Saep 1131 PDF
Saep 1131 PDF
Saep 1131 PDF
1 Scope............................................................. 2
2 Authorization.................................................. 2
3 Detailed Instructions for Relief Valve
Authorization through SAP Workflow............. 3
4 Applicable Documents................................. 10
5 Sub-Committee Members............................ 11
1 Scope
1.1 This Procedure contains instructions for Saudi Aramco Relief Device
Authorization through SAP Workflow. It contains Authorization requirements
and detailed instructions for completing each data field.
1.2 The referenced tables are standard values attached for guidance. Each user can
display these tables using the SAP Transaction ZI0006 “PM Z Table
Maintenance” as required.
1.3 The applicable Z-Table identification code within SAP PM Transaction ZI0006
is shown as Table Name, i.e., ZIPMMANUF and ZISERVICECODE for PM
Manufacturer's name and Service codes, respectively, etc.
2 Authorization
2.1.2 The Originating Engineer enters the data into the corporate SAP
system using the Transaction code IE01 (Create Equipment). At this
stage of the process, the RV is assigned a permanent number which
should be kept in a permanent RV data records having “CRTD”
Created mode in User Status. Once all required RV data records are
entered, then the Originator should select “Awaiting Approval” mode
in User Status field of the SAP system.
Commentary Note:
Page 2 of 16
Document Responsibility: Inspection Engineering Standards Committee SAEP-1131
Issue Date: 16 September 2015
Next Planned Update: 16 September 2018 Pressure Relief Device Authorization through SAP Workflow
Page 3 of 16
Document Responsibility: Inspection Engineering Standards Committee SAEP-1131
Issue Date: 16 September 2015
Next Planned Update: 16 September 2018 Pressure Relief Device Authorization through SAP Workflow
Commentary Note:
The Maintenance Plant No. in the SAP System refers to the physical
location custodian of the RV
3.1.6.1 ROW 1
RV Type: Select the RV type specified by Form 8020-6xx-
ENG. from the drop down menu
BODY MATERIAL field: Select the body material type
specified by Form 8020-6xx-ENG. from the drop down menu
Page 4 of 16
Document Responsibility: Inspection Engineering Standards Committee SAEP-1131
Issue Date: 16 September 2015
Next Planned Update: 16 September 2018 Pressure Relief Device Authorization through SAP Workflow
Commentary Note:
3.1.6.2 ROW 2
SPRING/PIN MATERIAL field: Select the spring or pin
material specified by Form 8020-6xx-ENG. from the drop
down menu
BELLOW MATERIAL field: Select the bellow material
specified by Saudi Aramco Form 8020-6xx-ENG. from the
drop down menu
3.1.6.3 ROW 3
INLET SIZE field: Enter the inlet size in inches, from Saudi
Aramco Form 8020-6xx-ENG. Use the attached Inlet/Outlet
Size standardized Material Abbreviation Entry Code Table I.
In the Other tab, the pull down menu of the field will display
the applicable table and enable you to make the appropriate
selection.
INLET RATING field: Enter the inlet rating from Saudi
Aramco Form 8020-6xx-ENG, i.e., 150, 300, 3000, 6000,
1500. Use the attached Flanged/Threaded end RV
Rating/Connection type standardized Material Abbreviation
Entry Code Table IIa or Z-Table ZIINLETRATING. Using
Z-Table (SAP), the field will display the applicable table and
enable you to make the appropriate selection.
INLET CONNECTION TYPE field: Enter the inlet
connection type from Saudi Aramco Form 8020-6xx-ENG,
i.e.; RF, RJ, FF, NPTM, or NPTF. Use the attached
Flanged/Threaded end RV Rating/Connection type
standardized Material Abbreviation Entry Code Table IIb or
Z-Table ZIINLETCONNE. Using Z-Table (SAP), the field
will display the applicable table and enable you to make the
appropriate selection.
Page 5 of 16
Document Responsibility: Inspection Engineering Standards Committee SAEP-1131
Issue Date: 16 September 2015
Next Planned Update: 16 September 2018 Pressure Relief Device Authorization through SAP Workflow
3.1.6.4 ROW 4
OUTLET SIZE field: Enter the outlet size in inches, from
Form 8020-6xx-ENG. Use the attached Inlet/Outlet Size
standardized Material Abbreviation Entry Code Table I. In the
Other tab, the pull down menu of the field will display the
applicable table and enable you to make the appropriate
selection.
OUTLET RATING field: Enter the outlet rating from Saudi
Aramco Form 8020-6xx-ENG, i.e., 150, 300, 3000, 6000,
1500. Use the attached Flanged/Threaded end RV
Rating/Connection type standardized Material Abbreviation
Entry Code Table IIa or Z-Table ZIINLETRATING. Using
Z-Table (SAP), the field will display the applicable table and
enable you to make the appropriate selection.
OUTLET CONNECTION TYPE field: Enter the outlet
connection type from Form 8020-6xx-ENG, i.e.; RF, RJ, FF,
NPTM, or NPTF. Use the attached Flanged/Threaded end RV
Rating/Connection type standardized Material Abbreviation
Entry Code Table IIa or Z-Table ZIINLETCONNE. Using
Z-Table (SAP), the field will display the applicable table and
enable you to make the appropriate selection.
ORIFICE SIZE field: Enter the orifice size as specified by
Saudi Aramco Form 8020-6xx-ENG. Ensure that the entry
contains three significant digits as in the commentary above
under Orifice Type.
Page 6 of 16
Document Responsibility: Inspection Engineering Standards Committee SAEP-1131
Issue Date: 16 September 2015
Next Planned Update: 16 September 2018 Pressure Relief Device Authorization through SAP Workflow
3.1.6.5 ROW 5
SPRING LOW field: Enter the low value for the actual spring
installed as specified by Saudi Aramco Form 8020-6xx-ENG
SPRING HIGH field: Enter the high value for the actual spring
installed as specified by Saudi Aramco Form 8020-6xx-ENG
Commentary Note:
3.1.6.6 ROW 6
CDTP field: Enter CDTP, Cold Differential Test Pressure
(i.e., the pressure at which the RV is adjusted to open on the
test stand) from Saudi Aramco Form 8020-6xx-EN.
CDTP is required for all spring operated RVs with
superimposed (constant) back pressure (unless they contain a
bellows), and for some manufacturer's valves depending on the
operating temperature. Contact P&CSD, Dhahran for
calculation methods.
SET PRESSURE field: Enter set pressure from Saudi Aramco
Form 8020-6xx-ENG.
PRESSURE UNIT: field: Enter pressure units (PSIG, kPa, or
INWG, etc.) from Saudi Aramco Form 8020-6xx-ENG. Use
the attached standardized Pressure Unit Entry Code Table IV.
In the Other tab, the pull down menu of the field will display
the applicable table and enable you to make the appropriate
selection.
3.1.6.7 ROW 7
VACUUM PRESSURE field:: Enter Vacuum Pressure from
Saudi Aramco Form 8020-613-ENG.
Page 7 of 16
Document Responsibility: Inspection Engineering Standards Committee SAEP-1131
Issue Date: 16 September 2015
Next Planned Update: 16 September 2018 Pressure Relief Device Authorization through SAP Workflow
3.1.6.8 ROW 8
PALLET WEIGHT field: Enter the pallet weight for pallet type
RVs.
PALLET WEIGHT UNIT field: Enter the pallet weight unit
(LB, oz, gm, kg). Use the attached standardized Pressure Unit
Entry Code Table IV. In the Other tab, the pull down menu of
the field will display the applicable table and enable you to
make the appropriate selection.
Commentary Note:
If the RV has two pallet weights (one for pressure and one for
vacuum), then the value for the pressure pallet shall be filled in
the pallet weight field and the vacuum pallet weight shall be
filled in the vacuum pressure field.
Page 8 of 16
Document Responsibility: Inspection Engineering Standards Committee SAEP-1131
Issue Date: 16 September 2015
Next Planned Update: 16 September 2018 Pressure Relief Device Authorization through SAP Workflow
3.1.6.9 ROW 9
MANUFACTURER field: Enter the name of manufacturer
from Saudi Aramco Form 8020-6xx-ENG. Use the
standardized Manufacturer Entry Code Table ZIPMMANUF.
In this Z-table, the field will display the applicable table and
enable you to make the appropriate selection. If the RV's
manufacturer does not exist in the table, call the RV
Administrator for assistance. The request for a new
manufacturer must be supported by a specification sheet or
manufacturer's catalog, etc. in order to validate the request.
RV MODEL NUMBER field: Enter the RV Manufacturer's
Model number from Form 8020-6xx-ENG.
OUTER SEAT DIAMETER field: This field is only required
to be filled in if a Hydraulic Assisted Test (i.e., Trevitesting) is
to be used on the valve. If used, enter the measured outer
diameter of the valve seat, in inches. Valve must be
disassembled and measured to ± 25.4 um (0.001 inch). Do not
include unit description.
INNER SEAT DIAMETER field: This field is only required to
be filled in if a Hydraulic Assisted Test (i.e., Trevitesting) is to
be used on the valve. If used, enter the measured inner
diameter of the valve seat, in inches. Valve must be
disassembled and measured to ± 25.4 um (0.001 inch). Do not
include unit description.
3.1.6.10 ROW 10
PZV TAG NO. field: Enter the Saudi Aramco Instrument Tag
Number (PZV) from Saudi Aramco Form 8020-6xx-ENG. Do
not include “PZV” within the tag number.
ISS DRAWING NO. field: Enter the Saudi Aramco drawing
number of Saudi Aramco Form 8020-6xx-ENG or the
applicable ISS drawing number based on the RV type, located
at bottom right corner. This is the “DE-xxxx” drawing no.
SERVICE field: Note the service fluid from Saudi Aramco
Form 8020-6xx-ENG. Use the standardized Service Entry
Code ZIRVSERVICE in SAP system. Using Z-Table, the field
Page 9 of 16
Document Responsibility: Inspection Engineering Standards Committee SAEP-1131
Issue Date: 16 September 2015
Next Planned Update: 16 September 2018 Pressure Relief Device Authorization through SAP Workflow
will display the applicable table and enable you to make the
appropriate selection. If the appropriate service code does not
exist in the table, call the RV Administrator for assistance.
Service field shall be the actual service handled by the RV.
SERVICE CODE field: Enter code 'A' for Air, 'L' for Liquid,
'G' for gas/vapor or 'S' for steam. Service code shall be the
actual service handled by the RV.
DESIGN CODE field: Enter the design code from Saudi
Aramco Form 8020-6xx-ENG.
Enter “1” for ASME SEC I RV's.
Enter “8” for ASME SEC VIII D1 RV's and Buckling
(Rupture) Pins.
Enter “P” for API type RVs.
Enter “R” for Rupture Discs & Surge Relief Valve
4 Applicable Documents
The requirements contained in the following documents apply to the extent specified in
this procedure.
Page 10 of 16
Document Responsibility: Inspection Engineering Standards Committee SAEP-1131
Issue Date: 16 September 2015
Next Planned Update: 16 September 2018 Pressure Relief Device Authorization through SAP Workflow
Revision Summary
16 September 2015 Revised the Next Planned Update, reaffirmed the content of the document, and reissued
as major revision.
Page 11 of 16
Document Responsibility: Inspection Engineering Standards Committee SAEP-1131
Issue Date: 16 September 2015
Next Planned Update: 16 September 2018 Pressure Relief Device Authorization through SAP Workflow
0.25 30.0
0.50 32.0
0.75 34.0
1.0 36.0
1.5 38.0
2.0 40.0
3.0 42.0
4.0 44.0
6.0 46.00
8.0 48.00
10.0
12.0
14.0
16.0
18.0
20.0
22.0
24.0
125
150 1500
300 2000
400 2500
600 3000
800 5000
900 6000
9000
10000
Page 12 of 16
Document Responsibility: Inspection Engineering Standards Committee SAEP-1131
Issue Date: 16 September 2015
Next Planned Update: 16 September 2018 Pressure Relief Device Authorization through SAP Workflow
Raised Face RF
Flat Face FF
Ring Joint RJ
Nominal Pipe Thread-Male NPTM
Nominal Pipe Thread-Female NPTF
0.110 D
0.196 E
0.307 F
0.503 G
0.785 H
1.287 J
1.838 K
2.853 L
3.60 M
4.34 N
6.38 P
11.05 Q
16.00 R
26.00 T
The above table is to be used as a cross reference for Orifice Sizes and Orifice Type.
Page 13 of 16
Document Responsibility: Inspection Engineering Standards Committee SAEP-1131
Issue Date: 16 September 2015
Next Planned Update: 16 September 2018 Pressure Relief Device Authorization through SAP Workflow
Pounds Lb
Kilograms Kg
Grams gm
Ounces oz
Page 14 of 16
Document Responsibility: Inspection Engineering Standards Committee SAEP-1131
Issue Date: 16 September 2015
Next Planned Update: 16 September 2018 Pressure Relief Device Authorization through SAP Workflow
Fahrenheit F
Centigrade C
Kelvin K
Rankine R
Liquid L
Gas/Vapor G
Steam S
Air A
Page 15 of 16
Document Responsibility: Inspection Engineering Standards Committee SAEP-1131
Issue Date: 16 September 2015
Next Planned Update: 16 September 2018 Pressure Relief Device Authorization through SAP Workflow
ASME SEC I 1
ASME SEC VIII D1 & RP* 8
API Type Valves P
Rupture Discs & Surge Relief Valves R
Page 16 of 16