एक्ट्रोनएयर CRA100S स्प्लिट डक्टेड यूनिट
एक्ट्रोनएयर CRA100S स्प्लिट डक्टेड यूनिट
निरीक्षण
01.01. उत्पाद निरीक्षण
Check your air conditioning unit and all items against the invoice upon receiving your shipment. Inspect the unit,
components and accessories for any sign of damage. If there is any damage to the unit, contact ActronAir Customer Care
माल वापसी संख्या प्राप्त करने के लिए कृपया विभाग से तुरन्त 1300 522 722 पर संपर्क करें।
मॉडल, सीरियल नंबर, इलेक्ट्रिकल रेटेड विनिर्देशों को सत्यापित करने के लिए यूनिट नेमप्लेट की जांच करें।
01.02. कोड, विनियम और मानक
The installer and/or contractor assumes responsibility to ensure that unit installation complies with the relevant council,
state / federal codes, regulations and building code standards. All electrical wiring must be in accordance with current
electrical authority regulations and all wiring connections to be as per electrical diagram provided with the unit.
02. सामान्य जानकारी
The ActronAir Split Ducted air conditioning units are designed for applications where superior performance, high
efficiency, reliability, supply air quality and quiet operation are the prime priorities. The units are built with the latest
technology, digital compressor, EC indoor fans, low-noise outdoor fans and an intelligent electronic control.
For optimum efficiency, your air conditioning unit will deliver just the right amount of cooling or heating capacity you
demand. Even in extreme conditions, the unit will still supply the required demand at peak performance.
ऊर्जा कुशल प्रशीतन सर्किट
The ActronAir system is designed with a split ducted refrigeration circuit that delivers only the amount of cooling or
heating actually required to maintain your desired comfort at the most optimum efficiency.
प्रत्येक प्रशीतन सर्किट में निम्नलिखित शामिल होते हैं:
• High efficiency variable capacity scroll compressor with individual compressor drive.
• Hydrophilic coated condenser coil designed for optimum performance and efficiency with corrugated fins and riffled
टयूबिंग.
• Hydrophilic coated evaporator coil designed for optimum performance and efficiency with lanced fins and riffled
टयूबिंग.
बाष्पीकरण खंड
The Classic series evaporator section has EC fans which deliver the nominated airflow. The fans provide superior
performance for your comfort at optimum efficiency:
• Highly efficient EC motor that uses less energy than the traditional AC motor
• Low noise operation
कंडेनसर अनुभाग
Uses two (2) axial fans and a state of the art scroll compressor, with the following features:
• Efficient axial fans with direct drive AC motor
• Low noise operation
विद्युत अनुभाग
विद्युत खंड तत्वों से घटकों की रक्षा, नियंत्रण के लिए एक अलग पैनल से बना है।
Installation and Commissioning Guide Classic 2 Outdoor Units
Installation and Commissioning Guide – Classic 2 Split Ducted Outdoor Unit
डॉक्टर. क्रमांक 0525-073 वर्जन। 12 240708 5
टिकाऊ डिजाइन और निर्माण
ActronAir is an Australian manufacturer with proven high quality air conditioning products. Known for their durability and
reliable performance, these products are designed and built to withstand the extreme weather conditions.
The heavy gauge zinc and galvanized steel cabinet, with powder coated epoxy enamel finish, resists the toughest
conditions. The louvered outdoor coil guard protects the condenser coil from any potential damage brought by hail,
stones and other solid objects that may be projected to the unit.
Blue Epoxy Coat Coil Protection heat exchangers ensures an enhanced heat transfer with increased performance
क्षमता।
सिस्टम लचीलापन
The ActronAir air conditioning units are the first choice for residential, office, schools and other air conditioning facilities
applications, both for new construction or retrofitting projects.
रेफ्रिजरेंट हैंडलिंग और जवाबदेही
ActronAir strongly urges that all service technicians make every effort to eliminate and/or vigorously reduce the emission
of refrigerants to the atmosphere. Everyone must act in a responsible manner to conserve refrigerants.
स्थिरता और पर्यावरण के अनुकूल
The air conditioning system is supplied with zero ozone depleting R-410A refrigerant, which has no phase out or
replacement concern.
With cooling and heating performance capacity that are among the best in the market, the ActronAir air conditioning
units provide the solution for the reduction of energy consumption, CO2
emission, high fuel dependency and high
network grid demand.
सुरक्षा निर्देश
• Only licensed HVAC technicians* should install and service this air conditioning equipment. Improper service or
alteration by an unqualified technician could result in significant and major damage to the product or property which
may render your warranty null and void. Such unqualified service could also lead to severe physical injury or death.
इस साहित्य में दिए गए सभी सुरक्षा निर्देशों और उपकरण पर लगे सभी चेतावनी लेबलों का पालन करें।
• Prevailing WH&S regulations must be observed and will take precedence to the safety instructions contained on this
manual. Safe work practices and environment must be the paramount importance in the performance of all the service
प्रक्रियाएं.
• Ensure that unit installation complies with relevant council regulations and building code standards.
• All electrical wiring must be in accordance with current electrical authority regulations and all wiring connections to be
as per electrical diagram provided.
• Secure the fans against accidental contact. Beware of pinch point and sharp edges which can cause cutting injury.
• Always wear appropriate PPE, remove any dangling jewellery and protect long hair by wearing a cap.
• Make sure that safety guards and panel covers are always firmly secured and not damaged.
• This appliance is not intended for use by young children or infirm persons unless they have been adequately supervised
by a responsible person to ensure that they can use the appliance safely. Young children should be supervised to ensure
कि वे उपकरण के साथ खेलें नहीं।
• Installer must incorporate a means of electrical disconnection (isolator) in the sub mains fixed wiring in accordance
with the latest edition of the AS/NZS 3000 (also known as Australian Wiring Rules).
• Secure the power cords and control cables that goes in/out the unit. Use the cable ties provided in the control box.
*Qualifications required will be appropriate Electrical, Refrigeration and Refrigerant Handling License & Training
स्थानीय राज्य / क्षेत्र के नियमों पर निर्भर।
Installation and Commissioning Guide – Classic 2 Split Ducted Outdoor Unit
डॉक्टर। सं.0525-073 वेर. 12 240708
Installation and Commissioning Guide Classic 2 Outdoor Units
6
खतरा
खतरनाक वॉल्यूमtagई - इलेक्ट्रोक्यूशन का जोखिम।
Turn Off the power from main isolator before proceeding with any service work of the unit. Observe proper LOCK-OUT/TAGOUT (LOTO) procedures for electrical appliances in order to prevent accidental switching-on of the power supply. Extreme care
and caution must be observed should there be a need to work on live circuit.
चेतावनी
ईसी मोटर्स उच्च शक्ति कैपेसिटर से सुसज्जित हैं और इसमें खतरनाक अवशिष्ट मात्रा हो सकती हैtages at motor terminals after power has
been isolated. Wait at least 5 minutes after power isolation and test for any residual voltagई सेवा कार्य शुरू करने से पहले।
सावधानी
घूमने वाले प्रशंसकों से सावधान रहें!
उपकरण की सर्विसिंग से पहले सुनिश्चित करें कि इनडोर और आउटडोर पंखे अलग-थलग हैं और पूरी तरह से बंद हैं।
चुटकी बिंदु और तेज किनारों से सावधान रहें जो काटने की चोट का कारण बन सकते हैं। प्रशंसकों को आकस्मिक संपर्क से सुरक्षित रखें।
Always wear appropriate PPE and remove any dangling jewellery and protect long hair by wearing a cap. Ensure that no loose
clothing can be caught / entangled in moving parts.
दृश्य निरीक्षण और कार्य मूल्यांकन
Work areas and conditions must first be assessed and evaluated for any potential hazardous conditions. It is also important to be
familiar with the unit parts and components before proceeding with any service task.
04. स्थापना जानकारी
रेफ्रिजरेंट को संभालने वाले सभी सेवा तकनीशियनों को रेफ्रिजरेंट गैसों को संभालने के लिए लाइसेंस प्राप्त होना चाहिए।
रेफ्रिजरेंट को पुनर्प्राप्त और रीसायकल करें
Never release refrigerant to the atmosphere! It is an offence in Australia to do so. Always recover, recycle and reuse
refrigerants. When removing from the system, properly contain and identify refrigerants in its dedicated container for
proper disposal and/or storage. Always consider the recycle or reclaim requirements of the refrigerant before beginning
the recovery procedures. Obtain a chemical analysis of the refrigerant if necessary. For the recovered refrigerant and
acceptable refrigerant quality refer to the existing standards and regulations.
रेफ्रिजरेंट हैंडलिंग और सुरक्षा
Consult the refrigerant manufacturer’s safety data sheet (SDS) for information on proper handling and to fully understand
health, safety, storage and disposal requirements. Use the approved containment vessels and refer to appropriate safety
standards. Comply with all applicable transportation standards when shipping refrigerant containers.
सेवा उपकरण और पुनर्प्राप्ति प्रक्रिया
Always use refrigerant reclaiming equipment in order to minimise refrigerant emissions. Use equipment and methods
which will pull the lowest possible system vacuum while recovering and condensing refrigerant. Equipment capable of
pulling a vacuum of less than 500 microns is required.
Do not open the system to the atmosphere for service work until refrigerant is fully removed and/or recovered. Perform
refrigeration system evacuation, prior to charging, in accordance with AIRAH / IRHACE Refrigerant handling code of
अभ्यास।
Let the unit stand for 1 hour and with the vacuum not rising above 500 microns. A rise above 500 microns indicates a leak
from the system and a leak test is required to locate and repair any leak.
Installation and Commissioning Guide Classic 2 Outdoor Units
Installation and Commissioning Guide – Classic 2 Split Ducted Outdoor Unit
डॉक्टर. क्रमांक 0525-073 वर्जन। 12 240708 7
सावधानी
प्रशीतन प्रणाली के किसी भी मरम्मत किये जाने वाले भाग पर रिसाव परीक्षण सदैव आवश्यक होता है।
Charge refrigerant into the system only after the equipment does not leak or contain moisture. Ensure that R-410A is
only charged in liquid form. Take into consideration the correct amount of refrigerant charge specified for the system
to ensure efficient unit operations. When charging is complete, reclaim refrigerant from charging lines into an approved
refrigerant container. Seal all used refrigerant containers with approved closure devices to prevent unused refrigerant
from escaping to the atmosphere. Take extra care to maintain all service equipment directly supporting refrigerant service
work such as gauges, hoses, vacuum pumps and recycling equipment.
स्थापना तैयारी (पूर्व स्थापना विचार)
यूनिट स्थापना शुरू करने से पहले निम्नलिखित मदों पर विचार किया जाना चाहिए:
• Verify the unit capacities and ratings with the unit nameplate.
• Make certain the floor or foundation is level, solid and has sufficient structural strength to support the unit and
accessories weight.
• Install anti-vibration rubber (installer to supply) under all of the unit’s feet to help reduce noise and minimize vibration
transfer through the foundation. Ensure that all anti-vibration rubbers are rated to provide stable support without
impairing the unit’s structural integrity.
• Diameter or width of anti-vibration rubber’s must be at least equal to the width of the actual feet to prevent
deformation overtime.
• Preferably use anti-vibration rubber pads on residential units (up to 23kW split ducted).
• Allow minimum recommended clearances for periodic maintenance and service access.
• Allow sufficient space above the unit for the outdoor air discharge. Condenser air inlet, located on the coil side of the
unit, requires sufficient airflow clearance for the optimum unit performance.
• Note the conditioned supply air and return air location. Ensure sufficient spaces are allocated for these purposes.
• For the connection and location of condensate drain in the unit, refer to the drawings and dimensions section of this
नियमावली।
• Wiring connections must be in accordance with the wiring diagram provided with the unit.
• Make sure all wirings are in accordance with local electricity authority regulations and standards.
• Do not install the unit close to an area where there is a danger of fire due to volatile, explosive, flammable and/ or
खतरनाक सामग्री.
• Ensure that spaces around the unit are free from any obstructions for optimum unit performance.
• Installer to ensure correct size/type that main circuit breaker and cable is installed in unit sub-mains to protect the
sub-mains and unit wiring as per the latest edition of the AS/NZS 3000 (also known as Australian Wiring Rules).
• Installer to ensure correctly rated residual current device (RCD) is installed as per the latest edition of the
AS/NZS 3000 (also known as Australian Wiring Rules).
• Secure the power cords and control cables that goes in/out the unit. Use the cable ties provided in the control box.
नोट्स
This outdoor unit is designed to match only with ActronAir Classic Series indoor unit as specified in the Technical Selection
Catalogue.
यह इकाई केवल R-410A रेफ्रिजरेंट के साथ उपयोग के लिए डिज़ाइन की गई है।
The unit is supplied with factory charged R-410A refrigerant. Be aware of all the relevant regulations concerning the handling of
प्रशीतक।
05. ऑपरेशन मैनुअल एक्सेस
यहां से डाउनलोड करें webसाइट
ऑपरेशन मैनुअल हमारे माध्यम से डाउनलोड किया जा सकता है webनीचे दिखाया गया साइट।
https://www.actronair.com.au/brochures-manuals/#operating-manuals
Installation and Commissioning Guide – Classic 2 Split Ducted Outdoor Unit
डॉक्टर। सं.0525-073 वेर. 12 240708
Installation and Commissioning Guide Classic 2 Outdoor Units
8
अवयव खत्मview
HP CONTROL
कंप्रेसर
प्रशंसकों
कंट्रोल पैनल
तार
विधानसभा
स्राव होना
गुलबंद
LP CONTROL
REVERSING
वाल्व
संचायक
Installation and Commissioning Guide Classic 2 Outdoor Units
Installation and Commissioning Guide – Classic 2 Split Ducted Outdoor Unit
डॉक्टर. क्रमांक 0525-073 वर्जन। 12 240708 9
07. नियंत्रण कक्ष
07.01. Single Phase (10-17kW)
24VAC RELAY
(Add On Cooling
for CCA models only)
शुरू
CAPACITOR RUN CAPACITOR
सिंगल फेज़
सॉफ्ट स्टार्टर
कंप्रेसर
सिरीय पिंडक
मुख्य
टर्मिनल
अवरोध पैदा करना
पंखे की गति
संधारित्र
CONTROL BOARD CONTROL
परिपथ वियोजक
पंखा चलाना
संधारित्र
07.02. Three Phase (13-23 kW)
पंखे की गति
संधारित्र
कंप्रेसर
contactor
नियंत्रण समिति
नियंत्रण
परिपथ वियोजक
24VAC RELAY
(Add On Cooling
for CCA models only)
पंखा चलाना
संधारित्र
SUB-MAINS
सिरीय पिंडक
Installation and Commissioning Guide – Classic 2 Split Ducted Outdoor Unit
डॉक्टर। सं.0525-073 वेर. 12 240708
Installation and Commissioning Guide Classic 2 Outdoor Units
10
07.03. Three Phase – Soft Starter Option (13-23 kW)
3 चरण
सॉफ्ट स्टार्टर
पंखे की गति
संधारित्र
नियंत्रण समिति
नियंत्रण
परिपथ वियोजक
24VAC RELAY
(Add On Cooling
for CCA models only)
पंखा चलाना
संधारित्र
SUB-MAINS
सिरीय पिंडक
Installation and Commissioning Guide Classic 2 Outdoor Units
Installation and Commissioning Guide – Classic 2 Split Ducted Outdoor Unit
डॉक्टर. क्रमांक 0525-073 वर्जन। 12 240708 11
इकाई आयाम और मंजूरी
08.01. CRA100S
यूनिट मॉडल
संख्या
इकाई वजन
(किलोग्राम)
CORNER WEIGHTS (kg)
ए बी सी डी
CRA100S 121 14 45 22 40
टिप्पणियाँ:
1. Do not scale drawing. All dimensions are in mm unless specified. Refer to
corresponding unit dimensional drawing for mounting hole details.
2. Service Access Areas and Spaces for Airflow Clearances given above are
suggested minimum based on the condition that the spaces around the
units are free from any obstructions and a walkway passage of 1000mm
between the units or between the unit and the outside perimeter is
उपलब्ध।
3. Minimum service access areas and spaces for airflow clearances are
responsibilities of the installer, ActronAir will not be held liable for any
वायु प्रवाह के लिए पहुंच और स्थान की कमी के कारण अतिरिक्त शुल्क लगता है।
4. Under all circumstances, condenser air must not recirculate back onto
condenser coil. Keep all clearance free of any obstructions.
5. Maximum External Static of Outdoor Fans is 5 Pa.
6. STACKING OF UNITS: Ensure that minimum airflow and clearances are met.
7. Refer to pipe Connection Details on Specifications Sheet.
8. एमटीजी सीसी डिस्ट = माउंटिंग सेंटर से सेंटर दूरी।
9. पैर माउंट करने के लिए M12 बोल्ट का उपयोग करें।
तीसरा कोण
प्रक्षेपण
B
MINIMUM SERVICE ACCESS AREAS
AND AIRFLOW CLEARANCES
300 मिमी
सेवा
निकासी
600 मिमी
सेवा
निकासी
(कंप्रेसर
और
ELECTRICALS) OUTDOOR COIL
कंप्यूटर अनुप्रयोग
A NIL – TO – MINIMUM SERVICE CLEARANCE
C
300 मिमी
SERVICE / AIRFLOW CLEARANCE
D
ऊंचाई निकासी
= 1500 मिमी
आउटडोर कुंडल
565
1245 ओ/ए
255 २०
45
880
35
25
(MTG C-C DIST) 930
100 115 815
57.5
115
57.5
940
हे / A
535
हे / A
230
कंप्यूटर अनुप्रयोग
470
(एमटीजी सीसी डिस्ट)
25 २०
85
OUTDOOR AIR INLET
आउटडोर
हवा का प्रवेश मार्ग
आउटडोर
हवा की दुकान
ELECT. ACCESS
2 x Ø 25.4 mm (1″)
गैस पाईप
Ø 19.05 मिमी (3/4″)
CUT SWAGE
IN FIELD
तरल पाइप
Ø 9.52 मिमी (3/8″)
स्वैग्ड
वाष्पीकरण
अंक
शीर्ष VIEW
ओर VIEW सामने VIEW
** चित्र बिना सूचना के परिवर्तन के अधीन है **
CONDENSATION POINTS ARE DESIGNED TO ENSURE ALL
CONDENSATION IS REMOVED EFFICIENTLY TO AVOID
WATER POOLING WITHIN THE CONDENSER. IF A SINGLE
CONDENSATION DRAIN POINT IS REQUIRED, ACTRONAIR
RECOMMENDS THE INSTALLATION OF A CONDENSER TRAY.
THESE ARE AVAILABLE AS AN ADDITIONAL ACCESSORY.
Installation and Commissioning Guide – Classic 2 Split Ducted Outdoor Unit
डॉक्टर। सं.0525-073 वेर. 12 240708
Installation and Commissioning Guide Classic 2 Outdoor Units
12
08.02. CRA130S / CRA130T / CCA130S
यूनिट मॉडल
संख्या
इकाई वजन
(किलोग्राम)
CORNER WEIGHTS (kg)
ए बी सी डी
CRA130S / CCA130S 132 21 42 19 50
CRA130T 130 21 40 19 50
** चित्र बिना सूचना के परिवर्तन के अधीन है **
CONDENSATION POINTS ARE DESIGNED TO ENSURE ALL
CONDENSATION IS REMOVED EFFICIENTLY TO AVOID
WATER POOLING WITHIN THE CONDENSER. IF A SINGLE
CONDENSATION DRAIN POINT IS REQUIRED, ACTRONAIR
RECOMMENDS THE INSTALLATION OF A CONDENSER TRAY.
THESE ARE AVAILABLE AS AN ADDITIONAL ACCESSORY.
1320 ओ/ए
255 २०
255
580
हे / A
550
कंप्यूटर अनुप्रयोग
65
आउटडोर कुंडल
OUTDOOR AIR INLET
आउटडोर
हवा की दुकान
990
हे / A
आउटडोर
हवा का प्रवेश मार्ग
925
35
30
110 115 870
57.5
115
57.5
25 25 517
(MTG C-C DIST) 985
(एमटीजी सीसी डिस्ट)
वाष्पीकरण
अंक
वाष्पीकरण
अंक
ओर VIEW सामने VIEW
शीर्ष VIEW
टिप्पणियाँ:
1. Do not scale drawing. All dimensions are in mm unless specified. Refer to
corresponding unit dimensional drawing for mounting hole details.
2. Service Access Areas and Spaces for Airflow Clearances given above are
suggested minimum based on the condition that the spaces around the
units are free from any obstructions and a walkway passage of 1000mm
between the units or between the unit and the outside perimeter is
उपलब्ध।
3. Minimum service access areas and spaces for airflow clearances are
responsibilities of the installer, ActronAir will not be held liable for any
वायु प्रवाह के लिए पहुंच और स्थान की कमी के कारण अतिरिक्त शुल्क लगता है।
4. Under all circumstances, condenser air must not recirculate back onto
condenser coil. Keep all clearance free of any obstructions.
5. Maximum External Static of Outdoor Fans is 5 Pa.
6. STACKING OF UNITS: Ensure that minimum airflow and clearances are met.
7. Refer to pipe Connection Details on Specifications Sheet.
8. एमटीजी सीसी डिस्ट = माउंटिंग सेंटर से सेंटर दूरी।
9. पैर माउंट करने के लिए M12 बोल्ट का उपयोग करें।
तीसरा कोण
प्रक्षेपण
MINIMUM SERVICE ACCESS AREAS
AND AIRFLOW CLEARANCES
300 मिमी
सेवा
निकासी
600 मिमी
सेवा
निकासी
(कंप्रेसर
और
ELECTRICALS) OUTDOOR COIL
कंप्यूटर अनुप्रयोग
A NIL – TO – MINIMUM SERVICE CLEARANCE
C
B
400 मिमी
SERVICE / AIRFLOW CLEARANCE
D
ऊंचाई निकासी
= 1500 मिमी
Installation and Commissioning Guide Classic 2 Outdoor Units
Installation and Commissioning Guide – Classic 2 Split Ducted Outdoor Unit
डॉक्टर. क्रमांक 0525-073 वर्जन। 12 240708 13
08.03. CRA150S / CRA150T / CCA150S
यूनिट मॉडल
संख्या
इकाई वजन
(किलोग्राम)
CORNER WEIGHTS (kg)
ए बी सी डी
CRA150S / CCA150S 133 19 45 22 47
CRA150T 132 20 43 21 48
** चित्र बिना सूचना के परिवर्तन के अधीन है **
CONDENSATION POINTS ARE DESIGNED TO ENSURE ALL
CONDENSATION IS REMOVED EFFICIENTLY TO AVOID
WATER POOLING WITHIN THE CONDENSER. IF A SINGLE
CONDENSATION DRAIN POINT IS REQUIRED, ACTRONAIR
RECOMMENDS THE INSTALLATION OF A CONDENSER TRAY.
THESE ARE AVAILABLE AS AN ADDITIONAL ACCESSORY.
1320 ओ/ए
255 २०
255
580
हे / A
550
कंप्यूटर अनुप्रयोग
65
आउटडोर कुंडल
OUTDOOR AIR INLET
आउटडोर
हवा की दुकान
990
हे / A
आउटडोर
हवा का प्रवेश मार्ग
925
35
30
110 115 870
57.5
115
57.5
25 25 517
(MTG C-C DIST) 985
(एमटीजी सीसी डिस्ट)
वाष्पीकरण
अंक
वाष्पीकरण
अंक
शीर्ष VIEW
ओर VIEW सामने VIEW
टिप्पणियाँ:
1. Do not scale drawing. All dimensions are in mm unless specified. Refer to
corresponding unit dimensional drawing for mounting hole details.
2. Service Access Areas and Spaces for Airflow Clearances given above are
suggested minimum based on the condition that the spaces around the
units are free from any obstructions and a walkway passage of 1000mm
between the units or between the unit and the outside perimeter is
उपलब्ध।
3. Minimum service access areas and spaces for airflow clearances are
responsibilities of the installer, ActronAir will not be held liable for any
वायु प्रवाह के लिए पहुंच और स्थान की कमी के कारण अतिरिक्त शुल्क लगता है।
4. Under all circumstances, condenser air must not recirculate back onto
condenser coil. Keep all clearance free of any obstructions.
5. Maximum External Static of Outdoor Fans is 5 Pa.
6. STACKING OF UNITS: Ensure that minimum airflow and clearances are met.
7. Refer to pipe Connection Details on Specifications Sheet.
8. एमटीजी सीसी डिस्ट = माउंटिंग सेंटर से सेंटर दूरी।
9. पैर माउंट करने के लिए M12 बोल्ट का उपयोग करें।
तीसरा कोण
प्रक्षेपण
ऊंचाई निकासी
= 1500 मिमी
B
MINIMUM SERVICE ACCESS AREAS
AND AIRFLOW CLEARANCES
300 मिमी
सेवा
निकासी
600 मिमी
सेवा
निकासी
(कंप्रेसर
और
ELECTRICALS) OUTDOOR COIL
कंप्यूटर अनुप्रयोग
A NIL – TO – MINIMUM SERVICE CLEARANCE
C
400 मिमी
SERVICE / AIRFLOW CLEARANCE
D
Installation and Commissioning Guide – Classic 2 Split Ducted Outdoor Unit
डॉक्टर। सं.0525-073 वेर. 12 240708
Installation and Commissioning Guide Classic 2 Outdoor Units
14
08.04. CRA170S / CRA170T / CCA170S / CCA170T
यूनिट मॉडल
संख्या
इकाई वजन
(किलोग्राम)
CORNER WEIGHTS (kg)
ए बी सी डी
CRA170S / CCA170S 156 17 54 28 57
CRA170T / CCA170T 155 17 54 28 56
** चित्र बिना सूचना के परिवर्तन के अधीन है **
CONDENSATION POINTS ARE DESIGNED TO ENSURE ALL
CONDENSATION IS REMOVED EFFICIENTLY TO AVOID
WATER POOLING WITHIN THE CONDENSER. IF A SINGLE
CONDENSATION DRAIN POINT IS REQUIRED, ACTRONAIR
RECOMMENDS THE INSTALLATION OF A CONDENSER TRAY.
THESE ARE AVAILABLE AS AN ADDITIONAL ACCESSORY.
1460 ओ/ए
340
580
हे / A
255
कंप्यूटर अनुप्रयोग
आउटडोर कुंडल
1045
हे / A
110 115 1010 25 25
60
57.5
115
57.5
555
35
30
110
OUTDOOR AIR INLET
आउटडोर
हवा का प्रवेश मार्ग
आउटडोर
हवा की दुकान
980
1125
(एमटीजी सीसी डिस्ट)
517
(एमटीजी सीसी डिस्ट)
500
शीर्ष VIEW
ओर VIEW सामने VIEW
टिप्पणियाँ:
1. Do not scale drawing. All dimensions are in mm unless specified. Refer to
corresponding unit dimensional drawing for mounting hole details.
2. Service Access Areas and Spaces for Airflow Clearances given above are
suggested minimum based on the condition that the spaces around the
units are free from any obstructions and a walkway passage of 1000mm
between the units or between the unit and the outside perimeter is
उपलब्ध।
3. Minimum service access areas and spaces for airflow clearances are
responsibilities of the installer, ActronAir will not be held liable for any
वायु प्रवाह के लिए पहुंच और स्थान की कमी के कारण अतिरिक्त शुल्क लगता है।
4. Under all circumstances, condenser air must not recirculate back onto
condenser coil. Keep all clearance free of any obstructions.
5. Maximum External Static of Outdoor Fans is 5 Pa.
6. STACKING OF UNITS: Ensure that minimum airflow and clearances are met.
7. Refer to pipe Connection Details on Specifications Sheet.
8. एमटीजी सीसी डिस्ट = माउंटिंग सेंटर से सेंटर दूरी।
9. पैर माउंट करने के लिए M12 बोल्ट का उपयोग करें।
तीसरा कोण
प्रक्षेपण
ऊंचाई निकासी
= 1500 मिमी
B
MINIMUM SERVICE ACCESS AREAS
AND AIRFLOW CLEARANCES
300 मिमी
सेवा
निकासी
600 मिमी
सेवा
निकासी
(कंप्रेसर
और
ELECTRICALS) OUTDOOR COIL
कंप्यूटर अनुप्रयोग
A NIL – TO – MINIMUM SERVICE CLEARANCE
C
400 मिमी
SERVICE / AIRFLOW CLEARANCE
D
Installation and Commissioning Guide Classic 2 Outdoor Units
Installation and Commissioning Guide – Classic 2 Split Ducted Outdoor Unit
डॉक्टर. क्रमांक 0525-073 वर्जन। 12 240708 15
08.05. CRA200T / CCA200T
यूनिट मॉडल
संख्या
इकाई वजन
(किलोग्राम)
CORNER WEIGHTS (kg)
ए बी सी डी
CRA200T / CCA200T 158 15 59 38 46
1460 ओ/ए
340
580
हे / A
255
कंप्यूटर अनुप्रयोग
आउटडोर कुंडल
1045
हे / A
110 115 1010 25 25
60
57.5
115
57.5
555
35
30
110
OUTDOOR AIR INLET
आउटडोर
हवा का प्रवेश मार्ग
आउटडोर
हवा की दुकान
980
1125
(एमटीजी सीसी डिस्ट)
517
(एमटीजी सीसी डिस्ट)
500
आउटडोर
हवा का प्रवेश मार्ग
ओर VIEW सामने VIEW
शीर्ष VIEW
** चित्र बिना सूचना के परिवर्तन के अधीन है **
CONDENSATION POINTS ARE DESIGNED TO ENSURE
ALL CONDENSATION IS REMOVED EFFICIENTLY TO
AVOID WATER POOLING WITHIN THE CONDENSER.
IF A SINGLE CONDENSATION DRAIN POINT IS
REQUIRED, ACTRONAIR RECOMMENDS THE
INSTALLATION OF A CONDENSER TRAY. THESE ARE
AVAILABLE AS AN ADDITIONAL ACCESSORY.
टिप्पणियाँ:
1. Do not scale drawing. All dimensions are in mm unless specified. Refer to
corresponding unit dimensional drawing for mounting hole details.
2. Service Access Areas and Spaces for Airflow Clearances given above are
suggested minimum based on the condition that the spaces around the
units are free from any obstructions and a walkway passage of 1000mm
between the units or between the unit and the outside perimeter is
उपलब्ध।
3. Minimum service access areas and spaces for airflow clearances are
responsibilities of the installer, ActronAir will not be held liable for any
वायु प्रवाह के लिए पहुंच और स्थान की कमी के कारण अतिरिक्त शुल्क लगता है।
4. Under all circumstances, condenser air must not recirculate back onto
condenser coil. Keep all clearance free of any obstructions.
5. Maximum External Static of Outdoor Fans is 5 Pa.
6. STACKING OF UNITS: Ensure that minimum airflow and clearances are met.
7. Refer to pipe Connection Details on Specifications Sheet.
8. एमटीजी सीसी डिस्ट = माउंटिंग सेंटर से सेंटर दूरी।
9. पैर माउंट करने के लिए M12 बोल्ट का उपयोग करें।
तीसरा कोण
प्रक्षेपण
B
MINIMUM SERVICE ACCESS AREAS
AND AIRFLOW CLEARANCES
300 मिमी
सेवा /
वायु प्रवाह
निकासी
600 मिमी
सेवा
निकासी
(कंप्रेसर
और
इलेक्ट्रिकल्स)
A NIL – TO – MINIMUM SERVICE CLEARANCE
C
400 मिमी
SERVICE / AIRFLOW CLEARANCE
D
ऊंचाई निकासी
= 1500 मिमी
Installation and Commissioning Guide – Classic 2 Split Ducted Outdoor Unit
डॉक्टर। सं.0525-073 वेर. 12 240708
Installation and Commissioning Guide Classic 2 Outdoor Units
16
08.06. CRA230T / CCA230T
यूनिट मॉडल
संख्या
इकाई वजन
(किलोग्राम)
WEIGHT DISTRIBUTION (kg)
ए बी सी डी
CRA230T / CCA230T 195 30 57 41 67
1685 ओ/ए
380 २०
685
हे / A
कंप्यूटर अनुप्रयोग
आउटडोर कुंडल
OUTDOOR AIR INLET
आउटडोर
हवा का प्रवेश मार्ग
295
125
673.5
(एमटीजी सीसी डिस्ट)
110 118 555.5
59 २०
1105
हे / A
670
118 555.5 118
673.5
(एमटीजी सीसी डिस्ट)
60
25 २०
आउटडोर
हवा की दुकान
आउटडोर
हवा का प्रवेश मार्ग
1025
50
30
616
(एमटीजी सीसी डिस्ट)
गैस पाईप
Ø 28.6 mm (1-1/8″)
ELECT. ACCESS
2 x Ø 25.4 mm (1″)
तरल पाइप
Ø 12.7 mm (1/2″) SWAGED
संघनन
अंक
संघनन
अंक
ओर VIEW सामने VIEW
शीर्ष VIEW
** चित्र बिना सूचना के परिवर्तन के अधीन है **
CONDENSATION POINTS ARE DESIGNED TO ENSURE
ALL CONDENSATION IS REMOVED EFFICIENTLY TO
AVOID WATER POOLING WITHIN THE CONDENSER.
IF A SINGLE CONDENSATION DRAIN POINT IS
REQUIRED, ACTRONAIR RECOMMENDS THE
INSTALLATION OF A CONDENSER TRAY. THESE ARE
AVAILABLE AS AN ADDITIONAL ACCESSORY.
टिप्पणियाँ:
1. Do not scale drawing. All dimensions are in mm unless specified. Refer to
corresponding unit dimensional drawing for mounting hole details.
2. Service Access Areas and Spaces for Airflow Clearances given above are
suggested minimum based on the condition that the spaces around the
units are free from any obstructions and a walkway passage of 1000mm
between the units or between the unit and the outside perimeter is
उपलब्ध।
3. Minimum service access areas and spaces for airflow clearances are
responsibilities of the installer, ActronAir will not be held liable for any
वायु प्रवाह के लिए पहुंच और स्थान की कमी के कारण अतिरिक्त शुल्क लगता है।
4. Under all circumstances, condenser air must not recirculate back onto
condenser coil. Keep all clearance free of any obstructions.
5. Maximum External Static of Outdoor Fans is 5 Pa.
6. STACKING OF UNITS: Ensure that minimum airflow and clearances are met.
7. Refer to pipe Connection Details on Specifications Sheet.
8. एमटीजी सीसी डिस्ट = माउंटिंग सेंटर से सेंटर दूरी।
9. पैर माउंट करने के लिए M12 बोल्ट का उपयोग करें।
तीसरा कोण
प्रक्षेपण
ऊंचाई निकासी
= 1500 मिमी
B
MINIMUM SERVICE ACCESS AREAS
AND AIRFLOW CLEARANCES
300 मिमी
सेवा /
वायु प्रवाह
निकासी
800 मिमी
सेवा
निकासी
(कंप्रेसर
और
इलेक्ट्रिकल्स)
A NIL – TO – MINIMUM SERVICE CLEARANCE
C
600 मिमी
SERVICE / AIRFLOW CLEARANCE
D
Installation and Commissioning Guide Classic 2 Outdoor Units
Installation and Commissioning Guide – Classic 2 Split Ducted Outdoor Unit
डॉक्टर. क्रमांक 0525-073 वर्जन। 12 240708 17
09. यूनिट उठाने की प्रक्रिया
चेतावनी
WH&S विनियमों का पालन किया जाना चाहिए तथा उठाने की प्रक्रिया के दौरान इन्हें प्राथमिकता दी जाएगी।
क्रेन उठाने की विधि
ऊंची इमारतों को उठाने के लिए क्रेन लिफ्टिंग विधि की सिफारिश की जाती है।
एक चित्र 1
फैलानेवाला
छड़
Provide rubber
pads between the
spreader bar and
unit to prevent
damage to the unit
विवरण ए
आउटडोर
इकाई
Slip nylon slings
through the pallet
लूप के सिरों को जोड़ें
गोफन को बेड़ियों में जकड़ना
क्रेन उठाने के लिए आवश्यक उपकरण:
• 1 Shackle
• 2 x Nylon Slings
• Spreader bars
बेड़ियों और स्लिंग्स का चयन करने से पहले इकाई वजन के लिए कैटलॉग देखें।
टिप्पणी
शैकल और स्लिंग का चयन करने से पहले इकाई भार के लिए इकाई आयाम और क्लीयरेंस अनुभाग देखें।
प्रक्रिया:
1. Slip nylon slings through the pallet as shown in Fig. 1.
2. Use a Bow or Dee shackle to connect the slings.
3. Ensure slings are protected by rubber pads or similar if slings are draped across unit edges, corners, or air grilles .
इससे इकाई को उठाने के दौरान क्षतिग्रस्त होने से बचाया जा सकेगा।
4. SPREADER BARS must be used when lifting the unit.
5. Test lift the unit to determine exact unit balance and stability before hoisting it to the installation location.
Installation and Commissioning Guide – Classic 2 Split Ducted Outdoor Unit
डॉक्टर। सं.0525-073 वेर. 12 240708
Installation and Commissioning Guide Classic 2 Outdoor Units
18
कांटा लिफ्ट विधि
खतरा
Make sure rigging equipment, accessories and plant are sufficiently and safely capable to lift the unit in order to prevent
potential damage to property, severe personal injury or death. Please check unit weight and weight distribution points as
shown in the unit drawing dimensions section.
प्रक्रिया:
1. To move the unit around with a forklift, insert the fork tines through the pallet, as shown in Fig. 2.
2. Only fork the unit through compressor end or side of the unit. (See illustration for location of compressor end)
चित्र .2
INSERT FORKLIFT
यहाँ टाइन
कंप्रेसर
अंत
सावधानी
DO NOT LIFT UNIT
at this end.
X
सावधानी
यूनिट को सुरक्षित रूप से ले जाने के लिए फोर्क लिफ्ट टाइन की लंबाई यूनिट के मध्य भाग से गुजरनी चाहिए।
Installation and Commissioning Guide Classic 2 Outdoor Units
Installation and Commissioning Guide – Classic 2 Split Ducted Outdoor Unit
डॉक्टर. क्रमांक 0525-073 वर्जन। 12 240708 19
10. आउटडोर यूनिट की तैयारी
पहुँच
पैनल
आउटडोर
इकाई
बढ़ते
शिकंजा
1. Remove mounting screws, as shown below:
2. Remove Access Panel.
• Remove Access Panel-Electrical as illustrated below:
A
निष्कासन आदेश:
Pull-Out 20mm
Pull-Down to remove
एक्सेस पैनल-इलेक्ट्रिकल
A
B
B
एक्सेस पैनल
निकालना
पैनल का उपयोग
3. Install Interconnecting Field Pipes
• Braze refrigeration piping. Refer to Section 10 for details of field pipe sizes and piping installation procedure.
चेतावनी
Live electrical within enclosure. Isolate electrical supply before
removing panels. Authorised technicians access only
Installation and Commissioning Guide – Classic 2 Split Ducted Outdoor Unit
डॉक्टर। सं.0525-073 वेर. 12 240708
Installation and Commissioning Guide Classic 2 Outdoor Units
20
11. फील्ड पाइप कनेक्शन
11.01. पाइपिंग और ब्रेज़िंग
सावधानी
The units described in this guide use R-410A refrigerant
R-410A operates at a pressure approximately 1.6 times higher than similar systems using R-22. When installing equipment
using R-410A refrigerant, there are number of standards that must be met:
• The system of this unit operates with Polyolester (POE) oil that rapidly absorbs moisture.
• The maximum time any system can be opened to atmosphere is 15 minutes.
• It is important to work with absolute cleanliness.
• Brazing must be done with the use of Nitrogen to avoid carbon deposits into the pipes.
• The system must be evacuated thoroughly to 500 microns (see evacuation procedure).
• The system must always be charged with R-410A refrigerant in liquid state.
• Never allow R-410A refrigerant to vent into the atmosphere. It is an offence to release refrigerant in Australia.
• Always reclaim refrigerant using equipment and container dedicated for R-410A system use only.
• Only qualified technicians are allowed to perform any work described in this guide.
• All work must be carried out in accordance with Australia and New Zealand refrigerant handling code of practice.
Maximum allowable total equivalent field pipe length is 60 metres, see diagram below. This includes all the equivalent pipe
fitting loses and vertical height difference. Vertical height difference must not exceed 20 metres. Table 1 below shows the
equivalent straight pipe length of elbow fittings.
तालिका 1: कोहनी फिटिंग की समतुल्य सीधी पाइप लंबाई (मीटर में)
Pipe size Nominal
व्यास
90 डिग्री
Long Radius
कोहनी
90 डिग्री
Short Radius
कोहनी
45 डिग्री
Long Radius
कोहनी
45 डिग्री
Short Radius
कोहनी
9.52 (3/8”) 0.24 0.36 0.09 0.14
15.88 (5/8”) 0.30 0.45 0.15 0.23
19.05 (3/4”) 0.40 0.60 0.18 0.27
22.22 (7/8”) 0.46 0.69 0.21 0.32
25.4 (1”) 0.52 0.78 0.24 0.36
28.58 (1-1/8”) 0.55 0.83 0.27 0.41
Selected field pipe sizes must match the recommended sizes in table above. If the installation requires different field pipe
diameter due to different application condition other than recommended, contact ActronAir for advice.
अधिकांश यूनिट पाइप कनेक्शन फैक्ट्री में स्वैज किए जाते हैं, ताकि उन्हें अनुशंसित फील्ड पाइप व्यास में आसानी से फिट किया जा सके।
When it is required to install other refrigeration devices, such as refrigerant drier, solenoid valve and the like, include the
equivalent straight pipe length of the device in the calculation of total equivalent field pipe length.
Installation and Commissioning Guide Classic 2 Outdoor Units
Installation and Commissioning Guide – Classic 2 Split Ducted Outdoor Unit
डॉक्टर. क्रमांक 0525-073 वर्जन। 12 240708 21
दोनों पाइपों को इंसुलेट किया जाना आवश्यक है।
Improper insulation can result in condensation forming on the pipework’s surface, potentially leading to dripping
वाष्पीकरण
A = EQUIVALENT PIPE LENGTH,
60 मीटर (अधिकतम)
B = VERTICAL HEIGHT,
20 मीटर (अधिकतम)
B
आउटडोर यूनिट
A
FIELD PIPE
(Installer to Supply)
इनडोर यूनिट
Exampकुल समतुल्य क्षेत्र पाइप लंबाई गणना का प्रकार
सावधानी
उपरोक्त चित्रण गणना उदाहरण के रूप में दिखाया गया हैamples only. It
is the responsibility of the Installer to design an efficient
refrigeration piping lay out for optimum unit performance.
E1
आउटडोर
UNIT E2
V1
H1
H2
इनडोर
इकाई
E3
V2
H3
E4
समतुल्य पाइप लंबाई = कुल क्षैतिज लंबाई + कुल ऊर्ध्वाधर लंबाई
+ कोहनी से कुल नुकसान
कहाँ:
H = क्षैतिज लंबाई
V = ऊर्ध्वाधर लंबाई
E = कोहनी हानियाँ
Equivalent Pipe Length = (H1
+ H2
+ H3
) + (V1
+ वी०
) + (E1
+ ई2
+ ई3
+ ई4
)
Installation and Commissioning Guide – Classic 2 Split Ducted Outdoor Unit
डॉक्टर। सं.0525-073 वेर. 12 240708
Installation and Commissioning Guide Classic 2 Outdoor Units
22
TABLE 2: REFRIGERATION PIPING – SINGLE PHASE
Reverse Cycle (Outdoor / Indoor) CRA100S /
ईवीए100एस
CRA130S /
ईवीए130एस
CRA150S /
ईवीए150एस
CRA170S /
ईवीए170एस
Add On Cooling (Outdoor / Indoor) – CCA130S /
ईएए130एस
CCA150S /
ईएए150एस
CCA170S /
ईएए170एस
Max. Equivalent Pipe Length Range metres 0 – 60 0 – 60 0 – 60 0 – 60
Max. Vertical Height Differential (1) metres 20 20 20 2 0
फ़ील्ड पाइप आकार
Liquid Line mm (inch) 3/8 (9.52) 3/8 (9.52) 3/8 (9.52) 3/8 (9.52)
Gas Line mm (inch) 5/8 (15.88) 3/4 (19.05) 3/4 (19.05) 3/4 (19.05)
आउटडोर पाइप का आकार
Liquid Line mm (inch) 3/8 (9.52)
स्वैग
3/8 (9.52)
स्वैग
3/8 (9.52)
स्वैग
3/8 (9.52)
स्वैग
Gas Line mm (inch) 3/4 (19.05)
swaged (2)
3/4 (19.05)
स्वैग
3/4 (19.05)
स्वैग
3/4 (19.05)
स्वैग
इनडोर पाइप का आकार
Liquid Line mm (inch) 3/8 (9.52)
स्वैग
3/8 (9.52)
स्वैग
3/8 (9.52)
स्वैग
3/8 (9.52)
स्वैग
Gas Line mm (inch) 5/8 (15.88)
स्वैग
3/4 (19.05)
स्वैग
3/4 (19.05)
स्वैग
3/4 (19.05)
स्वैग
नोट्स
(1) अधिकतम क्षेत्र पाइप लंबाई में शामिल.
(2) Cut Swaged End on the unit to fit field pipe.
TABLE 3: REFRIGERATION PIPING – THREE PHASE
Reverse Cycle (Outdoor / Indoor) CRA130T /
ईवीए130एस
CRA150T /
ईवीए150एस
CRA170T /
ईवीए170एस
CRA200T /
ईवीए200एस
CRA230T /
ईवीए230एस
Add On Cooling (Outdoor / Indoor) – – CCA170T /
ईएए170एस
CCA200T /
ईएए200एस
CCA230T /
ईएए230एस
Max. Equivalent Pipe Length Range metres 0 – 60 0 – 60 0 – 60 0 – 60 0 – 60
Max. Vertical Height Differential (1) metres 20 20 20 20 20
फ़ील्ड पाइप आकार
Liquid Line mm (inch) 3/8 (9.52) 3/8 (9.52) 3/8 (9.52) 1/2 (12.7) (2) 1/2 (12.7)
Gas Line mm (inch) 3/4 (19.05) 3/4 (19.05) 3/4 (19.05) 7/8 (22.22) 1 (25.4)
आउटडोर पाइप का आकार
Liquid Line mm (inch) 3/8 (9.52)
स्वैग
3/8 (9.52)
स्वैग
3/8 (9.52)
स्वैग
3/8 (9.52)
swaged (3)
1/2 (12.7)
स्वैग
Gas Line mm (inch) 3/4 (19.05)
स्वैग
3/4 (19.05)
स्वैग
3/4 (19.05)
स्वैग
7/8 (22.22)
स्वैग
1-1/8 (28.6) ID to
fit field pipe
इनडोर पाइप का आकार
Liquid Line mm (inch) 3/8 (9.52)
स्वैग
3/8 (9.52)
स्वैग
3/8 (9.52)
स्वैग
3/8 (9.52)
swaged (3)
1/2 (12.7)
स्वैग
Gas Line mm (inch) 3/4 (19.05)
स्वैग
3/4 (19.05)
स्वैग
3/4 (19.05)
स्वैग
7/8 (22.22)
स्वैग
1 (25.4) swaged in
field to fit 1 (25.4)
नोट्स
(1) अधिकतम क्षेत्र पाइप लंबाई में शामिल.
(2) For pipe runs 0-20m 3/8” pipe must be used.
(3) Cut the swaged end of the unit to fit the field pipe.
Installation and Commissioning Guide Classic 2 Outdoor Units
Installation and Commissioning Guide – Classic 2 Split Ducted Outdoor Unit
डॉक्टर. क्रमांक 0525-073 वर्जन। 12 240708 23
सावधानी
Brazed joints should only be made while purging Nitrogen through the system.
Failure to do so will cause carbon deposit to be left on the internal pipe surface, that in turn can cause system failure and void
वारंटी.
विस्तार ए
खुला पाइप
रबर बंग
into pipe opening
सील बनाने के लिए
नाइट्रो
रेगुलेटर
Set to 2 L/s
N
I
T
R
O
G
E
N LIQUID
A PIPE
गैस पाईप
BRAZE JOINTS
इनडोर में इंटरकनेक्टिंग पाइप कार्य स्थापित करना, नाइट्रोजन ब्लीड प्रक्रिया (पहली फिट या रफ इनtagकेवल ई)
3. Run interconnecting pipe work from condenser location to evaporator.
4. Release pressure in evaporator and remove caps.
5. Fit copper tube into tail, set nitro bottle and regulator up at condenser end of pipe work.
6. Fit nitrogen line into liquid line with rubber bung to seal the connection. The seal will prevent air being sucked into pipe
काम।
7. Leave suction line open, set nitro regulator for nitrogen to flow through pipe work at 2 l/s flow rate @20kPa.
8. Braze required joints as quick as possible. See Diagram Above.
आउटडोर में इंटरकनेक्टिंग पाइप कार्य स्थापित करना, नाइट्रोजन ब्लीड प्रक्रिया (पहली फिट या रफ इनtagकेवल ई)
1. Starting with circuit 1 system, remove piping caps from the condenser and fit pipe work into tails.
2. Fit nitro hose onto suction ball valve and fit open hose onto liquid line post valve.
3. Set nitrogen regulator to 2 l/s flow rate through pipe work and evaporator.
4. Braze remaining joints as quick as possible.
5. ब्रेज़्ड जोड़ों को ठंडा होने दें और कनेक्शनों में रिसाव परीक्षण करें।
दस्तावेज़ / संसाधन
| एक्ट्रोनएयर CRA100S स्प्लिट डक्टेड यूनिट [पीडीएफ] स्थापना गाइड CRA100S, CRA130S, CRA130T, CRA150S, CRA150T, CRA170S, CRA170T, CRA200T, CRA230T, CCA130S, CCA150S, CCA170S, CCA170T, CCA200T, CCA230T, CRA100S स्प्लिट डक्टेड यूनिट, CRA100S, स्प्लिट डक्टेड यूनिट, डक्टेड यूनिट, यूनिट |
