Search Results (208)

Topology control is important for extending networks lifetime and reducing interference. The accuracy of topology identification plays a crucial role in topology control. Traditional passive interception can only identify the connectivity among cooperative sensor networks with known protocol. This paper proposes a novel method called Active Interfere and Passive Interception (AIPI) to identify the topology of non-cooperative sensor networks by using both active and passive interceptions. Active interception uses full duplex sensors to disrupt communication until frequency hopped to acquire distance information, and thus, infer their connectivity and calculate the location after modifying error in a non-cooperative sensor network. Passive interception uses Granger causality to infer the connectivity between two communication nodes after getting the time frame structure in physical layer. Passive interception is applied to conserve power consumption after obtaining physical information via active interception. Simulation results indicate that AIPI can identify the topology of non-cooperative sensor networks with a higher accuracy than traditional method. Full article

In this paper, we consider the issue of the physical layer security (PLS) problem between two nodes, i.e., transmitter (Alice) and receiver (Bob), in the presence of an eavesdropper (Eve) in a near-field communication (NFC) system. Notably, massive multiple-input multiple-output (MIMO) arrays significantly increase array aperture, thereby rendering the eavesdroppers more inclined to lurk near the transmission end. This situation necessitates using near-field channel models to more accurately describe channel characteristics. We consider two schemes with imperfect channel estimation information (CSI). The first scheme involves a conventional multiple-input multiple-output multiple-antenna eavesdropper (MIMOME) setup, where Alice simultaneously transmits information signal and artificial noise (AN). In the second scheme, Bob operates in a full-duplex (FD) mode, with Alice transmitting information signal while Bob emits AN. We then jointly design beamforming and AN vectors to degrade the reception signal quality at Eve, based on the signal-to-interference-plus-noise ratio (SINR) of each node. To tackle the power minimization problem, we propose an iterative algorithm that includes an additional constraint to ensure adherence to specified quality-of-service (QoS) metrics. Additionally, we decompose the robust optimization problem of the two schemes into two sub-problems, with one that can be solved using generalized Rayleigh quotient methods and the other that can be addressed through semi-definite programming (SDP). Finally, our simulation results confirm the viability of the proposed approach and demonstrate the effectiveness of the protection zone for NFC systems operating with CSI. Full article

We investigate the cooperative non-orthogonal multiple access (CNOMA) transmission through a full-duplex (FD) decode-and-forward (DaF) mode relay and propose two sub-optimal beamforming schemes for this CNOMA FD relay channel. For the optimization metric, we use the end-to-end information rate based on the mutual information from information theory. In addition to the pure CNOMA relay channel, the proposed beamforming schemes are applied to the security attack case as well, where an unauthorized eavesdropper tries to overhear the CNOMA transmission. The FD operation incurs the self-interference (SI) at the relay and the DaF mode along with CNOMA transmission forces the weakest link among the links toward three involved nodes to determine the end-to-end throughput. These facts lay the foundation for the designing and optimization of the beamforming vectors at the access point (AP) and at the relay. The first proposed sub-optimal optimization algorithm for the beamformer relies on the quadratically constrained quadratic problem (QCQP) in its central part, and this OCQP is iteratively applied with different interference level values at the near CNOMA user as the constraint term until some conditions for the design objectives are met. In addition to the first algorithm, a zero-forcing-based beamforming algorithm is proposed for a reference scheme. The proposed two algorithms are slightly modified to address the security-attacked CNOMA FD relay channel when a illegal user overhears the legitimate transmission. Simulation results are presented to advocate for the efficiency of the proposed algorithms for the CNOMA channel both with and without a security attack from an eavesdropper. Full article

Energy harvesting (EH) from radio frequency (RF) signals provides a promising approach for supplying sustainable and convenient energy to low-power Internet of Things (IoT) devices. In this work, we investigate short-packet communications in a full-duplex (FD) relay system, where RF signals from a source are utilized to power an energy-constrained relay through the time switching protocol. Specifically, hardware impairments in each node and residual self-interference caused by FD are jointly considered. To ensure reliable transmission, two antennas are symmetrically arranged according to the position of the relay station, both of which are used for energy harvesting. Furthermore, we explored two practical schemes based on symmetric channel correlation, i.e., an independent channel for energy harvesting and an identical channel for energy harvesting. For both scenarios, we derive closed-form approximations for the overall average block error rate (BLER) and effective throughput. The validity of our analysis is confirmed through computer simulations, demonstrating that the proposed scheme enhances the reliability and throughput of the system compared with the existing scheme in the literature at low transmission rates and transmit signal-to-noise-ratios (SNRs). Full article

Joint communication and sensing (JCS) is becoming an important trend in 6G, owing to its efficient utilization of spectrums and hardware resources. Utilizing echoes of the same signal can achieve the object location sensing function, in addition to the V2X communication function. There is application potential for JCS systems in the fields of ADAS and unmanned autos. Currently, the NR-V2X sidelink has been standardized by 3GPP to support low-latency high-reliability direct communication. In order to combine the benefits of both direct communication and JCS, it is promising to extend existing NR-V2X sidelink communication toward sidelink JCS. However, conflicting performance requirements arise between radar sensing accuracy and communication reliability with the limited sidelink spectrum. In order to overcome the challenges in the distributed resource allocation of sidelink JCS with a full-duplex, this paper has proposed a novel consecutive-collision mitigation semi-persistent scheduling (CCM-SPS) scheme, including the collision detection and Q-learning training stages to suppress collision probabilities. Theoretical performance analyses on Cramér–Rao Lower Bounds (CRLBs) have been made for the sensing of sidelink JCS. Key performance metrics such as CRLB, PRR and UD have been evaluated. Simulation results show the superior performance of CCM-SPS compared to similar solutions, with promising application prospects. Full article

The existence of multiple self-interference (SI) signal components, particularly the nonlinear ones, seriously constrains the performance of self-interference cancellation (SIC) methods. To decrease the complexity of SIC methods in full-duplex devices, this article proposes a power analysis method for SI signal components in a full-duplex transceiver. The proposed method comprises a separate analysis algorithm and a system-level power model. Initially, the algorithm is conducted to obtain the spectrum of the linear and nonlinear components in the power amplifier (PA) output signal. Once the linear-to-nonlinear power ratio (LNPR) has been obtained, a system-level power model is constructed by taking both the transmitter noise and analog-to-digital converter (ADC) quantization noise into account. The proposed power model allows for the allocation of SIC method performance in multiple domains during the design of full-duplex transceivers at the top level, thereby reducing the overall system complexity. The simulation results demonstrate that in a full-duplex transceiver with only antenna isolation, the power of the SI signal component is susceptible to alterations due to the operating waveform and transmission power. Finally, the accuracy of the power analysis method is verified through measurement and Simulink. Full article

In this work, we unveil the advantages of synergizing cooperative rate splitting (CRS) with user relaying and simultaneously transmitting and reflecting reconfigurable intelligent surface (STAR RIS). Specifically, we propose a novel STAR RIS-assisted CRS transmission framework, featuring six unique transmission modes that leverage various combinations of the relaying protocols (including full duplex-FD and half duplex-HD) and the STAR RIS configuration protocols (including energy splitting-ES, mode switching-MS, and time splitting-TS). With the objective of maximizing the minimum user rate, we then propose a unified successive convex approximation (SCA)-based alternative optimization (AO) algorithm to jointly optimize the transmit active beamforming, common rate allocation, STAR RIS passive beamforming, as well as time allocation (for HD or TS protocols) subject to the transmit power constraint at the base station (BS) and the law of energy conservation at the STAR RIS. To alleviate the computational burden, we further propose a low-complexity algorithm that incorporates a closed-form passive beamforming design. Numerical results show that our proposed framework significantly enhances user fairness compared with conventional CRS schemes without STAR RIS or other STAR RIS-empowered multiple access schemes. Moreover, the proposed low-complexity algorithm dramatically reduces the computational complexity while achieving very close performance to the AO method. Full article

Full-duplex relay (FDR) has attracted considerable interest in enhancing the performance of relay networks by utilizing resources more efficiently. In this paper, we propose a framework for full-duplex random relay networks (FDRRNs), where relay nodes equipped with full-duplex (FD) capability are randomly distributed within a finite two-dimensional region. We first derive the outage probability of an FDRRN and then identify the potential relay location that minimizes the outage probability. Furthermore, we introduce a low-complexity relay selection algorithm that selects the relay node nearest to the potential relay location. Finally, simulation results show that the proposed relay selection algorithm achieves performance comparable to that of the max-min relay selection algorithm. Full article

Duplex stainless-steel grade 2205 (2205 DSS) is the most widely used of the current duplex materials. The duplex steel alloy is characterized by high strength and high corrosion resistance through enhancing nitrogen and molybdenum contents. The activated tungsten inert gas (ATIG) welding technique uses the same equipment as tungsten inert gas (TIG), but prior to the welding operation, a thin layer of flux is deposited. Activation fluxes are known to influence the shape and energy characteristics of the arc. They promote the change in shapes and dimensions of the welds, namely, increasing the depth and narrowing the weld width. This work is dedicated to investigate the influence of the thermophysical properties of individual metal oxide fluxes on 2205 DSS welding morphology. It helps also to identify the recommended flux properties in order to perform full penetrated ATIG welds. Thirteen kinds of oxides (SiO₂, TiO₂, Fe₂O₃, Cr₂O₃, ZnO, Mn₂O₃, V₂O₅, MoO₃, Co₃O₄, SrO, ZrO₂, CaO, and MgO) have been tested and three current intensity levels (120, 150 and 180 A) have been considered. The results showed that the main input factors affecting the weld depth (D) were the welding current intensity with a contribution of up to 53.36%, followed by the oxides enthalpy energy with 15.05% and then by the difference between the oxides and the base metal of 2205 DSS (BM 2205 DSS) melting points with a contribution of 9.71% of the data variance. The conditions on individual oxides’ thermophysical properties to achieve full penetrated weld beads have been also revealed. Full article

In this paper, we present a novel method to enhance the sum-rate effectiveness in full-duplex unmanned aerial vehicle (UAV)-assisted communication networks. Existing approaches often couple uplink and downlink associations, resulting in suboptimal performance, particularly in dynamic environments where user demands and network conditions are unpredictable. To overcome these limitations, we propose a decoupling of uplink and downlink associations for ground-based users (GBUs), significantly improving network efficiency. We formulate a comprehensive optimization problem that integrates UAV trajectory design and user association, aiming to maximize the overall sum-rate efficiency of the network. Due to the problem’s non-convexity, we reformulate it as a Partially Observable Markov Decision Process (POMDP), enabling UAVs to make real-time decisions based on local observations without requiring complete global information. Our framework employs multi-agent deep reinforcement learning (MADRL), specifically the Multi-Agent Deep Deterministic Policy Gradient (MADDPG) algorithm, which balances centralized training with distributed execution. This allows UAVs to efficiently learn optimal user associations and trajectory controls while dynamically adapting to local conditions. The proposed solution is particularly suited for critical applications such as disaster response and search and rescue missions, highlighting the practical significance of utilizing UAVs for rapid network deployment in emergencies. By addressing the limitations of existing centralized and distributed solutions, our hybrid model combines the benefits of centralized training with the adaptability of distributed inference, ensuring optimal UAV operations in real-time scenarios. Full article

Efficient beam steerable high-gain antennas enable high-speed data rates over long-distance networks, including wireless backhaul, satellite communications (SATCOM), and SATCOM On-the-Move. These characteristics are essential for advancing contemporary wireless communication networks, particularly within 5G and beyond. Various beam steering solutions have been proposed in the literature, with passive beam steering mechanisms employing planar metasurfaces emerging as cost-effective, power-efficient, and compact options. These attributes make them well-suited for use in confined spaces, large-scale production and widespread distribution to meet the demands of the mass market. Utilizing a dual-band antenna terminal setup is often advantageous for full duplex communication in wireless systems. Therefore, this article presents a comprehensive review of the dual-band beam steering techniques for enabling full-duplex communication in modern wireless systems, highlighting their design methodologies, scanning mechanisms, physical characteristics, and constraints. Despite the advantages of planar metasurface-based beam steering solutions, the literature on dual-band beam steering antennas supporting full duplex communication is limited. This review article identifies research gaps and outlines future directions for developing economically feasible passive dual-band beam steering solutions for mass deployment. Full article

RFID (Radio Frequency Identification), which transmits control data through electronic tags in a non-contact manner, provides a new approach for efficient and low-cost remote control of oil downhole tools. However, the interference of harsh downhole environments and the high-speed movement of tags seriously affect the performance of the current downhole reader. To effectively address this issue, in this study, a novel downhole RFID reader is presented. By introducing the half-duplex communication protocol to replace the current full-duplex communication protocol in the hardware circuits of the reader, its tag recognition ability can be improved. Then, the corresponding hardware circuits and software programs are designed. Furthermore, a sparse solenoid antenna is adopted to replace the traditional tightly wound solenoid antenna, which can provide a longer reading area range to cope with the high-moving tag, and its total length and spacing parameters between adjacent coils are designed in detail. The test results show that the proposed RFID reader based on a half-duplex communication protocol can communicate with tags normally, and its sparse solenoid antenna provides significantly more tag reading times than traditional tightly wound solenoid antennas under the same antenna inductance. Full article

This paper proposes a full-duplex (FD) antenna design with passive self-interference (SI) suppression for the 28 GHz mmWave band. The reduction in SI is achieved through the design of a novel configuration of stacked Electromagnetic Band Gap structures (EBGs), which create a high impedance path to travelling electromagnetic waves between the transmit and receive antenna elements. The EBG is composed of stacked patches on layers 1 and 2 of a four-layer stack-up configuration. We present the design, optimization, and prototyping of unit antenna elements, stacked EBGs, and integration of stacked EBGs with antenna elements. We also evaluate the design through both HFSS (High Frequency Structure Simulator) and over-the-air measurements in an anechoic chamber. Through extensive evaluations, we show that (i) compared to an architecture that does not use EBGs, the proposed novel stacked EBG design provides an average of 25 dB of additional reduction in SI over 1 GHz of bandwidth, (ii) unit antenna element has over 1 GHz of bandwidth at −10 dB return loss, and (iii) HFSS simulations show close correlation with actual measurement results; however, measured results could still be several dB lower or higher than predicted simulation results. For example, the gap between simulated and measured antenna gains is less than 1 dB for 26–28 GHz and 28.5–30 GHz frequencies, but almost 3 dB for 28–28.5 GHz frequency band. Full article

The avionics network supports high-safety-level flight operations, with the analysis of transmission failures serving as a crucial means for its safety evaluation. Due to the time-dependent nature of the failure probability in avionics networks, traditional constant and unchangeable probability values can deviate from the actual situation under specific conditions. This deviation may lead to inadequate responses to occasional events and potentially cause flight accidents. A Dynamic Fault Tree (DFT) model for civil aircraft avionics network transmission failures, based on an optimized extended fuzzy algorithm, is introduced in this paper. Initially focusing on event correlations, a DFT is established for the transmission failure of the Avionics Full Duplex Switched Ethernet (AFDX). Subsequently, considering the variations between events, triangular fuzzy processing is applied to the event failure rates based on relative confidence levels. Finally, by optimizing the weakest t-norm operator, the failure probability intervals are aggregated and the fuzzy scale is regulated. Experimental results demonstrate that, compared to the static-minimum t-norm and traditional weakest t-norm methods, the proposed approach enhances the accuracy of the fuzzy failure probability intervals by 66.15% and 40.59%, respectively. Concurrently, it maintains consistency in the ranking of event importance, highlighting the superior effectiveness of the proposed method in analyzing transmission failures in avionics networks. Full article

Self-interference (SI) represents a bottleneck in the performance of full-duplex (FD) communication systems, necessitating robust offsetting techniques to unlock the potential of FD systems. Currently, deep learning has been leveraged within the communication domain to address specific challenges and enhance efficiency. Inspired by this, this paper reviews the self-interference cancellation (SIC) process in the digital domain focusing on SIC capability. The paper introduces a model architecture that integrates CNN and gated recurrent unit (GRU), while also incorporating residual networks and self-attention mechanisms to enhance the identification and elimination of SI. This model is named CGRSA-Net. Firstly, CNN is employed to capture local signal features in the time–frequency domain. Subsequently, a ResNet module is introduced to mitigate the gradient vanishing problem. Concurrently, GRU is utilized to dynamically capture and retain both long- and short-term dependencies during the communication process. Lastly, by integrating the self-attention mechanism, attention weights are flexibly assigned when processing sequence data, thereby focusing on the most important parts of the input sequence. Experimental results demonstrate that the proposed CGRSA-Net model achieves a minimum of 28% improvement in nonlinear SIC capability compared to polynomial and existing neural network-based eliminator. Additionally, through ablation experiments, we demonstrate that the various modules utilized in this paper effectively learn signal features and further enhance SIC performance. Full article