Jumo Dtrans P20 Delta: Differential Pressure Transmitter

JUMO GmbH & Co. KG JUMO Instrument Co. Ltd. JUMO Process Control, Inc.
Delivery address: Mackenrodtstraße 14 JUMO House 6733 Myers Road

36039 Fulda, Germany Temple Bank, Riverway East Syracuse, NY 13057, USA
Postal address: 36035 Fulda, Germany Harlow, Essex CM 20 2DY, UK Phone: +1 315 437 5866
Phone: +49 661 6003-0 Phone: +44 1279 63 55 33 Fax: +1 315 437 5860
Fax: +49 661 6003-607 Fax: +44 1279 62 50 29 Email: info.us@jumo.net
Email: mail@jumo.net Email: sales@jumo.co.uk Internet: www.jumousa.com
Internet: www.jumo.net Internet: www.jumo.co.uk
Data Sheet 403022 Page 1/11
JUMO dTRANS p20 DELTA

Differential pressure transmitter
Brief description
The device with HART® interface combines maximum precision with simple operation. It is used
to measure the system pressure of gases, steams, and liquids. The integrated LCD display
shows measured values and device data.
The version with explosion protection "Ex ia (intrinsically safe)" allows the device to be installed
up to zone 0.
The housing and sensors are manufactured from high-grade stainless steel. Diaphragm seals Type 403022/0-0-1-...
can also be connected for specific process technology applications (see data sheets 409772 to
409784).
The device is programmable and therefore readily adaptable to a variety of different measure-
ment tasks. An easy-to-use setup program is available as an accessory to enable operation via
the interfaces. A rotary knob makes manual operation on-site very convenient and quick.
The pressure transmitter with 4 to 20 mA and HART® protocol was evaluated with regard to
functional safety and is certified by TÜV Nord according to DIN EN 61508/-1/-2, edition 2.0.
These measuring devices are suitable for monitoring process level and process pressure up to
SIL2. Further details can be found in the Safety Manual. Type 403022/0-0-2-...
For the "Ex d" explosion protection version, see data sheet 403023.
For the relative and absolute pressure version, see data sheet 403025 and 403026.
Type 403022/0-0-3-...
Block diagram Special features

• Stainless steel case
®
HART interface • SIL certified (TÜV Nord)
Differential pressure
setup program
®
HART Communicator • HART® interface
• Explosion protection Ex ia (gas and dust)
according to ATEX and EAC
• Linearity 0.07 %
JUMO interface • Simple operation with rotary knob
Type 403022
setup program
• Setup program
Rotary knob • LCD display with bar graph
To operate: turn and press
• Display scaling with a choice of measur-
Display ing units
2-line plus bar graph • Display of sensor temperature
• Display of minimum and maximum pres-
sures
• Current-generator function
Analog output
• Characteristic line and display also ad-
4 to 20 mA
Voltage supply
linear or square root justable for flow measurement
Approvals/approval marks (see "Technical data")
V4.00/EN/00519466 40302200T10Z001K000
Phone: +49 661 6003-0 Phone: +44 1279 63 55 33 Fax: +1 315 437 5860
Technical data
General Information
Reference conditions DIN EN 60770 and DIN EN 61298
Ambient temperature 22 °C ±5 K
Air pressure 1000 hPa (±25 hPa)
Voltage supply DC 24 V
Burden 50 Ω
Sensor system Silicon sensor with stainless steel separating diaphragm
Pressure transfer medium
For measuring system filling medium 1 Silicon oil
For measuring system filling medium 2 Halogenized filling oil
Admissible load changes > 10 million
Position
Mounting position Any
Calibration position Device upright, process connection at the bottom
Zero offset depending on position ≤ 1 mbar
A zero offset is possible on-site or via setup
Displaya LCD, two-line with bar graph
Alignment Display unit rotatable in 90° steps
Housing rotatable ±160°
Size Display 22 × 35 mm, font size 7 mm/5-digits
Color Black
Portrayable measuring units
Input pressure inH2O, inHg, ftH2O, mmH2O, mmHg, psi, bar, mbar, kg/cm2, kPa, torr, MPa, mH2O
Measured value % or scaled with freely adjustable measuring unit
Output current mA
Sensor temperature °C, °F
Additional display data Minimum pressure, maximum pressure, error, overrange, underrange, operating hours
Operation
On-site With rotary knob and LCD
Setup program Via interface
Interface
Standard JUMO interfaceb
For output 410 (4 to 20 mA with HART®) JUMO interfaceb and HART® interface
a
optional; SIL version only available with display
b The JUMO interface may not be used in a potentially explosive area! In such a case the device can be operated via the rotary knob or the
HART® interface.
Input
Nominal pressure
Nominal measuring range -10 to +10 mbar DPa -1 to +1 bar DP 0 to 1 bar DP -1 to +6 bar DP -1 to +100 bar DP
Nominal pressure (bar) PN2 PN210 PN210, optionally PN420
a
Without SIL
V4.00/EN/00519466 40302200T10Z001K000
Phone: +49 661 6003-0 Phone: +44 1279 63 55 33 Fax: +1 315 437 5860
Output
Analog output
For output 405 (4 to 20 mA) 4 to 20 mA, two-wire
For output 410 4 to 20 mA, two-wire with HART® version 7
(4 to 20 mA with HART®) (optionally with HART® version 5, extra code 932, always with SIL version)
Jump response time T60 ≤ 190 ms without attenuation
Attenuation Adjustable 0 to 100 s
Burden
For output 405 (4 to 20 mA) Burden ≤ (UB-12 V) ÷ 0.022 A
For output 410 Burden ≤ (UB-12 V) ÷ 0.022 A; additional: min. 250 Ω, max. 1100 Ω
(4 to 20 mA with HART®)
Voltage supply
For version
Explosion protection 0 (none) DC 12 to 36 V
Explosion protection 1 (ATEX Ex ia) DC 12 to 28 V
The voltage supply must be intrinsically safe and must not exceed the following maximum values:
Ui ≤ DC 28 V
Ii ≤ 115 mA
Pi ≤ 750 mW
Ci = 6 nF
Li = 105 µH
V4.00/EN/00519466 40302200T10Z001K000
Phone: +49 661 6003-0 Phone: +44 1279 63 55 33 Fax: +1 315 437 5860
Mechanical features
Process connection
Materials
Membranes
For process connection 20 Stainless steel 316 L
(stainless steel)
For process connection 82 HASTELLOY® C276, material-no. 2.4819
(HASTELLOY®)
For process connection 80 (tantalum) Tantalum
Flange Stainless steel 316
Seal PTFE
Housing
Materials
For housing 1 (short, stainless steel) Stainless steel 1.4404
For housing 2 (long, stainless steel) Stainless steel 1.4404, VMQ
For housing 3 (precision casting) Stainless steel 1.4408
For material lid 20 (stainless steel) Precision casting 1.4408, seal FPM
For material lid 85 PA, seal FPM
(plastic)
For electrical connection 36 Brass nickel-plated
(round plug M12 × 1)
For electrical connection 82 PA
(cable fitting, plastic)
For electrical connection 93 Brass nickel-plated
(cable fitting, metal)
For operation 0 -
(without control knob)
For operation 1 (with control knob) PA
Explosion protection
For
Explosion protection 0 (without) The device is not approved for use in an Ex-area.
Explosion protection 1 (ATEX Ex ia) EC type examination certificate SEV 09 ATEX 0138 X
II 1G Ex ia IIC T4 Ga
II 1D Ex ia IIIC T105 °C Da
Weight
Type 403022/0-0-1 (housing short) Approximately 3.0 kg
Type 403022/0-0-2 (housing long) Approx. 3.3 kg
Type 403022/0-0-3 (housing precision cast- Approximately 4.0 kg
ing)
For extra code 694 (increased nominal pres- The weight of the device increases by approximately 3.8 kg.
sure)
V4.00/EN/00519466 40302200T10Z001K000
Phone: +49 661 6003-0 Phone: +44 1279 63 55 33 Fax: +1 315 437 5860
Environmental influences
Admissible temperatures
Operation Version Temperature Maximum medi- Ambient Increased
class um temperature temperaturea ambient
temperature
(extra code 681)a, b,
c
Standard 110 °C -40 to +85 °C -50 to +85 °C

II 1G Ex ia T4 100 °C -40 to +60 °C -50 to +60 °C
II 1D Ex ia T105 °C 100 °C -40 to +60 °C -50 to +60 °C
Storage -40 to +85 °C
Admissible humidity
Operation 100 % including condensation on the device outer case
Storage 90 % without condensation
Admissible mechanical load
Vibration strength 2 g, 10 to 500 Hz according to DIN EN 60770-3
Shock resistance 15 g for 6 ms according to IEC 60068-2-29
Electromagnetic compatibility According to EN 61326
Interference emission Class Bd
Interference immunity Industry
Protection type
For version
Explosion protection 0 (without) IP66/67 according to DIN EN 60529
Explosion protection 1 (ATEX Ex ia) IP66 according to DIN EN 60529
a
Under -20 °C limited function: stationary use, increased danger of cable break, display without function; under -30 °C operation of the device
not possible.
b In the range from -40 to -50 °C the device must be permanently in operation. Furthermore, the lid with the device inspection glass must addi-
tionally be protected against mechanical impact and shock effects. Please contact JUMO for further details.
c
Without SIL
d
The product is suitable for industrial use as well as for households and small businesses.
V4.00/EN/00519466 40302200T10Z001K000
Phone: +49 661 6003-0 Phone: +44 1279 63 55 33 Fax: +1 315 437 5860
Accuracy
Including non-linearity, hysteresis, non-repeatability, zero point and final value deviation (corresponds to measurement deviations according to
IEC 61298-2), calibrated at vertical installation position with the process connection at the bottom
Differential pressure
Nominal measuring range -10 to +10 mbar DPa -1 to +1 bar DP 0 to 1 bar DP -1 to +6 bar DP -1 to +100 bar DP
Default measuring range 0 to 10 mbar 0 to 1 bar 0 bar to 6 bar 0 bar to 100 bar
Smallest MSPb 1 mbarc 5 mbarc 0.350 bar 2.5 bar
d
Turndown ratio (r) r ≤ 20 r ≤ 400 r ≤ 200 r ≤ 20 r ≤ 40
Non-linearity for reference condi- 0.1 % 0.07 % 0.07 %
tions for r ≤ 2 for r ≤ 10 for r ≤ 5
r × 0.05 % r × 0.007 % r × 0.007 % r × 0.014 % r × 0.014 %
for 2 ≤ r ≤ 20 for 10 ≤ r ≤ 400 for 10 ≤ r ≤ 400 for 5 ≤ r ≤ 20 for 5 ≤ r ≤ 40
Accuracy in % 0.2 % 0.1 % 0.1 %
of the set MSP for r ≤ 2 for r ≤ 10 for r ≤ 5
at 20 °C r × 0.1 % r × 0.01 % r × 0.01 % r × 0.02 % r × 0.02 %
Accuracy in % 0.5 % 0.2 % 0.2 %
Range: 20 to 85 °C (only to 60 °C)
r × 0.25 % r × 0.02 % r × 0.02 % r × 0.04 % r × 0.04 %
(only to 60 °C)
Accuracy in % 1.0 % 0.6 % 0.6 %
Range: -40 to +20 °C r × 0.5 % r × 0.06 % r × 0.06 % r × 0.12 % r × 0.12 %
Accuracy in % 2.0 % 2.0 % 2.0 %
Range: 60 to 85 °C r × 1.0 %
for 2 ≤ r ≤ 20
Influence of the static pressure P ≤1% ≤ P × 0.0005 % ≤ P × 0.0003 % ≤ P × 0.0025 % ≤ P × 0.001 %
(bar) in %
from the nominal measuring range
Long-term stability in % ≤ 0.6 %/year ≤ 0.1 %/year ≤ 0.2 %/year
as of the nominal measuring range
a
Without SIL
b MSP = measuring span
c For the calibration certificate from JUMO the smallest MSP is 10 mbar. MSPs smaller than 10 mbar can be adjusted by the user.
d
r = span of the nominal measuring range ÷ adjusted measuring span
Approvals/approval marks
Approval mark Test facility Certificates/certification num- Inspection basis Valid for
bers
ATEX Electrosuisse SEV 09 ATEX 0138 X EN 60079-0 403022/x-1-...
EN 60079-11
EN 60079-26
EAC RU RU C-DE.ME92.B.00440 - Extra code 226
SIL TÜV Nord (German Techni- No. SEBS-A. DIN EN 61508/-1/-2 Basic type extension 2 and 3
cal Inspection Agency) 140944/16 V1.0
V4.00/EN/00519466 40302200T10Z001K000
Phone: +49 661 6003-0 Phone: +44 1279 63 55 33 Fax: +1 315 437 5860
Dimensions
Type 403022/0-0-1 Type 403022/0-0-2
(short, stainless steel, with M12 connection) (long, stainless steel, with cable fitting)
86.5 104
138
63.5
ø73
127
51
191
1/4-18 NPT
7/16-20 UNF
41.3
54 94
87
A M20 × 1.5 cable fitting
Type 403022/0-0-3 For extra code 694

(precision casting, with cable fitting) (increased nominal pressure PN420)
109
145
66
A A
ø73
119
57
182
A M20 × 1.5 cable fitting A M20 × 1.5 cable fitting

B M8 for mounting
V4.00/EN/00519466 40302200T10Z001K000
Phone: +49 661 6003-0 Phone: +44 1279 63 55 33 Fax: +1 315 437 5860
Connection diagram
The connection diagram in the data sheet provides preliminary information about the connection options. For the electrical connection, only use
the installation instructions or the operating manual. The knowledge and the correct technical compliance with the safety information and warnings
contained in these documents are mandatory for mounting, electrical connection, and startup as well as for safety during operation.
Connection Terminal assignment

82 (plastic), 36
93 (metal) Round plug M12 × 1
Cable gland
Voltage supply 1 L+ 1 L+
DC 12 to 36 V for none Ex version 2 L- 3 L-
DC 12 to 28 V for Ex version
Output 1 L+ 1 L+
4 to 20 mA, two-wire 2 L- 3 L-
Impressed current 4 to 20 mA
in voltage supply
Current output test connection TEST +
Inherent resistance of ammeter ≤ 10 Ω TEST -
HART® test connection HART +
Burden must be present! HART -
Functional ground 3 4
Cable fitting
Round plug M12 × 1
2 1
3 4
V4.00/EN/00519466 40302200T10Z001K000
Phone: +49 661 6003-0 Phone: +44 1279 63 55 33 Fax: +1 315 437 5860
Order details
(1) Basic type
403022 JUMO dTRANS p20 DELTA – differential pressure transmitter
(2) Basic type extension
0 None
2 SILa
3 SIL, customer-specifica
9 Special version
(3) Explosion protection
0 None
1 ATEX Ex iab
(4) Housing
1 Short, stainless steel, with M12 connectionc
2 Long, stainless steel, with cable fitting
3 Precision casting, with cable fitting
(5) Electrical connection
36 Round plug M12 × 1
82 Plastic cable fitting
93 Metal cable fitting
(6) Cover material
20 CrNi (stainless steel)
85 Plastic
(7) Display
0 None
1 With display (LCD)
(8) Operation
0 None
1 With control knob
(9) Input – nominal measuring range
530 -10 to +10 mbar DPd, e, f
532 0 to 1 bar DP
531 -1 to +1 bar DPe
533 -1 to +6 bar DP
534 -1 to +100 bar DP
(10) Output
405 4 to 20 mA, two-wire, without SIL
410 4 to 20 mA, two-wire with HART® protocol
(11) Process connection
511 2× pressure connection 1/4-18 NPT according to DIN EN 837
998 Diaphragm seal process connection
(12) Process connection material
20 CrNi (stainless steel)
80 Tantalum
82 NiMo
(13) Measuring system, filling medium
01 Silicon oil
02 Halogenized oil for oxygen application
(14) Extra codes
000 None
100 Customer-specific factory settingg
V4.00/EN/00519466 40302200T10Z001K000
Phone: +49 661 6003-0 Phone: +44 1279 63 55 33 Fax: +1 315 437 5860
226 With GOST/EAC approvalh

624 Oil and grease free
633 Mounting brackets for 2" tube
634 With TAG number
635 With NACE manufacturer's declarationi
681 Expanded admissible ambient temperaturef
694 Increased nominal pressure PN 420 bar
932 With HART® version 5, always with SIL version (basic type extension 2 and 3)
a SIL version always with LCD display (display 1), connection 4 to 20 mA (output 410) and HART® version 5 (extra code 932)
b
ATEX Ex ia does not apply in connection with a cable fitting made out of plastic (process connection material 82) and the connection 4 to 20 mA
(output 405).
c The short housing is only available with a round plug M12 × 1 (electrical connection 36).
d
This input is only available with a process connection made out of stainless steel (process connection 20).
e
The inputs are not available with an increased nominal pressure (extra code 694).
f
Without SIL
g
Please specify the setting you want in plain text. For default setting see “Accuracy” section in the data sheet.
h Upon request
i Only with NiMo (process connection material 82); not for pressure ranges -10 to +10 mbar and -1 to +1 bar
(1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) (12) (13) (14)
Order code / - - - - - - - - - - - /
Order example 403022 / 0 - 0 - 2 - 82 - 20 - 1 - 1 - 532 - 405 - 511 - 20 - 1 / 000
Accessories
Article Part no.
a
PC interface with USB/TTL converter 00456352
HART® modem USBb 00443447
4-pole terminal box, straight, M12 × 1, with 2 m PVC cable 00404585
4-pole terminal box, angled, M12 × 1, with 2 m PVC cable 00409334
5-pole terminal box, straight, M12 × 1, without cable 00419130
5-pole terminal box, angled, M12 × 1, without cable 00419133
SET oval flange 1/2“ NPT/accessories set 7/16-20UNF 00543775
Mounting kit, set includes 7/16-20UNF screws 00543777
Article Part no.

Manifolds 409706
Pressure separator with milk pipe fitting DIN 11851 409772
Pressure separator with clamp connection 409774
Pressure separator with DRD flange or VARIVENT® connection 409776
Pressure separator with ISS connection or SMS connection or RJT connection and slotted ring nut 409778
Diaphragm chemical seals 4MDV-10 409780
Pressure separator with male thread ISO 228/1 or ANSI B1.201 409782
Pressure separator with flange connection EN 1092-1 with sealing lip Form B1 409784
Pressure separator with flange connection to ANSI B 16.5 with sealing lip Form RF 409786
Ex-i Power supply/input isolating amplifier 707530
a
The PC interface cable is the connection between the JUMO interface of the differential pressure transmitter and the USB interface of a PC.
b The HART® modem is the connection between the HART® interface of the differential pressure transmitter and the USB interface of a PC.
V4.00/EN/00519466 40302200T10Z001K000
Phone: +49 661 6003-0 Phone: +44 1279 63 55 33 Fax: +1 315 437 5860
Software
Description Part no.
JUMO setup dTRANS p20 series 00537577
JUMO dTRANS p20 series, DD (device description) Upon request

JUMO dTRANS p20 series, DTM (device type manager) Upon request
V4.00/EN/00519466 40302200T10Z001K000

Jumo Dtrans P20 Delta: Differential Pressure Transmitter

Uploaded by

Copyright:

Available Formats

Jumo Dtrans P20 Delta: Differential Pressure Transmitter

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Jumo Dtrans P20 Delta: Differential Pressure Transmitter

Uploaded by

Copyright:

Available Formats

JUMO GmbH & Co. KG JUMO Instrument Co. Ltd. JUMO Process Control, Inc.

Delivery address: Mackenrodtstraße 14 JUMO House 6733 Myers Road

Data Sheet 403022 Page 1/11

JUMO dTRANS p20 DELTA

Block diagram Special features

Approvals/approval marks (see "Technical data")

Data Sheet 403022 Page 2/11

Data Sheet 403022 Page 3/11

Data Sheet 403022 Page 4/11

Data Sheet 403022 Page 5/11

Standard 110 °C -40 to +85 °C -50 to +85 °C

Data Sheet 403022 Page 6/11

Data Sheet 403022 Page 7/11

A M20 × 1.5 cable fitting

Type 403022/0-0-3 For extra code 694

A M20 × 1.5 cable fitting A M20 × 1.5 cable fitting

Data Sheet 403022 Page 8/11

Connection Terminal assignment

Round plug M12 × 1

Data Sheet 403022 Page 9/11

Data Sheet 403022 Page 10/11

226 With GOST/EAC approvalh

Article Part no.

Data Sheet 403022 Page 11/11

JUMO dTRANS p20 series, DD (device description) Upon request

You might also like