Glass Panel Heater
Watch the
https://bit.ly/3zyAqu3
installation video!
Live well…
44 Glass Panel Heater
Watch the ThermoSphere Glass Panel Heater ‘How to…‘ videos!
Simply scan our QR code to see our Glass Panel Heater ‘How to…‘ video playlist.
https://bit.ly/ThermoSphereGlassPanelHeaterVideos
From how to install to creating a heating schedule, we‘ve got the videos so you can forget reading instructions and experience comfort, quicker!
Before first use
It is compulsory that you read and follow all the instructions in this manual, even if you feel you are experienced and familiar with the product.
These instructions, a copy of the purchase invoice and the original product identification labels on the product must be kept by the end user to facilitate support and warranty claims, should they be required.
IMPORTANT SAFETY INFORMATION
- Use this appliance only as described in this manual. Any other use is not recommended by the manufacturer, will void the warranty and may cause damage, fire, electric shock or injury.
- Only use this product at the stated voltage on the product identification label.
- Do not connect the appliance to the mains voltage until completely assembled.
- Always operate upright.
- Do not operate with a coiled power lead as a build up of heat is likely, which could be sufficient to become a hazard. The use of an extension cord with this appliance is not recommended.
- This appliance is intended for use in indoor domestic homes and offices or similar onlyDo not use outside.
- Adhere to the spacing and clearance requirements set out in these instructions.
- Do not cover or restrict airflow to the inlet or exhaust grilles in any manner as the appliance may overheat and become a fire risk.
- Do not place the appliance close to another heat source or cold temperature influence as this can prevent the correct operation of the heater.
- This product is NOT suitable for use on long pile carpets or rugs that could restrict air flow.
- This appliance heats up when in use and must not be touched, moved or stored until it has cooled down.
- Do not use the appliance to dry clothes.
- Do not insert any foreign object into any opening as this may cause an electric shock, fire or damage to the appliance.
- Do not operate the appliance when there is a risk of it coming into contact with water.
- Do not operate the appliance if it is damaged in any way. Seek advice from a competent and qualified electrical professional. If the product is damaged it must be fixed by a competent, qualified electrical professional.
- The most common cause of overheating is deposits of dust inside the appliance. Ensure these deposits are removed regularly by unplugging the appliance and vacuum cleaning air vents and grilles.
- Always remove plug from the mains supply before cleaning or maintenance. Do not use abrasive cleaning products on this appliance. Clean with a damp cloth (not wet) rinsed in hot soapy water only.
- Do not remove plug from the power socket until the appliance has been switched off.
- Do not allow the power cord to come into contact with the heated surfaces during operation.
- Do not run the power cord under carpet, rugs or runners etc as this can cause overheating and damage to the cable.
- Ensure the power cord does not cause a trip hazard.
- Do not twist, kink or wrap the cord around the appliance as this may cause the insulation to weaken and split.
- This appliance is not intended for use by young children or vulnerable people without competent supervision.
- Children and vulnerable people must be supervised at all times to ensure they do not touch the appliance.
- Do not modify the product in any way.
Doing so will render the warranty void and modifications are undertaken at your own risk.
Box Contents
What‘s inside your Glass Panel Heater box?
- Glass Panel Heater
- Wall fixing screws
- Wall plugs
- Aluminium feet
- Fixing screws (for feet)
- Remote control
Control Panel Display
Understand all the elements that make up your heater‘s display, control panel and remote control.
- Settings button
- Up button
- Down button
- Power button
- Heating on symbol
- Low heating indicator
- High heating indicator
- Timer indicator
- Temperature (°C) symbol
- LED temperature display
- Wi-Fi indicator
- Heating power mode
- ECO button
App Overview
Conveniently control your heating and create schedules that suit you, straight from your phone using the ThermoSphere app.
Installation
Whether you decide to mount your Glass Panel Heater to the wall or attach the provided aluminium feet, here‘s how to install it.
Wall Mounting Dimensions
| Model | Power (W) | L (mm) | H (mm) | L1 (mm) | H1 (mm) |
| TSGFR-1500 | 750/1500 | 675 | 450 | 378 | 344 |
| TSGFR-2000 | 1000/2000 | 835 | 450 | 538 | 344 |
Wall Mounting Installation
Using the wall mounting dimensions and a spirit or laser level, measure and mark the L1 size for your specific Glass Panel Heater on the wall. This varies depending on your heater size.
Drill the holes into the wall and drive the first fixing screw in place. Leave approximately 5mm of thread visible. Do this for both fixing holes.
Locate the brackets over the fixing screws and lock the heater into place.
Your heater is now securely fixed and ready to turn on.
Plug the heater in and turn on the power.
Now, turn the heater on using the switch located on the right hand side.
Important
Make sure to use suitable fixings for your wall type and ensure the wall can support the weight of your heater.
Freestanding Installation
Using a crosshead screwdriver, fit the 2 aluminium feet into position.
Ensure the feet are fully secure and then stand your panel heater up.
Plug the heater in and turn on the power.
Now, turn the heater on using the switch located on the right hand side.
Your Glass Panel Heater is now on and ready to heat!
How to use your Glass Panel Heater Display
You can always watch our ‘How to use‘ video by scanning the QR codes.
https://bit.ly/ThermoSphereGlassPanelHeaterPanel
https://bit.ly/ThermoSphereGlassPanelHeaterRemote
Turn on/off
- To turn on or off press the symbol
on the display.
Standby Mode
- Press the
Child Lock
- When your heater is on, press
and
hold both the and button at the same time for 3 seconds to lock theheater.
- ‘[ ]‘ will display, highlighting the Glass Panel Heater is locked.
- To unlock: Press
Switching from °C to °F
- Press and hold the
and
- To change back to °C or °F, simply repeat step 1.
Eco Mode
If you don‘t want to see the room temperature on the display, you can set your heater to Eco Mode.
- Using the Panel Heater, press
- To make any changes to your heater whilst in Eco Mode, simply press the display area for it to illuminate again.
- To exit Eco Mode, hold down both
Heating Power Mode
There are 2 power modes, either half or full power
The display on the panel heater will change depending on which mode it‘s in.
We recommend using full power to get your room up to temperature quickly. Once up to temperature, switch your heater to half power mode to maintain your set temperature using as little energy as possible whilst maintaining a comfortable heat.
- Using the panel heater display, press the
Setting the temperature
- Press
- Then, press
- Once you‘ve selected your desired set temperature, leave the buttons and the display temperature will revert back to the current room temperature.
- To check or change the set temperature, simply press
- For your Panel Heater to begin heating, press
will appear on the display. Your Glass Panel Heater will begin heating to reach your set temperature.
Setting a timer
By setting a timer, you can delay your heating coming on by 1-24 hours.
- To set a timer press
- Press
- When you‘ve selected the right amount of hours, leave it and it will return to the main display and the
symbol will show on the right hand side of the temperature display.
- When your timer has elapsed, you‘ll hear a short beep and your Glass Panel Heater will begin heating.
- If you want to cancel or change your timer, repeat steps 1-2. Press
How to use your Glass Panel Heater’s remote
Turn on/off
- Using the remote, press the
button
Standby Mode
- On the remote, press
Eco Mode
If you don‘t always want the temperature to show on the display, you can set your heater to Eco Mode.
- Press
and you‘ll see the display go blank. Press
Setting the temperature
- Press any button on your remote to activate the Glass Panel Heater‘s display.
- Then, press
on your remote. Your set temperature will appear on the display and flash.
- Press either
or
on your remote to increase or decrease the set temperature.
- Once you‘ve chosen your set temperature, leave the buttons on the remote and the display temperature will revert back to the current room temperature.
- To check or change the temperature you want to heat to, simply press
- For your heater to begin heating, press
. You‘ll see the
Heating Power Mode
There are 2 power modes, either half or full power . The display on the panel heater will change depending on which mode it‘s in.
We recommend using full power to get your room up to temperature quickly.
Once up to temperature, switch your heater to half power mode to maintain your set temperature using as little energy as possible whilst maintaining a comfortable heat.
- Using the remote, press
(full power) to
(half power).
Setting a timer
- Press any button on your remote to wake up your Glass Panel Heater and the display buttons will appear on the screen.
- Press
- Press
- When you‘ve selected the right amount of hours, leave your remote and the heater will return to the main display with the
- When the timer has elapsed, you‘ll hear a short beep and your Glass Panel Heater will begin heating.
- If you want to change your timer, repeat steps 2-3. To cancel your timer, set your timer to ‘0‘ or, turn your heater switch off and on again.
Setting up the ThermoSphere app
If you want to control your Glass Panel Heater via your phone, you‘ll need the
ThermoSphere app. Follow the instructions below to get set up.
App Installation
Install the ThermoSphere app. Scan the QR code below or search
‘ThermoSphere‘ in your device‘s app store.
| https://apple.co/3u6wsFn | http://bit.ly/3gITT4s |
When you‘ve downloaded the app, follow the steps to register a new account or log in if you have an existing ThermoSphere account.
- To start, press ‘Add Device‘ or if you already have other devices connected press the ‘+‘ at the top right of the screen.
- Select ‘Small Home Appliances‘ from the left hand column.
- Then select ‘Heater‘ from the options.
- Now on the Glass Panel Heater, press and hold the settings button until you hear it beep.
- When the WiFi symbol on the heater is flashing, go back to the app and select ‘Confirm indicator rapidly blink‘.
- Select your WiFi network. This may happen automatically if you‘re already connected. Once details are entered press ‘Confirm.‘
- You will see the app progressing to complete connection, this can take up to 2 minutes.
- The WiFi symbol will disappear from the heater upon successful connection and a confirmation message will appear on the app.
- You can rename your heater by pressing the pencil icon.
- If you‘ve edited the name press ‘Save‘ and then ‘Done‘. You‘ll see your heater‘s control display on the app.
Setting up a heating schedule
- Start by pressing ‘Settings‘.
- Then select ‘Schedule‘.
- Press ‘Add Schedule‘ at the bottom of your screen.
- Start by choosing the time you‘d like your heater to come ON by scrolling up or down.
- You can apply this heating event to multiple days by pressing repeat and selecting them.
- Now, press ‘Save‘ at the top right to confirm your ON times.
- To tell your heater when to switch off, press ‘Add Schedule‘.
- Press ‘Power‘, change the setting to ‘OFF‘ and press ‘Confirm‘.
- Now choose the time you‘d like your heater to turn OFF.
- Then press ‘Repeat‘ and select which other days you‘d like this off time to apply to. Press ‘Confirm‘.
- When you‘re finished, don‘t forget to press ‘Save‘ to confirm the OFF time.
- You can repeat these steps to setup a full schedule for your week.
Warranty terms & conditions
ThermoSphere Glass Panel Heaters come with a 2 year warranty.
ThermoSphere will supply a replacement product where a fault is shown to be caused by manufacture, materials or workmanship providing the goods have been installed correctly and according to installation instructions. This guarantee does not include removal, freight or installation costs.
To make a warranty claim, the customer must provide a purchase invoice or receipt.
If the product develops a fault within the warranty period due to normal wear and tear, ThermoSphere at its discretion will recognise whether it‘s a faulty product or not. If it is impossible or not economical for the manufacturer to repair the product, the manufacturer will replace the faulty product with a new unit of the same model or if there is no stock available of the same model as the product, the manufacturer will replace the product with an available equivalent product. No responsibility can be taken for altered dimensions and lining up of existing holes.
Product features and dimensions are subject to change.
Any damage caused by improper use, carelessness or incorrect wiring is not covered.
ThermoSphere is not responsible for any monetary loss or injuries caused by improper use or installation of this product.
ThermoSphere
Bridge House
Pattenden Lane
Marden
Kent
TN12 9QJ
UNITED KINGDOM
www.thermosphere.com
hello@thermosphere.com
+44 (0) 800 019 5899
Find us on LinkedIn
Search “ThermoSphere”
Check out our Youtube channel
Search “ThermoSphere underfloor heating”
Find us on Instagram
Search “ThermoSphere”
+44 (0) 800 019 5899
hello@thermosphere.com
Documents / Resources
| ThermoSphere 44 Glass Panel Heater [pdf] User Manual 44 Glass Panel Heater, 44, Glass Panel Heater, Panel Heater, Heater |