Sony HCD Bx3 Dx3

HCD-BX3/DX3
SERVICE MANUAL US Model

Canadian Model
Ver 1.1 2001.11 AEP Model
UK Model
HCD-BX3
E Model
Australian Model
HCD-DX3
• HCD-BX3/DX3 are the tuner, deck,

CD and amplifier section in MHC-
BX3/DX3. Photo: HCD-BX3
Model Name Using Similar Mechanism NEW

CD CD Mechanism Type CDM58-K2BD38
Section Base Unit Name BU-K2BD38
Optical Pick-up Name KSM-213DAP
Tape deck Model Name Using Similar Mechanism NEW
Section Tape Transport Mechanism Type TCM-230MWR11
SPECIFICATIONS
AUDIO POWER SPECIFICATIONS: DIN power output (rated) 75 + 75 watts
(HCD-BX3 US model only) (6 ohms at 1 kHz, DIN)
POWER OUTPUT AND TOTAL Continuous RMS power output (reference)
HARMONIC DISTORTION: 100 + 100 watts
with 6 ohm loads both channels driven, from 120-10,000 Hz; rates (6 ohms at 1 kHz, 10% THD)
75 watts per channel minimum RMS power, with no more than 10% Inputs
total harmonic distortion from 250 milliwatts to rated output. MD/VIDEO IN: voltage 450/250 mV,
(phono jacks) impedance 47 kilohms
Amplifier section MIC: sensitivity 1 mV,
US, Canadian model: (mini jack) impedance 10 kilohms
HCD-BX3:
Continuous RMS power output (reference) Outputs
60 + 60 watts PHONES: accepts headphones of
(6 ohms at 1 kHz, 10% THD) (stereo mini jack) 8 ohms or more
Total harmonic distortion less than 0.07% SPEAKER: accepts impedance of 6 to 16 ohms
(6 ohms at 1 kHz, 35 W)
CD player section
AEP, UK model: System Compact disc and digital audio system
HCD-BX3: Laser Semiconductor laser (λ=780 nm)
DIN power output (rated) 45 + 45 watts Emission duration: continuous
(6 ohms at 1 kHz, DIN) Laser output Max. 44.6 µW*
Continuous RMS power output (reference) *This output is the value measured at a
60 + 60 watts distance of 200 mm from the objective
(6 ohms at 1 kHz, 10% THD) lens surface on the Optical Pick-up Block
Music power output (reference) with 7 mm aperture.
150 + 150 watts
(6 ohms at 1 kHz, 10% THD) — Continued on next page —
Other model:
HCD-DX3:
The following measured at AC 120, 220, 240 V 50/60 Hz COMPACT DISC DECK RECEIVER
9-929-055-12 Sony Corporation
2001K1600-1 Home Audio Company
© 2001.11 Published by Sony Engineering Corporation
Wavelength 780 – 790 nm Mass
Frequency response 2 Hz – 20 kHz (±0.5 dB) US model:
Signal-to-noise ratio More than 90 dB HCD-BX3: Approx. 7.8 kg
Dynamic range More than 90 dB Canadian model:
CD OPTICAL DIGITAL OUT HCD-BX3: Approx. 7.8 kg
(Square optical connector jack, rear panel) AEP model:
Wavelength 660 nm HCD-BX3: Approx. 7.9 kg
Output Level –18 dBm Other models:
HCD-DX3: Approx. 8.9 kg
Tape player section
Recording system 4-track 2-channel stereo Design and specifications are subject to change without notice.
Frequency response 40 – 13,000 Hz (±3 dB), using Sony TYPE I
cassette
Tuner section
FM stereo, FM/AM superheterodyne tuner SAFETY CHECK-OUT
(US model only)
FM tuner section
Tuning range 87.5 – 108.0 MHz After correcting the original service problem, perform the
Antenna FM lead antenna following safety checks before releasing the set to the customer:
Antenna terminals 75 ohm unbalanced Check the antenna terminals, metal trim, “metallized” knobs, screws,
Intermediate frequency 10.7 MHz and all other exposed metal parts for AC leakage. Check leakage as
described below.
AM tuner section
Tuning range
US, Canadian, Mexican, Argentina models: LEAKAGE
530 – 1,710 kHz
(with the interval set at 10 kHz) The AC leakage from any exposed metal part to earth ground and
531 – 1,710 kHz from all exposed metal parts to any exposed metal part having a
(with the interval set at 9 kHz) return to chassis, must not exceed 0.5 mA (500 microampers).
AEP, Saudi Arabia models:
Leakage current can be measured by any one of three methods.
531 – 1,602 kHz
(with the interval set at 9 kHz)
Other models: 531 – 1,602 kHz 1. A commercial leakage tester, such as the Simpson 229 or RCA
(with the interval set at 9 kHz) WT-540A. Follow the manufacturers’ instructions to use these
530 – 1,710 kHz instruments.
(with the interval set at 10 kHz)
Antenna AM loop antenna 2. A battery-operated AC milliammeter. The Data Precision 245
Antenna terminals External antenna terminal digital multimeter is suitable for this job.
Intermediate frequency 450 kHz
General 3. Measuring the voltage drop across a resistor by means of a

Power requirements VOM or battery-operated AC voltmeter. The “limit” indication
US, Canadian models: 120 V AC, 60 Hz is 0.75 V, so analog meters must have an accurate low-voltage
AEP model: 230 V AC, 50/60 Hz scale. The Simpson 250 and Sanwa SH-63Trd are examples of
Australian model: 230-240 V AC, 50/60 Hz a passive VOM that is suitable. Nearly all battery operated
Mexican model: 120 V AC, 50/60 Hz digital multimeters that have a 2V AC range are suitable. (See
Other models: 120 V, 220 V or 230 - 240 V AC, 50/60 Hz Fig. A)
Adjustable with voltage selector
Power consumption To Exposed Metal

US model:
Parts on Set
HCD-BX3: 140 watts
Canadian model:
HCD-BX3: 130 watts
AEP model:
HCD-BX3: 130 watts AC
voltmeter
Other models: 0.15µF 1.5kΩ (0.75V)
HCD-DX3: 170 watts
Dimensions (w/h/d)
HCD-BX3/DX3: Approx. 280 x 325 x 403 mm
Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.
SAFETY-RELATED COMPONENT WARNING!! ATTENTION AU COMPOSANT AYANT RAPPORT

À LA SÉCURITÉ!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
PUBLISHED BY SONY. DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
2
NOTES ON HANDLING THE OPTICAL PICK-UP TABLE OF CONTENTS
BLOCK OR BASE UNIT 1. SERVICE NOTE ······························································· 4
The laser diode in the optical pick-up block may suffer electrostatic 2. GENERAL ·········································································· 5
break-down because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body. 3. DISASSEMBY ·································································· 7
During repair, pay attention to electrostatic break-down and also
4. TEST MODE ···································································· 12
use the procedure in the printed matter which is included in the
repair parts. 5. MECHANICAL ADJUSTMENTS ····························· 16
The flexible board is easily damaged and should be handled with
care. 6. ELECTRICAL ADJUSTMENTS ······························· 16
NOTES ON LASER DIODE EMISSION CHECK 7. DIAGRAMS

7-1. Circuit Board Location ················································· 21
7-2. Block Diagrams ···························································· 22
The laser beam on this model is concentrated so as to be focused on 7-3. Printed Wiring Board BD Section ···························· 24
the disc reflective surface by the objective lens in the optical pick- 7-4. Schematic Diagram BD Section ······························· 25
up block. Therefore, when checking the laser diode emission, 7-5. Printed Wiring Board Main Section ························· 26
observe from more than 30 cm away from the objective lens. 7-6. Schematic Diagram Main Section (1/3) ··················· 27
7-7. Schematic Diagram Main Section (2/3) ··················· 28
7-8. Schematic Diagram Main Section (3/3) ··················· 29
Laser component in this product is capable 7-9. Printed Wiring Board AMP Section ························· 30
of emitting radiation exceeding the limit for 7-10. Schematic Diagram AMP Section ·························· 31
Class 1. 7-11. Printed Wiring Board Panel Section ······················· 32
7-12. Schematic Diagram Panel Section ·························· 33
7-13. Printed Wiring Board Leaf SW Section ·················· 34
7-14. Schematic Diagram Leaf SW Section ···················· 35
7-15. Printed Wiring Board Driver Section ······················ 36
7-16. Schematic Diagram Driver Section ························ 37
7-17. Printed Wiring Board Trans Section ······················· 38
7-18. Schematic Diagram Trans Section ·························· 39
7-19. IC Pin Function Description ······································· 40
7-20. IC Block Diagrams ····················································· 42
This appliance is classified as a CLASS 1 LASER product. The
CLASS 1 LASER PRODUCT MARKING is located on the rear 8. EXPLODED VIEWS
exterior. 8-1. Main Section ································································· 45
8-2. Panel Section ································································ 46
8-3. Main Board Section ······················································ 47
CAUTION 8-4. Tape Mechanism Section ·············································· 48
Use of controls or adjustments or performance of procedures 8-5. CD Mechanism Section ················································ 49
other than those specified herein may result in hazardous radiation
exposure. 9. ELECTRICAL PARTS LIST ······································· 50
MODEL IDENTIFICATION
Notes on chip component replacement — BACK PANEL — PARTS No.
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
Flexible Circuit Board Repairing

• Keep the temperature of soldering iron around 270˚C
during repairing.
• Do not touch the soldering iron on the same conductor of the
circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering
or unsoldering.
MODEL PARTS No.

BX3: AEP, UK, G, AED models 4-224-547-0s
DX3: AR, E, EA, SP, TW, MY models 4-224-547-1s
BX3: US, CND models 4-224-547-2s
DX3: AUS, KR, MX, TH models 4-224-547-4s
BX3: CIS model 4-226-245-0s
• Abbreviation
CND : Canadian model SP : Singapore model
AUS : Australian model TH : Thai model
G : German model TW : Taiwan model
AED : North European model KR : Korea model
EA : Saudi Arabia model MX : Mexican model
MY : Malaysia model AR : Argentina model
3
SECTION 1
SERVICE NOTE
Note for installing the panel board
2 Panel board
Screw hole Hot melt
Attach the panel board with

fourteen screws (+BVTP 2.6 × 8 )
1 Cut the fourteen melted-connection points with a cutting plier.
after the board is removed once.
Do not tighten the screws excessively.
4
SECTION 2
GENERAL
1 2 3 4 5
wa 6
w; 7 wd wf
ql 8
ws wg
qk 9
wh
qj wj
q;
qh qg qf qd qs qa es ea e; wl wk
Photo: HCD-BX3
1 – . button ws MD/VIDEO button and indicator

2 x button wd TAPE A/B button and indicator
3 gG button wf CD button and indicator
4 S button wg TUNER/BAND button and indicator
5 > + button wh CROOVE button and indicator
6 PLAY MODE button wj SURROUND button and indicator
7 REPLAY button wk CD SYNC HI-DUB button
8 EDIT button wl REC PAUSE/START button and indicator
9 VOLUME knob e; KARAOKE PON button
q; PHONE jack ea ENTER button
qa OPEN/CLOSE button es EQ EDIT button
qs DISC 3 button
qd DISC 2 button
qf DISC 1 button
qg DISC SKIP EX-CHANGE button
qh CURSOL button
qj MIC jack
qk MIC LEVEL knob
ql SPECTRUM button
w; DISPLAY button
wa @/1 button
5
6
Step 1: Hooking up the system
2 Press . or > repeatedly to set (continued) Step 2: Setting the
the hour.
Step 3: Presetting
radio stations To attach the front speaker pads time
3 Press ENTER. Attach the supplied front speaker pads to the
bottom of the speakers to stabilize the
The minute indication flashes.
You can preset a total of 30 preset stations (20 speakers and prevent them from slipping. You must set the time before using the timer
for FM and 10 for AM). functions.
instruction manual.
The clock uses a 24-hour system on the

?/1 European model, and a 12-hour system on
(Power) 2 3 other models.
The 24-hour system is used for illustration
purposes.
This section is extracted from
4 Press . or > repeatedly to set

1
the minute.
hH S s
l L
5 Press ENTER. Inserting two size AA (R6) 2,4 3,5
The clock starts working. j J
batteries into the remote
H S s
Tip
If you make a mistake, start over from step 1.
To change the time
The previous explanation shows how to set
e
the time while the power is off. To change the
E
time while the power is on, do the following: Shuttle E
41 e
1 Press CLOCK/TIMER SET.
2 Press . or > repeatedly to select SET
CLOCK.
Tip
3 Press ENTER.
With normal use, the batteries should last for about
4 Perform steps 2 through 5 above. six months. When the remote no longer operates 1 Press CLOCK/TIMER SET.
Note the system, replace both batteries with new ones. The hour indication flashes.
The clock settings are canceled when you disconnect Note
continued
the power cord or if a power failure occurs. If you do not use the remote for a long period of
time, remove the batteries to prevent possible
damage from battery leakage.
When carrying this system

Make sure that all discs are removed from the
unit. To protect the CD mechanism, hold
down CD and press ?/1 while the power is
on. “LOCK” appears in the display and the
power is turned off.
7 6
SECTION 3
DISASSEMBY
Note : Follow the disassembly procedure in the numerical order given.
3-1. UPPER CASE (TOP)

Upper case (Top) 9 Two screws (+BVTP 3 × 10)
5 Two screws (Case) q;
7 Two screws
(+BVTP 3 × 10)
4
Case (L)
6 Screw (Case)
Case (R)
3 Two screws
1 Two screws (Case)
2 Screw (Case)
3-2. LOADING PANEL ASSY

Loading panel assy
CD mechanism deck (CDM58)

1 Turn the pulley to the direction of arrow.
Front panel side
pulley 3
2 Pull-out the disc tray.
7
3-3. FRONT PANEL SECTION
CD mechanism deck (CDM58)
4 Screw (+BVTP 3 × 10)
2 Connector (CN302) 1 Flat type wire (CN304)
3 Connector (CN303)
5 Screw (+BVTP 3 × 10)
Front panel section
6 Three screws (+BVTT 3 × 6)
3-4. TAPE MECHANISM DECK

4 Bracket (Heart cam L)
3 Screw (+BVTP 2.6 × 8)
5 Five screws (+BVTP 2.6 × 8)

1 Screw (+BVTP 2.6 × 8)
2 Bracket (Heart cam R)
6 Tape mechanism deck
8
3-5. PANEL BOARD
7 Six claws
5
4 Ring (Vol)
8 Panel board
3 Bracket (Volume)
2 Hexagon nut
1 Knob (Volume) 6 Cut the fourteen melted-connection points with a cutting plier.
Note: When attching the panel board,

refer to "Service Note" on page 4.
3-6. SUB-TRANS BOARD AND TRANS BOARD

2 Connector (CN974)
7 Panel, back
1 Connector (CN975)
6 Five screws
(+BVTP 3 × 10)
8 Two screws
qa Trans board
(+BVTT 4 × 6)
9 Two screws (+BVTT 4 × 6)
q; Trans 4 Sub-trans
board
3 Two screws
(+BVTP 3 × 10)
5 Five screws
(+BVTP 3 × 10)
9
3-7. MAIN BOARD AND AMP BOARD
4 Three screws (+BVTP 3 × 10) 7 Heat sink
6 Two screws (+BVTP 3 × 10)
5 AMP board
2 Main board
3-8. LEAF SW BOARD, HEAD (A) BOARD AND HEAD (B) BOARD
2 Remove the two solderings.
5 Leaf SW board
4 Five claws
1 Remove the two solderings.
3 Remove the four solderings.
7 Head (A) board
9 Head (B) board

6 Screw (+PS 2.6 × 5)
8 Screw (+PS 2.6 × 5)
10
3-9. BASE UNIT
3
4 Two insulators
Base unit
1 Flat type wire (CN101)
5 Two insulators
2 Four screws (+PTPWH 2.6)
3-10. DRIVER BOARD, MOTOR BOARD AND ADDRESS SENSOR BOARD
q; Screw (+PTPWH 2.6 × 8)
5 Three screws (+BVTP 2.6 × 8)

7 Motor board
4 Flat type wire (CN721)
qa Tray
qs Screw (+BVTP 2.6 × 8) 6 Remove the two solderings of motor.
qd Address sensor board 8 Connector (CN722)
2 Driver board
3 Connector (CN701)
1 Screw (+BVTP 2.6 × 8)
9 Pull-out the disc tray.
11
SECTION 4
TEST MODE
[MC Cold Reset] [Change-over of MW Tuner Step between 9 kHz and
• The cold reset clears all data including preset data stored in the 10 kHz]
RAM to initial conditions. Execute this mode when returning • A step of MW channels can be changed over between 9 kHz
the set to the customer. and 10 kHz.
Procedure: Procedure:
1. Press three buttons x , ENTER , and ?/1 simulta-neously. 1. Press ?/1 button to turn the set ON.
2. The fluorescent indicator tube displays “COLD RESET” and 2. Select the function “TUNER”, and press TUNER/BAND
the set is reset. button to select the BAND “MW”.
3. Press ?/1 button to turn the set OFF.
[CD Ship Mode] 4. Press ENTER and ?/1 buttons simultaneously, and the display
• This mode moves the pickup to the position durable to vibra- of fluorescent indicator tube changes to “MW 9 k STEP” or
tion. Use this mode when returning the set to the customer after “MW 10 k STEP”, and thus the channel step is changed over.
repair.
Procedure: [GC Test Mode]
1. Press 1/u button to turn the set ON. • This mode is used to check the software version, FL tube, LED,
2. Press CD button and 1/u button simultaneously. keyboard and VACS.
3. After the "STANDBY" display blinks six times, a message Procedure:
“LOCK” is displayed on the fluorescent indicator tube, and the 1. Press three buttons x , ENTER , and DISC 2 simultaneously.
CD ship mode is set. 2. LEDs and fluorescent indicator tube are all turned on.
3. When you want to enter the software version display mode,
[MC Hot Reset] press DISC 1 . The model number and destination are displayed.
• This mode resets the set with the preset data kept stored in the 4. Each time DISC 1 is pressed, the display changes starting
memory. The hot reset mode functions same as if the power from MC version, GC version, VC version, CD version, CM
cord is plugged in and out. version, ST version, TC version, TA version, TM version and
Procedure: BR version in this order, and returns to the model number and
1. Press three buttons x , ENTER , and DISC 1 simultaneously. destination display.
2. The fluorescent indicator tube becomes blank instantaneously, 5. When DISC 3 is pressed while the version numbers are being
and the set is reset. displayed except model number and destination, year, month
and day of the software creation appear. When DISC 3 is
[CD Service Mode] pressed again, the display returns to the software version display.
• This mode can run the CD sled motor freely. Use this mode, for When DISC 1 is pressed while year, month and day of the
instance, when cleaning the pickup. software creation are being displayed, the year, month and day
Procedure: of creation of the software versions are displayed in the same
1. Press ?/1 button to turn the set ON. order of version display.
2. Select the function “CD”. 6. Press DISC 2 button, and the key check mode is activated.
3. Press three buttons x , ENTER , and OPEN/CLOSE simul- 7. In the key check mode, the fluorescent indicator tube displays
taneously. “KEY0 VOL0”. Each time a button is pressed, “KEY” value
4. The CD service mode is selected. increases. However, once a button is pressed, it is no longer
5. With the CD in stop status, turn the shuttle knob clockwise to taken into account.
move the pickup to outside track, or turn the shuttle knob “VOL” value increases like 1, 2, 3 ... if rotating VOLUME
counter-clockwise to inside track. knob in “+” direction, or it decreases like 0, 9, 8 ... if rotating in
6. To exit from this mode, perform as follows: “–” direction.
1) Move the pickup to the most inside track. 8. Also when DISC 3 is pressed after lighting of all LEDs and FL
2) Press three buttons in the same manner as step 2. tubes, value of VACS appears.
Note: • Always move the pickup to most inside track when exiting from 9. To exit from this mode, press three buttons in the same manner
this mode. Otherwise, a disc will not be unloaded. as step 1, or disconnect the power cord.
• Do not run the sled motor excessively, otherwise the gear can be
chipped.
[VACS ON/OFF Mode]

• This mode is used to switch ON and OFF the VACS (Variable
Attenuation Control System).
Procedure:
Press the ENTER and SPECTRUM buttons simultaneously. The
message “VACS OFF” or “VACS ON” appears.
12
[MC Test Mode]
• This mode is used to check operations of the respective sections
of Amplifier, Tuner, CD and Tape.
Procedure:
1. Press the ?/1 button to turn on the set.
2. Press the three buttons of x , ENTER and DISC 3
simultaneously.
3. A message “TEST MODE” appears on the FL display tube.
4 When f (CURSOR UP) button is pressed, GEQ increases to
its maximum and a message “GEQ ALL MA” appears.
5. When F (CURSOR DOWN) button is pressed, GEQ decreases
to its minimum and a message “GEQ ALL M1” appears.
6. When g (CURSOR LEFT) or G (CURSOR RIGHT) button
is pressed, GEQ is set to flat and a message “GEQ FLAT”
appears.
7. When the VOLUME control knob is turned clockwise even
slightly, the sound volume increases to its maximum and a
message “VOLUME MAX” appears for two seconds, then the
display returns to the original display.
8. When the VOLUME control knob is turned counter-clockwise
even slightly, the sound volume decreases to its minimum and
a message “VOLUME MIN” appears for two seconds, then
the display returns to the original display.
9. In the test mode, the default-preset channel is called even when
the TUNER is selected and an attempt is made to call the preset
channel that has been stored in memory, by operating the Shuttle
knob. (It means that the memory is cleared.)
10. When CD is selected and the EDIT button is pressed, the disc
that is being chucked at this moment becomes the default
setting. It means that the default disc only is accessed when
any other discs are selected even though the display indication
changes accordingly. At the same time, the DISK SKIP EX-
CHANGE and OPEN/CLOSE cannot be accepted. (It means
that the tray motor and the turntable motor are disabled of their
operation.)
11. When a tape is inserted in Deck B and recording is started, the
input source function selects VIDEO automatically.
12. When x button is pressed to stop recording, the Tape (Deck)
B is selected and tape is rewound using the Shuttle knob, tape
is rewound, tape is stops at around the record-starting position
and playback of the recorded portion of the tape is started. If
PAUSE is inserted even once during recording, tape is rewound
to the position around the PAUSE position and is played back.
13. When the CD SYNC HI-DUB Button is press during playback
of Deck B, either normal speed or high speed can be selected
by this button.
14. Select the desired loop by pressing the PLAY MODE button.
Insert a test tape AMS-110A or AMS-RO to Deck A.
15. Press the SPECTRUM button to enter the AMS test mode.
16. After a tape is rewound first, the FF AMS is checked, and the
mechanism is shut off after detecting the AMS signal twice.
17. Then the REW AMS is checked and the mechanism is shut off
after detecting the AMS signal twice.
18. When the check is complete, a message of either OK or NG
appears.
19. When you want to exit this mode, press the ?/1 button twice.
The cold reset is enforced at the same time.
13
[Aging Mode]
This mode can be used for operation check of CD section and tape deck section.
• If an error occurred:
The aging operation stops and display status.
• If no error occurs:
The aging operation continues repeatedly.
1. Operating method of Aging Mode

Turn on the main power and select “CD” of the function.
1) Set a disc in DISC1 tray. Select ALL DISC CONTINUE, and REPEAT OFF.
2) Load the tapes recording use into the decks A and B respectively.
3) Press three buttons x , ENTER , and
DISC SKIP/EX-CHANGE simultaneously.
4) Aging operations of CD and tape are started at the same time.
5) To exit the aging mode, perform [MC Cold Reset].
3. Aging Mode in CD section

1) Display state
• No error occurs Display
AGING[*][*][*][*]
Note:
[*][*][*][*] : Number of aging operations
Error display
E ** s ## $$ %%
12 3 4 5
1 ** The error No. 00 indicates the newest error. As the error No. increases, it means the older error.
When you want to retrieve the error history, press the PLAY MODE button in the case of mechanism error.
Or press the REPEAT button in the case of NO DISC error.
2 s M: Mechanism error D: No disc error
3 ## Don’t care 01: FOCUS ERROR
02: GFS ERROR
03: SETUP ERROR
4 $$ High order digits only 01: NO DISC judgment without chucking retry
D: Stopped during closing due to problems other than mechanism. 02: NO DISC judgment after chucking retry
E: Stopped during opening due to problems other than mechanism.
C: Stopped during chucking due to problems other than mechanism.
F: Stopped during EX-opening due to problems other than mechanism.
5 %% Emergency related errors (High order digits only) Status at the time of NO DISC judgment
1: Stopped during chuck-up (High order digits only)
2: Stopped during chuck-down 1: STOP
3: Time out by EX-OPEN 2: SETUP
5: Time out by EX-CLOSE 3: TOC READ
4: ACCESS
5: PLAY BACK
6: PAUSE
7: MANUAL SEARCH (PLAY)
8: MANUAL SEARCH (PAUSE)
• When the buttons x , ENTER and DISC 1 are pressed simultaneously, number of time of the mechanism error and the NO DISC error
can be checked.
Display: EMC**EDC** **: Number of times of error (Maximum three times)
EMC: Mechanism error
EDC: NO DISC error
• When aging operation is complete, be sure to perform the MC Cold Reset to reset the error history.
14
2) Operation during aging mode
In the aging mode, the program is executed in the following
sequence.
(1) The disc tray opens and closes.
(2) The mechanism accesses DISC 2 and makes an attempt to
read TOC. However, since there are no discs, a message
“CD2 NO DISC” appears.
(3) The mechanism accesses DISC 3 and a message “CD3 NO
DISC” appears.
(4) The disc tray turns to select a disc1.
(5) A disc is chucked.
(6) TOC of disc is read.
(7) The pickup accesses to the track 1, and playing 2 seconds.
(8) The pickup accesses to the last track, and playing 2 seconds.
(9) Every time when an aging operation of step 1 to step 8 is
complete, the display “AGING[*][*][*][*]” value increases
as the number of aging operations is counted up.
(10) Returns to step 1.
3. Aging Mode in Tape Deck section

1) Display state
• No error occurs
Display action now
• Error occurred
Display action last time
NO. Display action Action contents Final timing

1 TAPE A AG-1 Rewind the TAPE A, B The top of tape
2 TAPE A AG-2 FWD play the TAPE A 2 minutes playing
3 TAPE A AG-3 F.F. the TAPE A 20 second FF or the end
of tape
4 TAPE A AG-4 REV play the TAPE A 2 minutes playing
5 TAPE A AG-5 Rewind the TAPE A The top of tape
6 TAPE B AG-2 FWD play the TAPE B 2 minutes playing
7 TAPE B AG-3 F.F. the TAPE B 20 second FF or the end
of tape
8 TAPE B AG-4 REV play the TAPE B 2 minutes playing
9 TAPE B AG-5 Rewind the TAPE B The top of tape
2) Operation during aging mode

In the aging mode, the program is executed in the following
sequence.
(1) Rewind is executed up to the top of tape A and B.
(2) A tape on FWD side is played for 2 minutes.
(3) FF is executed up to either made for 20 second or the end of
tape.
(4) A tape is reversed, and the tape on REV side is played for 2
minutes.
(5) Rewind is executed up to the top of tape.
(6) Returns to step 2, and repeat steps from 2 to 5.
[Function Change Mode]

* elect either VIDEO or MD of the external FUNCTION input.
Procedure:
1. Turn on the power.
2. Press the two buttons ENTER and ?/1 at the same time.
The main power is turned on and the other function of the
previous function is selected and displayed. “MD” or
“VIDEO”.
15
SECTION 5 SECTION 6
MECHANICAL ADJUSTMENTS ELECTRICAL ADJUSTMENTS
Precaution
DECK SECTION 0 dB=0.775 V
1. Clean the following parts with a denatured alcohol-moistened
swab: 1. Demagnetize the record/playback head with a head
record/playback heads pinch rollers demagnetizer.
erase head rubber belts 2. Do not use a magnetized screwdriver for the adjustments.
capstan idlers 3. After the adjustments, apply suitable locking compound to the
2. Demagnetize the record/playback head with a head parts adjust.
demagnetizer. 4. The adjustments should be performed with the rated power
3. Do not use a magnetized screwdriver for the adjustments. supply voltage unless otherwise noted.
4. After the adjustments, apply suitable locking compound to the 5. The adjustments should be performed in the order given in this
parts adjusted. service manual. (As a general rule, playback circuit adjustment
5. The adjustments should be performed with the rated power should be completed before performing recording circuit
supply voltage unless otherwise noted. adjustment.)
6. The adjustments should be performed for both L-CH and R-
Torque Measurement CH.
Mode Torque meter Meter reading 7. Switches and controls should be set as follows unless otherwise
specified.
FWD 31 to 71 g • cm
CQ-102C
(0.43 – 0.98 oz • inch) • Test Tape
FWD 2 to 6 g • cm
CQ-102C Tape Signal Used for
back tension (0.02 – 0.08 oz • inch)
31 to 71 g • cm P-4-A100 10 kHz, –10 dB Azimuth Adjustment
REV CQ-102RC WS-48B 3 kHz, 0 dB Tape Speed Adjustment
(0.43 – 0.98 oz • inch)
REV 2 to 6 g • cm P-4-L300 315 Hz, 0 dB Level Adjustment
CQ-102RC
back tension (0.02 – 0.08 oz • inch)
71 to 143 g • cm Record/Playback Head Azimuth Adjustment
FF/REW CQ-201B
(0.98 – 1.99 oz • inch)
DECK A DECK B
100 g or more
FWD tension CQ-403A
(3.53 oz or more) Note: Perform this adjustments for both decks
100 g or more Procedure:
REV tension CQ-403R 1. Mode: Playback
(3.53 oz or more)
test tape main board

P-4-A100 CN301
(10 kHz, –10 dB) Pin 3 (L-CH)
Pin 1 (R-CH) level meter
set
+
–
main board
CN301
Pin 2 (GND)
16
2. Turn the adjustment screw and check output peaks. If the peaks Tape Speed Adjustment DECK B
do not match for L-CH and R-CH, turn the adjustment screw Note: Start the Tape Speed adjustment as below after setting to the test
so that outputs match within 1dB of peak. mode.
In the test mode, the tape speed is high during pressing the
SD SYNC HI-DUB button.
Procedure:
within 1. Turn the power switch on.
L-CH 1dB 2. Press the x button, ENTER button and DISC 3 button
peak
within simultaneously.
Output 1dB (The “TEST MODE” on the fluorescent indicator tube display
level
while in the test mode.)
To exit from the test mode, press the ?/1 button.
R-CH Mode: Playback
peak
Screw Screw test tape
position L-CH R-CH position WS-48B frequency counter
peak peak (3 kHz, 0 dB)
set +
3. Mode: Playback –
test tape main board
P-4-A100
(10 kHz, –10 dB) oscilloscope CN301 (Pin 3 : L-CH)
pin 3 (Pin 1 : R-CH)
L-CH
pin 2
MAIN L 1. Insert the WS-48B into the deck B.
board V H
CN301 2. Press the gG button on the deck B.
set R 3. Press the SD SYNC HI-DUB button in playback mode.
Then at HIGH speed mode.
R-CH
4. Adjust RV1001 on the LEAF SW board do that frequency
pin 1
counter reads 6,000 ± 30 Hz.
waveform of oscilloscope
5. Press the SD SYNC HI-DUB button.
Then back to NORMAL speed mode.
6. Adjust RV1002 on the LEAF SW board so that frequency
in phase 45 ° 90 ° 135 ° 180 ° counter reads 3,000 ± 15 Hz.
Adjustment Location: LEAF SW board
good wrong
Playback level Adjustment DECK A DECK B

4. After the adjustments, apply suitable locking compound to the Procedure:
pats adjusted. Mode: Playback
test tape
Adjustment Location: Playback Head (Deck A). P-4-L300 level meter
Record/Playback/Erase Head (Deck B). (315 Hz, 0 dB)
set +
–
main board
CN301 (Pin 3 : L-CH)
(Pin 1 : R-CH)
Deck A is RV302 (L-CH) and RV352 (R-CH), Deck B is RV303

(L-CH) and RV353 (R-CH) so that adjustment within adjustment
level as follows.
Adjustment Level:
CN301 PB level: 301.5 to 338.3 mV (–8.2 to –7.2 dB) level
difference between the channels: within ±0.5 dB
Adjustment Location: MAIN board
Sample Volue of Wow and Flutter: 0.3% or less W. RMS

(WS-48B)
forward
reverse
17
REC Bias Adjustment DECK B 4. Mode: Record
Procedure:
INTRODUCTION MD/VIDEO (AUDIO) IN
When set to the test mode performed in Tape Speed Adjustment, 315 Hz, 50 mV (–23.8 dB)
when the tape is rewound after recording, the “REC memory mode” AF OSC
blank tape
which rewinds only the recorded portion and playback is set. 600 Ω CS-123
This “REC memory mode” is convenient for performing this attenuator
adjustment. During recording, the input signal FUNCTION will set
automatically switch to VIDEO.
(If do not operation of stopped from recording complete, and rotette
of shuttle knob then rewind to recording start position.) 5. Mode: Playback
1. Press MD/VIDEO button to select VIDEO. (This step is not recorded level meter
portion
necessary if the above test mode has already been set.)
2. Insert a tape into deck B. +
3. After press REC PAUSE/START button, press REC PAUSE/ set
–
START button, then recording start.
4. Mode: Record CN301 (Pin 3 : L-CH)
(Pin 1 : R-CH)
6. Confirm playback the signal recorded in step 3 become

MD/VIDEO (AUDIO) IN adjustable level as follows.
1) 315 Hz  50 mV (–23.8 dB) If these levels do not adjustable level, adjustment the RV301

2) 10 kHz  (L-CH) and RV351 (R-CH) on the MAIN board to repeat steps
AF OSC blank tape 4 and 5.
600 Ω CN-123 Adjustable level:
attenuator CN301 PB level: 47.2 to 53.0 mV (–24.3 to –23.3 dB)
set Adjustment Location: MAIN board
5. Mode: Playback [MAIN BOARD] (Component Side)
recorded level meter

portion
set +
– T601
REC LEVEL (L)

CN301 (Pin 3 : L-CH) RV611 (B) PB LEVEL (L)
(Pin 1 : R-CH) (A)
CN304
6. Confirm playback the signal recorded in step 3 become CN301
adjustable level as follows. PB LEVEL (R) 3 1 RV301

(A)
If these levels do not adjustable level, adjustment the RV304 PB LEVEL (R)
RV302
CN302
(L-CH) and RV354 (R-CH) on the AUDIO board to repeat steps (B)
RV352
RV353
4 and 5. RV351 RV303
Adjustable level: Playback output of 315 Hz to playback output CN303
REC LEVEL (R) PB LEVEL (L)
of 10 kHz: ±1.0 dB (B) (B) RV304
Adjustment Location: MAIN board REC LEVEL (L)
(A) REC LEVEL (R) RV354
REC Level Adjustment DECK B (A)

Procedure:
INTRODUCTION [LEAF SW BOARD] (Component Side)
When set to the test mode performed in Tape Speed Adjustment,
TAPE SPEED
when the tape is rewound after recording, the “REC memory mode”










which rewinds only the recorded portion and playback is set. (NORMAL) (HIGH)
This “REC memory mode” is convenient for performing this
adjustment. During recording, the input signal FUNCTION will RV1002 CN1001
RV1001
automatically switch to VIDEO.
(If do not operation of stopped from recording complete, and rotate
of shuttle knob then rewind to recording start position.)
1. Press MD/VIDEO button to select VIDEO. (This step is not

necessary if the above test mode has already been set.)
2. Insert a tape into deck B.
3. After press REC PAUSE/START button, press REC PAUSE/
START button, then recording start.
18
FM Tuned Level Adjustment CD SECTION
FM RF SSG Note :
75 Ω coaxial 1. CD Block is basically designed to operate without adjustment.
Therefore, check each item in order given.
2. Use YEDS-18 disc (3-702-101-01) unless otherwise indicated.
3. Use an oscilloscope with more than 10MΩ impedance.
set 4. Clean the object lens by an applicator with neutral detergent
Carrier frequency : 98 MHz when the signal level is low than specified value with the
Modulation : AUDIO 1 kHz, 75 kHz FM ANTENNA terminal following checks.
deviation (100%) (TM601)
Output level : 28 dB (at 75 W open)
S-Curve Check
Procedure: Oscilloscope
1. Supply a 28 dB 98 MHz signal from the ANTENNA terminal. BD board
2. Tune the set to 98 MHz.
3. Adjust RV611 to the point (moment) when the TUNED TP(FEO)
indicator will change from going off to going on. TP(VC)
Adjustment Location: MAIN board Procedure :

1. Connect oscilloscope to TP (FEO).
Null Adjustment 2. Connect between TP (FEI) and TP (VC) by lead wire.
3. Connect between TP (AGCCON) and TP (GND) by lead wire.
FM RF SSG 4. Turn Power switch on.
5. Load a disc (YEDS-18) and actuate the focus search. (In
75 Ω coaxial consequence of open and close the disc tray, actuate the focus
search)
6. Confirm that the oscilloscope waveform (S-curve) is
set symmetrical between A and B. And confirm peak to peak level
Carrier frequency : 98 MHz within 4 ±1 Vp-p.
Modulation : AUDIO 1 kHz, 75 kHz FM ANTENNA terminal
deviation (100%) (TM601) S-curve waveform
Output level : 60 dB (at 75 W open)
symmetry
Procedure:
1. Supply a 60 dB 98 MHz signal from the ANTENNA terminal. A
2. Tune the set to 98 MHz.
within 4 ±1Vp-p
3. Measure voltage between pin 21 of IC 601. Adjust T601 ubtil
B
the voltage becomes 0 V.
Adjustment Location: MAIN board 7. After check, remove the lead wire connected in step 2 and 3.
Note : • Try to measure several times to make sure than the ratio
of A : B or B : A is more than 10 : 7.
Adjustment Location • Take sweep time as long as possible and light up the
brightness to obtain best waveform.
[MAIN BOARD] Component side
RF Level Check
NULL
oscilloscope
BD board
FM TUNED LEVEL
T601
TP(RF)
TP(VC)
RV611
Procedure :
CN304 1. Connect oscilloscope to TP (RF).
CN301
2. Connect between TP (AGCCON) and TP (GND) by lead wire.
3 1 RV301
3. Turned Power switch on.
RV302
RV352 CN302 4. Load a disc (YEDS-18) and playback.
RV353 5. Confirm that oscilloscope waveform is clear and check RF signal
RV303
RV351 level is correct or not.
CN303
6. After check, remove the lead wire connected in step 2.
RV304
RV354
19
Note : Clear RF signal waveform means that the shape “ ◊ ” can be clearly Adjustment Location:
distinguished at the center of the waveform.
[BD BOARD] (Conductor Side)
RF signal waveform
VOLT/DIV : 200mV
TIME/DIV : 500ns
level : 1.45 ± 0.3Vp-p
E-F Balance (1 Track jump) Check
oscilloscope
BD board
TP
TP(TEO) TP
(XPCK)
TP(VC) (AGCCON)
12
1 21 20
TP IC103
Procedure : (TEO) 24
1. Connect oscilloscope to TP (TEO) and TP (VC). 40 1
TP IC101
2. Turned Power switch on. (FEO) 41 80
3. Load a disc (YEDS-18) and playback the number five track. TP
TP (FEI)
4. Press the gG button. (Becomes the 1 track jump mode.) 60 61
5. Confirm that the level B and A (DC voltage) on the oscilloscope (VC)
waveform. TP
(RF) TP
1 track jump waveform center of (DGND)
waveform
A (DC voltage)
0V
level=1.3±0.6Vp-p symmetry
A × 100=less than ±22%

Specified level: ––
B
6. After check, remove the lead wire connected in step 1.
RF PLL Free-run Frequency Check

Procedure :
1. Connect frequency counter to test point (XPCK) with lead wire.
frequency counter
BD board
TP (XPCK)
2. Turned Power switch on.

3. Put the disc (YEDS-18) in to play the number five track.
Confirm that reading on frequency counter is 4.3218MHz.
20
HCD-BX3/DX3
SECTION 7
DIAGRAMS
7-1. CIRCUIT BOARD LOCATION
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is printed in each block.)
Note on Schematic Diagram: Note on Printed Wiring Boards: MOTOR Board DRIVER Board
• All capacitors are in µF unless otherwise noted. pF: µµF • X : parts extracted from the component side.
50 WV or less are not indicated except for electrolytics • b : Pattern from the side which enables seeing. ADDRESS SENSOR Board
and tantalums. • Indication of transistor. SUB-TRANS Board
• All resistors are in Ω and 1/4 W or less unless otherwise
C
specified. TRANS Board BD Board
• ¢ : internal component. These are omitted. Q
• C : panel designation.
B E
Note: Note:
The components identi- Les composants identifiés par
fied by mark ! or dotted une marque ! sont critiques Q
line with mark ! are criti- pour la sécurité.
cal for safety. Ne les remplacer que par une
piéce portant le numéro B C E
Replace only with part
number specified. spécifié. These are omitted.
PANEL Board
• U : B+ Line.
• V : B– Line.
• H : adjustment for repair. MAIN Board
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal produc- LEAF SW Board
tion tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal produc-
tion tolerances.
• Circled numbers refer to waveforms. AMP Board
HEAD (A) Board
• Signal path.
F : FM
f : AM HEAD (B) Board
E : PB (DECK A)
d : PB (DECK B)
G : REC (DECK B)
J : CD
c : digital out
• Abbreviation
CND : Canadian model
AUS : Australian model
G : German model
AED : North European model
EA : Saudi Arabia model • WAVEFORMS
MY : Malaysia model
SP : Singapore model – BD BOARD – – MAIN BOARD – – PANEL BOARD –
TH : Thai model
TW : Taiwan model 1 IC101 yj 3 IC101 ra 1 T301 4 REC MODE 1 IC601 oa STOP MODE
KR : Korea model CD PLAY MODE CD PLAY MODE
MX : Mexican model
AR : Argentina model
approx 200mVp-p 135Vp-p 5.2Vp-p

6.4Vp-p 81kHz 12.5MHz
16.9344MHz
2 IC101 ta 4 IC101 el 2 IC401 qd STOP MODE

CD PLAY MODE CD PLAY MODE
approx 170mVp-p
16.0MHz 4.0Vp-p
400nsec/div 1.2Vp-p
3 IC401 qa STOP MODE
32.768kHz 3.0Vp-p
21 21
HCD-BX3/DX3
7-2. BLOCK DIAGRAMS AR,AUS,E,EA,KR,MX,MY,SP,TH,TW MODEL
AM/FM IF MPX
TM601 FE601 Q601 IC601 LPF601
TUNER/CD SECTION
CF601 RF IF CF602 BUFFER L-CH • RCH is omitted
1 ANT IN IF OUT 7
AMP
1 FM IF L OUT 11
Q611
LPF A • Signal Path
FM 75Ω OSC OUT 8
JR609 MAIN
VT 5 R OUT 10 R-CH SECTION : FM
Q602
G US,CND MODEL +B A+12V : CD
AM IF IN 18
FE602 IFT601
AM PLL : DIGITAL OUT
8 ANT IN IF OUT 1 IC651
AM MIX OUT 19
F OUT 3
10 FM FM/AM IF 12 9 IF OUT
VT 4
FM 7 12 AM/IF FM SD ADJ 3
1 XIN AM OSC 14 24 AM OSC RV611
AED,AEP,CIS,G,UK MODEL X651 AED,AEP,CIS,G,UK ONLY
VCO STOP 2 13 VCO STOP
FE603 4.5MHz RDS
24 XOUT IF REQ 8 8 IF REQ MUTE IC682 MASTER CONTROL
IC681 IC401(1/2)
1 ANT IN IF OUT 7 3 1
DO FM/AM DET 16 4 MUX
OSC OUT 8 15 FM OSC DO 6
DI DATA 2 21 RDS DATA
VT 5 18 VT1 IN DI 4 14 XO
CL XT681 INT 16 20 RDS INT
17 VT1 CL 5 4.332MHz
CE
19 PD1 CE 3 13 XI
20 AM RF IN
RB641 13 14
1 4 11 15 9
22 AM OSC TUNED 6 24 TUNED
5
STEREO 7 23 STEREO
3 6 7
23 V REG
22 ST MUTE
2 12
DO
27 ST DIN
DI
26 ST DOUT
CL
28 ST CLK
CE
25 ST CE
OPTICAL PICK-UP DIGITAL SERVO

DIGITAL SIGNAL PROC.
BLOCK RF AMP D/A CONV. IC201
(KSS-213F) IC103 IC101
OPTICAL CD
VC 12 VC D OUT 60 DIGITAL
OUT DIITAL OUT
+5V
A
5 A RFO 16 51 RFAC
B
6 B RFI 17 43 RFDC
C L OUT
D
7 C L OUT 72 B IC701
8 D FE 14 39 FE
E MAIN
11 E TE 13 41 TE R OUT 75 R-CH SECTION LOAD IN 44 9 4
F MOTOR M721
10 F 40 SE M TURN
Q101 DRIVE MOTOR
LOAD OUT 45 7 2
LD LD
3 LD LD ON 22 14 XLON DATA 5 35 CD DATA
DRIVE
CLOK 7 37 CD CLK
GND XLAT 6 42 XLT
IC711
HOLD SW 21 SQCK 2 33 SQ CLK
TBL ADDRESS
SCLK 9 T SENS 49
PD SENSOR
4 PD SCOR 20 19 SCOR
VR SQSO 1 32 SQ DATA
IC102 SENS 8 40 SENS
MOTOR/COIL DRIVE
F+ OPEN SW 46 S701
13 CH1RO CH1RI 3 32 FFDR OPEN/CLOSE
FOCUS CLOSE SW 47
COIL F- S101
14 CH1FO CH1FI 2 33 FRDR SSTP 27 LIMIT
IN SW S711
BU UP/DOWN SW 48 UP/DOWN
T+
11 CH2RO CH2RI 6 30 TFDR
TRACKING
XTAI 66
COIL T- X101
12 CH2FO CH2FI 5 31 TRDR
16 16.9344MHz
XTAO 67
18 CH3RO CH3RI 23 29 SRDR
M102
SLED M
MOTOR
17 CH3FO CH3FI 24 28 SFDR
XRST 3 43 XRST
16 CH4RO CH4INS 25 26 MDP
M101
SPINDLE M
MOTOR
15 CH4FO 41 HOLD
MUTE 20
22 22
HCD-BX3/DX3
MAIN SECTION
EXCEPT
US,CND MODEL
INPUT SELECT
TONE/VOL CONT
IC101
IC102 IC501 TM801
L-CH 5
TUNER
SECTION A 40 IN2A VOL OUT2 24
6
7
1 POWER 6 L
Q504,505 AMP Q861 Q821,822 SPEAKER
Q824,825 RY801
LOUT MUTE MUTE MUTE MUTE PROTECT R CH R
CD
SECTION B 38 IN2C
CONT Q103 12 CONT Q862 DETECTOR RELAY
DRIVE
Q101,102 Q551 Q823 Q828,829
J101 D841 D582-583
DBFB OVER LOAD PROTECT PROTECT
L-CH CONT DETECTOR CONT SWITCH R CH
L 37 IN2D
MD/VIDEO Q503,504 J631
(AUDIO) MUTE MUTE +B Q582,583 PHONS
R R-CH Q503 CONT Q581 OVER HEAT
DBFB DETECTOR
DECK PROC. SWITCH AR,AUS,E,EA,KR
IC301 AR,AUS,E,EA,KR MX,MY,SP,TH,TW
AED,AEP,CIS,CND
G,UK,US MODEL MX,MY,SP,TH,TW MODEL Q961,962 FAN
MODEL AR,AUS,E,EA,KR
REC JR907 FAN MX,MY,SP,TH,TW
43 35 INVOL OUT2 DRIVE
PB EQ MODEL
DECK-A AMP
RV302
IC303 IC104
5 7 3 FL601
48 REC 1
HP901 DOLBY 2 FLOURESCENT
PB B INDICATOR TUBE
HEAD 70
A PB DISPLAY CONTROL
PB EQ DOL PB IC601
R-CH AMP 40 39 IN2B
RV303 PAS
IC304 B AR,AUS,E,EA,KR 3 HEADPHONE
5 7 120 MX,MY,SP,TW MODEL F1 F2
46 50
.
21 DATA P1
REC/PB SWITCH 52
DECK-B IC302 22 CLOCK P35
85 Q606-614
1 G1 49 LED
IC602 33 DRIVER
G17
HRPE901 6 SPEANA 17 20 BPF 0
REC/PB 2 SWITCH BPF
4 R-CH 5 12 25 BPF 5
HEAD Q304,305
AR,AUS,E,EA,KR 4
RV722 11 26 ALL BAND TUNER 5
R-CH 3 MX,MY,SP,TH,TW 3
MODEL MIC CD 6 D614-620
R CH Q624-630
C332,L301 J721 IC722 VOL TAPE A/B 7
3 IC722 S623-633 LED
BIAS REC MIC 1 1 6 MD/VIDEO 8 DRIVER
TRAP 36 38 39 2 7 FUCTION
RV304 EQ 5 17 KEY0 GROOVE 11
KEY
B NORM/CROM/METAL
R-CH REC RV301 LIMITER REC/PAUSE 15
BIAS Q721 S619-621
REC(L) SURROUND 16
LEVEL FUCTION
18 KEY1
REC /PB/PASS
T301 TA+12V KEY
BIAS ON/OFF
NORM/HIGH
ALC ON/OFF
RM ON/OFF
BIAS
LM ON/OFF
NR ON/OFF
NORM
OSC S637-646
A120/70
33
MS OUT
BIAS
PB A/B
ERASE Q302,303 CROM SW S647 Q604
Q301 32
HEAD LED D601
AR,AUS,E,EA,KR FUCTION STANDBY 28 DRIVER
17 19 16 18 15 20 22 23 24 25 26 MX,MY,SP,TH,TW KEY 19 KEY2 STANDBY
MODEL Q605
D602
LED
S601 1 VOL A TIMER 27 DRIVER TIMER
Q141
VOLUME 2 VOL B
DC
+6V A+12V
BIAS
SIRCS
100 SIRCS
D822 IC603 XIN 89
X601
12.5MHz
97 I2C DATA XOUT 90
98 I2CCLOCK
S1004 96 WAKE UP
A 120/70 X401 X402 92 RESET
32.768kHz 16MHz
Q972
79 77 76 78 75 74 73 72 71 70 4 5 10 11 15 13 83 84 100 87 82 30 29 18 7
S1001 -V T971
68 A PLAY VP
DBFB ON/OFF
REC MUTE
NR ON/OFF
DATA
IIC CLK
WAKE UP
TC RELAY
ALC
TC MUTE
CLK
X IN
EQ H/N
BIAS
X OUT
LINE MUTE
AC CUT
R/PB PAS
XC OUT
IIC DATA
PB A/B
STK MUTE
RELAY H
PROTECT
XC IN
AMS IN
A PLAY REG
S1002
B PLAY 69 B PLAY
D541
S1003 67 A HALF
IC911 Q911,912 +B
A HALF D+5V(SW) AR,AUS,E,EA AR,E,EA,KR,MY
POWER
+5V CD POWER AMP MY,SP,TW MODEL SP,TH,TW MODEL
S1006 93 B HALF A+5V(SW) 3 1
REG SWITCH -B F973
B HALF
S1005 CD POWER 85 S971

REC A D901-904
D953 IC951
RDS D+5V F972
S1009 MASTER CONTROL D952 +5V
REC B IC401(2/2) AUDIO +5V 3 1
REG
IC1001 A+12V
• RCH is omitted F971 AR,E,EA,MY
A REEL TC A+12V D508 SP,TW MODEL
• Signal Path 90 A SHUT IC921
DET MIC A+12V JW972
D543 D542
+12V
IC1002 ST A+12V 3 1
: PB (DECK A) REG AUS,KR,TH MODEL
B REEL D906-909
91 B SHUT IC971
DET
: PB (DECK B) Q393,394 +9V
TC M+9V 3 1
A TRIG REG
57 A TRIG D931-933
: REC (DECK B) DRIVE M+7V(UNSW)
STBY RELAY
A TRG M+
LED +7V F1
Q391,392
CAP M CONT
RESET
: FM
CAP M H/L
B TRIG
58 B TRIG F2
DRIVE
: CD B TRG M+ 81 12
59 60
D972-975 T972
16 Q1001 Q395 IC501 IC971
Q501 D506
MOTOR CAP MOTOR EVER +5.6V +5.6V AC
RESET 3 1
CONT SPEED CONT REG IN
RV1002
NORM S Q971 RY971
RV1001 RELAY
M901 HIGH S Q396,397 DRIVE
CAPSTAN AED,AEP,CIS,CND,G,UK,US MODEL
M CAP MOTOR
MOTOR
DRIVE
23 23
HCD-BX3/DX3
7-3. PRINTED WIRING BOARD BD SECTION • See page page 21 for Circuit Boards Location.
• Semiconductor
Location 1 2 3 4 5 6
Ref. No. Location
IC101 D-2
IC102 C-4
IC103 B-3
A
Q101 A-4
F (Page 26)
24 24
HCD-BX3/DX3
7-4. SCHEMATIC DIAGRAM BD SECTION • See page page 21 for Wavefoms.
• See page page 42 for IC Block Diagrams.
(Page 28)
The components identified by Les composants identifiés par

mark 0 or dotted line with mark une marque 0 sont critiques
0 are critical for safety. pour la sécurité.
Replace only with part number Ne les remplacer que par une
specified. pièce portant le numéro spécifié.
25 25
HCD-BX3/DX3
7-5. PRINTED WIRING BOARD MAIN SECTION • See page page 21 for Circuit Boards Location.
• Semiconductor
Location 1 2 3 4 5 6 7 8 9
Ref. No. Location (Page 36) (Page 24)
D501 B-4
D502 A-4
D503
D504
A-4
A-3 A
D505 A-3
D506 A-4
D508 C-1
D509 A-3
D510 A-3
D511 B-1
D601 B-8
D641 C-9
D651 B-7 (Page 32)
D681
D822
D-7
E-8
B
D841 E-8
D861 E-7
D901 F-7
D902 F-7
D903 F-7
D904 F-7
D906 F-8
D907 F-8
D908 F-8
D909 F-8 C
D931 F-5
D932 F-5
D933 F-5
D951 F-5
D952 E-6
D953 E-6
D961 F-9
IC101 D-6
IC102
IC104
C-4
B-5 D
IC201 A-9
IC301 E-4
IC302 F-3
IC303 E-2 (Page 34)
IC304 F-3
IC401 B-3
IC501 B-4
IC601 C-8
IC651 A-8
IC681
IC682
C-7
D-7
E
IC911 B-6
IC921 F-6
IC951 F-5
IC971 F-4
(Page 34)
Q101 D-6
Q102 C-5
Q103 G-5
Q141 C-4
Q301 F-4 F
Q302 G-4
Q304 F-3
(Page 34)
Q391 D-2
Q392 C-2
Q393 D-2
Q394 C-2
Q395 D-2
Q396 D-2
Q397 C-1
Q504
Q601
C-3
B-7 G
Q611 C-7
Q612 C-7
Q821 E-8
Q822 E-8
Q824 D-8
Q825 D-8
Q828 D-8
Q861 E-7
(Page 30) (Page 30)
26 26
HCD-BX3/DX3
7-6. SCHEMATIC DIAGRAM MAIN SECTION (1/3) • See page page 44 for IC Block Diagrams.
12
(Page 28)
27 27
HCD-BX3/DX3
7-7. SCHEMATIC DIAGRAM MAIN SECTION (2/3) • See page page 44 for IC Block Diagrams.
(Page 27)
(Page 31) (Page 31)
W2
(Page 25)
(Page 37)
(Page 29)
(Page 29)
(Page 29)
28 28 (Page 33)
HCD-BX3/DX3
7-8. SCHEMATIC DIAGRAM MAIN SECTION (3/3) • See page page 21 for Wavefoms.
• See page page 40 for IC Pin Function Description.
(Page 28) (Page 28) (Page 28)

(Page 28)
2.2K
C444
1000P
2.2K
(Page 28)
3 2
(Page 35)
29 29
HCD-BX3/DX3
7-9. PRINTED WIRING BOARD AMP SECTION • See page page 21 for Circuit Boards Location.
• Semiconductor
Location 1 2 3 4 5 6 7 8 9
Ref. No. Location
D501 D-3
D502 D-5
D541
D542
B-4
E-7 A
D543 E-7
D551 D-5
IC501 F-3
Q501 E-3
Q503 D-3
Q504 D-4
Q551 E-5
Q581 E-4 B
Q582 D-3
Q583 D-2
(Page 38)
(Page 26)
D
(Page 26)
30 30
HCD-BX3/DX3
7-10. SCHEMATIC DIAGRAM AMP SECTION
(Page 39)
C544
1000
25V

(Page 28) (Page 28)

31 31
HCD-BX3/DX3
7-11. PRINTED WIRING BOARD PANEL SECTION • See page page 21 for Circuit Boards Location.
1 2 3 4 5 6 7 8 9 10
(Page 26)
• Semiconductor Location
F Ref. No. Location Ref. No. Location
D601 B-10 Q606 B-6
D602 A-8 Q607 B-7
D614 E-4 Q608 B-7
D615 E-4 Q609 B-7
D616 E-4 Q610 B-7
D617 E-7 Q611 B-7
D618 E-6 Q612 B-7
D619 E-5 Q613 B-7
D620 E-5 Q614 B-8
Q624 D-4
IC601 B-5 Q625 D-4
IC602 C-6 Q626 D-4
IC603 B-8 Q627 E-6
IC722 D-10 Q628 E-6
Q629 E-5
Q604 B-10 Q630 E-5
Q605 A-9 Q721 C-9
32 32
HCD-BX3/DX3
7-12. SCHEMATIC DIAGRAM PANEL SECTION • See page page 21 for Wavefoms.
• See page page 41 for IC Pin Function Description.
0.47 1
C617 10000P
1
C697 100P
(Page 28)
100 100
10V 10V

33 33
HCD-BX3/DX3
7-13. PRINTED WIRING BOARD LEAF SW SECTION • See page page 21 for Circuit Boards Location.
• Semiconductor
Location
Ref. No. Location
1 2 3 4 5 6
D1001 A-2
D1002 A-5
IC1001 A-1
IC1002 A-5
Q1001 A-2 A
B
(Page 26)
(Page 26) (Page 26)
34 34
HCD-BX3/DX3
7-14. SCHEMATIC DIAGRAM LEAF SW SECTION
(Page 29)
35 35
HCD-BX3/DX3
7-15. PRINTED WIRING BOARD DRIVER SECTION • See page page 21 for Circuit Boards Location.
• Semiconductor
Location 1 2 3 4 5 6
Ref. No. Location
D701 E-1
IC701 E-1
A
IC711 B-5
G (Page 26)
36 36
HCD-BX3/DX3
7-16. SCHEMATIC DIAGRAM LEAF SW SECTION • See page page 43 for IC Block Diagrams.
(Page 28)
37 37
HCD-BX3/DX3
7-17. PRINTED WIRING BOARD TRANS SECTION • See page page 21 for Circuit Boards Location.
• Semiconductor
Location 1 2 3 4 5 6 7 8 9
Ref. No. Location
D971 E-4
D972 G-2
D973
D974
F-2
G-3
A
D975 F-3
D977 C-6
D978 C-8
D979 C-8
IC971 F-3
Q971 F-3
Q972 D-8
B
(Page 30)
H 38 38
HCD-BX3/DX3
7-18. SCHEMATIC DIAGRAM TRANS SECTION
(Page 31)
C975
0.1

39 39
7-19. IC PIN FUNCTION DESCRIPTION
• MAIN BOARD IC401 M30622MAA-A25FP (MASTER CONTROL)
Pin No. Pin Name I/O Description Pin No. Pin Name I/O Description
1 SURROUND 1 O Not used. 51 N.C I Not used.
4 498-DATA O Data signal output for IC101 (M61504FP) 54 N.C I Not used.
5 498-CLK O Clock signal output for IC101 (M61504FP) 55 N.C I Not used.
6 N.C I Not used. 56 N.C I Not used.
7 AC-CUT I AC CUT ON (L) / OFF (H) CHECK 57 A TRIG O A deck trigger control signal output.H=ON, L-OFF
8 GND — Connected to ground. 58 B TRIG O B deck trigger control signal output.H=ON, L-OFF
9 GND — Connected to ground. 59 CAPM-H/L O Capstan motor High/Low speed control signal output.
10 XC IN I SUB CLOCK input. (32.768kHz) 60 CAPM-CONT O Capstan motor REV/FWD/STOP control signal output.H=REV, L=FWD/STOP
11 XC OUT O SUB CLOCK output. (32.768kHz) 61 N.C I Not used.
12 RESET I System reset input. 62 VCC — POWER SUPPLY (+5V)
13 X-OUT O MAIN SYSTEM CLOCK output. (16MHz) 63 N.C I Not used.
14 VSS — Vss 64 VSS — Ground.
15 X-IN I MAIN SYSTEM CLOCK input. (16MHz) 65 N.C I Not used.
16 VCC — Power supply. (+5V) 66 N.C I Not used.
17 NMI I PULL UP (EVER +5V) 67 A HALF I A deck half detect signal input.
18 WAKE_UP I WAKE UP signal input. (L) 68 A PLAY I A deck play detect signal input.
19 SCOR I CD Q-data request signal input. 69 B PLAY I B deck play detect signal input.
20 RDS-INT I RDS interrupt signal input. 70 AMS-IN I AMS signal input. L=ON,H=OFF
21 RDS-DATA I RDS data signal input. 71 TC-MUTE O Tape deck line mute ON/OFF signal output. H=ON, L=OFF
22 ST-MUTE O Tuner mute signal output. 72 R/PB/PAS I REC/PB/PASS select signal input.
23 STEREO I STEREO detect signal input. L=ON, H=OF 73 NR-ON/OFF O DOLBY NR ON/OFF signal output. H=ON, L=OFF
24 TUNED I TUNED detect signal input. L=ON, H=OFF 74 REC-MUTE O REC mute ON/OFF signal output. L=ON, H=OFF
25 ST-CE O TUNER chip eneble output. 75 BAIS O BIAS ON/OFF signal output.H=ON, L=OFF
26 ST-DOUT O TUNER data output. 76 EQ-H/N O EQ High/Normal select signal output. H=High, L=Normal
27 ST-DIN I TUNER data input. 77 PB-A/B O Playback deckA/B select signal output. H=deckB, L=deckA
28 ST-CLK O TUNER clock signal output. 78 ALC O ALC ON/OFF signal output. L=ON, H=OFF
29 IIC_CLK O IIC SCL output. 79 TC-RELAY O Tape deck relay ON/OFF signal output. H=ON, L=OFF
30 IIC_DATA O IIC SDA output. 80 N.C I Not used.
31 TXDI — Not used. 81 STBY-RELAY O STANDBY relay control signal output.
32 SQ-DATA I Subcode Q data input. (CD data) 82 PROTECT I Speaker protect signal input. L=ON, H=OFF
33 SQ-CLK I Subcode Q data input. (CD clock) 83 DBFB-ON/OFF I Not used.
34 RST1 I Not used. 84 LINE-MUTE O Line mute signal output. L=ON, H=OFF
35 CD-DATA O CD data input. 85 CD-POWER O CD-POWER ON/OFF signal output. H=ON, L=OFF
36 N.C I Not used. 86 F-SHIFT O Not used.
37 CD-CLK O CD clock input. 87 RELAY-H O Speaker terminal relay control signal output. H=ON, L=OFF
38 N.C I Not used. 88 POWER O POWER ON/OFF signal output. H=ON, L=OFF
39 CLOCK-OUT I Clock check signal input. 89 N.C O Not used.
40 SENS I BD condition signal input. 90 A SHUT O A deck reel pulse detect signal output.
41 HOLD O MODE signal input. 91 B SHUT O B deck reel pulse detect signal output.
42 XLT O CD latch signal output. 92 SOFT-TEST O Not used.
43 XRST O CD reset signal output. 93 B HALF O B deck half detect signal input.
44 LOAD-IN I Loading motor control signal input. 94 KEY/CD ADJ O KEY (for jig) / CD adjust.
45 LOAD-OUT O Loading motor control signal output. 95 MODEL-IN I MODEL input.
46 OPEN I Tray open detect signal input. 96 AVSS — Analog ground.
47 CLOSE I Tray close detect signal input. 97 SPEC-IN I Version select signal input.
48 UP/DOWN SW I Pick-up up/down detect signal input. 98 VREF — Analog Reference Voltage
49 T-SENS I CD table detect signal input. 99 AVCC — Analog Power Supply
50 TEST MODE I Not used. 100 STK-MUTE O Power amplifier mute ON/OFF signal output. H=ON, L=OFF
40 40
• PANEL BOARD IC601 TMP88CP77F-1A22 (DISPLAY CONTROL)
Pin No. Pin Name I/O Description

1 VOLUME A I VOLUME A signal input.
2 VOLUME B I VOLUME B signal input.
3 HEADPHONE I Head phone detect signal input. H=ON, L=OFF
4 N.C I Not used.
5 TUNER O TUNER LED driver output.(high active)
6 CD O CD LED driver output.(high active)
7 TAPE A/B O TAPE A/B LED driver output.(high active)
8 MD/VIDEO O MD/VIDEO LED driver output.(high active)
9-10 N.C O Not used.
11 GROOVE O GROOVE LED driver output.(high active)
12-14 N.C O Not used.
15 REC/PAUSE O REC/PAUSE LED driver output.(high active)
16 SURROUND O SURROUND LED driver output.(high active)
17-19 KEY0-2 I KEY input. (AD)
20 Super Low Freq (BPF 0) I BPF input. (AD)
21-25 BPF1-5 I BPF input. (AD)
26 ALL BAND I BPF input. (AD)
27 TIMER O TIMER SEL LED driver output.
28 STANDBY O STANDBY LED output.
29 VSS — Ground.
30 VASS — Ground.
31 AVREF — Analog reference voltage.
32 VDD — Power supply (+5V)
33-49 G17-1 O FL gride signal output.
50 P1 O FL segment signal output.
51 VDD VFT — Power supply (+5V)
52-85 P2-35 O FL segment signal output.
86 N.C I Not used.
87 VKK — –]30V driving power for FL.
88 VDD — Power supply (+5V)
89 Xin I 12.5MHz (Xin)
90 VSS — Ground.
91 Xout O 12.5MHz (Xout)
92 RESET I RESET (low active)
93-94 N.C I Not used.
95 TEST I Connected to ground.
96 WAKE UP O WAKE UP signal output for master controller. (PULL UP)
97 I2C data O IIC SDA
98 I2C clk O IIC SCL
99 N.C I Not used.
100 SIRCS I Remote commander input. (input capture)
41
7-20. IC BLOCK DIAGRAMS
IC101 CXD2587Q (BD BOARD)
AVDD3
AVDD0
AVSS3
AVSS0
DOUT
ASYO
RFDC
RFAC
CLTV
ADIO
IGEN
ASYI
BIAS
FILO
VDD
PCO
VSS
FILI
CE
TE
60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41
40 SE
DIGITAL ERROR DIGITAL ASYMMETRY
INTERNAL BUS
39 FE
OUT CORRECTOR PLL CORRECTION
38 VC
16K
LRCK 61 RAM OPERATIONAL
D/A EFM AMPLIFIER
PCMD 62
INTERFACE DEMODULATOR ANALOG SWITCH
BCK 63
A/D
CONVERTER
EMPH 64
XVDD 65
CLOCK
37 XTSL
XTAI 66 TIMING GENERATOR
36 TES1
XTAO 67 LOGIC
35 TEST
XVSS 68 SERVO DSP PWM GENERATOR 34 VSS
AVDD1 69
AOUT1 FOCUS FOCUS PWM 33 FRDR
70
SERVO GENERATOR 32 FFDR
AIN1 71 SUBCODE
TRACKING TRACKING 31 TRDR
PROCESSOR
SERVO PWM GENERATOR 30 TFDR
LOUT1 72
PWM PWM SLED SLED PWM 29 SRDR
AVSS1 73 SERVO GENERATOR 28 SFDR
AVSS2 74
3rd ORDER 27 SSTP
LOUT2 75 NOISE SHAPER SERVO
DIGITAL 26 MDP
INTERFACE
CLV 25 LOCK
AIN2 76
OVER SAMPLING
AOUT2 77 DIGITAL FILTER MIRR, DFCT, 24 FOK
AVDD2 78 SERVO AUTO FOK 23 DFCT
RMUT 79 SEQUENCER DETECTOR 22 MIRR
SERIAL IN
LMUT 80 INTERFACE
21 COUT
CPU
INTERFACE
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
GFS
SCLK
XLON
SCOR
XLAT
SENS
SPOB
C2PO
XRST
SYSM
WFCK
VDD
SQSO
ATSK
XUGF
SPOA
XPCK
SQCK
CLOK
DATA
IC102 BA5974FP (BD BOARD)

CH3OUTR
CH4OUTR
CH3OUTF
CH4OUTF
POWVCC
CAPAIN3
CH4SIN'
PRFVCC
CH3RIN
CH4BIN
CH4SIN
CH3FIN
MUTE
GND
28 27 26 25 24 23 22 21 20 19 18 17 16 15
F R
R MUTE
INTERFACE
F
LEVEL SHIFT
THERMAL
SHUTDOWN
F
INTERFACE
F R F
R
INTERFACE
R
F R
1 2 3 4 5 6 7 8 9 10 11 12 13 14
VREFOUT
CH1FIN
CH1RIN
CAPAIN1
CH2FIN
CH2RIN
CAPAIN2
GND
VREFIN
POWVCC
CH2OUTR
CH2OUTF
CH1OUTR
CH1OUTF
42
IC103 CXA2568M (BD BOARD) IC602 BA3830F (PANEL BOARD)
APC PD AMP VCC 24 VCC

R02 1 REFFERENCE RESET 18 RESET
VCC 23 LC/PD CURRENT
VEE 22 LD_ON
HOLD 1
P01 2 REFFERENCE 17 f01
VEE CURRENT
AGCVTH 2 VREF
APC LD AMP
LD 3 21 HOLD_SW LINE 3 BPF DET 16 f02
VC 20 AGCCONT NF
VCC (50%/30%
OFF) BPF DET
PD 4
19 RF_BOT LINE
4 15 f03
IN
BPF DET
VC
A 5
REC 5 BPF DET 14 f04
NF
B 6 VEE
18 RFTC BPF DET
RF SUMMING AMP RF_EQ_AMP 17 RF_1 REC 6 13 f05
C 7 VC VC IN
16 RFO
BPF DET
15 RFE
D 8 RESET 7 12 f06
ERROR AMP DET
VC C
FOCUS
VEE 9 VEE
14 FE
BIAS 8 11 REC
VC C Bias LEVEL
VC
F 10
GND1 9 10 VCC
E 11
13 TE
VC
TRACKING
VC
VC BUFFER ERROR AMP
VC 12 VCC
VC
VEE
VC
IC701 BA6956AN (DRIVER BOARD) IC682 BU1924 (MAIN BOARD)

VDD2
RCLK
VSS2
(NC)
XO
T1
T2
XI
16 15 14 13 12 11 10 9
TSD
CLOCK
TEST
CONTROL LOGIC
DEFFERENTIAL BIPHASE PLL PLL 57KHz

1 2 3 4 5 6 7 8 9 DECODER DECODER 1187.5Hz RDS/ARI
VREF
OUT2
RNF
OUT1
VM
VCC
FIN
GND
RIN
8TH SWITCHED
CAPACITOR
FILTER
1 2 3 4 5 6 7 8
QUAL
RDATA
VREF
MUX
VDD1
VSS1
VSS3
CMP
43
IC601 BA1450 (MAIN BOARD)
FM BAND WIDTH
FM/AM DET OUT

AM OSC OUT
AM MIX OUT
AM MPX IN
FM MPX IN
VCO STOP
AM RF IN
AM IF IN
AM OSC
AM AGC
V . REG
24 23 22 21 20 19 18 17 16 15 14 13
AM AM AM IF
OSC MIX
VREG SD
AM
AGC
DET 1/2
SW 1/2
PD
FM FM LED VCO
DRIVER DECODER
IF DET
SD COMP
DET
1 2 3 4 5 6 7 8 9 10 11 12
VCC
FM IN
FM SD ADJ
GND
FM DET
TUNED
STEREO
IN REQ MUTE
IF OUT
R OUT
L OUT
AM/FM
IC302 µPC1330H (MAIN BOARD) IC681 M5218AFP (MAIN BOARD)
+
+
–
–
INVERTER
V– V+
1 2 3 4 5 6 7 8
COMPARATER
1 2 3 4 5 6 7 8 9
SW R1 GND SW P1 CONT GND VCC SW P2 GND SW R2
IC651 LC72130 (MAIN BOARD)

AOUT1
AOUT2
XOUT
AMIN
FMIN
AIN2
AIN1
VDD
VSS
PD2
PD1
I02
24 23 22 21 20 19 18 17 16 15 14 13
SWALLOW COUNTER
1/16.1/17 4bits
POWER
REFERENCE ON 1/2
DIVIDER RESET
SWALLOW COUNTER
1/16.1/17 4bits
REFERENCE
DIVIDER
PHASE DETECTOR
CHARGE PUMP
2
C B DATA SHIFT REGISTER C B
I/F LATCH I/F
1 2 3 4 5 6 7 8 9 10 11 12
XIN
B05
CE
D1
CL
D0
B01
B02
B03
B04
I01
IFIN
44
SECTION 8
EXPLODED VIEWS
NOTE:
• -XX, -X mean standardized parts, so they may • Abbreviation
have some differences from the original one. CND : Canadian model MX : Mexican model
• Items marked “*” are not stocked since they AUS : Australian model AR : Argentina model
are seldom required for routine service. Some G : German model
delay should be anticipated when ordering these AED : North European model The components identified by mark 0 or
items. EA : Saudi Arabia model dotted line with mark 0 are critical for safety.
• The mechanical parts with no reference number MY : Malaysia model Replace only with part number specified.
in the exploded views are not supplied. SP : Singapore model Les composants identifiés par une marque
• Hardware (# mark) list and accessories and TH : Thai model 0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
packing materials are given in the last of this TW : Taiwan model
le numéro spécifié.
parts list. KR : Korea model
8-1. MAIN SECTION
#3
8
6 #3
#3
#3
2
10
#3
#3 4 CD mechanism deck
12
1
*1 11 *2
7 9
3
#3
M961 5
#3
2
#3
#3
Front panel section 1

#5 #5
Chassis section
*1: US, CND, AEP, AED, CIS, UK, G models
*2: E, EA, AR, AUS, KR, MX, MY, SP, TH, TW models
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
1 3-363-099-01 SCREW(CASE 3 TP2) 8 4-224-547-01 PANEL, BACK (AED,AEP,G,UK)
2 3-363-099-41 SCREW(CASE 3 TP2) 8 4-224-547-11 PANEL, BACK (AR,E,EA,MY,SP,TW)
3 4-224-549-01 CASE(SIDE-L) 8 4-224-547-21 PANEL, BACK (CND,US)
4 X-4952-392-1 PANELASSY, LOADING (CIS) 8 4-224-547-41 PANEL, BACK (AUS,KR,MX,TH)
4 X-4952-393-1 PANELASSY, LOADING (AED,AEP,CND,G,UK,US) 8 4-226-245-01 PANEL, BACK (CIS)
4 X-4952-395-1 PANELASSY, LOADING 9 4-225-252-01 CUSHION (FOOT)

(AR,AUS,E,EA,KR,MX,MY,SP,TH,TW) 10 4-227-984-01 COVER (DUCT)(EXCEPT CIS)
5 4-224-548-01 CASE(SIDE-R) 10 4-227-984-11 COVER (DUCT)(CIS)
6 4-224-550-01 UPPER CASE(TOP) (EXCEPT US,CND) 11 4-951-620-01 SCREW +BVTP (2.6X8)
6 4-224-550-21 UPPER CASE(TOP) (CND,US) 12 1-678-153-11 SENSOR BOARD
7 A-4428-044-A SUB-TRANS BOARD (AED,AEP,CIS,G,UK) (AR,AUS,E,EA,KR,MX,MY,SP,TH,TW)
7 A-4428-058-A SUB-TRANS BOARD (CND,US) M961 1-698-792-11 FAN, DC (AR,AUS,E,EA,KR,MX,MY,SP,TH,TW)
45
8-2. PANEL SECTION
* 67
* For service only (Be sure to refer to "Servicie note" on page 4.)
66
58 67 65
59 61
57 FL601
60 S601
* 67
69
67
*1
62 59
67
68
63
60
64
TAPE mechanism deck
not supplied
51
70
53 55
52
56
54
supplied with S601
*1: E, EA, AR, AUS, KR, MX, MY, SP, TH, TW models
51 X-4952-391-1 LID(L) ASSY, CASSETTE 62 4-224-559-01 CAM(R), HEART
52 X-4952-392-1 LID(R) ASSY, CASSETTE 63 4-224-561-01 BRACKET (HEART CAM R)
53 4-224-554-01 KNOB(VOLUME) 64 4-224-801-01 SPRING (B), TORSION
54 4-225-531-01 BRACKET (RING) 65 4-224-584-01 HOLDER (FL)
55 4-224-800-01 SPRING (JOG), TORSION 66 A-4428-055-A PANEL BOARD,COMPLETE
(AED,AEP,CIS,CND,G,UK,US)
56 4-224-556-01 RING(VOL)
57 X-4952-388-1 PANEL ASSY, FRONT (AED,AEP,G,UK) 66 A-4428-066-A PANEL BOARD,COMPLETE
57 X-4952-389-1 PANEL ASSY, FRONT (AR,AUS,E,EA,KR,MX,MY,SP,TW)
(AR,AUS,E,EA,KR,MX,MY,SP,TH,TW) 66 A-4428-593-A PANEL BOARD,COMPLETE (TH)
57 X-4952-433-1 PANEL ASSY, FRONT (CND,US) 67 4-951-620-01 SCREW (2.6X8), +BVTP
57 X-4952-543-1 PANEL ASSY, FRONT (CIS) 68 4-224-578-01 KNOB(MIC)
(AR,AUS,E,EA,KR,MX,MY,SP,TH,TW)
58 4-224-562-01 BRACKET (HEART CAM L) 69 4-224-802-01 SPRING (A), TORSION
59 4-224-803-01 SPRING (PUSH),COMPRESSION COIL
60 4-224-104-11 DAMPER (EXCEPT CIS) 70 4-225-252-01 CUSHION (FOOT)
60 4-224-104-21 DAMPER (CIS) FL601 1-517-928-11 INDICATOR TUBE, FLUORESCENT
61 4-224-560-01 CAM(L), HEART
46
8-3. MAIN BOARD SECTION
108 108
105
#7
T971 AR US, CND
106 #3 #3 108 108

#7
KR AUS
108
not supplied
107 109
#4 104 EA,MY,SP,TW
108
103
CIS,UK
110
CIS,UK,AED,AEP,G
108
not supplied 101
E,MX,TH
#2
102
101 1-773-042-11 WIRE (FLAT TYPE) (17 CORE) 106 3-703-571-11 BUSHING (S) (4516), CORD (E,MX,TH)
102 A-4428-038-A MAIN BOARD,COMPLETE (AED,AEP,CIS,G,UK) * 106 3-703-244-00 BUSHING (2104), CORD (EXCEPT E,MX,TH)
102 A-4428-046-A MAIN BOARD,COMPLETE (CND,US) 107 A-4428-042-A AMP BOARD,COMPLETE (AED,AEP,CIS,G,UK)
102 A-4428-060-A MAIN BOARD,COMPLETE (MY,SP,TW) 107 A-4428-052-A AMP BOARD,COMPLETE (US)
102 A-4428-256-A MAIN BOARD,COMPLETE (AUS) 107 A-4428-064-A AMP BOARD,COMPLETE
(AR,AUS,E,EA,KR,MX,MY,SP,TW)
102 A-4428-258-A MAIN BOARD,COMPLETE (E)
102 A-4428-262-A MAIN BOARD,COMPLETE (KR) 107 A-4428-252-A AMP BOARD,COMPLETE (CND)
102 A-4428-265-A MAIN BOARD,COMPLETE (EA) 107 A-4428-590-A AMP BOARD,COMPLETE (TH)
102 A-4428-598-A MAIN BOARD,COMPLETE (TH) 0 108 1-690-608-11 CORD, POWER (AUS)
102 A-4428-733-A MAIN BOARD,COMPLETE (AR,MX) 0 108 1-769-079-21 CORD, POWER (KR)
0 108 1-777-071-51 CORD, POWER
* 103 4-988-533-01 HOLDER, PWB (AED,AEP,CIS,G,UK,EA,MY,SP,TW)
104 1-791-897-11 WIRE (FLAT TYPE) (19 CORE)
105 A-4428-045-A TRANS BOARD,COMPLETE (AED,AEP,G,UK) 0 108 1-783-820-11 CORD, POWER (CND,US)
105 A-4428-059-A TRANS BOARD,COMPLETE (US) 0 108 1-783-941-21 CORD, POWER (AR)
105 A-4428-069-A TRANS BOARD,COMPLETE 0 108 1-791-901-11 CORD, POWER (E,MX,TH)
(AR,E,EA,MY,SP,TW) 0 109 1-569-008-21 ADAPTOR, CONVERSION 2P(EA,MY,SP,TW)
0 110 1-770-019-11 ADAPTOR, CONVERSION PLUG 3P (CIS,UK)
105 A-4428-254-A TRANS BOARD,COMPLETE (CND)
105 A-4428-255-A TRANS BOARD,COMPLETE (AUS) 0 T971 1-435-205-11 TRANSFORMER, POWER (US)
105 A-4428-261-A TRANS BOARD,COMPLETE (KR) 0 T971 1-435-206-11 TRANSFORMER, POWER (CND)
105 A-4428-264-A TRANS BOARD,COMPLETE (MX) 0 T971 1-435-207-11 TRANSFORMER, POWER (AED,AEP,CIS,G,UK)
105 A-4428-597-A TRANS BOARD,COMPLETE (TH) 0 T971 1-435-208-11 TRANSFORMER, POWER
105 A-4488-045-A TRANS BOARD,COMPLETE (CIS)

47
Ver 1.1 2001.11
8-4. TAPE MECHANISM DECK SECTION
Note: Two different types of tape mechanism are used depending on models. 165
They maintain compatibility as an entire mechanism even though
160
there are some different parts are used. 159
164
158
161
157
163 167
155 156
159
166
158
151
162
#1
152 151 162

153
#1
152 #1
154
151 X-3374-156-1 PINCH LEVER (REV) ASSY 160 4-227-239-01 BELT (CAPSTAN C)
152 X-3374-155-1 PINCH LEVER (FWD) ASSY 161 X-3378-241-1 MOTOR ASSY
153 1-676-220-11 HEAD (A) BOARD 162 3-019-208-01 WASHER, STOPPER
154 1-676-221-11 HEAD (B) BOARD 163 3-016-533-01 WASHER (FR), STOPPER
155 A-2004-737-A MAIN CHASIS ASSY 164 X-3378-041-1 FLYWHEEL (A-REV) ASSY
156 3-040-580-01 PULLEY (TENSION)
165 X-3378-040-1 FLYWHEEL (A-FWD) ASSY
157 A-2007-838-A LEAF SW BOARD, COMPLETE 166 X-3378-043-1 FLYWHEEL (B-REV) ASSY
158 3-041-947-01 BELT (FR) 167 X-3378-042-1 FLYWHEEL (B-FWD) ASSY
159 3-041-946-01 BELT (CAPSTAN B)
48
Ver 1.1 2001.11
8-5. CD MECHANISM DECK SECTION
201
213 221
206
214
212
211
208 209
208
215
207 208
205
204
216
210
217
218
223
203
220
219 220
202 221
219
219
221
201 222
220
BU-K2BD38
219 221
201 4-933-134-11 SCREW (+PTPWH M2.6X8) 213 4-221-681-01 LEVER (EX)
202 4-221-679-01 CAM(RELAY) 214 4-221-682-01 LEVER (LIFTER)
203 4-221-675-01 TABLE 215 4-221-688-01 PULLEY (B), CHUCKING
204 4-221-686-01 LEVER (CHANGE) 216 1-471-035-11 MAGNET ASSY
205 4-221-676-01 TRAY 217 X-4952-019-1 PULLEY (A) ASSY, CHUCKING
206 4-933-134-51 SCREW (+PTPWH 2.6X8) 218 X-4951-889-1 HOLDER (BU) ASSY
207 1-675-910-11 MOTOR BOARD 219 4-227-549-01 INSULATOR
208 4-951-620-01 SCREW (2.6X8), +BVTP 220 4-227-045-11 SPRING (INSULATOR), COIL
209 1-791-983-12 WIRE (FLAT TYPE) (8 CORE) 221 4-985-672-01 SCREW (+PTPWH M2.6), FLOATING
210 1-675-911-11 ADDRESS SENSOR BOARD 0 222 8-820-116-01 OPTICAL PICK-UP BLOCK (KSM-213DAP)
211 1-675-912-11 DRIVER BOARD 223 4-221-674-03 CHASSIS

212 X-4952-608-1 CAM(U/D) ASSY
49
AMP SECTION 9
ADDRESS SENSOR ELECTRICAL PARTS LIST
NOTE:
• Due to standardization, replacements in the • COILS MX : Mexican model
parts list may be different from the parts uH: µH AR : Argentina model
specified in the diagrams or the components • SEMICONDUCTORS
used on the set. In each case, u: µ, for example: When indicating parts by reference number,
• -XX, -X mean standardized parts, so they uA...: µA... , uPA... , µPA... , please include the board name.
may have some difference from the original uPB... , µPB... , uPC... , µPC... , The components identified by mark 0 or
one. uPD..., µPD... dotted line with mark 0 are critical for safety.
• Items marked “*” are not stocked since they • Abbreviation Replace only with part number specified.
are seldom required for routine service. CND : Canadian model Les composants identifiés par une marque
Some delay should be anticipated when AUS : Australian model 0 sont critiques pour la sécurité.
ordering these items. G : German model Ne les remplacer que par une pièce portant
• CAPACITORS: AED : North European model le numéro spécifié.
uF: µF EA : Saudi Arabia model
• RESISTORS MY : Malaysia model
All resistors are in ohms. SP : Singapore model
METAL: metal-film resistor TH : Thai model
METAL OXIDE: Metal Oxide-film resistor TW : Taiwan model
F: nonflammable KR : Korea model
1-675-911-11 ADDRESS SENSOR BOARD C511 1-162-306-11 CERAMIC 0.01uF
30.00% 16V
********************** C512 1-162-294-31 CERAMIC 0.001uF
10% 50V
(AED,AEP,CIS,G,UK)
< IC > C513 1-162-294-31 CERAMIC 0.001uF 10% 50V
(AED,AEP,CIS,G,UK)
IC711 8-749-016-76 IC RPI-321 C541 1-136-165-00 MYLAR 0.1uF 5.00% 50V
(AED,AEP,CIS,CND,G,UK)
< RESISTOR > C541 1-130-777-00 MYLAR 0.1uF 10.00% 100V
(US,AR,AUS,E,EA,KR,MX,MY,SP,TH,TW)
R711 1-247-876-11 CARBON 75K 5% 1/4W
R712 1-249-409-11 CARBON 220 5% 1/4W F C542 1-135-515-11 ELECT 3300uF 20% 50V
R713 1-249-429-11 CARBON 10K 5% 1/4W (AED,AEP,CIS,CND,G,UK)
C542 1-135-516-11 ELECT 3300uF 20% 63V
< SWITCH > (AR,AUS,E,EA,KR,MX,MY,SP,TH,TW,US)
C543 1-164-159-11 CERAMIC 0.1uF 50V
S711 1-771-821-11 SWITCH, PUSH (1 KEY)(UP DOWN) C545 1-128-549-11 ELECT 3300uF 20.00% 35V
************************************************************** C551 1-126-964-11 ELECT 10uF 20.00% 50V
(EXCEPT US,CND)
A-4428-042-A AMP BOARD, COMPLETE (AED,AEP,G,UK,CIS)
******************** C551 1-128-582-11 ELECT 10uF 20.00% 100V
A-4428-052-A AMP BOARD, COMPLETE (US) (US,CND)
******************** C552 1-162-290-31 CERAMIC 470PF 10% 50V
A-4428-064-A AMP BOARD, COMPLETE C553 1-162-282-31 CERAMIC 100PF 10% 50V
(AR,AUS,E,EA,KR,MX,MY,SP,TW) C554 1-128-551-11 ELECT 22uF 20.00% 25V
******************** (EXCEPT US,CND)
A-4428-252-A AMP BOARD, COMPLETE (CND) C554 1-126-965-11 ELECT 22uF 20.00% 50V
******************** (US,CND)
A-4428-590-A AMP BOARD, COMPLETE (TH)
******************** C557 1-136-495-11 MYLAR 0.068uF 5.00% 50V
C558 1-136-495-11 MYLAR 0.068uF 5.00% 50V
< CAPACITOR > C559 1-126-965-11 ELECT 22uF 20.00% 50V
C501 1-126-964-11 ELECT 10uF 20.00% 50V C559 1-128-560-11 ELECT 22uF 20.00% 100V
(EXCEPT US,CND) (US,AR,AUS,E,EA,KR,MX,MY,SP,TH,TW)
C501 1-128-582-11 ELECT 10uF 20.00% 100V C591 1-136-165-00 MYLAR 0.1uF 5.00% 50V
(US,CND) (AED,AEP,CIS,CND,G,UK)
C502 1-162-290-31 CERAMIC 470PF 10% 50V
C503 1-162-282-31 CERAMIC 100PF 10% 50V C591 1-130-777-00 MYLAR 0.1uF 10.00% 100V
C504 1-128-551-11 ELECT 22uF 20.00% 25V (US,AR,AUS,E,EA,KR,MX,MY,SP,TH,TW)
(EXCEPT US,CND) C592 1-135-515-11 ELECT 3300uF 20% 50V
C504 1-126-965-11 ELECT 22uF20.00% 50V C592 1-135-516-11 ELECT 3300uF 20% 63V
(US,CND) (AR,AUS,E,EA,KR,MX,MY,SP,TH,TW,US)
C507 1-136-495-11 MYLAR 0.068uF 5.00% 50V
C508 1-136-495-11 MYLAR 0.068uF 5.00% 50V < CONNECTOR >
C509 1-126-965-11 ELECT 22uF 20.00% 50V
(AED,AEP,CIS,CND,G,UK) CN502 1-778-981-21 CONNECTOR, BOARD TO BOARD 13P
C509 1-128-560-11 ELECT 22uF 20.00% 100V CN503 1-778-981-21 CONNECTOR, BOARD TO BOARD 13P
(US,AR,AUS,E,EA,KR,MX,MY,SP,TH,TW) CN504 1-785-314-11 PIN, CONNECTOR (STRAIGHT) 2P
50
AMP BD
< DIODE > R515 1-249-433-11 CARBON 22K 5% 1/4W
R516 1-249-429-11 CARBON 10K 5% 1/4W
D501 8-719-911-19 DIODE 1SS133T-72 R517 1-249-421-11 CARBON 2.2K 5% 1/4W F
D502 8-719-911-19 DIODE 1SS133T-72 R518 1-249-429-11 CARBON 10K 5% 1/4W
D541 8-719-028-23 DIODE D3SBA20-4101 R520 1-249-441-11 CARBON 100K 5% 1/4W
(AED,AEP,CIS,CND,G,UK) (AR,AUS,E,EA,KR,MX,MY,SP,TH,TW)
D541 8-719-510-68 DIODE D5SBA204101
(US,AR,AUS,E,EA,KR,MX,MY,SP,TH,TW) R521 1-249-441-11 CARBON 100K 5% 1/4W
D542 8-719-024-99 DIODE 11ES2-NTA2B (AR,AUS,E,EA,KR,MX,MY,SP,TH,TW)
R522 1-249-441-11 CARBON 100K 5% 1/4W
D543 8-719-024-99 DIODE 11ES2-NTA2B (AR,AUS,E,EA,KR,MX,MY,SP,TH,TW)
D551 8-719-911-19 DIODE 1SS133T-72 R523 1-249-409-11 CARBON 220 5% 1/4W
F(AR,AUS,E,EA,KR,MX,MY,SP,TH,TW)
< EARTH > R524 1-247-897-11 CARBON 560K 5% 1/4W
* EP501 1-537-738-21 TERMINAL, EARTH (AED,AEP,CIS,G,UK) R525 1-249-437-11 CARBON 47K 5% 1/4W
* EP502 1-537-738-21 TERMINAL, EARTH (AR,AUS,E,EA,KR,MX,MY,SP,TH,TW)
< IC > R541 1-260-115-11 CARBON 22K 5% 1/2W

R551 1-249-417-11 CARBON 1K 5% 1/4W F
IC501 8-749-016-93 IC STK402-070 (AED,AEP,CIS,CND,G,UK) R552 1-249-438-11 CARBON 56K 5% 1/4W
IC501 8-749-016-94 IC STK402-090 (US) R553 1-249-416-11 CARBON 820 5% 1/4W F
IC501 8-749-016-95 IC STK402-100 (AED,AEP,CIS,CND,G,UK)
(AR,AUS,E,EA,KR,MX,MY,SP,TH,TW) R553 1-249-415-11 CARBON 680 5% 1/4W F
(US)
< TRANSISTOR >
R553 1-249-414-11 CARBON 560 5% 1/4W F
Q501 8-729-140-84 TRANSISTOR 2SC1841TP-PAFAEA (AR,AUS,E,EA,KR,MX,MY,SP,TH,TW)
Q503 8-729-140-82 TRANSISTOR 2SA988TP-PAFAEA R554 1-249-438-11 CARBON 56K 5% 1/4W
Q504 8-729-119-78 TRANSISTOR 2SC2785TP-HFE R555 1-249-417-11 CARBON 1K 5% 1/4W F
(AED,AEP,CIS,CND,G,UK) R556 1-249-431-11 CARBON 15K 5% 1/4W
Q504 8-729-140-84 TRANSISTOR 2SC1841TP-PAFAEA R557 1-249-441-11 CARBON 100K 5% 1/4W
(US,AR,AUS,E,EA,KR,MX,MY,SP,TH,TW)
Q551 8-729-140-84 TRANSISTOR 2SC1841TP-PAFAEA 0 R558 1-217-156-00 METAL 0.22 20% 5W
R559 1-260-076-11 CARBON 10 5% 1/2W
Q581 8-729-140-84 TRANSISTOR 2SC1841TP-PAFAEA 0 R560 1-217-156-00 METAL 0.22 20% 5W
Q582 8-729-119-78 TRANSISTOR 2SC2785TP-HFE 0 R561 1-212-881-11 FUSIBLE 100 5% 1/4W
(AR,AUS,E,EA,KR,MX,MY,SP,TH,TW) R581 1-249-435-11 CARBON 33K 5% 1/4W
Q583 8-729-900-36 TRANSISTOR BA1F4M-TP
Q584 8-729-119-78 TRANSISTOR 2SC2785TP-HFE R591 1-260-115-11 CARBON 22K 5% 1/2W
(AR,AUS,E,EA,KR,MX,MY,SP,TH,TW) **************************************************************
< RESISTOR > A-4724-934-A BD BOARD, COMPLETE

*******************
R501 1-249-417-11 CARBON 1K 5% 1/4W F
R502 1-249-438-11 CARBON 56K 5% 1/4W < CAPACITOR >
R503 1-249-416-11 CARBON 820 5% 1/4W F
(AED,AEP,CIS,CND,G,UK) C101 1-163-005-11 CERAMIC CHIP 470PF 10% 50V
R503 1-249-415-11 CARBON 680 5% 1/4W F C102 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
(US) C103 1-163-005-11 CERAMIC CHIP 470PF 10% 50V
(AR,AUS,E,EA,KR,MX,MY,SP,TH,TW) C108 1-164-004-11 CERAMIC CHIP 0.1uF 10% 25V
R504 1-249-438-11 CARBON 56K 5% 1/4W C109 1-163-011-11 CERAMIC CHIP 0.0015uF 10% 50V
R505 1-249-417-11 CARBON 1K 5% 1/4W F C110 1-164-182-11 CERAMIC CHIP 0.0033uF 10% 50V
R506 1-249-431-11 CARBON 15K 5% 1/4W C111 1-163-251-11 CERAMIC CHIP 100PF 5.00% 50V
R507 1-249-441-11 CARBON 100K 5% 1/4W C112 1-107-682-11 CERAMIC CHIP 1uF 10.00% 16V
0 R508 1-217-156-00 METAL 0.22 20% 5W C114 1-163-038-91 CERAMIC CHIP 0.1uF 25V
R509 1-260-076-11 CARBON 10 5% 1/2W C115 1-104-665-11 ELECT 100uF 20.00% 10V
0 R510 1-217-156-00 METAL 0.22 20% 5W C116 1-104-665-11 ELECT 100uF 20.00% 10V
0 R511 1-212-881-11 FUSIBLE 100 5% 1/4W C117 1-104-665-11 ELECT 100uF 20.00% 10V
0 R512 1-202-972-61 FUSIBLE 1 5% 1/4W C118 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
R514 1-249-421-11 CARBON 2.2K 5% 1/4W F C119 1-163-235-11 CERAMIC CHIP 22PF 5.00% 50V

51
BD DRIVER
C121 1-163-038-91 CERAMIC CHIP 0.1uF 25V R111 1-216-121-91 RES-CHIP 1M 5% 1/10W
C122 1-104-665-11 ELECT 100uF 20.00% 10V R113 1-216-121-91 RES-CHIP 1M 5% 1/10W
C123 1-163-021-91 CERAMIC CHIP 0.01uF 10.00% 50V R114 1-216-073-00 METAL CHIP 10K 5% 1/10W
C124 1-107-823-11 CERAMIC CHIP 0.47uF 10.00% 16V R116 1-216-001-00 METAL CHIP 10 5% 1/10W
C125 1-163-038-91 CERAMIC CHIP 0.1uF 25V R117 1-216-049-91 RES-CHIP 1K 5% 1/10W
C126 1-163-038-91 CERAMIC CHIP 0.1uF 25V R118 1-216-025-91 RES-CHIP 100 5% 1/10W
C127 1-104-665-11 ELECT 100uF 20.00% 10V R119 1-216-059-00 METAL CHIP 2.7K 5% 1/10W
C129 1-163-031-11 CERAMIC CHIP 0.01uF 50V R123 1-216-073-00 METAL CHIP 10K 5% 1/10W
C130 1-164-346-11 CERAMIC CHIP 1uF 16V R124 1-216-097-91 RES-CHIP 100K 5% 1/10W
C131 1-126-964-11 ELECT 10uF 20.00% 50V R131 1-216-033-00 METAL CHIP 220 5% 1/10W
C133 1-164-346-11 CERAMIC CHIP 1uF 16V R143 1-216-103-00 METAL CHIP 180K 5% 1/10W
C140 1-164-346-11 CERAMIC CHIP 1uF 16V R144 1-216-103-00 METAL CHIP 180K 5% 1/10W
C141 1-164-346-11 CERAMIC CHIP 1uF 16V R147 1-216-069-00 METAL CHIP 6.8K 5% 1/10W
C143 1-163-038-91 CERAMIC CHIP 0.1uF 25V R148 1-216-001-00 METAL CHIP 10 5% 1/10W
C145 1-163-038-91 CERAMIC CHIP 0.1uF 25V R149 1-216-001-00 METAL CHIP 10 5% 1/10W
C159 1-163-019-00 CERAMIC CHIP 0.0068uF 10% 50V R159 1-216-101-00 METAL CHIP 150K 5% 1/10W
C162 1-104-665-11 ELECT 100uF 20.00% 10V R162 1-216-101-00 METAL CHIP 150K 5% 1/10W
C163 1-104-665-11 ELECT 100uF 20.00% 10V R171 1-216-078-00 RES-CHIP 16K 5% 1/10W
C167 1-163-237-11 CERAMIC CHIP 27PF 5.00% 50V R173 1-216-077-91 RES-CHIP 15K 5% 1/10W
C168 1-163-235-11 CERAMIC CHIP 22PF 5.00% 50V R181 1-216-078-00 RES-CHIP 16K 5% 1/10W
C171 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V R182 1-216-073-00 METAL CHIP 10K 5% 1/10W
C172 1-163-123-00 CERAMIC CHIP 180PF 5% 50V R183 1-216-077-91 RES-CHIP 15K 5% 1/10W
C181 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
< NETWORK >
C182 1-163-123-00 CERAMIC CHIP 180PF 5% 50V
RN101 1-233-576-11 RES, CHIP NETWORK 100
< CONNECTOR >
< SWITCH >
CN101 1-784-741-11 CONNECTOR, FFC 19P
CN102 1-793-907-11 CONNECTOR, FFC/FPC 16P S101 1-771-853-11 SWITCH, DETECTION (LIMIT IN)
< FERRITE BEAD > < VIBRATOR >
FB101 1-500-445-21 FERRITE 0UH X101 1-579-280-11 VIBRATOR, CRYSTAL(16.9344 MHz )

FB103 1-500-445-21 FERRITE 0UH **************************************************************
< IC > 1-675-912-11 DRIVER BOARD

*************
IC101 8-752-386-85 IC CXD2587Q
IC102 8-759-549-28 IC BA5974FP-E2 < CAPACITOR >
IC103 8-752-085-51 IC CXA2568M-T6
C702 1-126-964-51 ELECT 10uF 20.00% 50V
< TRANSISTOR >
< CONNECTOR >
Q101 8-729-049-31 TRANSISTOR 2SB710-RTX
CN701 1-785-336-11 PIN, CONNECTOR(LIGHT ANGLE)10P
< RESISTOR > CN702 1-785-550-11 CONNECTOR, FFC/FPC 8P
R101 1-216-077-91 RES-CHIP 15K 5% 1/10W < DIODE >

R102 1-216-097-91 RES-CHIP 100K 5% 1/10W
R103 1-216-077-91 RES-CHIP 15K 5% 1/10W D701 8-719-983-63 DIODE MTZJ-T-72-3.3B
R104 1-216-085-00 METAL CHIP 33K 5% 1/10W
R105 1-216-073-00 METAL CHIP 10K 5% 1/10W < IC >
R106 1-216-049-91 RES-CHIP 1K 5% 1/10W IC701 8-759-598-69 IC BA6956AN

R107 1-216-073-00 METAL CHIP 10K 5% 1/10W
R108 1-216-061-00 METAL CHIP 3.3K 5% 1/10W < RESISTOR >
R109 1-216-121-91 RES-CHIP 1M 5% 1/10W
R110 1-216-025-91 RES-CHIP 100 5% 1/10W R701 1-249-411-11 CARBON 330 5% 1/4W
R702 1-249-401-11 CARBON 47 5% 1/4W F
**************************************************************
52
HEAD (A) HEAD (B) LEAF SW MAIN
1-676-220-11 HEAD (A) BOARD A-4428-038-A MAIN BOARD, COMPLETE (AED,AEP,G,UK,CIS)
************** *********************
A-4428-046-A MAIN BOARD, COMPLETE (US,CND)
< CONNECTOR > *********************
A-4428-060-A MAIN BOARD, COMPLETE (MY,SP,TW)
* CN1 1-564-719-11 PIN, CONNECTOR (SMALL TYPE) 3P *********************
************************************************************** A-4428-256-A MAIN BOARD, COMPLETE (AUS)
*********************
1-676-221-11 HEAD (B) BOARD A-4428-258-A MAIN BOARD, COMPLETE (E)
************** *********************
A-4428-262-A MAIN BOARD, COMPLETE (KR)
CN2 1-564-722-11 PIN, CONNECTOR (SMALL TYPE) 6P *********************
************************************************************** A-4428-265-A MAIN BOARD, COMPLETE (EA)
*********************
A-2007-838-A LEAF SW BOARD, COMPLETE A-4428-598-A MAIN BOARD, COMPLETE (TH)
*********************** *********************
A-4428-733-A MAIN BOARD, COMPLETE (AR,MX)
< CAPACITOR > *********************
C1001 1-107-716-11 ELECT 33uF 20.00% 10V 4-224-796-21 HEAT SINK (B)
7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S
< CONNECTOR >
< CAPACITOR >
CN1001 1-568-860-21 SOCKET, CONNECTOR 17P
< DIODE > C102 1-126-961-11 ELECT 2.2uF 20.00% 50V
C103 1-126-964-11 ELECT 10uF 20.00% 50V
D1001 8-719-911-19 DIODE 1SS133T-72 C104 1-126-964-11 ELECT 10uF 20.00% 50V
D1002 8-719-911-19 DIODE 1SS133T-72 C105 1-126-964-11 ELECT 10uF 20.00% 50V
< IC > C107 1-136-167-00 MYLAR 0.15uF 5.00% 50V

(US,CND)
IC1001 8-749-016-76 IC RPI-321 C107 1-136-164-00 MYLAR 0.082uF 5.00% 50V
IC1002 8-749-016-76 IC RPI-321 (EXCEPT US,CND)
C108 1-136-167-00 MYLAR 0.15uF 5.00% 50V
< TRANSISTOR > (US,CND)
C108 1-136-164-00 MYLAR 0.082uF 5.00% 50V
Q1001 8-729-029-56 TRANSISTOR DTA144ESA-TP (EXCEPT US,CND)
< RESISTOR >
R1002 1-249-409-11 CARBON 220 5% 1/4W F C112 1-126-961-11 ELECT 2.2uF 20.00% 50V
R1003 1-249-414-11 CARBON 560 5% 1/4W F C113 1-126-957-11 ELECT 0.22uF 20.00% 50V
R1004 1-247-834-11 CARBON 1.3K 5% 1/4W (AR,AUS,E,EA,KR,MX,MY,SP,TW)
R1005 1-247-818-11 CARBON 300 5% 1/4W C115 1-136-165-00 MYLAR 0.1uF 5.00% 50V
R1006 1-247-864-11 CARBON 24K 5% 1/4W C116 1-136-165-00 MYLAR 0.1uF 5.00% 50V
R1007 1-247-780-00 CARBON 7.5 5% 1/4W C117 1-126-964-11 ELECT 10uF 20.00% 50V
R1008 1-249-417-11 CARBON 1K 5% 1/4W F C118 1-126-961-11 ELECT 2.2uF 20.00% 50V
(EXCEPT US,CND)
< VARIABLE RESISTOR > C121 1-126-964-11 ELECT 10uF 20.00% 50V
RV1001 1-241-785-11 RES, ADJ, CARBON 10K C122 1-126-964-11 ELECT 10uF 20.00% 50V
RV1002 1-241-785-11 RES, ADJ, CARBON 10K (AR,AUS,E,EA,KR,MX,MY,SP,TW)
< SWITCH > C123 1-126-964-11 ELECT 10uF 20.00% 50V

S1001 1-570-953-11 SWITCH, PUSH (1 KEY)(A PLAY) C124 1-163-038-91 CERAMIC CHIP 0.1uF 25V
S1002 1-570-953-11 SWITCH, PUSH (1 KEY)(B PLAY) (EXCEPT US,CND)
S1003 1-771-333-11 SWITCH, LEAF (A HALF) C125 1-126-964-11 ELECT 10uF 20.00% 50V
S1004 1-771-536-11 SWITCH, LEAF (A 120/70) (AR,AUS,E,EA,KR,MX,MY,SP,TW)
S1005 1-771-536-11 SWITCH, LEAF (REC A) C131 1-136-169-00 MYLAR 0.22uF 5.00% 50V
C132 1-126-964-11 ELECT 10uF 20.00% 50V
S1006 1-771-333-11 SWITCH, LEAF (B HALF)
S1008 1-771-536-11 SWITCH, LEAF (B 120/70) C133 1-126-924-11 ELECT 330uF 20.00% 6.3V
S1009 1-771-536-11 SWITCH, LEAF (REC B) C134 1-163-038-91 CERAMIC CHIP 0.1uF 25V
************************************************************** C135 1-126-964-11 ELECT 10uF 20.00% 50V
C141 1-126-964-11 ELECT 10uF 20.00% 50V
53
MAIN
C142 1-163-038-91 CERAMIC CHIP 0.1uF 25V C317 1-126-933-11 ELECT 100uF 20.00% 16V
C144 1-126-934-11 ELECT 220uF 20.00% 10V C319 1-126-961-11 ELECT 2.2uF 20.00% 50V
C151 1-163-001-11 CERAMIC CHIP 220PF 10% 50V C320 1-126-961-11 ELECT 2.2uF 20.00% 50V
C152 1-126-961-11 ELECT 2.2uF 20.00% 50V C321 1-163-131-00 CERAMIC CHIP 390PF 5% 50V
C153 1-126-964-11 ELECT 10uF 20.00% 50V C322 1-163-117-00 CERAMIC CHIP 100PF 5% 50V
C154 1-126-964-11 ELECT 10uF 20.00% 50V C323 1-130-487-00 MYLAR 0.022uF 5% 50V
C157 1-136-167-00 MYLAR 0.15uF 5.00% 50V C325 1-126-965-11 ELECT 22uF 20.00% 50V
(US,CND) C326 1-163-131-00 CERAMIC CHIP 390PF 5% 50V
C157 1-136-164-00 MYLAR 0.082uF 5.00% 50V
(EXCEPT US,CND) C327 1-126-933-11 ELECT 100uF 20.00% 16V
C158 1-136-167-00 MYLAR 0.15uF 5.00% 50V C329 1-130-483-00 MYLAR 0.01uF 5% 50V
(US,CND) C330 1-126-964-11 ELECT 10uF 20.00% 50V
(EXCEPT US,CND)
C159 1-163-019-00 CERAMIC CHIP 0.0068uF 10% 50V C332 1-137-427-11 MYLAR 120PF 5.00% 50V
C160 1-163-019-00 CERAMIC CHIP 0.0068uF 10% 50V C333 1-163-003-11 CERAMIC CHIP 330PF 10% 50V
C161 1-163-018-00 CERAMIC CHIP 0.0056uF 5% 50V C334 1-163-103-00 CERAMIC CHIP 27PF 5% 50V
C335 1-137-393-11 MYLAR 0.01uF 5.00% 100V
C162 1-126-961-11 ELECT 2.2uF 20.00% 50V C336 1-126-961-11 ELECT 2.2uF 20.00% 50V
C165 1-136-165-00 MYLAR 0.1uF 5.00% 50V
C166 1-136-165-00 MYLAR 0.1uF 5.00% 50V C337 1-130-485-00 MYLAR 0.015uF 5% 50V
(AR,AUS,E,EA,KR,MX,MY,SP,TW) C340 1-130-486-00 MYLAR 0.018uF 10% 50V
C341 1-126-960-11 ELECT 1uF 20.00% 50V
C172 1-126-964-11 ELECT 10uF 20.00% 50V
(AR,AUS,E,EA,KR,MX,MY,SP,TW) C342 1-104-664-11 ELECT 47uF 20.00% 16V
(AR,AUS,E,EA,KR,MX,MY,SP,TW) C352 1-130-479-00 MYLAR 0.0047uF 5% 50V
C199 1-163-038-91 CERAMIC CHIP 0.1uF 25V C353 1-136-165-00 MYLAR 0.1uF 5.00% 50V
C202 1-126-935-11 ELECT 470uF 20.00% 16V
C356 1-126-960-11 ELECT 1uF 20.00% 50V
C203 1-163-117-00 CERAMIC CHIP 100PF 5% 50V C357 1-126-960-11 ELECT 1uF 20.00% 50V
C204 1-126-961-11 ELECT 2.2uF 20.00% 50V C358 1-126-964-11 ELECT 10uF 20.00% 50V
C205 1-163-117-00 CERAMIC CHIP 100PF 5% 50V C359 1-137-194-81 MYLAR 0.47uF 5.00% 50V
C207 1-126-916-11 ELECT 1000uF 20.00% 6.3V
C208 1-163-117-00 CERAMIC CHIP 100PF 5% 50V C363 1-163-017-00 CERAMIC CHIP 0.0047uF 5% 50V
C213 1-163-181-00 CERAMIC CHIP 100PF 5.00% 50V C369 1-126-961-11 ELECT 2.2uF 20.00% 50V
(AED,AEP,CIS,CND,G,UK,US) C370 1-126-961-11 ELECT 2.2uF 20.00% 50V
(AED,AEP,CIS,CND,G,UK,US) C371 1-163-131-00 CERAMIC CHIP 390PF 5% 50V
C215 1-163-117-00 CERAMIC CHIP 100PF 5% 50V C372 1-163-117-00 CERAMIC CHIP 100PF 5% 50V
(AED,AEP,CIS,CND,G,UK,US) C373 1-130-487-00 MYLAR 0.022uF 5% 50V
C374 1-126-964-11 ELECT 10uF 20.00% 50V
C302 1-130-479-00 MYLAR 0.0047uF 5% 50V
C303 1-136-165-00 MYLAR 0.1uF 5.00% 50V C376 1-163-131-00 CERAMIC CHIP 390PF 5% 50V
C379 1-130-483-00 MYLAR 0.01uF 5% 50V
C308 1-126-964-11 ELECT 10uF 20.00% 50V
C310 1-163-005-11 CERAMIC CHIP 470PF 10% 50V C382 1-137-427-11 MYLAR 120PF 5.00% 50V
C312 1-126-959-11 ELECT 0.47uF 20.00% 50V C390 1-126-964-11 ELECT 10uF 20.00% 50V
C314 1-126-964-11 ELECT 10uF 20.00% 50V
C315 1-126-963-11 ELECT 4.7uF 20.00% 50V
C316 1-126-933-11 ELECT 100uF 20.00% 16V
54
MAIN
C410 1-163-233-11 CERAMIC CHIP 18PF 5.00% 50V C637 1-163-021-91 CERAMIC CHIP 0.01uF 10.00% 50V
C411 1-163-231-11 CERAMIC CHIP 15PF 5.00% 50V C638 1-163-135-00 CERAMIC CHIP 560PF 5% 50V
C414 1-163-038-91 CERAMIC CHIP 0.1uF 25V (AED,AEP,CIS,G,UK)
C416 1-126-916-11 ELECT 1000uF 20.00% 6.3V C641 1-163-031-11 CERAMIC CHIP 0.01uF 50V
C462 1-126-933-11 ELECT 100uF 20.00% 16V C644 1-163-087-00 CERAMIC CHIP 4PF 50V
C645 1-163-031-11 CERAMIC CHIP 0.01uF 50V
C501 1-136-165-00 MYLAR 0.1uF 5.00% 50V C651 1-163-239-11 CERAMIC CHIP 33PF 5.00% 50V
C502 1-136-165-00 MYLAR 0.1uF 5.00% 50V C652 1-163-235-11 CERAMIC CHIP 22PF 5.00% 50V
C503 1-126-964-11 ELECT 10uF 20.00% 50V C655 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
C504 1-109-953-11 ELECT 2.2uF 20.00% 50V
C505 1-163-038-91 CERAMIC CHIP 0.1uF 25V C656 1-163-031-11 CERAMIC CHIP 0.01uF 50V
C601 1-163-031-11 CERAMIC CHIP 0.01uF 50V C658 1-126-961-11 ELECT 2.2uF 20.00% 50V
C603 1-104-664-11 ELECT 47uF 20.00% 16V
C604 1-163-031-11 CERAMIC CHIP 0.01uF 50V C661 1-163-031-11 CERAMIC CHIP 0.01uF 50V
C607 1-216-295-91 SHORT 0 C663 1-163-031-11 CERAMIC CHIP 0.01uF 50V
(AR,AUS,E,EA,KR,MX,MY,SP,TH,TW) C669 1-163-031-11 CERAMIC CHIP 0.01uF 50V
C681 1-126-964-11 ELECT 10uF 20.00% 50V
C613 1-126-960-11 ELECT 1uF 20.00% 50V C683 1-163-038-91 CERAMIC CHIP 0.1uF 25V
C684 1-104-664-11 ELECT 47uF 20.00% 16V
C616 1-163-021-91 CERAMIC CHIP 0.01uF 10.00% 50V C685 1-126-964-11 ELECT 10uF 20.00% 50V
(AR,AUS,E,EA,KR,MX,MY,SP,TH,TW) (AED,AEP,CIS,G,UK)
C616 1-163-023-00 CERAMIC CHIP 0.015uF 5% 50V C686 1-126-961-11 ELECT 2.2uF 20.00% 50V
(AED,AEP,CIS,CND,G,UK,US) (AED,AEP,CIS,G,UK)
C617 1-163-021-91 CERAMIC CHIP 0.01uF 10.00% 50V
(AR,AUS,E,EA,KR,MX,MY,SP,TH,TW) C687 1-163-129-00 CERAMIC CHIP 330PF 5% 50V
C617 1-163-023-00 CERAMIC CHIP 0.015uF 5% 50V (AED,AEP,CIS,G,UK)
(AED,AEP,CIS,CND,G,UK,US) C688 1-163-031-11 CERAMIC CHIP 0.01uF 50V
(AED,AEP,CIS,G,UK)
C620 1-126-962-11 ELECT 3.3uF 20.00% 50V C690 1-126-961-11 ELECT 2.2uF 20.00% 50V
C621 1-126-962-11 ELECT 3.3uF 20.00% 50V (AED,AEP,CIS,G,UK)
(AED,AEP,CIS,G,UK)
C623 1-126-964-11 ELECT 10uF 20.00% 50V
C624 1-126-960-11 ELECT 1uF 20.00% 50V C692 1-163-245-11 CERAMIC CHIP 56PF 5.00% 50V
C625 1-163-125-00 CERAMIC CHIP 220PF 5% 50V (AED,AEP,CIS,G,UK)
(US,CND,AR,AUS,E,EA,KR,MX,MY,SP,TH,TW) C693 1-163-245-11 CERAMIC CHIP 56PF 5.00% 50V
(AED,AEP,CIS,G,UK) C694 1-163-031-11 CERAMIC CHIP 0.01uF 50V
C626 1-104-760-11 CERAMIC CHIP 0.047uF 10.00% 50V (AED,AEP,CIS,G,UK)
(US,CND,AR,AUS,E,EA,KR,MX,MY,SP,TH,TW) C801 1-163-038-91 CERAMIC CHIP 0.1uF 25V
(AED,AEP,CIS,G,UK)
C630 1-126-964-11 ELECT 10uF 20.00% 50V (AED,AEP,CIS,G,UK)
C631 1-163-031-11 CERAMIC CHIP 0.01uF 50V C803 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V
C821 1-126-933-11 ELECT 100uF 20.00% 16V
C632 1-126-933-11 ELECT 100uF 20.00% 16V C822 1-126-961-11 ELECT 2.2uF 20.00% 50V
C636 1-163-021-91 CERAMIC CHIP 0.01uF 10.00% 50V
55
MAIN
C841 1-126-959-11 ELECT 0.47uF 20.00% 50V D601 8-719-056-83 DIODE UDZ-TE-17-6.8B
(EXCEPT US,CND) D641 8-719-914-42 DIODE DA204K-T-146
C851 1-163-038-91 CERAMIC CHIP 0.1uF 25V D651 8-719-988-61 DIODE 1SS355TE-17
(AED,AEP,CIS,G,UK) D681 8-719-988-61 DIODE 1SS355TE-17 (AED,AEP,CIS,G,UK)
C852 1-163-038-91 CERAMIC CHIP 0.1uF 25V D801 8-719-988-61 DIODE 1SS355TE-17
(AED,AEP,CIS,G,UK)
C853 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V D822 8-719-988-61 DIODE 1SS355TE-17
C861 1-107-717-11 ELECT 47uF 20.00% 50V D841 8-719-988-61 DIODE 1SS355TE-17 (EXCEPT US,CND)
D861 8-719-988-61 DIODE 1SS355TE-17
C862 1-107-721-11 ELECT 4.7uF 20.00% 100V D901 8-719-200-82 DIODE 11ES2-TB5
C863 1-107-721-11 ELECT 4.7uF 20.00% 100V D902 8-719-200-82 DIODE 11ES2-TB5
C901 1-126-768-11 ELECT 2200uF 20.00% 16V
C902 1-136-165-00 MYLAR 0.1uF 5.00% 50V D903 8-719-200-82 DIODE 11ES2-TB5
D906 8-719-200-82 DIODE 11ES2-TB5
C907 1-126-943-11 ELECT 2200uF 20.00% 25V
C911 1-126-964-11 ELECT 10uF 20.00% 50V D909 8-719-200-82 DIODE 11ES2-TB5
C912 1-126-916-11 ELECT 1000uF 20.00% 6.3V D931 8-719-200-82 DIODE 11ES2-TB5
D932 8-719-200-82 DIODE 11ES2-TB5
C921 1-126-964-11 ELECT 10uF 20.00% 50V D933 8-719-200-82 DIODE 11ES2-TB5
C922 1-126-933-11 ELECT 100uF 20.00% 16V D951 8-719-988-61 DIODE 1SS355TE-17
C932 1-126-935-11 ELECT 470uF 20.00% 16V
D961 8-719-988-61 DIODE 1SS355TE-17
C961 1-163-038-91 CERAMIC CHIP 0.1uF 25V (AR,AUS,E,EA,KR,MX,MY,SP,TH,TW)
C962 1-126-963-11 ELECT 4.7uF 20.00% 50V < FERRITE BEAD >
C971 1-126-964-11 ELECT 10uF 20.00% 50V FB201 1-216-295-91 SHORT 0
C972 1-126-926-11 ELECT 1000uF 20.00% 10V (AR,AUS,E,EA,KR,MX,MY,SP,TW)
FB201 1-550-907-21 FERRITE 0UH
< FILTER > (AED,AEP,CIS,CND,G,UK,US)
FB203 1-216-295-91 SHORT 0
CF601 1-760-023-11 FILTER, CERAMIC (AR,AUS,E,EA,KR,MX,MY,SP,TW)
(US,CND,AR,AUS,E,EA,KR,MX,MY,SP,TH,TW) FB203 1-550-907-21 FERRITE 0UH
CF601 1-579-185-21 FILTER, CERAMIC (AED,AEP,CIS,G,UK) (AED,AEP,CIS,CND,G,UK,US)
CF602 1-760-023-11 FILTER, CERAMIC FB204 1-216-295-91 SHORT 0
(US,CND,AR,AUS,E,EA,KR,MX,MY,SP,TH,TW) (AR,AUS,E,EA,KR,MX,MY,SP,TW)
CF602 1-579-185-21 FILTER, CERAMIC (AED,AEP,CIS,G,UK)
FB204 1-550-907-21 FERRITE 0UH
< CONNECTOR > (AED,AEP,CIS,CND,G,UK,US)
FB416 1-216-295-91 SHORT 0
CN201 1-784-741-11 CONNECTOR, FFC 19P FB462 1-216-295-91 SHORT 0
* CN301 1-568-449-11 HOUSING, CONNECTOR(PC BOARD)3P FB499 1-216-295-91 SHORT 0
CN304 1-784-778-11 CONNECTOR, FFC 17P
CN401 1-793-766-11 CONNECTOR, BOARD TO BOARD 30P < FRONT END >
CN901 1-778-982-21 CONNECTOR, BOARD TO BOARD 13P
FE601 1-693-477-11 FRONT END (3 GANGS)
CN902 1-778-982-21 CONNECTOR, BOARD TO BOARD 13P (AR,AUS,E,EA,KR,MX,MY,SP,TH,TW)
* CN903 1-564-506-11 PLUG, CONNECTOR 3P FE602 1-693-478-11 FRONT END (FM3 GANGS) (US,CND)
(AR,AUS,E,EA,KR,MX,MY,SP,TH,TW) FE603 1-693-496-11 FRONT END (4 GANG)
(AED,AEP,CIS,G,UK)
< DIODE >
< IC >
D501 8-719-988-61 DIODE 1SS355TE-17
D502 8-719-988-61 DIODE 1SS355TE-17 IC101 8-759-652-04 IC M61504FP-TP
D503 8-719-988-61 DIODE 1SS355TE-17 IC102 8-759-099-06 IC M5218AFP-TE1 (EXCEPT US,CND)
D504 8-719-988-61 DIODE 1SS355TE-17 IC104 8-759-099-06 IC M5218AFP-TE1
D505 8-719-988-61 DIODE 1SS355TE-17 (AR,AUS,E,EA,KR,MX,MY,SP,TW)
IC201 8-749-923-04 IC TOTX178A (OPTICAL)
D506 8-719-988-61 DIODE 1SS355TE-17 IC301 8-759-652-80 IC HA12227F
D508 8-719-988-61 DIODE 1SS355TE-17
D509 8-719-988-61 DIODE 1SS355TE-17 IC302 8-759-143-54 IC uPC1330HA
(AED,AEP,CIS,CND,G,UK,US) IC303 8-759-656-83 IC NJM4580MD-TE
D510 8-719-988-61 DIODE 1SS355TE-17 IC304 8-759-656-83 IC NJM4580MD-TE
(AED,AEP,CIS,CND,G,UK,US) IC401 8-759-652-48 IC M30622MAA-A25FP
D511 8-719-988-61 DIODE 1SS355TE-17 IC501 8-759-635-63 IC M51943BSL-TP
56
MAIN
IC601 8-759-652-00 IC BA1450 JR907 1-216-295-91 SHORT 0
IC651 8-759-288-54 IC LC72130 (AED,AEP,CIS,CND,G,UK,US)
IC681 8-759-099-06 IC M5218AFP-TE1 (AED,AEP,CIS,G,UK) JR908 1-216-295-91 SHORT 0
IC682 8-759-541-48 IC BU1924 (AED,AEP,CIS,G,UK) (AED,AEP,CIS,CND,G,UK,US,AR,AUS,E,EA,KR,MX,TH)
IC911 8-759-039-69 IC uPC7805AHF JR909 1-216-295-91 SHORT 0
(AED,AEP,CIS,CND,G,UK,US,AR,AUS,E,EA,KR,MX,TH)
IC921 8-759-088-08 IC uPC7812AHF JR910 1-216-295-91 SHORT 0
IC951 8-759-039-69 IC uPC7805AHF (AED,AEP,CIS,CND,G,UK,US)
IC971 8-759-701-59 IC M5F7809L JR911 1-216-295-91 SHORT 0
< IFT >
JR923 1-216-295-91 SHORT 0
IFT601 1-435-295-11 TRANSFORMER, IF (US,CND,AR,AUS,E,EA,KR,MX,MY,SP,TW)
JR924 1-216-295-91 SHORT 0
< JACK > (US,CND,AR,AUS,E,EA,KR,MX,MY,SP,TW)
J101 1-793-987-11 JACK, PIN 2P (MD/VIDEO) < COIL >
< JUMPER RESISTOR > L201 1-414-189-31 INDUCTOR 100uH

L301 1-410-780-11 INDUCTOR 27MH
JR1 1-216-296-91 SHORT 0 L302 1-414-193-41 INDUCTOR 220uH
JR2 1-216-296-91 SHORT 0 L303 1-414-193-41 INDUCTOR 220uH
JR3 1-216-296-91 SHORT 0 L351 1-410-780-11 INDUCTOR 27MH
JR4 1-216-296-91 SHORT 0
JR6 1-216-295-91 SHORT 0 L641 1-408-765-21 INDUCTOR CHIP 1uH (AED,AEP,CIS,G,UK)
L642 1-216-296-91 SHORT 0
JR7 1-216-296-91 SHORT 0 (US,CND,AR,AUS,E,EA,KR,MX,MY,SP,TH,TW)
JR10 1-216-296-91 SHORT 0 L801 1-420-872-00 COIL, AIR-CORE (AED,AEP,CIS,G,UK)
JR11 1-216-296-91 SHORT 0
L851 1-420-872-00 COIL, AIR-CORE (AED,AEP,CIS,G,UK)
JR12 1-216-296-91 SHORT 0
JR13 1-216-296-91 SHORT 0 < FILTER >
JR14 1-216-296-91 SHORT 0
JR15 1-216-296-91 SHORT 0 LPF601 1-234-458-11 FILTER, LOW PASS
JR16 1-216-295-91 SHORT 0 LPF602 1-234-458-11 FILTER, LOW PASS
JR17 1-216-296-91 SHORT 0 < TRANSISTOR >

JR18 1-216-295-91 SHORT 0
JR19 1-216-296-91 SHORT 0 Q101 8-729-119-78 TRANSISTOR 2SC2785TP-HFE
JR20 1-216-295-91 SHORT 0 (EXCEPT US,CND)
JR21 1-216-295-91 SHORT 0 Q102 8-729-045-44 TRANSISTOR 2SK1132-T
(EXCEPT US,CND)
JR601 1-216-296-91 SHORT 0 (EXCEPT US,CND) Q103 8-729-141-30 TRANSISTOR 2SC3623ATP-LK
JR605 1-216-296-91 SHORT 0
Q152 8-729-045-44 TRANSISTOR 2SK1132-T
JR607 1-216-295-91 SHORT 0 Q153 8-729-141-30 TRANSISTOR 2SC3623ATP-LK
JR608 1-216-296-91 SHORT 0 Q301 8-729-801-93 TRANSISTOR 2SD1387-34-TP
JR609 1-216-295-91 SHORT 0 Q302 8-729-142-46 TRANSISTOR 2SC2001TP-LK
(AR,AUS,E,EA,KR,MX,MY,SP,TH,TW) Q303 8-729-142-46 TRANSISTOR 2SC2001TP-LK
JR611 1-216-296-91 SHORT 0
Q304 8-729-900-63 TRANSISTOR BN1F4M-TP
JR612 1-216-295-91 SHORT 0 (US,CND) Q305 8-729-900-80 TRANSISTOR BA1A4M-TP
JR614 1-216-295-91 SHORT 0 (AED,AEP,CIS,G,UK) Q391 8-729-140-04 TRANSISTOR 2SB1116-TP-LK
JR615 1-216-295-91 SHORT 0 Q392 8-729-900-80 TRANSISTOR BA1A4M-TP
JR616 1-216-295-91 SHORT 0 Q393 8-729-140-04 TRANSISTOR 2SB1116-TP-LK
JR619 1-216-295-91 SHORT 0
Q394 8-729-900-80 TRANSISTOR BA1A4M-TP
JR632 1-216-295-91 SHORT 0 (US,CND) Q395 8-729-900-80 TRANSISTOR BA1A4M-TP
JR634 1-216-295-91 SHORT 0 Q396 8-729-116-57 TRANSISTOR 2SB1068TP-K
JR636 1-216-295-91 SHORT 0 (AED,AEP,CIS,G,UK) Q397 8-729-900-80 TRANSISTOR BA1A4M-TP
(US,CND,AR,AUS,E,EA,KR,MX,MY,SP,TH,TW)
JR641 1-216-295-91 SHORT 0 (AED,AEP,CIS,G,UK)
57
MAIN
Q503 8-729-900-80 TRANSISTOR BA1A4M-TP R125 1-216-065-91 RES-CHIP 4.7K 5% 1/10W
(EXCEPT US,CND) R132 1-216-049-91 RES-CHIP 1K 5% 1/10W
Q504 8-729-900-63 TRANSISTOR BN1F4M-TP (US,CND,AR,AUS,E,EA,KR,MX,MY,SP,TH,TW)
Q505 8-729-900-80 TRANSISTOR BA1A4M-TP R132 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
Q601 8-729-201-27 TRANSISTOR 2SC2715Y-TE85L (AED,AEP,CIS,G,UK)
Q602 8-729-422-57 TRANSISTOR BN1A4M-TP R133 1-216-049-91 RES-CHIP 1K 5% 1/10W
(US,CND,AR,AUS,E,EA,KR,MX,MY,SP,TH,TW)
Q611 8-729-120-28 TRANSISTOR 2SC2412K-T-146-QR R133 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
Q612 8-729-120-28 TRANSISTOR 2SC2412K-T-146-QR (AED,AEP,CIS,G,UK)
Q821 8-729-119-78 TRANSISTOR 2SC2785TP-HFE
Q822 8-729-119-78 TRANSISTOR 2SC2785TP-HFE R134 1-216-049-91 RES-CHIP 1K 5% 1/10W
Q823 8-729-119-76 TRANSISTOR 2SA1175TP-HFE R141 1-216-049-91 RES-CHIP 1K 5% 1/10W
R142 1-216-051-00 METAL CHIP 1.2K 5% 1/10W
Q824 8-729-900-80 TRANSISTOR BA1A4M-TP R143 1-216-089-91 RES-CHIP 47K 5% 1/10W
Q825 8-729-119-78 TRANSISTOR 2SC2785TP-HFE (EXCEPT US,CND)
Q828 8-729-119-78 TRANSISTOR 2SC2785TP-HFE R144 1-216-041-00 METAL CHIP 470 5% 1/10W
Q861 8-729-900-63 TRANSISTOR BN1F4M-TP R145 1-216-190-00 RES-CHIP 470 5% 1/8W
R146 1-216-041-00 METAL CHIP 470 5% 1/10W
Q862 8-729-141-30 TRANSISTOR 2SC3623ATP-LK R147 1-216-049-91 RES-CHIP 1K 5% 1/10W
Q863 8-729-141-30 TRANSISTOR 2SC3623ATP-LK (EXCEPT US,CND)
Q911 8-729-049-79 TRANSISTOR RT1P137S-TP R151 1-216-049-91 RES-CHIP 1K 5% 1/10W
Q912 8-729-900-80 TRANSISTOR BA1A4M-TP R152 1-216-097-91 RES-CHIP 100K 5% 1/10W
(AR,AUS,E,EA,KR,MX,MY,SP,TH,TW) R153 1-216-069-00 METAL CHIP 6.8K 5% 1/10W
R154 1-216-222-00 RES-CHIP 10K 5% 1/8W
Q962 8-729-140-04 TRANSISTOR 2SB1116-TP-LK R157 1-216-113-00 METAL CHIP 470K 5% 1/10W
(AR,AUS,E,EA,KR,MX,MY,SP,TH,TW) (EXCEPT US,CND)
R158 1-216-295-91 SHORT 0 (US,CND)
< RESISTOR > R158 1-216-097-91 RES-CHIP 100K 5% 1/10W
(EXCEPT US,CND)
R101 1-216-049-91 RES-CHIP 1K 5% 1/10W
R102 1-216-097-91 RES-CHIP 100K 5% 1/10W R159 1-216-073-00 METAL CHIP 10K 5% 1/10W
R103 1-216-069-00 METAL CHIP 6.8K 5% 1/10W (EXCEPT US,CND)
R104 1-216-073-00 METAL CHIP 10K 5% 1/10W R160 1-216-295-91 SHORT 0 (US,CND)
R107 1-216-113-00 METAL CHIP 470K 5% 1/10W R160 1-216-053-00 METAL CHIP 1.5K 5% 1/10W
(EXCEPT US,CND) (EXCEPT US,CND)
R161 1-216-073-00 METAL CHIP 10K 5% 1/10W
R108 1-216-295-91 SHORT 0 (US,CND) (EXCEPT US,CND)
R108 1-216-097-91 RES-CHIP 100K 5% 1/10W R162 1-216-089-91 RES-CHIP 47K 5% 1/10W
(EXCEPT US,CND) (EXCEPT US,CND)
R109 1-216-073-00 METAL CHIP 10K 5% 1/10W
(EXCEPT US,CND) R163 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R110 1-216-296-91 SHORT 0 (US,CND) R164 1-216-097-91 RES-CHIP 100K 5% 1/10W
R110 1-216-202-00 RES-CHIP 1.5K 5% 1/8W R165 1-216-073-00 METAL CHIP 10K 5% 1/10W
(EXCEPT US,CND) R166 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R171 1-216-075-00 METAL CHIP 12K 5% 1/10W
R111 1-216-073-00 METAL CHIP 10K 5% 1/10W (AR,AUS,E,EA,KR,MX,MY,SP,TW)
(EXCEPT US,CND)
(EXCEPT US,CND) (AR,AUS,E,EA,KR,MX,MY,SP,TW)
R113 1-216-057-00 METAL CHIP 2.2K 5% 1/10W R173 1-216-073-00 METAL CHIP 10K 5% 1/10W
R114 1-216-097-91 RES-CHIP 100K 5% 1/10W (AR,AUS,E,EA,KR,MX,MY,SP,TW)
R115 1-216-073-00 METAL CHIP 10K 5% 1/10W R175 1-216-065-91 RES-CHIP 4.7K 5% 1/10W
R201 1-216-025-91 RES-CHIP 100 5% 1/10W
R121 1-216-075-00 METAL CHIP 12K 5% 1/10W
(AR,AUS,E,EA,KR,MX,MY,SP,TW) R203 1-216-025-91 RES-CHIP 100 5% 1/10W
R122 1-216-073-00 METAL CHIP 10K 5% 1/10W R204 1-216-085-00 METAL CHIP 33K 5% 1/10W
(AR,AUS,E,EA,KR,MX,MY,SP,TW) R301 1-216-085-00 METAL CHIP 33K 5% 1/10W
R124 1-216-065-91 RES-CHIP 4.7K 5% 1/10W
R305 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
R306 1-216-071-00 METAL CHIP 8.2K 5% 1/10W
R307 1-216-065-91 RES-CHIP 4.7K 5% 1/10W
R308 1-216-071-00 METAL CHIP 8.2K 5% 1/10W
58
MAIN
R309 1-216-081-00 METAL CHIP 22K 5% 1/10W R387 1-216-033-00 METAL CHIP 220 5% 1/10W
R311 1-216-121-91 RES-CHIP 1M 5% 1/10W R388 1-216-081-00 METAL CHIP 22K 5% 1/10W
R314 1-216-295-91 SHORT 0 R390 1-216-107-00 METAL CHIP 270K 5% 1/10W
R315 1-216-073-00 METAL CHIP 10K 5% 1/10W R391 1-216-296-91 SHORT 0
R318 1-216-073-00 METAL CHIP 10K 5% 1/10W R394 1-216-033-00 METAL CHIP 220 5% 1/10W
R320 1-216-057-00 METAL CHIP 2.2K 5% 1/10W R407 1-216-065-91 RES-CHIP 4.7K 5% 1/10W
R332 1-216-025-91 RES-CHIP 100 5% 1/10W R413 1-216-295-91 SHORT 0
R334 1-216-100-00 RES-CHIP 130K 5% 1/10W R418 1-216-025-91 RES-CHIP 100 5% 1/10W
R335 1-216-033-00 METAL CHIP 220 5% 1/10W R419 1-216-025-91 RES-CHIP 100 5% 1/10W
R336 1-216-099-00 METAL CHIP 120K 5% 1/10W (AED,AEP,CIS,CND,G,UK,US,AR,AUS,E,EA,KR,MX,TH)
R338 1-216-081-00 METAL CHIP 22K 5% 1/10W R430 1-216-025-91 RES-CHIP 100 5% 1/10W
(AED,AEP,CIS,CND,G,UK,US,AR,AUS,E,EA,KR,MX,TH)
R341 1-216-033-00 METAL CHIP 220 5% 1/10W (AED,AEP,CIS,CND,G,UK,US,AR,AUS,E,EA,KR,MX,TH)
R342 1-216-075-00 METAL CHIP 12K 5% 1/10W
0 R343 1-219-787-17 FUSIBLE 5.6 5% 1/4W R435 1-216-033-00 METAL CHIP 220 5% 1/10W
0 R344 1-219-787-17 FUSIBLE 5.6 5% 1/4W (AED,AEP,CIS,CND,G,UK,US,AR,AUS,E,EA,KR,MX,TH)
R437 1-216-033-00 METAL CHIP 220 5% 1/10W
R352 1-216-057-00 METAL CHIP 2.2K 5% 1/10W (AED,AEP,CIS,CND,G,UK,US,AR,AUS,E,EA,KR,MX,TH)
R442 1-216-025-91 RES-CHIP 100 5% 1/10W
R353 1-216-025-91 RES-CHIP 100 5% 1/10W (AED,AEP,CIS,CND,G,UK,US,AR,AUS,E,EA,KR,MX,TH)
R354 1-216-025-91 RES-CHIP 100 5% 1/10W
R355 1-216-057-00 METAL CHIP 2.2K 5% 1/10W R443 1-216-025-91 RES-CHIP 100 5% 1/10W
R357 1-216-065-91 RES-CHIP 4.7K 5% 1/10W R445 1-216-025-91 RES-CHIP 100 5% 1/10W
R446 1-216-025-91 RES-CHIP 100 5% 1/10W
R359 1-216-085-00 METAL CHIP 33K 5% 1/10W
R467 1-216-295-91 SHORT 0
R364 1-216-045-00 METAL CHIP 680 5% 1/10W R468 1-216-295-91 SHORT 0
R366 1-216-049-91 RES-CHIP 1K 5% 1/10W
R367 1-216-089-91 RES-CHIP 47K 5% 1/10W R469 1-216-295-91 SHORT 0
R373 1-216-049-91 RES-CHIP 1K 5% 1/10W (AED,AEP,CIS,CND,G,UK,US)
R483 1-216-073-00 METAL CHIP 10K 5% 1/10W
R377 1-216-089-91 RES-CHIP 47K 5% 1/10W
R494 1-216-295-91 SHORT 0
R382 1-216-025-91 RES-CHIP 100 5% 1/10W R495 1-216-295-91 SHORT 0
R383 1-216-067-00 METAL CHIP 5.6K 5% 1/10W R497 1-216-053-00 METAL CHIP 1.5K 5% 1/10W
R384 1-216-100-00 RES-CHIP 130K 5% 1/10W (AUS,MY,SP,TW)
R385 1-216-296-91 SHORT 0
R386 1-216-099-00 METAL CHIP 120K 5% 1/10W

59
MAIN
(EA) R620 1-216-065-91 RES-CHIP 4.7K 5% 1/10W
(AR,E,MX) R622 1-216-057-00 METAL CHIP 2.2K 5% 1/10W
(US,CND) R625 1-216-073-00 METAL CHIP 10K 5% 1/10W
(AR,AUS,E,EA,MX,MY,SP,TW) R642 1-216-073-00 METAL CHIP 10K 5% 1/10W
R655 1-216-073-00 METAL CHIP 10K 5% 1/10W
R498 1-216-085-00 METAL CHIP 33K 5% 1/10W
(AED,AEP,CIS,G,UK) R656 1-216-222-00 RES-CHIP 10K 5% 1/8W
R499 1-216-025-91 RES-CHIP 100 5% 1/10W R658 1-216-174-00 RES-CHIP 100 5% 1/8W
R502 1-216-089-91 RES-CHIP 47K 5% 1/10W R660 1-216-065-91 RES-CHIP 4.7K 5% 1/10W
R504 1-216-025-91 RES-CHIP 100 5% 1/10W R662 1-216-065-91 RES-CHIP 4.7K 5% 1/10W
R505 1-216-065-91 RES-CHIP 4.7K 5% 1/10W R663 1-216-065-91 RES-CHIP 4.7K 5% 1/10W
R506 1-216-049-91 RES-CHIP 1K 5% 1/10W R664 1-216-065-91 RES-CHIP 4.7K 5% 1/10W
R523 1-216-073-00 METAL CHIP 10K 5% 1/10W R668 1-216-049-91 RES-CHIP 1K 5% 1/10W
R547 1-216-073-00 METAL CHIP 10K 5% 1/10W (AED,AEP,CIS,G,UK)
R682 1-216-073-00 METAL CHIP 10K 5% 1/10W
R548 1-216-073-00 METAL CHIP 10K 5% 1/10W (AED,AEP,CIS,G,UK)
R566 1-216-073-00 METAL CHIP 10K 5% 1/10W
R601 1-216-295-91 SHORT 0 (EXCEPT US,CND) R683 1-216-097-91 RES-CHIP 100K 5% 1/10W
R602 1-216-029-00 METAL CHIP 150 5% 1/10W (AED,AEP,CIS,G,UK)
R603 1-216-037-00 METAL CHIP 330 5% 1/10W R684 1-216-097-91 RES-CHIP 100K 5% 1/10W
(AR,AUS,E,EA,KR,MX,MY,SP,TH,TW) (AED,AEP,CIS,G,UK)
R685 1-216-067-00 METAL CHIP 5.6K 5% 1/10W
(AED,AEP,CIS,CND,G,UK,US) R686 1-216-166-00 RES-CHIP 47 5% 1/8W
R604 1-216-017-91 RES-CHIP 47 5% 1/10W (AED,AEP,CIS,G,UK)
R605 1-216-045-00 METAL CHIP 680 5% 1/10W R688 1-216-065-91 RES-CHIP 4.7K 5% 1/10W
R607 1-216-053-00 METAL CHIP 1.5K 5% 1/10W
R689 1-216-065-91 RES-CHIP 4.7K 5% 1/10W
R608 1-216-017-91 RES-CHIP 47 5% 1/10W (AED,AEP,CIS,G,UK)
R609 1-216-295-91 SHORT 0 (US,CND) R801 1-260-304-51 CARBON 10 5% 1/2W
R611 1-216-182-00 RES-CHIP 220 5% 1/8W R802 1-260-304-51 CARBON 10 5% 1/2W
R612 1-216-214-00 RES-CHIP 4.7K 5% 1/8W (AED,AEP,CIS,G,UK)
R821 1-216-089-91 RES-CHIP 47K 5% 1/10W
R614 1-216-041-00 METAL CHIP 470 5% 1/10W
(E) R823 1-216-073-00 METAL CHIP 10K 5% 1/10W
R614 1-216-039-00 METAL CHIP 390 5% 1/10W R824 1-216-073-00 METAL CHIP 10K 5% 1/10W
(US,CND,AR,AUS,EA,KR,MX,MY,SP,TH,TW) R825 1-216-065-91 RES-CHIP 4.7K 5% 1/10W
(AED,AEP,CIS,G,UK) R827 1-216-081-00 METAL CHIP 22K 5% 1/10W
R615 1-216-049-91 RES-CHIP 1K 5% 1/10W
R829 1-216-081-00 METAL CHIP 22K 5% 1/10W
R616 1-216-065-91 RES-CHIP 4.7K 5% 1/10W R831 1-216-067-00 METAL CHIP 5.6K 5% 1/10W
(E) (EXCEPT US,CND)
(US,CND,AR,AUS,EA,KR,MX,MY,SP,TH,TW) (EXCEPT US,CND)
R617 1-216-035-00 METAL CHIP 270 5% 1/10W R843 1-216-065-91 RES-CHIP 4.7K 5% 1/10W
(AED,AEP,CIS,G,UK) (EXCEPT US,CND)
R618 1-216-049-91 RES-CHIP 1K 5% 1/10W
60
MAIN MOTOR PANEL
R844 1-216-097-91 RES-CHIP 100K 5% 1/10W < VIBRATOR >
(EXCEPT US,CND)
R845 1-216-121-91 RES-CHIP 1M 5% 1/10W X401 1-567-098-41 VIBRATOR, CRYSTAL(32.768 KHz)
(EXCEPT US,CND) X402 1-781-107-21 VIBRATOR, SERAMIC(16 MHz )
R851 1-260-304-51 CARBON 10 5% 1/2W X651 1-760-549-31 VIBRATOR, CRYSTAL(4.5 MHz)
(AED,AEP,CIS,G,UK)
R852 1-260-304-51 CARBON 10 5% 1/2W < VIBRATOR >
(AED,AEP,CIS,G,UK)
R861 1-216-049-91 RES-CHIP 1K 5% 1/10W XT681 1-579-900-21 VIBRATOR, CRYSTAL(4.332 MHz)
(AED,AEP,CIS,G,UK)
R862 1-216-073-00 METAL CHIP 10K 5% 1/10W **************************************************************
R863 1-216-089-91 RES-CHIP 47K 5% 1/10W
R864 1-216-049-91 RES-CHIP 1K 5% 1/10W 1-675-910-11 MOTOR BOARD
R865 1-216-049-91 RES-CHIP 1K 5% 1/10W *************
R866 1-216-019-00 METAL CHIP 56 5% 1/10W
< CAPACITOR >
R868 1-215-891-11 METAL OXIDE 680 5% 2W
R869 1-215-891-11 METAL OXIDE 680 5% 2W C721 1-162-306-11 CERAMIC 0.01uF 30.00% 16V
R912 1-216-295-91 SHORT 0
R961 1-216-065-91 RES-CHIP 4.7K 5% 1/10W < CONNECTOR >
R962 1-216-089-91 RES-CHIP 47K 5% 1/10W CN721 1-770-516-31 CONNECTOR, FFC 8P
(AR,AUS,E,EA,KR,MX,MY,SP,TH,TW) CN722 1-785-330-11 PIN, CONNECTOR (LIGHT ANGLE)4P
R963 1-216-057-00 METAL CHIP 2.2K 5% 1/10W < SWITCH >

R964 1-216-089-91 RES-CHIP 47K 5% 1/10W S701 1-771-822-11 SWITCH, LEVER (SLIDE)
(AR,AUS,E,EA,KR,MX,MY,SP,TH,TW) **************************************************************
R965 1-216-089-91 RES-CHIP 47K 5% 1/10W
(AR,AUS,E,EA,KR,MX,MY,SP,TH,TW) A-4428-055-A PANEL BOARD, COMPLETE
R966 1-216-019-00 METAL CHIP 56 5% 1/10W (AED,AEP,CND,G,UK,US,CIS)
R967 1-216-025-91 RES-CHIP 100 5% 1/10W **********************
(AR,AUS,E,EA,KR,MX,MY,SP,TH,TW) A-4428-066-A PANEL BOARD, COMPLETE
< COMPOSITION CIRCUIT BLOCK > **********************
A-4428-593-A PANEL BOARD, COMPLETE (TH)
RB641 1-234-457-11 ENCAPSULATED COMPONENT **********************
< VARIABLE RESISTOR > 4-224-584-01 HOLDER (FL)
RV301 1-241-764-11 RES, ADJ, CARBON 10K < CAPACITOR >

RV302 1-241-762-11 RES, ADJ, CARBON 2.2K
RV303 1-241-762-11 RES, ADJ, CARBON 2.2K C601 1-124-589-11 ELECT 47uF 20% 16V
RV304 1-241-768-11 RES, ADJ, CARBON 220K C602 1-126-163-11 ELECT 4.7uF 20% 50V
RV351 1-241-764-11 RES, ADJ, CARBON 10K C603 1-162-306-11 CERAMIC 0.01uF 30.00% 16V
C604 1-162-294-31 CERAMIC 0.001uF 10% 50V
RV352 1-241-762-11 RES, ADJ, CARBON 2.2K C605 1-162-306-11 CERAMIC 0.01uF 30.00% 16V
RV353 1-241-762-11 RES, ADJ, CARBON 2.2K
RV354 1-241-768-11 RES, ADJ, CARBON 220K C607 1-124-589-11 ELECT 47uF 20% 16V
RV611 1-238-601-11 RES, ADJ, CARBON 22K C608 1-162-306-11 CERAMIC 0.01uF 30.00% 16V
C609 1-162-306-11 CERAMIC 0.01uF 30.00% 16V
< RELAY > C610 1-126-157-11 ELECT 10uF 20% 16V
RY801 1-755-373-11 RELAY C611 1-126-157-11 ELECT 10uF 20% 16V
< TRANSFORMER > C612 1-162-303-11 CERAMIC 0.0033uF 30.00% 16V

C613 1-126-157-11 ELECT 10uF 20% 16V
T301 1-423-980-11 TRANSFORMER, BIAS OSCILLATION C614 1-126-157-11 ELECT 10uF 20% 16V
T601 1-435-195-11 TRANSFORMER, DISCRIMINATOR C615 1-126-163-11 ELECT 4.7uF 20% 50V
T602 1-234-477-11 ENCAPSULATED COMPONENT C616 1-162-306-11 CERAMIC 0.01uF 30.00% 16V
(AED,AEP,CIS,G,UK)
C617 1-162-306-11 CERAMIC 0.01uf 30.00% 16V
< TERMINAL > C620 1-126-157-11 ELECT 10uF 20% 16V
C631 1-162-294-31 CERAMIC 0.001uF 10% 50V
TM601 1-694-555-11 TERMINAL BOARD (4P) (FM/AM) C632 1-162-294-31 CERAMIC 0.001uF 10% 50V
(US,CND,AR,AUS,E,EA,KR,MX,MY,SP,TH,TW) C633 1-164-159-11 CERAMIC 0.1uF 50V
TM601 1-694-556-21 TERMINAL BOARD (ANT.PAL)(FM/AM)
(AED,AEP,CIS,G,UK)
TM801 1-694-635-11 TERMINAL BOARD (4P) (SPEAKER)
61
PANEL
C652 1-126-966-11 ELECT 33uF 20.00% 50V D617 8-719-071-41 DIODE SELS5923C-TP15 (MD(VIDEO))
C653 1-126-966-11 ELECT 33uF 20.00% 50V D618 8-719-071-41 DIODE SELS5923C-TP15 (TAPE)
C655 1-162-282-31 CERAMIC 100PF 10% 50V D619 8-719-071-41 DIODE SELS5923C-TP15 (CD)
C656 1-162-282-31 CERAMIC 100PF 10% 50V D620 8-719-071-41 DIODE SELS5923C-TP15 (TUNER)
C657 1-162-282-31 CERAMIC 100PF 10% 50V
< FERRITE BEAD >
C658 1-162-282-31 CERAMIC 100PF 10% 50V
C659 1-162-282-31 CERAMIC 100PF 10% 50V FB601 1-412-473-21 INDUCTOR 0UH
C660 1-162-282-31 CERAMIC 100PF 10% 50V
C661 1-162-282-31 CERAMIC 100PF 10% 50V < FILTER >
C662 1-162-282-31 CERAMIC 100PF 10% 50V
FL601 1-517-928-11 INDICATOR TUBE, FLUORESCENT
C663 1-162-282-31 CERAMIC 100PF 10% 50V
C664 1-162-282-31 CERAMIC 100PF 10% 50V < IC >
C665 1-162-282-31 CERAMIC 100PF 10% 50V
C666 1-162-282-31 CERAMIC 100PF 10% 50V IC601 8-759-652-49 IC TMP88CP77F-1A22
C667 1-162-282-31 CERAMIC 100PF 10% 50V IC602 8-759-570-21 IC BA3830F-E2
IC603 8-759-648-23 IC RPM6940-H4
C668 1-162-282-31 CERAMIC 100PF 10% 50V IC722 8-759-099-06 IC M5218AFP-TE1
C669 1-162-282-31 CERAMIC 100PF 10% 50V (AR,AUS,E,EA,KR,MX,MY,SP,TH,TW)
C670 1-162-282-31 CERAMIC 100PF 10% 50V
C671 1-162-282-31 CERAMIC 100PF 10% 50V < JACK >
C697 1-162-282-31 CERAMIC 100PF 10% 50V
J631 1-785-569-11 JACK (SMALL TYPE) (PHONES)
C719 1-164-658-11 ELECT 100u 20% 10V J721 1-785-569-11 JACK (SMALL TYPE) (MIC)
(AR,AUS,E,EA,KR,MX,MY,SP,TH,TW) (AR,AUS,E,EA,KR,MX,MY,SP,TH,TW)
C720 1-164-658-11 ELECT 100u 20% 10V
(AR,AUS,E,EA,KR,MX,MY,SP,TH,TW) < TRANSISTOR >
C736 1-124-261-00 ELECT 10uF 20% 50V
(AR,AUS,E,EA,KR,MX,MY,SP,TH,TW) Q604 8-729-900-80 TRANSISTOR BA1A4M-TP
C737 1-124-261-00 ELECT 10uF 20% 50V Q605 8-729-900-80 TRANSISTOR BA1A4M-TP
(AR,AUS,E,EA,KR,MX,MY,SP,TH,TW) Q606 8-729-029-68 TRANSISTOR DTC114TSA-TP
C738 1-124-257-00 ELECT 2.2uF 20% 50V Q607 8-729-029-68 TRANSISTOR DTC114TSA-TP
C739 1-162-215-31 CERAMIC 47PF 5% 50V Q609 8-729-029-68 TRANSISTOR DTC114TSA-TP

C740 1-162-282-31 CERAMIC 100PF 10% 50V Q611 8-729-029-68 TRANSISTOR DTC114TSA-TP
(AR,AUS,E,EA,KR,MX,MY,SP,TH,TW) Q612 8-729-047-58 TRANSISTOR DTC114TLTL2
C741 1-124-463-00 ELECT 0.1uF 20% 50V Q613 8-729-047-58 TRANSISTOR DTC114TLTL2
C742 1-162-215-31 CERAMIC 47PF 5% 50V Q614 8-729-047-58 TRANSISTOR DTC114TLTL2
C743 1-162-290-31 CERAMIC 470PF 10% 50V Q625 8-729-900-80 TRANSISTOR BA1A4M-TP
Q627 8-729-900-80 TRANSISTOR BA1A4M-TP
C744 1-162-294-31 CERAMIC 0.001uF 10% 50V
C745 1-124-257-00 ELECT 2.2uF 20% 50V Q629 8-729-900-80 TRANSISTOR BA1A4M-TP
C746 1-162-306-11 CERAMIC 0.01uF 30.00% 16V Q721 8-729-119-78 TRANSISTOR 2SC2785TP-HFE
(AR,AUS,E,EA,KR,MX,MY,SP,TH,TW) (AR,AUS,E,EA,KR,MX,MY,SP,TH,TW)
C749 1-164-159-11 CERAMIC 0.1uF 50V
(AR,AUS,E,EA,KR,MX,MY,SP,TH,TW) < RESISTOR >
C750 1-124-257-00 ELECT 2.2uF 20% 50V
R602 1-249-429-11 CARBON 10K 5% 1/4W
< CONNECTOR > R603 1-249-429-11 CARBON 10K 5% 1/4W
R604 1-247-807-31 CARBON 100 5% 1/4W
CN601 1-793-767-11 CONNECTOR, BOARD TO BOARD 30P R605 1-247-903-00 CARBON 1M 5% 1/4W
< DIODE > R606 1-247-807-31 CARBON 100 5% 1/4W

R607 1-249-429-11 CARBON 10K 5% 1/4W
D601 8-719-071-44 DIODE SELS5223C-TP15 (STANDBY) R608 1-247-807-31 CARBON 100 5% 1/4W
D602 8-719-071-44 DIODE SELS5223C-TP15 (TIMER) R609 1-249-429-11 CARBON 10K 5% 1/4W
D614 8-719-058-04 DIODE SEL5223S-TP15 (REC/PAUSE) R610 1-247-807-31 CARBON 100 5% 1/4W
D615 8-719-057-97 DIODE SEL5923A-TP15 (GROOVE)
D616 8-719-057-97 DIODE SEL5923A-TP15 (SURROUND)
62
PANEL
R611 1-249-429-11 CARBON 10K 5% 1/4W R682 1-249-413-11 CARBON 470 5% 1/4W F
R612 1-249-401-11 CARBON 47 5% 1/4W F R683 1-249-414-11 CARBON 560 5% 1/4W F
R614 1-247-893-11 CARBON 390K 5% 1/4W R685 1-249-417-11 CARBON 1K 5% 1/4W F
R615 1-249-441-11 CARBON 100K 5% 1/4W R686 1-249-418-11 CARBON 1.2K 5% 1/4W F
R616 1-249-440-11 CARBON 82K 5% 1/4W R687 1-249-420-11 CARBON 1.8K 5% 1/4W F
(AR,AUS,E,EA,KR,MX,MY,SP,TH,TW) R688 1-249-422-11 CARBON 2.7K 5% 1/4W F
R617 1-249-429-11 CARBON 10K 5% 1/4W R689 1-247-843-11 CARBON 3.3K 5% 1/4W
(AR,AUS,E,EA,KR,MX,MY,SP,TH,TW) R690 1-249-425-11 CARBON 4.7K 5% 1/4W F
R618 1-249-441-11 CARBON 100K 5% 1/4W (AR,AUS,E,EA,KR,MX,MY,SP,TH,TW)
(AR,AUS,E,EA,KR,MX,MY,SP,TH,TW) R691 1-216-345-61 FUSIBLE 0.47 5% 1W
R619 1-249-441-11 CARBON 100K 5% 1/4W
R620 1-249-437-11 CARBON 47K 5% 1/4W R707 1-249-411-11 CARBON 330 5% 1/4W
R708 1-249-409-11 CARBON 220 5% 1/4W F
R623 1-249-420-11 CARBON 1.8K 5% 1/4W F R710 1-249-409-11 CARBON 220 5% 1/4W F
R624 1-249-401-11 CARBON 47 5% 1/4W F R711 1-249-409-11 CARBON 220 5% 1/4W F
R625 1-249-435-11 CARBON 33K 5% 1/4W
R713 1-249-409-11 CARBON 220 5% 1/4W F
R633 1-247-828-11 CARBON 750 5% 1/4W R720 1-249-417-11 CARBON 1K 5% 1/4W F
R634 1-249-414-11 CARBON 560 5% 1/4W F (AR,AUS,E,EA,KR,MX,MY,SP,TH,TW)
R635 1-249-409-11 CARBON 220 5% 1/4W F R721 1-249-429-11 CARBON 10K 5% 1/4W F
R638 1-249-441-11 CARBON 100K 5% 1/4W
R639 1-249-441-11 CARBON 100K 5% 1/4W R734 1-247-807-31 CARBON 100 5% 1/4W
R641 1-249-441-11 CARBON 100K 5% 1/4W R735 1-247-885-00 CARBON 180K 5% 1/4W
R736 1-249-429-11 CARBON 10K 5% 1/4W
R644 1-249-441-11 CARBON 100K 5% 1/4W R737 1-249-433-11 CARBON 22K 5% 1/4W
R653 1-249-411-11 CARBON 330 5% 1/4W R739 1-249-441-11 CARBON 100K 5% 1/4W
R655 1-249-414-11 CARBON 560 5% 1/4W F R740 1-249-417-11 CARBON 1K 5% 1/4W F
R657 1-249-417-11 CARBON 1K 5% 1/4W F R741 1-249-429-11 CARBON 10K 5% 1/4W
R658 1-249-418-11 CARBON 1.2K 5% 1/4W F R744 1-249-441-11 CARBON 100K 5% 1/4W
R659 1-249-420-11 CARBON 1.8K 5% 1/4W F (AR,AUS,E,EA,KR,MX,MY,SP,TH,TW)
R660 1-249-422-11 CARBON 2.7K 5% 1/4W F R745 1-247-807-31 CARBON 100 5% 1/4W
R661 1-247-843-11 CARBON 3.3K 5% 1/4W (AR,AUS,E,EA,KR,MX,MY,SP,TH,TW)
R662 1-249-425-11 CARBON 4.7K 5% 1/4W F
< VARIABLE RESISTOR >
R664 1-249-429-11 CARBON 10K 5% 1/4W
R665 1-249-410-11 CARBON 270 5% 1/4W F RV722 1-225-739-11 RES, VAR CARBON 50K
R666 1-249-411-11 CARBON 330 5% 1/4W (AR,AUS,E,EA,KR,MX,MY,SP,TH,TW)
R667 1-249-413-11 CARBON 470 5% 1/4W F
R668 1-249-414-11 CARBON 560 5% 1/4W F < SWITCH >
R669 1-249-415-11 CARBON 680 5% 1/4W F S601 1-418-725-11 ENCODER, ROTARY (12 TYPE) (VOLUME)
R670 1-249-417-11 CARBON 1K 5% 1/4W F S611 1-762-875-21 SWITCH, KEYBOARD (FF)
R671 1-249-418-11 CARBON 1.2K 5% 1/4W F S612 1-762-875-21 SWITCH, KEYBOARD (REW)
R672 1-249-420-11 CARBON 1.8K 5% 1/4W F S613 1-762-875-21 SWITCH, KEYBOARD (EDIT)
R673 1-249-422-11 CARBON 2.7K 5% 1/4W F S614 1-762-875-21 SWITCH, KEYBOARD (STEREO/MONO)
R674 1-247-843-11 CARBON 3.3K 5% 1/4W S615 1-762-875-21 SWITCH, KEYBOARD (PLAY MODE)
R675 1-249-425-11 CARBON 4.7K 5% 1/4W F S616 1-762-875-21 SWITCH, KEYBOARD (GROOVE)
R679 1-249-429-11 CARBON 10K 5% 1/4W S617 1-762-875-21 SWITCH, KEYBOARD (SURROUND)
R680 1-249-410-11 CARBON 270 5% 1/4W F S618 1-762-875-21 SWITCH, KEYBOARD (HI-DUB)
R681 1-249-411-11 CARBON 330 5% 1/4W S619 1-762-875-21 SWITCH, KEYBOARD (REC PAUSE)
63
PANEL SENSOR SUB-TRANS TRANS
S620 1-762-875-21 SWITCH, KEYBOARD (ENTER) < IC >
S621 1-762-875-21 SWITCH, KEYBOARD (EQ EDIT)
S623 1-762-875-21 SWITCH, KEYBOARD (– .) IC971 8-759-158-62 IC TA78057S
S624 1-762-875-21 SWITCH, KEYBOARD (x)
S625 1-762-875-21 SWITCH, KEYBOARD (gG) < TRANSISTOR >
S626 1-762-875-21 SWITCH, KEYBOARD (S) Q971 8-729-119-78 TRANSISTOR 2SC2785TP-HFE

S627 1-762-875-21 SWITCH, KEYBOARD (> +)
S628 1-762-875-21 SWITCH, KEYBOARD (TUNER) < RESISTOR >
S629 1-762-875-21 SWITCH, KEYBOARD (CD)
S630 1-762-875-21 SWITCH, KEYBOARD (TAPE A/B) R975 1-249-429-11 CARBON 10K 5% 1/4W
S631 1-762-875-21 SWITCH, KEYBOARD (MD(VIDEO)) < RELAY >

S632 1-762-875-21 SWITCH, KEYBOARD (DOWN)
S633 1-762-875-21 SWITCH, KEYBOARD (UP) 0 RY971 1-755-276-11 RELAY, POWER
S637 1-762-875-21 SWITCH, KEYBOARD (POWER)
S638 1-762-875-21 SWITCH, KEYBOARD (DISPLAY) < TRANSFORMER >
S639 1-762-875-21 SWITCH, KEYBOARD (SPECTRUM) 0 T972 1-435-209-11 TRANSFORMER, POWER (US,CND)
S640 1-762-875-21 SWITCH, KEYBOARD (LEFT) 0 T972 1-435-210-11 TRANSFORMER, POWER (AED,AEP,CIS,G,UK)
S641 1-762-875-21 SWITCH, KEYBOARD (RIGHT) **************************************************************
S642 1-762-875-21 SWITCH, KEYBOARD (DISK SKIP)
S643 1-762-875-21 SWITCH, KEYBOARD (DISC 1) A-4428-045-A TRANS BOARD, COMPLETE
(AED,AEP,G,UK,CIS)
S644 1-762-875-21 SWITCH, KEYBOARD (DISC 2) **********************
S645 1-762-875-21 SWITCH, KEYBOARD (DISC 3) A-4428-059-A TRANS BOARD, COMPLETE (US)
S646 1-762-875-21 SWITCH, KEYBOARD (OPEN/CLOSE) **********************
S647 1-762-875-21 SWITCH, KEYBOARD (KARAOKE) A-4428-069-A TRANS BOARD, COMPLETE
(AR,AUS,E,EA,KR,MX,MY,SP,TH,TW) (AR,E,EA,MY,SP,TW)
**********************
< VIBRATOR > A-4428-254-A TRANS BOARD, COMPLETE (CND)
**********************
X601 1-579-352-11 VIBRATOR, CERAMIC(12.5 MHz) A-4428-255-A TRANS BOARD, COMPLETE (AUS)
************************************************************** **********************
A-4428-261-A TRANS BOARD, COMPLETE (KR)
1-678-153-11 SENSOR BOARD **********************
(AR,AUS,E,EA,KR,MX,MY,SP,TH,TW) A-4428-264-A TRANS BOARD, COMPLETE (MX)
************* **********************
A-4428-597-A TRANS BOARD, COMPLETE (TH)
< THERMISTOR > **********************
TH501 1-807-796-11 THERMISTOR 1-533-217-31 HOLDER, FUSE

************************************************************** 7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S
A-4428-044-A SUB-TRANS BOARD, COMPLETE < CAPACITOR >

(AED,AEP,G,UK,CIS)
************************** C975 1-164-159-11 CERAMIC 0.1uF 50V
A-4428-058-A SUB-TRANS BOARD, COMPLETE (US,CND) C976 1-126-969-11 ELECT 220uF 20.00% 50V
************************** C978 1-126-964-11 ELECT 10uF 20.00% 50V
C979 1-126-968-11 ELECT 100uF 20.00% 50V
< CAPACITOR > C980 1-164-159-11 CERAMIC 0.1uF 50V
0 C971 1-113-925-11 CERAMIC 0.01uF 20.00% 250V < CONNECTOR >

C972 1-126-768-11 ELECT 2200uF 20.00% 16V
C973 1-126-933-11 ELECT 100uF 20.00% 16V CN971 1-564-321-00 PIN, CONNECTOR 2P
< CONNECTOR > * CN972 1-564-526-11 PLUG, CONNECTOR 11P
CN974 1-564-321-00 PIN, CONNECTOR 2P * CN972 1-564-528-11 PLUG, CONNECTOR 13P
* CN975 1-564-321-21 PIN, CONNECTOR 2P (AED,AEP,CIS,CND,G,UK,US)
CN976 1-785-329-11 PIN, CONNECTOR (LIGHT ANGLE)3P
< DIODE >
< DIODE >
D977 8-719-024-99 DIODE 11ES2-NTA2B
0 D971 8-719-911-19 DIODE 1SS133T-72 D978 8-719-983-99 DIODE MTZJ-T-72-39D
D972 8-719-024-99 DIODE 11ES2-NTA2B D979 8-719-110-31 DIODE MTZJ-T-72-12B
D973 8-719-024-99 DIODE 11ES2-NTA2B
D974 8-719-024-99 DIODE 11ES2-NTA2B
D975 8-719-024-99 DIODE 11ES2-NTA2B
64
TRANS
< FUSE > MISCELLANEOUS
**************
0 F971 1-533-451-11 FUSE, GLASS TUBE (DIA. 5)(3.15A 125V)(CND) M961 1-698-792-11 FAN, DC (AR,AUS,E,EA,KR,MX,MY,SP,TH,TW)
0 F971 1-533-452-11 FUSE, GLASS TUBE (DIA. 5)(4A 125V)(US) 101 1-773-042-11 WIRE (FLAT TYPE) (17 CORE)
0 F971 1-533-466-11 FUSE, GLASS TUBE (DIA. 5)(1.25A 250V) 104 1-791-897-11 WIRE (FLAT TYPE) (19 CORE)
(AED,AEP,CIS,G,UK) 0 108 1-690-608-11 CORD, POWER (AUS)
0 F971 1-533-471-11 FUSE, GLASS TUBE (DIA. 5)(4A 250V) 0 108 1-769-079-21 CORD, POWER (KR)
(AR,E,EA,MX,MY,SP,TW) 0 108 1-777-071-51 CORD, POWER
0 F972 1-533-469-11 FUSE, GLASS TUBE (DIA. 5)(2.5A 250V) (AED,AEP,CIS,G,UK,EA,MY,SP,TW)
(AR,E,EA,KR,MY,SP,TH,TW) 0 108 1-783-532-11 CORD, POWER (CND,US)
0 F973 1-533-468-11 FUSE, GLASS TUBE (DIA. 5)(2A 250) 0 108 1-783-820-11 CORD, POWER (CND,US)
(AR,AUS,E,EA,MY,SP,TW) 0 108 1-783-941-21 CORD, POWER (AR)
0 108 1-791-901-11 CORD, POWER (E,MX,TH)
< TRANSISTOR > 0 109 1-569-008-21 ADAPTOR, CONVERSION 2P(EA,MY,SP,TW)
0 109 1-569-008-31 ADAPTOR, CONVERSION (EA,MY,SP,TW)
Q972 8-729-048-52 TRANSISTOR 2SA1932(TP)
0 110 1-770-019-11 ADAPTOR, CONVERSION PLUG 3P (CIS,UK)
< RESISTOR > 209 1-791-983-12 WIRE (FLAT TYPE) (8 CORE)
216 1-471-035-11 MAGNET ASSY
0 R971 1-219-122-91 FUSIBLE 0.33 5% 1/4W **************************************************************
0 R972 1-219-119-81 FUSIBLE 0.1 5% 1/4W
R976 1-202-725-00 SOLID 3.3M 10% 1/2W **************
(US,CND) HARDWARE LIST
0 R977 1-217-637-00 FUSIBLE 1 5% 1/4W **************
R978 1-249-429-11 CARBON 10K 5% 1/4W
#1 7-628-254-05 SCREW +PS 2.6X5
R979 1-249-417-11 CARBON 1K 5% 1/4W F #2 7-685-646-79 SCREW +BVTP 3X8 TYPE2 N-S
R980 1-249-429-11 CARBON 10K 5% 1/4W #3 7-685-647-79 SCREW +BVTP 3X10 TYPE2 N-S
#4 7-685-650-79 SCREW +BVTP 3X16 TYPE2 IT-3
< SWITCH > #5 7-685-871-01 SCREW +BVTT 3X6 (S)
0 S971 1-771-291-11 SWITCH, POWER (VOL SEL) #6 7-685-872-09 SCREW +BVTT 3X8 (S)
(AR,E,EA,MY,SP,TW) #7 7-685-880-09 SCREW +BVTT 4X6 (S)
< TRANSFORMER >
0 T971 1-435-205-11TRANSFORMER, POWER (US)

0 T971 1-435-206-11TRANSFORMER, POWER (CND) The components identified by Les composants identifiés par
0 T971 1-435-207-11TRANSFORMER, POWER (AED,AEP,CIS,G,UK) mark 0 or dotted line with mark une marque 0 sont critiques
0 T971 1-435-208-11TRANSFORMER, POWER Replace only with part number Ne les remplacer que par une
(AR,AUS,E,EA,KR,MX,MY,SP,TH,TW) specified. pièce portant le numéro spécifié.
**************************************************************
65
HCD-BX3/DX3
REVISION HISTORY
Clicking the version allows you to jump to the revised page.
Also, clicking the version at the upper right on the revised page allows you to jump to the next revised
page.
Ver. Date Description of Revision

1.1 2001.11 Addition of Ref.No.223 for service part (RPC-01004)
1.0 2000.1 New

Sony HCD Bx3 Dx3

Uploaded by

Copyright:

Available Formats

Sony HCD Bx3 Dx3

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Sony HCD Bx3 Dx3

Uploaded by

Copyright:

Available Formats

HCD-BX3/DX3

SERVICE MANUAL US Model

• HCD-BX3/DX3 are the tuner, deck,

Model Name Using Similar Mechanism NEW

General 3. Measuring the voltage drop across a resistor by means of a

Power consumption To Exposed Metal

Fig. A. Using an AC voltmeter to check AC leakage.

SAFETY-RELATED COMPONENT WARNING!! ATTENTION AU COMPOSANT AYANT RAPPORT

NOTES ON LASER DIODE EMISSION CHECK 7. DIAGRAMS

Flexible Circuit Board Repairing

MODEL PARTS No.

Note for installing the panel board

Screw hole Hot melt

Attach the panel board with

1 – . button ws MD/VIDEO button and indicator

The clock uses a 24-hour system on the

4 Press . or > repeatedly to set

When carrying this system

3-1. UPPER CASE (TOP)

5 Two screws (Case) q;

1 Two screws (Case)

3-2. LOADING PANEL ASSY

CD mechanism deck (CDM58)

Front panel side

2 Pull-out the disc tray.

4 Screw (+BVTP 3 × 10)

2 Connector (CN302) 1 Flat type wire (CN304)

5 Screw (+BVTP 3 × 10)

Front panel section

6 Three screws (+BVTT 3 × 6)

3-4. TAPE MECHANISM DECK

3 Screw (+BVTP 2.6 × 8)

5 Five screws (+BVTP 2.6 × 8)

2 Bracket (Heart cam R)

6 Tape mechanism deck

Note: When attching the panel board,

3-6. SUB-TRANS BOARD AND TRANS BOARD

9 Two screws (+BVTT 4 × 6)

4 Three screws (+BVTP 3 × 10) 7 Heat sink

6 Two screws (+BVTP 3 × 10)

3 Two screws (+BVTP 3 × 10)

1 Two screws (+BVTP 3 × 8)

2 Remove the two solderings.

3 Remove the four solderings.

7 Head (A) board

9 Head (B) board

8 Screw (+PS 2.6 × 5)

1 Flat type wire (CN101)

2 Four screws (+PTPWH 2.6)

3-10. DRIVER BOARD, MOTOR BOARD AND ADDRESS SENSOR BOARD

q; Screw (+PTPWH 2.6 × 8)

5 Three screws (+BVTP 2.6 × 8)

4 Flat type wire (CN721)

1 Screw (+BVTP 2.6 × 8)

9 Pull-out the disc tray.

[VACS ON/OFF Mode]

1. Operating method of Aging Mode

3. Aging Mode in CD section

3. Aging Mode in Tape Deck section