CATIA V5 R16 Sketcher Models Manual
CATIA V5 R16 Sketcher Models Manual
CATIA V5 R16 Sketcher Models Manual
SKETCHER – 1
AIM: To draw the given 2D sketch using CATIA V5 R20 in sketcher module.
a. Profile
b. Sketch tools
c. Transformation
d. Predefined profile
e. Relimitations
PROCEDURE:
RESULT:
Thus the given 2D sketch was drawn and constrained geometrically and dimensionally in
SKETCHER module of CATIA V5 R20.
SKETCHER – 2
AIM: To draw the given 2D sketch using CATIA V5 R20 in sketcher module.
a. Profile
b. Sketch tools
c. Transformation
d. Predefined profile
e. Relimitations
PROCEDURE:
1. Select start Mechanical Design Sketcher.
2. XY Plane was selected.
3. Select Tools Options Parameters and measure Units set Length (mm), Angle (deg).
4. Three concentric circles, (“circle.1”, “circle.2”, “circle.3”) was drawn at origin (0,0) with diameters
(50, 68, 85) using “circle” tool in circle tool bar.
5. “Circle.2” with diameter 68 was converted into construction element using “construction/
Standard element” tool in Sketch tools tool bar.
6. A “circle.4” was drawn at (0, 68) with diameter 8.
7. “circle.4” was rotated with origin as center, with 6 instances and with 600 angle using “rotate” tool
in Transformation tool bar.
8. A “circle.10” was drawn at (0, -70) with diameter 22.
9. “Axis.1” line making an angle of 450 CW with respect to vertical was created.
10. “Arc.1” was drawn with origin as center and radius 70 using “Arc” tool in circle tool bar and was
converted into construction element.
11. A “circle.11” with diameter 22 was drawn at coincidence point of Axis.1 and Arc.1
12. A cylindrical elongated hole (say “CEH.1”) was created at (0,70) with radius 20 and angle
(+450CW, -450CCW) using “cylindrically elongated hole” in Predefined profile tool bar.
13. “circle.14” was created tangent to “circle.3” and “CEH.1” with radius 8 using “Three point circle”
in circle tool bar.
14. “circle.11” and “circle.14” was mirrored with respect to vertical axis to create “circle.15” and
“circle.16” using “mirror” tool in transformation tool bar
15. All the geometries that are not required was trimmed using “quick trim” tool in relimitations tool
bar.
16. All the geometries were constrained both dimensionally and geometrically with respect to
horizontal and vertical axis by using “constraints” tool bar.
RESULT:
Thus the given 2D sketch was drawn and constrained geometrically and dimensionally in
SKETCHER module of CATIA V5 R20.
SKETCHER – 3
AIM: To draw the given 2D sketch using CATIA V5 R20 in sketcher module.
a. Profile
b. Sketch tools
c. Transformation
d. Predefined profile
e. Relimitations
PROCEDURE:
1. Select start Mechanical Design Sketcher.
2. XY Plane was selected.
3. Select Tools Options Parameters and measure Units set Length (mm), Angle (deg).
4. Three concentric circles, (“circle.1”, “circle.2”, “circle.3”) was drawn at origin (0,0) with
diameters (28, 48, 70) using “circle” tool in circle tool bar.
5. “Circle.2” with diameter 48 was converted into construction element using “construction/
Standard element” tool in Sketch tools tool bar.
6. A “circle.4” was drawn at (48,0) with diameter 8.
7. “circle.4” was rotated with origin as center, with 6 instances and with 600 angle using “rotate” tool
in Transformation tool bar.
8. Two symmetrical circles (“circle.5”, “circle.6”) with center distance of 84 and diameter 18 was
drawn parallel to horizontal axis at a distance 72 from origin.
9. An elongated hole of radius 18 was drawn concentric with “circle.5” and “circle.6”.
10. A horizontal line “line.1” of length 84 was drawn at a distance of 102 from the origin.
11. Two symmetrical parallel vertical lines (“line.2”, “line.3”) with center distance 28 were drawn
tangent to “circle.2” and elongated hole.
12. The upper ends of “line.2”and “line.3” were cornered with radius 10 using “corner” tool in
operations tool bar.
13. The bottom ends of “line.2”and “line.3” were cornered with radius 8.
14. The ends of the “line.1” were cornered with radius 10 and made tangent to the elongated hole.
15. Two lines “line.4” and “line.5” were drawn tangent to the “circle.3 and on either sides elongated
hole.
16. All the geometries that are not required was trimmed using “quick trim” tool in relimitations tool
bar.
17. All the geometries were constrained both dimensionally and geometrically with respect to
horizontal and vertical axis by using “constraints” tool bar.
RESULT:
Thus the given 2D sketch was drawn and constrained geometrically and dimensionally in
SKETCHER module of CATIA V5 R20.
SKETHER – 4
AIM: To draw the given 2D sketch using CATIA V5 R20 in sketcher module.
a. Profile
b. Sketch tools
c. Transformation
d. Predefined profile
e. Relimitations
PROCEDURE:
RESULT:
Thus the given 2D sketch was drawn and constrained geometrically and dimensionally in
SKETCHER module of CATIA V5 R20.
SKETCHER – 5
AIM: To draw the given 2D sketch using CATIA V5 R20 in sketcher module.
a. Profile
b. Sketch tools
c. Transformation
d. Predefined profile
e. Relimitations
PROCEDURE:
RESULT:
Thus the given 2D sketch was drawn and constrained geometrically and dimensionally in
SKETCHER module of CATIA V5 R20.
SKETCHER – 6
AIM: To draw the given 2D sketch using CATIA V5 R20 in sketcher module.
a. Profile
b. Sketch tools
c. Transformation
d. Predefined profile
e. Relimitations
PROCEDURE:
RESULT:
Thus the given 2D sketch was drawn and constrained geometrically and dimensionally in
SKETCHER module of CATIA V5 R20.
SKETCHER – 7
AIM: To draw the given 2D sketch using CATIA V5 R20 in sketcher module.
a. Profile
b. Sketch tools
c. Transformation
d. Predefined profile
e. Relimitations
PROCEDURE:
RESULT:
Thus the given 2D sketch was drawn and constrained geometrically and dimensionally in
SKETCHER module of CATIA V5 R20.
SKETCHER – 8
AIM: To draw the given 2D sketch using CATIA V5 R20 in sketcher module.
a. Profile
b. Sketch tools
c. Transformation
d. Predefined profile
e. Relimitations
PROCEDURE:
RESULT:
Thus the given 2D sketch was drawn and constrained geometrically and dimensionally in
SKETCHER module of CATIA V5 R20.