ការណែនាំអំពីការដំឡើងបន្ទះ LED របស់ HANECO FXCRGB5M

HANECO FXCRGB5M LED Strip

ការណែនាំអំពីការប្រើប្រាស់ផលិតផល

• តែងតែផ្តាច់ការផ្គត់ផ្គង់ថាមពលមុនពេលដំឡើង។
• Clean the surface to ensure the self-adhesive backing will adhere properly.
• The mounting surface must be smooth, dry, and free from oils and waxes.
• Clean the installation surface
• Measure the length you need to install, cut at the nearest scissor mark line
• Connecting strip from the back release paper by one time. Do not press on the LEDs
• Components needed: SOB strip light, Cleaning cloth, Power supply, Scissor
• Always disconnect the power supply before shortening it. LED Strips can be cut along the mark of scissors.
• The maximum connect length of a single connection controller is 10m (32.8ft). If you choose a dual connection controller, you can connect 2 reels (with a maximum connection length of 7.5m on each side) to achieve an ultra-long 15m (49.2ft) LED light.

សំណួរគេសួរញឹកញាប់

• សំណួរ៖ តើខ្ញុំត្រូវកំណត់ការបញ្ជាពីចម្ងាយឡើងវិញដោយរបៀបណា?
  • A: Press ON/OFF for 5 seconds to reset the remote control and start connecting to the network.
• Q: What is the maximum connection length for a single connection controller?
  • A: The maximum connection length for a single connection controller is 10m (32.8ft).
• Q: Can I cut the LED strips to adjust the length?
  • A: LED strips can be cut along the marked scissor line to adjust the length as needed.

ការព្រមាន

1. The LED strip and accessories can’t be squeezed and folded.
2. គ្រឿងបន្លាស់ PCB មិនអាចត្រូវបានខូចខាតនៅពេលដំឡើង។
3. Pay attention to positive and negative polarities before installation, otherwise the LED strip may be damaged.
4. When connecting multiple LED strips, it is recommended to electrically connect in parallel. Please ensure the connected driver is rated higher than the combined total power of the LED strips.
5. Cut the LED strip along the logo mark.
6. When installed on an etal or conductive surface, the contact must adopt insulation protection.
7. Please prevent static electricity when installing. The product needs an anti-corrosion environment, such as avoiding dampness, water drop, or other adverse elements.
8. Do not lay the adapter and the control directly on the ground or where standing water may accumulate.

Always disconnect the power supply before installation. Clean the surface to ensure the self-adhesive backing will adhere properly. The mounting surface needs to be smooth, dry, and free from oils and waxes.

• Do not bend the LED strip sidewards.
• កុំបង្វិលបន្ទះ LED ។

ប្រតិបត្តិការត្រួតពិនិត្យពីចម្ងាយ

ប្រតិបតិ្តការ

Connecting & Installation Diagram

1. Clean the installation surface
2. Measure the length you need to install, and cut at the nearest scissor mark line.
3. Do not pull the whole LED strip from the back release paper at one time. No press on the leds.
4. ការភ្ជាប់

The maximum connect length of a single connection controller is 10m (32.8ft). if you choose a dual connection controller, you can connect 2 reels (with a maximum connection length of 7.5m on each side) to achieve an ultra-long 15m(49.2ft) LED light.

កាត់

• Always disconnect the power supply before shortening it. LED Strips can be cut along the mark of “scissor”.

វិមាត្រ

កូដផលិតផល៖ FXCRGB5M FXCRGBTW5M

សម្រាប់ព័ត៌មានបន្ថែម

• www.haneco.com.au 1300 001 LED

ឯកសារ/ធនធាន

HANECO FXCRGB5M LED Strip [pdf] ការណែនាំអំពីការដំឡើង FXCRGB5M, FXCRGB5M LED Strip, FXCRGB5M, LED Strip, Strip

ឯកសារយោង

• សៀវភៅណែនាំអ្នកប្រើប្រាស់