Fiat Linea T Jet Emotion Service Manual
Fiat Linea T Jet Emotion Service Manual
Fiat Linea T Jet Emotion Service Manual
Dear Customer,
Thank you for selecting Fiat and congratulations on your choice of a Fiat Linea.
We have written this handbook to help you get to know all the features of your car and use it in the best possible way.
You should read it right through before taking the road for the first time.
You will find information, tips and important warnings regarding the driving of your car to help you derive the maximum from the
technological features of your Fiat.
You are recommended to read carefully the warnings and indications, marked with the respective symbols:
personal safety;
environmental protection.
The enclosed Warranty Booklet lists the services that Fiat offers to its Customers:
❒ the Warranty Certificate with terms and conditions for maintaining its validity
❒ the range of additional services available to Fiat Customers.
Best regards and happy motoring!
MUST BE READ!
REFUELLING
petrol engines: only refuel with unleaded petrol with octane rating (RON) not less than 95 conforming to the
K
European specification EN 228.
Diesel engines: only refuel with diesel fuel conforming to the European specification EN590.
The use of other products or mixtures may damage the engine beyond repair and consequently cause lapse of
warranty in relation to the damage caused.
ENGINE STARTING
petrol engines: make sure that the handbrake is engaged; set the gearshift lever to neutral; fully depress the clutch
without pressing the accelerator, then turn the ignition key to AVVand release it as soon as the engine has started.
Diesel engines: make sure that the handbrake is engaged; set the gearshift lever to neutral; fully depress the clutch
without pressing the accelerator, then turn the ignition key to MAR and wait for the warning lights Y and m
to go off; turn the ignition key to AVVand release it as soon as the engine has started.
or other flammable material: fire risk .
ELECTRICAL ACCESSORIES
If, after buying the car, you decide to add electrical accessories (with the risk of gradually draining the battery),
쇵
visit a Fiat Dealership. They can calculate the overall electrical requirement and check that the car’s electric
system can support the required load.
CODE card
Keep it in a safe place, non in the car. Make sure you have the electronic code with you at all times.
SCHEDULED SERVICING
Correct maintenance of the car is essential for ensuring it stays in tip-top condition and safeguards its safety
features, its environmental friendliness and low running costs for a long time to come.
AND CONTROLS
DASHBOARD
DASHBOARD AND CONTROLS
DASHBOARD........................................................................ 5 EXTERNAL LIGHTS ............................................................ 66
SYMBOLS ............................................................................... 6 WINDOW WASHING ....................................................... 68
DEVICES
SAFETY
CONTROLS........................................................................... 75
OF THE CAR
ALARM ................................................................................... 11
IGNITION DEVICE .............................................................. 13 FUEL CUT-OFF SWITCH .................................................. 77
INTERIOR FITTINGS........................................................... 78
INSTRUMENT PANEL ........................................................ 14
LIGHTS AND
MESSAGES
DOORS .................................................................................. 82
WARNING
INSTRUMENTS ..................................................................... 16
POWER WINDOWS........................................................... 83
DIGITAL DISPLAY ............................................................... 18
BOOT ...................................................................................... 86
MULTIFUNCTION DISPLAY ............................................ 23
EMERGENCY
BONNET................................................................................. 88
IN AN
MANUAL CLIMATE CONTROL SYSTEM .................... 53 AT THE FILLING STATION ............................................. 101
AUTOMATIC CLIMATE CONTROL SYSTEM ............ 59 PROTECTING THE ENVIRONMENT............................. 102
4
001-031 LINEA 1ed GB 4-09-2008 14:55 Pagina 5
DASHBOARD
AND CONTROLS
DASHBOARD
The presence and position of the controls, the instruments and the indicators may vary according to the versions.
DEVICES
SAFETY
CORRECT USE
OF THE CAR
LIGHTS AND
MESSAGES
WARNING
EMERGENCY
IN AN
SPECIFICATIONS MAINTENANCE
TECHNICAL CAR
F0R0001m
fig. 1
1. Adjustable side air vents - 2. Fixed side air vents - 3. Left stalk: external lights control - 4. Instrument panel -
5. Right stalk: windscreen wiper controls, trip computer - 6. Controls on dashboard - 7. Adjustable central air vents - 8. Fixed up-
INDEX
per air vent - 9. Front airbag - passenger side - 10. Oddment compartment - 11. Sound system (where provided) - 12. HVAC
controls - 13. Ignition device - 14. Front airbag - driver’s side - 15. Steering wheel adjustment lever - 16. Control panel: fog
lights/rear fog light/headlight position adjustment/digital display/multifunctional display.
5
001-031 LINEA 1ed GB 4-09-2008 14:55 Pagina 6
AND CONTROLS
DASHBOARD
SYMBOLS THE FIAT CODE SYSTEM
Special coloured labels have been attached This is an electrical engine locking system
near or actually on some of the compo- which increases protection from at-
nents of your car. These labels bear sym- tempted theft of the car. It is automatically
bols that remind you of the precautions activated when the ignition key is ex-
DEVICES
SAFETY
EMERGENCY
IN AN
SPECIFICATIONS MAINTENANCE
TECHNICAL CAR
INDEX
6
001-031 LINEA 1ed GB 4-09-2008 14:55 Pagina 7
Warning light Y
AND CONTROLS
OPERATION In this case, turn the key to STOP and
DASHBOARD
then back to MAR; try with the other coming on when driving
Each time the car is started turning the ig- keys provided if the problem persists.
nition key to MAR, the Fiat CODE sys- Contact a Fiat Dealership if you still can- ❒ If the warning light Y turns on, this
tem control unit sends a recognition code not start the engine. means that the system is running a self-
to the engine control unit to deactivate test (for example for a voltage drop).
the inhibitor. IMPORTANT Each key has its own code
DEVICES
SAFETY
which must be stored by the system ECU. ❒ If the warning light Y stays on, con-
The code is sent only if the Fiat CODE Contact a Fiat Dealership to have new tact a Fiat Dealership.
system control unit has recognised the keys (up to eight) stored.
code transmitted from the key.
CORRECT USE
OF THE CAR
Each time the ignition key is turned to
STOP, the Fiat CODE system deactivates The electronic components
the functions of the engine electronic con- inside the key may be dam-
trol unit. aged if the key is submitted to
LIGHTS AND
MESSAGES
sharp knocks.
WARNING
If the code has not been recognised cor-
rectly, the warning light Y turns on ac-
companied by the related message on the
display (see section “Warning lights and
EMERGENCY
messages”).
IN AN
SPECIFICATIONS MAINTENANCE
TECHNICAL
INDEX CAR
7
001-031 LINEA 1ed GB 4-09-2008 14:55 Pagina 8
AND CONTROLS
DASHBOARD
THE KEYS
F0R0003m F0R0004m
A the electronic code; fig. 2 fig. 3
Make sure you have the electronic code The metal insert A is retractable and it op-
A-fig. 2 with you at all times. erates:
B.
SPECIFICATIONS MAINTENANCE
8
001-031 LINEA 1ed GB 4-09-2008 14:55 Pagina 9
AND CONTROLS
WARNING
DASHBOARD
and the tailgate.
Only press button B with the
key away from your body, Button Á is used for locking the doors and
specifically from your eyes and from the tailgate.
objects which could get damaged (e.g. Button R (present in some versions on-
your clothes). Do not leave the key
DEVICES
SAFETY
ly) is used for remote opening of the tail-
unattended to avoid the button from gate.
being accidentally pressed while it is
being handled, e.g. by a child. The passenger’s compartment lights will
CORRECT USE
come on for a preset time when the doors
OF THE CAR
F0R0006m
fig. 5
are unlocked.
LED indications on the driver’s
door fig. 5
LIGHTS AND
MESSAGES
WARNING
When locking the doors, led A switches
on for about 3 seconds and than starts
flashing (deterrence function).
If one or more doors or the tailgate are
EMERGENCY
not closed correctly when the doors are
IN AN
locked, the led and direction indicators
start flashing quickly. The operation will
not be completed.
SPECIFICATIONS MAINTENANCE
TECHNICAL
INDEX CAR
9
001-031 LINEA 1ed GB 4-09-2008 14:55 Pagina 10
AND CONTROLS
DASHBOARD Request for additional remote
Used batteries are harmful to
controls the environment. They should
The system may recognise up to 8 remote be disposed of as specified by
controls. Should a new remote control be law in the special containers
necessary, contact a Fiat Dealership, tak- provided, or take them to a Fiat Deal-
ing with you the CODE card, a personal ership, which will deal with their dis-
DEVICES
SAFETY
F0R0007m
fig. 6
Battery replacement:
❒ press button A and open the metal in-
sert B;
❒ turn the screw C to : using a fine bit
EMERGENCY
IN AN
screwdriver;
❒ take out the battery case D and replace
the battery E making sure that the bias
SPECIFICATIONS MAINTENANCE
is correct;
CAR
10
001-031 LINEA 1ed GB 4-09-2008 14:55 Pagina 11
ALARM
AND CONTROLS
HEADLIGHT WASHER
DASHBOARD
(where provided) fig. 7
The metal insert of the key A is fixed. The car alarm system is available at Lin-
eaccessori Fiat.
The key operates:
❒ the ignition switch;
DEVICES
SAFETY
❒ the door locks;
❒ the fuel filler lock (where provided).
CORRECT USE
OF THE CAR
F0R0008m
fig. 7
LIGHTS AND
MESSAGES
WARNING
EMERGENCY
IN AN
SPECIFICATIONS MAINTENANCE
TECHNICAL
INDEX CAR
11
001-031 LINEA 1ed GB 4-09-2008 14:55 Pagina 12
AND CONTROLS
DASHBOARD The main functions that can be activated with the keys (with or without remote control) are the following:
Type Unlocking Locking the doors Unlocking the Windows down Windows up
the doors from the outside tailgate (where provided) (where provided)
Key without remote control Turn key anticlockwise Turn key clockwise
– – –
DEVICES
SAFETY
Key with remote control Press briefly Ë Briefly press Á Briefly press R Hold pressed Ë Hold pressed button Á
(for longer than 2 (for longer than
seconds) seconds)
Direction indicators blinks twice blinks once blinks twice blinks twice blinks once
LIGHTS AND
MESSAGES
WARNING
deterrent blinking
IMPORTANT The windows will be opened when the doors are unlocked; the windows will be closed when the doors are
SPECIFICATIONS MAINTENANCE
locked.
TECHNICAL CAR
INDEX
12
001-031 LINEA 1ed GB 4-09-2008 14:55 Pagina 13
IGNITION
AND CONTROLS
STEERING COLUMN LOCK
DASHBOARD
DEVICE Engaging
The key can be turned to 3 different po- When the key is at STOP, remove the
sitions fig. 8: key and turn the steering wheel until it
DEVICES
locks.
SAFETY
❒ STOP: engine off, key extractable,
steering locked. Some electrical devices
(e.g. sound system, central door lock- Disengaging
ing system, etc.) may work.
CORRECT USE
Rock the steering wheel slightly as you
OF THE CAR
F0R0009m
fig. 8
❒ MAR: driving position. All electrical de- turn the ignition key to MAR.
vices may work.
WARNING
❒ AVV: engine starting (unstable posi- Always remove the key when
LIGHTS AND
tion). WARNING
MESSAGES
WARNING
you leave your car to pre-
The ignition switch is fitted with an elec- vent someone from accidentally op- Never extract the key while
tronic safety system that, in the event the erating the controls. Remember to the vehicle is moving. The
engine is not started, turns back the igni- apply the handbrake. Engage first steering wheel would be locked as
gear if the car is parked uphill or re- soon as the steering wheel is turned.
EMERGENCY
tion key to STOP before repeating the
This also applies to when the car is
IN AN
starting operation. verse if the car is parked downhill.
Never leave children unattended in towed.
the car.
SPECIFICATIONS MAINTENANCE
WARNING
CAR
If the ignition device is tam- WARNING
pered with (e.g.: attempted It is absolutely forbidden to
theft), have it checked over by a Fiat carry out whatever after-
Dealership as soon as possible. market operation involving steering
TECHNICAL
system or steering column modifica-
tions (e.g.: installation of anti-theft
device) that could badly affect per-
formance and safety, cause the lapse
of warranty and also result in non-
INDEX
compliance of the car with homolo-
gation requirements.
13
001-031 LINEA 1ed GB 4-09-2008 14:55 Pagina 14
AND CONTROLS
DASHBOARD
INSTRUMENT PANEL
Versions with digital display
A Speedometer (speed indicator)
B Fuel level gauge with reserve warning
DEVICES
SAFETY
light
C Engine coolant temperature gauge and
excessive temperature warning light
CORRECT USE
OF THE CAR
D Rev counter
E Digital display
LIGHTS AND
MESSAGES
WARNING
fig. 9 F0R0010m
Versions with multifunction display
EMERGENCY
IN AN
E Multifunction display
INDEX
fig. 10 F0R0011m
14
001-031 LINEA 1ed GB 4-09-2008 14:55 Pagina 15
AND CONTROLS
DASHBOARD
Versions with reconfigurable
multifunction display
A Speedometer (speed indicator)
DEVICES
SAFETY
B Fuel level gauge with reserve warning
light
C Engine coolant temperature gauge and
CORRECT USE
OF THE CAR
excessive temperature warning light
D Rev counter
E Reconfigurable multifunction display
LIGHTS AND
MESSAGES
WARNING
EMERGENCY
fig. 11 F0R0215m
IN AN
SPECIFICATIONS MAINTENANCE
TECHNICAL
INDEX CAR
15
001-031 LINEA 1ed GB 4-09-2008 14:55 Pagina 16
AND CONTROLS
DASHBOARD
INSTRUMENTS
Instrument background colour and type
may vary according to the version.
DEVICES
SAFETY
CORRECT USE
OF THE CAR
F0R0012m F0R0013m
fig. 12 fig. 13
er.
IN AN
charge.
INDEX
16
001-031 LINEA 1ed GB 4-09-2008 14:55 Pagina 17
AND CONTROLS
Warning light B may light up (and a mes-
DASHBOARD
sage on the multifunctional display may ap-
pear in certain versions) to indicate that
the coolant fluid temperature is too high;
in this case, stop the engine and contact
a Fiat Dealership.
DEVICES
SAFETY
If the needle reaches the red
CORRECT USE
OF THE CAR
F0R0014m F0R0015m
fig. 14 fig. 15
area, stop the engine imme-
diately and contact a Fiat
FUEL LEVEL GAUGE fig. 14 ENGINE COOLANT Dealership.
This shows the amount of fuel left in the TEMPERATURE GAUGE fig. 15
LIGHTS AND
MESSAGES
WARNING
fuel tank. This shows the temperature of the engine
E empty tank(see “At the filling station”). coolant fluid and begins working when the
fluid temperature exceeds approx. 50°C.
F full tank.
Under normal conditions, the needle
EMERGENCY
The reserve warning light A turns on to should hover around the middle of the
IN AN
indicate that approximately 7 litres of fu- scale according to the working conditions.
el are left in the tank.
C Low engine coolant temperature.
Do not travel with the tank nearly empty:
SPECIFICATIONS MAINTENANCE
lack of fuel supply could damage the catal- H High engine coolant temperature.
CAR
yser.
IMPORTANT The needle will point to E
and warning light A will blink to indicate a
TECHNICAL
fault in the system. Go to a Fiat Dealer-
ship to have the system checked.
INDEX
17
001-031 LINEA 1ed GB 4-09-2008 14:55 Pagina 18
AND CONTROLS
DASHBOARD
DIGITAL DISPLAY
F0R0016m F0R0017m
fig. 16 fig. 17
nition key removed and front doors
closed).
CONTROL BUTTONS fig. 17 Note Buttons + and – activate different
C Odometer (distance covered in kilo- functions according to the following situ-
metres or miles) and TRIP data. + To scroll the displayed menu and the ations:
LIGHTS AND
MESSAGES
WARNING
confirm the required menu op- panel brightness, sound system, and auto-
IN AN
18
001-031 LINEA 1ed GB 4-09-2008 14:55 Pagina 19
AND CONTROLS
SETUP MENU fig. 18 Selecting a menu option Hold button MENU ESC pressed
DASHBOARD
The menu comprises a series of functions – press briefly button MENU ESC to se- – to quit the set up menu if you are in the
arranged in a cycle which can be selected lect the menu option to set; menu;
through buttons + and – to access the dif-
ferent select operations and settings (set- – press buttons + and – (by single press- – to quit the displayed menu if you are set-
up) given in the following paragraphs. es) to select the new setting; ting an option;
DEVICES
SAFETY
– press briefly button MENU ESC to – to save only the settings stored yet (and
The setup menu can be activated by press- confirmed by pressing button MENU
ing briefly button MENU ESC. store the new setting and to go back to
the previously selected menu option. ESC).
Single presses on buttons + and – will
CORRECT USE
The setup menu displaying is timed; when
OF THE CAR
scroll the setup menu options. Selecting “Set Clock”
quitting the menu due to timing expiry, on-
Handling modes differ with each other ac- – briefly press button MENU ESC to se- ly settings stored yet by the user (and con-
cording to the characteristic of the option lect the first value to change (hours); firmed by pressing briefly button MENU
selected. ESC).
– press buttons + and – (by single press-
LIGHTS AND
MESSAGES
WARNING
es) to select the new setting;
– briefly press button MENU ESC to
store the new setting and to go to the
next setup menu option (minutes);
EMERGENCY
IN AN
– after setting the values with the same
procedure, the system will go back to the
menu option previously selected.
SPECIFICATIONS MAINTENANCE
TECHNICAL
INDEX CAR
19
001-031 LINEA 1ed GB 4-09-2008 14:55 Pagina 20
AND CONTROLS
DASHBOARD
Briefly press button MENU ESC to start browsing
from the standard screen. Press + or – to browse with-
in the menu.
Note Only the short menu may be accessed for rea-
sons of safety while the car is moving (“SPEEd” setting).
DEVICES
SAFETY
+
–
LIGHTS AND
MESSAGES
WARNING
+
EMERGENCY
IN AN
+
–
SPECIFICATIONS MAINTENANCE
CAR
+
TECHNICAL
– +
F0R2003g
–
INDEX
fig. 18
20
001-031 LINEA 1ed GB 4-09-2008 14:55 Pagina 21
AND CONTROLS
Setting the speed limit (SPEEd) – briefly press button MENU ESC to go Adjusting the buzzer volume
DASHBOARD
back to the menu screen or press the but- (bUZZ)
This function may be used to set the car ton for long to go back to the standard
speed limit (km/h or mph), when this lim- screen without storing settings.To cancel This function is used to adjust the buzzer
it is exceeded the driver is immediately the setting, proceed as follows: volume used for failure/warning indica-
alerted (see section “Warning lights and tions and when MENU ESC, + and –
messages”). – briefly press button MENU ESC: (On) buttons are pressed.
DEVICES
SAFETY
will blink on the display;
To set the speed limit, proceed as follows: To adjust the volume proceed as follows:
– press button –: (Off) will blink on the
– briefly press button MENU ESC, the display; – briefly press button MENU ESC, the
CORRECT USE
message (SPEEd) and the previously set display will show the wording (bUZZ);
OF THE CAR
unit (km/h) or (mph) will appear on the – briefly press button MENU ESC to go
display; back to the menu screen or press the but- – press button + or – to select the re-
ton for long to go back to the standard quired volume (volume can be adjusted ac-
– press button + or – to activate (on) or screen without storing settings. cording to 8 levels).
deactivate (OFF) the speed limit function;
LIGHTS AND
MESSAGES
WARNING
– briefly press button MENU ESC to go
– if the function is on, press buttons + or Setting the clock (Hour) back to the menu screen or press the but-
– to select the required speed limit and ton for long to go back to the standard
then press MENU ESC to confirm; This function is used to set the clock. screen without storing settings.
EMERGENCY
Note The speed may be set in the range Proceed as follows:
IN AN
from 30 to 200 km/h, or from 20 to 125 – briefly press button MENU ESC,
mph according to the previously chosen “hours” will flash on the display;
unit (see “Setting the distance unit”) de- – press button + or – for setting;
scribed below. The setting will in-
SPECIFICATIONS MAINTENANCE
crease/decrease by five units each time – briefly press button MENU ESC, “min-
CAR
button +/– is pressed. Hold button +/– utes” will flash on the display;
pressed to increase/decrease the setting – press button + or – for setting;
rapidly. Complete the setting by briefly – briefly press button MENU ESC to go
pressing the button when you approach
TECHNICAL
back to the menu screen or press the but-
the required setting. ton for long to go back to the standard
screen without storing settings.
INDEX
21
001-031 LINEA 1ed GB 4-09-2008 14:55 Pagina 22
F0R1001g
AND CONTROLS
DASHBOARD Setting the distance unit (Unit) Front passenger’s airbag
With this function it is possible to set the and side bag
unit. activation/deactivation
(where provided) (BAG P)
To set the required unit proceed as fol-
lows: This function is used to activate/deactivate
MENU ESC
DEVICES
SAFETY
F0R1002g
F0R1003g
OF THE CAR
– press button + or – to select the re- the message (BAG P OFF) (to deacti-
quired distance unit. vate) or (BAG P On) (to activate) is dis-
played by pressing buttons + or –, press
– briefly press button MENU ESC to go again button MENU ESC;
back to the menu screen or press the but-
❒ the confirmation request message will
LIGHTS AND
MESSAGES
WARNING
F0R1005i
F0R1006g
❒ briefly press button MENU ESC to
confirm setting e to go back to the
menu screen or press the button for
SPECIFICATIONS MAINTENANCE
MENU ESC
TECHNICAL
F0R1002g
F0R1003g
INDEX
22
001-031 LINEA 1ed GB 4-09-2008 14:55 Pagina 23
MULTIFUNCTION
AND CONTROLS
DASHBOARD
DISPLAY
(where provided)
The car can be equipped with the multi-
DEVICES
SAFETY
functional display that, according to the
settings made, will show useful informa-
tion necessary when driving.
CORRECT USE
OF THE CAR
F0R0018m F0R0019m
fig. 20 fig. 21
“STANDARD” SCREEN fig. 20
The standard screen shows the following CONTROL BUTTONS fig. 21 Note Buttons + and – activate different
information: functions according to the following situ-
A Date. + To scroll the displayed menu and the ations:
LIGHTS AND
MESSAGES
WARNING
related options upwards or to in-
B Odometer (covered km or miles). crease the value displayed.
C Clock (always displayed, even with ig- To adjust light inside the passenger
nition key removed and front doors compartment
MENU Press briefly to access the menu
closed). ESC and/or go to next screen or to – standard screen, to adjust instrument
EMERGENCY
panel brightness, sound system, and auto-
IN AN
D External temperature. confirm the required menu op-
tion. matic climate control system.
E Headlight aiming position (only with
dipped beam headlights on). Hold pressed to go back to the Setup menu
standard screen.
SPECIFICATIONS MAINTENANCE
Note When opening one of the front – to scroll the menu options upwards and
doors, the display will turn on and show – To scroll the displayed menu and the downwards;
CAR
for a few seconds the clock and the kilo- related options downwards or to de- – to increase or decrease values during set-
metres or miles covered. crease the value displayed. tings.
TECHNICAL
INDEX
23
001-031 LINEA 1ed GB 4-09-2008 14:55 Pagina 24
AND CONTROLS
DASHBOARD SETUP MENU fig. 22 Selecting an option of the main menu with Selecting “Set Date” and
The menu comprises a series of functions submenu: “Set time”:
arranged in a cycle which can be selected – briefly press button MENU ESC to dis- – briefly press button MENU ESC to se-
through buttons + and – to access the dif- play the first submenu option; lect the first value to change (e.g. hours
ferent select operations and settings (set- – press buttons + or – (by single press- /minutes or year / month / day);
up) given in the following paragraphs. A es) to scroll all the submenu options; – press buttons + or – (by single press-
DEVICES
SAFETY
submenu is provided for some items es) to select the new setting;
(Clock and Unit setting). – press briefly button MENU ESC to se-
lect the displayed submenu option and to – briefly press button MENU ESC to store
The setup menu can be activated by press- open the relevant setup menu; the new setting and to go to the next set-
ing briefly button MENU ESC.
CORRECT USE
lect the main menu option to set; at main menu option setting level);
– press buttons + or – (by single press- – to save only the settings stored yet (and
es) to select the new setting; confirmed by pressing button MENU
SPECIFICATIONS MAINTENANCE
the main menu option previously select- The setup menu environment is timed.
ed. Only the changes saved by the user b
briefly pressing MENU ESC will be saved
when the menu is automatically closed.
TECHNICAL
INDEX
24
001-031 LINEA 1ed GB 4-09-2008 14:55 Pagina 25
Example: Example:
AND CONTROLS
DASHBOARD
Türk Nederlands Briefly press MENU ESC on the standard screen to Day
Italiano browse. Press + or – to browse within the menu.
Português Note Only the short menu may be accessed for rea-
Deutsch Polski sons of safety while the car is moving (“Speed Beep” Year Month
setting). Stop the car to access the full menu.
DEVICES
SAFETY
English Français
Español
ESC
+ + MENU
CORRECT USE
OF THE CAR
briefly press
ESC + – – +
MENU RAIN SENSOR
briefly press – SPEED BEEP (where provided ) HEADLIGHTS –
SENSOR
+ (where provided)
LIGHTS AND
MESSAGES
WARNING
EXIT MENU
– TRIP B DATA – +
+ SET TIME
PASSENGER BAG
–
EMERGENCY
– +
IN AN
SERVICE
SET DATE
+
SPECIFICATIONS MAINTENANCE
– –
CAR
SEE RADIO +
BELT BUZZER (*)
– –
TECHNICAL
+ BUTTON VOLUME AUTOCLOSE
+
– WARNING VOLUME UNIT UNIT –
LANGUAGE
+ – – + F0R2004g
INDEX
+ + fig. 21
(*) This function may only be displayed after the SBR system is deactivated by a Fiat Dealership.
25
001-031 LINEA 1ed GB 4-09-2008 14:55 Pagina 26
AND CONTROLS
DASHBOARD Speed limit (Speed Beep) To cancel the setting, proceed as follows: Headlight sensor
This function may be used to set the car – briefly press button MENU ESC: (On) (Automatic headlight sensor
speed limit (km/h or mph); when this lim- will blink on the display; sensitivity adjustment)
it is exceeded the driver is immediately (where provided)
alerted (see section “Warning lights and – press button –: (Off) will flash on the dis-
play; This function is used to adjust the
messages”).
DEVICES
SAFETY
– briefly press button MENU ESC, the ton for long to go back to the standard
according to the previously chosen unit (see screen without storing settings.
“Setting the distance unit”) described below. previously set sensitivity “level” will flash
The setting will increase/decrease by five on the display;
SPECIFICATIONS MAINTENANCE
units each time button +/– is pressed. Hold – press button + or – for setting;
button +/– pressed to increase/decrease the
CAR
setting rapidly. Complete the setting by – briefly press button MENU ESC to go
briefly pressing the button when you ap- back to the menu screen or press the but-
proach the required setting. ton for long to go back to the standard
screen without storing settings.
TECHNICAL
26
001-031 LINEA 1ed GB 4-09-2008 14:55 Pagina 27
AND CONTROLS
Trip B On/Off (tripB data) Setting the clock (Set time) When you have made the required set-
DASHBOARD
This function allows to set the clock through tings, briefly press button MENU ESC
Through this option it is possible to acti- to go back to the menu screen or press
vate (On) or deactivate (Off) the Trip B two sub-menus: “Time” and “Mode”.
the button for long to go back to the stan-
(partial trip). Proceed as follows: dard screen without storing settings.
For further information see “Trip com- – briefly press button MENU ESC, the – hold MENU ESC pressed to go back
DEVICES
SAFETY
puter”. display will show the two sub-menus to the standard screen or main menu ac-
“Time” and “Mode”; cording to the points of the menu where
Proceed as follows to switch the function – press button + or – to surf the two sub-
on and off: you are at.
menus;
CORRECT USE
OF THE CAR
– briefly press button MENU ESC: (On) – select the required option and then Set date (Set Date)
or (Off) will flash on the display (accord- press button MENU ESCbriefly;
ing to previous setting); This function may be used to update the
– when accessing the “Hour” submenu: – date (year - month - day).
– press button + or – for setting; briefly press button MENU ESC,
To correct the date proceed as follows:
LIGHTS AND
MESSAGES
WARNING
“hours” will flash on the display;
– briefly press button MENU ESC to go – briefly press button MENU ESC: “day”
back to the menu screen or press the but- – press button + or – for setting;
– briefly press button MENU ESC, “min- will flash on the display;
ton for long to go back to the standard
screen without storing settings. utes” will flash on the display; – press button + or – for setting;
EMERGENCY
– press button + or – for setting; – briefly press button MENU ESC:
IN AN
– when accessing the “Format” submenu: “month” will flash on the display;
briefly press button MENU ESC : the – press button + or – for setting;
previously set display format will flash on
SPECIFICATIONS MAINTENANCE
the display; – briefly press button MENU ESC:
“year” will flash on the display;
CAR
– press button + or – to select “24h” or
“12h”. – press button + or – for setting.
TECHNICAL
INDEX
27
001-031 LINEA 1ed GB 4-09-2008 14:55 Pagina 28
AND CONTROLS
DASHBOARD Note The setting will increase or de- – press button + or – for setting; button for long to go back to the stan-
crease by one unit each time + or – is dard screen without storing settings.
pressed. Hold the button pressed to in- – briefly press button MENU ESC to go
back to the menu screen or press the but- – hold MENU ESC pressed to go back
crease/decrease the setting rapidly. Com- to the standard screen or main menu ac-
plete the setting by briefly pressing the ton for long to go back to the standard
screen without storing settings. cording to the points of the menu where
button when you approach the required you are at.
DEVICES
SAFETY
setting.
Automatic door locking with car
– briefly press button MENU ESC to go running (Autoclose) Set units (Unit of measure)
back to the menu screen or press the but-
ton for long to go back to the standard When activated (On), this function locks With this function it is possible to set the
CORRECT USE
OF THE CAR
screen without storing settings. automatically the doors when the car units through three sub-menus: “Distances”,
speed exceeds 20 km/h. “Consumption” and “Temperature”.
Audio repetition (See radio) This function is available on all versions Proceed as follows to set the required unit:
With this function the display repeats in- and may only be switched off by means – briefly press button MENU ESC to dis-
LIGHTS AND
MESSAGES
WARNING
formation relevant to the sound system. of the multifunctional display or reconfig- play the three sub-menus;
– Radio: tuned radio station frequency or urable multifunctional display.
– press button + or – to surf the three sub-
RDS message, automatic tuning activation To activate (On) or to deactivate (Off) this menus;
or AutoSTore; function proceed as follows:
EMERGENCY
– CD audio, CD MP3: track number; – briefly press button MENU ESC to dis- press briefly button MENU ESC;
– CD Changer: CD number and track play the three sub-menus;
number; – when accessing the “Distances”submenu:
– briefly press button MENU ESC: (On) briefly press MENU ESC: either “km” or
SPECIFICATIONS MAINTENANCE
To activate (On) or to deactivate (Off) or (Off) will flash on the display (accord- “mi” will appear on the display (according
sound system info displaying proceed as ing to previous setting);
CAR
28
001-031 LINEA 1ed GB 4-09-2008 14:55 Pagina 29
AND CONTROLS
– when you are in the “Consumption” sub- Selecting the language (Language) Adjusting the failure/warning
DASHBOARD
menu: briefly press MENU ESC: either buzzer volume (Buzzer Volume)
“km/l” or “mpg” will appear on the display The messages may be displayed in the fol-
(according to the previous setting); lowing languages: Italian, Turkish, Dutch, With this function the volume of the
Portuguese, Polish, French, Spanish, Eng- buzzer accompanying any failure/warning
If the distance unit set is “km” the fuel con- lish, German. indication can be adjusted according to 8
sumption unit will be displayed in km. levels.
DEVICES
SAFETY
To set the required language proceed as
If the distance unit set is “mi” the fuel con- follows: To adjust the volume proceed as follows:
sumption unit will be displayed in “mpg”. – briefly press button MENU ESC: the
– briefly press button MENU ESC: the
CORRECT USE
– press button + or – for setting; previously set “language” “ will flash on the previously set volume “level” will flash on
OF THE CAR
display; the display;
– when accessing the “Temperature”sub-
menu: briefly press MENU ESC: either – press button + or – for setting; – press button + or – for setting;
“°C” or “°F” will appear on the display (ac- – briefly press button MENU ESC to go – briefly press button MENU ESC to go
cording to the previous setting);
LIGHTS AND
MESSAGES
WARNING
back to the menu screen or press the but- back to the menu screen or press the but-
– press button + or – for setting; ton for long to go back to the standard ton for long to go back to the standard
When you have made the required set- screen without storing settings. screen without storing settings.
tings, briefly press button MENU ESC to
EMERGENCY
go back to the menu screen or press the
IN AN
button for long to go back to the standard
screen without storing settings.
– hold MENU ESC pressed to go back
to the standard screen or main menu ac-
SPECIFICATIONS MAINTENANCE
cording to the points of the menu where
CAR
you are at.
TECHNICAL
INDEX
29
001-031 LINEA 1ed GB 4-09-2008 14:55 Pagina 30
AND CONTROLS
DASHBOARD Adjusting the button volume Scheduled Servicing (Service) Note The “Service Schedule” requires the
(Button Vol.) car to be serviced every 30,000 km (or
Through this function it is possible to dis- 18,000 mi) or every 20,000 km (where
This function may be used to adjust the play information connected to proper car provided); this indication will appear au-
volume of the beep accompanying the ac- servicing. tomatically with the key at MAR when
tivation of buttons MENU ESC, + and Proceed as follows: there are 2000 km left (or 1240 mi) and
DEVICES
back to the menu screen or press the but- the key is turned to MAR. Go to a Fiat
ton for long to go back to the standard Dealership where the “Scheduled Service”
screen without storing settings. operations will be performed and the mes-
sage will be reset.
EMERGENCY
IN AN
SPECIFICATIONS MAINTENANCE
TECHNICAL CAR
INDEX
30
001-031 LINEA 1ed GB 4-09-2008 14:55 Pagina 31
F0R1009g
AND CONTROLS
Passenger front and side airbag Exit Menu
DASHBOARD
activation/deactivation This is the last function that closes the cir-
(where provided) (passenger bag) cular setting cycle listed in the initial menu
This function shall be used to activate/de- screen.
activate the front passenger’s airbag. MENU ESC
+ + Briefly press button MENU ESC to go
DEVICES
SAFETY
Proceed as follows: – – back to the standard screen without stor-
ing settings.
❒ press button MENU ESC and press
F0R1010g
F0R1011g
MENU ESC again after the message Press button – to return to the first menu
CORRECT USE
option (Speed Beep).
OF THE CAR
(Bag pass: Off) (to deactivate) or (Bag
pass: On) (to activate) is displayed by
pressing buttons + and –; MENU ESC
❒ display will show the confirmation mes-
+ +
LIGHTS AND
sage;
MESSAGES
WARNING
– –
❒ press buttons + or – to select (Yes)
(confirming activation/deactivation) or
F0R1013g
F0R1014g
(No) (to abort);
EMERGENCY
❒ briefly press button MENU ESC to
IN AN
confirm setting e to go back to the
menu screen or press the button for MENU ESC
long to go back to the standard screen
+ +
SPECIFICATIONS MAINTENANCE
without storing settings.
– –
CAR
F0R1009g
F0R1009g
TECHNICAL
MENU ESC
INDEX
F0R1015g
F0R1016g
31
032-043 LINEA 1ed GB 3-09-2008 17:28 Pagina 32
AND CONTROLS
DASHBOARD
RECONFIGURABLE
MULTIFUNCTION
DISPLAY
(where provided)
DEVICES
SAFETY
F0R2010g F0R0241m
fig. 23/a fig. 23/b
information:
MESSAGES
WARNING
C Sport driving mode indication (where confirm the required menu op-
IN AN
provided) tion.
D Odometer (distance travelled in kilo- Long press to go back to the F0R0019m
fig. 24
metres/miles) standard screen.
SPECIFICATIONS MAINTENANCE
E Car conditions (e.g. doors open, ice on – To scroll the displayed menu and the Note Buttons + and – activate different
CAR
road, etc.) related options downwards or to de- functions according to the following situ-
crease the value displayed. ations:
F Headlight aiming position (with dipped
beam headlights on only) – to scroll the menu options upwards and
TECHNICAL
When rotating the ignition key to MAR – to increase or decrease values during
position, the display shows, as main settings.
screen, the indication of the date fig.23/a Note When opening one of the front
INDEX
or the overpressure of the turbo-charg- doors, the display will turn on and show
er fig.23/b according to the previous se- for a few seconds the clock and the km or
lection in the menu item “First screen” mi covered.
(“Date” or “Engine Info”).
32
032-043 LINEA 1ed GB 3-09-2008 17:28 Pagina 33
AND CONTROLS
SETUP MENU fig. 25 Selecting an option of the main menu Selecting an option of the main menu with
DASHBOARD
without submenu submenu:
The menu comprises a series of functions
arranged in a “circular fashion” which can – press briefly button MENU ESC to se- – press briefly button MENU ESC to dis-
be selected through buttons + and – to lect the main menu option to set; play the first submenu option;
access the different select operations and
settings (setup) given in the following para- – press buttons + or – (by single press- – press buttons + or – (by single press-
DEVICES
SAFETY
graphs. A submenu is provided for some es) to select the new setting; es) to scroll all the submenu options;
items (Clock and Unit setting). – press briefly button MENU ESC to – press briefly button MENU ESC to se-
The setup menu can be activated by press- store the new setting and to go back to lect the displayed submenu option and to
CORRECT USE
the main menu option previously select- open the relevant setup menu;
OF THE CAR
ing briefly button MENU ESC.
ed.
Single presses on buttons + or – will scroll – press buttons + or – (by single press-
the setup menu options. Management es) to select the new setting for this sub-
modes differ with each other according to menu option;
LIGHTS AND
MESSAGES
WARNING
the characteristic of the option selected. – press briefly button MENU ESC to
store the new setting and to go back to
the previously selected submenu option.
EMERGENCY
IN AN
SPECIFICATIONS MAINTENANCE
TECHNICAL
INDEX CAR
33
032-043 LINEA 1ed GB 3-09-2008 17:28 Pagina 34
Example:
AND CONTROLS
DASHBOARD
On the standard screen, briefly press MENU ESC to start brows- Day
ing. Press + or – to browse within the menu. Note Only the short
menu may be accessed for reasons of safety while the car is moving Year Month
Türk Nederlands
(“Brightness” and “Speed Beep”). Stop the car to access the full menu.
Italiano Português
DEVICES
SAFETY
PASSENGER BAG
– TRIP B DATA
+ SERVICE
– +
EMERGENCY
–
IN AN
SET TIME
+ BELT BUZZER –
SPECIFICATIONS MAINTENANCE
– +
CAR
SET DATE
BUTTON VOL.
–
FIRST PAGE
+ – +
TECHNICAL
BUZZER VOL.
–
SEE RADIO
– LANGUAGE AUTOCLOSE – +
UNIT
INDEX
F0R2005g
+ – –
+ fig. 25
+ +
34
032-043 LINEA 1ed GB 3-09-2008 17:28 Pagina 35
AND CONTROLS
Speed beep (Speed limit) Note The speed may be set in the range – briefly press button MENU ESC to go
DASHBOARD
from 30 to 200 km/h, or from 20 to 125 back to the menu screen or press the but-
This function is used to set the car speed mph according to the previously chosen ton for long to go back to the standard
limit (km/h or mph); when this limit is ex- unit (see “Setting the distance unit”) de- screen without storing settings.
ceeded the driver is immediately alerted scribed below. The setting will in-
(see section “Warning lights and mes- crease/decrease by five units each time To cancel the setting, proceed as follows:
sages”).
DEVICES
SAFETY
button +/– is pressed. Hold button +/– – briefly press button MENU ESC: (On)
To set the speed limit, proceed as follows: pressed to increase/decrease the setting will blink on the display;
rapidly. Complete the setting by briefly
– briefly press button MENU ESC, the pressing the button when you approach – press button –: (Off) will flash on the dis-
CORRECT USE
display will show the wording (Speed play;
OF THE CAR
the required setting.
Buzz);
– briefly press button MENU ESC to go
– press button + or – to select speed lim- back to the menu screen or press the but-
it activation (On) or deactivation (Off); ton for long to go back to the standard
screen without storing settings.
LIGHTS AND
MESSAGES
WARNING
– if the function has been activated (On),
press buttons + or – to select the re-
quired speed limit and then press MENU
ESC to confirm.
EMERGENCY
IN AN
SPECIFICATIONS MAINTENANCE
TECHNICAL
INDEX CAR
35
032-043 LINEA 1ed GB 3-09-2008 17:28 Pagina 36
AND CONTROLS
DASHBOARD Rain sensor sensitivity adjustment – press button + or – for setting; Setting the time (Clock)
(Rain sensor) (where provided) – briefly press button MENU ESC to go This function allows to set the clock
With this function it is possible to adjust back to the menu screen or press the but- through two sub-menus: “Time” and
the rain sensor sensitivity according to 4 ton for long to go back to the standard “Mode”.
levels. screen without storing settings. Proceed as follows:
DEVICES
SAFETY
on the display;
For further information see “Trip com- the two submenus;
– press button + or – for setting;
puter”. – select the required option and then
– briefly press button MENU ESC to go
back to the menu screen or press the but- Proceed as follows to switch the function press button MENU ESCbriefly;
LIGHTS AND
– press button + or – for setting; – briefly press button MENU ESC, “min-
IN AN
sensitivity adjustment)
utes” will flash on the display;
(where provided) – briefly press button MENU ESC to go
back to the menu screen or press the but- – press button + or – for setting.
This function is used to adjust the dusk
ton for long to go back to the standard
SPECIFICATIONS MAINTENANCE
36
032-043 LINEA 1ed GB 3-09-2008 17:28 Pagina 37
AND CONTROLS
Note The setting will increase or de- Set date (Set Date) First screen (information displayed
DASHBOARD
crease by one unit each time + or – is in the main screen)
pressed. Hold the button pressed to in- This function may be used to update the
date (year - month - day). (where provided)
crease/decrease the setting rapidly. Com-
plete the setting by briefly pressing the To correct the date proceed as follows: This function enables to select the type of
button when you approach the required information displayed in the main screen.
DEVICES
– briefly press button MENU ESC:
SAFETY
setting. It is possible to display the date or the
“year” will flash on the display; pressure of the turbo-compressor.
– when accessing the “Format” submenu:
briefly press button MENU ESC: the – press button + or – for setting; To select one of the two items, proceed
previously set display format will flash on as follows:
CORRECT USE
OF THE CAR
– briefly press button MENU ESC:
the display; “month” will flash on the display; – push the button MENU ESC for a
– press button + or – to select “24h” or short time, “First screen” is displayed;
“12h”. – press button + or – for setting;
– press again the button MENU ESC for
– briefly press button MENU ESC: “day”
LIGHTS AND
When you have made the required set- a short time to display the “Date” and
MESSAGES
WARNING
tings, briefly press button MENU ESC to will flash on the display; “Engine Info” options;
go back to the menu screen or press the – press button + or – for setting.
button for long to go back to the standard – press + or – to select the type of infor-
screen without storing settings. Note The setting will increase or de- mation to be displayed in the main screen;
EMERGENCY
crease by one unit each time + or – is – press MENU ESC for a short time to
IN AN
– hold MENU ESC pressed to go back pressed. Hold the button pressed to in-
to the standard screen or main menu ac- store the selection and return to the pre-
crease/decrease the setting rapidly. Com- vious screen or press the button for a
cording to the points of the menu where plete the setting by briefly pressing the
you are at. longer time to return to the standard
button when you approach the required
SPECIFICATIONS MAINTENANCE
screen without storing the selection.
setting.
CAR
Rotating the ignition key on MAR, the re-
– briefly press button MENU ESC to go configurable multifunctional display, after
back to the menu screen or press the but- the start-up check, displays the previous-
ton for long to go back to the standard ly set information using the “First screen”
TECHNICAL
screen without storing settings. function of the menu.
INDEX
37
032-043 LINEA 1ed GB 3-09-2008 17:28 Pagina 38
AND CONTROLS
DASHBOARD See radio Autoclose Unit of measure (Set units)
(Repeat audio information) (Automatic door lock operation This function may be used to set the unit
This function is used to display informa- with car running) for measure in three submenus: “Dis-
tion relevant to the sound system. When activated (On), this function locks tances”, “Consumption” and “Tempera-
automatically the doors when the car ture”.
– Radio: tuned radio station frequency or
DEVICES
RDS message, automatic tuning activation Proceed as follows to set the required
or AutoSTore; This function is available on all versions unit:
– CD audio, CD MP3: track number; and may only be switched off by means – briefly press button MENU ESC to dis-
of the multifunctional display or reconfig-
CORRECT USE
ton for long to go back to the standard menu: briefly press MENU ESC: either
screen without storing settings. ton for long to go back to the standard “km/l”, “l/100km” or “mpg” will appear on
CAR
screen without storing settings. the display (according to the previous set-
– hold MENU ESC pressed to go back to ting);
the standard screen or main menu accord- If the distance unit set is “km” the fuel con-
TECHNICAL
ing to the points of the menu where you are sumption unit will be displayed in km/l or
at. l/100km.
INDEX
38
032-043 LINEA 1ed GB 3-09-2008 17:28 Pagina 39
AND CONTROLS
If the distance unit set is “mi” the fuel con- Language (Selecting the language) Buzzer volume (Adjusting the
DASHBOARD
sumption unit will be displayed in “mpg”. failure/warning buzzer volume)
The messages may be displayed in the fol-
– press button + or – for setting; lowing languages: Italian, German, With this function the volume of the
English, Spanish, French, Portuguese, buzzer accompanying any failure/warning
– when accessing the “Temperature” sub- Dutch.
menu: briefly press MENU ESC: either indication can be adjusted according to 8
DEVICES
levels.
SAFETY
“°C” or “°F” will appear on the display ac- To set the required language proceed as
cording to the previous setting; follows: To adjust the volume proceed as follows:
– press button + or – for setting; – briefly press button MENU ESC: the – briefly press button MENU ESC: the
CORRECT USE
previously set “language” “ will flash on the
OF THE CAR
When you have made the required set- previously set volume “level” will flash on
display; the display;
tings, briefly press button MENU ESC to
go back to the menu screen or press the – press button + or – for setting; – press button + or – for setting;
button for long to go back to the standard
screen without storing settings. – briefly press button MENU ESC to go – briefly press button MENU ESC to go
LIGHTS AND
MESSAGES
WARNING
back to the menu screen or press the but- back to the menu screen or press the but-
– hold MENU ESC pressed to go back ton for long to go back to the standard ton for long to go back to the standard
to the standard screen or main menu ac- screen without storing settings. screen without storing settings.
cording to the points of the menu where
you are at.
EMERGENCY
IN AN
SPECIFICATIONS MAINTENANCE
TECHNICAL
INDEX CAR
39
032-043 LINEA 1ed GB 3-09-2008 17:28 Pagina 40
AND CONTROLS
DASHBOARD Button volume Service (Scheduled servicing) Note The “Service Schedule” requires the
(Button volume adjustment) car to be serviced every 30,000 km (or
This function may be used to display in- 18,000 mi) or every 20,000 km (12,000 mi)
This function may be used to adjust the formation connected to proper car ser- (where provided); this indication will ap-
volume of the beep accompanying the ac- vicing. pear automatically with the key at MAR
tivation of buttons MENU ESC, + and Proceed as follows: when there are 2000 km left (or equiva-
– can be adjusted according to 8 levels.
DEVICES
SAFETY
back to the menu screen or press the but- followed by the number of kilometres or
ton for long to go back to the standard miles left when the key is turned to MAR.
screen without storing settings. Go to a Fiat Dealership where the “Sched-
uled Service” operations will be per-
formed and the message will be reset.
EMERGENCY
40
032-043 LINEA 1ed GB 3-09-2008 17:28 Pagina 41
F0R2006g
AND CONTROLS
Passenger bag Front passenger’s Exit Menu
DASHBOARD
airbag and side bag This is the last function that closes the cir-
activation/deactivation cular setting cycle listed in the initial menu
(where provided) screen.
This function may be used to activate/de- Briefly press button MENU ESC to go
DEVICES
SAFETY
activate the front passenger’s airbag. + back to the standard screen without stor-
MENU ESC ing settings.
Proceed as follows: –
– press MENU ESC and press MENU Press button – to return to the first menu
F0R2007g
CORRECT USE
option (Speed Beep).
OF THE CAR
ESC again after displaying the message
(Bag pass: Off, to deactivate) or (Bag pass:
On, to activate) by means of buttons
+ and –;
LIGHTS AND
MESSAGES
– the confirmation request message will
WARNING
be displayed; +
MENU ESC
– press buttons + or – to select (Yes) for –
confirming activation/deactivation, or (No)
F0R2008g
EMERGENCY
to abort;
IN AN
– briefly press MENU ESC to confirm
setting e to go back to the menu screen
or press the button for long to go back to
SPECIFICATIONS MAINTENANCE
the standard screen without storing set-
tings.
TECHNICAL
INDEX CAR
41
032-043 LINEA 1ed GB 3-09-2008 17:28 Pagina 42
AND CONTROLS
DASHBOARD
TRIP COMPUTER “Trip B”, available on multifunctional dis- Values displayed
play only, shall be used to display the fig-
ures relating to: Range
General features This indicates the distance which may be
– Trip distance B
The “Trip computer” is used to display in- travelled with the fuel in the tank
formation on car operation when the key – Average consumption B assuming that driving conditions will not
DEVICES
SAFETY
is turned to MAR. This function allows to change. The message “——” will appear
– Average speed B on the display in the following cases:
define two separate trips called “Trip A”
and “Trip B” for monitoring the car’s – Travel time B (driving time). – range shorter than 50 km (or 30 mi)
“complete mission” in a reciprocally in-
CORRECT USE
– Average consumption
– Instant consumption
– Average speed
SPECIFICATIONS MAINTENANCE
42
032-043 LINEA 1ed GB 3-09-2008 17:28 Pagina 43
AND CONTROLS
Average consumption – after disconnecting/reconnecting the
DASHBOARD
battery.
This indicates the average consumption
from the start of the new mission. IMPORTANT The reset operation in the
presence of the screens concerning the
Instant consumption “Trip A” makes it possible to reset only
the information associated with this func-
DEVICES
This indicates the fuel consumption. The
SAFETY
value is constantly updated. The message tion.
“----” will appear on the display IMPORTANT The reset operation in the
if the car is parked with the engine run- presence of the screens concerning the
CORRECT USE
ning.
OF THE CAR
F0R0020m
fig. 26 “Trip B” makes it possible to reset only
Average speed the information associated with this func-
TRIP button fig. 26 tion.
This shows the car average speed as a
function of the overall time elapsed since Button TRIP, set on the top of the right
Start of journey procedure
LIGHTS AND
steering column stalk, shall be used (with
MESSAGES
WARNING
the start of the new mission.
ignition key at MAR) to display and to re- With ignition key at MAR, press and keep
Travel time set the previously described values to start button TRIP pressed for over 2 seconds
This value shows the time elapsed since a new mission: to reset.
the start of the new mission. – briefly press to display the different val-
EMERGENCY
ues
IN AN
IMPORTANT If information is not avail- Exit Trip
able, the message “----” will appear instead – hold pressed to reset and then start a
new mission. To exit the Trip function: hold MENU
of the Trip Computer values. Displaying ESC pressed for longer than 2 seconds.
SPECIFICATIONS MAINTENANCE
of the values will be resumed when nor-
mal operation is restored without reset- New mission
CAR
ting the values displayed before the prob- Reset can be:
lem nor starting a new mission. – “manual” resetting by the user, by press-
ing the relevant button;
TECHNICAL
– “automatic” resetting, when the “Trip dis-
tance” reaches 3999.9 km or 9999.9 km
(according to the type of display) or when
the “Travel time” reaches 99.59 (99 hours
and 59 minutes);
INDEX
43
044-090 LINEA 1ed GB 3-09-2008 17:29 Pagina 44
AND CONTROLS
DASHBOARD
FRONT SEATS Back rest angle adjustment fig. 27
Turn knob C.
WARNING
All adjustments must be
made with the car stationary. WARNING
DEVICES
SAFETY
F0R0021m
fig. 27
The fabric upholstery of your chest and hips.
car is designed to withstand
the normal wear and tear of WARNING
your car for a long time. Some After releasing the lever, al-
LIGHTS AND
of the car.
threads and damage the upholstery.
SPECIFICATIONS MAINTENANCE
44
044-090 LINEA 1ed GB 3-09-2008 17:29 Pagina 45
AND CONTROLS
DASHBOARD
To folds the rear seats refer to paragraph
“Extending the boot” in this section. FRONT fig. 29
On certain versions head restraints are ad-
justable in height and they lock automati-
DEVICES
SAFETY
cally in the required position.
The fabric upholstery of your
car is designed to withstand To adjust head restraints proceed as fol-
the normal wear and tear of lows:
CORRECT USE
OF THE CAR
F0R0022m
fig. 28
your car for a long time. ❒ upward adjustment: raise the head re-
Some precautions are however need- straint until you hear it click.
Electric lumbar adjustment ed. Avoid prolonged rubbing against
(where provided) fig. 28 clothing accessories, such as metal
LIGHTS AND
buckles, Velcro strips and the like,
MESSAGES
WARNING
For electric lumbar adjustment, use con-
trols E. which by applying a high pressure on
the fabric in a small area could cause
the breakage of some threads and
damage the upholstery.
EMERGENCY
IN AN
SPECIFICATIONS MAINTENANCE
TECHNICAL
INDEX CAR
45
044-090 LINEA 1ed GB 3-09-2008 17:29 Pagina 46
AND CONTROLS
DASHBOARD To lift out rear head restraints: press at
the same time buttons A and B set on
both sides and take them out.
IMPORTANT Rear seat passengers shall
always set the head restraints in the po-
sition of use.
DEVICES
SAFETY
CORRECT USE
OF THE CAR
F0R0024m F0R0025m
fig. 29 fig. 30
To lift out front head restraints: press at ing the click (position of use).
the same time buttons A and B set on
both sides and take them out. To bring it back to the original position
(position of non use), press button A and
push the head restraint down into the
EMERGENCY
back rest.
IN AN
WARNING
The head restraints must be
adjusted so that they sup-
SPECIFICATIONS MAINTENANCE
restraint.
46
044-090 LINEA 1ed GB 3-09-2008 17:29 Pagina 47
AND CONTROLS
DASHBOARD
The driver can adjust the steering wheel
position both axially and in height. DRIVING MIRROR fig. 32
Proceed as follows: The mirror is fitted with a safety device
that causes it to be released in the event
DEVICES
SAFETY
❒ release the lever A-fig. 31 pushing it of a violent crash.
forwards (position 2);
❒ adjust the steering wheel as required;
CORRECT USE
OF THE CAR
F0R0026m
fig. 31
❒ lock the lever A pulling it towards the
steering wheel (position 1).
WARNING
Any adjustment of the steer-
LIGHTS AND
MESSAGES
WARNING
ing wheel position must be
carried out only with the car station-
ary and the engine turned off.
EMERGENCY
IN AN
WARNING
It is absolutely forbidden to
SPECIFICATIONS MAINTENANCE
carry out whatever after-
CAR
market operation involving steering
system or steering column modifica-
tions (e.g.: installation of anti-theft
device) that could badly affect per-
TECHNICAL
formance and safety, cause the lapse
of warranty and also result in non-
compliance of the car with homolo-
gation requirements.
INDEX
47
044-090 LINEA 1ed GB 3-09-2008 17:29 Pagina 48
AND CONTROLS
DASHBOARD
DEVICES
SAFETY
CORRECT USE
OF THE CAR
C in the four directions; Mirrors are fitted with resistors that will
The mirror can be adjusted to two differ-
CAR
ror. Button ON/OFF on the lower part it is possible to fold the mirror moving it later.
of the window is used to switch the elec- from position 1-fig. 34 to position 2.
trochromic function on and off. Switch on
to shade the mirror for daytime use. WARNING
As the driver’s door mirror is
INDEX
48
044-090 LINEA 1ed GB 3-09-2008 17:29 Pagina 49
AND CONTROLS
DASHBOARD
F0R0031m
DEVICES
SAFETY
CORRECT USE
OF THE CAR
LIGHTS AND
MESSAGES
WARNING
EMERGENCY
IN AN
SPECIFICATIONS MAINTENANCE
TECHNICAL CAR
fig. 36
INDEX
1. Upper fixed vent - 2. Adjustable central vents - 3. Fixed side vent - 4. Adjustable side vents - 5. Lower vents for front seats -
6. Lower side vents for rear seats - 7. Lower central vent for rear seats (where provided).
49
044-090 LINEA 1ed GB 3-09-2008 17:29 Pagina 50
AND CONTROLS
DASHBOARD
DEVICES
SAFETY
CORRECT USE
OF THE CAR
F0R0032m
fig. 37
LIGHTS AND
MESSAGES
WARNING
EMERGENCY
IN AN
F0R0034m
fig. 39
F0R0033m
fig. 38
Fan on/off and speed adjustment
SPECIFICATIONS MAINTENANCE
CONTROLS fig. 39
ADJUSTABLE SIDE AND knob B
CAR
50
044-090 LINEA 1ed GB 3-09-2008 17:29 Pagina 51
AND CONTROLS
Air distribution knob C VENTILATION FAST HEATING
DASHBOARD
¶ to convey air to the central and side To ventilate the passenger’s compartment For fast heating of the passenger com-
vents; properly proceed as follows: partment, proceed as follows:
ß to warm the feet and convey cooler ❒ knob A turned to blue section; ❒ turn knob A to the red sector;
air to the dashboard vents, in inter-
❒ switch internal air recirculation off; ❒ switch internal air recirculation on;
DEVICES
SAFETY
mediate temperature conditions;
❒ turn knob C to ¶; ❒ turn knob C to ¶;
© for heating when the outside temper-
ature is very cold: for maximum air ❒ turn knob B to required speed. ❒ knob B turned to 4 - (max. fan
CORRECT USE
flow to feet; speed).
OF THE CAR
® to warm the feet and demist the wind- WARMING THE PASSENGER Then use the controls to keep the re-
screen at the same time; COMPARTMENT quired comfort conditions and press but-
- for quick windscreen demisting. Proceed as follows: ton D to ¶ to turn air recirculation off
(button led off) and to prevent misting up.
LIGHTS AND
MESSAGES
WARNING
❒ turn knob A to the red sector;
Air recirculation on/off slider D IMPORTANT With cold engine, you have
❒ turn knob C to the required position; to wait for a few minutes to let the sys-
Take the slider to position v to re- tem fluid reach the operating temperature.
circulate internal air. ❒ turn knob B to required speed.
EMERGENCY
IN AN
Take the slider to position ¶ to switch
internal air recirculation off.
SPECIFICATIONS MAINTENANCE
TECHNICAL
INDEX CAR
51
044-090 LINEA 1ed GB 3-09-2008 17:29 Pagina 52
AND CONTROLS
DASHBOARD FRONT WINDOW FAST Window demisting
DEMISTING/ In the event of considerable outside mois-
DEFROSTING (WINDSCREEN ture and/or rain and/or considerable dif-
AND SIDE WINDOWS) ferences in temperature inside and outside
Proceed as follows: the passenger compartment, perform the
following preventive demisting procedure:
DEVICES
SAFETY
F0R0035m
❒ turn knob C to -. Change it to posi- fig. 40
❒ knob B turned to 4 - (max. fan tion con ® if demisting is insufficient;
speed). HEATED REAR WINDOW
❒ turn knob B to 2nd speed.
After demisting/defrosting, operate the AND DOOR MIRROR
LIGHTS AND
DEMISTING/DEFROSTING
MESSAGES
WARNING
on.
IN AN
52
044-090 LINEA 1ed GB 3-09-2008 17:29 Pagina 53
MANUAL CLIMATE
AND CONTROLS
INTERNAL AIR IMPORTANT The inside air recirculation
DASHBOARD
RECIRCULATION system makes it possible to reach the re-
quired “heating” or “cooling” conditions CONTROL SYSTEM
Move slider D to position v to switch faster. (where provided)
internal air recirculation on.
Do not use the air recirculation function
It is advisable to switch internal air recir- on rainy/cold days as it would consider-
DEVICES
SAFETY
culation on while standing in queues or in CONTROLS fig. 41
ably increase the possibility of the win-
tunnels to prevent the introduction of pol- dows misting up.
luted air. Do not use the function for a Air temperature knob A
long time, particularly if there are many (mixing hot and cold air)
CORRECT USE
OF THE CAR
occupants on board, to prevent the win-
dows from misting up. Red section = hot air
Blue section = cold air
LIGHTS AND
MESSAGES
Fan activation /speed adjustment
WARNING
knob B
p 0 = fan off
1-2-3 = ventilation speed
EMERGENCY
IN AN
4 - = maximum fan speed
SPECIFICATIONS MAINTENANCE
TECHNICAL
INDEX CAR
53
044-090 LINEA 1ed GB 3-09-2008 17:29 Pagina 54
AND CONTROLS
DASHBOARD Air recirculation on/off slider D
Take the slider to position v to recir-
culate internal air.
Take the slider to position ¶to switch
internal air recirculation off.
DEVICES
SAFETY
off.
EMERGENCY
IN AN
F0R0036m
fig. 41
Air distribution knob C ® to warm the feet and at the same time
SPECIFICATIONS MAINTENANCE
54
044-090 LINEA 1ed GB 3-09-2008 17:29 Pagina 55
AND CONTROLS
VENTILATION CLIMATE CONTROL (cooling) Cooling adjustment
DASHBOARD
To ventilate the passenger’s compartment For fast cooling of the passenger com- ❒ turn knob A rightwards to increase the
properly proceed as follows: partment, proceed as follows: temperature;
❒ knob A turned to blue section; ❒ knob A turned to blue section; ❒ switch internal air recirculation off;
❒ switch internal air recirculation off; ❒ switch internal air recirculation on; ❒ turn knob B to increase fan speed.
DEVICES
SAFETY
❒ turn knob C to ¶; ❒ turn knob C to ¶;
❒ turn knob B to required speed. ❒ switch the climate control system on
CORRECT USE
by pressing knob E: the LED on the
OF THE CAR
knob will light up;
❒ turn knob B to 4 - (maximum speed
of fan).
LIGHTS AND
MESSAGES
WARNING
EMERGENCY
IN AN
SPECIFICATIONS MAINTENANCE
TECHNICAL
INDEX CAR
55
044-090 LINEA 1ed GB 3-09-2008 17:29 Pagina 56
AND CONTROLS
DASHBOARD WARMING THE PASSENGER FAST HEATING FRONT WINDOW FAST
COMPARTMENT For fast heating of the passenger com- DEMISTING/DEFROSTING
Proceed as follows: partment, proceed as follows: (WINDSCREEN AND SIDE
WINDOWS)
❒ turn knob A to the red sector; ❒ turn knob A to the red sector;
Proceed as follows:
❒ turn knob C to the required symbol; ❒ switch internal air recirculation on;
DEVICES
SAFETY
speed).
OF THE CAR
❒ turn knob C to -;
Then adjust the controls to obtain the re-
quired conditions of comfort and switch ❒ switch internal air recirculation off.
internal air recirculation off.
LIGHTS AND
MESSAGES
WARNING
56
044-090 LINEA 1ed GB 3-09-2008 17:29 Pagina 57
AND CONTROLS
After demisting/defrosting, operate the Window demisting
DASHBOARD
controls to restore the required comfort.
In the event of considerable outside mois-
IMPORTANT The climate control system ture and/or rain and/or considerable dif-
is very useful for faster demisting because ferences in temperature inside and outside
it dries the air. Adjust the controls as de- the passenger compartment, perform the
scribed above and press knob E to switch following preventive demisting procedure:
DEVICES
SAFETY
the climate control system on: the LED on
the knob will light up. ❒ turn knob A to the red sector;
❒ switch internal air recirculation off;
CORRECT USE
OF THE CAR
F0R0035m
❒ turn knob C to - and change it back fig. 42
to ® if demisting does not improve;
HEATED REAR WINDOW AND
❒ turn knob B to 2nd speed.
DOOR MIRROR DEMISTING/
IMPORTANT The climate control system
LIGHTS AND
DEFROSTING (where provided)
MESSAGES
WARNING
is very useful to prevent window misting fig. 42
up in presence of high humidity since it
dries the air. Press button A to start this function;
when this function is on the button led is
EMERGENCY
on.
IN AN
This function is timed and it will turn off
automatically after 20 minutes. Press A
again to switch it off before.
SPECIFICATIONS MAINTENANCE
IMPORTANT Do not apply stickers on
CAR
the inside of the rear window over the
heating filaments to avoid damage that
might cause it to stop working properly.
TECHNICAL
INDEX
57
044-090 LINEA 1ed GB 3-09-2008 17:29 Pagina 58
AND CONTROLS
DASHBOARD AIR RECIRCULATION IMPORTANT The inside air recirculation LOOKING AFTER THE SYSTEM
system makes it possible to reach the re-
Move slider D to position v to switch quired “heating” or “cooling” conditions Run the climate control system for at least
internal air recirculation on. faster. 10 minutes every month during the win-
ter. Have the system inspected at a Fiat
It is advisable to switch internal air recir- Do not use the air recirculation function Dealership before the summer.
culation on while standing in queues or in on rainy/cold days as it would consider-
DEVICES
SAFETY
tunnels to prevent the introduction of pol- ably increase the possibility of the win-
luted air. Do not use the function for a dows misting inside.
long time, particularly if there are many
occupants on board, to prevent the win- The system uses R134a re-
CORRECT USE
EMERGENCY
IN AN
SPECIFICATIONS MAINTENANCE
TECHNICAL CAR
INDEX
58
044-090 LINEA 1ed GB 3-09-2008 17:29 Pagina 59
AUTOMATIC CLIMATE
AND CONTROLS
The automatically controlled parameters All functions may be manually changed. In
DASHBOARD
and functions are: order words, you may select one or more
CONTROL SYSTEM functions and change the parameters as
❒ air temperature at the vents;
(where provided) required. Automatic control of the man-
❒ air distribution at the vents; ually changed functions will be suspended:
the system will change override your set-
❒ fan speed (continuous air flow varia-
DEVICES
SAFETY
GENERAL tings only for safety related reasons (e.g.
tion); risk of misting up).
The automatic climate control system ad-
justs the temperature, the quantity and the ❒ compressor fan on (for cooling/dehu- Manual selections will always have higher
distribution of the air in the passenger midifying the air); priority over automatic settings and will
CORRECT USE
OF THE CAR
compartment. Temperature is controlled ❒ air recirculation. be stored until the user switches the sys-
on the basis of an “equivalent tempera- tem back to automatic control by press-
ture” principle; in other words, the sys- ing AUTO expect for the cases in which
tem continuously works to keep the com- the system will intervene for particular,
LIGHTS AND
fort level inside the car constant and to safety-related reasons.
MESSAGES
WARNING
compensate for possible variations of ex-
ternal conditions, including sun radiation You can adjust one function automatical-
detected by a specific sensor. ly and have the automatic system control
all the others.
EMERGENCY
The air temperature is always automati-
IN AN
cally controlled according to the temper-
ature shown on the display (except for
when the system is off or in certain con-
SPECIFICATIONS MAINTENANCE
ditions when the compressor is not run-
ning).
TECHNICAL
INDEX CAR
59
044-090 LINEA 1ed GB 3-09-2008 17:29 Pagina 60
AND CONTROLS
DASHBOARD The following parameters and functions
can be set or changed manually:
❒ air temperature;
❒ fan speed (continuous variation);
❒ air distribution setting to seven posi-
DEVICES
SAFETY
tions;
❒ compressor enabling;
CORRECT USE
❒ fast defrosting/demisting;
OF THE CAR
❒ air recirculation;
❒ system off.
LIGHTS AND
MESSAGES
WARNING
EMERGENCY
IN AN
F0R0148m
fig. 43
C Display.
D MAX DEF function button.
E System off button.
INDEX
60
044-090 LINEA 1ed GB 3-09-2008 17:29 Pagina 61
AND CONTROLS
USING THE CLIMATE During completely automatic system op- Air temperature adjustment
DASHBOARD
CONTROL SYSTEM eration, you can vary the set temperature, knob (I)
the air distribution and the fan speed us-
The system can be started in different ing the corresponding buttons or knobs Turn the knob either clockwise or anti-
ways, but it is advisable to start by press- at any time: the system will automatically clockwise to increase or lower the re-
ing the AUTO button and then turning change settings to adapt to the new re- quested temperature in the passenger
the knobs to set the temperature required compartment. The set temperature is
DEVICES
SAFETY
quest.
on the display. shown on the display.
During fully automatic operation (FULL
The system will start running automatically AUTO), the word FULL will disappear Turn the knob either all to the right or
in this way and the set comfortable tem- if the air distribution, air speed, compres- all to the left to the extreme HI or LO
CORRECT USE
OF THE CAR
perature will be reached as quickly as pos- sor and/or recirculation settings are position to use the maximum heating or
sible. The system will adjust the temper- changed. In this way, the functions will maximum cooling functions:
ature, the quantity and the distribution of switch from automatic to manual control
the air introduced into the passenger com- ❒ HI function (maximum heating):
until AUTO is pressed again. With on or
partment and will manage the recircula- select by turning the temperature knob
LIGHTS AND
more manually set functions, the intro-
MESSAGES
WARNING
tion function and the compressor. duced air temperature is still managed au- clockwise over the maximum value
Manual intervention is only required for tomatically by the system, except for when (32 °C).
the following functions during fully auto- the compressor is off: in the case, the air This function may be used to heat up the
matic operation. introduced into the passenger compart- passenger compartment exploiting the
EMERGENCY
ment cannot be cooler than the outside
IN AN
❒ T air recirculation, to keep the system potential to the maximum. In this
air. condition, the system stop controlling
function always either on or off;
temperature automatically and sets air
❒ Z to speed up demisting/defrosting of mixing to maximum heating. The air speed
SPECIFICATIONS MAINTENANCE
windscreen, rear window and exter- and distribution are fixed.
CAR
nal rearview mirrors;
Specifically, if the heating fluid is not suffi-
ciently warm, the fan will not start up at
the maximum speed immediately to limit
introducing excessively cool air into the
TECHNICAL
passenger compartment.
All manual settings will be allowed when
this function is on.
INDEX
61
044-090 LINEA 1ed GB 3-09-2008 17:29 Pagina 62
anticlockwise under the minimum value frost them. adequately cool (summer).
(16 °C). ▲ Air flow distributed between wind-
˙ Air flow at central and side dashboard
This function may be used to cool down vents to ventilate the chest and the ˙ screen and front side window de-
▼ froster/demister and central and side
CORRECT USE
the passenger compartment exploiting the face during the hot season.
OF THE CAR
system potential to the maximum. In this dashboard vents. This distribution al-
condition, the system stop controlling ▼ Air flow to the front and rear foot well lows adequate air diffusion and main-
temperature automatically and sets air vents. Thanks to the natural tenden- tains a good level of comfort both in
mixing to maximum cooling. The air speed cy of hot air to spread upwards, this summer and winter.
distribution pattern allows to warm
LIGHTS AND
MESSAGES
WARNING
and distribution are fixed. All manual set- The set distribution is shown by the cor-
tings will be allowed when this function the passenger compartment up as
quickly as possible, providing an im- responding LEDs on the selected buttons.
is on.
mediate feeling of warmth. To restore automatic air distribution con-
To switch the function off, simply turn the
˙ Air flow distributed between foot well trol after a manual adjustment, press but-
EMERGENCY
temperature knob anticlockwise and set ▼ vents (hotter air) and central and side ton AUTO.
IN AN
62
044-090 LINEA 1ed GB 3-09-2008 17:29 Pagina 63
AND CONTROLS
Fan speed adjusting buttons (H) AUTO (A) (automatic operation) Air recirculation on/off button (G)
DASHBOARD
Press button H to increase or to decrease Press AUTO to make the system auto- Air recirculation works according to the
the fan speed and therefore the amount matically adjust the quantity and distribu- following operating logics:
of air admitted into the passenger com- tion of the air introduced into the pas-
partment, although keeping the required senger compartment. All previous manu- ❒ override on (inside air recirculation
temperature set. al settings will be cancelled. always on), indicated by the the LED
DEVICES
SAFETY
on button G and symbol T on
The fan speed is shown by the lit bars on The message FULL AUTO will appear the display;
the display: on the front display in this condition.
❒ override off (air recirculation always
❒ max fan speed = all bars lit;
CORRECT USE
By manually intervening on at least of the off and introduction of external air),
OF THE CAR
functions automatically managed by the indicated by the fact that the LED on
❒ min fan speed = one bar lit. system (air recirculation, fan speed or the button is off ê is on the display.
The fan can be cut off only if the climate compressor on/off), the word FULL will
disappear from the display indicating that These operating conditions are obtained
control compressor has been switched by pressing G in sequence.
LIGHTS AND
MESSAGES
WARNING
off pressing button F-fig. 40. the system is no longer automatically con-
trolling all the functions (the temperature IMPORTANT The inside air recircula-
IMPORTANT To restore automatic fan will still be controlled automatically by the tion system makes it possible to reach
speed control after a manual adjustment, system). the required heating or cooling condi-
press button AUTO. tions faster.
EMERGENCY
IMPORTANT Should the system (after
IN AN
IMPORTANT At high speeds, the dynamic manual settings) be no longer able to It is however inadvisable to use it on
effect may increase the flow of air into the guarantee the required temperature set rainy/cold days as it would considerably
passenger compartment which in this case in the passenger compartment, the set increase the possibility of the windows
will not directly correspond to the fan temperature value will start flashing to in- misting inside, especially if the climate
SPECIFICATIONS MAINTENANCE
speed bar display. dicate this condition, after one minute the control compressor is off.
CAR
AUTO message will turn off.
Recirculation is forced off (i.e. air is
To restore system automatic control at introduced from the outside) when the
any time, after one or more manual ad- the outside temperature is cold to pre-
TECHNICAL
justments, press button AUTO. vent misting up.
It is advisable not to use the air recircu-
lation function when the outside tem-
perature is low to prevent the windows
from rapidly misting up.
INDEX
63
044-090 LINEA 1ed GB 3-09-2008 17:29 Pagina 64
AND CONTROLS
DASHBOARD Climate control compressor IMPORTANT With the compressor off, Fast window demisting/defrosting
enabling button (F) it is not possible to introduced air cooler button (D)
than ambient temperature into the pas-
Press √ to switch the climate control senger compartment. Furthermore, in Press this button: the climate control sys-
compressor off (if on). The icon on the certain conditions, the windows could tem will automatically switch on all the
display will go out. mist up rapidly because the air is not de- functions required for fast windscreen and
front side window demisting/defrosting,
DEVICES
The system will switch recirculation off press √ again (in this case, the system will able;
when the compressor is switched off to only work as a heater) or press AUTO. ❒ air recirculation off;
prevent misting up. Although the system
is capable of maintaining the required tem- With climate control compressor off, the ❒ maximum air temperature HI on both
fan speed can be set to zero manually (no areas;
LIGHTS AND
shown).
IN AN
64
044-090 LINEA 1ed GB 3-09-2008 17:29 Pagina 65
AND CONTROLS
IMPORTANT The quick demisting/de- Switching the system off (E) Press AUTO to switch the automatic cli-
DASHBOARD
frosting function will stay on for approxi- mate control system back on.
mately 3 minutes after the engine coolant Press E to switch the climate control sys-
temperature is warm enough to ensure tem off. The display will go out as a con-
rapid window demisting. sequence.
When the function is on, the LED on the The following climate control conditions
DEVICES
SAFETY
rear window demister button will light up will be established when the system is off:
and the message FULL AUTO will go ❒ display off;
out on the display.
❒ temperature not shown;
CORRECT USE
OF THE CAR
You may only adjust the fan speed and
switch the rear window demister off man- ❒ air recirculation on, passenger com-
ually when this function is running. partment isolated from the outside
(recirculation LED on);
To restore running operations before this
❒ climate control compressor off;
LIGHTS AND
MESSAGES
WARNING
function was activated, press either but-
ton B, air recirculation button G, com- ❒ fan off.
pressor button F or button AUTO A.
EMERGENCY
IN AN
SPECIFICATIONS MAINTENANCE
TECHNICAL
INDEX CAR
65
044-090 LINEA 1ed GB 3-09-2008 17:29 Pagina 66
AND CONTROLS
DASHBOARD
EXTERNAL LIGHTS
The left-hand stalk fig. 44/a operates
most of the external lights.
The external lights can only be switched
DEVICES
SAFETY
F0R0037m F0R0238m
fig. 44/a fig. 44/b
LIGHTS OFF
MAIN BEAM HEADLIGHTS AUTOMATIC HEADLIGHT
Knurled ring turned to symbol O. SENSOR (day light sensor)
When the knurled ring is at 2, pull the
LIGHTS AND
To turn the main beams off, pull again the the lights on. The sensitivity of the day light
lever towards the steering wheel (dipped sensor may be adjusted by means of the
DIPPED BEAM HEADLIGHTS beams will turn on again). “Setup menu” on the instrument panel.
Turn the knurled ring to 2.
SPECIFICATIONS MAINTENANCE
cluster will come on at the same time. Pull the stalk towards the steering wheel Turn the knurled ring to 2
A . the side/tail-
(1st unstable position) regardless of the po- lights and dipped beam headlights are
sition of the knurled ring. The warning switched on automatically according to
TECHNICAL
66
044-090 LINEA 1ed GB 3-09-2008 17:29 Pagina 67
AND CONTROLS
Deactivation Warning light 3 on the instrument pan-
DASHBOARD
el will light up and the corresponding mes-
The main beam headlights will go out fol- sage will appear on the display (see
lowed after approximately 10 seconds by “Warning lights and messages”) as long as
the side/taillights when the sensor is de- the function is on. The warning light will
activated. go out when the lever is operate and stay
DEVICES
SAFETY
The sensor cannot detect the presence of on until the function is automatically de-
fog: switch the lights on manually in this activated. Time for which the lights stay
case. on can only be increased by operating the
lever.
CORRECT USE
OF THE CAR
F0R0038m
DIRECTION INDICATORS fig. 45 fig. 45
Deactivation
Push the stalk to (stable) position: “FOLLOW ME HOME” DEVICE
Keep the stalk pulled towards the steer-
❒ up (position 1): right-hand indicator; This function allows the illumination of the ing wheel for more than 2 seconds.
LIGHTS AND
MESSAGES
WARNING
❒ down (position 2): left-hand indicator; space in front of the car for a preset pe-
riod of time.
Warning light Î or ¥ will blink on the in-
strument panel. Activation
EMERGENCY
Indicators are switched off automatically With the ignition key at STOP or re-
IN AN
when the steering wheel is straightened. moved, pull the left-hand stalk towards the
If you want the indicator to flash briefly to steering wheel within 2 minutes from
show that you are about to change lane, when the engine is turned off.
SPECIFICATIONS MAINTENANCE
move the stalk up or down without click- At each single movement of the stalk, the
ing into position (unstable position). When
CAR
lights will remain on for an extra 30 sec-
released the stalk will return to its home onds up to a maximum of 210 seconds;
position. then the lights are switched off automati-
cally.
TECHNICAL
INDEX
67
044-090 LINEA 1ed GB 3-09-2008 17:29 Pagina 68
AND CONTROLS
DASHBOARD
WINDOW WASHING IMPORTANT Replace wiper blades as
specified in section “Car maintenance”.
The right stalk fig. 46 controls windscreen
wiper/washer operation.
F0R0039m
fig. 46 excessive stress and the motor protec-
The stalk ring nut can be moved to four
different positions: tion which prevents operation for a few
With the ring in position ≤ the wind- seconds may trip. If operation is not re-
O windscreen wiper off; screen wiper will automatically adapt to stored, even after turning the key and
the speed of the car. restarting the engine, go to a Fiat Deal-
LIGHTS AND
≤ intermittent;
MESSAGES
WARNING
ership.
≥ continuous slow;
¥ continuous fast.
EMERGENCY
68
044-090 LINEA 1ed GB 3-09-2008 17:29 Pagina 69
AND CONTROLS
“Smart washing” function RAIN SENSOR Deactivation
DASHBOARD
Pull the stalk towards the steering wheel (where provided) Change the stalk knurled ring position
(unstable position) to operate the wind- The rain sensor is located behind the dri- from ≤ fig. 46 or turn the ignition key
screen washer. ving mirror in contact with the windscreen to STOP.
Keeping the stalk pulled for more than half and has the purpose of automatically ad- At the next start-up (key at MAR), the
just, during the intermittent operation, the
DEVICES
SAFETY
a second, with just one movement it is sensor will not be reactivated even if the
possible to operate the washer jet and the frequency of the windscreen wiper knurled ring is at ≤ fig. 46. To reacti-
wiper at the same time. strokes as to the rain intensity. vate the sensor, move the ring from po-
IMPORTANT Keep clean the glass in the sition ≤ to any other position and then
CORRECT USE
The wiper stops working three strokes af-
OF THE CAR
sensor area. return it to position ≤.
ter releasing the stalk.
Rain sensor activation will be indicated by
A further stroke after 6 seconds com- Activation at least one wiper “stroke” even if the
pletes the wiping operation. windscreen is dry.
Move the right-hand stalk knurled ring to
LIGHTS AND
MESSAGES
WARNING
≤ fig. 46. The rain sensor is able to recognize and
The activation of the rain sensor is sig- automatically adjust itself in the presence
nalled by a control acquisition “stroke”. of the following particular conditions:
❒ presence of dirt on the controlled sur-
EMERGENCY
Through the set up menu it is possible to
IN AN
increase the sensitivity of the rain sensor. face (salt, dirt, etc.);
The increase of the sensitivity of the rain ❒ difference between day and night.
sensor is signalled by a control and acqui- IMPORTANT Streaks of water may cause
SPECIFICATIONS MAINTENANCE
sition “stroke”. unnecessary blade moving.
CAR
Operating the windscreen washer with
the rain sensor activated the normal wash-
ing cycle is performed at the end of which
the rain sensor resumes its normal auto-
TECHNICAL
matic function.
INDEX
69
044-090 LINEA 1ed GB 3-09-2008 17:29 Pagina 70
AND CONTROLS
DASHBOARD
CRUISE CONTROL SWITCHING THE DEVICE ON
(constant speed Turn knob A-fig. 47 to ON.
regulator) The Cruise Control cannot be engaged
in first or reverse gear. It is advisable to
(where provided) engage it in 4th or higher gears.
DEVICES
SAFETY
It is a device able to support the driver, Travelling downhill with the device en-
with electronic control, which allows dri- gaged, the car speed may increase more
ving at speed over 30 km/h on long and than the memorised one.
CORRECT USE
F0R0041m
When the device is activated the warn- fig. 47
desired speed, without pressing the ac- ing light Ü turns on together with the rel-
celerator pedal. Therefore it is not sug- evant message on the instrument panel STORING THE CAR SPEED
gested to use this device on extra-urban (where provided).
roads with traffic. Do not use it in town. Proceed as follows:
LIGHTS AND
MESSAGES
WARNING
70
044-090 LINEA 1ed GB 3-09-2008 17:29 Pagina 71
AND CONTROLS
RESTORING STORED SPEED REDUCING THE STORED SPEED
DASHBOARD
case the system is not really switched
If the device has been disengaged for ex- The stored speed can be increased in two off but the request for acceleration
ample pressing the brake or clutch pedal, ways: takes priority over the system. The
the memorised speed can be reset as fol-
lows: ❒ by switching the device off and then cruise control is however active and it
storing a new speed; will not be necessary to press button
DEVICES
SAFETY
❒ accelerate gradually until reaching a RES B-fig. 47 to resume previous con-
speed approaching the one stored; or ditions after ending acceleration.
❒ engage the gear selected at the time ❒ by moving the stalk downwards (–) un- The device is automatically switched off in
til reaching the new speed which will be one of the following cases:
CORRECT USE
when the speed was originally stored;
OF THE CAR
stored automatically.
❒ press RES B-fig. 47. ❒ if the ABS or ESP systems cut-in;
Each operation of the stalk will corre-
spond to a slight reduction in speed (about ❒ with car speed below the preset limit;
INCREASING THE STORED 1 km/h), while keeping the stalk down- ❒ in the case of system failure.
LIGHTS AND
MESSAGES
WARNING
SPEED wards will correspond to a continuous
speed reduction.
The stored speed can be increased in two
ways:
SWITCHING THE DEVICE OFF WARNING
❒ by pressing the accelerator and then
EMERGENCY
The device can be switch off in the fol- When travelling with the de-
IN AN
storing the new speed reached;
lowing ways: vice on, never set the
or gearshift lever to neutral.
❒ by turning knob A to OFF;
❒ by moving the stalk upwards (+).
SPECIFICATIONS MAINTENANCE
❒ by turning the engine off;
Each operation of the stalk will corre-
CAR
spond to a slight increase in speed (about ❒ by pressing the brake pedal;
1 km/h), while keeping the stalk upwards WARNING
❒ by pressing the clutch pedal;
will correspond to a continuous speed in- In the event of device faults
TECHNICAL
crease. or failures, turn knob A to
OFF and contact a Fiat Dealership.
INDEX
71
044-090 LINEA 1ed GB 3-09-2008 17:29 Pagina 72
AND CONTROLS
DASHBOARD
CEILING LIGHTS
F0R0043m F0R0042m
fig. 48/a fig. 49
C and D will turn on/off when opening/
closing the front doors.
FRONT CEILING LIGHT WITH
With switch A pressed on the left side, MOVABLE LENS
lights C and D will always stay off. With
LIGHTS AND
MESSAGES
WARNING
switch A pressed on the right side, lights The light will turn on/off by pressing the
C and D will always stay on. movable lens rightwards or leftwards as
shown in fig. 49.
Light turning on/off is gradual.
EMERGENCY
72
044-090 LINEA 1ed GB 3-09-2008 17:29 Pagina 73
AND CONTROLS
Ceiling light timing LIGHT TIMING WHEN GETTING INTO THE CAR LIGHT TIMING WHEN GETTING OUT
DASHBOARD
OF THE CAR
On certain versions to facilitate getting Lights will turn on as follows:
in/out of the car at night or with poor After removing the key from the ignition
lighting, 2 different timed switching on ❒ for about 10 seconds when opening switch, the ceiling lights will turn on as fol-
modes have been provided. front doors; lows:
❒ for about 3 minutes when opening one
DEVICES
SAFETY
❒ within 2 minutes from turning the en-
of the side doors; gine off for about 10 seconds;
❒ for about 10 seconds when closing the ❒ when opening one of the side doors for
doors.
CORRECT USE
about 3 minutes;
OF THE CAR
Timing will stop when turning the ignition ❒ when closing one of the doors for
key to MAR. about 10 seconds.
Timing will stop automatically when lock-
LIGHTS AND
MESSAGES
WARNING
ing the doors.
EMERGENCY
IN AN
SPECIFICATIONS MAINTENANCE
TECHNICAL
INDEX CAR
73
044-090 LINEA 1ed GB 3-09-2008 17:29 Pagina 74
AND CONTROLS
DASHBOARD
A
B
DEVICES
SAFETY
B
CORRECT USE
OF THE CAR
For versions fitted with boot light, it will These lights A are located in the doors Lights B by the side of the courtesy mir-
turn on automatically when opening the and they will turn on when opening the ror will light up when cover A on the sun
tailgate and it will turn off at closing. relevant door, regardless of the ignition visor on driver’s or passenger’s side is
key position. raised with the key at MAR. The lights al-
EMERGENCY
74
044-090 LINEA 1ed GB 3-09-2008 17:29 Pagina 75
CONTROLS
AND CONTROLS
DASHBOARD
HAZARD LIGHTS fig. 55
They turn on by pressing switch A, re-
gardless of the position of the ignition key.
DEVICES
SAFETY
When the device is on, the switch is flash-
ing and warning lights Î e ¥ on the pan-
el come blink.
CORRECT USE
OF THE CAR
F0R0305m F0R0047m
fig. 54 fig. 55
Press the switch again to turn the lights
off.
ODDMENTS COMPARTMENT
COURTESY LIGHT The use of hazard lights is governed by the
Highway Code of the country you are in.
LIGHTS AND
(where provided) fig. 54
MESSAGES
WARNING
Keep to the rules.
On versions where it is fitted, the light
comes on automatically when the com-
partment is opened and goes out when it
EMERGENCY
is closed.
IN AN
F0R0048m
fig. 56
SPECIFICATIONS MAINTENANCE
FRONT FOG LIGHTS
CAR
(where provided) fig. 56
To turn front fog lights on, press button
5, to activate these lights it is necessary
TECHNICAL
to have the side/taillights switched on.
The warning light 5 on the instrument
cluster will come on at the same time.
Press the button again to turn the lights off.
INDEX
The use of fog lights is governed by the
Highway Code of the country you are in.
Keep to the rules.
75
044-090 LINEA 1ed GB 3-09-2008 17:29 Pagina 76
AND CONTROLS
DASHBOARD
DEVICES
SAFETY
CORRECT USE
OF THE CAR
providing the dipped beam headlights or nition key at STOP or removed, by mov-
ing the left stalk knurled ring first to O and To close: close the door and press lever
the front fog lights (where provided) are A. Also the rear doors will be locked in
switched on. then to position 6 or 2.
this way (centralised door locking system).
The warning light 4 on the instrument The warning light 3 on the instrument
Warning light ´ will light up with the cor-
EMERGENCY
panel will light up. panel will come on at the same time.
IN AN
Highway Code of the country you are in. Press button A to switch the device on.
Keep to the rules. The device will be switched off automati-
cally after approximately 20 minutes.
TECHNICAL
INDEX
76
044-090 LINEA 1ed GB 3-09-2008 17:29 Pagina 77
AND CONTROLS
The message “FPS on” will appear on the Door unlocking in the event
DASHBOARD
digital display when the switch trips. The of a crash
The car is fitted with a safety switch that message “Inertia switch tripped. See hand-
book” will appear on the multifunctional If the fuel cut-off switch trips following an
in the event of a crash comes into opera- accident, the doors will be automatically
tion by cutting off fuel and turning off the display.
unlocked to let you leave the car and the
engine as a consequence. ceiling lights will be switched on at the
DEVICES
SAFETY
This device therefore prevents fuel leaks same time. The doors can always be
due to fuel piping breaking. opened from the inside of the car by
WARNING means of the specific levers.
IMPORTANT After the accident, re- If, after a crash, you smell fu-
CORRECT USE
OF THE CAR
member to remove the electronic key el or see leaks from the fuel Proceed as follows if no fuel leakage is
from the ignition device to prevent drain- system, do not reset the switch to found and and the car is in condition to be
ing the battery. avoid fine risk. driven to rearm the fuel cut-off switch.
LIGHTS AND
MESSAGES
WARNING
WARNING
If the centralised door lock-
ing system was operated
EMERGENCY
from inside the car and the fuel cut-
IN AN
off switch did not manage to auto-
matically release the doors, it will not
be possible to access the passenger
SPECIFICATIONS MAINTENANCE
compartment from the outside after
an accident. The possibility of open-
CAR
ing the doors from the outside de-
pends on the conditions of the doors
themselves after the accident: if may
not be possible to open a damaged
TECHNICAL
door. In this case, try to open the oth-
er doors of the car.
INDEX
77
044-090 LINEA 1ed GB 3-09-2008 17:29 Pagina 78
AND CONTROLS
DASHBOARD
INTERIOR FITTINGS
F0R0208m F0R0104m
fig. 60 fig. 61
62 to keep documents.
Re-arming the fuel cut-off switch When the oddment compartment is
opened, an interior courtesy light comes
on.
LIGHTS AND
MESSAGES
WARNING
WARNING
ODDMENT COMPARTMENTS
Before resetting the fuel cut-
off switch carefully inspect Oddment compartment A-fig. 63, is lo-
EMERGENCY
the car for fuel leaks. cated on the dashboard, on the left of the
IN AN
steering wheel.
F0R0077m
fig. 62
SPECIFICATIONS MAINTENANCE
F0R0078m
fig. 63
78
044-090 LINEA 1ed GB 3-09-2008 17:29 Pagina 79
AND CONTROLS
DASHBOARD
DEVICES
SAFETY
CORRECT USE
OF THE CAR
F0R0053m F0R0055m F0R0057m
fig. 64 fig. 66 fig. 68
LIGHTS AND
(where provided)
MESSAGES
WARNING
Certain versions are fitted with armrest
A-fig. 67 between the front seats.
To use it, push it down as shown in
EMERGENCY
fig. 68.
IN AN
Press button A-fig. 68 to raise the up-
fig. 65 F0R0054m
fig. 67 F0R0056m
per part of the arm rest and access com-
partment B. Operate lever C to move the
SPECIFICATIONS MAINTENANCE
Oddment compartment B-fig. 64 is lo- DOOR POCKETS fig. 66 armrest down with respect to the posi-
CAR
cated in the middle of the dashboard. tion of normal use.
Paper/map pockets are located in door
panels.
CENTRAL CONSOLE ODDMENT
TECHNICAL
COMPARTMENT
The compartiment A-fig. 65 is located on
the dashboard central zone.
INDEX
79
044-090 LINEA 1ed GB 3-09-2008 17:29 Pagina 80
AND CONTROLS
DASHBOARD
DEVICES
SAFETY
CORRECT USE
OF THE CAR
keep telephone cards CD holders and It is located on the central console in front
magnetic cards. of the handbrake.
Press button A to switch on the cigar
lighter with ignition key at MAR.
EMERGENCY
IN AN
fig. 69-70
There are cup holders on the central tun-
nel (two cup holders in front of the gear-
TECHNICAL
80
044-090 LINEA 1ed GB 3-09-2008 17:29 Pagina 81
AND CONTROLS
DASHBOARD
DEVICES
SAFETY
CORRECT USE
OF THE CAR
F0R0062m F0R0064m F0R0065m
fig. 73 fig. 75 fig. 76
LIGHTS AND
MESSAGES
WARNING
ternal rearview mirror. They may be ori- cated on the back of the seat backrest
ented frontally and to the side. fig. 76.
A courtesy mirror can be applied to the
back of sun visors.
EMERGENCY
IN AN
On certain versions to use the mirror
(where provided) you shall open the slid-
fig. 74 F0R0063m ing cover A.
SPECIFICATIONS MAINTENANCE
A courtesy light may light up according
ASHTRAY (where provided) to the versions when the cover is opened.
CAR
fig. 73-74
The ashtray is a removable plastic box that
can be fitted into the glass/can recesses on
TECHNICAL
the central console.
IMPORTANT Do not use the box as an
ashtray and a waste paper basket at the
same time: it might set on fire in contact
INDEX
with cigarette stubs.
81
044-090 LINEA 1ed GB 3-09-2008 17:29 Pagina 82
AND CONTROLS
DASHBOARD
DOORS
CENTRAL DOOR
LOCKING/UNLOCKING SYSTEM
DEVICES
SAFETY
locked. The doors will be locked only if all Press lever A-fig. 79 to unlock all doors.
doors are closed. If one or more doors Pull the lever to unlock all doors. A LED
are open, the indication indicators and the on the driver’s door will indicate the state
LED on the driver’s door will flash in rapid (doors locked or unlocked). The LED is
sequence for approximately 3 seconds if on when the doors are locked and off
EMERGENCY
the direction indicators (if locked by press- flashing or fit the metal insert into the dri- “Multifunction display” in this section).
ing Á fig. 77 only) and the LED on the ver’s door lock and turn it anticlockwise.
driver’s door will flash rapidly for ap-
proximately 3 seconds.
INDEX
82
044-090 LINEA 1ed GB 3-09-2008 17:29 Pagina 83
WINDOW WINDERS
AND CONTROLS
DASHBOARD
POWER WINDOWS
The driver’s door armrest features two
fig. 82 or (where provided) five fig. 81
DEVICES
SAFETY
switches that with key at MAR shall be
used:
A to open/close the left front window;
CORRECT USE
OF THE CAR
F0R0068m F0R0200m
fig. 80 fig. 81
B to open/close the right front window;
CHILD LOCK fig. 80 C to open/close the left rear window
(where provided);
This device prevents opening the rear
LIGHTS AND
MESSAGES
WARNING
doors from the inside. This device can be D to open/close the right rear window
engaged only with rear doors open. (where provided);
❒ position 1 - device engaged (door E to inhibit rear door controls (where
locked); provided).
EMERGENCY
❒ position 2 - device not engaged (door
IN AN
may be opened from the inside).
The device A-fig. 80 stays on even if the F0R0201m
fig. 82
doors are unlocked by the centralised
SPECIFICATIONS MAINTENANCE
system.
Automatic continuous operation
CAR
(where provided)
Power windows are equipped with an
WARNING up/down mechanism for the front driver
TECHNICAL
Always use this device when side window and of a mechanism just for
transporting children. After the down movement of the other win-
engaging the child lock on both rear dows.
doors, check for proper engagement
by trying to open a rear door with the
INDEX
internal handle.
83
044-090 LINEA 1ed GB 3-09-2008 17:29 Pagina 84
AND CONTROLS
DASHBOARD Hold one of the buttons pressed for IMPORTANT With ignition key at STOP WARNING
longer than half a second to operate the or removed, the power windows remain
automatic continuous window operation activated for about 2 minutes and are de- The system conforms to
function. The window will stop when its activated immediately the moment a door the forthcoming standard
reached end of travel or when the but- is opened. 2000/4/EC concerning the safety of
ton is pressed again. passengers leaning out of the pas-
senger compartment.
DEVICES
SAFETY
CORRECT USE
OF THE CAR
EMERGENCY
IN AN
SPECIFICATIONS MAINTENANCE
TECHNICAL CAR
INDEX
84
044-090 LINEA 1ed GB 3-09-2008 17:29 Pagina 85
AND CONTROLS
WARNING
DASHBOARD
Incorrect use of the power
windows may be dangerous.
Before operation, always check that
no-one is exposed to the risk of being
injured by directly by the moving win-
DEVICES
SAFETY
dow or objects getting caught and
dragged. When leaving the car, al-
ways remove the key from the igni-
CORRECT USE
tion device to avoid the risk of injury
OF THE CAR
F0R0069m F0R0070m
fig. 83 fig. 85
due to accidental operation of the
power windows.
MANUAL REAR
(where provided) fig. 85
LIGHTS AND
MESSAGES
WARNING
To open and to close the window use the
Power window system initialisation relevant window winder.
Safety system shall be re-initialised after
disconnecting the battery or if the rele-
EMERGENCY
vant protection fuse is blown.
IN AN
Initialisation procedure:
F0R0000m
fig. 84
❒ fully close manually the window to ini-
SPECIFICATIONS MAINTENANCE
tialise;
Front and rear passenger door
CAR
windows (where provided) ❒ rafter the window has reached the up-
per end of travel, hold the up button
Front passenger door armrest and rear pressed for at least one second.
door armrests feature the switches A-
TECHNICAL
fig. 83 to be used for controlling the cor-
responding window.
Press button A-fig. 84 to inhibit rear door
controls (where provided).
INDEX
85
044-090 LINEA 1ed GB 3-09-2008 17:29 Pagina 86
AND CONTROLS
DASHBOARD
BOOT
F0R0071m F0R0072m
fig. 86 fig. 88
shock absorbers of the tailgate itself.
LIGHTS AND
B
MESSAGES
WARNING
WARNING
Never exceed the maximum
allowed load in the boot (see
“Technical Specifications”). Make
EMERGENCY
BOOT CLOSING
CAR
the rear window shelf: they inserting and turning the metallic insert of battery is flat), release the boot lock by
cause cause injury to passengers in the key in the boot lock anticlockwise as turn the key in clockwise.
the event of an accident or sudden shown in fig. 88. The boot lock can be re-
braking. leased from inside the vehicle operating
on lever A-fig.87 located on driver side
INDEX
86
044-090 LINEA 1ed GB 3-09-2008 17:29 Pagina 87
AND CONTROLS
EXTENDING THE BOOT The boot extension to the right makes it
DASHBOARD
possible to carry two passengers on the
Partial extension (where provided) rear seat left-hand side.
(1/3 or 2/3) fig. 91 The boot extension to the left makes it
The boot can be partially (1/3 or 2/3) or possible to carry one passenger on the
rear seat right-hand side.
DEVICES
SAFETY
totally extended splitting the rear seat.
Proceed as follows:
❒ tip the cushions forward;
CORRECT USE
OF THE CAR
F0R0075m
fig. 90
LIGHTS AND
MESSAGES
WARNING
EMERGENCY
IN AN
F0R0076m
fig. 91
SPECIFICATIONS MAINTENANCE
❒ pull the two locking devices A-fig. 90
CAR
upwards to unlock respectively the left
or right section of the backrest and
then guide the backrest onto the cush-
TECHNICAL
ion.
INDEX
87
044-090 LINEA 1ed GB 3-09-2008 17:29 Pagina 88
AND CONTROLS
DASHBOARD
BONNET
arrow;
❒ operate lever A-fig. 95 as shown in the
figure;
CORRECT USE
OF THE CAR
F0R0077m F0R0078m
fig. 92 fig. 93
❒ lift the bonnet and at the same time re-
Maximum extension fig. 92 To return the rear seat back to its lease the rod D-fig. 96 from the catch,
original position fig. 93 then fit end C-fig. 97 of the rod into
Tilt the rear seat completely to obtain the bonnet recess E.
LIGHTS AND
MESSAGES
WARNING
maximum boot extension. Lift the backrests and push them back un-
Proceed as follows: til your hear both fastening mechanisms
click and return the cushions to the nor-
❒ completely lower the rear seat head re- mal position of use.
straints;
EMERGENCY
❒ tip the cushions forward; to the position of use, make sure it is cor-
rectly fastened and you hear the lock click.
❒ pull the fastening devices A-fig. 90 up-
wards to release the backrests and fold
SPECIFICATIONS MAINTENANCE
WARNING
Make sure the backrest is
properly secured at both
TECHNICAL
88
044-090 LINEA 1ed GB 3-09-2008 17:29 Pagina 89
AND CONTROLS
DASHBOARD
DEVICES
SAFETY
CORRECT USE
OF THE CAR
F0R0080m F0R0079m F0R0081m
fig. 94 fig. 95 fig. 96
LIGHTS AND
MESSAGES
WARNING
❒ hold the bonnet up with one hand and
with the other remove rod C-fig. 97
from seat E and fit it back into its catch
D-fig. 96;
EMERGENCY
IN AN
F0R0082m
fig. 97
SPECIFICATIONS MAINTENANCE
❒ lower the bonnet to approximately 20
CAR
centimetres from the engine compart-
ment and let it drop. Make sure that the
bonnet is completely closed and not
only fastened by the safety catch by try-
TECHNICAL
ing to open it. If it is not perfectly
closed, open the bonnet and repeat the
procedure. No not simply press it.
IMPORTANT Always check that the bon-
INDEX
net is closed properly to avoid its opening
while the car is travelling.
89
044-090 LINEA 1ed GB 3-09-2008 17:29 Pagina 90
AND CONTROLS
DASHBOARD
WARNING ROOF RACK/SKI RACK
The bonnet must always be
perfectly closed while trav- Front couplings are set at points A-fig. 98.
elling for reasons of safety. Make sure Front couplings are set at points B.
that the bonnet is perfectly closed
and that the lock is engaged. If you
DEVICES
SAFETY
correct manner.
OF THE CAR
F0R0217m
fastening screws are correct- fig. 98
ly positioned after a few kilometres.
IMPORTANT Follow the instructions
contained in the assembly kit to the letter.
WARNING Assembly must be performed by qualified
LIGHTS AND
MESSAGES
WARNING
WARNING
IN AN
only.
90
091-102 LINEA 1ed GB 3-09-2008 17:29 Pagina 91
HEADLIGHTS
AND CONTROLS
Aiming the headlights fig. 99
DASHBOARD
Press Ò and on the control panel.
BEAM DIRECTION The display located on the instrument pan-
Correction direction of the headlights is el, provides the visual indication of the po-
essentially for the comfort and safety of sitions during the adjustment operation.
DEVICES
SAFETY
the driver and the other road users. The Position 0 - one or two passengers on
headlights must be correctly directed to front seats.
ensure the best visibility conditions when
the headlights are on. Contact Fiat Deal- Position 1 - five passengers.
CORRECT USE
OF THE CAR
F0R0083m
fig. 99
ership to have the headlights properly ad- Position 2 - five passengers + load in the
justed. boot.
HEADLIGHT AIMING DEVICE
This device works with the key at MAR Position 3 - driver + maximum admitted
load in the boot.
LIGHTS AND
MESSAGES
WARNING
and the dipped beam headlights on. The
car will slant backwards when it is loaded, IMPORTANT Check beam aiming every
raising the light beam. The beams must time the load carried changes.
therefore be directed again in this case.
EMERGENCY
AIMING THE FRONT FOG
IN AN
LIGHTS (where provided)
Contact Fiat Dealership to have the head-
lights properly adjusted.
SPECIFICATIONS MAINTENANCE
TECHNICAL
INDEX CAR
91
091-102 LINEA 1ed GB 3-09-2008 17:29 Pagina 92
AND CONTROLS
DASHBOARD
ABS SYSTEM WARNING FAILURE INDICATIONS
The ABS exploits the tyre-
If you have never driven a car with ABS be- road grip at the best, but it ABS failure
fore, it is advisable to perform a few tests cannot improve it; you should there-
on slippery ground, naturally in conditions ABS failure is indicated by the turning on
of safety and respecting the Highway Code
fore take every care when driving on of warning light > on the instrument pan-
slippery surfaces without taking un-
DEVICES
this time, avoid sudden, repeated and pro- proaching the grip limit between tyres
CAR
92
091-102 LINEA 1ed GB 3-09-2008 17:29 Pagina 93
ESP SYSTEM
AND CONTROLS
EBD failure BRAKE ASSIST
DASHBOARD
(integrated ESP emergency
ABS failure is indicated by the turning on
braking assistance)
(Electronic Stability
warning lights > and x on the instru-
ment panel together with the dedicated (where provided) Program)
message on the multifunctional display This system (which cannot be deactivat- (where provided)
(where provided), (see section “Warning
DEVICES
SAFETY
ed) recognises emergency braking condi-
lights and messages”). tions according to the speed of operation The ESP system is an electronic system
In this case, the rear wheels may sudden- of the brake pedal and provides an addi- controlling the car stability in the event of
ly lock and the car may swerve. Drive tional hydraulic braking pressure to sup- tyre grip loss.
CORRECT USE
OF THE CAR
carefully to the nearest Fiat Dealership to port that provided by the driver. This al- The ESP system is therefore particularly
have the system checked. lows faster and more power operation of useful when grip conditions of the road sur-
the braking system. faces changes.
Brake Assist is deactivated on the versions In addition to the ESP system, ASR system
LIGHTS AND
equipped with ESP, in the event of ESP sys-
MESSAGES
WARNING
and Hill Holder, (where provided) also the
WARNING tem failure (indicated by warning light á MSR system (adjusting the engine braking
If warning light x only lights switching on together with the message torque) and the HBA system (improving
up on the instrument panel on the multifunctional display, where pro- the braking force during emergency brak-
(with a message on the multifunc- vided). ing) are provided.
EMERGENCY
tional display, where provided), stop
IN AN
the car immediate and go to the ABS SYSTEM INTERVENTION
nearest Fiat Dealership. Leakage of
hydraulic fluid from the braking sys- WARNING It is signalled by the blinking of the warn-
SPECIFICATIONS MAINTENANCE
tem will compromise functionality of When the ABS cuts in, and ing light á on the instrument panel, to
the braking system, either of the con- you feel the brake pedal pul- inform the driver that the car is in criti-
CAR
ventional type or with ABS. sating, do not remove your foot, but cal stability and grip conditions.
keep it pressed; in doing so you will
stop in the shortest amount of space
TECHNICAL
possible under the current road con-
ditions.
INDEX
93
091-102 LINEA 1ed GB 3-09-2008 17:29 Pagina 94
AND CONTROLS
DASHBOARD ESP SYSTEM ACTIVATION HILL HOLDER SYSTEM Failure indications
The ESP system is automatically activat- This system is an integral part of the ESP Warning light è on the instrument pan-
ed when the car is started and cannot be system and it is provided to facilitate start- el will light up in the event of a failure (see
de-activated. ing on slopes. “Warning lights and messages”).
It will activate automatically with the fol- IMPORTANT The Hill Holder system is
DEVICES
FAILURE INDICATIONS
SAFETY
el along with a message on the multifunc- gearbox to neutral or engaged gear oth-
tional display (where provided) (see er than reverse.
“Warning lights and messages”). The LED
on the ASR OFF button will light up. Con- ❒ downhill: car at a standstill on a road WARNING
tact Fiat Dealership as soon as possible. with a gradient higher than 5%, engine
LIGHTS AND
MESSAGES
running, clutch and brake pedal pressed ESP and ASR systems, the
and reverse gear engaged. tyres must absolutely be of the same
At pickup the ESP system control unit will brand and type on all wheels, in per-
WARNING keep brake force on wheels until reaching fect conditions and, above all, of
EMERGENCY
Do not take unnecessary the torque suitable for starting, or in any type, brand and size specified.
IN AN
risks, even if your cars fits an case for max. 2 seconds in order to pass
ESP system. Your driving style must easily from the brake pedal to the accel-
always be suited to the conditions of erator pedal.
SPECIFICATIONS MAINTENANCE
94
091-102 LINEA 1ed GB 3-09-2008 17:29 Pagina 95
AND CONTROLS
ASR SYSTEM (Antislip Regulator) WARNING A
DASHBOARD
The ASR function controls car drive and For correct operation of the
cuts in automatically every time one or ESP and ASR systems, the
both driving wheels slip. tyres must absolutely be of the same
According to slipping conditions, two dif- brand and type on all wheels, in per-
fect conditions and, above all, of
DEVICES
ASR
SAFETY
ferent control systems are activated: OFF
type, brand and size specified.
❒ if slipping involves both driving wheels,
the ASR function intervenes reducing
the power transmitted by the engine;
CORRECT USE
OF THE CAR
F0R0218m
fig. 100
❒ if the slipping involves only one driving MSR system
wheel, the ASR system cuts in auto- (engine braking torque control) When the ASR is switched off this is
matically braking the wheel that is slip- shown by the lighting up of the led on the
ping. It is an integral part of the ASR system that
button and by relevant message on the
LIGHTS AND
MESSAGES
WARNING
in case of sudden gear shifting, cuts in pro-
The action of the ASR is particularly help- viding torque to the engine thus prevent- multifunction display, where provided.
ful in the following circumstances: ing excessive driving wheel drive that, spe- If the ASR is switched off when travelling,
cially in poor grip conditions, can lead to it will turn on again automatically the next
❒ slipping of the inner wheel due to the time the engine is started.
loss of stability.
EMERGENCY
effect of dynamic load changes or ex-
IN AN
cessive acceleration; It may be useful to switch the ASR when
Switching the system on/off fig. 100 driving on snow-covered roads with snow
❒ too much power transmitted to the chains fitted: in these conditions, slipping
wheels also in relation to the conditions The ASR system switches on automatically
each time the engine is started. of the wheels during pick-up provides bet-
SPECIFICATIONS MAINTENANCE
of the road surface; ter traction.
CAR
When travelling, the ASR can be switched
❒ acceleration on slippery, snowy or off and on again pres100.
frozen surfaces;
❒ in the case of loss of grip on a wet sur-
TECHNICAL
face (aquaplaning).
INDEX
95
091-102 LINEA 1ed GB 3-09-2008 17:29 Pagina 96
AND CONTROLS
DASHBOARD
WARNING EOBD SYSTEM IMPORTANT After eliminating the in-
convenience, to check the system com-
Do not take unnecessary (where provided) pletely, Fiat Dealerships are obliged to run
risks, even if your cars fits a bench test and, if necessary, road tests
such a system. Your driving style must The EOBD system (European On Board which may also call for a long journey.
always be suited to the conditions of Diagnosis) allows continuous diagnosis of
the road, visibility and traffic. The dri-
DEVICES
el (together with relevant message on the light U either does not light
multifunctional display, where provided) up when the key is turned to
For correct operation of the ASR system, (see section “Warning lights and mes- MAR to if while travelling the warning
the tyres must absolutely be of the same sages”), when these conditions are no lights comes on either steady or blink-
brand and type on all wheels, in perfect longer in peak conditions. ing (along with a message on the mul-
LIGHTS AND
MESSAGES
WARNING
conditions and, above all, of type, brand tifunctional display, where provided).
and size specified. The objective is: The operation of warning light U may
❒ to monitor system efficiency; be checked by the traffic police using
FAILURE INDICATIONS specific devices. Follow the laws in
❒ warn when a fault causes emissions lev-
EMERGENCY
functional display (where provided) (see The system also has a diagnostic connec-
CAR
“Warning lights and messages”). In this tor that can be interfaced with appropri-
case, contact Fiat Dealership as soon as ate tools, which makes it possible to read
possible. the error codes stored in the control unit,
together with a series of specific parame-
TECHNICAL
96
091-102 LINEA 1ed GB 3-09-2008 17:29 Pagina 97
PARKING SENSORS
AND CONTROLS
Detection distances
DASHBOARD
(where provided) Central action radius 150 cm
Side action radius 60 cm
Parking sensors are located in the rear
bumper fig. 101 and their function is to If several obstacles are detected, the con-
DEVICES
inform the driver, through an intermittent trol unit indicates the nearest one.
SAFETY
buzzer, about the presence of obstacles
behind the car. FAILURE INDICATIONS
Parking sensor failures, if any, will be in-
CORRECT USE
OF THE CAR
F0R0084m
ACTIVATION fig. 101
dicated when engaging reverse by the
The sensors are automatically activated turning on of the instrument panel warn-
when the reverse gear is engaged. BUZZER WARNINGS ing light t together with the message on
When the reverse gear is engaged an in- the multifunction display, where provided
As the distance from the obstacle behind
LIGHTS AND
(see section “Warning lights and mes-
MESSAGES
WARNING
the car decreases, the acoustic alarm be- termittent acoustic signal is automatically
activated. sages”).
comes more frequent.
The acoustic signal:
❒ becomes louder as the reduction of dis-
EMERGENCY
IN AN
tance between the car and the obstacle
decreases;
❒ becomes continuous when the distance
SPECIFICATIONS MAINTENANCE
between the car and the obstacle is less
that 30 cm and stops immediately if the
CAR
distance increases;
❒ is constant if the distance is unvaried;
if this situation concerns the side sen-
TECHNICAL
sors, the buzzer will stop after about
3 seconds to avoid, for example, warn-
ing indications in the event of manoeu-
vres along walls.
INDEX
97
091-102 LINEA 1ed GB 3-09-2008 17:29 Pagina 98
AND CONTROLS
DASHBOARD OPERATION WITH TRAILER WARNING GENERAL WARNINGS
Parking sensor operation is deactivated au- The driver is always and on- ❒ When parking, take the utmost care to
tomatically when the trailer electric cable ly responsible for parking obstacles that may be set above or un-
plug is fitted into the car tow hook socket. and other dangerous manoeuvres. der the sensors.
Sensors are reactivated when removing Make sure that no-one is standing in ❒ Objects set close to the car, under cer-
the area, especially children or ani-
DEVICES
SAFETY
the trailer cable plug. tain circumstances are not detected and
mals. Parking sensors are designed to could therefore cause damages to the
In washing stations, clean sensors quickly assist drivers: in all cases, you must al- car or be damaged.
keeping the vapour jet/high pressure ways pay the utmost attention during
❒ Indications sent by the sensors can be
CORRECT USE
car.
The sensor must be clean
from mud, dirt, snow or ice in
order for the system to work.
EMERGENCY
poo if necessary.
TECHNICAL CAR
INDEX
98
091-102 LINEA 1ed GB 3-09-2008 17:29 Pagina 99
SOUND SYSTEM
AND CONTROLS
WARNING
DASHBOARD
(where provided) For connection to existing car
presetting system, contact
For the operation of the radio with Fiat Dealership to prevent any trouble
CD/MP3 CD (where provided), read the that could impair car safety.
DEVICES
instructions for use given in the Supple-
SAFETY
ment attached to the Owner Handbook.
CORRECT USE
OF THE CAR
F0R0085m
(where provided) fig. 102
The system consists of:
❒ sound system power wires Sound system installation
❒ front and rear speaker connecting The sound system shall be installed in the
LIGHTS AND
MESSAGES
WARNING
wires proper space occupied by the central
❒ aerial power wire oddment compartment, here you will find
the preset cables.
❒ 2 tweeters on front doors (30W max
power each); Lower the fasteners shown in fig. 102 to
EMERGENCY
❒ 2 mid-woofers on front doors (165 remove the box.
IN AN
mm diameter, 40W max power
each);
❒ 4/6 full-range speakers on rear doors
SPECIFICATIONS MAINTENANCE
and rear valance panels (130 mm
CAR
diameter, 40W max power each);
❒ radio aerial wire.
TECHNICAL
INDEX
99
091-102 LINEA 1ed GB 3-09-2008 17:29 Pagina 100
AND CONTROLS
DASHBOARD
ACCESSORIES ELECTRICAL/ELECTRONIC TRANSCEIVERS
DEVICE INSTALLATION AND MOBILE PHONES
PURCHASED BY THE
OWNER Electrical and electronic devices installed Radio transceiver equipment (e.g.: e-tacs
after buying the car by after-market ser- mobile phones, HAM radio systems and
vice must carry the following label: the like) shall not be used inside the car
If after buying the car, you decide to install unless a separate aerial is mounted on the
DEVICES
SAFETY
tact Fiat Dealership, whose qualified per- out separated aerial) produces radio-fre-
sonnel, besides suggesting the most suit- quency electromagnetic fields which, am-
able devices belonging to Lineaccessori Fi- Fiat Auto S.p.A. authorises the installation plified by the resonance effects inside the
at, will also evaluate the overall electric ab- of transceiving devices provided that they passenger compartment, may cause elec-
sorption, checking whether the car’s elec- trical systems equipping the car to mal-
LIGHTS AND
tric system is able to withstand the load gineering practice respecting the manu- function. This could compromise safety in
required, or whether it needs to be inte- facturer’s indications by a specialised cen- addition to constituting a potential hazard
grated with a more powerful battery. tre. for the passengers.
In addition, transmission and reception of
EMERGENCY
non-standard additional faults caused by the change or either di- the instructions for use provided by the
CAR
spoilers, light alloy wheels or wheel rectly or indirectly related to it. mobile phone’s manufacturer.
cups: they could reduce brake venti-
lation and consequently brake effi- Fiat Auto S.p.A. shall not be liable for dam-
ciency in the case of repeated, violent age caused by the installation of acces-
sories either not supplied or recom-
TECHNICAL
100
091-102 LINEA 1ed GB 3-09-2008 17:29 Pagina 101
AT THE FILLING
AND CONTROLS
DIESEL ENGINES
DASHBOARD
For diesel engines, use diesel
STATION If the outside temperature is very low, the fuel for motor vehicles com-
diesel thickens due to the formation of pliant with EN590 European
paraffin clots and could clog the diesel fu- specifications only. The use of
PETROL ENGINES el filter. other products or mixtures may dam-
age the engine beyond repair and con-
DEVICES
SAFETY
Use only unleaded petrol. In order to avoid these problems, differ- sequently cause lapse of warranty in
To avoid mistakes, the diameter of the fu- ent types of diesel are distributed ac- relation to the damage caused. If you
el filler is too small to introduce the beak cording to the season: summer type, win- accidentally introduce other types of
ter type and arctic type (cold, mountain fuel in the tank, do not start the engine
CORRECT USE
of a leaded petrol pump. The petrol oc-
OF THE CAR
tane rating (RON) must not be lower areas). and empty the tank. If the engine has
than 95. If refuelling with diesel fuel whose features run also for a very short time, you will
are not suitable to the temperature of use, need to have the entire fuel feed sys-
IMPORTANT An inefficient catalyst leads tem emptied in addition to the tank.
to harmful exhaust emissions, thus con- it is advisable to mix TUTELA DIESEL ART
LIGHTS AND
MESSAGES
WARNING
tributing to air pollution. additive in the proportions shown on the
container with the fuel. Pour the additive
IMPORTANT Never use leaded petrol, into the tank before the fuel.
even in small amount or in an emergency, Filling the tank
as this would damage the catalyst beyond When using or parking the car for a long
EMERGENCY
time in the mountains or cold areas, it is To fill the tank completely, top-up twice
repair.
IN AN
advisable to refuel using locally available after the pump switches off. Further top-
fuel. ups could cause faults in the fuel feeding
system.
In this case, it is also advisable to keep the
SPECIFICATIONS MAINTENANCE
tank over 50% full.
TECHNICAL
INDEX CAR
101
091-102 LINEA 1ed GB 3-09-2008 17:29 Pagina 102
AND CONTROLS
DASHBOARD
PROTECTING THE
ENVIRONMENT
The devices for curtailing petrol engine
emissions are the following:
DEVICES
SAFETY
F0M0203m F0R0210m
fig. 103 fig. 104
In addition, do not let the engine run, even
FUEL FILLER CAP fig. 103 When refuelling, position the cap on the for a test, with one or more spark plugs
device inside the lid as shown in fig. 103. disconnected.
To carry out fuelling, if your car fits a cen-
LIGHTS AND
MESSAGES
If your car does not fit a centralised lock- flames or lit sigarettes to the (E.G.R.).
IN AN
ing system, operate lever A-fig. 104 to fuel filler: fire risk. Keep your face
release the flap. away from the fuel filler to prevent
In some versions, cap B may be provided breathing in harmful vapours.
SPECIFICATIONS MAINTENANCE
to access the flap A-fig. 103, turn it an- The catalytic converter de-
ticlockwise and loosen the cap itself. velops high temperature dur-
The airtight closing may determine a slight ing operation. Do not park on grass,
increase of pressure in the tank. A suction dry leaves, pine needles or other flam-
TECHNICAL
noise when you release the cap is there- mable material: fire risk.
fore entirely normal.
INDEX
102
103-120 LINEA 1ed GB 3-09-2008 17:30 Pagina 103
SAFETY DEVICES
AND CONTROLS
DASHBOARD
SEAT BELTS ........................................................................... 104
S.B.R. SYSTEM ....................................................................... 105
DEVICES
SAFETY
PRETENSIONERS.................................................................. 106
CARRYING CHILDREN SAFELY...................................... 109
“UNIVERSAL ISOFIX” CHILD
CORRECT USE
OF THE CAR
RESTRAINT SYSTEM ASSEMBLY SETUP........................ 114
FRONT AIRBAGS................................................................. 115
SIDE AIRBAGS ...................................................................... 118
LIGHTS AND
MESSAGES
WARNING
EMERGENCY
IN AN
SPECIFICATIONS MAINTENANCE
TECHNICAL
INDEX CAR
103
103-120 LINEA 1ed GB 3-09-2008 17:30 Pagina 104
AND CONTROLS
DASHBOARD
SEAT BELTS B
A
USING THE SEAT BELTS fig. 1
The belt should be worn keeping the chest
straight and rested against the seat back.
DEVICES
SAFETY
F0R0150m F0R0151m
fig. 1 fig. 3
At removal, if it jams, let it rewind for a
short stretch, then pull it out again with-
out jerking. ADJUSTING THE FRONT SEAT
BELT HEIGHT
Press button C to release the belt. Ac-
LIGHTS AND
MESSAGES
WARNING
company the belt while it is being re- Always adjust the seat belt height to the
wound to prevent twisting. passenger’s body: this precaution may
considerably reduce the risk of injury in
Through the reel, the belt automatically the event of a collision.
adapts to the body of the passenger wear-
EMERGENCY
ing it, allowing freedom of movement. Correct regulation is obtained when the
IN AN
the belt if it is pulled and in the event of locking mechanism either up or down and
WARNING
CAR
sudden braking, collisions and on high at the same time move the ring B-fig. 3
speed bends. Never press button C-fig. 1 to the most suitable of the allowed posi-
when travelling. tions.
The rear seat is fitted with inertial seat
TECHNICAL
104
103-120 LINEA 1ed GB 3-09-2008 17:30 Pagina 105
AND CONTROLS
WARNING
DASHBOARD
correctly fastened when returning it to the
position of normal use after folding it. Remember that in the event
of a violent collision, back The car is fitted with the S.B.R. system
seat passengers not wearing seat belts (Seat Belt Reminder), consisting of a
also represent a serious danger for buzzer which, together with the turning
the front seat passengers. on of warning light < on the instrument
DEVICES
SAFETY
panel, warns the driver to fasten the seat
belt.
The buzzer can be deactivated (until the
CORRECT USE
OF THE CAR
next engine stop) as follows:
WARNING
Make sure the backrest is ❒ fasten the driver’s and passenger’s seat
properly secured at both belt;
sides to prevent it moves forward in ❒ turn the ignition key to MAR;
LIGHTS AND
MESSAGES
WARNING
the event of sharp braking causing in-
juries to passengers. ❒ wait for over 20 seconds and then re-
lease one of the seat belts.
For permanent deactivation, contact Fiat
EMERGENCY
Dealership.
IN AN
With digital display, the S.B.R. system can
only be reset at Fiat Dealership.
SPECIFICATIONS MAINTENANCE
TECHNICAL
INDEX CAR
105
103-120 LINEA 1ed GB 3-09-2008 17:30 Pagina 106
AND CONTROLS
DASHBOARD
PRETENSIONERS WARNING LOAD LIMITERS
The pretensioner can only To increase passenger’s safety, the front
To increase the efficiency of the seat belts, be used once. Go to a Fiat seat belt reels contain a load limiter which
the car is fitted with pretensioners. These Dealership to have it replaced after allows controlled sag in such a way as to
devices, in the event of a violent crash, is has been deployed. The expiration dose the force acting on the chest and
rewind the seat belts a few centimetres. date is shown on the label in the odd- shoulders during the belt restraining ac-
DEVICES
SAFETY
In this way they ensure that the seat belt ment compartment: go to a Fiat tion in case of front crash.
adheres perfectly to the wearer before the Dealership to have the device re-
restraining action begins. placed when the expiration date ap-
CORRECT USE
proaches.
OF THE CAR
The pretensioner does not require any Contact a Fiat Dealership for any as-
maintenance or greasing. sistance.
CAR
106
103-120 LINEA 1ed GB 3-09-2008 17:30 Pagina 107
AND CONTROLS
DASHBOARD
DEVICES
SAFETY
CORRECT USE
OF THE CAR
F0R0089m F0R0090m F0R0091m
fig. 4 fig. 5 fig. 6
GENERAL INSTRUCTIONS FOR Seat belts must also be used by pregnant Of course they must position the lower
USING THE SEAT BELTS women: risk will be significantly reduced part of the belt very low down so that it
for both the expectant mother and the passes under the abdomen, see fig. 4.
LIGHTS AND
MESSAGES
WARNING
The driver is responsible for respecting child in the event of an accident.
and ensuring that all the other occupants
of the car also respect the local laws in
force in relation to the use of seat belts.
Always fasten the seat belts before start- WARNING
EMERGENCY
The belt must not be twist-
IN AN
ing off.
ed. The upper part must
cross the shoulder and the chest di-
agonally. The lower part must adhere
SPECIFICATIONS MAINTENANCE
to the hips fig. 4 not to the abdomen.
CAR
Do not use devices (clips, etc.) to hold
the seat belt away from your body.
TECHNICAL
INDEX
107
103-120 LINEA 1ed GB 3-09-2008 17:30 Pagina 108
For maximum safety, keep If the belt has been subject- Each seat belt may only be
the back of your seat up- ed to heavy stress, for ex- used by one person at a
right, lean back into it and make sure ample after and accident, it should be time: do not carry children on your
the seat belt fits closely across your changed completely together with lap with one seat belt protecting
chest and hips. Always fasten the seat the anchors, anchor fastening screws both. In general, do not place any ob-
DEVICES
SAFETY
belts on both the front and the rear and the pretensioners. In fact, even if jects between the person and belt.
seats. Travelling without seat belts the belt has no visible defects, it could
will increase the risk of severe injury have lost its resilience.
CORRECT USE
cident.
LIGHTS AND
MESSAGES
WARNING
WARNING
Never disassemble or tamper
with the seat belt or preten-
sioner components. All interventions
EMERGENCY
108
103-120 LINEA 1ed GB 3-09-2008 17:30 Pagina 109
AND CONTROLS
DASHBOARD
BELTS ALWAYS IN EFFICIENT
CONDITIONS
For optimal protection in the event of a Group 0 0-10 kg in weight
Observe the following: crash, all passengers must be seated and
Group 0+ 0-13 kg in weight
❒ always use the belt with the tap taut and wearing adequate restraint systems.
DEVICES
SAFETY
never twisted; make sure that it is free This is even more important for children. Group 1 9-18 kg in weight
to run without impediments; Group 2 15-25 kg in weight
This prescription is compulsory in all EC
❒ replace the belt after an accident of a countries according to EC Directive Group 3 22-36 kg in weight
CORRECT USE
OF THE CAR
certain severity even if it does not ap- 2003/20/EC.
pear damaged. Always replace the belt As it may be noted, the groups overlap
if the pretensioners where deployed. A child’s head is larger and heavier in pro- partly and in fact, in commerce it is pos-
portion to its body and the child’s muscu- sible to find devices that cover more than
❒ to clean the belt, wash by hand with wa- lar and bone structures are not fully de- one weight group.
LIGHTS AND
ter and mild soap, rinse and leave to dry
MESSAGES
WARNING
veloped. For this reason, they require re-
in the shade. Do not use strong deter- straint systems which are different from All restraint devices must bear the certi-
gents, bleach, paints or any other sub- those used by adults to protect them in the fication data, together with the control
stance which could damage the belt fi- event of an accident. The research results brand, on a solidly fixed label which must
bres; in relation to the best protection for chil- absolutely never be removed.
EMERGENCY
❒ keep the reels dry: correct operation dren is illustrated in European Regulation
IN AN
may only be ensured if the reels are dry; EEC-R44 which divides the restraint sys-
tems into five groups in addition to mak-
❒ replace the seat belt when showing sig- ing their use compulsory:
SPECIFICATIONS MAINTENANCE
nificant wear or cut signs.
TECHNICAL
INDEX CAR
109
103-120 LINEA 1ed GB 3-09-2008 17:30 Pagina 110
vices are recommended having been the baby regardless of the severity of ger side airbags (front and
specifically designed for Fiat cars. the collision. It is advisable to carry side bags, where provided) must be
children in an appropriate restraint deactivated using the setup menu.
Check the warning light F on the in-
CORRECT USE
most protected position in the event strument panel. Move the passenger’s
of an accident. seat as far back as possible to avoid
contact between the cradle and the
dashboard.
LIGHTS AND
MESSAGES
WARNING
EMERGENCY
IN AN
SPECIFICATIONS MAINTENANCE
TECHNICAL CAR
IINDEX
110
103-120 LINEA 1ed GB 3-09-2008 17:30 Pagina 111
AND CONTROLS
DASHBOARD
DEVICES
SAFETY
CORRECT USE
OF THE CAR
F0R0092m F0R0093m F0R0094m
fig. 7 fig. 8 fig. 9
LIGHTS AND
MESSAGES
WARNING
backwards on a cradle seat, which, sup- dren may be carried facing forwards, with seat belts directly fig. 9. The child seat is
porting the head, does not induce stress seat fitted with front cushion, through only needed to position the child correctly
on the neck in the event of sharp decel- which the car seat belt restrains both child with respect to the belts so that the di-
eration. and seat fig. 8. agonal section crosses the child’s chest
and never the neck and is snug on the hips
EMERGENCY
The cradle is restrained by the car seat
not the abdomen.
IN AN
belts fig. 7 and in turn it must restrain the
child with its own belts.
SPECIFICATIONS MAINTENANCE
WARNING
CAR
WARNING The figure is indicative for
The figures are indicative for assembly purposes only. Refer to the in- assembly purposes only. Re-
structions supplied with the child restraint. fer to the instructions supplied with
the child restraint.
TECHNICAL
WARNING
Some child restraint systems for weight group 0 and 1 have a rear at-
tachment to the car seat belts and its own seat belts for securing the child.
Due to their weight, they may be dangerous if incorrectly mounted (e.g. if fastened
INDEX
to the car seat belts with a cushion in between). Follow the assembly instructions
carefully.
111
103-120 LINEA 1ed GB 3-09-2008 17:30 Pagina 112
F0R0095m
fig. 10
Group 0, 0+ up to 13 kg U (▼) U *
GROUP 3
For children from 22 kg to 36 kg the size Group 1 9-18 kg U (▼) U *
LIGHTS AND
MESSAGES
WARNING
Children taller than 1.50 m can wear seat U = suitable for child restraint systems of the “Universal” category, according to Eu-
belts like adults. ropean Standard EEC-R44 for the specified “Groups”.
SPECIFICATIONS MAINTENANCE
(▼) on cars not fitted with passenger’s seat adjustable in height, the seat back shall be
CAR
112
103-120 LINEA 1ed GB 3-09-2008 17:30 Pagina 113
Below is a summary of the rules of 4) Always check the seat belt is well fas-
AND CONTROLS
WARNING
DASHBOARD
safety to be followed for carrying tened by pulling the webbing.
Do not place a cradle seat
children: 5) Only one child is to be strapped to facing backwards on the
1) The recommended position for in- each retaining system. front seat if the passenger side airbag
stalling child’s seat is on the rear seat, as 6) Always check the seat belts do not fit is on. Deployment of the airbag in an
accident could cause fatal injuries to
DEVICES
it is the most protected in the case of a
SAFETY
around the child’s throat.
crash. the baby regardless of the severity of
7) While travelling, do not let the child the collision. It is advisable to carry
2) If the passenger’s air bag is deactivat- sit incorrectly or release the belts. children in an appropriate restraint
ed always check the amber warning light
CORRECT USE
system on the rear seat which is the
OF THE CAR
on the cluster to make sure that it has ac- 8) Never carry children on your lap, even most protected position in the event
tually been deactivated. newborns. No-one, however strong, can of an accident.
hold a child in the case of an accident.
3) Carefully follow the instructions sup-
plied with the child restraint system which 9) In case of an accident, replace the
LIGHTS AND
MESSAGES
WARNING
are mandatory by law. Keep the instruc- child’s seat with a new one.
tions in the car along with the other pa-
pers and this handbook. Do not use child
seats without instructions.
EMERGENCY
IN AN
SPECIFICATIONS MAINTENANCE
TECHNICAL
INDEX CAR
113
103-120 LINEA 1ed GB 3-09-2008 17:30 Pagina 114
AND CONTROLS
DASHBOARD
“UNIVERSAL ISOFIX”
CHILD RESTRAINT
ASSEMBLY SETUP
This car is preset for mounting the Uni-
DEVICES
SAFETY
the “Universal Isofix” one. Universal Isofix “Duo Plus” child seat is WARNING
available from Lineaccessori Fiat. Fit the child seat when the
Remember that in case of Universal Isofix
child’s seat, you can only use all those For any further installation/use detail, re- car is stationary. The child
TECHNICAL
seats approved with the marking EEC fer to the “Instructions Manual” that must seat is correctly anchored to the
R44/03 “Universal Isofix”. be provided by the child restraint system brackets when you hear the click. Fol-
Manufacturer. low the instructions for assembly, dis-
assembly and positioning that the
manufacturer must supply with the
IINDEX
child seat.
114
103-120 LINEA 1ed GB 3-09-2008 17:30 Pagina 115
AND CONTROLS
DASHBOARD
UNIVERSAL ISOFIX CHILD’S SEAT USE
The table below, according to EKE 16 European Directive, shows the different instal- The car is provided with front airbags for
lation possibilities of Isofix restraint systems on seats fitted with Universal Isofix fas- the driver and the passenger.
teners. The front driver / passenger air bags have
DEVICES
SAFETY
Weight group Orientation Class Isofix position been designed to protect the occupants in
child seat Isofix size rear side the event of head-on crashes of medium-
high severity, by placing the cushion be-
Group 0 0 to 10 kg Facing backwards E IL tween the occupant and the steering
CORRECT USE
OF THE CAR
wheel or dashboard.
Facing backwards E IL Front air bags are designed to protect
car’s occupants in front crashes and there-
Group 0+ 0 to 13 kg Facing backwards D IL fore non-activation in other types of col-
LIGHTS AND
lisions (side collisions, rear shunts, roll-
MESSAGES
WARNING
Facing backwards C IL overs, etc.) is not a system malfunction.
Facing backwards D IL An electronic control unit will make the
bag inflate in the event of a frontal crash.
The bag will inflate instantaneously placing
EMERGENCY
Facing backwards C IL
IN AN
itself between the front occupant’s body
Group 1 and the structures which could cause in-
Facing forwards B IUF
to 9 up to 18 kg jury. It will deflate immediately afterwards.
Facing forwards B1 IUF
SPECIFICATIONS MAINTENANCE
Driver and passenger front airbags are not
a replacement of but complementary to
CAR
Facing forwards A IUF
the belts, which you are recommended to
always wear, as specified by law in Europe
and most non-European countries.
IUF: suitable for Isofix child restraint systems to be set facing forwards, universal class
TECHNICAL
(fitted with third upper fastener), approved for the weight group. The volume of front air bags at max. in-
flation fills most of the space between the
IL: suitable for special child restraint systems. Isofix type suitable and tested for this type steering wheel and the driver and between
of car. The seat may be installed by moving the front seat forward. the dashboard and the passenger.
INDEX
115
103-120 LINEA 1ed GB 3-09-2008 17:30 Pagina 116
Front air bag may not be activated in the board because these could interfere
following situations: with the correct opening of the airbag
❒ in collisions against highly deformable (e.g. mobile phones) and cause severe
CORRECT USE
injury to occupants.
OF THE CAR
F0R0099m
objects not affecting the car front sur- fig. 14
face (e.g. bumper collision against guard
rail, etc.);
❒ jamming of the car underneath other The airbags are not deployed in the event
LIGHTS AND
MESSAGES
WARNING
vehicles or protective barriers (e.g. un- of collisions of low severity (for which the
derneath a truck or a guard rail); in this withholding action of the seat belts is suf-
case, the bags would offer no addition- ficient). For this reason, the seat belt must
al protection with respect to the seat be worn at all times. In the case of side
belt and their deployment is unneces-
EMERGENCY
116
103-120 LINEA 1ed GB 3-09-2008 17:30 Pagina 117
MANUAL DEACTIVATION OF
AND CONTROLS
WARNING WARNING
DASHBOARD
PASSENGER’S FRONT AIR BAG
SEVERE DANGER: Do not To deactivate the passen-
arranged cradle child re- AND SIDE BAG (where provided) ger’s front air bag and the
straints facing backwards if Should it be absolutely necessary to car- Side Bag (where provided), refer to
the passenger’s airbag is on. ry a child on the front seat, the passenger’s paragraphs “Digital display” and
Deployment of the airbag in “Multifunctional display” in section
DEVICES
front air bag and the Side Bag (where pro-
SAFETY
an accident could cause fa- vided) can be deactivated. “Dashboard and controls”.
tal injuries to the baby. Always deac-
tivate the passenger’s airbag when The instrument panel warning light F
will stay on glowing steadily until reacti-
CORRECT USE
placing a child seat on the front seat.
OF THE CAR
Move the passenger’s seat as far back vating the passenger’s front air bag and the
as possible to avoid contact between Side Bag (where provided).
the cradle and the dashboard. Al-
though this is not mandatory by law,
LIGHTS AND
MESSAGES
the airbag should be immediately re-
WARNING
activated when children are no longer
carried to ensure better protection to
adults.
EMERGENCY
IN AN
SPECIFICATIONS MAINTENANCE
TECHNICAL
INDEX CAR
117
103-120 LINEA 1ed GB 3-09-2008 17:30 Pagina 118
AND CONTROLS
DASHBOARD
SIDE AIRBAGS
The car is fitted with front side bags for
driver and passenger (where provided) for
protecting the chest and window bags
(where provided) for protecting front and
DEVICES
SAFETY
of the cushion. The cushion immediately of the occupants’ chest and pelvis zone in proper finishing.
inflates, placing itself as a protection, be- the event of a side crash of medium-high
tween the occupant’s body and the struc- Window bags have been designed for pro-
severity. tecting the head of front and rear occu-
ture that could cause injuries. Immediate-
SPECIFICATIONS MAINTENANCE
ly after, the cushion deflates. pants in the event of side crash, thanks to
the wide cushion inflation surface.
CAR
and most non-European countries. seat, allowing thus a correct window bag
unfolding.
IINDEX
118
103-120 LINEA 1ed GB 3-09-2008 17:30 Pagina 119
IMPORTANT The front air bags and/or If you are having the car scrapped, have GENERAL WARNINGS
AND CONTROLS
DASHBOARD
side bags may be deployed if the car is sub- the air bag system deactivated at a Fiat
ject to heavy knocks or accidents involv- Dealership first. If the car changes own- WARNING
ing the underbody area, such as for ex- ership, the new owner must be informed
ample violent shocks, against steps, kerbs of the method of use of air bags and the If when turning the key to
or low obstacles, falling of the car in big above warnings and also be given this MAR the warning light ¬
does not turn on or if it stays on when
DEVICES
SAFETY
holes or sags in the road. “Owner’s Handbook”.
travelling (together with the message
IMPORTANT A small amount of dust will IMPORTANT Pretensioners, front airbags on the multifunctional display, where
be released when the airbags are de- and front side bags are deployed accord- provided) there could be a failure in
ployed. The dust is not harmful and does ing to different logics on the basic of the
CORRECT USE
safety systems; in this event air bags
OF THE CAR
not indicate the beginning of a fire. Fur- type of collision. Non deployment of one or pretensioners could not trigger in
thermore, the surface of the deployed bag of the devices does not therefore indicate case of impact or, in a minor number
and the interior of the car may be covered a system fault. of cases, they could trigger acciden-
in a dusty residue: this dust may irritate tally. Contact Fiat Dealership imme-
LIGHTS AND
the skin and the eyes. Wash with mild
MESSAGES
diately to have the system checked.
WARNING
soap and water in the event of exposure.
The expiration date of the explosive WARNING
charge and the clock wire are shown on a Never rest head, arms and
EMERGENCY
specific label contained in the oddment elbows on the door, on the
WARNING
IN AN
compartment. Go to a Fiat Dealership windows and in the window bag area
to have the devices replaced when the ex- to prevent possible injuries during in- Do not cover the backrest of
piration date approaches. flation phase. front and rear seats with
trims or covers that are not suitable
SPECIFICATIONS MAINTENANCE
IMPORTANT Should an accident occur in to be used with side bags.
which any of the safety devices is activat-
CAR
ed, take the car to a Fiat Dealership to
have the devices activated replaced and to WARNING
have the system checked.
Never lean head, arms and
TECHNICAL
All inspection, repair and replacement op- WARNING
elbows out of window.
erations concerning the air bags must on- Never travel with objects on
ly be carried out c/o Fiat Dealership. your lap, in front of your
chest or with a pipe, pencil, etc. be-
tween your lips; injury may result in
INDEX
the event of the air bag being trig-
gered.
119
103-120 LINEA 1ed GB 3-09-2008 17:30 Pagina 120
Always drive holding your Have the airbag system The airbag deployment
hands on the steering wheel checked by a Fiat Dealership threshold is higher than that
rim so that the airbag can inflate if the car was stolen, if theft was at- of the pretensioners. For collisions in
freely in the case of need. Do not dri- tempted, or if the car was subjected the range between the two thresh-
ve with your body bent forward. Keep to vandalism or flooding. olds, it is normal for only the preten-
DEVICES
SAFETY
WARNING
When the key is turned to WARNING
WARNING MAR warning light F (with Do not hook rigid objects to
Airbags may be deployed if passenger front airbag activate) will the coat hooks and to the
LIGHTS AND
MESSAGES
ployed in a collision. Non deployment Do not wash the seats with airbags are not deployed in low speed
of the devices in this case does not in-
CAR
120
121-132 LINEA 1ed GB 3-09-2008 17:30 Pagina 121
AND CONTROLS
DASHBOARD
ENGINE STARTING ........................................................... 122
PARKING................................................................................ 125
DEVICES
SAFETY
USING THE MANUAL GEARBOX ................................. 126
CONTAINING RUNNING COSTS................................. 127
SNOW TYRES ....................................................................... 131
CORRECT USE
OF THE CAR
SNOW CHAINS ................................................................... 131
CAR INACTIVITY ............................................................... 132
LIGHTS AND
MESSAGES
WARNING
EMERGENCY
IN AN
SPECIFICATIONS MAINTENANCE
TECHNICAL
INDEX CAR
121
121-132 LINEA 1ed GB 3-09-2008 17:30 Pagina 122
AND CONTROLS
DASHBOARD
ENGINE STARTING Do not leave the key in the ig-
STARTING PROCEDURE FOR
nition switch with the engine PETROL VERSIONS
The car is provided with an electronic en- off to avoid unnecessary con- Proceed as follows:
gine lock device: refer to “The Fiat CODE sumption of electricity which
system” paragraph in “Dashboard and could drain the battery. It is dangerous ❒ ensure that the handbrake is up;
controls” if you cannot start the engine. to run the engine in closed environ- ❒ put the gear lever into neutral;
DEVICES
SAFETY
122
121-132 LINEA 1ed GB 3-09-2008 17:30 Pagina 123
If, when the ignition key is at MAR, the in- STARTING PROCEDURE FOR If the engine does not start at the first at-
AND CONTROLS
DASHBOARD
strument panel warning light Y remains DIESEL VERSIONS tempt, return the ignition key to STOP
lit together with warning light U turn the before repeating starting.
key to STOP and then back to MAR; re- Proceed as follows:
main on, try with the other keys provid- If, when the ignition key is at MAR , the
❒ ensure that the handbrake is up; instrument panel warning light Y re-
ed with the car.
❒ put the gear lever into neutral; mains lit together with warning light m
DEVICES
SAFETY
IMPORTANT if Y on the instrument turn the key to STOP and then back to
panel remains on and steady, go to a Fiat ❒ turn the ignition key to MAR; instru- MAR; if the warning lights remain on, try
Dealership immediately. ment panel warning lights m and Y with the other keys provided with the car.
will light up;
CORRECT USE
OF THE CAR
IMPORTANT Never leave the ignition key IMPORTANT If the instrument panel
to MAR when the engine is off. ❒ wait for the warning light Y e mto warning light Y stays on glowing
turn off. The hotter the engine is, the steadily, contact immediately Fiat Deal-
quicker this will happen; ership.
❒ press the clutch pedal down to the
LIGHTS AND
MESSAGES
WARNING
IMPORTANT Never leave the ignition key
floor without touching the accelerator; to MAR when the engine is off.
❒ turn the ignition key to AVV as soon
as warning light m goes out. Waiting
EMERGENCY
too long will waste the work done by
IN AN
the glow plugs. Release the key as soon Warning light m will blink
as the engine starts. for 60 seconds after starting
or during prolonged cranking
to indicate a fault to the glow
SPECIFICATIONS MAINTENANCE
plug heating system. Use the car nor-
CAR
mally if the engine starts and go to a
Fiat Dealership as soon as possible.
TECHNICAL
INDEX
123
121-132 LINEA 1ed GB 3-09-2008 17:30 Pagina 124
❒ drive off slowly, letting the engine turn breath” before turning it off by letting it
at medium revs. Do not accelerate idle to allow the temperature in the en-
abruptly; gine compartment to fall.
CORRECT USE
124
121-132 LINEA 1ed GB 3-09-2008 17:30 Pagina 125
AND CONTROLS
DASHBOARD
brake:
Proceed as follows: ❒ slightly lift the handbrake and press re-
❒ stop the engine and engage the hand- lease button A;
brake; ❒ hold button A pressed and lower the
DEVICES
SAFETY
❒ engage a gear (on a slope, engage first lever. Warning light x on the instru-
gear if the car is faced uphill or reverse ment panel will go out.
if it is faced downhill) and leave the Press the brake pedal when carrying out
wheels steered.
CORRECT USE
this operation to prevent the car from
OF THE CAR
F0R0103m
fig. 1
If the car is parked on a steep slope, it is moving accidentally.
further advisable to block the wheels with HANDBRAKE fig. 1
a wedge or stone. Do not leave the key in
the ignition switch to prevent draining the The handbrake lever is located between
LIGHTS AND
MESSAGES
WARNING
battery. Always remove the key when you the two front seats.
leave the car. Pull the lever upwards to operate the
handbrake. Four or five notches are nor-
mally sufficient to lock the car on flat ter-
EMERGENCY
rain, while nine or ten may be necessary
IN AN
WARNING on a steep slope with the car loaded.
Never leave children unat-
tended in the car. Always re- IMPORTANT If this is not the case, con-
move the ignition key when leaving tact Fiat Dealership to have the handbrake
SPECIFICATIONS MAINTENANCE
the car and take it out with you. adjusted.
CAR
When the handbrake lever is pulled up
and the ignition key is at MAR, the in-
strument panel warning light x will turn
on.
TECHNICAL
INDEX
125
121-132 LINEA 1ed GB 3-09-2008 17:30 Pagina 126
AND CONTROLS
DASHBOARD
USING THE MANUAL
GEARBOX
To engage the gears, press the clutch ped-
al fully and shift the gear lever into one of
DEVICES
F0R0154m F0R0105m
the engine running, wait for at least 2 sec- fig. 2 - 1.4 version fig. 3 - 1.3 Multijet version
onds with the clutch pedal fully pressed
before engaging reverse to prevent dam- IMPORTANT The clutch pedal must be WARNING
age to the gears and grating. used for gear shift only. Never drive with
the foot resting, even if slightly, on the Press the clutch pedal fully
LIGHTS AND
MESSAGES
WARNING
Version 1.4: to engage reverse R from neu- clutch pedal. For versions / markets where to change gears correctly.
tral position, lift the sliding ring A under applicable, the clutch pedal control elec- For this reason, there must be no ob-
the knob and shift the lever rightwards and tronics can intervene interpreting the stacles on the floor under the pedals:
then back fig. 2. wrong drive style as a fault. make sure that mat are always flat
and do not interfere with the pedals.
EMERGENCY
nal components.
INDEX
126
121-132 LINEA 1ed GB 3-09-2008 17:30 Pagina 127
AND CONTROLS
DASHBOARD
RUNNING COSTS Remove the roof rack or the ski rack from
Starting
the roof after use. These accessories de-
Here are some suggestions which may crease aerodynamic penetration of the car Do not warm the engine up with the car
help you to keep the running costs of your and have a negative effect on consumption. standing: the engine warms up very slow-
It is better to use a trailer to transport
DEVICES
car down and lower the amount of toxic ly in these conditions, increasing con-
SAFETY
emissions released into the atmosphere. particularly bulky objects. sumption and emissions. It is advisable to
start off immediately and slowly keeping
GENERAL CONSIDERATIONS Electric devices the engine speed down: the engine will
CORRECT USE
warm up much faster this way.
OF THE CAR
Use electric devices only for the amount
Car maintenance of time needed. Rear heated window, ad-
ditional headlights, windscreen wipers and Unnecessary actions
Have checks and adjustments carried out
in accordance with the “Service schedule”. heater fan need a considerable amount of Avoid revving up when starting at traffic
energy, therefore increasing the require-
LIGHTS AND
lights or before stopping the engine. The
MESSAGES
WARNING
ment of current increases fuel consump- latter action, like doubling the clutch, is un-
Tyres tion (up to +25% in the urban cycle). necessary and causes increase of con-
Check tyre pressure regularly at least sumption and pollution.
once every four weeks: excessively low Climate control
EMERGENCY
pressure will increase consumption be- Gear selection
IN AN
cause rolling resistance will be higher. The climate control system requires high-
er fuel consumption (up to +20% in av- Use a higher gear as soon as traffic and
erage): use the air vents when the exter- road conditions allow. Using a low gear
Unnecessary loads nal temperature allows to. for faster acceleration will increase con-
SPECIFICATIONS MAINTENANCE
Do not travel with too much luggage sumption.
CAR
stowed in the boot. The weight of the car Spoilers
(especially when driving in town) and its In the same way improper use of a high
trim greatly affects consumption and sta- The use of non-certified aerodynamic gear increases consumption, emissions an
bility. items may adversely affect air drag and engine wear.
TECHNICAL
consumption levels.
INDEX
127
121-132 LINEA 1ed GB 3-09-2008 17:30 Pagina 128
Sudden acceleration has a very negative Traffic and Install any specific and/or additional rear-
effect on consumptions and emissions: ac- road conditions view mirrors as specified by law.
celerate gradually and do not go over the Rather high consumption is caused by
maximum torque ratio. Remember that when towing a trailer,
heavy traffic, for instance when travelling steep hills are harder to climb, the brak-
LIGHTS AND
MESSAGES
WARNING
in a queue with frequent use of low gears ing spaces increase and overtaking takes
or in cities with many traffic lights. Moun- longer depending on the overall weight.
tain and rough roads also have a negative
effect on consumption. Engage a low gear when driving downhill,
rather than constantly using the brake.
EMERGENCY
IN AN
128
121-132 LINEA 1ed GB 3-09-2008 17:30 Pagina 129
Respect the speed limits specific for each INSTALLING THE TOW An electric brake should be supplied di-
AND CONTROLS
DASHBOARD
country for vehicles towing trailers. In all HOOK rectly by the battery through a cable with
cases, the top speed must not exceed 100 a cross section of no less than 2.5 mm2.
km/h. The towing device should be fastened to
the body by specialised personnel accord- IMPORTANT Electric brake or other de-
Fit a suitable towing stabilizer to the trail- ing to any additional and/or integrative in- vice shall be used with running engine.
er to be towed. formation supplied by the Manufacturer of
DEVICES
SAFETY
In addition to the electrical branches, the
the device. car’s electric system can only be con-
The towing device must meet current reg- nected to the supply cable for an electric
ulations with reference to 94/20/EEC brake and to the cable for an internal light,
CORRECT USE
WARNING
OF THE CAR
Directive and subsequent amendments. though not above 15W.
The ABS with which the car
may be equipped will not For any version the towing device used For connections use the preset control
control the braking system of the must match the towable weight of the car unit with battery cable no less than 2.5
trailer. Particular caution is required on which it is to be installed. mm2.
LIGHTS AND
MESSAGES
WARNING
on slippery roads. For the electric connection a unified con-
nector should be used which is generally
placed on a special bracket normally fas-
tened to the towing device, and a special
EMERGENCY
ECU for external trailer light control shall
IN AN
WARNING be installed on the car.
Never modify the braking
system of the car to control For the electrical connection, 7 or 13 pin
the trailer brake. The trailer braking 12VDC connection is to be used (CU-
SPECIFICATIONS MAINTENANCE
system must be fully independent NA/UNI and ISO/DIN Standards). Follow
CAR
from the hydraulic system of the car. the instructions provided by the car man-
ufacturer and/or the tow hitch manufac-
turer.
TECHNICAL
INDEX
129
121-132 LINEA 1ed GB 3-09-2008 17:30 Pagina 130
To load
The hook should be fastened to the body
Existing screw
CORRECT USE
WARNING
Existing screw
Type-approved ball
After fitting, screw holes
shall be sealed to prevent ex-
SPECIFICATIONS MAINTENANCE
Existing hole
TECHNICAL
Existing screw
Existing screw
INDEX
F0R0190m
fig. 3
130
121-132 LINEA 1ed GB 3-09-2008 17:30 Pagina 131
SNOW TYRES IMPORTANT When snow tyres are used SNOW CHAINS
AND CONTROLS
DASHBOARD
with a max speed index below the one
Use snow tyres of the same size as the that can be reached by the car (increased Use of snow chains should be in compli-
normal tyres provided with the car. by 5%), place a notice in the passenger’s ance with local regulations.
compartment, plainly in the driver’s view
Fiat Dealership will be happy to provide which states the max permissible speed of The snow chains may be applied only on-
DEVICES
SAFETY
advice concerning the most suitable type the snow tyres (as per EC Directive). to the front wheel tyres (drive wheels).
of tyre for the customer’s requirements. Use of Lineaccessori Fiat snow chains is
All four tyres should be the same (brand recommended.
For the type of tyre to be used, inflation and track) to ensure greater safety when
pressures and the specifications of snow Check the tension of the chains after the
CORRECT USE
driving and braking and better driveability.
OF THE CAR
tyres, follow the instructions given in para- first few metres have been driven.
graph “Wheels” in section “Technical Remember that it is inappropriate to
specifications”. change the direction of rotation of tyres. IMPORTANT With snow chains, use the
accelerator with extreme care to prevent
The performance of these tyres is con- or to limit as much as possible slipping of
LIGHTS AND
MESSAGES
WARNING
siderably reduced when the tread depth the driving wheels that could cause chain
is less than 4 mm. Replace them in this WARNING breaking resulting in damages to the car
case. body or mechanical components.
The max speed for snow
Due to their specific features, the perfor- tyres with “Q” marking is IMPORTANT Use low-clearance 9 mm
EMERGENCY
mance of snow tyres is much lower than 160 km/h; 190 km/h for tyres with “T” snow chains.
IN AN
that of normal types in normal conditions marking and 210 km/h for tyres with
or long motorway stretches. Limit per- H marking. The Road Traffic Code
formance according the use for which they speed limits must however be always
SPECIFICATIONS MAINTENANCE
were approved. strictly observed.
TECHNICAL
INDEX CAR
131
121-132 LINEA 1ed GB 3-09-2008 17:30 Pagina 132
snow chains are fitted. Do the electric system, check its charge
not exceed 50 km/h. Avoid gaged; every month (see paragraph “Charge
potholes, steps and pave- level check” in chapter “Maintenance
ments and avoid also to dri- ❒ disconnect the negative battery termi-
nal and check battery charge (see para- and care”);
ve for long distances on
LIGHTS AND
graph “Charge level check” in chapter ❒ recharge the battery if necessary (see
MESSAGES
WARNING
❒ clean and protect the painted parts us- the car alarm with the remote control.
ing protective wax;
SPECIFICATIONS MAINTENANCE
able;
❒ sprinkle talcum powder on the rubber
windscreen and rear window wiper
TECHNICAL
132
133-144 LINEA 1ed GB 3-09-2008 17:31 Pagina 133
WA R N I N G L I G H T S A N D M E S S A G E S
AND CONTROLS
DASHBOARD
GENERAL WARNINGS ..................................................... 134 FIAT CODE PROTECTION
SYSTEM FAILURE.................................................................. 140
LOW BRAKE FLUID ............................................................ 134
DEVICES
SAFETY
EXTERNAL LIGHTS FAILURE........................................... 141
HANDBRAKE ON................................................................ 134
AIR BAG FAILURE................................................................ 135 REAR FOG LIGHTS.............................................................. 141
CORRECT USE
OF THE CAR
HOT GENERIC FAILURE INDICATION ................................. 141
ENGINE COOLANT ........................................................... 135
ESP SYSTEM FAILURE ........................................................ 142
LOW BATTERY CHARGE ................................................. 136
BRAKE PAD WEAR ............................................................ 142
LIGHTS AND
MESSAGES
WARNING
LOW ENGINE OIL PRESSURE.......................................... 136
PARKING SENSOR FAILURE ............................................ 143
INCOMPLETE DOOR LOCKING.................................... 137
SIDELIGHTS AND LOW BEAMS ..................................... 143
SEAT BELTS NOT FASTENED.......................................... 137
EMERGENCY
IN AN
EBD SYSTEM FAILURE ........................................................ 137 FOLLOW ME HOME ........................................................... 143
SPECIFICATIONS MAINTENANCE
LEFT-HAND DIRECTION INDICATOR........................ 143
CAR
EOBD SYSTEM FAILURE (PETROL VERSIONS) ......... 138
RIGHT-HAND DIRECTION INDICATOR.................... 143
FRONT PASSENGER AIRBAG DEACTIVATED........... 139
CRUISE CONTROL ............................................................ 143
TECHNICAL
ABS SYSTEM FAILURE......................................................... 139
MAIN BEAM HEADLIGHTS ............................................... 143
FUEL RESERVE....................................................................... 139
GLOW PLUG WARMING ................................................ 140 POSSIBLE PRESENCE OF ICE ON THE ROAD ........... 144
INDEX
GLOW PLUG WARMING FAILURE ............................... 140 LIMITED RANGE ................................................................. 144
WATER IN DIESEL FUEL FILTER ..................................... 140 ASR SYSTEM ......................................................................... 144
133
133-144 LINEA 1ed GB 3-09-2008 17:31 Pagina 134
Lighting of a warning light is associated to warning light turns on, but it should go off
a specific message and/or buzzer when ap- after few seconds. IMPORTANT If the warning light turns on
plicable. These indications are brief and when travelling, check that the handbrake
precautionary and as such must non be is not engaged.
CORRECT USE
OF THE CAR
cycle in both cases. The warning light on sage on the display) stop the car im-
the instrument panel will stay on until the mediately and contact Fiat Dealer-
cause of the fault is eliminated. ship.
TECHNICAL
INDEX
134
133-144 LINEA 1ed GB 3-09-2008 17:31 Pagina 135
AND CONTROLS
WARNING
¬
DASHBOARD
(red)
If when turning the key to ç COOLANT (red)
MAR the warning light ¬
Turning the ignition key to does not turn on or if it stays on when Turning the ignition key to
MAR the warning light turns on, but it travelling (together with the message MAR the warning light turns on, but it
should go off after few seconds. on the multifunctional display, where should go off after few seconds.
DEVICES
SAFETY
The warning light stays on steady if there provided) there could be a failure in The warning light turns on when the en-
is a failure in the airbag system. safety systems; in this event air bags gine is overheated.
or pretensioners may not be deployed
On certain versions the dedicated message If the warning light comes on, proceed as
CORRECT USE
in case of impact or, in a minor num-
OF THE CAR
is displayed. ber of cases, they be deployed acci- follows:
dentally. Contact Fiat Dealership im- ❒ during normal travel: stop the car,
mediately to have the system checked. stop the engine and check that the wa-
ter level in the vessel is not under the
LIGHTS AND
MESSAGES
WARNING
MIN line. In this case, wait for a few
minutes for the engine to cool down
when slowly and carefully open the
WARNING cap, top-up with coolant and check
Failure of warning light ¬ that the level is between the MIN and
EMERGENCY
IN AN
(warning light off) is indicat- MAX references on the vessel itself.
ed by warning light F which will Also check for leakages. Go to a Fiat
blink for longer than the normal 4 Dealership if the warning should come
seconds indicating that the front pas- on when the engine is started again.
SPECIFICATIONS MAINTENANCE
senger airbag is off.
TECHNICAL
INDEX CAR
135
133-144 LINEA 1ed GB 3-09-2008 17:31 Pagina 136
❒ In the case of demanding use (e.g. LOW BATTERY LOW ENGINE OIL
AND CONTROLS
DASHBOARD
towing trailers uphill or car at full
load): slow down and stop the car if w CHARGE (red) v PRESSURE (red)
the warning light stays on. Stand for Turning the ignition key to Turning the ignition key to
2 or 3 minutes with the engine running MAR the warning light turns on, but it MAR the warning light turns on, but it
and slightly accelerated to promote a should go out as soon as the engine is should go out as soon as the engine is
DEVICES
SAFETY
better circulation of coolant. Then started (with the engine running at idle started.
stop the engine. Check correct liquid speed a brief delay in going out is allowed).
level as described above. On certain versions the dedicated message
Go to a Fiat Dealership immediately if the is displayed.
IMPORTANT Under severe use of the
CORRECT USE
a Fiat Dealership.
IN AN
SPECIFICATIONS MAINTENANCE
TECHNICAL CAR
INDEX
136
133-144 LINEA 1ed GB 3-09-2008 17:31 Pagina 137
AND CONTROLS
´ <
DASHBOARD
LOCKING (red) FASTENED (red)
x > (red) (amber)
DEVICES
SAFETY
shut. The warning light will blink and a buzzer will EBD system failure or that the system is
sound if the front seat belts are not cor- not available. Early locking of the rear
On certain versions the dedicated message rectly fastened. The buzzer of the S.B.R.
is displayed. wheels may occur in the event of violent
(Seat Belt Reminder) system may only be braking causing the car to swerve. Drive
CORRECT USE
OF THE CAR
A buzzer will sound when doors/tailgate switched off by a Fiat Dealership. On some very carefully to a Fiat Dealership to have
are open and the car is moving. versions the system may be reactivated the system inspected.
from the setup menu.
On certain versions the dedicated message
is displayed.
LIGHTS AND
MESSAGES
WARNING
EMERGENCY
IN AN
SPECIFICATIONS MAINTENANCE
TECHNICAL
INDEX CAR
137
133-144 LINEA 1ed GB 3-09-2008 17:31 Pagina 138
INJECTION SYSTEM EOBD ENGINE CONTROL If the light flashes, release the accelerator
AND CONTROLS
DASHBOARD
U FAILURE
(Multijet versions -
SYSTEM FAILURE
Under normal conditions, turning the ig-
pedal to lower the speed of the engine un-
til the warning light stops flashing; contin-
amber) ue the journey at moderate speed, trying
nition key to MAR, the warning light turns to avoid driving conditions that may cause
EOBD SYSTEM on but it should go off after engine starting. further flashing and contact Fiat Dealer-
This indicates that the warning light is
DEVICES
SAFETY
Under normal conditions, turning the ig- system which could cause high emis- Go to a Fiat Dealership as
nition key to MAR, the warning light turns sions at the exhaust, possible lack of soon as possible if warning
on but it should go off after engine start- performance, poor handling and high light U either does not light
ing. consumption levels. up when the key is turned to
MAR to if while travelling the warning
LIGHTS AND
MESSAGES
WARNING
If the warning light stays on or turns on On certain versions the dedicated mes- lights comes on either steady or blink-
when travelling, means a fault in the sup- sage is displayed. ing (along with a message on the dis-
ply/ignition system which could cause high In these conditions, you may continue play). The operation of warning light
emissions at the exhaust, possible lack of travelling at moderate speed without de- U may be checked by the traffic po-
performance, poor handling and high con-
EMERGENCY
manding excessive effort from the engine. lice using specific devices. Follow the
IN AN
sumption levels. Prolonged use of the car with the warn- laws in force in the country where you
On certain versions the dedicated message ing light on may cause damage. Go to a are driving.
is displayed. Fiat Dealership as soon as possible. If
warning light will go out after the fault
SPECIFICATIONS MAINTENANCE
In these conditions, you may continue goes away but it will be stored in the sys-
CAR
138
133-144 LINEA 1ed GB 3-09-2008 17:31 Pagina 139
AND CONTROLS
DASHBOARD
F AIRBAG
DEACTIVATED > (amber)
K
(amber) Turning the ignition key to Turning the ignition key to
MAR the warning light turns on, but it MAR the warning light turns on, but it
Warning light F comes on when front should go off after few seconds. should go off after few seconds.
DEVICES
SAFETY
passenger’s airbag is deactivated.
The warning light will light up when the The warning light turns on when about 7
With front passenger’s airbag on, turning system is either not working or not avail- litres fuel are left in the tank.
the ignition key to MAR, warning light able. In the case, the braking system will
F comes on steadily for about 4 sec- IMPORTANT The warning light will blink
CORRECT USE
work as normal without the extra poten-
OF THE CAR
onds, it flashes for other 4 seconds and tials offered by the ABS system. Drive to indicate a system failure. Go to a Fiat
then it shall go off. carefully and go to a Fiat Dealership as Dealership to have the system checked.
soon as possible.
On certain versions the dedicated message
LIGHTS AND
MESSAGES
WARNING
WARNING is displayed.
Warning light F indicates
failure of warning light ¬.
This condition is indicated by inter-
EMERGENCY
mittent blinking of warning light F
IN AN
for longer than 4 seconds. In this case,
warning light ¬ may not indicate
fault to the system. Contact Fiat
SPECIFICATIONS MAINTENANCE
Dealership immediately to have the
CAR
system checked before driving off.
TECHNICAL
INDEX
139
133-144 LINEA 1ed GB 3-09-2008 17:31 Pagina 140
AND CONTROLS
GLOW PLUG WATER IN DIESEL CAR PROTECTION
Y
DASHBOARD
m WARMING
(Multijet versions - amber) c FUEL FILTER
(Multijet versions - amber)
SYSTEM FAILURE -
FIAT CODE (amber)
GLOW PLUG Turning the ignition key to MAR the Turning the key to MAR the warning light
WARMING FAILURE warning light turns on, but it should go off shall flash only once and then go off.
DEVICES
SAFETY
IMPORTANT With hot ambient temper- If with the engine running the warning light
ature, warning light stays on for very short The presence of water in the Y flashes, this means that the car is not
time. feeding circuit may cause se- protected by the engine inhibitor device
vere damage to the injection (see “Fiat Code system” in section “Dash-
Glow plug warming failure system and irregular engine
EMERGENCY
140
133-144 LINEA 1ed GB 3-09-2008 17:31 Pagina 141
è
EXTERNAL LIGHT GENERIC FAILURE Rain sensor failure
AND CONTROLS
W
DASHBOARD
FAILURE (amber) INDICATION (where provided)
The warning light will come on (amber) The warning light comes on when a rain
(some versions only) when a fault sensor failure is detected. Go to a Fiat
to one of the following lights is detected: The warning light turns on in the follow- Dealership.
ing circumstances.
DEVICES
SAFETY
– side/taillights The display will show the dedicated mes-
Engine oil pressure sensor failure sage.
– brake lights
The warning light turns on when failure is Parking sensor failure
– rear fog lights
CORRECT USE
detected in parking sensors. Go to a Fiat
OF THE CAR
Dealership to have the fault fixed as soon (where provided)
– direction indicators
as possible. See description of warning light t.
– number plate lights.
The fault may be caused by: one or more External light fault Speed limit exceeded
LIGHTS AND
MESSAGES
WARNING
burnt lamps, a blow protection fuse or in- (where provided) (where provided)
terruption of the electrical connection.
See description of warning light 6. The display will show the dedicated mes-
On certain versions warning light è sage when the car exceeds the set speed
comes on instead. Fuel cut-off switch tripped limit (see “Multifunctional Display” in sec-
EMERGENCY
tion “Dashboard and controls”).
IN AN
On certain versions the dedicated message The warning light comes on when the fu-
is displayed. el cut-off switch trips.
Diesel filter failure
The display will show the dedicated mes- (where provided)
SPECIFICATIONS MAINTENANCE
sage.
The warning light will come on when a
CAR
REAR FOG LIGHTS diesel filter system failure is detected. The
4 (amber) display will show the dedicated message
(where provided).
The warning light comes on
TECHNICAL
when the rear fog lights are turned on.
INDEX
141
133-144 LINEA 1ed GB 3-09-2008 17:31 Pagina 142
Diesel particulate filter clogged ESP SYSTEM FAILURE BRAKE PAD WEAR
AND CONTROLS
á
DASHBOARD
(Multijet versions)
The warning light turns on when the
(amber)
HILL HOLDER FAILURE
d (amber) (red)
diesel particulate filter is clogged and the The warning light on the dial
(amber) turns on if the front brake pads are worn;
driving conditions do not enable to acti-
vate automatically the regeneration pro- in this case have them changed as soon
DEVICES
SAFETY
turns off.
If the warning light does not go off or stays
The display will show the dedicated mes- on when travelling together with the but-
sage. ton led ASR OFF, contact Fiat Dealer-
ship.
LIGHTS AND
MESSAGES
WARNING
142
133-144 LINEA 1ed GB 3-09-2008 17:31 Pagina 143
AND CONTROLS
D
DASHBOARD
t FAILURE
(where provided)
3 AND LOW BEAMS
(green)
DIRECTION
INDICATOR
(amber) (green - intermittent)
FOLLOW ME HOME
The warning light turns on when failure (green) The warning light turns on when the di-
DEVICES
SAFETY
is detected in parking sensors. Side/taillights and low beams rection indicator control lever is moved
upwards or, together with the left indica-
On certain versions warning light è The warning light turns on when side/tail- tor, when the hazard warning light button
lights or low beams are turned on. is pressed.
CORRECT USE
comes on instead.
OF THE CAR
Contact Fiat Dealership. Follow me home
On certain versions the dedicated mes- The warning light will turn when this de-
vice is active (see “Follow me home” in CRUISE CONTROL
Ü
sage is displayed.
(where provided) (green)
LIGHTS AND
section “Dashboard and controls”).
MESSAGES
WARNING
The display will show the dedicated mes- Turning the ignition key to
sage. MAR the warning light turns on, but it
should go off after few seconds.
EMERGENCY
FRONT FOG LIGHTS
IN AN
5
The warning light turns on together with
(green) (where provided) the message on the display when turning
the knurled ring of the Cruise Control to
The warning light turns on ON.
SPECIFICATIONS MAINTENANCE
when the front fog lights are turned on.
On certain versions the dedicated mes-
CAR
sage is displayed.
LEFT-HAND
F DIRECTION
TECHNICAL
INDICATOR MAIN BEAMS (blue)
(green - intermittent)
1 The warning light turns on
The warning light turns on when the di- when the main beams are
rection indicator control lever is moved turned on.
INDEX
downwards or, together with the right in-
dicator, when the hazard warning light
button is pressed.
143
133-144 LINEA 1ed GB 3-09-2008 17:31 Pagina 144
POSSIBLE PRESENCE OF ICE ASR SYSTEM Press ASR OFF again: the LED on the
AND CONTROLS
DASHBOARD
ON THE ROAD (versions with multifunction display) button will go out and a dedicated mes-
(versions with multifunction display) sage will appear on the display to inform
The ASR system can be turned off by uses that the system has been switched
This indication starts flashing when the pressing the button ASR OFF. back on.
outside temperature reaches or falls be- A dedicated message will appear on the
DEVICES
LIMITED RANGE
(versions with multifunction display)
The display will show the dedicated mes-
LIGHTS AND
MESSAGES
WARNING
144
145-176 LINEA 1ed GB 5-09-2008 9:22 Pagina 145
IN AN EMERGENCY
AND CONTROLS
DASHBOARD
STARTING THE ENGINE ................................................. 146
IF A TYRE IS PUNCTURED ............................................... 147
DEVICES
SAFETY
QUICK TYRE REPAIR KIT
FIX & GO automatic............................................................. 153
WHEN NEEDING TO CHANGE A BULB ................... 158
CORRECT USE
OF THE CAR
IF AN EXTERIOR LIGHT BURNS OUT.......................... 160
IF AN INTERIOR LIGHT BURNS OUT .......................... 165
IF A FUSE BLOWS................................................................ 168
LIGHTS AND
MESSAGES
WARNING
IF THE BATTERY IS FLAT .................................................. 174
LIFTING THE CAR............................................................... 175
TOWING THE CAR ........................................................... 175
EMERGENCY
IN AN
SPECIFICATIONS MAINTENANCE
TECHNICAL
INDEX CAR
145
145-176 LINEA 1ed GB 5-09-2008 9:22 Pagina 146
AND CONTROLS
DASHBOARD
STARTING THE Proceed as follows to start the engine:
ENGINE ❒ connect positive terminals (+ near the
terminal) of the two batteries with a
EMERGENCY START-UP jump lead;
Go to a Fiat Dealership immediately if in- ❒ with a second lead, connect the nega-
DEVICES
SAFETY
strument panel warning light Y comes tive terminal (–) of the auxiliary battery
on steady. to an earthing point E on the engine or
the gearbox of the car to be started;
JUMP STARTING fig. 1 ❒ start the engine;
CORRECT USE
OF THE CAR
F0R0242m
fig. 1
If the battery is flat, the engine may be ❒ when the engine has been started, re-
started using an auxiliary battery with the move the leads reversing the order
same capacity or a little higher than the WARNING
above.
flat one. This procedure must be per-
LIGHTS AND
MESSAGES
WARNING
formed by expert personnel If after a few attempts the engine does not
because incorrect actions may cause start, do not insist but contact the near-
electrical discharge of considerable in- est Fiat Dealership.
tensity. Furthermore, battery fluid is
poisonous and corrosive: avoid contact
EMERGENCY
IN AN
146
145-176 LINEA 1ed GB 5-09-2008 9:22 Pagina 147
AND CONTROLS
DASHBOARD
terminals of the two batteries directly:
sparks could ignite explosive gas released Never jump start the engine by pushing,
from the battery. If the auxiliary battery is towing or driving downhill. This could GENERAL INSTRUCTIONS
installed on another car, prevent acciden- cause a flow of fuel into the catalytic con-
tal contact between metallic parts of the verter and damage it beyond repair. Wheel changing and correct use of the
jack and spare wheel call for some pre-
DEVICES
SAFETY
two cars. IMPORTANT Remember that the brake cautions as listed below.
booster and the power steering system
are not operating until the engine is start-
ed, a greater effort will therefore be re-
CORRECT USE
OF THE CAR
quired to press the brake pedal or turn
the steering wheel. WARNING
Indicate that the car is sta-
tionary according to the laws
in force: hazard lights, triangle, etc.
LIGHTS AND
MESSAGES
WARNING
Passengers should leave the car, par-
ticularly if it is very loaded and wait
for the wheel to be changed away
from on-coming traffic. Apply the
handbrake.
EMERGENCY
IN AN
SPECIFICATIONS MAINTENANCE
TECHNICAL
INDEX CAR
147
145-176 LINEA 1ed GB 5-09-2008 9:22 Pagina 148
Important notes:
AND CONTROLS WARNING WARNING
DASHBOARD
The spare wheel is specific The jack may only be used to ❒ the jack weighs 1.76 kg;
for your car. Do not use it on replace wheels on the car ❒ the jack requires no adjustment;
cars of different models. Do not use which it equips or other cars of the
spare wheels of different models on same model. Never use the jack for ❒ the jack cannot be repaired: replace
your car. The wheel bolts are specif- other purposes, such as lifting other
DEVICES
ic for your car. Do not use them on car models. Never use the jack to car-
cares of different models. Do not use ry out repairs under the car. Incorrect ❒ no tool other than its handle may be fit-
bolts of different models on your car. positioning of the jack may cause the ted on the jack.
CORRECT USE
WARNING
LIGHTS AND
MESSAGES
WARNING
cations” chapter.
TECHNICAL
IINDEX
148
145-176 LINEA 1ed GB 5-09-2008 9:22 Pagina 149
AND CONTROLS
DASHBOARD
follows: pulsory by law in certain countries) be-
fore getting out of the car;
❒ stop the car in a position so that it is
not a danger for on-coming traffic and ❒ open the tailgate and lift the mat;
where you can replace the wheel safe-
ly. The ground must be flat and com-
DEVICES
SAFETY
pact;
❒ stop the engine off and pull up the hand-
brake;
CORRECT USE
OF THE CAR
❒ engage first gear or reverse;
LIGHTS AND
MESSAGES
WARNING
EMERGENCY
IN AN
F0R0107m
fig. 2
SPECIFICATIONS MAINTENANCE
❒ loosen the fastener A-fig. 2;
CAR
❒ take out the tool box C-fig. 2 and take
it near to the wheel to be changed;
❒ take the spare wheel B-fig. 2;
TECHNICAL
INDEX
149
145-176 LINEA 1ed GB 5-09-2008 9:22 Pagina 150
AND CONTROLS
DASHBOARD
DEVICES
SAFETY
CORRECT USE
OF THE CAR
F0R0108m
fig. 3
the ground;
❒ warn anybody nearby that the car is
about to be lifted. They must stay clear
and not touch the car until it is back on
SPECIFICATIONS MAINTENANCE
the ground;
TECHNICAL CAR
IINDEX
150
145-176 LINEA 1ed GB 5-09-2008 9:22 Pagina 151
REFITTING THE
AND CONTROLS
DASHBOARD
STANDARD WHEEL
Following the procedure described previ-
ously, raise the car and remove the spare
wheel.
DEVICES
SAFETY
CORRECT USE
OF THE CAR
F0R0156m F0R0157m
fig. 5 fig. 6
❒ for versions with wheel cap, remove the ❒ fit the wheel cap making the crescent
wheel cap after loosening the 3 fastening hole coincide with the bolt you have fit-
bolts and finally loosen the fourth bolt ted using the wrench;
LIGHTS AND
MESSAGES
WARNING
L-fig. 5 and extract the wheel; ❒ tighten the fastening bolts;
❒ make sure the contact surfaces be-
tween spare wheel and hub are clean ❒ turn the jack handle L-fig. 4 to lower
so that the fastening bolts will not come the car and remove the jack;
EMERGENCY
loose; ❒ use the wrench provided to fasten the
IN AN
❒ fit the spare wheel by inserting the first bolts completely in a criss-cross fashion
bolt for two threads into the hole clos- as shown in fig. 6;
est to the inflation valve; ❒ if replacing a wheel with alloy rim, stove
SPECIFICATIONS MAINTENANCE
it temporarily into the spare wheel
CAR
compartment with the cosmetic side
facing upwards.
TECHNICAL
INDEX
151
145-176 LINEA 1ed GB 5-09-2008 9:22 Pagina 152
Versions with steel rims Versions with alloy rims When you have finished
AND CONTROLS
DASHBOARD
Proceed as follows: Proceed as follows: ❒ stow the spare wheel in the space pro-
vided in the boot;
❒ make sure the contact surfaces be- ❒ insert the wheel on the hub and using
tween spare wheel and hub are clean the wrench provided tighten the bolts; ❒ fit the jack partially open in its box
so that the fastening bolts will not come C-fig. 2 forcing it lightly to prevent it
❒ lower the car and remove the jack;
DEVICES
SAFETY
fastening bolts;
❒ lower the car and remove the jack;
❒ using the wrench provided, fully tight-
EMERGENCY
IN AN
152
145-176 LINEA 1ed GB 5-09-2008 9:22 Pagina 153
AND CONTROLS
DASHBOARD
FIX & GO automatic
The Fix & Go automatic quick tyre repair
kit is placed in the boot under the mat.
DEVICES
SAFETY
The kit fig. 7 includes:
❒ cylinder A containing sealant and fitted
with:
CORRECT USE
OF THE CAR
F0R0158m F0R0159m
fig. 7 fig. 8
– filling pipe B;
– an adhesive label C with the mes- ❒ a pair of protection gloves located in The quick repair kit also contains a screw-
sage “max. 80 km/h” to be apply in the side space of the compressor; driver and a tow ring.
a position clearly visible by the dri-
LIGHTS AND
❒ adapters for inflating different elements.
MESSAGES
WARNING
ver (on the dashboard) after repair-
ing the tyre;
❒ instruction booklet (see fig. 8), to be WARNING
used for prompt and proper use of the Hand over the instruction
EMERGENCY
quick repair kit and to be then handed booklet to the personnel
IN AN
to the personnel charged with handling charged with treating the tyre re-
the treated tyre; paired with the kit.
❒ compressor D-fig. 7 including gauge
SPECIFICATIONS MAINTENANCE
and connections;
TECHNICAL
INDEX CAR
153
145-176 LINEA 1ed GB 5-09-2008 9:22 Pagina 154
IMPORTANT INFORMATION:
AND CONTROLS WARNING
DASHBOARD
In the event of a puncture
caused by foreign bodies, the The damage cannot be re- The sealing fluid of the quick tyre repair
kit may be used to repair paired with the kit if the kit is effective with external temperatures
tyres showing damages on the wheel rim is damaged (deformation between -20 °C and +50 °C.
track or shoulder up to max 4 mm di- of the channel causing leakage of air).
ameter. The sealing fluid will expire.
Do not remove the foreign body
DEVICES
SAFETY
WARNING
CORRECT USE
WARNING
OF THE CAR
154
145-176 LINEA 1ed GB 5-09-2008 9:22 Pagina 155
AND CONTROLS
WARNING
DASHBOARD
Replace the cylinder contain-
The cylinder contains ethyl ing the sealant after the ex-
glycol. Contains latex: may piration date. Dispose of the
cause an allergic reaction. Harmful if cylinder and the sealant liq-
swallowed. Irritant for the eye. May uid properly. Dispose according to the
cause sensitization by inhalation or national and local laws in force.
DEVICES
SAFETY
contact. Avoid contact with your eyes,
skin and clothes. In the event of con-
tact, wash immediately with plenty of
CORRECT USE
water. Do not induce vomit if swal-
OF THE CAR
F0R0109m
fig. 9
lowed. Rinse your mouth and drink
plenty of water. Call a doctor imme-
diately. Keep away from children. The INFLATION PROCEDURE
product must not be used by asth-
LIGHTS AND
MESSAGES
matics. Do not breath in the vapours
WARNING
during insertion and suction. Call a WARNING
doctor immediately if allergic reactions Put on the protection gloves
are noted. Store the cylinder in the provided together with quick
specific compartment, away from
EMERGENCY
tyre repair kit.
sources of heat. The sealing fluid will
IN AN
expire.
SPECIFICATIONS MAINTENANCE
tyre valve cap, extract the flexible filler
CAR
tube A-fig. 9 and fasten the ring B on-
to the tyre valve;
TECHNICAL
INDEX
155
145-176 LINEA 1ed GB 5-09-2008 9:22 Pagina 156
WARNING
Apply the adhesive label in a
position clearly visible by the
CORRECT USE
OF THE CAR
F0R0160m F0R0110m
fig. 10 fig. 12
driver as a reminder that the tyre has
been treated with the quick repair kit.
For a more accurate reading, check Drive carefully, particularly on bends.
pressure gauge F-fig. 10 with the Do not exceed 80 km/h. Do not ac-
compressor off;
LIGHTS AND
❒ make sure that switch D-fig. 10 of the ble after 5 minutes to reach at least 1.8
CAR
compressor is in position 0 (off), start bar, do not start driving since the tyre WARNING
the engine, plug into the nearest sock- is excessively damaged and the quick Stop if the pressure has
et E-fig. 11 and operate the compres- tyre repair kit cannot guarantee suit- dropped to less than 1.8
sor turning switch D-fig. 10 to position able sealing, contact Fiat Dealership; bars: the Fix & Go automatic quick
TECHNICAL
I (on). Inflate the tyre to the pressure repair kit cannot work properly be-
specified in the “Inflation pressure” cause the tyre is excessively damaged.
paragraph, “Technical Specifications” Go to a Fiat Dealership.
chapter.
IINDEX
156
145-176 LINEA 1ed GB 5-09-2008 9:22 Pagina 157
AND CONTROLS
DASHBOARD
store proper pressure (with engine
running and handbrake on) and restart;
❒ drive with the utmost care to the near-
est Fiat Dealership.
DEVICES
SAFETY
WARNING
CORRECT USE
OF THE CAR
F0R0111m F0R0161m
Remember to inform the fig. 13 fig. 14
workshop that the tyre has
been treated with a quick repair kit. FOR CHECKING AND CYLINDER REPLACEMENT
Give the instruction booklet to the RESTORING PRESSURE ONLY PROCEDURE
tyre repair workshop personnel.
LIGHTS AND
MESSAGES
WARNING
The compressor may also be used for To replace the cylinder proceed as fol-
restoring pressure only. Release coupling lows:
A-fig. 14 and connect directly to the tyre
valve fig. 13. In this way, the cylinder will ❒ release connection A-fig. 14;
not be connected to the compressor and ❒ turn anticlockwise the cylinder to re-
EMERGENCY
IN AN
no sealant will be injected. place and raise it;
❒ fit the new cylinder and turn it clock-
wise;
SPECIFICATIONS MAINTENANCE
❒ connect connection A to the cylinder
CAR
and fit the transparent tube B into the
proper space.
TECHNICAL
INDEX
157
145-176 LINEA 1ed GB 5-09-2008 9:22 Pagina 158
AND CONTROLS
DASHBOARD
WHEN NEEDING TO WARNING
CHANGE A BULB Modifications or repairs to
the electrical system (elec-
tronic control units) that are not car-
GENERAL INSTRUCTIONS ried out properly or do not take the
technical specifications of the system
DEVICES
the corresponding fuse is intact before into account can cause malfunctions
replacing it: refer to the “If a fuse leading to the risk of fire.
blows” paragraph in this chapter for
CORRECT USE
OF THE CAR
fuse location.
❒ before changing a bulb check the con-
tacts for oxidation; WARNING
❒ burnt bulbs must be replaced by others Halogen bulbs contain pres-
LIGHTS AND
MESSAGES
WARNING
dled holding the metallic part this does not indicate a fault and is caused
by low temperature and the degree of hu- A All glass bulb: clipped into place. Pull
CAR
Various types of bulbs are fitted to your car: clip from the corresponding seat to
remove the lamp.
158
145-176 LINEA 1ed GB 5-09-2008 9:22 Pagina 159
AND CONTROLS
DASHBOARD
Main beam headlights D H1U55W 55W
Dipped beam headlights D H755W 55W
Front sidelights A W5W 5W
DEVICES
SAFETY
Front fog lights (where provided) – H1U55W 55W
Front direction indicators B PY21W 21W
CORRECT USE
OF THE CAR
Side direction indicators A WY5W 5W
Rear direction indicators B Y21W 21W
Side/taillights B R5W 5W
LIGHTS AND
MESSAGES
WARNING
Brake lights B P21W 21W
Third brake light (additional brake light) B 5W 5W
Reversing light – P21W
EMERGENCY
21W
IN AN
Rear fog lights – P21W 21W
Number plate light A W5W 5W
SPECIFICATIONS MAINTENANCE
Front ceiling light with spot lights C 10W x 2 10W
CAR
Rear ceiling light with movable lens C 10W 10W
Boot light A W5W 5W
TECHNICAL
Puddle light C W5W 5W
Courtesy light C 1.2W x 2 1.2W
Courtesy light C C5W 5W
INDEX
Oddments compartment courtesy light C C5W 5W
159
145-176 LINEA 1ed GB 5-09-2008 9:22 Pagina 160
AND CONTROLS
DASHBOARD
IF AN EXTERIOR LIGHT A
BURNS OUT
For the type of bulb and power rating, see
“When needing to change a bulb”.
DEVICES
SAFETY
C B D
CORRECT USE
OF THE CAR
F0R0220m F0R0221m
fig. 16 fig. 17
The front light clusters contain sidelights, ❒ remove the clipped-on cover;
dipped beam, main beam and direction in-
dicator bulbs. ❒ press tabs B and remove the bulb
holder;
The bulbs are arranged inside the light unit
EMERGENCY
A main beam ❒ refit the bulb holder and refit the cap
and check that it is locked properly.
B side lights
SPECIFICATIONS MAINTENANCE
D direction indicators.
TECHNICAL
IINDEX
160
145-176 LINEA 1ed GB 5-09-2008 9:22 Pagina 161
AND CONTROLS
DASHBOARD
DEVICES
SAFETY
CORRECT USE
OF THE CAR
F0R0222m F0R0223m F0R0224m
fig. 18 fig. 19 fig. 19/a
LIGHTS AND
Front fig. 19/a
MESSAGES
WARNING
To change the bulb, proceed as follows: To change the bulb, proceed as follows:
❒ remove the clipped-on cover; ❒ remove the clipped-on cover; To change the bulb, proceed as follows:
❒ disconnect the central electric connec- ❒ disconnect the central electric connec- ❒ steer the right/left wheel outwards as
shown in the figure;
EMERGENCY
tor and release the bulb holder catch; tor and release the bulb holder catch;
IN AN
❒ remove the bulb B and replace it; ❒ remove the bulb B and replace it; ❒ turn the catch as shown by the arrow,
then use the lid;
❒ fit the new bulb, making the outlines of ❒ refit the new bulb;
the metallic part coincide with the ❒ remove the bulb holder cover by turn-
SPECIFICATIONS MAINTENANCE
grooves on the reflector; ❒ refit the bulb holder catch and reconnect ing it anticlockwise;
the electrical connector;
CAR
❒ refit the bulb holder catch and reconnect
the electrical connector; ❒ refit the protection and check that it
is correctly locked.
❒ refit the protection and check that it
TECHNICAL
is correctly locked.
INDEX
161
145-176 LINEA 1ed GB 5-09-2008 9:22 Pagina 162
AND CONTROLS A B C
DASHBOARD
DEVICES
SAFETY
E D
CORRECT USE
OF THE CAR
❒ extract the bulb D by pressing it slight- FRONT FOG LIGHTS REAR LIGHT CLUSTERS
ly and turning it anticlockwise (bayonet (where provided) fig. 22-23
locking) then replace it;
LIGHTS AND
MESSAGES
vice.
IN AN
B taillights
Side fig. 20 C rear fog lights
To change the bulb, proceed as follows: D direction indicators
SPECIFICATIONS MAINTENANCE
E reversing light.
❒ work on the lens A to compress the in-
CAR
162
145-176 LINEA 1ed GB 5-09-2008 9:22 Pagina 163
AND CONTROLS
DASHBOARD
DEVICES
SAFETY
CORRECT USE
OF THE CAR
F0R0229m F0R0230m
fig. 23/b fig. 24
LIGHTS AND
MESSAGES
WARNING
❒ disconnect the central electric connector and pull the lens unit out-
wards;
❒ release the clips F and extract the bulb holders;
EMERGENCY
❒ remove the bulb to replace A, B, C or D pushing it slightly and
IN AN
turning it anticlockwise (bayonet-type bulb) and replace it;
❒ refit the bulb holder and refasten the clips F;
SPECIFICATIONS MAINTENANCE
❒ to replace the rear fog light, release the clips H-fig. 24, remove
the protection and replace the bayonet bulb.
CAR
❒ reconnect the electrical connector, reposition the cluster correct-
ly on the body and then tighten the fastening screws G.
TECHNICAL
fig. 23/a F0R0228m
INDEX
163
145-176 LINEA 1ed GB 5-09-2008 9:22 Pagina 164
AND CONTROLS
DASHBOARD
DEVICES
SAFETY
CORRECT USE
OF THE CAR
follows:
❒ open the tailgate; ❒ remove and replace the bulbs fig. 26.
❒ disconnect the electric connector
A-fig. 25;
EMERGENCY
IN AN
F0R0124m
fig. 28
SPECIFICATIONS MAINTENANCE
164
145-176 LINEA 1ed GB 5-09-2008 9:22 Pagina 165
IF AN INTERIOR LIGHT
AND CONTROLS
DASHBOARD
BURNS OUT
For the type of bulb and power rating, see
“When needing to change a bulb”.
DEVICES
SAFETY
FRONT CEILING LIGHT
To replace the bulbs proceed as follows:
CORRECT USE
OF THE CAR
❒ work in the points shown by the ar-
F0R0115m F0R0116m
fig. 29 fig. 31
rows and remove light A-fig. 29;
❒ open the protection lid B-fig. 30;
❒ replace bulbs C releasing them from the
LIGHTS AND
MESSAGES
WARNING
side contacts; make sure that new bulbs
are correctly clamped between contacts;
❒ re-close the lid B-fig. 30 and secure light
A-fig. 29 into its housing locking it
EMERGENCY
properly.
IN AN
F0R0117m F0R0118m
fig. 30 fig. 32
SPECIFICATIONS MAINTENANCE
REAR CEILING LIGHT ❒ change the bulb F-fig. 32 releasing it
CAR
(where provided) from the side contacts and making sure
the new bulb is correctly fastened be-
To replace the bulbs proceed as follows: tween the contacts;
❒ work in the points shown by the ar-
TECHNICAL
❒ re-close the protection lid E-fig. 32
rows and remove light D-fig. 31; and secure light D-fig. 31 into its hous-
❒ open the protection lid E-fig. 32; ing locking it properly.
INDEX
165
145-176 LINEA 1ed GB 5-09-2008 9:22 Pagina 166
AND CONTROLS
DASHBOARD
DEVICES
SAFETY
CORRECT USE
OF THE CAR
❒ open the mirror cover A; ❒ open the tailgate; To change the bulb, proceed as follows:
❒ extract lens B levering in the points ❒ remove the light A levering in the point ❒ remove the light by pressing clip A-
shown by the arrow; shown by the arrow; fig. 35 with a screwdriver;
❒ open the protection B and replace the
EMERGENCY
snap-fitted bulb;
seat, extract the clipped-on bulb and re-
place it; ❒ re-close the protective cover B on the
lens;
❒ correctly reposition the bulb holder C
SPECIFICATIONS MAINTENANCE
❒ refit the light B inserting it in its cor- then on the other until it clicks into
rect position firstly on one end and place.
then on the other until it clicks into
TECHNICAL
place.
IINDEX
166
145-176 LINEA 1ed GB 5-09-2008 9:22 Pagina 167
AND CONTROLS
DASHBOARD
DEVICES
SAFETY
CORRECT USE
OF THE CAR
F0R0121m F0R0303m F0R0304m
fig. 36 fig. 37 fig. 38
❒ press the bulb protection cover sides ODDMENTS COMPARTMENT ❒ replace the bulb B-fig. 38 releasing it
B-fig. 36 on the two fastening pins and COURTESY LIGHT from the side contacts and making sure
turn it; the new bulb is correctly fastened be-
LIGHTS AND
(where provided) figs. 37-38
MESSAGES
WARNING
tween the actual contacts;
❒ replace the snap-fitted bulb C-fig. 36; To change the bulb, proceed as follows:
❒ refit the courtesy light A-fig.37 in its
❒ refit bulb protection cover fitting the ❒ work at the points shown by the ar- housing making sure that it is secure.
two fastening pins; rows and remove the courtesy light A-
EMERGENCY
❒ refit the ceiling light inserting first end fig. 37;
IN AN
D-fig. 35 and then pressing the other
end until hearing the locking click of the
clip.
SPECIFICATIONS MAINTENANCE
TECHNICAL
INDEX CAR
167
145-176 LINEA 1ed GB 5-09-2008 9:22 Pagina 168
AND CONTROLS
DASHBOARD
IF A FUSE BLOWS WARNING
Go to a Fiat Dealership if a
GENERAL general protection fuse
blows (MEGA-FUSE, MIDI-FUSE,
The fuse is a protective device for the MAXI-FUSE).
electric system: it comes into action (i.e.
DEVICES
SAFETY
WARNING
OF THE CAR
F0R0122m
fuse when a device does not work: the fig. 39
conducting element A-fig. 39 must not be Remove the key from the ig-
interrupted. If it is, replace the blown fuse nition switch and switch off
with another with the same amperage Never replace a blown fuse all loads before replacing a fuse.
(same colour). with metallic wires or other
LIGHTS AND
MESSAGES
WARNING
material.
B undamaged fuse
C fuse with damaged filament.
WARNING
EMERGENCY
IN AN
a Fiat Dealership.
TECHNICAL CAR
IINDEX
168
145-176 LINEA 1ed GB 5-09-2008 9:22 Pagina 169
FUSE LOCATION
AND CONTROLS
DASHBOARD
The fuses are grouped in three units on
the dashboard, in the engine compartment
and on the positive battery terminal.
DEVICES
Fuse box on the dashboard fig. 41
SAFETY
To gain access to the fuses in the fuse box
on the dashboard, loosen the fastening
screws A-fig. 40 and remove the cover.
CORRECT USE
OF THE CAR
F0R0125m
fig. 40
LIGHTS AND
MESSAGES
WARNING
F34 F48 F49 F35 F13
EMERGENCY
IN AN
F46 F33 F37 F42 F12
SPECIFICATIONS MAINTENANCE
CAR
F52 F41 F43 F40 F44
TECHNICAL
INDEX
F0R0126m
fig. 41
169
145-176 LINEA 1ed GB 5-09-2008 9:22 Pagina 170
F0R0127m
fig. 42
LIGHTS AND
MESSAGES
WARNING
EMERGENCY
IN AN
SPECIFICATIONS MAINTENANCE
TECHNICAL CAR
IINDEX
F0R0128m
fig. 43
170
145-176 LINEA 1ed GB 5-09-2008 9:22 Pagina 171
FUSE TABLE
AND CONTROLS
DASHBOARD
Fuse box on dashboard fig. 41
DEVICES
SAFETY
Right dipped beam headlight F12 7.5
Left dipped beam headlight, headlight corrector F13 7.5
CORRECT USE
OF THE CAR
INT/A for relay coils (T08, T17) in engine compartment fuse box and body F31 7.5
computer node
Heated Seats F32 15
LIGHTS AND
MESSAGES
WARNING
Power windows control unit (left rear window motor) F33 20
Power windows control unit (right rear window motor) F34 20
EMERGENCY
+15 reversing lights, brake lights control NC, air mass meter, glow plug pre-heating F35 7.5
IN AN
unit, water in diesel fuel sensor, tachometer generator, level sensor 2
Power window unit (+30 for electronics) F36 7.5
SPECIFICATIONS MAINTENANCE
+15 instrument panel, NA brake lights control F37 7.5
CAR
Body computer node F38 20
Radio node, climate control node, node Blue&Me F39 10
TECHNICAL
Heated rear window F40 30
Mirror defrosters F41 7.5
+15 brake system F42 7.5
INDEX
Windscreen wiper control (two-way pump) F43 20
171
145-176 LINEA 1ed GB 5-09-2008 9:22 Pagina 172
172
145-176 LINEA 1ed GB 5-09-2008 9:22 Pagina 173
AND CONTROLS
DASHBOARD
LOADS FUSE AMPERES
Horn F10 10
DEVICES
SAFETY
Engine control system secondary loads F11 10
Right main beam headlight F14 7.5
CORRECT USE
Left beam headlight F15 7.5
OF THE CAR
Engine control system primary loads F17 10
Engine control unit F18 10
LIGHTS AND
MESSAGES
WARNING
Conditioner compressor F19 7.5
Fuel pump F21 15
Engine control system primary loads (injectors, ignition coils) F22 15
EMERGENCY
IN AN
Windscreen wiper motor F23 20
Spare F24 10
SPECIFICATIONS MAINTENANCE
Fog lights F30 15
TECHNICAL
INDEX CAR
173
145-176 LINEA 1ed GB 5-09-2008 9:22 Pagina 174
IF THE BATTERY IS FLAT ❒ when you have finished, turn the charg-
AND CONTROLS WARNING
DASHBOARD
er off before disconnecting the battery;
Battery fluid is poisonous
IMPORTANT The battery recharging pro- ❒ reconnect battery negative terminal. and corrosive: avoid contact
cedure is provided as an example only. with your skin and eyes. The battery
You are recommended to go to a Fiat recharging operation must be per-
Dealership to have this operation per- formed in a ventilated placed away
DEVICES
SAFETY
174
145-176 LINEA 1ed GB 5-09-2008 9:22 Pagina 175
AND CONTROLS
DASHBOARD
If the car is to be lifted, go to a Fiat Deal- The tow ring provided with the car is
ership which is equipped with the arm housed in the tool box under the boot
hoist or workshop lift. mat.
DEVICES
SAFETY
WARNING
The front and rear tow hooks
CORRECT USE
OF THE CAR
F0R0129m
fig. 42
should only be used on the
roads for emergency operations. Tow-
Lift the car exclusively by positioning the ing is permitted for short journies us-
jack arms or the shop jack in the points ing the special device that conforms to
shown in the figure. the highway code (rigid bar) to move
LIGHTS AND
MESSAGES
WARNING
the vehicle onto the road in prepara-
tion for towing or transportation on
a special vehicle.
The hooks should NOT be used for re-
EMERGENCY
covering the vehicle away from the
IN AN
road or where there are obstacles
and/or for towing using cables or oth-
er non rigid devices. With regard to the
above conditions, towing should take
SPECIFICATIONS MAINTENANCE
place with the two vehicles (the one
CAR
towing and the one being towed)
aligned as closely as possible along the
same centre line axis.
TECHNICAL
INDEX
175
145-176 LINEA 1ed GB 5-09-2008 9:22 Pagina 176
port;
❒ tighten the ring on the rear or front
threaded pin.
CORRECT USE
OF THE CAR
F0R0130m
fig. 43
WARNING
Release the steering wheel
WARNING lock before towing (see “Ig-
The power brakes and pow- nition device” in “Dashboard and con-
LIGHTS AND
MESSAGES
WARNING
176
177-200 LINEA 1ed GB 3-09-2008 17:31 Pagina 177
CAR MAINTENANCE
AND CONTROLS
DASHBOARD
SCHEDULED SERVICING ................................................ 178
SERVICE SCHEDULE
DEVICES
SAFETY
PETROL VERSIONS ............................................................. 179
SERVICE SCHEDULE
DIESEL VERSIONS ............................................................... 181
CORRECT USE
OF THE CAR
REGULAR INSPECTIONS ................................................. 183
DEMANDING USE OF THE CAR ................................... 183
CHECKING FLUID LEVELS................................................ 184
LIGHTS AND
MESSAGES
WARNING
AIR CLEANER ...................................................................... 190
POLLEN FILTER ................................................................... 190
BATTERY ................................................................................ 190
EMERGENCY
IN AN
WHEELS AND TYRES ......................................................... 193
RUBBER HOSES .................................................................... 194
SPECIFICATIONS MAINTENANCE
WINDSCREEN WIPERS...................................................... 194
CAR
BODYWORK ........................................................................ 196
INTERIORS ............................................................................ 198
TECHNICAL
INDEX
177
177-200 LINEA 1ed GB 3-09-2008 17:31 Pagina 178
AND CONTROLS
DASHBOARD
SCHEDULED SERVICING IMPORTANT Scheduled service coupons IMPORTANT You are advised to contact
are required by the manufacturer. Default Fiat Dealership in the event of any minor
Correct maintenance is essential for en- may cancel the warranty. operating faults, without waiting for the
suring long car life under the best condi- next service coupon.
Scheduled Servicing is performed by all
tions. Fiat Dealership, at pre-established times. If your car is used frequently for towing,
the interval between one service coupon
DEVICES
SAFETY
This is why Fiat has planned a series of If during each operation, in addition to the
checks and maintenance operations every and the other must be reduced.
ones programmed, the need arises for fur-
30,000 km. ther replacements or repairs, these may
Scheduled servicing will not however ful- be carried out only with the explicit agree-
CORRECT USE
OF THE CAR
check, etc.
IN AN
SPECIFICATIONS MAINTENANCE
TECHNICAL CAR
INDEX
178
177-200 LINEA 1ed GB 3-09-2008 17:31 Pagina 179
AND CONTROLS
DASHBOARD
Service coupons shall be performed every 30,000 km
Thousands of kilometres 30 60 90 120 150 180
DEVICES
SAFETY
Check tyre conditions/wear and adjust pressure if
required ● ● ● ● ● ●
Check light system operation (headlights, direction indicators,
CORRECT USE
hazard lights, boot lights, passenger compartment lights,
OF THE CAR
instrument panel warning lights, etc.) ● ● ● ● ● ●
Check windscreen wiper/washer operation ● ● ● ● ● ●
Check of conditions and wear of pads of front disk brakes ● ● ● ● ● ●
LIGHTS AND
MESSAGES
WARNING
Check of conditions and wear of pads of rear disk brakes
(T-JET version) ● ● ● ● ● ●
Check rear drum brake linings and wear ● ● ●
EMERGENCY
IN AN
Visually inspect conditions and integrity: bodywork,
underbody protection, pipes and hoses
(exhaust - fuel - brakes), rubber parts
(boots, sleeves, bushes, etc.) ● ● ● ● ● ●
SPECIFICATIONS MAINTENANCE
CAR
Check cleanness of locks, bonnet and boot and lever
cleanness and lubrication ● ● ● ● ● ●
TECHNICAL
Visually inspect accessory drive belt conditions ● ●
Replace accessory drive belt/s ●
● ● ● ● ● ●
INDEX
Check and adjust handbrake lever stroke, if required
Check and adjust tappet clearance, if required ● ● ●
179
177-200 LINEA 1ed GB 3-09-2008 17:31 Pagina 180
AND CONTROLS
DASHBOARD Thousands of kilometres 30 60 90 120 150 180
Check exhaust emissions ● ● ● ● ● ●
Replace air cleaner cartridge ● ● ●
Change spark plugs (❍) 1
● ● ● ● ● ●
DEVICES
SAFETY
Top up fluids
(engine coolant, brakes, battery, windscreen washer, etc.) ● ● ● ● ● ●
● ●
CORRECT USE
(*) Regardless of the km covered, the timing belt shall be replaced every 4 years for particularly demanding use
(cold climates, driving in the city, idling for a long time) or in any case every 5 years
SPECIFICATIONS MAINTENANCE
(❍) 1 For 1.4 T-JET version, in order to ensure correct operation and avoid significant damages to the engine, it is mandatory:
CAR
- to use spark plugs specifically certified for the T-JET engine only, of the same type and brand (see paragraph “Engine”);
- to replace the plugs as often as required by the Programmed Maintenance Plan;
- we recommend to refer to the Fiat Dealership
TECHNICAL
2 If the car is mainly used in cities or less than 10,000 km a year, change the engine oil and filter every 12 months.
INDEX
180
177-200 LINEA 1ed GB 3-09-2008 17:31 Pagina 181
AND CONTROLS
DASHBOARD
Service coupons shall be performed every 30,000 km
Thousands of kilometres 30 60 90 120 150 180
DEVICES
Check tyre conditions/wear and adjust pressure if
SAFETY
required ● ● ● ● ● ●
Check light system operation (headlights, direction indicators,
hazard lights, boot lights, passenger compartment lights,
CORRECT USE
OF THE CAR
instrument panel warning lights, etc.) ● ● ● ● ● ●
Check windscreen wiper/washer operation ● ● ● ● ● ●
Check the position/wear of the windscreen/rearscreen wiper blades ● ● ● ● ● ●
LIGHTS AND
MESSAGES
WARNING
Check front and rear (where provided) disk brake pad
conditions and wear ● ● ● ● ● ●
Check rear drum brake linings and wear ● ● ●
EMERGENCY
IN AN
Visually inspect conditions and integrity: bodywork,
underbody protection, pipes and hoses
(exhaust - fuel - brakes), rubber parts
(boots, sleeves, bushes, etc.) ● ● ● ● ● ●
SPECIFICATIONS MAINTENANCE
Check cleanness of locks, bonnet and boot and lever
CAR
cleanness and lubrication ● ● ● ● ● ●
Visually inspect accessory drive belt conditions ● ●
TECHNICAL
Replace accessory drive belt/s ●
Check and adjust handbrake lever stroke, if required ● ● ● ● ● ●
INDEX
181
177-200 LINEA 1ed GB 3-09-2008 17:31 Pagina 182
Top up fluids
(engine coolant, brakes, battery, windscreen washer, etc.) ● ● ● ● ● ●
CORRECT USE
Change engine oil and replace oil filter (or every 24 months) ● ● ● ● ● ●
Change brake fluid (or every 24 months) ● ● ●
Change pollen filter (or every 24 months) ● ● ● ● ● ●
EMERGENCY
IN AN
* Regardless of the mileage, the timing belt must be changed every 4 years for heavy-duty use (cold climates, town use, long periods of idling) or at least every 5
years.
SPECIFICATIONS MAINTENANCE
TECHNICAL CAR
INDEX
182
177-200 LINEA 1ed GB 3-09-2008 17:31 Pagina 183
AND CONTROLS
DASHBOARD
boot and lever cleanness and lubrica-
INSPECTIONS OF THE CAR tion;
Every 1,000 km or before long journeys, Should prevailing use of the car be under ❒ visually inspect the conditions of: en-
check and top up if required: one of the following specially heavy con- gine, gearbox, transmission, pipes and
hoses (exhaust - fuel - brakes), rubber
DEVICES
ditions:
SAFETY
❒ engine coolant fluid level; parts (boots, sleeves, bushes, etc.);
❒ trailer or caravan towing;
❒ brake fluid level; ❒ check battery charge and liquid level
❒ dusty roads; (electrolyte) (see paragraph “Charge
❒ brake fluid level;
CORRECT USE
OF THE CAR
❒ short distances (less than 7-8 km) re- level check” in chapter “Maintenance
❒ tyre pressure and conditions. peated and with external temperatures and care”);
❒ operation of lights (headlights, direction below zero; ❒ visually inspect the accessory drive belt
indicators, hazard lights, etc.); ❒ frequently idling engines or long dis- conditions;
LIGHTS AND
MESSAGES
WARNING
❒ operation of the windscreen wiper/ tance low speed driving (e.g. taxis or ❒ check pollen filter and replace, if re-
washer system, position and wear of door-to-door deliveries) or in case of quired;
the windscreen and rear window wiper a long term inactivity;
blades; ❒ check air cleaner and replace, if re-
❒ in cities; quired.
EMERGENCY
Every 3,000 km check the following and
IN AN
perform the following inspections more
top-up, if required:engine oil level. frequently than shown on the Service
You are recommended to use FL Schedule:
Selenia products, designed and produced
SPECIFICATIONS MAINTENANCE
❒ check front disk brake pad conditions
specifically for Fiat cars (see table “Ca- and wear;
CAR
pacities” in section “Technical specifica-
tions”).
TECHNICAL
INDEX
183
177-200 LINEA 1ed GB 3-09-2008 17:31 Pagina 184
AND CONTROLS
DASHBOARD
CHECKING FLUID
WARNING
Never smoke while working
DEVICES
SAFETY
6 4
SPECIFICATIONS MAINTENANCE
2
CAR
1. Engine coolant
TECHNICAL
2. Battery
3. Windscreen washer fluid
4. Brake fluid 3
1
5. Engine oil
INDEX
184
177-200 LINEA 1ed GB 3-09-2008 17:31 Pagina 185
1. Engine oil
AND CONTROLS
DASHBOARD
2. Engine coolant 6
3. Windscreen washer fluid 4 5
4. Brake fluid 1
5. Battery
DEVICES
SAFETY
6. Power steering fluid
2
CORRECT USE
3
OF THE CAR
1
LIGHTS AND
MESSAGES
WARNING
F0R0235m
fig. 3 - 1.3 Multijet version
EMERGENCY
IN AN
SPECIFICATIONS MAINTENANCE
TECHNICAL
INDEX CAR
F0R0301m
fig. 4 - 1.6 Multijet version
185
177-200 LINEA 1ed GB 3-09-2008 17:31 Pagina 186
F0R0134m F0R0135m
fig. 5 - 1.4 version fig. 7 - 1.3 Multijet version
under which the car is used.
IMPORTANT After adding or changing
the oil, let the engine turn over for a few
seconds and wait a few minutes after turn-
LIGHTS AND
MESSAGES
WARNING
WARNING
IN AN
MIN line, add oil through the filler A to attention to scarves, ties and other
Check the oil level a few minutes (about reach the MAX line.
5) after the engine has stopped, with the loose fitting garments: they could get
car parked on level ground. Oil level shall never exceed the MAX line. dragged by the moving parts.
TECHNICAL
186
177-200 LINEA 1ed GB 3-09-2008 17:31 Pagina 187
AND CONTROLS
DASHBOARD
ture of demineralised water and FL Sele-
nia PARAFLU UP through filler A of the
vessel until the level approaches the MAX
line.
The 50% concentration of PARAFLU UP
DEVICES
SAFETY
demineralised water protects from freez-
ing to a temperature of –35°C.
For particularly hard climate conditions, we
CORRECT USE
OF THE CAR
F0R0136m
fig. 9 recommend use of a 60% PARAFLU UP fig. 10 F0R0137m
LIGHTS AND
MESSAGES
WARNING
ready in the engine. To top up, remove the cap A.
PARAFLU UP antifreeze is
used in the engine cooling sys- Pour a mixture of water and TUTELA
tem. Use fluid of the same PROFESSIONAL SC 35, in the fol-
type contained in the cooling lowing concentrations:
EMERGENCY
Waste engine oil and oil filters system for top-ups. PARAFLU UP may
IN AN
contains substances which are not be mixed with other types of fluids. 30% TUTELA PROFESSIONAL
dangerous for the environ- If this accidentally occurs, do not start SC 35 and 70% water in summer.
ment. It is advisable to have the engine and contact a Fiat Dealer- 50% TUTELA PROFESSIONAL
oil and filters changed by a Fiat Deal- ship.
SPECIFICATIONS MAINTENANCE
SC 35 and 50% water in winter.
ership where they will be disposed of
CAR
according to the law. In case of temperatures below –20°C, use
undiluted TUTELA PROFESSIONAL
WARNING SC 35 fluid.
TECHNICAL
ENGINE COOLANT fig. 9 The cooling system is pres-
surised. If required, replace
The coolant level must be checked when the cap with an original spare part so
the engine is cold and must be between as not to compromise system effi-
the MIN and MAX lines on the vessel. ciency. Do not remove the cap from
INDEX
the vessel when the engine is hot: risk
of burns.
187
177-200 LINEA 1ed GB 3-09-2008 17:31 Pagina 188
Check level through the reservoir. NOTE Carefully clean the cap of reservoir
AND CONTROLS
DASHBOARD
A and the surrounding surface.
When opening the cap, make sure that no
WARNING dirt gets into the reservoir.
Do not travel with the wind- For topping up always use a funnel with
DEVICES
SAFETY
F0R0138m
fig. 11
used in areas with a high degree of at-
mospheric humidity, the fluid should be
BRAKE FLUID fig. 11 replaced at more frequent intervals than
WARNING
Release cap A: check that the liquid con- specified in the “Service schedule”.
LIGHTS AND
188
177-200 LINEA 1ed GB 3-09-2008 17:31 Pagina 189
AND CONTROLS
WARNING
DASHBOARD
Oil consumption is extremely
Brake fluid is poisonous and low; if another top-up should
highly corrosive. In the case be required after only a short
of accidental contact, wash the parts period of time, have the system checked
with water and mild soap and rinse for leakage at a Fiat Dealership.
with plenty of water. Call a doctor
DEVICES
SAFETY
immediately if swallowed.
CORRECT USE
OF THE CAR
fig. 12 - 1.4 T-JET version F0R0139m
LIGHTS AND
Symbol π on the contain in-
MESSAGES
WARNING
ground and the engine cold is between the id from coming into contact
dicates a synthetic brake flu- MIN and MAX lines on the reservoir with hot engine parts: the liquid is
id, which is different from a mineral body. The level may go over the MAX flammable.
fluid. Use of a mineral type fluid will line when the oil is hot.
damage the special rubber seals of If topping up is required, make sure the oil
EMERGENCY
the braking system beyond repair. you used has the same specifications as
IN AN
that already in the system.
SPECIFICATIONS MAINTENANCE
TECHNICAL
INDEX CAR
189
177-200 LINEA 1ed GB 3-09-2008 17:31 Pagina 190
AND CONTROLS
DASHBOARD
AIR CLEANER BATTERY
Have the air cleaner replaced by a Fiat The car fits a low-maintenance battery: no
Dealership. top-ups with distilled water are needed in
normal conditions of use.
DEVICES
SAFETY
F0R0140m
fig. 13
and take action according to the colour it
assumes.
IMPORTANT If the battery is not pro-
Refer to the table below. vided with the visual indicator to verify
electrolyte charge and level, control op-
LIGHTS AND
MESSAGES
WARNING
190
177-200 LINEA 1ed GB 3-09-2008 17:31 Pagina 191
AND CONTROLS
WARNING
DASHBOARD
Batteries contain very dan-
If required, replace the battery with a gen- Battery liquid is poisonous gerous substances for the en-
uine spare part having the same specifi- and corrosive. Avoid contact vironment. You are recom-
cations. with the skin and eyes. Keep naked mended to go to a Fiat Deal-
If a battery with different specifications is flames and sources of sparks away ership to have the battery replaced
from the battery: risk of fire and ex- where the old battery will be disposed
DEVICES
SAFETY
fitted, the service intervals given in the
“Service schedule” in this section will no plosion. of respecting both the environment and
longer apply. the laws in force.
Follow the battery manufacturer’s in-
CORRECT USE
OF THE CAR
structions for maintenance.
IMPORTANT Check the battery charge WARNING WARNING
once a year, preferably before the begin- Running the battery with an If the car is left for long peri-
ning to winter, to prevent freezing of the excessively low liquid level ods in very cold environ-
LIGHTS AND
electrolyte. Perform this inspection more ments, remove the battery and store it
MESSAGES
WARNING
will damage the battery beyond re-
frequently if the car is mainly used for pair and even cause an explosion. in a warm place to prevent freezing.
short distances or if electrical devices run-
ning with the key off are installed, partic-
ularly after-market.
EMERGENCY
IN AN
Incorrect assembly of electric
and electronic devices may
cause severe damage to your
SPECIFICATIONS MAINTENANCE
car. Go to a Fiat Dealership if
you want to install accessories (alarms,
CAR
mobile phone, etc.): they will suggest
the most suitable devices and advise
you if a higher capacity battery needs
to be installed.
TECHNICAL
INDEX
191
177-200 LINEA 1ed GB 3-09-2008 17:31 Pagina 192
AND CONTROLS
DASHBOARD
WARNING IMPORTANT A battery which is kept at The total intake of these systems (facto-
a charge of less than 50% (optical indica- ry and after-market) must be less than 0.6
Always wear the proper pro- tor with dark colour without green area mA x Ah (of the battery) as shown in the
tective eyewear when work- in the middle) for any length of time will following table:
ing on the battery or near it. be damaged by sulphation leading to a re-
duction in cranking power.
DEVICES
SAFETY
❒ switch off all lights inside the car: the car’s electric system is capable of with-
IN AN
car is however equipped with a system standing the load required, or whether it
which switches all internal lights off au- should be integrated with a more power-
tomatically; ful battery.
SPECIFICATIONS MAINTENANCE
❒ do not keep accessories (e.g. sound sys- Since these devices continue absorbing en-
ergy even when the ignition key is off, they
CAR
192
177-200 LINEA 1ed GB 3-09-2008 17:31 Pagina 193
AND CONTROLS
DASHBOARD
much. Cracks in the tread and on the
Check the pressure of each type, includ- sidewalls are a sign of ageing. Have the
ing the spare, approximately once every tyres checked by specialised personnel
two weeks and before starting a long jour- if they have been fitted for longer than
ney: this check must be performed with 6 years. Remember to check the spare
DEVICES
SAFETY
the tyre rested and cold. wheel very carefully;
It is normal for pressure to increase when ❒ In the case of replacement, always fit
the car is used. For the correct tyre in- new tyres, avoiding those of dubious
origin;
CORRECT USE
OF THE CAR
flation pressure, see “Wheels” in “Tech- fig. 14 F0R0141m
LIGHTS AND
MESSAGES
WARNING
A normal pressure: evenly worn tread. and violent knocks against the curb, and rear tyres, it is advisable to change
potholes or other obstacles if possible. them over every 10-15 thousand kilo-
B low pressure: tread particularly worn Long distances on rough roads may metres, keeping them on the same side
on the edges. damage the tyres; of the car so as not to reverse the di-
rection of rotation.
EMERGENCY
C excessive pressure: tread particularly ❒ check the tyres regularly for cuts on the
IN AN
worn in the middle. sides, swelling or irregular tread wear.
The tyres must be replaced when the Go to a Fiat Dealership if required.
tread is less than 1.6 mm thick. In all cas- ❒ do not over load your car: this may WARNING
SPECIFICATIONS MAINTENANCE
es, follow the laws in force in the coun- cause serious damage to wheels and Remember that the road
try where you are driving.
CAR
tyres; holding qualities of your car
❒ if a tyre is punctured, stop immediate- also depends on the correct inflation
ly and charge it to avoid damage to the pressure of the tyres.
tyre, the rim, suspensions and steering
TECHNICAL
system;
INDEX
193
177-200 LINEA 1ed GB 3-09-2008 17:31 Pagina 194
AND CONTROLS
DASHBOARD
WARNING RUBBER HOSES WINDSCREEN WIPER
Excessively low pressure will
cause overheating of the Carefully follow the information contained
in the “Service schedule” in this section BLADES
tyre and may cause severe tyre dam-
age. for maintenance of brake system and fuel Periodically clean the rubber part using
feed rubber hoses. special products; TUTELA PROFES-
DEVICES
SAFETY
sible leaks. Careful inspections are there- visable to replace them approximately
Do not exchange the tyres fore necessary. once a year.
from the left to the right of
the car and vice versa. A few simple precautions can reduce the
possibility of damage to the blades:
LIGHTS AND
MESSAGES
WARNING
on dry glass.
TECHNICAL
WARNING
Driving with worn wiper
blades is a serious hazard,
because visibility is reduced in bad
weather.
INDEX
194
177-200 LINEA 1ed GB 3-09-2008 17:31 Pagina 195
AND CONTROLS
DASHBOARD
❒ insert the blade fastening tabs in the
hole on the end of the arm;
❒ refit the arm with the blade on the
windscreen.
DEVICES
SAFETY
CORRECT USE
OF THE CAR
F0R0236m F0R0143m
fig. 15 fig. 16
LIGHTS AND
Windscreen washer fig. 16
MESSAGES
WARNING
How to remove the blade:
❒ raise the windscreen wiper arm A from If there is no jet of fluid, firstly check that
the windscreen; there is fluid in the reservoir: see “Check-
ing fluid levels” in this section).
❒ turn blade B 90° around pin C, locat-
EMERGENCY
Then check that the nozzle holes are not
IN AN
ed at the end of the wiper arm;
clogged, if necessary using a needle.
❒ press the blade locking tabs;
The windscreen jets are directed by ad-
❒ remove the blade from pin C. justing the angle of the nozzles.
SPECIFICATIONS MAINTENANCE
Fluid jets shall be directed at about 1/3
CAR
height from the window upper edge.
TECHNICAL
INDEX
195
177-200 LINEA 1ed GB 3-09-2008 17:31 Pagina 196
AND CONTROLS
DASHBOARD
BODYWORK These are the most important: BODY AND UNDERBODY
❒ paint products and systems which give WARRANTY
PROTECTION FROM the car particular resistance to corro- Your car is covered by warranty against
ATMOSPHERIC AGENTS sion and abrasion; perforation due to rust of any original el-
❒ use of galvanised (or pre-treated) steel ement of the structure or body.
The main causes of corrosion are the fol-
DEVICES
SAFETY
lowing: sheets, with high resistance to corro- For the general terms of this warranty, re-
sion; fer to Fiat Warranty Booklet.
❒ atmospheric pollution;
❒ spraying the underbody, engine com-
❒ salty air and humidity (coastal areas, or
CORRECT USE
sive action of wind-borne atmospheric points: under the doors, inside the
dust and sand and mud and gravel raised mudguard, along the edges, etc.
by other cars.
❒ use of “open” boxed sections to pre-
On your car, Fiat implemented the best vent condensation and pockets of mois-
EMERGENCY
196
177-200 LINEA 1ed GB 3-09-2008 17:31 Pagina 197
ADVICE FOR PRESERVING To correctly wash the car: Do not wash the car after it has been
AND CONTROLS
DASHBOARD
THE BODYWORK parked in the sun or when the engine is
❒ remove the aerial from the roof to pre- bonnet is hot: this could take the shine off
vent damage to it if the car is washed in the paint.
Paint an automatic system;
Paintwork does not only serve an aes- Exterior plastic parts must be cleaned in
❒ wash the body using a low pressure jet the same way as the rest of the car.
DEVICES
SAFETY
thetic purpose, but also protects the un- of water;
derlying sheet metal. Where possible, do not park under trees;
❒ wipe a sponge with a slightly soapy so- the resinous substance many species re-
Touch up abrasions and scratches immedi- lution over the bodywork, frequently
ately to prevent the formation of rust. On- lease give the paint a dull appearance and
CORRECT USE
rinsing with the sponge;
OF THE CAR
ly use genuine spare paint products for increase the possibility of triggering rust
touch-ups (see “Bodywork paint identifi- ❒ rinse well with water and dry with a jet processes.
cation plate” in the “Technical Specifica- of air or a chamois leather. IMPORTANT Bird droppings must be
tions” section). Dry the parts less in sight particularly care- washed off immediately and thoroughly as
LIGHTS AND
MESSAGES
WARNING
Normal maintenance of paintwork consists fully, such as the door frames and the the acid they contain is particularly ag-
in washing the car: the frequency depends headlight frames, where water may stag- gressive.
on the conditions and environment where nate more easily. It is a good idea to leave
the car is used. For example, it is advisable the car in the open for a while after wash-
ing it to give time for the water to evap-
EMERGENCY
to wash the car more often in areas with
orate.
IN AN
a high environmental pollution or on roads Detergents cause water pollu-
sprinkled with salt. tion. The car should be washed
in areas equipped for collect-
ing and purifying the liquid
SPECIFICATIONS MAINTENANCE
used in the washing process.
TECHNICAL
INDEX CAR
197
177-200 LINEA 1ed GB 3-09-2008 17:31 Pagina 198
AND CONTROLS
DASHBOARD Windows Front headlights INTERIORS
Use specific window cleaner products. IMPORTANT Never use aromatic sub-
stances (e.g.: petrol) or ketenes (e.g.: ace- Periodically check that water is not
Use also clean cloths to avoid scratching tone) for cleaning front headlight plastic trapped under the mats (due to water
the glass or damaging the transparency. lens. dripping off shoes, umbrellas, etc.) which
could cause oxidisation of the sheet
DEVICES
shop.
IN AN
198
177-200 LINEA 1ed GB 3-09-2008 17:31 Pagina 199
AND CONTROLS
WARNING
DASHBOARD
The fabric upholstery of your
Do not keep aerosol cans in car is designed to withstand It is advisable to clean interior parts with a
the car: risk of explosion. the normal wear and tear of moist cloth and a solution of water and mild
Aerosol cans must not be exposed to your car for a long time. Some soap. Use specific products for cleaning plas-
temperatures higher than 50°C. The precautions are however needed. Avoid tic, without solvents and specifically de-
temperature may raise well beyond prolonged rubbing against clothing ac- signed to prevent damage to the appearance
DEVICES
SAFETY
that figure when the car is left in the cessories, such as metal buckles, Velcro and colour of the treated parts to remove
sun. strips and the like, which by applying a grease and tough stains.
high pressure on the fabric in a small
area could cause the breakage of some IMPORTANT Never use spirit or petro-
CORRECT USE
OF THE CAR
threads and damage the upholstery. leum to clean the instrument panel.
CLEANING SEATS AND FABRIC
PARTS
LIGHTS AND
Remove dust with a soft brush or a vacu-
MESSAGES
WARNING
um cleaner. It is advisable to use a moist
brush on velvet upholstery.
Rub the seats with a sponge moistened
EMERGENCY
with a solution of water and neutral de-
IN AN
tergent.
SPECIFICATIONS MAINTENANCE
TECHNICAL
INDEX CAR
199
177-200 LINEA 1ed GB 3-09-2008 17:31 Pagina 200
GENUINE LEATHER STEERING If window cleaner accidentally drips onto IMPORTANT Be carefully when arranging
AND CONTROLS
DASHBOARD
WHEEL/GEAR LEVER KNOB the steering wheel or gear lever knob, a steering wheel lock device, where applic-
wipe away immediately and then wash the able, to prevent damaging the leather up-
These components must be cleaned with concerned area with mild soap and water. holstery by rubbing.
mild soap and water only.
Never use spirit and/or alcohol based
DEVICES
SAFETY
products.
Before using off-the-shelves products de-
signed for cleaning car interiors, make sure
CORRECT USE
EMERGENCY
IN AN
SPECIFICATIONS MAINTENANCE
TECHNICAL CAR
INDEX
200
201-221 LINEA 1ed GB 5-09-2008 9:24 Pagina 201
T E C H N I C A L S P E C I F I C AT I O N S
AND CONTROLS
DASHBOARD
IDENTIFICATION DATA ................................................. 202
ENGINE CODES - BODYWORK VERSIONS............... 204
DEVICES
SAFETY
ENGINE .................................................................................. 205
FUEL FEED/IGNITION ....................................................... 206
TRANSMISSION .................................................................. 207
CORRECT USE
OF THE CAR
BRAKES ................................................................................... 207
SUSPENSIONS....................................................................... 208
STEERING............................................................................... 208
LIGHTS AND
MESSAGES
WARNING
WHEELS .................................................................................. 209
DIMENSIONS......................................................................... 213
PERFORMANCE ................................................................... 214
EMERGENCY
IN AN
WEIGHTS ............................................................................... 215
CAPACITIES........................................................................... 216
SPECIFICATIONS MAINTENANCE
FLUIDS AND LUBRICANTS.............................................. 217
CAR
FUEL CONSUMPTION ....................................................... 219
CO2 EMISSIONS .................................................................. 221
TECHNICAL
INDEX
201
201-221 LINEA 1ed GB 5-09-2008 9:24 Pagina 202
AND CONTROLS
DASHBOARD
IDENTIFICATION DATA H Maximum vehicle weight on rear axle.
I Engine type.
Take note of the identification codes. The
following identification codes are printed L Body version code.
and shown on the plates: M Spare part code.
❒ Model plate.
DEVICES
SAFETY
F0R0247m
fig. 1
❒ Engine marking.
MODEL PLATE fig. 1
This is applied to the right-hand side of the
LIGHTS AND
MESSAGES
WARNING
D Chassis number.
E Maximum vehicle weight fully loaded.
SPECIFICATIONS MAINTENANCE
202
201-221 LINEA 1ed GB 5-09-2008 9:24 Pagina 203
ENGINE MARKING
AND CONTROLS
DASHBOARD
Engine marking is stamped on the cylinder
block and includes the model and the
chassis number.
DEVICES
SAFETY
CORRECT USE
OF THE CAR
F0R0145m F0R0146m
fig. 2 fig. 3
LIGHTS AND
MESSAGES
WARNING
This plate is applied to the tailgate and partment floor bed near the front right
shows the following data: seat.
A Paint manufacturer. ❒ car model (ZFA 323000);
❒ chassis number.
EMERGENCY
B Colour name.
IN AN
C Fiat colour code.
D Respray and touch up code.
SPECIFICATIONS MAINTENANCE
TECHNICAL
INDEX CAR
203
201-221 LINEA 1ed GB 5-09-2008 9:24 Pagina 204
AND CONTROLS
DASHBOARD
ENGINE CODES - BODYWORK VERSIONS
EMERGENCY
IN AN
SPECIFICATIONS MAINTENANCE
TECHNICAL CAR
INDEX
204
201-221 LINEA 1ed GB 5-09-2008 9:24 Pagina 205
ENGINE
AND CONTROLS
DASHBOARD
GENERAL 1.4 1.4 T-JET 1.3 Multijet 1.6 Multijet
Engine code 350A1000 198A4000 199A3000 198A3000
DEVICES
SAFETY
Cycle Otto Otto Diesel Diesel
Number and layout of cylinders 4 in line 4 in line 4 in line 4 in line
CORRECT USE
OF THE CAR
Piston bore and stroke mm 72 x 84 72,0 x 84,0 69.6 x 82 79.5 x 80.5
3
Total displacement cm 1368 1368 1248 1598
Compression ratio 11.1 ± 0.2 9.8 17.6 ± 0.4 16.5 ± 0.4
LIGHTS AND
MESSAGES
WARNING
Maximum power (EEC) kW 57 88 66 77
HP 77 120 90 105
corresponding ratio rpm 6000 5000 4000 4000
Maximum torque (EEC) Nm 115 206
EMERGENCY
200 290
kgm 11.7
IN AN
21 20.3 29.6
corresponding ratio rpm 3000 1750 1750 1500
Spark plugs NGK NGK
– –
SPECIFICATIONS MAINTENANCE
ZKR7A-10 IKR9F8
CAR
Fuel Unleaded petrol 95 Unleaded petrol 95 Diesel fuel for motor Diesel fuel for motor
RON RON vehicles vehicles
(EN228 Specifications) (EN228 Specifications) (EN590 specifications) (EN590 specifications)
TECHNICAL
INDEX
205
201-221 LINEA 1ed GB 5-09-2008 9:24 Pagina 206
AND CONTROLS
DASHBOARD
FUEL FEED/IGNITION
WARNING
Modifications or repairs to the fuel feed system that are not carried out properly or do not take the system’s
technical specifications into account can cause malfunctions leading to the risk of fire.
EMERGENCY
IN AN
SPECIFICATIONS MAINTENANCE
TECHNICAL CAR
INDEX
206
201-221 LINEA 1ed GB 5-09-2008 9:24 Pagina 207
TRANSMISSION
AND CONTROLS
DASHBOARD
1.4 - 1.4 T-JET - 1.6 - 1.8 - 1.3 Multijet 1.6 Multijet
Gearbox Five forward gears plus reverse Six forward gears plus reverse
with synchronisers for forward gears with synchronisers for forward gears
DEVICES
SAFETY
Clutch Self-adjusting with pedal without idle stroke Self-adjusting with pedal without idle stroke
Drive Front Front
CORRECT USE
OF THE CAR
BRAKES
LIGHTS AND
MESSAGES
WARNING
1.4 - 1.4 T-JET - 1.6 - 1.8 - 1.3 Multijet - 1.6 Multijet
Service brakes:
EMERGENCY
IN AN
– front disk
– rear drum / disk (T-JET version and 1.6 Multijet)
SPECIFICATIONS MAINTENANCE
Parking brake controlled by hand lever, operating on rear brakes
CAR
IMPORTANT Water, ice and salt sprinkled on the roads may deposit on the brake disks reducing braking efficiency
the first time the brakes are applied.
TECHNICAL
INDEX
207
201-221 LINEA 1ed GB 5-09-2008 9:24 Pagina 208
AND CONTROLS
DASHBOARD
SUSPENSIONS
1.4 - 1.4 T-JET - 1.6 - 1.8 - 1.3 Multijet - 1.6 Multijet
STEERING
LIGHTS AND
MESSAGES
WARNING
208
201-221 LINEA 1ed GB 5-09-2008 9:24 Pagina 209
AND CONTROLS
DASHBOARD
Pressed steel rim Tubeless tyre.
RIMS AND TYRES
WHEEL GEOMETRY
Pressed steel or alloy rims. Tubeless ra-
dial carcass tyres. All approved tyres are Toe-in total front: 0.3 ± 1 mm
DEVICES
SAFETY
listed in the Log Book. Toe-in total rear: 1.7 ± 0.5 mm
IMPORTANT In the event of discrepan- The values refer to the car in running or-
cies between the information provided on der.
CORRECT USE
OF THE CAR
F0R0147m
this “Owner’s handbook” and the “Log fig. 4
book”, consider the specifications shown
in the log book only. READING TYRE
Respect the prescribed size to ensure MARKINGS fig. 4
LIGHTS AND
MESSAGES
safety of the car in movement. Fit tyres
WARNING
Example: 185/65 R 15 88T
of the same make and type on all wheels.
185 = Nominal width (S, distance in mm
IMPORTANT Do not use inner tubes between sidewalls).
with Tubeless tyres.
EMERGENCY
65 = Height/width ratio (H/S) in per-
IN AN
centage.
R = Radial tyre.
15 = Rim diameter in inches (Ø).
SPECIFICATIONS MAINTENANCE
88 = Load rate (capacity).
CAR
T = Maximum speed rating.
TECHNICAL
INDEX
209
201-221 LINEA 1ed GB 5-09-2008 9:24 Pagina 210
210
201-221 LINEA 1ed GB 5-09-2008 9:24 Pagina 211
AND CONTROLS
DASHBOARD
Rim Tyre
6J X 15” - ET 44 185/65 R15 84T 6J X 15” - ET 44 185/65 R15 84T
195/60 R15 88H (❏) 195/60 R15 88H
1.4
DEVICES
SAFETY
6J X 16” - ET 41 195/55 R16 87H (❍) 6J X 15” - ET 44 185/65 R15 84T (**)
CORRECT USE
1.4 T-JET
OF THE CAR
1.3 Multijet
6J X 16” - ET 41 195/55 R16 87H (❍) 6J X 15” - ET 44 185/65 R15 84T (**)
1.6 Multijet
6.5J X 17” - ET 41 205/45 R17 88V (*) (▲) 6J X 15” - ET 44 185/65 R15 84T (**)
LIGHTS AND
MESSAGES
WARNING
(❏) Alloy rim
(❍) Optional alloy rim for versions/markets where provided
EMERGENCY
(*) Not snow chains
IN AN
(▲) Optional tyre for versions/markets where provided
(**) Using this spare wheel, vehicle max speed is 80 km/h
SPECIFICATIONS MAINTENANCE
TECHNICAL
INDEX CAR
211
201-221 LINEA 1ed GB 5-09-2008 9:24 Pagina 212
EMERGENCY
IN AN
SPECIFICATIONS MAINTENANCE
TECHNICAL CAR
INDEX
212
201-221 LINEA 1ed GB 5-09-2008 9:24 Pagina 213
DIMENSIONS
AND CONTROLS
DASHBOARD
Dimensions are expressed in mm and re-
fer to the vehicle fitted with standard
tyres.
DEVICES
SAFETY
The height refers to the unladen vehicle.
Boot volume
CORRECT USE
Unladen boot volume
OF THE CAR
(V.D.A. standards) ...................... 500 dm3
Boot capacity with rear
seat folded..................................... 870 dm3
LIGHTS AND
MESSAGES
WARNING
EMERGENCY
IN AN
fig. 5
SPECIFICATIONS MAINTENANCE
F0R0237m
CAR
Versions A B C D E F G H
TECHNICAL
4560 928 2603 1029 1494/1487 (*) 1467/1471 (❏) 1946.21 1482.5/1483.5 (❏)
1.4 T-JET
1.6 Multijet
INDEX
(*) With lower trim for versions/markets where provided
(❏) Full load
213
201-221 LINEA 1ed GB 5-09-2008 9:24 Pagina 214
AND CONTROLS
DASHBOARD
PERFORMANCE
Top admitted speed after initial car use in km/h.
EMERGENCY
IN AN
SPECIFICATIONS MAINTENANCE
TECHNICAL CAR
INDEX
214
201-221 LINEA 1ed GB 5-09-2008 9:24 Pagina 215
WEIGHTS
AND CONTROLS
DASHBOARD
Weights (kg) 1.4 1.4 T-JET 1.3 Multijet 1.6 Multijet
Unladen weight
DEVICES
(with all liquids, fuel tank filled to
SAFETY
90 % and without optional equipment): 1160 1200 1185 1290
Payload (*) including the driver: 500 500 500 500
CORRECT USE
OF THE CAR
Maximum admitted loads (**)
– front axle: 1000 1000 1000 1000
– rear axle: 900 900 900 900
– total: 1660 1670 1685 1790
LIGHTS AND
MESSAGES
WARNING
Towable loads
– trailer with brakes: 1200 1200 1200 1200
– trailer without brakes: 500 500 500 500
EMERGENCY
Maximum load on roof:
IN AN
75 75 75 75
Maximum load on tow hitch
(trailer with brakes): 70 70 70 70
SPECIFICATIONS MAINTENANCE
CAR
(*) If special equipment is fitted (sunroof, tow hitch, etc.) the unladen car weight increases, thus reducing the specified payload.
(**) Loads not be exceeded. The driver is responsible for arranging the loads in the boot and/or on the roof so that they comply
with these limits.
TECHNICAL
INDEX
215
201-221 LINEA 1ed GB 5-09-2008 9:24 Pagina 216
AND CONTROLS
DASHBOARD
CAPACITIES
1.4 1.4 1.3 1.6 Specified fuels and
T-JET Multijet Multijet genuine lubricants
Fuel tank: litres 45 45 – Unleaded petrol with no less than
DEVICES
SAFETY
– SELENIA K P.E.
WARNING
Hydraulic brake circuit: kg 0.4 / 0.5 (*) 0.46 / 0.56 (*) 0.4 / 0.5 (*) 0.4 / 0.5 (*) TUTELA TOP 4
Windscreen washer Mixture of water and
TECHNICAL
216
201-221 LINEA 1ed GB 5-09-2008 9:24 Pagina 217
AND CONTROLS
DASHBOARD
RECOMMENDED PRODUCTS AND SPECIFICATIONS
DEVICES
SAFETY
for correct car operation lubricants frequency
CORRECT USE
OF THE CAR
Lubricants for SAE 5W-40 ACEA A3/B3 grade totally SELENIA K According to
petrol engines synthetic lubricant. Contractual Technical Service Schedule
Qualification FIAT 9.55535-M2 Reference N° F214.I05
LIGHTS AND
MESSAGES
WARNING
Lubricants for Synthetic base lubricants SAE 5W-40 grade. SELENIA WR According to
diesel engines Qualification FIAT 9.55535-N2 Contractual Technical Service Schedule
Reference N° F515.D06
EMERGENCY
IN AN
For diesel engines, in the event of emergencies when genuine products are not available, lubricants providing at least ACEA B4
SPECIFICATIONS MAINTENANCE
performance are allowed; in that case, engine best performance is not guaranteed; we recommend to have it replaced as soon as
CAR
possible with the recommended lubricants by the Fiat Dealership.
The use of products with specifications below ACEA A3/B3 standards for petrol engines and ACEA B4 standards for diesel engines
could cause damage to the engine not covered under the warranty.
TECHNICAL
INDEX
217
201-221 LINEA 1ed GB 5-09-2008 9:24 Pagina 218
Reference N° F108.F02
SAFETY
versions)
Synthetic-based oil, grade SAE 75W-85. TUTELA CAR Mechanical gearbox
Qualification FIAT 9.55550-MX3 TECHNYX and differential
Contractual Technical (petrol and 1.3 Multijet
CORRECT USE
Reference N° F010.B05
OF THE CAR
Synthetic fluid FMVSS no. 116 DOT 4, ISO 4925 TUTELA TOP 4 Brake and clutch
Brake fluids SAE J1704, CUNA NC 956- 01. Contractual Technical hydraulic controls
Qualification FIAT 9.55597 Reference N° F001.A93
SPECIFICATIONS MAINTENANCE
radiators that passes CUNA NC 956-16, ASTM D 3306 specifications. Reference N° F101.M01 50% PARAFLU UP
Qualification FIAT 9.55523
Additive for diesel fuels with protective action TUTELA DIESEL ART To be mixed with diesel fuel
TECHNICAL
Fuel additivel for Diesel engines. Contractual Technical (25 cc per 10 litres)
Reference N°F601.L06
Mixture of alcohol, water and surfactants CUNA NC 956-II. TUTELA PROFES- To be used diluted or
Windscreen/ rear Qualification FIAT 9.55522 SIONAL SC 35 undiluted in windscreen/
window washer fluid Contractual Technical rear window washer/
Reference N° F201.D02 wiper systems
INDEX
(*) IMPORTANT Do not top up or mix with fluids having characteristics different from those specified.
When the vehicle is used under particularly harsh climate conditions, we recommend using a 60-40 mixture of PARAFLU UP and demineralised water.
218
201-221 LINEA 1ed GB 5-09-2008 9:24 Pagina 219
FUEL ❒ extra-urban cycle: frequent accelerat- IMPORTANT The type of route, traffic
AND CONTROLS
DASHBOARD
ing in all gears, simulating extraurban situations, weather conditions, driving
CONSUMPTION use of the car: speed varies between 0 style, general conditions of the car, trim
and 120 km/h; level/equipment/accessories, load, climate
The fuel consumption figures given in the control system, roof rack, other situations
table below are determined on the basis ❒ combined consumption: calculated that affect air drag may lead to different
weighing about 37% of urban cycle con-
DEVICES
of the homologation tests set down by
SAFETY
fuel consumption levels than those mea-
specific European Directives. sumption and about 63% of extraurban sured.
consumption.
The procedures below are followed for
measuring consumption:
CORRECT USE
OF THE CAR
❒ urban cycle: cold starting followed by
driving that simulates urban use of the
car;
LIGHTS AND
MESSAGES
WARNING
EMERGENCY
IN AN
SPECIFICATIONS MAINTENANCE
TECHNICAL
INDEX CAR
219
201-221 LINEA 1ed GB 5-09-2008 9:24 Pagina 220
EMERGENCY
IN AN
SPECIFICATIONS MAINTENANCE
TECHNICAL CAR
INDEX
220
201-221 LINEA 1ed GB 5-09-2008 9:24 Pagina 221
CO2 EMISSIONS
AND CONTROLS
DASHBOARD
The CO2 emission levels at the exhaust given in the following tables refer to combined consumption.
DEVICES
SAFETY
1.4 148
1.4 T-JET 157
CORRECT USE
OF THE CAR
1.3 Multijet 129
1.6 Multijet 131
LIGHTS AND
MESSAGES
WARNING
EMERGENCY
IN AN
SPECIFICATIONS MAINTENANCE
TECHNICAL
INDEX CAR
221
222-232 LINEA 1ed GB 9-09-2008 14:25 Pagina 222
AND CONTROLS
DASHBOARD
INDEX
ABS system.......................................... 92 Boot........................................................ 86 – front ................................................ 64
Accessories purchased – extension ........................................ 87 – puddle/door .................................. 74
DEVICES
SAFETY
– front................................................. 115
OF THE CAR
– recharging ...................................... 185 heavy conditions................................ 183 Correct use of the car ...................... 127
– replacing ......................................... 191 Card box - CD box............................. 72 Cruise Control..................................... 70
Bodywork Carrying children safely ..................... 109 Courtesy lights ..................................... 74
– maintenance .................................. 196 Ceiling lights.......................................... 72 – bulb replacement .......................... 174
INDEX
– version codes ............................... 204 – boot light ....................................... 66 – control button .............................. 74
Bonnet .................................................. 88 – courtesy ......................................... 66 Current outlet...................................... 73
222
222-232 LINEA 1ed GB 9-09-2008 14:25 Pagina 223
AND CONTROLS
5 125
DASHBOARD
– Left hand drive version ............... 5 ESP system ............................................ 93 Hazard lights ........................................ 75
Dashboard and controls..................... 4 External lights ...................................... 66 Head restraints
Dead lock device ................................. 77 – front ................................................ 45
Digital display ....................................... 18
Fiat CODE system ............................. 6
DEVICES
SAFETY
Fix & Go automatic ............................ 153 – rear................................................... 46
Dimensions .......................................... 213 Headlight washer
Flashing the headlights ....................... 66
Dipped beam headlights
Fluid levels ............................................ 184 – control ............................................ 61
MESSAGES
– rear bulb replacement ................. 162 – control ............................................ 72 Heated rear window ..................... 52-57
– side bulb replacement ................. 162 Front fog lights Heating and ventilation ...................... 49
Doors..................................................... 82 – bulb replacement .......................... 162
Identification data
EMERGENCY
– control button .............................. 75 .............................. 202
IN AN
Electrical socket ................................ 73 Fuel Ignition device....................................... 13
Engine – consumption................................... 229 In an emergency .................................. 145
– identification code ........................ 202 – cut-off switch.................................. 77 Instrument panel ................................. 14
SPECIFICATIONS MAINTENANCE
VEHICLE
– marking ........................................... 203 – level gauge....................................... 17 Instruments .......................................... 16
– technical data ................................ 205 Fuel cut-off switch ............................... 77 Interior fittings .................................... 78
Engine compartment Fuel filler cap ....................................... 102 Interiors ................................................ 198
– washing ........................................... 197 Fuel level gauge ................................... 17
TECHNICAL
Isofix (child restraint system) .......... 114
Engine coolant ...................................... 187 Fuses (replacement) ........................... 168
Engine coolant temperature gauge .. 17 Jack ........................................................ 148
Engine oil Gearbox Jacking the car ..................................... 175
– consumption .................................. 186 – using manual gearbox .................. 126
INDEX
– level check....................................... 186 Glass holder - can holder................... 72 Key with remote control ................ 8
– specifications ................................. 227 Glove box/oddment compartment.. 78 Key without remote control ........... 9
223
222-232 LINEA 1ed GB 9-09-2008 14:25 Pagina 224
Power socket ...................................... 73 – blades .............................................. 207 – front bulb replacement................. 168
Power steering .................................... 96 – control ............................................ 61 – rear bulb replacement .................. 170
Power windows .................................. 79 – nozzles ............................................ 208 Smart washing ..................................... 60
Presetting for mounting the Rearview mirrors Smoker’s kit ......................................... 72
INDEX
“Isofix Universal” child – door mirrors ................................. 47 Snow chains ......................................... 131
restraint system................................. 120 – driving mirror ................................ 48 Sound system ...................................... 99
224
222-232 LINEA 1ed GB 9-09-2008 14:25 Pagina 225
AND CONTROLS
DASHBOARD
– type ................................................. 205 – tow hook installation ................... 129 wiper blades ...................................... 194
Speedometer ....................................... 16 Transmission ........................................ 207 Windscreen washer
Starting and driving ............................ 121 – control ............................................ 68
Trip computer ..................................... 42
– fluid level ........................................ 187
DEVICES
Starting the engine
SAFETY
Tyres
Windscreen wiper
– bump starting ................................ 147 – replacing a wheel ........................... 147
– blades .............................................. 194
– diesel engines ................................ 123 – maintenance .................................. 193
MESSAGES
– stopping the engine ....................... 124 Using the manual gearbox .............. 126
– warm up the engine after
just started.......................................... 124 Ventilation .......................................... 49
EMERGENCY
Steering .................................................. 208 Warning lights and messages .........
IN AN
133
Steering column lock ......................... 13 Weights ................................................ 215
Steering wheel ..................................... 47
Wheel..................................................... 206
SPECIFICATIONS MAINTENANCE
Sunroof .................................................. 74
VEHICLE
– replacing a wheel .................. 147-155
Sun visors ............................................. 81
– spare wheel ................................... 211
Suspensions .......................................... 208
– wheel geometry ............................ 209
Symbols ................................................. 6
TECHNICAL
Wheel rims
Tailgate ................................................ 86 – understanding rim marking ........ 210
Technical specifications ..................... 201 Window washing ................................. 68
Third brake light ................................. 164 Window winders ................................. 83
INDEX
Top speeds ........................................... 214 Windscreen/rear window/
Towing the car .................................... 175 headlight washer fluid level ............ 200
225
222-232 LINEA 1ed GB 9-09-2008 14:25 Pagina 226
NOTES
222-232 LINEA 1ed GB 9-09-2008 14:25 Pagina 228
222-232 LINEA 1ed GB 9-09-2008 14:25 Pagina 229
222-232 LINEA 1ed GB 9-09-2008 14:25 Pagina 230
222-232 LINEA 1ed GB 9-09-2008 14:25 Pagina 231
222-232 LINEA 1ed GB 9-09-2008 14:25 Pagina 232
Add +0.3 bar to the prescribed inflation pressure when the tyres are warm. Recheck pressure value with cold tyres.
With snow tyres, add +0.2 bar to the inflation pressure value prescribed for standard tyres.
Refuel petrol engines with unleaded petrol with octane rating (RON) no lower than 95 only (EN 228 Specifications)
Refuel diesel engines with diesel fuel for motor vehicles only (EN 590 Specifications)
Fiat Group Automobiles S.p.A. - Customer Services - Technical Services - Service Engineering - Largo Senatore G. Agnelli, 5 - 10040 Volvera - Torino (Italia)
Print N. 603.81.411 - 09/2008 - 2nd Edition