RAM 2024 20xx 1500 Vehicle Owner's Manual

Inhoud wegsteek

1 RAM 2024 20xx 1500 Vehicle

2 Produkgebruiksinstruksies

7 Gereelde Vrae (Gereelde Vrae)

8 Dokumente / Hulpbronne

8.1 Verwysings

9 Verwante plasings

RAM 2024 20xx 1500 Vehicle

Produkspesifikasies

Model: 20xx RAM 1500

Feature: Wireless Charging Pad
Wireless Charging Frequency: 128 kHz

Optional NFC Frequency: 13.56 MHz
Modulasie: VRA

Max. Target Power: 41.9 dBuV/m

Produkgebruiksinstruksies

Placing Your Phone on the Wireless Charging Pad:
Ensure the wireless charging pad is connected to power. Place your mobile phone within the prepared area on the anti-slip mat. The LED indicator light will confirm proper placement.

LED-aanwyserstatus:

Solid Light: Phone is detected and charging.

Blinking Light: Phone needs to be repositioned for proper charging.

Belangrike notas:

Keep the phone within the outlined area on the pad to maintain proper connection with the charging coils.
Avoid moving the phone during charging to prevent interruptions in charging speed.

If the phone overheats, charging may slow down or temporarily stop as a protective measure.

Waarskuwing:
Avoid placing the key fob on or near the charging pad to prevent heat damage. Keep at least 6 inches away from the pad to ensure proper vehicle operation.

Reguleringsvoldoening:
This device complies with FCC regulations regarding RF exposure. Maintain a safe distance of at least 8 cm from the device during operation.

DRAADLOSE LAAIPAD

Your vehicle may be equipped with a Qi ® wireless charging pad located below the center stack, within the storage compartment or ,if equipped ,inside of the center console. This charging pad is designed to wirelessly charge your Qi ® enabled mobile phone .Qi ® is a standard that allows wireless charging of your mobile phone.
Your mobile phone must be designed for Qi ® wireless charging .If the phone is not equipped with Qi ® wireless charging functionality, an aftermarket sleeve or a specialized back plate can be purchased from your mobile phone provider or a local electronics retailer. Please see your phone’s Owner’s Manual for further information.

The wireless charging pad is equipped with an anti-slip mat to hold your mobile phone in place, and an LED indicator light.
Place the device inside the prepared area delimited in the mat as shown in the image. Incorrect positioning will prevent the phone from charging.

LED-aanwyserstatus

Geen lig: Charging pad is idle or searching for a device. Device may not be compatible with the Qi® standard.
Blou Lig: Device is detected and is charging.

Red Light/Flashing: Internal error, or foreign object is detected.
Groen Lig: Device has completed battery charging (if device is equipped to transmit this information).

Instruksies

Important Notes Regarding This Vehicle’s Wireless Charging Pad:

The presence of the Near-Field Communication (NFC)function active on a smartphone could signal malfunction anomalies.

The ignition must be in the ON/RUN or START position in order for the phone to charge.
To avoid interference with the key fob search, the wireless charging pad will stop charging when any door or liftgate is opened, even if the engine is running.

Be sure to place the mobile device correctly(display facing upward and phone not covering LED)on wireless charging pad.
If the phone moves on the pad causing the red light to illuminate the phone will have to be picked up and placed back on the charging pad to resume charging.
Wireless charging is not as fast as when the phone is connected to a wired charger.
The phones protective case must be removed when placed on the wireless charging pad.
iPhone®12(including iPod®)is equipped with soft-ware to protect the device from overheating. When the software is active, the rate of charge is slowed down to protect the device.
Phones must always be placed on the wireless charging pad within the outline shown on the pad so that its charging parts connect with the charging coils of the system. Movement of the phone during charging may prevent or slow the rate of charge.
Having multiple applications open on the phone while charging will reduce the charging efficiency, and may even shut down an application that is actively running(i.e. Apple CarPlay®).This may also cause the phone to overheat.
Wireless chargers may implement certain methods to prevent the phone from overheating during charging such as slowing down the rate of charge. In certain instances ,the device may shut down for a brief period of time(when the device reaches a certain temperature).If this happens ,it does not mean there is a fault with the wireless charging pad. This may just be a protective measure to prevent damage to the phone.
The use of multiple wireless functions at the same time(wireless charging, Apple CarPlay® Android Auto™)could cause the device to overheat, resulting in limitation of the functions or it turning off. In this case ,it is recommended to connect the system using the USB port.
With a compatible device placed on the charging pad, and the ignition cycle to the OFF position, a reminder message may appear on the instrument cluster display to warn the driver.

VERSIGTIG!

The key fob should not be placed on the charging pad or within 6 inches (15 cm) of it. Doing so can cause excessive heat buildup and damage to the fob. Plac-ing the fob in close proximity of the charging pad blocks the fob from being detected by the vehicle and prevents the vehicle from starting.
Unless placing the phone to charge (transient intervals) the typical operating conditions of the
Wireless Charging Pad should be at least 3 inches (8 cm) away from the human body

FCC KENNISGEWING

Hierdie toestel voldoen aan deel 15 van die FCC-reëls. Werking is onderhewig aan die volgende twee voorwaardes:

Hierdie toestel mag nie skadelike steurings veroorsaak nie, en
Hierdie toestel moet enige steuring wat ontvang word aanvaar, insluitend steuring wat ongewenste werking kan veroorsaak.

Hierdie toerusting is getoets en gevind dat dit voldoen aan die limiete vir 'n Klas B digitale toestel, ooreenkomstig deel 15 van die FCC Reëls. Hierdie perke is ontwerp om redelike beskerming teen skadelike inmenging in 'n residensiële installasie te bied. Hierdie toerusting genereer, gebruik en kan radiofrekwensie-energie uitstraal en, indien dit nie geïnstalleer en gebruik word in ooreenstemming met die instruksies nie, kan dit skadelike steurings vir radiokommunikasie veroorsaak. Daar is egter geen waarborg dat inmenging nie in 'n spesifieke installasie sal voorkom nie. Indien hierdie toerusting wel skadelike steurings vir radio- of televisie-ontvangs veroorsaak, wat bepaal kan word deur die toerusting af en aan te skakel, word die gebruiker aangemoedig om die steuring deur een of meer van die volgende maatreëls te probeer regstel:

Heroriënteer of verskuif die ontvangsantenna. Verhoog die skeiding tussen die toerusting en ontvanger. Koppel die toerusting aan 'n uitlaat op 'n ander stroombaan as waaraan die ontvanger gekoppel is. Raadpleeg die handelaar of 'n ervare radio-/TV-tegnikus vir hulp.

Veranderinge of wysigings wat nie uitdruklik goedgekeur is deur die party wat verantwoordelik is vir voldoening nie, kan die gebruiker se magtiging om die toerusting te gebruik, vernietig.

Hierdie toerusting voldoen aan FCC-bestralingsblootstellinglimiete wat vir 'n onbeheerde omgewing uiteengesit is. Hierdie toerusting moet geïnstalleer en bedryf word met 'n minimum afstand van 8 cm tussen die verkoeler en jou liggaam. Hierdie sender moet nie saam met enige ander antenna of sender werksaam wees nie.

Die FCC-sertifisering van hierdie toestel verwys na RF-blootstellingstoetsing wat uitgevoer word in tipiese bedryfstoestande, waar 'n persoon te alle tye nie nader as 8 sentimeter van die toesteloppervlak is nie, behalwe vir nie-herhalende patrone met verbygaande tydintervalle in die orde van 'n sekonde . Slegs in die genoemde toestande word getoon dat die toestel ten volle aan die FCC RF-blootstellingsvereistes van KDB 447498 voldoen.

INDUSTRY CANADA KENNISGEWING
This radio transmitter has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser ) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p) is not more than that necessary for successful communication. This device complies with Industry Canada license- exempt RSS standard(s). Operation is subject to the following two conditions:

Hierdie toestel mag nie inmenging veroorsaak nie, en
Hierdie toestel moet enige steuring aanvaar, insluitend steuring wat ongewenste werking van die toestel kan veroorsaak.

FCC ID : 2A6WXWCSTE40A, 2A6WXWCSTE40AA

ISED : 28559-WCSTE40A, 28559-WCSTE40AA
Frekwensie : Wireless Charging 128 kHz (Optional NFC 13.56 MHz)
Modulasie: VRA

Maks. Target Power : 41.9 dBuV/m

Gereelde Vrae (Gereelde Vrae)

Q: What should I do if my phone is not charging on the pad?
- A: Make sure your phone is properly placed within the outlined area on the mat. Reposition if needed until the LED indicator confirms charging.

Q: Can I leave my phone on the charging pad overnight?
- A: It is recommended not to leave your phone on the charging pad overnight to prevent overheating and prolong battery life.
Q: Why does my phone’s charging speed vary?
- A: Movement of the phone during charging or overheating can affect the speed of charging. Ensure proper placement and avoid overheating to maintain optimal charging speed.