TRAXON HO Media Tube
ВСТУП
A CTiONPAD for Media Tube® HO allows users to configure and change settings easily on Media Tube® HO. Major features that can be configured include:
- Number of channels per pixel
- algorithm selection for auto control of white le D by 3-channel RGB values
Підключення
Інструменти
- e: cue Programmer (part of Lighting Application Suite, need US B dongle to use ActionPad)
- Excite+; OR
- Butler Pro DMX
Typical Connection Diagram (with Excite+)
Налаштування запису
- Please ensure the Excite+ is connected to Media Tube® HO before connecting the power supply, hot plug Excite+ may damage the device permanently.
- Please ensure that the Media Tube® HO daisy chain is the same model and does not contain any other DMX fixtures.
Read / Write Setting
Typical Connection Diagram (with Butler Pro)
Налаштування запису
- Please ensure the Butler Pro is connected to Media Tube® HO before connecting the power supply, hot plug RJ45 to Butler Pro may damage the device permanently.
- Please ensure that the Media Tube® HO daisy chain is the same model and does not contain any other DMX fixtures.
e:cue Programmer Configuartion
- U see the cue Programmer (V7.0 or higher) to open the show file.
- Go to “Application Options” under the “Extras” top menu.
- Check the “System access and application shutdown”, “Current show file modification”, “File write access” and “Enable Toaster Messages” boxes.
- Connect Excite+ or Butler Pro to PC. Device drivers will need to be installed when plug-in for the first time. Open the “Device Manager” under the view верхнє меню.
- (Excite+ only) Double-click dmxin#1 or dmxout#1 to open the “Device Properties” dialog box. Click the “Device ID” box and then the “Browse” button to select the corresponding excite+ cable to set the excite+ cables as dmxin (for Read S ettings) and dmxout (for Write S ettings).
- Make sure the setting of the dmxout device for “Output Universe DMX1” is set to 1. For Butler Pro, there will be multiple DMX channels, and all the required channels need to be set to 1. (Not all may be needed, all Media Tube® HO connected in the required channels must be the same model)
- Click the “Action Pad” button.
Конфігурація
Action Pad Overview
Модель кріплення
Set the Number of Channels per Pixel
- Users can select Media Tube® HO to run in either:
- 4 channels per pixel: Red, Green, Blue, and White channels
- 3 channels per pixel: Red, Green, and Blue channels. White LED is automatically controlled depending on the Auto White algorithm selected.
Set Auto White Mode
- When Media Tube® HO RGBW is set as 3 channels per pixel, the user can input the number to set Media Tube® HO RGBW to use one of the following modes to automatically control the brightness of white LED:
- RGB: pure 3-channels RGB, white always off and does not occupy control channels.
- Ultra Brightness: adding white without reducing the original RGB brightness, this result in high brightness output. In case Ultra-Brightness Mode is selected, the brightness of white
can be adjusted through Ultra Brightness Level. - High Efficacy: better white quality by adding white and adjusting the RGB value to maintain certain brightness, this results in better white quality.
Set Ultra-brightness Level
When Media Tube® HO RGBW is set as 3 channels per pixel and Ultra-brightness mode is in use, user can adjust the white color intensity (1-100, 100 is highest).
Налаштування приладу
Output Test Pattern
- The test pattern will be indicated on the first fixture in the pattern as follows.
Програмування
- Programming allows users to write and read settings to the Media Tube® HO.
- Please note there are the following limitations:
- Write Settings is not limited by one universe, however, the user will only receive visual confirmation for the first 512 channels.
- Read Settings can only read the parameters of the last tube of Media Tube® HO.
- Read Settings can only be done with Excite+.
Напишіть налаштування
Users can save settings into Media Tube® HO using the Write Settings button. Please note that to save settings, the user has to connect the “IN ” connector of Media Tube® HO to A ctionPad.
Once the button is pressed, the system sends the parameters. While the communication is taking place the button becomes yellow. After writing the settings the button gets
- Orange (no errors, with DMX readback over a second connection shows that Media Tube® HO reports correct settings); OR
- Red (Media Tube® HO reported other settings than desired or no read back is received).
- After writing settings to Media Tube® HO, the user needs to reset the Media Tube® HO.
Read Settings
- Users can read all existing settings inside Media Tube® HO using the Read Settings button.
- please note that to read out settings, a user has to connect the “Out” connector of Media Tube® HO to the actionpad.
- Read out setting will be displayed on the right-hand side of the screen as shown above. After reading the settings from Media Tube® HO, the user needs to reset the Media Tube® HO.
- In case the read-out setting is different from the existing setting in the user interface, the Read Settings button will be in red to notify the user of such discrepancy.
IO Devices
Connecting Status
This button displays the connecting status and allows a user to assert whether their connection bridges like Excite+ are properly connected to A ctionPad. Possible status include:
- Device Online: Excite+ / Butler Pro is correctly connected to the ActionPad.
- Device Searching: Excite+ / Butler Pro is not found.
For your safety and that of the product, please read this installation guide carefully before beginning setup and installation.
02023 TRAXON TECHNOLOGIES. ALL RIGHTS RESERVED. TRAXONT™, TX CONNECT ®, ARE TRADEMARKS OF TRAXON TECHNOLOGIES. U.S. PATENTS, E.U. PATENTS, JAPAN PATENTS,
ІНШІ ПАТЕНИ ОЧІКУЄТЬСЯ НА РОЗГЛЯД. ТЕХНІЧНІ ХАРАКТЕРИСТИКИ МОЖУТЬ ЗМІНЮВАТИСЯ БЕЗ ПОПЕРЕДЖЕННЯ. www.traxon-ecue.com
Документи / Ресурси
| TRAXON HO Media Tube [pdf] Інструкція з експлуатації AP04-16 V0.2, HO Media Tube, HO, Media Tube, Tube |
