BMC Sub Engineer Syllabus
BMC Sub Engineer Syllabus
BMC Sub Engineer Syllabus
Sr. Topics
No.
1. Building Construction & Materials: Properties of wet and hardened concrete, tests on
concrete, factors affecting strength of concrete, water-cement ratio, aggregate-
cement ratio, mix design, additives, design of form work, types of formwork.
Stones, bricks, cements, lime, mortar, timber, plastic, concrete, steel, paints and
varnishes. Principles of building planning and design, integrated approach, building
byelaws, building services such as vertical transportation, water supply sanitation,
thermal ventilation, lighting, acoustics, fire protection, electrical fittings.
Foundations, stones, brick and block masonry, steel and reinforced cement concrete
structures, floors, doors and windows, roofs, finishing works, water proofing.
5. Design of reinforced concrete structures (Working stress and limit state): Design of
slab, beam, columns, footing, retaining walls, tanks, building frames, staircases.
11. Bridge Engineering: Selection of site, types of bridges, discharge, waterway, spans,
afflux, scour, standards, specifications, loads and forces, erection of superstructure,
strengthening.
b. Waste water Engineering & Pollution control: Quantity, collection and conveyance
and quality, disposal, design of sewer and sewerage systems, pumping,
characteristics of sewage and its treatment, rural sanitation, sources and affects of
air and noise pollution, monitoring, standards.
Sr. Topics
No.
2. Theory of Machines – Belt Drives, Gear Drives, Joints and Coupling, single and multi
cylinder engines and v engines, belt and chain drives, degree of freedom.
3. Machine Design Concepts – Torson, Spring, Joints, Bearing – types and Design, Theory
of Failure, Factor of Safety, Combined stresses, struts and columns, design of screw
and bolts, Design of Shafts and Springs, Keys.
4. Strength of material – stress strain analysis, Trusses and Trough, Shear Stress, Torsion,
bending moment and shear force concept, Shear force and bending moments in Beam,
Deflection of Beams and different conditions, shafts and helical springs, impact load,
torsion of bars
10. Transmission - Gear drive design and analysis, Stepped drive Vs Step less drive
11. Concept of SI and CI Engines – Carnot cycle, Reverse Carnot cycle, Rankin’s Cycle, Otto
cycle, Diesel cycle, SI Vs CI Engine
16. Electrical power transmission & distribution - Substation & receiving station, earthling,
substation equipment, Bus Bar, CT, PT, Protection relay numerical/ digital, circuit
breaker, onload isolator, offload isolator, Surge arrestor, system grounding, equipment
grounding, lightening protection etc. IS 3043, Single line diagram, control circuit,
ladder diagram (PLC).
17 Insulating material - Classification, dielectric strength, test & section (Bakelite, FRP,
Teflon, PVC, HDPE, Mica, SF6, Vacuum, Oil etc).
19 Cables and wires - Types, construction, HV/LV cables, testing, fault finding, cable
rating and selection, cable jointing, termination.
21 Illumination (Light) – Types of light, solar lighting, LED, CLF, HPSV,Mercury lamp, tube
light etc.
23 Power Electronics – SCR MOSFET, FET devices, rectifiers and invertor, SMPS, PWM
convertor, application.
28 Provision of National Building Codes on Building services & ventilation, electrical &
allied installation, air conditioning, ventilation, acoustic, sound insulation and noise
control, installation of lifts and escalators.
36 Data Transmission – Single, Half duplex, Full duplex, Fibre optic concept
41 Internet vs Intranet
Technical Syllabus for the post of Architect
Sr.No. Topics
Concept of T.P.S
Function of Arbitrator
Cost of Scheme
4 Building Permission
a)Building byelaws
b)Development
d)Measurement Plan
e)Layout of Land
f)F.S.I, TDR
g)Development charge
5 Transportation
Surveys
Classification of Roads
6 Environment Aspects
Surveys
7 Acts and Rules
LA Act. 1894