup button which brings up the “Backup” dialog window. If the system
cannot recognize the connected devices or none are connected, you will see a warning message
“No Available Device!”
The system will automatically detect all available backup devices and display them in the
Backup Device field (positioning the mouse over this field or entering it with the help of the
25
arrow buttons will allow you to view the available choices. By pressing arrows on each side of
the field, you can toggle between the options).
Currently you can connect such external media as USB flash drives, portable USB HDDs and
USB DVD recorders. For the list of DVD burners tested for compatibility, see Appendix 3.
The system only supports the FAT32 file system for USB flash
drives and HDDs
You may also choose between the types of recorded video formats to be backed up, selecting
between the H.264 Raw, MP4 and AVI formats.
If you are saving your backup data in the MP4 format, the system will automatically record
special decoder components onto the USB flash drives or DVD Discs along with the video file.
After installing this component on your computer you can play saved video files with the
Windows Media Player.
To install the decoder components on your computer, locate the compressed file
WMP_MP4Player.rar inside the USB flash disk or CD/DVD where you saved the video file.
Decompress WMP_MP4Player.rar and execute Install Filter.bat to install the decoder
components.
After installing the necessary software, you can view the saved video using the Windows
Media Player.
When backup in H.264 format, the stored video files can be played by H.264 player
because it is a standard H.264 type file. For example, download H.264 player from
http://www.videolan.org/vlc. Then, it can be played by VLC Media Player.
When backup in AVI format, the stored video files can be played by Windows Media
Player.
26
Click the button in the playback control panel when you want to begin to edit the video,
then the button will change to , when you want to end the editing, click the button , and
it will change to . Then insert the USB device and click the button enter into the
following interface.
Choose the file, click “Backup” and choose the backup format, click “backup” and then the file
will be saved into your USB device.
Choose the file, click “DEL” and the file will be removed from the list. In addition, if you exit
the playback and the list will be cleaned automatically.
You can use this function if your DVR is connected to a PTZ camera (Pan-Tilt-Zoom). Pressing
the PTZ control button will bring the corresponding video feed into the single-screen
mode. In the top left corner of the screen you will see the special PTZ menu. Directional
27
buttons will determine the rotation of the camera, and the drop-down menu, called up by the
button, will show the functional panel.
Functions of these menu options may vary depending on the make and model of the PTZ
camera you are using. For detailed description of the available options please refer to the
manual of your PTZ camera.
28
Click to focus-in and focus-out (this function is disabled for
5 Focus
cameras with automatic focus).
Click to make the image brighter or darker (this function is
6 Iris
disabled for cameras with automatic iris adjustment).
Open/close auxiliaries.
29
4.2.7 Screen View Modes
, /
, * or * , , /
*
Allow you to switch between single/multiple screen views (4-screen, *6-screen, *8-screen,
9-screen, *16-screen, * depending on the model).
You can use the available buttons to re-position the layout of the whole screen image on the
monitor (all 4/*9/*16 (*depending on the model) windows as a unit or the single-view
window).
30
5. DVR Settings
5.1 Menu Tree
31
5.1.1 Menu Options
In order to modify/adjust system configuration, you need to enter the System Menu by pressing
the System Configuration button in the Tool Menu.
You will see the dialog window with settings for all systems and options available in your DVR.
The settings are subdivided into 7 subsections, each with its own tab: System, Record, Video,
Net, Alarm, Maintenance and Save. Below is the detailed description of these settings.
This tab provides general system settings for operating your DVR. Titles of the menu list items
are located on the left, and the corresponding changeable or non-changeable values are
represented in the fields to the right. You can:
(a) Select the values from the list (toggling the preset data by pressing the arrows on each side
of the field);
(b) Input the required data after entering a customized window by pressing the [>>] button in
32
some of the fields; or
(c) Familiarize yourself with the existing non-changeable settings.
When entering the fields using the remote control directional keys or the DVR front panel, as
well as when positioning the mouse over them, a short description of the setting in question
will appear at the bottom of the window.
Several tabs have options that are positioned on more than one window, and you can navigate
between them by pressing either the “Next Page” or “Advanced Settings” buttons.
5.2.1 Language
Use this option to change the language of the DVR menu text and the On-Screen Display. This
action takes effect immediately and does not require saving and exiting this menu.
In order to avoid possible confusion with the time stamps of the recorded and currently
recording files, it is advised that you stop all ongoing recording processes before altering
the system time and restart recording with the new settings.
33
5.2.6 Password Setting
You are allowed to modify the passwords of both Administrator and User accounts. You have
to be logged in as Administrator to be able to introduce such changes, and the User can only
change the user account password. Make the selection of the relevant account and enter the new
password using the numerical keyboard, after which you can either confirm (OK) or reject
(Clear) the input data.
5.2.7 DST
Daylight saving time setting. Users can set the starting time and ending time of DST. For
example, in the following screenshot on the below, the starting time is 18:00:00 on Thursday of
the first week in September, and the ending time is 05:00:00 on Friday of the first week in
September.
In the next two pages there are these items: Add User, Delete User, Online User Manage,
Authority Manage, password setting, DVR ID Number, Preview Cruise, Menu overtime,
Lock Camera, *Resource management (resource management is only for 8CH), and
*Spot setting (for 16CH with CIF).
34
You can return to the original screen by pressing Common Setting button in the bottom right
35
5.2.10 Add User
It allows add users. Administrator can write name and click button “OK” directly to add users.
It can add 7 users at most.
It shows all of user names, managers can choose one of the name and click “DLL” to delete
this user, and then click “OK” to make it effective.
36
5.2.12 Online User Manage
It shows the information of online users,including user name, login mode of the user, login
time and net flux. And the administrator can make the online user disconnection.
[Remote Authority]: This is a very important function for remote operation of the DVR. The
Administrator can use this function to set each user’s remote access permissions, such as access
to Setting, Clear Alarm, Shutdown, Remote PTZ Control, Remote Manual Record, Remote
Playback, Remote Preview from a computer that is not on the local network (see the following
figure).
37
After introducing new configurations you can confirm (OK) or reject (Cancel) the changes.
38
5.2.17 Resource management--Optional
This function is only for 8CH model.
39
images onto the HDD. Following is the description of the possible options.
Please note that manual recording overrides all record settings and will be carried on until
stopped by the operator.
40
①. The current recording channel number undergoing modification.
In the example, the introduced changes will be applied to all available channels.
You can use either directional buttons for selecting the fields or the Enter button to indicate the
desired color pattern, or, having chosen the required color code, click on the necessary hour in
the graph and drag the area in any direction to highlight several cells.
Press OK to confirm the settings. The changes will take effect after saving and exiting the
menu.
While you are using the remote control or front panel to option, button can be used to
copy the present setting to the adjacent time area with the help of ▲ and ▼, and buttons.
After setting some area’s recording type, press button to enter paste state, then paste its
setting to other areas by using ▲, ▼, , buttons. Press to quite.
41
When you select the option of motion detection recording, in order
for the actual recording to happen, it is necessary to set the motion
detection sensitivity and area. Please refer to Section 5.4.6
Motion Detection Settings for details. When alarm recording is
selected, please set the alarm triggering settings beforehand. See
Section 5.6.3 Event Handling for details.
Select quality level for recording audio/video. There are pre-defined values of Best quality
768kbps Æ High 640kbps Æ mid 512kbps Æ Low 384kbps, or alternatively, you can define
your own recording quality (Kbit/s). Pressing the [>>] button under the User Defined option
will bring up another window in which you can enter the desired values using the numeric
keypad, and confirm your input by pressing OK or reset the entered values by pressing Clear.
In this section you can choose the recording frame rate (frames per second). The pre- defined
choice is Full (30/25fps depending on whether it is NTSC/PAL) Æ 15 fps Æ 7 fps Æ 3 fps Æ
1 fps or user defined. The lower the value, the less life-like and more jerky the recorded
movements will be. On the other hand though, a lower frame rate can save a lot of HDD space.
Make your choice depending on the precision with which you want to follow the events
unfolding before your cameras.
Pressing the [>>] button, which appears under the User Defined option, will bring up another
window in which you can enter the desired frame rate values using the numeric keypad or clear
the entered values by pressing button Clear.
Since the maximum value for the frame rate is either 30 or 25 fps depending on the encoding
system, your choice may be within the limits of 1 to 30/25. Thus, even if you enter a higher
value, the resulting frame rate will be kicked back to the maximum allowed value. To confirm
your input, press OK.
42
3) Time Stamp
4) None
Make your selection navigating through these choices by using arrow button on each end of the
field.
43
5.4.1 Camera Channel
This option allows you to select the camera (channel) number whose settings you want to
modify. If you want the changes to apply to all available channels, you need to select “All”.
Make the selection by pressing the arrow buttons; the options run in a loop: 1 Æ 2 Æ 3 Æ 4 Æ
5Æ6Æ7Æ8ÆAll Æ 1, etc.
Select the PTZ device protocol. It must be consistent with the protocol of the actual PTZ
cameras installed. You can make the choice among following available options: Pelco-D,
Pelco-P, Panasonic, Samsung, Philip, Yiboer...etc. The changes will take effect after you save
and exit.
Select the PTZ device baud rate. It must be consistent with the baud rate of the actual PTZ
cameras installed. You system supports four options: 1200, 2400, 4800, 9600. The changes will
take effect after you save and exit.
5.4.4 PTZ ID
44
Select the PTZ device ID. It must be consistent with the ID of the actual PTZ cameras installed.
Make your choice of any number from 1 to 255. Please note that this is not the same as the
number of the channel to which you hook up the PTZ camera in your DVR system. The system
allows for step-by-step selection of the values by pressing the arrow buttons at each end of the
field. The changes will take effect after you save and exit.
You can adjust camera color attributes for the best image rendition. By default the values are
set at 8 as the average value. Please make your adjustments depending on the actual conditions
at the location where the camera is installed.
The values are listed in the Color Setting field of the Camera Tab in order (in the picture
below it is 8 / 8 / 8/ 8, which stand respectively for brightness, contrast, hue and saturation).
When you decide to make changes to these values, please press the [>>] button at the right end
of the field and it will take you to the full-screen image of the camera feed, with the four
abovementioned color characteristics listed in a column, allowing you to change their values.
z Hue: 1 ~ 16
z Saturation: 1 ~ 16
Position the mouse over the required field and use the floating arrows at each end of the field to
increase/decrease the values. The live feed from the camera will let you see what these
adjustments would look like in real life.
45
Right-click anywhere in the screen to leave the camera view, and go back to the previous
Camera Setting window. The new values will be displayed in the Color Setting field as
described above.
There are four options related to the degree of motion detection sensitivity:
Sometimes you need to have some regions in your camera view with the enabled motion
detection feature, while other regions in the same view should be free of this functionality. This
may be handy when, for example, the camera covers the road and an adjoining territory. While
you would like to have the motion detection working on the area near the entrance to the
building, you most likely would not like to see it triggered every time a car or truck passes on
the nearby road.
In order to select the region(s) in the camera view where the motion detection feature should be
activated / disabled, press the [>>] button at the right end of the Motion Detection field to
bring up the full-screen image of the camera feed, with a superimposed grid. You can
select/unselect each cell by a single left-click of the mouse or select multiple-cell areas by
clicking on one cell and dragging the selection in the desired direction. You can select as many
isolated areas as you wish.
Blue highlighted squares indicate areas where motion will be detected. Clear squares will
indicate areas where motion will NOT be detected.
Using front panel: After open the motion detection area setting interface, can set 192(16*12)
zones. You can move the focal point among them by using , buttons. The detail area
setting like below steps:
1. Using ▲, ▼, , buttons to move the focal point among areas, press OK button to
confirm your choice.(the color will turn to highlighted from blue).
2. Press button, and now you can paste its setting to other areas by using ▲,
▼, , buttons. Press to quite when you finished the first motion detection
area setting.
3. Repeat steps 1 and 2 to finish the second motion detection area setting.
To return back to previous menu, please right click or press ESC on front panel/remote control.
46
Motion detection plan setting
Select the date and time to plan motion the detection area or not.
Sometimes you need to have certain areas within the scope of a camera view to be unmonitored
for privacy protection, for example when it shows windows of an apartment building together
with the monitored area. Thus, you can choose to not record these select multiple regions.
You can turn this option ON or OFF in the Video menu and you can manually setup privacy
areas. Press button [>>] at the right end of the Mask field to bring up the full-screen image of
the camera feed. You can select any area to be grayed out on the live feed from the camera (and,
consequently, from the video recording made on this channel). Left-clicking and drag to select
the desired area. Right-clicking on the screen anywhere and the selected area to go back to the
main menu window. To apply the changes you need to save and exit.
You can select as many isolated (and/or overlapping) areas as you wish.
47
Please have a look at the DVR screen showing one and the same camera view with and without
privacy areas.
To unselect the privacy area or cancel this option, go back to the Video Tab of the Main Menu
and turn this function OFF in the main window.
To activate the privacy zones you had set up before this feature was turned OFF, you can
simply turn the Mask function ON in the Video menu. If nothing was changed in the layout of
the selections, the same privacy areas will appear on the screen.
To undo a privacy area, go to the Privacy Mask setup ([>>] button at the right end of the
Mosaic field) and right-click within the previously selected grayed-out area (which has a red
border if it is active) – the red border will disappear. Right-clicking anywhere but the gray area
to exit the screen and save the changes.
Channel number will be displayed at the top of the screen. There are four available options.
48
RECORD: When these options are checked, motion detection will trigger immediate
recording from the selected cameras.
ALARM ZOOM OUT: When the option is selected and one or more record channel is
selected,these record channel will touch off alarm zoom out.
ALARM OUT: Checking this option will enable the Alarm Output when motion is detected.
BUZZER: Checking this option will enable the internal buzzer when motion is detected.
UPLOAD: If you have established a remote connection between the DVR and a PC via the
internet, and you check the UPLOAD checkbox, then on detecting a motion the DVR will send
a relevant message to the IE applet (for example: “Device Alarm, Motion Alarm Channel 1”),
which will be displayed in info line at the top right corner of the IE window.
E-MAIL: After you check this option, a motion detection event will initiate an e-mail being
sent to the indicated addresses with a snapshot of that event as it was captured on the camera
(see Section 5.5.12 Email Settings for information on how to set up the list of email
addresses).
49
ALARM OUT: Checking this option will enable the Alarm Output when video loss is
detected.
BUZZER: Checking this option will enable the internal buzzer when video loss is
detected.
UPLOAD: If you have established a remote connection between the DVR and a PC via
the internet, and you check the UPLOAD checkbox, then on detecting video
loss, the DVR will send a relevant message to the IE applet.
E-MAIL: After you check this option, a video loss event will initiate an e-mail being
sent to the indicated addresses with a snapshot of that event as it was
captured on the camera (see Section 5.5.12 Email Settings for information
on how to set up the list of email addresses).
The Video Æ Advanced Setting Æ Channel Name Setting Æ [>>] button will bring up the
dialog window where you can set channel name.
50
5.4.11 Camera Offset
The Video Æ Advanced Setting Æ Channel Name Setting Æ [>>] button will bring up the
dialog window where you can set camera offset. Values can be set up from 0 to 15. And it will
take effect instantly.
Below you can find the detailed description of each option present in this menu.
51
5.5.1 Network
Your DVR supports several methods of being viewed online. No matter which method is used,
your DVR must first acquire an IP address, which it does via 2 different methods.
For exact data on your network and explanation of network settings, please contact your
network administrator or Internet service provider.
PPPOE settings for ADSL dial-up connection are also supported, please go
to the next window of the Net Tab by clicking Next Page.
5.5.2 IP Address
In this section, you can get IP address as well as set static IP address. The changes will take
effect after you save and exit.
5.5.4 Gateway
52
You can specify a different port number.
HTTP port: 80, Command port: 5050, Media port: 6050 and
Mobile surveillance port: 7050 must be open/allowed to upload
to WAN interface if the DVR is behind a Firewall server.
Next page in the Net Tab can be accessed by pressing the Next page
button in the bottom right corner of the menu screen. There are
options: PPPOE Setting, PPPOE IP, DNS address, DDNS, Auto Register, File Sharing
and Email Setting.
In a separate window, which you can bring up by pressing the [>>] button at the right end
of the PPPOE Setting field, you can input the ADSL user account name and password. You
can get this data from your Internet Service Provider. Use the keypad located in the lower
half of the PPPOE Setting screen to input this data.
53
5.5.9 PPPOE IP
These values depend on your actual account; please contact your Internet Service Provider for
details.
5.5.11 DDNS
In order to connect your DVR to the
internet, you may choose to use the
services of a Dynamic DNS service.
54
Auto Register dialog window by clicking the [>>] button, and view the Server IP, Server Port
and Interval values.
Here you can indicate multiple e-mail addresses for persons who need to receive alarm
notifications when an alarm is triggered.
Clicking the [>>] button in the E-mail Setting field will bring up a dialog window, where
you can adjust the necessary settings.
You need to enter the User name and Password of the email account from which such
notification e-mails will be sent, the recipients of these emails, as well as Server and Port
details. Please make sure the account you are indicating exists and is active.
*On some models, there will be a default email account, from which notification emails
55
will be sent. Please ensure this default email address is added to your Email Address Book
so it is not treated as spam email.
The Object Address (TO) field indicates the recipients of alarm emails, and the Revert
Address (FROM) field indicates the email account from which the message will be sent. In
the Object Address field, you can indicate multiple addresses by adding them to the list of
recipients. To do so, press the Add button. You can View the list of recipients in the Email
list window which will appear on the screen after pressing the View button.
You will be able to see the list of recipients in the table on the right, and two buttons to
manage this list on the left. The options for managing the list are: Delete and Delete All. To
save the changes click OK, to exit the window without saving, click Cancel.
Click Next Page again to go to the page as below. Including “Mobile port”, “UPnP”, “FTP
setting”, “IP access” and “Time SYNC”.
56
5.5.14 Mobile Port
This DVR allows remote access from a mobile phone. The port that the mobile phone uses is
indicated here and is by default 7050. For details on using DVR functionalities from mobile
phones please see Section 7.
5.5.15 UPnP
Set external HTTP Port, Command Port, Media port, and Mobile Port which mapped in
Internet.
Switch the UPnP to ON, then click button to map it. Show as below:
It may take you about one minute. Please wait. After that it brings up the Picture as below.
It shows you that the UPnP mapped failed or succeed. If failed, you need to map again. If
succeed, you can go to connect the internet.
[Port, User name, Password]: Install the FTP server first, then register, and remember the port,
username, and password. Entered the port, username, and password used here will be the same
57
as the ones entered on the server.
Click the button “TEST” to validate the parameters that users setup right or not.
5.5.17 IP Access
Including allow access, forbidden and disable, switch to allow access then click button to
enter it. Show as below:
User can set the time Server host, the time Sync interval and the time zone, then click
“ ” to save the setting.
58
If user clicks “Update”, the system time will proofread the time with the network server that
you setup at once.
5.6 Alarm
Next menu tab in the System Menu is Alarm. Under this tab the administrator can define how
the DVR will respond to various alarms from the alarm inputs and adjust Alarm input / output
settings.
//
59
5.6.1 Alarm Input Channel
Select alarm input channels to which the configurations adjusted below will apply. For each or
all cameras, you can setup various kinds of behavior. You have a choice of channels 1 through 4
and ALL – to have the settings apply to all channels.
This field allows you to choose between the N.O. (Normally Open) and N.C. (Normally Closed)
options.
N.O.: Normally open type. It means that in the normal state, the sensor device is kept under
constant low voltage. If output voltage changes from low to high, then the alarm is triggered.
N.C.: Normally closed type (also – “normally connected”). The normal state of the sensor
device is under constant high voltage. If output voltage changes from high to low, then the
alarm is triggered.
RECORD: Allows you to set the channel which will start recording once an alarm is activated.
(Choice of 1 to 4/1 to 8/ 1 to 16, multiple channels can be selected)
PTZ PRESET: Setting PTZ behavior after an alarm is triggered. Only preset point 1 can be
triggered (Choice of Channel 1 to 4/1 to 8/ 1 to 16, multiple channels can be selected).
ALARM ZOOM OUT: When the option is selected and one or more record channel is
selected, these record channels will touch off alarm zoom out.
60
ALARM OUT: Setting the triggered alarm output (ON or OFF options).
BUZZER: Setting the internal buzzer behavior after an alarm is triggered (ON or OFF options).
UPLOAD: Setting the option for sending information about an alarm to the center.
EMAIL: Setting the E-mail switch (ON or OFF options).
UPLOAD VIA FTP: upload the alarm picture via FTP.
Note 1: before setting alarm triggered record, please set up the record schedule
in Record Schedule.
Note 2: if you want to set alarm triggered PTZ, please ensure preset point is set
and proper PTZ channel number is selected (only preset 1 can be selected).
Note 3: if you want to set E-mail, please make sure that E-mail has been set
correctly.
This window allows the user to enable/disable alarm output on a daily basis. The table
represents days of the week from Sunday to Saturday located vertically, and hours of the day
from 0 to 24 on the horizontal line. Below the week grid you can see the legend for the color
encoding: White stands for the time when alarm is disabled, and Red denotes enabled alarm.
To mark the time cells, you can left click on them individually or click and drag to highlight the
required time span. If you choose your color code and click the day of the week, the complete
24 hour time span for that day will be highlighted in the selected color.
To save the changes click OK, to ignore the changes click CANCEL.
61
5.6.6 Device exception action
ALARM OUT: Checking this option will enable the Alarm Output when hard disk storage
capacity is full.
BUZZER: Checking this option will enable the internal buzzer when hard disk storage
capacity is full.
UPLOAD: If you have established a remote connection between the DVR and a PC via
the internet, and you check the UPLOAD checkbox, then on detecting hard
disk full, the DVR will send a relevant message to the IE applet.
E-MAIL: After you check this option, HDD full event will initiate an e-mail being sent
to the indicated addresses with a snapshot of that event as it was captured on
the camera (see Section 5.5.14 Email Settings for information on how to set
up the list of email addresses).
5.7 Maintenance
Information contained under this tab lets you view system and event logs, versions of software
and hardware and work with the HDD settings.
62
5.7.1 Log View
Clicking on the [>>] button will bring up the log window. In the Type field, you can choose the
features of a log you wish to see. The choice can be made among four options: All / Operation
/ Exception / Alarm. After that please indicate the time frame within which you’d like to
observe the log (Search Time field). The first value is start time; the second value is end time.
After that press the Search button and you will see the desired logs in the table below (it may
take several minutes to populate the list depending on the size and number of logs). The first
column will display the start time of an event in the YYYYMMDD HHMMSS format, and the
second column will list the description of the events.
If you have more log entries that cannot fit in one screen, you can move between screens by
using buttons Previous and Next located at the bottom of the window.
If you have already recorded the alarm events, you can double click it to play the file.
63
Note: The maximum number of entries currently supported is 3000.
When the database becomes full, the overwrite function kicks in and the
earliest entry will be replaced with the newest one.
5.7.2 Upgrade
To upgrade your software version, please use this function. The device supports software
updates from a USB drive and IE Remote Software. Before upgrading please make sure the
USB device is connected properly and the upgrade application has been copied into the USB
drive root directory (ie. F:\XXXXX.tar.gz). If no USB connection is found, a pop-up window
will appear, informing you that there is no available device.
Please follow the prompts to upgrade your software version. After completing the upgrade
process, you will need to restart the system. Pressing the Confirm button will restart the
system.
This option on the Maintenance Tab will help you accomplish this task.
64
pop-up window providing the following data for your consideration: Number, Type, Total
Memory, Available Memory and State.
In order to format your HDD please press Formatting button. You will see the progress in the
progress bar. To stop the formatting process, please press the Quit button. Depending on the
size of the HDD, the Format process can take quite a long time.
Upon completion of the formatting process you will be able to successfully use your HDD.
The four following fields provide only reference information and are not changeable.
65
User can export important parameters to a USB drive to save. And import the same parameters
to other DVRs.
5.7.6 Load Setting from USB
It is necessary to export parameter to a USB drive before importing any parameter from the
USB drive; otherwise, it will not be possible to successfully import the parameter.
5.7.7 Auto Maintain
Clicking on the [>>] button will bring up the auto maintain window. The options of “maintain
model” includes: Every Day, Every Week, Once and Disable. Users can set a specific time for
the DVR to restart. The system will restart automatically according to the parameter(s) chosen.
66
5.8 Save Settings
This is the last Tab in the Main Menu. It provides only four options as described below:
5.8.2 Exit
Exit the menu without saving any changes.
5.8.4 Logout
By using this option, you save all newly introduced changes and log out of the system. To be
able to operate the device you need to log in again with the user name and password.
67
6. Web Browser Operation
In Internet Explorer - Tools Menu - Internet Options settings under the Security tab, click on
the Custom Level button and select Enable (or Prompt) in the “Download unsigned ActiveX
controls” option and also Enable (or Prompt) in the “Initialize and script ActiveX controls not
marked as safe for scripting”.
68
Enter User Name and Password, check the “Automatically Open All Previews” option to be
able to view all cameras after the login. To reset entered values, press the Reset button and to
enter the system, press the Login button. The browser window will display the main remote
access screen.
The default user name and password of the administrator is “Admin” and “888888”. And the
default value of command port is “5050”.
69
1 The main and central position on the screen is taken by the camera view window. If you
selected “Automatically Open All Previews” in the previous window, all available
camera feeds will be displayed on this screen. You can bring up 1 camera view / 4
cameras / *8 cameras (depending on the model) /*16 cameras (depending on the model).
By default, the camera views will display the live feed (with an up to 2 seconds delay
from actual “live” events depending on the connection), though you can also access
recorded information from the Playback menu (see below).
2 In the bottom left corner of each individual camera view, you can see the indication of
the current status (previewing, idle). In the picture above, the camera is in preview mode
(see also item 4).
3 Right bottom corner of each individual channel is occupied by camera view tools:
: E-zoom. Click the button “ ” and then left-click and drag the cursor to select the
area to be magnified. Click the button “ ” again to exit zoom mode.
:Increase/decrease image contrast.
:Increase/decrease brightness.
:Start/stop voice monitoring. The icon will turn green when the recording process is on.
:Start/stop recording. The icon will turn green when the recording process is on.
Pressing this button will bring up a dialog window for local storage, which is the same
functionality as the Local Storage button in the Tools Menu. Please see 6.4.5 Local
Storage for more information.
:Takes a snapshot of the displayed image.
:Closes the window view. (You can open it again by clicking on the respective channel
in the channel list on the left (see item 5).
4 Current status of camera views with no video feed is indicated as idle (see also item 2).
5 Available Cameras list. Clicking on a channel (if this video feed is not open yet) will
display this camera view in the respective position on the screen. You can also Open All
or Close All camera views by pressing the buttons at the bottom of the camera list area.
6 Tools Bar
70
The Tools Bar allows you to adjust most needed settings for remote access to the DVR.
Detailed description of these options will follow below.
z Talkback: Allows you to talk to the operator at the location of the DVR
installation. Please see 6.4.2 Talkback for more information
z Playback: Use this feature to search and playback recorded files (from DVR as
well as saved on the local machine). Please see 6.4.3 Playback for more
information
z Device log: View and export logs. Please see 6.4.4 Log for more information
z Local Storage: Set parameters to store directly to local machine. Please see
6.4.5 Local Storage for more information.
The next three buttons work with the screen display mode. By using them, you can toggle the
single split view mode, and 4/8*/9*/16* split view mode (*depends on the model of your
DVR).
The data line below the Tools bar shows the name of the current user and gives a number of
functions:
In case of an interrupted or abnormal network connection, a poetic message will appear in the
top right corner of the main screen “No heartbeat of device, please check the network”. After
the network connection is recovered, the preview mode will be displayed automatically
6.4.1 Parameters
71
The first Menu item in the Tools Bar is Parameters. By clicking this button you will open the
Device Parameters dialog window with 7 tabs as shown below:
For the most part these settings are similar to those you can adjust on the DVR device, though
the menu layout and logic was slightly altered to better suit the PC configuration philosophy.
Please refer to Section 5.2 System Settings for configuration of the DVR parameters.
Detailed description of the functionalities offered by each of these tabs follows. If a field is
grayed, it means it is not changeable and is for your reference only. If the field is bluish-green,
it means that you can adjust the value of the field or choose it from a drop-down menu.
6.4.1.1 Server
The Server tab lets you adjust network settings. Most items here are self-explanatory and
correlate to the settings available on the actual DVR.
Device Configuration: You can enter the device name and choose the Signal
Standard (NTSC/PAL/SECAM)
72
Other values: Channel Count, Alarm Input, Device Serial
Number, Device Type, Hard Disk Count and Alarm Output
are not changeable and provide reference information related
to the actual DVR.
Manage Host: Checking this option activates the three fields: Host IP,
Manage Host Port and Register Interval in seconds.
To save and exit press the Confirm button, to exit without saving changes press Cancel.
You can also Restore Default values by pressing the first button in the last row, Save the
Parameters you just modified or Exit the window without saving.
6.4.1.2 Channel
This tab lets you adjust settings for each individual channel.
73
First of all you need to select the Channel whose settings you are going to review/change:
select the channel from the drop-down menu of the Channel Index option (a choice of
channels from 1 to 4 (9*) depending on the model).
Channel Name field lets you customize the name of the channel, ie “Front Door”, and
pressing the Font button brings up a dialog window allowing modification of the font size:
74
Activating the Motion Detect check box will initiate the motion detection feature of the
DVR for the selected camera. With the related buttons Setup and Action you can
respectively adjust the motion detection area and the alarm method.
Setup button:
Opens a live feed screen in which you can indicate cells for motion detection. Two
checkboxes – Display Area and Setup Area are mutually exclusive, where Display Area gives
you a clear view of the video feed, and Setup Area lets you indicate cells for motion detection.
You can also adjust sensitivity level on a three position slide scale (- / mid / +).
Action button:
75
Opens a pop-up window offering alarm method options when motion is detected: Sound
Alarm, Send to Center, and Email Notify.
If you check the Trigger Alarm Output option, another checkbox will become available:
Output 1.
To choose which channel will start recording on alarm, check the appropriate boxes on the list
under the Trigger Record option, offering all available channels.
When motion detection alarm is triggered, and the function of remote notification is activated
(i.e. check Send to Center box), you will see a message at the top right corner of the screen
containing such information as: “Device Alarm: Motion Detection, Channel 1”.
When you select both [alarm zoom out (tool bar—setting—video—motion handing—alarm
zoom out)] at DVR side and [send to center] at website. The corresponding channel will popup,
zoom out as a single show both at the DVR side and the website when alarm trigged.
If you check the Mosaic / Privacy Mask box, you can use the Setup button to access the
Setup Area screen with a number of check items: Display Area and Setup Area (the latter
allows you to select a privacy area).
76
To handle alarm options on Video Loss, you need to check the Video Loss Alarm box. To
modify relevant settings, press the Setup button. In the window below which will appear.
You can choose the Alarm Method for Video Loss: Sound Alarm, Send to Center, Email
Notify, and Trigger Alarm Output (checking the latter will make available another check
box: Output 1).
The Kind field works together with another option – Enable Sub-code, where if the latter
is activated, the Kind dropdown menu offers two options: Main Bit-rate and Sub
bit-stream. You can use this function to allow a lower network bit stream for slower
network connections or computers.
In the Signal Type field, you can choose two options from the dropdown menu: Video
Stream and Multiplex Stream
The dropdown menu for the Encode Mode field currently offers only one option: Advance
H.264
Video Bit-rate lets you choose the quality of video signal; the choice in the dropdown
menu is: Best, Good, Better, Normal, and Customize. If you choose Customize, in the
activated field to the right, you can enter the desired value in Kbps.
To further define the quality of the video signal, you can adjust the Frame Ratio value,
choosing among the dropdown options: FULL, and from 1 to 25)
Currently the system supports one kind of Resolution: CIF, as shown in the only option in
the Resolution field.
Brightness, Hue, Contrast and Saturation values can be adjusted on respective sliding
scales within the range from 1 to 16 (by default each of these values is set to 8).
Next part of the Channel Tab is a table for setting up the event-driven scheduled recording
77
(same function as the Record Schedule function on the Record Tab of the DVR device
Main Menu; cf. Section 5.3.2 Record Schedule). This is a weekly recording schedule for
various kinds of events Sunday through Saturday on a 24-hour basis. Week days are
represented vertically and the hour line runs horizontally from 0 to 24 hours. One cell
stands for one hour. Color-coded values denote the situations where the DVR will start
recording:
The dropdown menu Copy To offers options: All Channels and Channels 1 through
4/8*/16*(model dependent) individually. Pressing the Copy button will copy settings from
the current channel to All or specified channel(s).
The functions of Confirm and Cancel buttons are self-explanatory and refer to the
parameters of this tab. As with all other tabs in the Device Parameters window, you can also
Restore Default values by pressing the first button in the last row, Save the Parameters
you just modified or Exit the window without saving.
6.4.1.3 Serial
Next tab – Serial offers some important settings related to any serial devices connected to
the DVR, i.e. PTZ Cameras.
Channel: dropdown menu with options All Channels, and Channels 1 – 4 /*8/*16.
Baud Rate: dropdown menu with options 1200, 2400, 4800, 9600
78
Data Bit: dropdown menu with options ranging from 4 to 8
Flow control: currently inactive field with the default value None
Decoder Address: changeable field in which you can enter the PTZ address (default value:
1)
The dropdown menu Copy To offers options: All Channels, and Channels 1 through 4
individually. Pressing the Copy button will copy settings from current channel to All or
specified channels.
The functions of Confirm and Cancel buttons are self-explanatory and refer to the
parameters of this tab. As with all other tabs in the Device Parameters window, you can also
Restore Default values by pressing the first button in the last row, Save the Parameters
you just modified or Exit the window without saving.
6.4.1.4 Alarm
Alarm Type: dropdown menu with options Open and Close, referring to N.O. /N.C. Alarm
Exception: Exception type has three options: HDD full actions, offline, and IP collision. Click
setting to set the dispose.
79
Checkbox: Enable with the Alarm Schedule button next to it. Pressing this button will bring
up a schedule window similar to the one available in advanced Alarm settings of the DVR
device (see Section 5.6.4 Alarm Setting).
This window allows the user to enable/disable alarm output on a weekly basis. The table
represents days of the week from Sunday to Saturday located vertically and hours of the
day from 0 to 24 on the horizontal line. Color encoding has two options: White stands for
the time when alarm is disabled, and Red denotes enabled alarm.
To mark the time cells you can click on them individually or click and drag to highlight the
required time span.
To save the changes click OK, to ignore the changes click CANCEL.
Alarm Method subsection will help you setup system behavior in case of a triggered alarm.
You can choose among the following options by checking the respective boxes: Sound
Alarm, Send to Center, Email Notify and Trigger Alarm Output (checking the latter
option will make available another checkbox Output 1)
If Send to Center is checked, when alarms are triggered on the DVR, in the right top
corner of the main screen you will see an alarm notification with the alarm input number,
such as “Device alarm: IO alarm, IO input X”.
80
Trigger Record window lets you choose which channels will start recording after an alarm
is initiated. You can choose Channels 1 though 4/8* (depending on the model) individually,
or alternatively, use the All or None buttons located on the right.
PTZ Linkage subsection deals with PTZ control and offers two options:
Joint Channel: if a channel is connected to a PTZ camera, upon alarm, the PTZ camera
will be active. The dropdown menu offers a choice of All Channels or Channels 1
though 4 individually.
Checking the Present Point box will move associated PTZ camera to Preset Point,
making available a dropdown menu with preset points.
The dropdown menu Copy To offers options: All Alarm Input, and Alarm Input 1 through 4
individually. Pressing the Copy button will copy settings from current alarm to All or a
specified alarm input.
The functions of Confirm and Cancel buttons are self-explanatory and refer to the
parameters of this tab. As with all other tabs in the Device Parameters window, you can also
Restore Default values by pressing the first button in the last row, Save the Parameters
you just modified or Exit the window without saving.
6.4.1.5 User
This tab can help you adjust user account and authority settings.
81
In the leftmost field, you can see the list of available users.
Basic Information subsection provides such data as User Name, Binding IP, an option to
change the password (fields Password and Confirm Password), and the Binding MAC field.
By indicating Binding IP (static IP) or Binding MAC, you can restrict access to the DVR from
remote locations, i.e. the user will be allowed to connect to the DVR only from a fixed IP
address or a fixed PC, and not from any other IP or computer.
The major area of the rest of the screen is taken by the list of options which are
accessible/non-accessible by the selected user. Some options are changeable (i.e. may be
marked as accessible or given a restricted access), some are preset and cannot be changed
(Admin may restrict access to certain features by the user).
The list of rights includes Local and Remote sub-sections, meaning that these functions are
either on the local PC or on the remote DVR device. Both sub-sections contain identical items,
thus one and the same feature may be allowed on the DVR but inaccessible on the local
machine.
The list of features is as follows: System Setup, Clear Alarm, Shutdown, Local Playback,
Local Preview (Live Viewing), Local PTZ Control, Local Manual Record, Remote
Playback, Remote Preview (Live Viewing), Remote PTZ Control, and Remote Manual
Record.
Each item on the list is marked with an icon “ ”, showing which function is available for a
certain user.
Accredit checkbox: if it is inactive, the user has no right to change the settings as adjusted by
the Admin. The checkbox is active when the Admin is logged in, making it possible for him to
allow a certain function for a user (checkbox checked, i.e. the item is marked “ ”) or disable
this function (checkbox unchecked, i.e. the item is marked “ ”).
The functions of Confirm and Cancel buttons are self-explanatory and refer to the parameters
of this tab. As with all other tabs in the Device Parameters window, you can also Restore
Default values by pressing the first button in the last row, Save the Parameters you just
modified or Exit the window without saving.
6.4.1.6 Device
Settings available under this tab offer options for firmware upgrade and time synchronization.
82
Upgrade subsection offers options for upgrading the system. To find the file to upload, you
would need to search for it by pressing the Browse button, which will open a standard
Microsoft “Open File” window. After selecting the file, press the Start Upgrade button (you
can always stop this process by pressing Stop Upgrade).
The State field shows the current status of the upgrading function (Idle if no upgrading is
happening) and the Progress Bar which shows the current upgrading process.
Please indicate Server Address and Server Port, as well as User Name, Password and Email
Address of the Addresser (Sender).
The list of Addressees (Recipients) can be populated and altered with the help of the Add,
83
Modify and Delete buttons located on the right.
The functions of Confirm and Cancel buttons are self- explanatory and refer to the parameters
of this tab. As with all other tabs in the Device Parameters window, you can also Restore
Default values by pressing the first button in the last row, Save the Parameters you just
modified or Exit the window without saving.
6.4.1.7 State
In order to keep up to date with the changing values, you can check the Automatic Refresh
options and the data will be refreshed every 5 seconds or, alternatively, you can press the
Refresh button to view the latest information only when you need to see the data renewed.
As with all other tabs in the Device Parameters window, you can also Restore Default values
by pressing the first button in the last row, Save the Parameters you just modified or Exit the
window without saving.
6.4.2 Talk-back
This function allows you to have a live audio conversation with the operator
present at the location of the DVR installation. You can use the microphone
and loudspeakers of the PC to communicate, and it brings up no dialog windows. “ ”
indicates enable Talk-back.
6.4.3 Playback
The second option on the Tool Bar menu is Playback, which allows you to view recorded files
stored locally on the PC or remotely on the DVR’s HDD. When you press the Playback button,
84
a dialog / viewing window will appear:
The Playback window features two major parts – the left half is the screen with controls, and
the right half offers options for working with recorded files.
Query subsection
First of all you need to choose the Target from which you will be searching the recorded
files. Target field offers a dropdown menu: Remote Device (DVR) and Local host (PC).
Channel dropdown menu lets you choose among 4/*8/*16 (depending on the model)
channels.
You can select recorded files depending on their specific Kind from a dropdown menu: All
Records, Normal Record, Triggered by Alarm and Motion Detection.
You must also select the start time and end time of the recording you wish to see: use the two
dropdown menus Begin and End to indicate the relevant details by direct input. Format:
YYYY-MM-DD HH:MM:SS
After you enter all required details for the recorded files, please press the Query button. The
table below will be populated by the relevant entries (it may take a while depending on the
number of records and connection). The list features several columns:
85
No.: number of the files in order
In order to play a file, you need to select it by checking the box against it.
Alternatively you can select all files by pressing Select All button under the list of files, or
reverse the selection by pressing Reverse button.
Now you are able to play the selected files on the video screen to the left. Press Play button
under the list of files (description of the controls follows below).
To download the necessary files (if they are located on the remote device) select them on the
list and choose the destination in the Save To field by pressing the button. A standard
Windows Browse dialog will appear prompting you to choose the location.
Now you can press the Download button and the process of saving the selected files will
begin.
86
In the No. X progress bar, you will see the download process for the file currently being
saved (its number as it appears on the list will be shown to the left of the bar, and the time
elapsed will be displayed on the right). The Total progress bar shows the overall download
process if you are saving more than one file. To stop the download process, press the Stop
button.
After you press the Play button as described above, the selected files will be played in order
on the screen located in the left half of the window. Directly under the screen there is the
time line showing the elapsed time and the total time of the file.
Under the time line, there is the menu bar for controlling the playback of the selected files.
Play
Pause
Stop
Fast Rewind (options include – if going back from Fast Forward: 16X Æ 8X Æ
4X Æ 2X Æ Normal Æ 1/2 Æ 1/4 Æ 1/8 Æ 1/16 (this option, as well as the
previous one, cannot be looped, and to return to Normal speed step by step, you
will have to use Fast Forward button
Note: the playback speed is displayed under the time line (see below)
Decrease/increase contrast
Decrease/increase brightness
Mute sound
87
Under the control panel you can see the information on the currently played file:
This button on the Tools Menu will bring up the Device Log window. This function is similar
to the one accessible from the DVR under the Maintenance Tab of the Main Menu (see
Section 5.7.1 Log View).
You can select events (in various combinations) the logs of which you would like to view.
Please read the description of the available options below.
Channel: choose the channel for viewing a respective log (All or individual channels
1-4/*8/*16 depending on the model of your DVR).
88
If you choose to view All logs from all channels or one channel, all other options (Type,
Sub-Type, Begin Time, End Time) are not activated.
If you chose to view logs according to Time, the Begin Time and End Time fields will be
activated, though Type and Sub-Type will be inactive.
The time is expressed in the YYYY-MM-DD HH:MM:SS format. When selecting the time
frame for the desired logs, you can set up the start and end time either by highlighting the
necessary element and changing it from the keyboard, or by selecting the date and time from a
drop-down calendar.
There are four types available: All, Operation, Exception and Alarm.
If you select All types in the Type field, the Sub Type field will not be active.
If you select the Type as Operation, you activate 32 options for the Sub Type:
89
If you want to view your logs according to the type Exceptions, the Sub Type field will offer
these options:
Finally, if you select your type of query as Alarm, the 7 following options will be available in
the Sub Type field:
90
This query combines the two previous queries and along with the Begin and End Time options,
offers the whole gamut of the Type options as described in Section 6.4.4.3 Query Kind by
Type:
Each of the Operation, Exception and Alarm types also offer the same range of Sub Type
options as described in the section Query Kind by Type.
By pressing the Query button, you will submit your request specifications and will see the log
(it may take several minutes to populate the list depending on the number of entries and
connection).
Click Export to export logs in the HTML format. A standard Windows browse dialog will
appear prompting you to indicate the destination for saving the file.
91
6.4.5 Local Storage
Double-clicking left mouse key on windows in any kind of view will maximize the current
channel view to the full-screen. And double-clicking left mouse key again will backing out.
Single-clicking right mouse key on the window in any kind of view will maximize all the
current channels to the full-screen. And single-clicking right mouse key again will backing out.
See the table below for general description of the common features.
92
No. Name Description
Open/close auxiliaries.
Click to open and to close. Different
6 Auxiliary functions respond to different protocols. The auxiliaries
include light, wiper, power, etc. Please refer to PTZ
manual for details.
93
2. Click Set button .
3. Repeat steps 1 and 2 to add other presets till all
desired presets are complete.
4. Click Run button .
Clear sequence:
Click the button to clear sequence.
Setting track:
5. Click the button to start setting.
6. Move camera in the pattern you want it to run.
7. Click the button again to finish setup.
9 Track 8. Click the button to run track and click again to
stop running.
7. iPad support
This DVR device can transmit live feed from the CCTV cameras to your ipad(support iPad1
iPad 2 and iPad 3), so that you can have ‘on the go’ access to your surveillance system from
virtually anywhere. The iPad application needs to be downloaded directly from the iPad App
Store. Open the iPad App store and search for “KWeye+”, it’s a free application.
1) “KWeye+” installation
Open the iPad App store “ ”, search for “KWeye+”, it’s a free application. Choose “iPad
App” and then install the software “KWeye+”.
After installing “KWeye+”, it will appear an icon “ ” on the application software (shown
as below).
94
2) How to use “KWeye+”
①. Click the “KWeye+” icon to open the program. Click the “ ” button to add devices. On
the window of “Device Detail” to set up the DVR with “Name”, “Address”, “Port”, “User
ID”, “Password”, “Max Channel” and “Login Mode”. Click “ ” to save, and click
“ ” to previous.
②. There are two ways to view the live feed from the DVR on the screen: by IP address (or
DDNS) and by Auto ID.
a. By IP address (or DDNS)
After entering the Settings menu, the following fields will need to be completed:
95
First user needs to select the way to view the live feed from the DVR, by IP address or DDNS user
needs to set “Login Mode” as “Address”.
Name: Set name for DVR, and saves settings for future usage.
Address: The public IP address or dynamic domain name of the DVR.
Port: The mobile port of the DVR for remote access viewing via mobile phone, the default is
“7050”.
User ID: The user name set for entering the DVR system, the default is “Admin”.
Password: The password set for entering the DVR system, the default of administrator is
“888888”.
96
Max Channel: Select the max channels of the DVR will be connected.
Login Mode: To select the way to view the live feed from the DVR, including “Address” and
“ID”.
Click “ ” to save.
b. By ID
After entering the Settings menu, the following fields will need to be completed:
First user needs to select the way to view the live feed from the DVR, by ID user needs to set
“Login Mode” as “ID”.
Name: Set name for DVR, and saves settings for future usage.
DVR ID: The device ID number of the DVR. User can enter the menu
“Setting—Maintenance—Next Page”, and the interface includes “device ID”.
User ID: The user name set for entering the DVR system. Default is “Admin”.
97
Password: The password set for entering the DVR system. The default of administrator is
“888888”.
Max Channel: Select the max channels of the DVR will be connected.
Login Mode: To select the way to view the live feed from the DVR, including “Address” and
“ID”.
Click “ ” to save.
③. Move the green frame cursor to one of the multi-screen, and click to select one of the
channels in the Device list, it will connect immediately (see the following figures).
98
99
That is you can select 9 channels from different Device List (DVR) at most.
④. Double-click the screen, it will enlarge the selected channel, and back to multi-view if
double-click again.
While in multi-view mode, touch a channel on the screen and drag it to the channel position
directly.
⑤. On the interface of “Device List”, user can edit the parameters of one device or delete one
device. Click “ ” to enter edit mode, user can choose a device and click it to enter the
interface to adjust the parameters; click “ ” to enter delete mode, user can choose one
device and click it to remove from the list.
PTZ Control
Click these icons to switch the channel viewing mode among the quad-split
( ), six-split ( ) and nine-split ( ).
Recording local video by clicking and then click again to end. And the top right
corner of the recording channel has a normal recording video symbol “ ”.
Click “ ” to edit all the snapshot. User can save the snapshot on the iPad’s own file or
delete the snapshot he wanted to. There will be a symbol “ ” on the right bottom of the
100
selected picture, and click “ ” to save the picture on the iPad’s own file,
click “ ” to delete the selected pictures.
Touch one to see the picture. Click “ ” to save the picture on the iPad’s
own file. Click the button“ ” to the previous picture and click “ ” to the next picture.
Click “ ” to remove the picture user wanted to.
101
⑦. Click “ ” to manage all the local videos. User can playback any record on the list. Click
“ ” to enter into edit mode. If user wanted to save one record on the iPad’s own file,
please click the button “ ”. User can click “ ” to delete the records.
There will be a symbol “ ” on the right of the selected video. To delete one video, just
slice left in the name and the delete button will appear.
102
⑧. For PTZ operation, move the green frame cursor to one of the multi-screen which
connected to the PTZ camera, click the icon “ ” to enter into PTZ mode, and using the
following icons to control PTZ.
103
8. Mobile Phone Support
This DVR device can transmit live feed from the CCTV cameras to your mobile phone, so that
you can have ‘on the go’ access to your surveillance system from virtually anywhere. To view,
you must install a mobile operating system specific program into your mobile. The mobile
programs are located on the included CD, or downloaded via iTunes for the iPhone. In iTunes,
please search for “KWeye”(One View) or “KWeye+”(Quad view). Please see the instruction
manual for your mobile to install the program. Currently, there are a limited number of phones
that are supported: Windows CE Mobile, Nokia Symbian S60 3rd and 5th Edition OS, Google
Android(OS 1.6 or above & CPU 400M or above), BlackBerry(OS 5.0, OS 6.0 or OS 7.0, such
as 8900/ 9000/ 9100/ 9700/ 9800/ 9810/ 9900) and Apple iPhone(such as Iphone 3 / Iphone
3GS/ Iphone 4/ Iphone 4S/ Iphone 5).
Note:
1. Prior to using this feature, you should apply for an Internet connection service for
your mobile phone, such as 3G or 2.5G. Please contact your mobile service provider for
details.
2. You can only watch one live feed channel at a time with your mobile phone. Split
mode and playback of recorded files is not available at the moment.
3. You can watch four live feed channels at a time with Google Android and Iphone
Mobile.
Find and execute program KWeye and click the Setting button to setup the IP address for your
DVR.
In the ensuing screen, input the user name (Admin), password, and IP address for your DVR
(Server).
Input the value for the Port: default 7050 and choose the channel for streaming data from the
dropdown menu.
104
The main window of the Mobile Phone application offers the
choice of channels, Connect and Settings buttons.
To connect to the system and start watching the live feed from
your CCTV cameras, click on the Connect button.
Snapshot
Please see a sample installation process shown below (The N95 will be taken as an example to
introduce installation):
105
(1) Copy “KWeye_JH_3rd_1222.sisx” to your mobile from the installation CD;
(2) Open file management on your mobile and find “KWeye_JH_3rd_1222.sisx” you have
copied;
(3) Select “Options” and a dialog will displayed which indicates “Install Kweye?” You
should choose “Yes” to continue the following steps; after you choose “Yes”, a dialog
will appear as picture below, select “continue”
(4) After selecting “Continue” on last picture above, the software will start install. After
installation, there will be a icon named “KWeye” in application interface.
106
(5) Select “KWeye” to execute KWeye and the program window will appear on the screen.
Select icon and press button “ENTER” to enter setting interface.
107
Selection of channels. If your system supports
8-channels, to switch between channel buttons 1-4 and
5-8 please use functional button (see below)
Next Group. Toggling between two available 4-channel views: 1-4 and 5-8
* Available only for programs supporting 8-camera views
Exit KWeye.
In order to start working with the CCTV feed on your Symbian mobile phone, you will have to
configure the program by entering the preferred network access point, IP address of the DVR,
mobile phone port, username, and password.
Click the icon to enter the setup window.
108
Nokia 6121 S60 3rd_FP1
Nokia 6210 Navigator S60 3rd_FP2
Nokia 6220 S60 3rd_FP2
Nokia 6290 S60 3rd_FP1
Nokia 6710 Navigator S60 3rd_FP2
Nokia 6720 Classic S60 3rd_FP2
Nokia E51 S60 3rd_FP1
Nokia E55 S60 3rd_FP2
Nokia E60 S60 3rd_INIT
Nokia E61 S60 3rd_INIT
Nokia E61i S60 3rd_INIT
Nokia E62 S60 3rd_INIT
Nokia E63 S60 3rd_FP1
Nokia E65 S60 3rd_INIT
Nokia E66 S60 3rd_FP1
Nokia E70 S60 3rd_INIT
Nokia E71 S60 3rd_FP1
Nokia E75 S60 3rd_FP2
Nokia E90 S60 3rd_FP1
Nokia N71 S60 3rd_INIT
Nokia N73 S60 3rd_INIT
Nokia N75 S60 3rd_INIT
Nokia N76 S60 3rd_FP1
Nokia N77 S60 3rd_INIT
Nokia N78 S60 3rd_FP2
Nokia N79 S60 3rd_FP2
Nokia N80 S60 3rd_INIT
Nokia N81 S60 3rd_FP1
Nokia N81 8GB S60 3rd_FP1
Nokia N82 S60 3rd_FP1
Nokia N85 S60 3rd_FP2
Nokia N86 8MP S60 3rd_FP2
Nokia N91 S60 3rd_INIT
Nokia N92 S60 3rd_INIT
Nokia N93 S60 3rd_INIT
Nokia N93i S60 3rd_INIT
Nokia N95 S60 3rd_FP1
Nokia N95 8GB S60 3rd_FP1
Nokia N96 S60 3rd_FP2
Samsung I7110 S60 3rd_FP2
Samsung INNOV8 S60 3rd_FP2
Samsung SGH-G810 S60 3rd_FP1
Samsung SGH-i400 S60 3rd_FP1
Samsung SGH-i450 S60 3rd_FP1
Samsung SGH-i520 S60 3rd_FP1
Samsung SGH-i550 S60 3rd_FP1
Samsung SGH-i560 S60 3rd_FP1
Samsung SGH-L870 S60 3rd_FP2
109
8.4 Apple iPhone
The Apple iPhone application, like all iPhone applications, needs to be downloaded directly
from the iPhone App Store. Open iPhone APP store, search for “KWeye” (only one channel
view) or “KWeye+” (quad view), they are free applications.
I. For “KWeye+”
Open the iPhone App store “ ”, touch “ ” and search for “KWeye+”. It will be a free
application. Download and install onto iPhone as per iPhone installation procedures.
Please locate the icon KWeye+ and click on it to open the application. Set up the device
(DVR) by “ ” as follows. Click the option “ ” to enter the window of
“Device List”. On the window of “Device List”, click “ ” to add devices; click “ ” to
enter edit mode, user can choose a device and click it to enter the interface to adjust the
parameters; click “ ” to enter delete mode, user can choose one device and click it to remove
from the list. On the window of device detail to set up the DVR with “Name”, “Address”,
“port”, “User ID” , “Password” and “Max Channel”. Click “ ” to save, and click “ ” to
return to the interface of “Device List”.
110
Name: Set name for DVR, and saves settings for future usage.
Address: The public IP address or dynamic domain name of the DVR.
Port: The mobile port of the DVR for remote access viewing via mobile phone, the default is
“7050”.
User ID: The user name set for entering the DVR system. (Admin by default)
Password: The password set for entering the DVR system. (888888 by default)
Max Channel: Select the max channels of the DVR will be connected.
Click “ ” to the window of “Device List”, and click “ ” to the main window. On the
main window, click play button “ ”, a piece of message “Select channel in the playback
111
window” will appear, and click the button “ ” to enter the window of “Device List” to select
the channel to view.
- Play button: press this to connect to DVR and view
live feed.
112
Fig 1
Fig 2
5. Click on “Application Loader” to enter into its interface. In this screen you have two
options to select from. Select “Add/Remove Applications” (shown as follows).
113
6. You should now see something like what you see below. From this screen, click “Browse”
(shown as follows).
7. Once you click “Browse” you will see a file search screen like the one below. Go to and
locate where you saved the application files. Make sure you saved both the “.alx” file
and “.cod” file in the same folder. After finding the “KWeye.alx” file for the application,
highlight it and click “open”.
114
8. You will now return to the Application Loader screen. From here you should see “KWeye”
now listed with Install under the Action column (shown as follows)
9. Click “NEXT” to install this software and click “Finish” to start installation.
115
10. You can remove the program “KWEye” as the following method. To enter into Application
Loader screen, on “Device application selection” you can select the application that you
want to clear from your device. When the option “Action” is “Remove”, it means the
program will be clear from your device.
11. Click “Next” and the screen will show as follows. Click “Finish” to confirm and the
application “KWeye” can be removed from your device.
116
2) System explanations
KWeye phone port has the following capabilities and functions: live video surveillance, channel
switch, full screen display, PTZ control, including zoon/focus/iris, image capture, save as
favorite and exit function.
① System main interface
After the installation, press “KWeye” icon in the application, see the below picture.
117
Name: Set name for Device;
Address: DVR IP address
Port: Mobile Port [7050 by default]
User ID: Login User Name〖Admin〗
Password: Password [888888 by default]
Network Type: WIFI or 3G
Login: Click this button to login live interface.
Cancel: Click this button to exit system.
Device list: Click this button to show device list and choose the one you want to connect.
118
④ Connect to DVR
To connect to the server, move the icon to “Connect” and it will be highlighted. Press the enter
button on your mobile to connect to the server.
In the interface the user can switch the channel, PTZ control, image capture and full screen
display, please see the below picture:
See below for more details:
Connect: Connect or disconnect to your DVR;
Full Screen: Display images in full screen mode;
Capture: Capture image;
Setting: Click this button to turn back configure interface;
About: Click to display information about KWeye
Channel Switch: Switch between channels
Control PTZ camera direction
-Zoom out zoom in;
-Set focus
- Set iris
119
3) Familiar questions and their answers
1:Why can’t it connect to the server?
A: Check that the server, port, user name, password settings are correct.
B: Make sure the mobile phone is connected to the Internet.
2:Why can’t I control the PTZ after entering into the main interface?
A: Check if the channel is a PTZ camera and properly set up.
B: The PTZ might take a few moments to load; please be patient.
120
When the application has finished installing, the phone will display the following screen.
121
②. There are two ways to view the live feed from the DVR on the screen: by IP address (or
DDNS) and by ID.
a. By IP address (or DDNS)
After entering the Settings menu, the following fields will need to be completed:
First user needs to select the way to view the live feed from the DVR, by IP address or DDNS user
need to set “Login Mode” as “Address”.
DVR Title: Saves settings for future usage.
Server: The public IP address or dynamic domain name of the DVR.
Port: The server port of the DVR for remote access viewing via mobile phone, the default
is “7050”.
User Name: The user name set for entering the DVR system. Default is “Admin”.
Password: The password set for entering the DVR system. Default is “888888”.
Max Channel: Select the max channels of the DVR will be connected.
Login Mode: To select the way to view the live feed from the DVR, including “Address”
and “ID”.
Click “ ” to save.
b. By ID
After entering the Settings menu, the following fields will need to be completed:
122
First user needs to select the way to view the live feed from the DVR, by ID user need to set “Login
Mode” as “ID”.
DVR Title: Saves settings for future usage.
DVR ID: The device ID number of the DVR. User can enter the menu “Setting—
Maintenance—Next Page”, and the interface includes “device ID”.
User Name: The user name set for entering the DVR system. Default is “Admin”.
Password: The password set for entering the DVR system. Default is “888888”.
Max Channel: Select the max channels of the DVR will be connected.
Login Mode: To select the way to view the live feed from the DVR, including “Address”
and “ID”.
Click “ ” to save.
③. Move the red frame cursor to one of the quad screen, and click to select one of the channels
in the Device list, it will connect immediately.
That is you can select 4 channels from different Device List (DVR).
④. Double-click the screen, it will enlarge the selected channel, and back to quad view if
double-click again.
⑤. On the interface of “Device List”, user can edit the parameters of one device, click “ ” to
the interface of “Settings” to adjust the parameters. Click “ ” to save. Click “ ” to
remove the information of the current device.
123
⑥. For PTZ operation, move the red frame cursor to one of the quad screen which connected to
the PTZ camera, using figure touch on the screen or the following icons to control PTZ.
PTZ lens controls: zoom in/zoom out, focus+/ focus-, iris+/ iris-.
Other icons as below:
124
1.2 Open your “ES File Explore” in android phone and find the [KWeye_ceshi] File in your
android phone memory or SD card. Click [KWeye.apk] to install software.
125
Open the main interface, see the below picture:
Click the icon to enter into setting interface. For the first time using or need to modify the
parameters, press [setting] button to access to the parameters setting.
126
Address: The public IP address or Domain name of DVR.
Port: The server port which is set on DVR [default: 7050].
Device Name: Set device name for DVR
User name: The user name which is set on DVR
Password: The user password which is set on DVR
After the setting press [Back] and back to the front interface. After the setting, press “connect”
button on the main interface and then it will connect the server. In this interface it can also
switch the channel, full screen magnify, PTZ control, focus, phone capture and full screen
display.
: It can control the PTZ move up, down, left and right.
127
2:After enter into the main interface, why the user cannot control the PTZ?
a: Check if the channel has the PTZ camera setting.
b: if network bandwidth is insufficient then video refresh slowly for PTZ control. Please wait a
moment for video refresh.
Troubleshooting
This basic troubleshooting guide will help you identify general malfunctions and offer
steps for quick resolution of such.
If the failure or malfunction can't be solved by following these steps, please contact a qualified
technician.
Problem Solution
The host device fails to - Make sure the power switch on the device is turned on, and
start after being connected that there is sufficient power.
to the power supply - Check that the start-up procedure is working.
128
Check to make sure the video input, DVR, and monitor
The image on the monitor systems are compatible, i.e. all NTSC or PAL. Alternatively,
appears in black and white at night time, most video appears black/white. If you find
rather than color some incompatibility or inconsistency, please set the
monitor system option to the automatic identification state.
The image distorts, -Ensure that the VGA connecting line is properly grounded.
flickers and has color casts -Be aware that a high working ambient temperature or
when viewed on the radiation from the host computer may cause interference
computer display with the normal operation of the VGA display.
The displayed date and Please login as Administrator and adjust Date and Time
time in the lower-left settings in the System Tab of the Main Menu.
corner are not correct
129
Appendix 1 Estimating HDD Capacity
The system currently supports 1TB HDDs. That may seem like a lot of space, though with
constant non-stop recording these gigabytes will be used up fairly quickly.
The task of estimating how many hours/minutes of recording time may be left on 500 MB of
free space may be a little tricky as well. That could seem irrelevant when you have the whole
disc space available, but as you realize you would like to view events from several weeks or
months ago, it quickly becomes relevant. The following formulas can help you feel more
confident when calculating the remaining disc space. Please also keep in mind that the utilized
disk space may depend on the video signal format, the video quality, the number of frames per
second, and the bit rate.
z Timed Recording:
Step 1: Calculating maximum capacity of hard disk space for an hour of recording from
a given channel.
Assuming that Sch is the disk space needed for recording of an hour of live feed at the
bit rate of B (Kbit/s), the formula for calculating HDD space for an hour of recording
would be:
Sch = (B*3600) / (8*1024) = B * 0.439453125 MB
Step 2: Calculating the amount of HDD space (St) needed for recording of T hours.
From previous calculation Sch is the disk space needed for 1 hour of recording. Then:
St = T * Sch
Step 3: To calculate how much of total disk space you’d need to record from as many
channels as you need, you will have to add up all the channels you will be using:
Stotal = Sch1 + Sch2 + … + Sn
For your convenience, you can use the approximate table below of HDD space needed
for recording an hour of video feed from one camera depending on video format,
resolution, frame rate and bit rate. For instance, on a 4 Channel DVR, at 768kbps bit
rate, an hour recording for 4 channels is 1.29GB, or a 500GB HDD can probably record
for about 15 days (assuming some space is needed for system storage on the HDD).
z Alarm Recording
Less disk space will be used if you set up your device to record only selected events,
such as only when an alarm is triggered. If the rate of triggered alarms is α%, then the
hard disk space needed in alarm recording (Sa) will be calculated according to the
formula:
Sa = Stotal * α%
130
Appendix 2 Compatibility Table for HDDs
Please find below the list of tested Hard Disk Drives, found to be compatible with the DVR. If
you want to use a HDD not found in this list, please test it for compatibility before use.
Brand name Model Number Size (GB) Drive
Seagate ST3320410SV 320GB SATA
Seagate ST3500418AS S7200.12 500GB SATA
Seagate ST3500320SV SV35.3 500GB SATA
Seagate ST32000542AS 2TB SATA
Seagate ST1000VX000 1TB SATA
Seagate ST2000VX000 2TB SATA
Seagate ST2000DM001 2TB SATA
Seagate ST2000DL003 2TB SATA
Seagate ST3500312CS 500GB SATA
WD WD10EURX 1TB SATA
WD WD5000AAKX 500GB SATA
WD WD5000AAKS 500GB SATA
WD WD7500AAKS 750GB SATA
WD WD10EACS-OOD6B0 1TB SATA
WD WD20EADS 2TB SATA
Please find below the list of tested portable USB DVD recorders found to be compatible with
the DVR. If for backing up your data from the DVR, you wish to use a DVD recorder not
found on this list, please test it for compatibility.
• Pioneer
131
Appendix 5 How to Use Auto ID-"Plug n play" Quick
Guide
The Auto ID is used for connecting the DVR to an Internet browser interface. For detailed
instructions, refer to the following instructions.
1. Regarding use of the router to browse the Internet, first you should have the transmit codex
of the router’s port already mapped. From the toolbar, click “Setting->Net->Next
Page->Next Page”, then set up the option “UPnP” to “ON”. And the router will
automatically map the port.
2. The ID number of each product is set in the factory. From the toolbar, click “Setup”—
“Maintenance”—“Next page”, and the DVR ID number will appear at the bottom of the
screen (as in the following illustration):
132
“http://www.ipremoteview.cn” in the address field of the Internet browser. Then enter the
DVR ID number into the “Product ID” field, as shown in the following picture.
Note: If after following the preceding instructions the login page does not work or the Auto ID
function fails, try the following steps to add the website to the zone:
4. After the connection has been established, the Web Application Management (see the
following figure) will appear. Fill in the right user name (default “Admin”), password
(default “888888”) and command port(default “5050”); click [LOGIN] to login the system.
133
Appendix 6 How to Use RTSP
This DVR device support RTSP protocol, user can view one live feed channel with the remote
access to DVR through “VLC Media Player”.
First please download “VLC Media Player” from “http://www.videoLan.org/VLC”, and then
install the VLC media player on your PC.
134
According to the following method to view live video of the DVR remotely.
1. Run VLC media player,
3. Input the right path such as “rtsp://ip address of the DVR/ user name& password / channel/
type” in the address field “Please enter a network URL”, then click the button “Play”. User
name is the same as entering the DVR system, default is Admin. Password is the same as
entering the DVR system, default is 888888 of administrator. Channel is the channel will be
connected remotely. Type is code flow type, include main code and sub code.
For example, the ip address of the DVR is “192.168.1.120”, the user name is “Admin”, the
password is “888888”, and to view channel 2. When connecting with main code, input
“rtsp://192.168.1.120/Admin&888888/ch2”. When connecting with sub code, input
“rtsp://192.168.1.120/Admin&888888/ch2/sub”.
135
4. Click the button “Play” and a window of “RTSP authentication” will appear. Input correct
“User name” and “Password”. Then click the button “Ok” to enter the live view.
Note: User only can watch one channel view through the VLC media player, and can’t
playback through it.
136