Measurement and Calibration tool VISU tool is the Phinia product for calibration of ECU function parameters. VISU supports online and offline adjustments of characterictic values, curves and tables. Simultaneously to the parameter optimization, VISU allows to acquire measurement signals from ECUs as well as from their vehicle environment.
In addition to the measurement and calibration core system, VISU includes tools for reading faults, writing Injector parameters and for reprogramming ECU software into flash memory. VISU uses Flasher tool for running diagnostic commands (e.g. flashing HEX file to ECU). If Flasher is installed, VISU will find it automatically. VISU runs "plugin" function on the Flasher. "Plugin" is the DLL file which describes the diagnostic routines for Flasher tool.
Calibration: Online/offline calibration, 2 page (work / reference page) / 1 page concept, support of dependent and adaptive parameters, editors for scalars and multidimensional parameters (1D to 3D)
Calibration data management: Listing, comparing and copying calibration data, functional view, support of maturity levels, version management of calibration data sets
Measurement data acquisition: Acquisition and online display of measurement values, calibration parameters (scalars, characteristic curves/diagrams), numerous trigger options, online signal calculation, XT/XY-oscilloscope and table display, simultaneous acquisition of parallel measurements, cold start acquisition, multi-ECU measurement, stimulation, polling-DAQ
Measurement data analysis: XT/XY-oscilloscope, table display, cursor, offline trigger, signal calculation, statistical analysis, calculated signals (equation) on the fly, various export features
Flash programming: ECU-specific flash programming via Flasher tool
Experiment environment: Numerous user-friendly display and control elements, interface for integrating customer-specific elements
Hardware configuration: Configuration of ECU and bus interfaces, and measurement modules, hardware auto-scan
Bus monitoring: Advanced bus monitoring features for CAN/FlexRay/LIN buses, grouped or chronological view of traces, J1939 (/21 and /22) transmission and monitoring
ECU diagnostics: via Flasher tool, Error memory reading and clearing, validation of services of diagnostic services, Automation of service sequences, support of ODX into diagnostic script
Test automation: Remote control via ASAP3 and iLinkRT
ECU calibration: CAN (CCP, XCP, UDS), CAN FD (XCP, UDS), Ethernet (XCP, UDS), FlexRay (XCP), Serial port (XCP), X-ETK Interface (board) ETK and F-ETK interfaces are not supported.
Bus monitoring: CAN, CAN FD, FlexRay, LIN
Measurement devices: CAN (Vector, Peak, Softing, Kvazer, any SAE J2534 compliant device), CAN-FD (Vector, Peak), Flexray (Vector), LIN (Vector, Intrepid, Peak)
Test bench / automation: ASAM ASAP3 (v2.0, v2.1.1, v3.0), iLinkRT v2.0
| Bus/Protocol | CCP | XCP | UDS | Monitoring |
|---|---|---|---|---|
| CAN | y | y | y | y |
| FlexRay | y | y | ||
| LIN | y | |||
| Ethernet | y | y | ||
| Serial | y |
ECU description: ASAM MCD-2 MC (A2L) up to 1.7.1
CAN Bus description: DBC, FIBEX (From v3.0.0 to v4.1.2), ARXML (AUTOSAR 4.2.2 schema)
FlexRay Bus description: FIBEX (From v3.0.0 to v4.1.2), ARXML (AUTOSAR 4.2.2 schema)
LIN Bus description: LDF (in conformity with LIN 2.2 Rev A)
Calibration data: Intel HEX, Motorola S19, S28, S37
Calibration data(physical representation): DCM, CVX, PaCo, ASAM CDF (v2.0, v2.1)
Measurement file data: ASAM MDF (v3, v3.3, v4.0, v4.1), ASCII
Bus trace file: BLF, ASC