201.TK109 GPS Watch Tracker User Manual
201.TK109 GPS Watch Tracker User Manual
201.TK109 GPS Watch Tracker User Manual
Table of Contents
1
Chapter I Preface……………………………………………………..4
I.General……………………………………………………………...4
II.Notices……………………………………………………………..4
1. Appearance…………………………………………………………..5
2. Product Features…………………………………………………….5
3. Product Specification……………………………………………….6
(1).Technical Specifications…………………………………………6
(2).Others……………………………………………………………7
I.Accessories…………………………………………………………..8
2. Interface Definition………………………………………………...9
1. Location Inquiry………………………………………………….12
2
3. Bi-directional Call Function……………………………………...13
5. SOS Function……………………………………………………...15
6. Monitoring Function……………………………………………...15
Notices…………………………………………………………………..22
Chapter I Preface
I. General
3
field. It is a typical design combing communication products and GPS
services.
II. Notices
1. Please read this user’s manual carefully and always use correct
operation methods to prevent any possible errors.
2. This user’s manual is for reference only. If some contents and
operation steps are inconsistent with those for the actual product,
the latter will prevail.
3. The defaulted password of this product is 0000.
4
1 Appearance
2 Product Features
5
● In emergency, press the SOS button to have an accurate positioning
3 Product Specifications
(1). Technical Specifications
GSM module GSM 850/900/1800/1900 MHz Quad frequency
GPS sensitivity -163dBm
GPS center L1, 1575.42MHz
frequency
GPS positioning 5-25m
accuracy
GSM positioning 100-500m
accuracy
Speed accuracy 0.1 m/s
Time accuracy Synchronous with GPS
GPS Datum WGS-84
Hot start < 1s
Warm start < 38s
Max. altitude 18000m
Max. speed 515m/s
Gravitational ﹤4g
acceleration
(2). Others
Operating temperature -20---65℃
Humidity 5%---95%
Dimensions 64.5mm×45.5mm×17.5 mm (main unit)
Voltage Rechargeable 450mAh battery
Power supply DC5V
Standby time >48h
Buttons SOS button for emergency aid; Call 1, Call 2,
Switch on / off buttons, interface switch
button
6
2. USB data cable
3. Charger
4. Headset cable (optional)
5 Battery
II. Appearance and Interface
1. Appearance and Buttons
Five buttons are equipped with this watch, the upper left button serves
for switch-on and hold-on, the bottom left button serves interface
middle right button for emergency aid (SOS button) and the bottom
2. Interface Definition
GSM signal strength is indicated on the upper left corner of the main
interface as showed in picture 2:
7
Bottom left button is for interface switch as showed in picture 3:
Please use up the battery and discharge it for 2-3 times and then
charge the battery for at least 12 hours for initial use, in order to keep
the quality of the battery.
The normal charging time of this product is 4-5 hours.
Put the battery into the inside of the terminal and connect the charger
to 100V/220V AC power supply to charge the battery. Then the power
indicator on the upper right corner of the terminal screen will keep
strolling as showed in picture 3-1:
( picture 3-1 )
When the battery is fully charged, the power indicator will stop
strolling; if the battery is charged on switch-off mode, the following
picture 3-2 indicates the charging is finished:
8
( picture 3-2 )
Notes:
Open the back cover, then you will see the place where the SIM card is
placed. Then push the SIM card into the slot until it comes into its proper
position completely and consolidate it with the dome sheet nearby.
The type of the SIM card is GSM card (the SIM card of China Mobile
is recommended).
Ensure sufficient money is within the SIM card in order to pay the
communication fee.
Prepare a SIM card for mobile phone (the SIM card of China Mobile
is recommended), make sure that the card has opened such functions
9
of Caller ID and sending and receiving SMS. If service platform real-
time tracking is in need, then GPRS function should be open.
1. Location Inquiry
By the same means, send the command 987 plus password to the
terminal, then the terminal will return a piece of website message. The
guardian may inquire the location information of the ward attached with
10
local map through this website message.
In the same way, send command 666 plus password to the terminal, then
the terminal will return a piece of detailed latitude and longitude message.
Step 1: Log onto the platform (Please contact with the service provider to
get the platform address).
Step 2: Click the terminal of the ward, then the location of the ward will
be displayed on the map.
11
3. Bi-directional Call Function
Send the command in form of SMS to the terminal via mobile phone.
After the setup is successful, the mobile phone will receive the
“&710&successful setting&&” response message from the terminal.
Notes: After the setup is successful, press the upper right button for a
while, then the terminal will automatically dial the first phone number.
Press the bottom right button, then the terminal will automatically dial the
second phone number.
While making phone calls, the user could press upper or bottom right
button to adjust receiver volume.
5. SOS Function
12
SOS button for emergency aid interface
SOS SMS format: IMEI number: SOS (information about latitude and
longitude or base station)
Example: 356823031017473:SOS(11354.6397,E,2232.6283,N)
or 356823031017473:SOS(26280E77)
6. Monitoring Function
The guardian may send SMS 555 plus password to the terminal of the
ward, then the ward terminal will automatically call back to the mobile
phone of the guardian and the guardian may hear the sound of the
surroundings within 10m around the ward.
13
Command format: # command number 730# Sampling interval # Pieces
of uploads # User password ##
Example: 730#20#4#0000##
Notes: The parameter “20” indicates getting one point every 20s; after
getting points accumulatively for 4 times, upload one piece of positioning
information with the upload interval as 20*4=80s. The user may change
this parameter as the case may be.
Send the SMS “#770# User new password # User old password ##” by
mobile phone to the terminal number, after successful sending, the mobile
phone with such setup will receive one piece of ‘&770&successful
setting&&’ response information or ‘&770&PASSWORD ER&&’ if the
password is wrong, as shown in the following picture:
14
9. Set User name Command
Example: #801#13900139000#0000##
Notes: After executing this command, the user name of the terminal on
GPRS mode is required to be set up according to actual demand. After the
setup is successful, the terminal will send reply with ‘&801&successful
setting&&’ or ‘&801&PASSWORD ER&&’ if the password is wrong.
Create the SMS “802#APN letters or digits, 4-20 bits # Log user name
letters or digits 4-20 bits in # Log password letter or digits 4-20 bits in #
terminal password 4 bits ##” and send it to the terminal; after executing
this command, the terminal will automatically restart and connect to
GPRS with APN set.
This command is used to set GPRS center server address, which could
be fixed IP number, like IP1, IP2, IP3, IP4……as well as domain
15
name with the length less than 64. After the setup is successful, the
module will send a reply with ‘&803&successful setting&&’ or
‘&803&PASSWORD ER&&’ if the password is wrong.
Example: #803#222.73.173.204#7003#0000##
Example: #803#gps.chinaradio.hk#9876#0000##
If the terminal of the ward has a very low power and needs to be powered
off, the terminal of the ward will automatically upload one piece of low-
voltage alarming command to the monitoring center number.
SMS Format: IMEI Number: low power; please charge the battery in time
(information about latitude and longitude or base station)
16
command 8960000E08 and the time will change into Beijing time.
The guardian could get the center spot of a fence through Google map or
single inquiry.
Example: #751#500#5#22.5442N#113.91E#0000##
After the setup is successful, the mobile phone will receive a piece of
‘&751&succeful setting&&’. Then, each time when the ward leaves this
area, the terminal will send the alarming information of being out of the
fence to the center number.
Example: #752#0000##
Return:#open:1#lat:11456.209400#lng:2233.470100#distance:500#time:5
#status:2
lat:11456.209400, latitude;
17
distance: 500; fence radius;
time: 5 sampling interval;
status: 2, terminal has obtained valid satellite data, fence works normally;
status: 1, fence open, but there are no valid satellite data have been
received;
Example: #760#0000##
After the terminal receiving this command, all fence settings will be
cancelled.
Advice: Do not set GSM fence and GPS fence at the same time.
Notices
18
the service area, even if you are a registered user.
5. This device supports the dual positioning mode of GPS and
GSM/GPRS.
6. Please use this device in a legal area, any illegal consequence will be
borne by the user.
Notes: due to the high sensitivity of the GPS module adopted by this
product, it is normal to be drifting with weak GPS signal.
19