Network+ Guide to

Networks
6th Edition
Chapter 3
Transmission Basics and
Networking Media
 Objectives
• Explain basic data transmission concepts, including full
duplexing, attenuation, latency, and noise
• Describe the physical characteristics of coaxial cable,
STP, UTP, and fiber-optic media
• Compare the benefits and limitations of different
networking media
• Explain the principles behind and uses for serial cables
• Identify wiring standards and the best practices for
cabling buildings and work areas

2
 Transmission Basics
• Transmit
– Issue signals along network medium
• Transmission
– Process of transmitting
– Signal progress after transmitting
• Transceiver
– Transmits and receives signals

3
 Analog and Digital Signaling
• Important data transmission characteristic
– Signaling type: analog or digital
• Volt
– Electrical current pressure
• Electrical signal strength
– Directly proportional to voltage
– Signal voltage
• Signals
– Current, light pulses, electromagnetic waves
4
 Analog and Digital Signaling
• Analog data signals(cont’d.)
– Voltage varies continuously
• Fundamental properties of analog signals
– Amplitude
• Measure of strength at given point in time
– Frequency
• Number of times amplitude cycles over fixed time
– Wavelength
• Distance between one peak and the next
– Phase
• Progress of wave over time compared to a fixed point

5
Figure 3-1 An example of an analog signal
Courtesy Course Technology/Cengage Learning

6
Figure 3-2 Waves with a 90 degree phase difference

7
 Analog and Digital Signaling
(cont’d.)
• Analog signal benefit over digital
– More variable
• Convey greater subtleties with less energy
• Drawback of analog signals
– Varied and imprecise voltage
• Susceptible to transmission flaws
• Digital signals
– Pulses of voltages
• Positive voltage represents a 1
• Zero voltage represents a 0
8
Figure 3-3 An example of a digital signal

Figure 3-4 Components of a byte

9
 Analog and Digital Signaling
(cont’d.)
• Convert byte to decimal number
– Determine value represented by each bit
– Add values
• Convert decimal number to a byte
– Reverse the process
• Convert between binary and decimal
– By hand or calculator

10
 Analog and Digital Signaling
(cont’d.)
• Digital signal benefit over analog signal
– More reliable
– Less severe noise interference
• Digital signal drawback
– Many pulses required to transmit same information
• Overhead
– Nondata information
– Required for proper signal routing and interpretation
– Example: network layer addressing information

11
 Data Modulation
• Data relies on digital transmission
• Network connection may handle only
analog signals
• Modem
– Accomplishes translation
– Modulator/demodulator
• Data modulation
– Technology modifying analog signals
– Make data suitable for carrying over communication
path 12
 Data Modulation (cont’d.)
• Carrier wave
– Combined with another analog signal
– Produces unique signal
• Transmitted from one node to another
– Preset properties
– Purpose: convey information
• Information wave (data wave)
– Added to carrier wave
– Modifies one carrier wave property

13
 Data Modulation (cont’d.)
• Frequency modulation
– Carrier frequency modified by application of data
signal
• Amplitude modulation
– Carrier signal amplitude modified by application of
data signal
• Digital subscriber line (DSL)
– Also makes use of modulation

14
Figure 3-5 A carrier wave modified through frequency modulation
15
 Simplex, Half-Duplex, and
• Simplex
Duplex
– Signals travel in one direction
• Half-duplex transmission
– Signals travel in both directions
• One at a time
– Shared communication channel
• Full-duplex
– Signals travel in both directions simultaneously
– Used on data networks

16
Figure 3-6 Simplex, half-duplex, and full-duplex transmission

17
 Simplex, Half-Duplex, and
Duplex (cont’d.)
• Channel
– Distinct communication path between nodes
– Separated physically or logically
• Full duplex advantage
– Increases speed of data travel
• Some modems and NICs allow specifying
half- or full-duplex communication
– Modern NICs use full duplex by default
18
 Multiplexing
• Multiplexing
– Multiple signals
– Travel simultaneously over one medium
• Subchannels
– Logical multiple smaller channels
• Multiplexer (mux)
– Combines many channel signals
• Demultiplexer (demux)
– Separates combined signals
– Regenerates them
19
 Multiplexing (cont’d.)
• Time division multiplexing (TDM)
– Divides channel into multiple time intervals

Figure 3-7 Time division multiplexing

20
 Multiplexing (cont’d.)
• Statistical multiplexing
– Transmitter assigns slots to nodes
• According to priority, need
– More efficient than TDM

Figure 3-8 Statistical multiplexing

21
 Multiplexing (cont’d.)
• Frequency division multiplexing (FDM)
– Unique frequency band for each communications
subchannel
– Cellular telephone transmission
– DSL Internet access

Figure 3-9 Frequency division multiplexing

22
 Multiplexing (cont’d.)
• Wavelength division multiplexing (WDM)
– One fiber-optic connection
– Carries multiple light signals simultaneously

Figure 3-10 Wavelength division multiplexing

23
 Multiplexing (cont’d.)
• Dense wavelength division multiplexing
(DWDM)
– Used on most modern fiber-optic networks
– Extraordinary capacity

24
 Relationships Between Nodes
• Point-to-point transmission
– One transmitter and one receiver
• Point-to-multipoint transmission
– One transmitter and multiple receivers
• Broadcast transmission
– One transmitter and multiple, undefined receivers
– Used on wired and wireless networks
– Simple and quick
• Nonbroadcast
– One transmitter and multiple, defined recipients 25
Figure 3-11 Point-to-point versus broadcast transmission
26
 Throughput and Bandwidth
• Throughput
– Amount of data transmitted during given time period
– Also called capacity or bandwidth
– Expressed as bits transmitted per second
• Bandwidth (strict definition)
– Difference between highest and lowest frequencies
medium can transmit
– Range of frequencies
– Measured in hertz (Hz)

27
Table 3-1 Throughput measures

28
 Baseband and Broadband
• Baseband transmission
– Digital signals sent through direct current (DC) pulses
applied to wire
– Requires exclusive use of wire’s capacity
– Transmit one signal (channel) at a time
– Example: Ethernet
• Broadband transmission
– Signals modulated as radio frequency (RF) analog
waves
– Uses different frequency ranges
– Does not encode information as digital pulses
29
 Transmission Flaws
• Noise
– Any undesirable influence degrading or distorting
signal
• Types of noise
– EMI (electromagnetic interference)
• Example: radio frequency interference
– Cross talk
• Signal on one wire infringes on adjacent wire signal
• Near end cross talk (NEXT) occurs near source

30
Figure 3-12 Cross talk between wires in a cable

31
 Transmission Flaws (cont’d.)
• Attenuation
– Loss of signal’s strength as it travels away from
source
• Signal boosting technology
– Analog signals pass through amplifier
• Noise also amplified
– Regeneration
• Digital signals retransmitted in original form
• Repeater: device regenerating digital signals
– Amplifiers and repeaters
• OSI model Physical layer

32
Figure 3-13 An analog signal distorted by noise and then amplified

Figure 3-14 A digital signal distorted by noise and then repeated 33

 Transmission Flaws (cont’d.)
• Latency
– Delay between signal transmission and receipt
– May cause network transmission errors
• Latency causes
– Cable length
– Intervening connectivity device
• Round trip time (RTT)
– Time for packet to go from sender to receiver, then
back from receiver to sender

34
Common Media Characteristics
• Selecting transmission media
– Match networking needs with media characteristics
• Physical media characteristics
– Throughput
– Cost
– Noise immunity
– Size and scalability
– Connectors and media converters

35
 Throughput
• Most significant factor in choosing
transmission method
• Causes of throughput limitations
– Laws of physics
– Signaling and multiplexing techniques
– Noise
– Devices connected to transmission medium
• Fiber-optic cables allow faster throughput
– Compared to copper or wireless connections

36
 Cost
• Precise costs difficult to pinpoint
• Media cost dependencies
– Existing hardware, network size, labor costs
• Variables influencing final cost
– Installation cost
– New infrastructure cost versus reuse
– Maintenance and support costs
– Cost of lower transmission rate affecting productivity
– Cost of downtime
– Cost of obsolescence
37
 Noise Immunity
• Noise distorts data signals
– Distortion rate dependent upon transmission media
• Fiber-optic: least susceptible to noise
• Limit noise impact on network
– Cable installation
• Far away from powerful electromagnetic forces
– Select media protecting signal from noise
– Antinoise algorithms

38
 Size and Scalability
• Three specifications
– Maximum nodes per segment
– Maximum segment length
– Maximum network length
• Maximum nodes per segment dependency
– Attenuation and latency
• Maximum segment length dependency
– Attenuation and latency plus segment type

39
 Size and Scalability (cont’d.)
• Segment types
– Populated: contains end nodes
– Unpopulated: no end nodes
• Also called link segment
• Segment length limitation
– After certain distance, signal loses strength
• Cannot be accurately interpreted

40
 Connectors and Media
Converters
• Connectors
– Hardware connecting wire to network device
– Specific to particular media type
– Affect costs
• Installing and maintaining network
• Ease of adding new segments or nodes
• Technical expertise required to maintain network
• Media converter
– Hardware enabling networks or segments running on
different media to interconnect and exchange signals
41
Figure 3-15 Copper wire-to-fiber media converter

42
 Coaxial Cable
• Central metal core (often copper)
surrounded by:
– Insulator
– Braided metal shielding (braiding or shield)
– Outer cover (sheath or jacket)

Figure 3-16 Coaxial cable

43
 Coaxial Cable (cont’d.)
• High noise resistance
• Advantage over twisted pair cabling
– Carry signals farther before amplifier required
• Disadvantage over twisted pair cabling
– More expensive
• Hundreds of specifications
– RG specification number
– Differences: shielding and conducting cores
• Transmission characteristics

44
 Coaxial Cable (cont’d.)
• Conducting core
– American Wire Gauge (AWG) size
– Larger AWG size, smaller wire diameter
• Data networks usage
– RG-6
– RG-8
– RG-58
– RG-59

45
Figure 3-17 F-Type connector Figure 3-18 BNC connector
Courtesy of MCM Electronics, Inc. © Igor Smichkov/Shutterstock.com

46
 Twisted Pair Cable
• Color-coded insulated copper wire pairs
– 0.4 to 0.8 mm diameter
– Encased in a plastic sheath

Figure 3-19 Twisted pair cable

47
 Twisted Pair Cable (cont’d.)
• More wire pair twists per foot
– More resistance to cross talk
– Higher-quality
– More expensive
• Twist ratio
– Twists per meter or foot
• High twist ratio
– Greater attenuation

48
 Twisted Pair Cable (cont’d.)
• Hundreds of different designs
– Twist ratio, number of wire pairs, copper grade,
shielding type, shielding materials
– 1 to 4200 wire pairs possible
• Wiring standard specification
– TIA/EIA 568
• Most common twisted pair types
– Category (cat) 3, 5, 5e, 6, 6a, 7
– CAT 5 or higher used in modern LANs

49
 Twisted Pair Cable (cont’d.)
• Advantages
– Relatively inexpensive
– Flexible
– Easy installation
– Spans significant distance before requiring repeater
– Accommodates several different topologies
• Two categories
– Shielded twisted pair (STP)
– Unshielded twisted pair (UTP)

50
 STP (Shielded Twisted Pair)
• Individually insulated
• Surrounded by metallic substance
shielding (foil)
– Barrier to external electromagnetic forces
– Contains electrical energy of signals inside
– May be grounded
Figure 3-20 STP cable

51
 UTP (Unshielded Twisted Pair)
• One or more insulated wire pairs
– Encased in plastic sheath
– No additional shielding
• Less expensive, less noise resistance

Figure 3-21 UTP cable

52
 Comparing STP and UTP
• Throughput
– STP and UTP can transmit the same rates
• Cost
– STP and UTP vary
• Connector
– STP and UTP use Registered Jack 45
– Telephone connections use Registered Jack 11

53
 Comparing STP and UTP
(cont’d.)
• Noise immunity
– STP more noise resistant
• Size and scalability
– Maximum segment length for both: 100 meters

54
Terminating Twisted Pair Cable
• Patch cable
– Relatively short cable
– Connectors at both ends
• Proper cable termination techniques
– Basic requirement for two nodes to communicate
• Poor terminations:
– Lead to loss or noise
• TIA/EIA standards
– TIA/EIA 568A
– TIA/EIA 568B
55
Figure 3-24 TIA/EIA 568A standard Figure 3-25 TIA/EIA 568B standard
terminations terminations
56
 Terminating Twisted Pair Cable
(cont’d.)
• Straight-through cable
– Terminate RJ-45 plugs at both ends identically
• Crossover cable
– Transmit and receive wires on one end reversed

Figure 3-26 RJ-45 terminations

on a crossover cable
Courtesy Course
Technology/Cengage Learning

57
Terminating Twisted Pair Cable
(cont’d.)
• Termination tools
– Wire cutter
– Wire stripper
– Crimping tool
• After making cables:
– Verify data transmit and receive

58
 Fiber-Optic Cable
• Fiber-optic cable (fiber)
– One or more glass or plastic fibers at its center (core)
• Data transmission
– Pulsing light sent from laser or light-emitting diode (LED) through
central fibers
• Cladding
– Layer of glass or plastic surrounding fibers
– Different density from glass or plastic in strands
– Reflects light back to core
– Allows fiber to bend

59
 Fiber-Optic Cable (cont’d.)
• Plastic buffer outside cladding
– Protects cladding and core
– Opaque to absorb escaping light
– Surrounded by Kevlar (polymeric fiber) strands
• Plastic sheath covers Kevlar strands

Figure 3-30 A fiber-optic cable

60
 Fiber-Optic Cable (cont’d.)
• Different varieties
– Based on intended use and manufacturer

Figure 3-31 Zipcord fiber-optic patch cable

61
 Fiber-Optic Cable (cont’d.)
• Benefits over copper cabling
– Extremely high throughput
– Very high noise resistance
– Excellent security
– Able to carry signals for longer distances
– Industry standard for high-speed networking
• Drawbacks
– More expensive than twisted pair cable
– Requires special equipment to splice

62
 SMF (Single-Mode Fiber)
• Consists of narrow core (8-10 microns in
diameter)
– Laser-generated light travels over one path
• Little reflection
– Light does not disperse as signal travels
• Can carry signals many miles:
– Before repeating required
• Rarely used for shorter connections
– Due to cost

63
 MMF (Multimode Fiber)
• Contains core with larger diameter than
single-mode fiber
– Common sizes: 50 or 62.5 microns
• Laser or LED generated light pulses travel
at different angles
• Greater attenuation than single-mode fiber
• Common uses
– Cables connecting router to a switch
– Cables connecting server on network backbone
64
 Fiber-Optic Converters
• Required to connect multimode fiber
networks to single-mode fiber networks
– Also fiber- and copper-based parts of a network

Figure 3-38 Single-mode to multimode

converter

65
 Serial Cables
• Data transmission style
– Pulses issued sequentially, not simultaneously
• Serial transmission method
– RS-232
• Uses DB-9, DB-25, and RJ-45 connectors

66
 Structured Cabling
• Cable plant
– Hardware that makes up the enterprise cabling
system
• Cabling standard
– TIA/EIA’s joint 568 Commercial Building Wiring
Standard
• Also known as structured cabling
• Based on hierarchical design

67
Figure 3-42 TIA/EIA structured cabling in an enterprise

68
 Structured Cabling (cont’d.)
• Components
– Entrance facilities
– MDF (main distribution frame)
– Cross-connect facilities
– IDF (intermediate distribution frame)
– Backbone wiring
– Telecommunications closet
– Horizontal wiring
– Work area

69
Structured Cabling (cont’d.)

Table 3-2 TIA/EIA specifications for backbone cabling

Courtesy Course Technology/Cengage Learning

70
 Best Practices for Cable
Installation and Management
• Choosing correct cabling
– Follow manufacturers’ installation guidelines
– Follow TIA/EIA standards
• Network problems
– Often traced to poor cable installation techniques
• Installation tips to prevent Physical layer failures
– See Pages 121-122 in the text

71
 Summary
• Information transmission methods
– Analog
– Digital
• Multiplexing allows multiple signals to travel
simultaneously over one medium
• Full and half-duplex specifies whether signals can travel
in both directions or one direction at a time
• Noise distorts both analog and digital signals
• Attenuation
– Loss of signal as it travels

72
 Summary (cont’d.)
• Coaxial cable composed of core, insulator,
shielding, sheath
• Types of twisted pair cable
– Shielded and unshielded
• Fiber-optic cable transmits data through
light passing through the central fibers

73
 Summary (cont’d.)
• Fiber-optic cable categories
– Single and multimode fiber
• Serial communication often used for short
connections between devices
• Structured cabling standard provides
wiring guidelines

74