d301672x012 Modulo de Entradas - Salidas Analogicas Controlwave
d301672x012 Modulo de Entradas - Salidas Analogicas Controlwave
d301672x012 Modulo de Entradas - Salidas Analogicas Controlwave
ControlWave® Micro
Analog Input / Output Modules
The Analog Input (AI), Analog Output (AO), and Analog
Input/Output (AI/O) modules provide the ControlWave®
4 Isolated Analog Outputs Module
Micro with the ability to monitor and control various analog The 4 Isolated Analog Outputs module provides four analog
field signals. The following AI, AO, and AI/O modules are outputs that can be individually jumper configured for 4 to
available. 20 mA or 1 to 5 Vdc isolated operation. Analog outputs are
electrically isolated from the CPU power system. Calibration
6 Analog Inputs and 2 Analog Outputs module
data for each channel is stored in an onboard EEPROM for
6 Analog Inputs module both current and voltage mode configurations. The 4
8 Isolated Analog Inputs module Isolated Analog Outputs module is available with local or
4 Isolated Analog Outputs module remote terminations.
All I/O modules have surge protection that meets C37.90- Local or Remote Terminations
1978 and IEC 801-5 specifications.
All analog I/O modules are available factory configured for
6 Analog Inputs and 2 Analog either local terminations that consist of two 10-point
terminal block assemblies or remote terminations that
Outputs Module consist of two 14-pin mass termination headers.
The 6 Analog Inputs and 2 Analog Outputs module provides Terminations are pluggable and accept a maximum wire
six analog inputs and two analog outputs. Analog inputs are size of 14 AWG (American Wire Gauge).
externally sourced, single-ended, and individually jumper Remote terminations provide a convenient alternative to
configurable for either 4 to 20 mA or 1 to 5 Vdc operation. the standard direct connect termination. Remote
Analog outputs are externally sourced (11 to 30 Vdc) and terminations allow a concentration of electrical connections
individually jumper configurable for 4 to 20 mA or 1 to 5 from one or more controllers to be located in a single area,
Vdc. Surge suppression between each signal and ground is such as the rear of a 19-inch cabinet. For more information
achieved with 30 Vdc transorbs. The 6 Analog Inputs and 2 on remote terminations, refer to Product Date Sheet
Analog Outputs module is available with local or remote CWMICRO.
terminations.
Terminal Terminal
Definition Definition
Block 1 Block 2
1 Positive Analog Input 1 1 Positive Analog Input 5
2 Gr ound 2 Gr ound
3 Positive Analog Input 2 3 Positive Analog Input 6
4 Gr ound 4 Gr ound
5 Positive Analog Input 3 5 No t Used
6 Gr ound 6 No t Used
7 Positive Analog Input 4 7 No t Used
8 Gr ound 8 No t Used
9 Gr ound 9 No t Used
10 Gr ound 10 No t Used
Inputs
Quantity Six channels
Type Single-ended, externally sourced, jumper configurable as 1 to 5 Vdc or 4 to 20 mA.
Resolution 14-bit SAR ADC
Impedance 1 to 5 Vdc Inputs 1 MΩ
4 to 20 mA Inputs 250 Ω
Reference Accuracy (after ±0.1% of span.
calibration) at 25°C (77°F)
Accuracy Over Operating ±0.2% of span.
Temperature Range
[—40 to 70°C (—40 to 158°F)]
Input Filter 500 ms to 99.9% of input signal.
Conversion Time 10 ms per channel
Surge Suppression 30 Vdc transorb between signal and ground
Meets ANSI/IEEE C37.90-1978 specifications
Power
Consumption Analog Input 0.011 W
Analog Output 0.014 W
Analog Output 1.13 W
External Loop
Power at 24 Vdc
Physical
Dimensions 152.4 mm H by 25.4 mm W by 88.9 mm L (6 in. H by 1 in. W by 3.5 in. L)
Weight 128 g (4.5 oz)
2 www.EmersonProcess.com/Remote
CWMICRO:AIO February 2012
ControlWave Micro Non Isolated 6 Analog Inputs and 2 Analog Outputs Module
Terminal Terminal
Definition Definition
Block 1 Block 2
1 Positive Analog Input 1 1 Positive Analog Input 5
2 Ground 2 Ground
3 Positive Analog Input 2 3 Positive Analog Input 6
4 Ground 4 Ground
5 Positive Analog Input 3 5 Positive Analog Output 1
6 Ground 6 Ground
7 Positive Analog Input 4 7 Positive Analog Output 2
8 Ground 8 Ground
9 Ground 9 External Voltage
10 Ground 10 Ground
Inputs
Quantity Six channels
Type Single-ended, externally sourced, jumper configurable as 1 to 5 Vdc or 4 to 20 mA
Resolution 14-bit SAR ADC
Impedance 1 to 5 Vdc Inputs 1 MΩ
4 to 20 mA Inputs 250 Ω
Reference Accuracy (after ±0.1% of span
calibration) at 25°C (77°F)
Accuracy Over Operating ±0.2% of span
Temperature Range
[—40 to 70°C (—40 to 158°F)]
Input Filter 500 ms to 99.9% of input signal
Conversion Time 10 ms per channel
Surge Suppression 30 Vdc transorb between signal and ground
Meets ANSI/IEEE C37.90-1978 specifications
www.EmersonProcess.com/Remote 3
February 2012 CWMICRO:AIO
Outputs
Quantity Two channels
Type Single-ended, externally sourced, jumper configurable as 1 to 5 Vdc or 4 to 20 mA
1 to 5 Vdc 5 mA maximum output current into external load with external
voltage range of 11 to 30 Vdc
4 to 20 mA 250 Ω load with 11 Vdc external power source
650 Ω load with 24 Vdc external power source
Resolution 12 bits
Reference Accuracy (after Current Output ±0.1% of span
calibration) at 25°C (77°F)
Voltage Output ±0.1% + [0.057*Iload in mA]% of span
Accuracy Over Operating Current Output ±0.2% of span
Temperature Range
[—20 to 70°C (—4 to 158°F)] Voltage Output ±0.2% + [0.057*Iload in mA]% of span
4 www.EmersonProcess.com/Remote
CWMICRO:AIO February 2012
ControlWave Micro Isolated 8 High Common Mode (HCM) Analog Inputs Module
Terminal Terminal
Definition Definition
Block 1 Block 2
1 Positive Analog Input 1 1 Positive Analog Input 5
2 Negative Analog Input 1 2 Negative Analog Input 5
3 Positive Analog Input 2 3 Positive Analog Input 6
4 Negative Analog Input 2 4 Negative Analog Input 6
5 Positive Analog Input 3 5 Positive Analog Input 7
6 Negative Analog Input 3 6 Negative Analog Input 7
7 Positive Analog Input 4 7 Positive Analog Input 8
8 Negative Analog Input 4 8 Negative Analog Input 8
9 Isolated Ground 9 Isolated Ground
10 Isolated Ground 10 Isolated Ground
Inputs
Quantity Eight channels
Type Isolated, jumper configurable as externally sourced 1 to 5 Vdc, 0 to 10 Vdc,
4 to 20 mA, or internally sourced 4 to 20 mA.
Resolution 21-bit Delta Sigma ADC
Impedance 1 to 5 Vdc Inputs
4 to 20 mA Inputs
Field Device Supply 24 Vdc at 200 mA
Reference Accuracy (after ±0.1% of span
calibration) at 25°C (77°F)
Accuracy Over Operating ±0.2% of span
Temperature Range
[—20 to 70°C (—4 to 158°F)]
Accuracy Over Operating ±0.3% of span
Temperature Range
[—40 to 70°C (—40 to 158°F)]
Over Range 0.8 to 5.2 Vdc (for 1 to 5 Vdc Input)
3.2 to 20.8 mA (for 4 to 20 mA Input)
Common Mode Rejection 75 dB
Normal Mode Rejection 40 dB
Voltage Input Impedance 1 MΩ
Current Input Impedance 250 Ω
Bus Access 8 bits wide
Channel to System Bus Isolation 500 Vdc
www.EmersonProcess.com/Remote 5
February 2012 CWMICRO:AIO
Terminal Terminal
Definition Definition
Block 1 Block 2
1 Analog Output 1 Current 1 Analog Output 3 Current
2 Analog Output 1 Return 2 Analog Output 3 Return
3 Analog Output 1 Voltage 3 Analog Output 3 Voltage
4 Analog Output 1 Return 4 Analog Output 3 Return
5 Analog Output 2 Current 5 Analog Output 4 Current
6 Analog Output 2 Return 6 Analog Output 4 Return
7 Analog Output 2 Voltage 7 Analog Output 4 Voltage
8 Analog Output 2 Return 8 Analog Output 4 Return
9 Isolated Ground 9 Isolated Ground
10 Isolated Ground 10 Isolated Ground
6 www.EmersonProcess.com/Remote
CWMICRO:AIO February 2012
Outputs
Quantity Four channels
Type Single-ended, jumper configurable as 1 to 5 Vdc or 4 to 20 mA
Resolution 12-bit
Over Range 0.8 to 5.2 Vdc or 3.2 to 20.8 mA
Reference Accuracy (after Current Output ±0.1% of span
calibration) at 25°C (77°F)
Voltage Output 0.1% + [0.114 * Iload in mA]% of span
Accuracy Over Operating Current Output ±0.3% of span
Temperature Range
[—40 to 70°C (—40 to 158°F)] Voltage Output 0.3% + [0.114 * Iload in mA]% of span
www.EmersonProcess.com/Remote 7
February 2012 CWMICRO:AIO
Headquarters:
Emerson Process Management
Remote Automation Solutions
6005 Rogerdale Road
Houston, TX 77072 U.S.A.
T +1 281 879 2699 | F +1 281 988 4445
www.EmersonProcess.com/Remote
Europe:
Emerson Process Management
Remote Automation Solutions
Emerson House
Kirkhill Drive Kirkhill Industrial Estate
Aberdeen UK AB21 OEU
T +44 1224 215700 | F +44 1224 215799
www.EmersonProcess.com/Remote
North American/Latin America:
Emerson Process Management
Remote Automation Solutions
6005 Rogerdale Road
Houston TX USA 77072
T +1 281 879 2699 | F +1 281 988 4445 © 2004-2012 Remote Automation Solutions, a business unit of Emerson Process
www.EmersonProcess.com/Remote Management. All rights reserved.
Middle East/Africa: Bristol, Inc., Bristol Canada, BBI SA de CV and Emerson Process Management Ltd, Remote
Emerson Process Management Automation Solutions (UK), are wholly owned subsidiaries of Emerson Electric Co. doing
Remote Automation Solutions business as Remote Automation Solutions, a business unit of Emerson Process Management.
Emerson FZE FloBoss, ROCLINK, Bristol, Bristol Babcock, ControlWave, TeleFlow and Helicoid are
P.O. Box 17033 trademarks of Remote Automation Solutions. AMS, PlantWeb and the PlantWeb logo are
Jebel Ali Free Zone — South 2 marks of Emerson Electric Co. The Emerson logo is a trademark and service mark of the
Dubai U.A.E. Emerson Electric Co. All other marks are property of their respective owners.
T +971 4 8118100 | F +971 4 8865465
The contents of this publication are presented for informational purposes only. While every
www.EmersonProcess.com/Remote
effort has been made to ensure informational accuracy, they are not to be construed as
Asia-Pacific: warranties or guarantees, express or implied, regarding the products or services described
Emerson Process Management herein or their use or applicability. Remote Automation Solutions reserves the right to modify
Remote Automation Solutions or improve the designs or specifications of such products at any time without notice. All sales
1 Pandan Crescent are governed by Remote Automation Solutions’ terms and conditions which are available
Singapore 128461 upon request. Remote Automation Solutions does not assume responsibility for the selection,
T +65 6777 8211| F +65 6777 0947 use or maintenance of any product. Responsibility for proper selection, use and maintenance
www.EmersonProcess.com/Remote of any Remote Automation Solutions product remains solely with the purchaser and end-user.