tiba UV 511053 300x300mm Mwongozo wa Mtumiaji wa Safu ya LED ya UV

tiba UV 511053 300x300mm Mwongozo wa Mtumiaji wa Safu ya LED ya UV

Vipengele vya mtawala

• Touch screen display , simple and intuitive operation .
• Support external dry contact to control UVLED switch and alarm output (dry contact).
• Support the standard RS485 communication protocol to facilitate the communication of peripheral devices .
• Real-time monitoring of temperature , effectively protecting the stable operation of LED , and with over temperature protection and alarm function.
• Support automatic irradiation function, can count down the irradiation time, and can also recordthe total irradiation time.

Main performance and parameters of the product

Vipimo vya mtawala	384mm * 284mm * 100mm (L*W*H)
Lamp vipimo	L430 x W390 x H100mm
Ugavi wa nguvu	Single-phase AC220V 60HZ
Equipment power consumption	1000W (current 5A) Max
Emitting window	300mm*300mm
urefu wa mawimbi	365nm, 385nm, 395nm, 405nm
Nguvu ya macho	584mW/cm²
Mbinu ya baridi	air cooled
Net weight of equipment	Kilo 20
Joto la Uendeshaji	-10 ℃– 50 ℃ (non-corrosive, dust-free)
Unyevu wa mazingira ya kazi	10%–80% RH isiyopunguza

Equipment installation and connection

Muundo wa bidhaa

Kidhibiti

UV LEDLAMP

Vipimo vya Bidhaa

Ukubwa wa kidhibiti

UV LED lamp ukubwa

Schematic diagram of product installation

UV LED controller device name and function

1	UV LED connector	UV LED connection port (female)
2	Bandari ya mawasiliano ya RS485	Can be used to read and write external parameters
3	Input /Output IO terminal	Connect the foot switch or relay short circuit , switch for UV irradiation , and the alarm output signal is the relay short circuit signal . Port number: From top to bottom , a group of G1 and ON1 is short-circuited to turn on the light signal; a group of Alarm1 and Alarm1 is used for alarm output. The first group of NC and NC are the monitoring signals for the connection of the light source. Under the premise of being powered on, when the light source is connected normally, NC and NC are connected, and when the light source is disconnected, NC and NC are disconnected.
4	cable ya nguvu	Ingizo la nguvu za nje
5	swichi ya rocker	Master main power switch

Connection of UV LED light source
Align the connection port for the UV LED light source (female) on the back of the main controller with the dimpled side of the connector for the UV LED light source (male), and push the back half of the connector to insert. After insertion, it is necessary to turn the rotatable part counterclockwise until it is tightened.

Basic operation and setting of equipment

Anza na kuzima
Before starting , first check whether the UV-LED light source connection cable and power cable are connected , then turn on the power, the main power switch of the controller . When shutting down, please turn off the UV-LED light source first, then turn off the main power switch , finally unplug the power cord.

Uendeshaji wa kazi

Kiolesura kikuu	Onyesha maudhui
Mbinu ya kudhibiti	Manual control, automatic control
Irradiation method	Irradiation power and time setting, total irradiation timequery and reset
Ufuatiliaji wa joto	Set the alarm temperature and display the light source temperature in real time
Mpangilio wa mfumo	weka upya
Entering irradiation	Click the button to enter the irradiation interface
Irradiation Parameters	View parameters such as irradiation power, irradiation time, and alarm temperature

Mbinu ya kudhibiti

Hali ya udhibiti	Click switch to , clockwise work, not timing control.
	Click to switch to , the countdown works, and can be controlled regularly .

Irradiation method

Irradiation power	Click the number in the irradiation power box to pop up the input keyboard, enter the required value and click Enter to confirm . Irradiation power input range 1 -100%
Irradiation time	Click the number in the irradiation time space to pop up the input keyboard, type in the required value and click Enter to confirm . Irradiation time input range 0 – 9999 seconds
Ucheleweshaji wa mashabiki	Time setting for delaying turning off the fan after the UVLED is turned off
Total irradiation time	Record the total irradiation time of the UV lamp . You can click Clear to clear the total irradiation time . Clearing requires an administrator password .

Ufuatiliaji wa joto

Weka halijoto	Click the number in the set temperature box to pop up the inputkeyboard, enter the value you need and click Enter to confirm. The setting value range is between 0°C and 65 °C .
Ya sasa	The current temperature displays the temperature of the UV-LED light
Halijoto	source in real time. When the current temperature exceeds the set temperature, the UV-LED light source will stop working and send an alarm signal.

Mipangilio ya Mfumo

Click System Settings to enter the administrator password to enter the system settings interface.
Nenosiri la msimamizi: 123456, non-professionals do not modify parameters

Weka upya kiwandani	Click ‘restore factory settings’ to restore the original factory data: the irradiation power is 80 % , the irradiation time is 60 s , and the temperature monitoring is set to 65 ℃.
Urekebishaji wa joto	Manufacturer parameters, please do not operate!

Entering irradiation

WASHA/ZIMWA	Kitufe cha kuanza na kuacha
Rudi	Click the Return button to return to the main interface and close the irradiation at the same time.

Irradiation parameters
Click the “Irradiation Parameters” to view parameters such as irradiation power, time, and alarm temperature.
High temperature fault alarm

When the UV-LED light source is running, if the temperature of the UV-LED light source is higher than the set temperature, the UV-LED light source will automatically turn off and an alarm signal will be issued . When the  urrent temperature of the UV-LED light source is lower than the set temperature, the alarm signal will be activated. Automatically cancel.

Operesheni Example

Otomatiki hali ya udhibiti	1. Bofya, click  to switch to automatic control , and then click “Return” to return to the main interface.
Modifying Irradiation Parameters	2. Bofya to enter the parameters ,, , and click “Return” tore turn to the main interface after the setting is completed.
Entering irradiation	3. Bofya , bofya , start irradiation. The UVLED lights up and turns off automatically after a 10-second countdown, or you can click to kuzima kwa manually.
Njia ya udhibiti wa mwongozo	1. Bofya , click to switch to , and then click “Return” to return to the main interface.
Modifying Irradiation Parameters	2. Bofya to enter the parameters  ,,, and click “Return” tore turn to the main interface after the setting is completed.
into irradiation	3. Bofya , bofya, start irradiation. The UV LED lights up, counts down the timer, and click to turn it off manually.

Peripheral equipment connection

I/O signal port RS485 communication

IO signal port	Kazi
G1 NO1	Short-circuit the signal to turn on the light , and short-circuit the external relay to control the light on and off.
Alarm1, Alarm1	Alarm output signal, relay dry contact signal.
NC、NC	Light source not connected to output signal, relay dry contact signal.
RS485mawasiliano	From top to bottom A+ B- FG, used for reading and writing external parameters.

Itifaki ya mawasiliano ya RS485:
The UV LED controller uses a standard RS 485 Modbus-RTU interface, with a baud rate of 115200 , no check digit, 8 data bits, and 1 stop bit ( 115200 N 8 1).
Register description:

00	The factory default address of this machine is ‘ 0 ‘    (range: 0 -255)supports read/write
01	UVLED output power setting address     (Range: 1 -100%) supports read/write
02	Manual/automatic mode setting address (0: manual 1: automatic)supports read/write
03	Irradiation time setting address ( range: 0-9999 seconds) supports read/write
04	Alarm temperature setting address     (Setting range: 0 °C -65 °C )Support read/write
05	current temperature address read only
06	NC
07	Turn on/off UVLED address (0: off 1: on) support write

The UVLED host supports instruction codes: 

0 3	Read the function code to read the parameter as a hexadecimal number
0 6	The  parameter  written  in  the  function  code  must  be  hexadecimal number

Parameter read and write instruction format :

1. UV LED host address modification command format (hexadecimal) such as: No. 0 address changed is to No. 1 address ( after the device address is modified, the host needs to be restarted to take effect )
   

   anwani ya kifaa	nambari ya kazi	anwani ya usajili		data kidogo		Angalia CRC
   0 0	06	00	00	00	0 1	08	0B

2. UV LED host output power setting command format (hexadecimal) such as: set 50%poweroutput (decimal 50 to hexadecimal 32) if the device address is ‘ 0 ‘
   

   anwani ya kifaa	nambari ya kazi	anwani ya usajili		data kidogo		Angalia CRC
   0 0	06	00	01	00	32	59	DF

3. UV LED host automatic irradiation time setting command format (hexadecimal) suchas: set irradiation 1 0 0 seconds, that is 100 (decimal 100 is converted to hexadecimal 64) if the device address is ‘ 0 ‘
   

   anwani ya kifaa	nambari ya kazi	anwani ya usajili		data kidogo		Angalia CRC
   0 0	06	00	03	00	64	78	twenty one

4. UV LED lamp real-time temperature reading command format (hexadecimal) if the device address is ‘ 0 ‘
   

   anwani ya kifaa	nambari ya kazi	anwani ya usajili		Read the number of registers		Angalia CRC
   0 0	03	00	05	00	01	94	0B

Thamani ya kurejesha: (0 0 03 00 05 22 9A CD ) ’22’ is the real-time temperature value in hexadecimal, and 34 ℃ in decimal

Makosa ya kawaida na suluhisho

Dalili	sababu ya suala	Mbinu
kengele ya joto	Halijoto ni ya juu sana	Check whether the cooling fan is normal
	Sensor ya joto imeharibiwa	Enable backup sensor
UV-LED not bright	Kiunganishi	Check whether the connector is connected properly
no power on	Poor contact of the power cord	Check the power interface and whether the power cord plug is in good contact.
	swichi ya rocker	Is the switch on

Matengenezo ya vifaa

• Clean the surface dust every day to keep the body clean, and clean the dust of the cooling fan port regularly to keep the cooling channel normal (normally cleaned once a month, depending on the environment).
• Turn on the light to check whether the UV lamp is irradiated according to the set power, if it is abnormal, stop working, contact the staff for inspection, or contact the manufacturer.
• Equipment running for a month should be systematic maintenance, UVLED glass inspection, to see whether the pollution, UV lamp aging and other work.

Tahadhari

• Do not direct UV light to the eyes or skin, as it may cause damage .
• Do not disassemble the UV-LED irradiation may cause UV light leakage .
• When installing or removing the UV-LED irradiation head, be sure to cut off the power supply.
• When cleaning the irradiation head and controller regularly, please do not use thinner, volatileoil,acetone, kerosene, etc. You can use a soft cotton cloth to spot a small amount of ethanol andwipecarefully .
• Please use this machine in a cool, dry, ventilated environment without high magnetic field or high electric field.
• Please use the DC power supply specially provided by our factory for the power adapter.
• Do not open the controller privately to prevent the danger of electric leakage

This document is copyright@ November 01, 2024 SPDI, Inc. All rights reserved. This document is provided for information purposes only. Contents are subject to change without notice. It is not warranted to be error-free. Nor subject to any other warranties or conditions including implied warranties and conditions of merchantability or fitness for a particular purpose. 

hone: 800-977-7292
Anwani: 2801 Rosselle St Jacksonville, FL 32205
Web duka: www.cureUV.com

Nyaraka / Rasilimali

cure uv 511053 300x300mm UV LED Array [pdf] Mwongozo wa Mtumiaji 511053 300x300mm UV LED Array, 511053, 300x300mm UV LED Array, UV LED Array, LED Array, Array

Marejeleo

• Uponyaji wa UV Lamps, Balbu za UV-C Sterilizer, Mifumo ya Tiba ya Ultraviolet - CureUV
• Uponyaji wa UV Lamps, Balbu za UV-C Sterilizer, Mifumo ya Tiba ya Ultraviolet - CureUV
• Mwongozo wa Mtumiaji