This repo contains Tom Lutz's personal notes and scripts for configuring a new Raspberry Pi 3 Model B with some applications, based on the default raspbian installation.
This is not all original material. I leveraged tutorials from the following sites:
- ioquake3 via github.com/tommylutz/quake3 (has minor fixes to link line and build script)
sudo apt-get install libsdl1.2-dev
git clone https://github.com/tommylutz/quake3.git
cd quake3
./build_rpi_raspbian.sh
Find pak0.pk3, pak1.pk3, ... pak8.pk3 files from a legit copy of Quake 3 Arena, and copy to build/release-linux-arm/baseq3/
./start_server.sh
The start_server.sh script will emit instructions on what to add to /etc/rc.local to start up quake 3 dedicated server on boot, if you'd like.
The hostapd package is required to turn RPi3 into a wifi hotspot.
After completing these steps, you
should be able to see the SSID of your Raspberry Pi broadcasting (Pi3-AP
unless you changed it). You will not get an IP address until you
configure dnsmasq (later).
First, install hostapd using aptget.
sudo apt-get install dnsmasq hostapd
Next, create the hostapd config file, /etc/hostapd/hostapd.conf
# This is the name of the WiFi interface we configured above
interface=wlan0
# This is the name of the network
ssid=Pi3-AP
# Use the 2.4GHz band
hw_mode=g
# Use channel 6
channel=6
# Enable 802.11n
ieee80211n=1
# Enable WMM
wmm_enabled=1
# Enable 40MHz channels with 20ns guard interval
ht_capab=[HT40][SHORT-GI-20][DSSS_CCK-40]
# Accept all MAC addresses
macaddr_acl=0
# Use WPA authentication
auth_algs=1
# Require clients to know the network name
ignore_broadcast_ssid=0
# Use WPA2
wpa=2
# Use a pre-shared key
wpa_key_mgmt=WPA-PSK
# The network passphrase
wpa_passphrase=raspberry
# Use AES, instead of TKIP
rsn_pairwise=CCMP
Tell hostapd where the config file is by editing /etc/default/hostapd
DAEMON_CONF="/etc/hostapd/hostapd.conf"
Edit /etc/network/interfaces to set wlan0 to static ip address:
allow-hotplug wlan0
iface wlan0 inet static
address 192.168.2.1
netmask 255.255.255.0
network 192.168.2.0
broadcast 192.168.2.255
Restart your wlan0 interface and check that it has the correct IP address assigned.
sudo ifdown wlan0
sudo ifup wlan0
ifconfig wlan0
Start hostapd
sudo service hostapd start
Check that the access point is visible from a wifi client, such as your phone.
First, install the package
sudo apt-get install dnsmasq
Next, configure your DNS service in /etc/dnsmasq.conf
This is the entire contents of the file. You may wish to save the original one to .sav or something.
interface=wlan0
listen-address=192.168.2.1
bind-interfaces
server=8.8.8.8
domain-needed
bogus-priv
dhcp-range=192.168.2.100,192.168.2.200,12h
dhcp-option=option:router,192.168.2.1
Fire up the service (yes, it will auto start on next boot)
sudo service dnsmasq start
Set up IP routing rules
sudo iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE
sudo iptables -A FORWARD -i eth0 -o wlan0 -m state --state RELATED,ESTABLISHED -j ACCEPT
sudo iptables -A FORWARD -i wlan0 -o eth0 -j ACCEPT
Add this line to /etc/rc.local
echo 1 > /proc/sys/net/ipv4/ip_forward
Also run this so it takes effect immediately
sudo sh -c "echo 1 > /proc/sys/net/ipv4/ip_forward"
Configure iptables persistently. First, export iptables config to a file:
sudo sh -c "iptables-save > /etc/iptables.ipv4.nat"
Now add this to /etc/rc.local to load the config on boot:
iptables-restore < /etc/iptables.ipv4.nat
- Include certificate installation
- Download the "Receiver for Linux (ARM HF)" debian package from https://www.citrix.com/downloads/citrix-receiver/linux/receiver-for-linux-latest.html (wget may not work, as you have to accept the license)
wget https://downloads.citrix.com/12939/icaclient_13.5.0.10185126_armhf.deb?__gda__=1489922811_35d02cb8c45ec8bf003218ef82d5d6dc
- Try to install the package, but fail miserably due to missing dependencies.
sudo apt-cache search <SEARCH TERM>to search for the appropriate packages andsudo apt-get install <PACKAGES>to install them - Symlink root certs from mozilla into the Citrix folder.
sudo ln /usr/share/ca-certificates/mozilla/* /opt/Citrix/ICAClient/keystore/cacerts/
sudo apt-get update
sudo apt-get upgrade
- Wiimotes: http://www.instructables.com/id/Wiimote-Controller-Configuration-for-Raspberry-Pi-/?ALLSTEPS
sudo apt-get install python-cwiid
sudo apt-get install wminput
File /etc/udev/rules.d/wiimote.rules
KERNEL=="uinput", MODE="0666"
Check bluetooth
/etc/init.d/bluetooth status
File /home/pi/mywinput
#WiiMote
Wiimote.A = BTN_A
Wiimote.B = BTN_B
Wiimote.Dpad.X = ABS_Y
Wiimote.Dpad.Y = -ABS_X
Wiimote.Minus = BTN_SELECT
Wiimote.Plus = BTN_START
Wiimote.Home = BTN_MODE
Wiimote.1 = BTN_X
Wiimote.2 = BTN_Y
# Nunchuk
Nunchuk.C = BTN_C
Nunchuk.Z = BTN_Z
Plugin.led.Led1 = 1
#Plugin.led.Led2 = 1
Plugin.led.Led3 = 1
#Plugin.led.Led4 = 1