Nothing Special   »   [go: up one dir, main page]
Scribd Logo
Upload

Welcome to Scribd!

  • 117 views

    20 PHD Fig. 054-907

    Uploaded by

    juan yenque
    This document provides information about a sway brace fitting made by PHD Manufacturing. The fitting is designed to brace pipe against sway and seismic disturbances as part of a 4-way sway brace assembly using 1" or 1-1/4" Schedule 40 steel pipe. It can connect two brace pipes at angles and must be installed within 3" of the braced pipe according to NFPA 13 standards using the manufacturer's instructions.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    20 PHD Fig. 054-907

    Uploaded by

    juan yenque
    117 views1 page
    This document provides information about a sway brace fitting made by PHD Manufacturing. The fitting is designed to brace pipe against sway and seismic disturbances as part of a 4-way sway brace assembly using 1" or 1-1/4" Schedule 40 steel pipe. It can connect two brace pipes at angles and must be installed within 3" of the braced pipe according to NFPA 13 standards using the manufacturer's instructions.

    Original Description:

    Soportess

    Original Title

    3. 20 PHD FIG. 054-907

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    This document provides information about a sway brace fitting made by PHD Manufacturing. The fitting is designed to brace pipe against sway and seismic disturbances as part of a 4-way sway brace assembly using 1" or 1-1/4" Schedule 40 steel pipe. It can connect two brace pipes at angles and must be installed within 3" of the braced pipe according to NFPA 13 standards using the manufacturer's instructions.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    117 views1 page

    20 PHD Fig. 054-907

    Uploaded by

    juan yenque
    This document provides information about a sway brace fitting made by PHD Manufacturing. The fitting is designed to brace pipe against sway and seismic disturbances as part of a 4-way sway brace assembly using 1" or 1-1/4" Schedule 40 steel pipe. It can connect two brace pipes at angles and must be installed within 3" of the braced pipe according to NFPA 13 standards using the manufacturer's instructions.

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    You are on page 1of 1

    S WAY B RACE F ITTINGS

    FUNCTION:

    Designed for bracing pipe against sway and seismic disturbances.


    Intended to function as a 4-way sway brace assembly component
    for use on risers and other vertical piping configurations, each
    brace pipe must be used in conjunction with a PHD
    Manufacturing pipe attachment. Fig. 054 can also function as a
    longitudinal brace connection when attached to a lateral brace
    assembly using PHD Manufacturing sway brace fittings where
    building codes permit. The brace attachment component of a
    sway brace system used in conjunction with PHD Manufacturing
    structural attachment fittings and joining together two bracing
    pipe elements forming a complete sway brace assembly. Sway
    brace assemblies are intended to be installed in accordance with
    NFPA 13 and the manufacturers installation instructions.

    SIZE:

    Pipe size 1" thru 4" Schedule 10 thru 40 IP. Pipe size used for
    bracing 1" and 1-1/4" Schedule 40 IP.

    FINISH:

    Electro-galvanized

    MATERIAL:

    Low Carbon Steel

    INSTALL:

    Insert bracing pipe into fitting against the pivot bolt and tighten
    each fitting set screw finger tight. Then tighten each set screw
    evenly until hex head breaks off. Fitting can pivot for adjustment
    to proper brace angle, then tighten pivot bolt. Bracing connection
    must be positioned as close as possible to the braced pipe and
    cannot be more than 3" away.

    APPROVALS: Underwriters Laboratories listed for US and Canada


    Listed for use with NFPA and PHD sway brace components only

    Fig. 054 Combinations


    Brace Pipe Max. Rec.
    Combinations
    Load
    1
    1
    1-1/4

    1
    1-1/4
    1-1/4

    655
    655
    655

    PHD Manufacturing, Inc.

    Fig. 054
    THREADLESS SWAY
    BRACE FITTING

    You might also like