DFN 4043 - Practical Task 3
DFN 4043 - Practical Task 3
DFN 4043 - Practical Task 3
2.
3.
4.
Topology
Assessment Objectives
© 2017 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 1 of 11
CCNA: Routing and Switching Essentials
Scenario
In this Practical Task 3 you will configure a small network to support IPv4 connectivity, switch security and
inter VLAN routing. You will test and document the network using common CLI commands throughout the
assessment.
Instructor Note: For the initial SA setup, the routers should have a startup-configuration saved with a
hostname (Rtr). The router should also have a loopback address configured. The switches should have a
startup-configuration saved with a hostname (Sw) and have VLAN 99 created. These configurations will be
used to verify that the student initialized the devices correctly in Part 1, Step 1. It is recommended that these
configurations are saved to flash as SA_Init and used to reset the device for the next student.
Required Resources
1 Routers (Cisco 1941 with Cisco IOS Release 15.4(3)M2 universal image or comparable)
2 Switches (Cisco 2960 with Cisco IOS Release 15.0(2)SE7 lanbasek9 image or comparable)
2 PCs (Windows 7 or XP with terminal emulation program, such as Tera Term)
Console cable to configure the Cisco IOS devices via the console ports
Ethernet as shown in the topology
© 2017 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 2 of 11
CCNA: Routing and Switching Essentials
© 2017 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 3 of 11
CCNA: Routing and Switching Essentials
© 2017 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 4 of 11
CCNA: Routing and Switching Essentials
© 2017 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 5 of 11
CCNA: Routing and Switching Essentials
Step 3: Configure S3
© 2017 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 6 of 11
CCNA: Routing and Switching Essentials
Create the VLAN database Use Topology VLAN Key table to create and name each of (3 points)
the listed VLANS.
Assign the management IP address. Assign the IPv4 address to the Management VLAN. Use the (2 points)
IP address assigned to S1 in the Topology diagram.
Assign the default-gateway Assign the first IPv4 address in the subnet as the default- (1 point)
gateway.
Force trunking on Interface F0/3 Use VLAN 1 as the native VLAN. (3 points)
Force trunking on Interface F0/5 Use VLAN 1 as the native VLAN. (3 points)
Configure all other ports as access Use the interface range command. (2 points)
ports
Points: __________ of 18
© 2017 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 7 of 11
CCNA: Routing and Switching Essentials
Create the VLAN database Use Topology VLAN Key Table to create each of the listed (3 points)
VLANS. Name each VLAN.
Assign the management IP address Assign the IPv4 address to the Management VLAN. Use the (2 points)
IP address assigned to S3 in the Topology diagram.
Assign the default-gateway Assign the first IP address in the subnet as the default- (1 point)
gateway.
Force trunking on Interface F0/3 Use VLAN 1 as the native VLAN. (3 points)
Configure all other ports as access Use the interface range command. (2 points)
ports
Points: __________ of 15
© 2017 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 8 of 11
CCNA: Routing and Switching Essentials
Points: __________ of 11
© 2017 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 9 of 11
CCNA: Routing and Switching Essentials
Use the ping command to test connectivity between the switches and R1.
Use the following table to methodically verify connectivity with each network device. Take corrective action to
establish connectivity if a test fails:
Points: _________ of 16
Part 4: Cleanup
NOTE: DO NOT PROCEED WITH CLEANUP UNTIL YOUR INSTRUCTOR HAS GRADED YOUR SKILLS
EXAM AND HAS INFORMED YOU THAT YOU MAY BEGIN CLEANUP.
Before turning off power to the routers, remove the NVRAM configuration files (if saved) from all devices.
Disconnect and neatly put away all cables that were used in the final.
© 2017 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 10 of 11
CCNA: Routing and Switching Essentials
Router Model Ethernet Interface #1 Ethernet Interface #2 Serial Interface #1 Serial Interface #2
1800 Fast Ethernet 0/0 Fast Ethernet 0/1 Serial 0/0/0 (S0/0/0) Serial 0/0/1 (S0/0/1)
(F0/0) (F0/1)
1900 Gigabit Ethernet 0/0 Gigabit Ethernet 0/1 Serial 0/0/0 (S0/0/0) Serial 0/0/1 (S0/0/1)
(G0/0) (G0/1)
2801 Fast Ethernet 0/0 Fast Ethernet 0/1 Serial 0/1/0 (S0/1/0) Serial 0/1/1 (S0/0/1)
(F0/0) (F0/1)
2811 Fast Ethernet 0/0 Fast Ethernet 0/1 Serial 0/0/0 (S0/0/0) Serial 0/0/1 (S0/0/1)
(F0/0) (F0/1)
2900 Gigabit Ethernet 0/0 Gigabit Ethernet 0/1 Serial 0/0/0 (S0/0/0) Serial 0/0/1 (S0/0/1)
(G0/0) (G0/1)
Note: To find out how the router is configured, look at the interfaces to identify the type of router and how many
interfaces the router has. There is no way to effectively list all the combinations of configurations for each router
class. This table includes identifiers for the possible combinations of Ethernet and Serial interfaces in the device.
The table does not include any other type of interface, even though a specific router may contain one. An
example of this might be an ISDN BRI interface. The string in parenthesis is the legal abbreviation that can be
used in Cisco IOS commands to represent the interface.
© 2017 Cisco and/or its affiliates. All rights reserved. This document is Cisco Public. Page 11 of 11