CR 1
CR 1
CR 1
MAINTENANCE
INSTRUCTIONS
CR 1
Lombardini 15 LD 225
Robin EY 20
Honda GX 160
Weber Maschinentechnik GmbH
P.O. Box 21 53, D-57329 Bad Laasphe-Rückershausen
Phone ++27 54 / 398-0
0303-englisch
Please refer to the following page for the General Safety Instructions.
In chapter 1, the soil compactor is briefly described to provide you with a good overview on the location of the
individual assembly groups and their functions. Chapter 2 describes how to put the soil compactor into and out
of operation and how to work with the machine.
In chapter 3, you will find a survey on and a description of the required service work. Chapter 4 contains instructions
for trouble shooting by the operator. Chapter 5 describes how to preserve the soil compactor for an extended
storage, e.g. during the winter season.
We placed a great emphasis on a user-friendly lay-out with clear pictorial and textual information. In the text, you
will find figures in brackets which point out to illustrations, whereby the first figure indicates the figure number and
the second one - separated by a dash - indicates the item number on the corresponding illustration.
Important information for the operator and service personnel is highlighted by pictograms.
Indicates important information and hints which must be followed by the operator and service personnel.
Indicates working and operating methods requiring in addition the observance of all applicable environment
protection and waste disposal regulations.
Indicates working and operating methods which must be precisely followed in order to prevent the soil
compactor from being damaged or deteriorated.
Indicates working and operating methods which must be precisely followed in order to avert direct danger
to persons.
For further information, please contact your authorized WEBER distributor or one of the addresses on the last
page.
CR 1 3
General Safety Instructions
General
All safety notes (see also explanations of the pictogram meanings in the preface) must be read and observed (any
lack of clarity must be dispelled before the soil compactor is put into operation), because otherwise the use of the
machine may
* constitute a risk to life and limb of the user
* impair the machine and other valuable property.
In addition to these operating instructions and the mandatory accident prevention regulations in the country of use
and on the operating site, the generally accepted technical standards for a safe and professional work must be
also observed.
Designated Use
Soil compactors are only allowed to be operated in accordance with their designated use, whereby the operating
and maintenance instructions, the generally accepted safety and traffic regulations and the regulations of the
individual countries of use must be followed:
The soil compactor has been exclusively designed for the compaction of
- sand
- gravel
- crushed stone
- semi-cohesive mixed aggregates
- concrete block pavement
Any other use of the soil compactor is considered contrary to its designated use. The owner of the soil compactor
bears the sole responsibility for any misuse of the machine.
Driving Permission
Only trustworthy persons, who are aged at least 18 years, are allowed to handle soil compactors. They must be
properly trained in the operation and maintenance of the soil compactor by the owner or his authorized
representative.
Protective Equipment
When operating the soil compactor described in this operation and maintenance manual, the noise level at the
operator's ear may exceed 90 dB(A). The German noise protection regulations (VBG 121) require the operator
to wear personal ear protectors in case of noise levels of 90 dB(A) and more.
Additionally, a safety helmet and safety shoes belong to the protective equipment.
4 CR 1
Table of Contents
Preface ................................................................................................................................................................................ 3
General Safety Instructions ............................................................................................................................................... 4
1. Technical Description ..................................................................................................................................................... 6
1.1 Illustration .................................................................................................................................................................. 6
1.2 Machine Description ................................................................................................................................................... 7
1.3 Specifications ............................................................................................................................................................... 8
2 Operation ....................................................................................................................................................................... 10
2.1 Safety Precautions for the Operation ........................................................................................................................ 10
2.2 Transport .................................................................................................................................................................... 11
2.2.1 Loading by Crane ................................................................................................................................................... 11
2.3 Commissioning .......................................................................................................................................................... 11
2.4 Pre-Start Work ............................................................................................................................................................ 12
2.4.1 Checking the Fuel Level, Lombardini Engine ...................................................................................................... 12
2.4.1.1 Checking the Fuel Level, Robin/ Honda Engine ............................................................................................... 13
2.4.2 Checking the Engine Oil Level ............................................................................................................................... 14
2.4.2.1 Lombardini Engine ............................................................................................................................................... 14
2.4.2.2 Robin/Honda Engine ............................................................................................................................................ 14
2.4.3 Fitting the Damper Plate ......................................................................................................................................... 15
2.4.4 Fixing the Undercarriage ........................................................................................................................................ 16
2.5 Starting ....................................................................................................................................................................... 17
2.5.1 Starting, Lombardini Engine ................................................................................................................................... 17
2.5.1.2 Starting, Robin Engine ......................................................................................................................................... 18
2.5.1.3 Starting, Honda Engine ........................................................................................................................................ 19
2.6 Compaction Work ...................................................................................................................................................... 20
2.7 Putting the Soil Compactor Out of Operation ......................................................................................................... 20
2.7.1. Stopping, Lombardini Engine ............................................................................................................................... 21
2.7.1.1 Stopping, Robin Engine ...................................................................................................................................... 21
2.7.1.2 Stopping, Honda Engine ..................................................................................................................................... 22
3 Maintenance ................................................................................................................................................................... 23
3.1 Safety Precautions for Maintenance Work ............................................................................................................... 23
3.2 Maintenance Survey ................................................................................................................................................... 24
3.2.1 Initial Maintenance .................................................................................................................................................. 24
3.2.2 Routine Maintenance .............................................................................................................................................. 25
3.3 Description of the Maintenance Work ...................................................................................................................... 26
3.3.1. Changing the Engine Oil, Lombardini Engine ..................................................................................................... 26
3.3.1.1 Cleaning the Engine Oil Filter, Lombardini Engine ............................................................................................ 27
3.3.1.2 Changing/Adding Engine Oil - Robin/Honda Engine ........................................................................................ 28
3.3.2 Cleaning/Replacing the Air Filter Cartridge ........................................................................................................... 29
3.3.2.1 Lombardini Engine ............................................................................................................................................... 29
3.3.2.2 Robin Engine ........................................................................................................................................................ 29
3.3.2.3 Honda Engine ....................................................................................................................................................... 30
3.3.3 Replacing the Fuel Filter ......................................................................................................................................... 31
3.3.3.1 Lombardini Engine ............................................................................................................................................... 31
3.3.3.2 Robin Engine ........................................................................................................................................................ 31
3.3.4 Checking the Condition and Tension of the Vibrator V- Belt .............................................................................. 32
3.3.5 Replacing the V-Belt ................................................................................................................................................ 32
3.3.6 Changing the Vibrator Oil ...................................................................................................................................... 33
3.4 Consumables and Quantities ................................................................................................................................... 34
4 Malfunctions During Operation .................................................................................................................................... 35
4.1 General ........................................................................................................................................................................ 35
4.2 Trouble Shooting ....................................................................................................................................................... 36
5 Preserving the Machine ............................................................................................................................................... 37
5.1 Preservation Measures .............................................................................................................................................. 37
5.2 Removing Machine Preservatives ............................................................................................................................ 37
6 Weber Maschinentechnik GmbH ................................................................................................................................. 38
CR 1 5
1 Technical Description
1.1 Illustration
2 12
3
4
11
1
5
10 7
9 6
1 Engine 9 Vibrator
2 Drive lever 10 V-belt protection
3 Handle 11 Spring bar
4 Lifting lug 12 Speed adjusting lever
5 Reversible starter 13 Vulkollan plate (not shown)
6 Base plate
7 Protection frame
8 Engine bracket
6 CR 1
1.2 Machine Description
The CR 1 soil compactors are machines of the walk-behind type used for compaction work in road
construction and landscape applications.
Propulsion
The CR 1 is driven by a Lombardini Diesel engine or a Robin or Honda gasoline engine.
Important!
Please refer to paragraph 1.3 (Specifications) for performance details of the engine and the
whole machine.
Function
The engine (1/1) drives the vibrator via a V-belt. The vibrator is screwed down to the base plate (1/6) and
sets it vibrating. The vibrating base plate performs the vibration work and travelling motion.
Accessories
A damper plate (2.4.3) is available as optional extra.
Operation
The soil compactor is started by means of a reversible starter (1/5). The machine is steered with the handle
(1/3) holding the lever (1/12) for the engine speed adjustment and the drive lever (1/2) for the selection of the
direction of travel and of the infinitely variable speed. The spring bar (1/11) allows to lock the handle in vertical
position during working breaks and when the machine is transported.
CR 1 7
1.3 Specifications
CR 1 CR 1 R CR 1 HD
Weight
Operating weight CECE in kg 118 105 105
Dimensions
Height with handle folded down (in mm) 1039 1039 1039
Propulsion
Max. output acc. to DIN 70020(in kW (HP)) 3,5/4,7 at 3600 3,4/4,6 at 3600 4,0/5,5 at 3600
Type of combustion 4-stroke Diesel 4-stroke Gasoline 4-stroke Gasoline
Engine speed 3000 3000 3000
Vibration
8 CR 1
CR 1 CR 1 Robin CR 1 Honda
Hand/arm vibration
(Weighted root mean square acceleration, at the
5 to 10 5 to 10 5 to 10
handle, determined according to 2002/44/EG,
Part 1, in m/s²)
* The indicated noise and vibration data were determined with the engine at nominal speed and the vibration
system turned on, 2000/14/EG. During operation, these data may vary according to the specific conditions
prevailing on the job site.
Typ Masch.-Nr.
Betriebsgewicht Baujahr
3
1 2
Weber Maschinentechnik GmbH
Postfach 2153
57329 Bad Laasphe-Rückershausen
.................................................... ...................................................
.................................................... ....................................................
CR 1 9
2 Operation
2.1 Safety Precautions for the Operation
Before starting the soil compactor, the operator must take his personal noise protection measures. The engine
is only allowed to be started after it has been assured that the soil compactor cannot automatically start moving.
Stability
Soil compactors must be used and operated in a way ensuring their stability. The machine's stability is especially
endangered on slopes and brinks. Thus, keep clear of slopes and brinks.
Moist and loose bases considerably reduce the grip of the soil compactor on slopes. Increased danger
of accident!
Passing unevennesses or kerbs is only allowed at reduced speed. In addition, the soil compactor must be
operated in a way excluding any risk of injury caused by the handle swinging towards the operator.
Exhaust Precautions
Never inhale exhaust gasses. They contain carbon monoxide, a colorless, oderless and extremely dangerous
gas which can cause unconsciousness or death. Never operate the engine inddors or in a poorly ventilated area,
such as tunnerl, cave, etc. Exercise extreme care when operating the engine near people or animals. Keep the
exhaust pipe free of foreign objects.
10 CR 1
2.2 Transport
Short distances on the job site can be covered by the soil
compactor in accordance with paragraph 2.6.
Danger!
Never use the handle (2/1) for lifting the machine by crane.
The machine may overturn.
2
- Put the crane hook (2a/1) into the protection frame (2a/2).
Danger! Figure 2
Only use a lifting tackle and a crane of a sufficient bearing
capacity.
Danger!
Do not enter the zone under the suspended load.
1
Figure 2 a
2.3 Commissioning
Caution!
For commissioning, only carry out the pre-start work described in paragraph 2.4.
Keep to the initial maintenance intervals (refer to paragraph 3.2.1).
CR 1 11
2.4 Pre-Start Work
- Check to ensure that all safety devices are in place.
- Check the whole soil compactor for evident damage (visual check).
- Check all screwed connections for tight seat, retighten them if necessary.
- Check the fuel level, if necessary, add fuel (refer to paragraph 2.4.1).
- Check the engine oil level, if necessary add engine oil (refer to paragraph 2.4.2).
- If required, fit the damper plate (refer to paragraph 2.4.3)
Caution!
Fill the tank up with clean Diesel fuel only. Refer
to paragraph 3.4 for quantities and specifications..
Danger!
Take care that fuel does not come in contact with
hot engine parts. Do not smoke. Extinguish all
2
open flames while filling the tank.
1
Environment Hazard!
Always wipe up any spilled fuel. Dispose of fuel-
soaked cloth in an environmentally-friendly
manner.
- Firmly close the fuel tank (3/1) with the filler cap (3/2).
Figure 4
12 CR 1
2.4.1.1 Checking the Fuel Level, Robin/
Honda Engine
Caution!
2
Fill the tank up with clean regular gasoline
only. Refer to paragraph 3.4 for quantities Figure 3 a
and specifications
Danger!
Take care that fuel does not come in contact with
hot engine parts. Do not smoke. Extinguish all
open flames while filling the tank.
1
Environment Hazard!
Always wipe up any spilled fuel. Dispose of Figure 4 a
fuel-soaked cloth in an environmentally-
friendly manner.
- Firmly close the fuel tank with the filler cap (3a/1).
CR 1 13
2.4.2 Checking the Engine Oil Level
2.4.2.1 Lombardini Engine
Caution!
The engine oil level must be checked with the soil compactor
standing horizontally on the ground.
- Pull out the oil filler screw by means of the oil dipstick (5/1), wipe
it off with a clean, non-fluffing cloth and insert it again.
Caution!
1
-Screw the oil dipstick (5/1) down.
Figure 5 max.
-Undo the oil dipstick once again.
Caution!
The oil level must reach up to the top mark
(5/max).
- Pull out the oil filler screw by means of the oil dipstick
(5a/1), wipe it off with a clean, non-fluffing cloth and
insert it again.
1
Caution!
Do not screw down!!
Figure 5 a
- Pull out the oil dipstick once again.
Caution!
The oil level must reach up to the top mark min. max.
(5b/max).
14 CR 1
2.4.3 Fitting the Damper Plate
- Put the soil compactor out of operation as described in
paragraph 2.7.
- Lift the soil compactor by means of a crane according to 2
paragraph 2.2.1. 4
Caution! 1 3
Do not enter the zone under the suspended load! Figure 6
Risk of injury!
- Fix the Vulkollan plate (6/1) with the support (6/2) and
the screw (6/3) on the base plate (6/4) as shown.
- Attach the Vulkollan plate (6a/1) with the support (6a/2)
and the screws (6a/3) at the back. 2
Important!
Check to ensure that the Vulkollan plate is correctly
Figure 6a 3
fitted beneath the base plate. If the Vulkollan plate 1
is not correctly fitted, realign it according to the
description.
CR 1 15
2.4.4 Fixing the Undercarriage
- Put the soil compactor out of operation as described in paragraph
2.7.
- Arrest the handle (6c/2) by means of the locking lever (6c/1).
- Attach the locking pin (6d/1) to the engine bracket (6d/2).
- Use the handle (6e/1) to lift the soil compactor at the back.
1
- Push the undercarriage (6e/2) beneath the base plate (6e/4) by
means of the drawbar (6e/3).
- The locking pin (6f/1) must sit in the iron support (6f/2) of the 2
undercarriage.
- Use the handle (6e/3) to pull the soil compactor into the desired Figure 6c
direction.
Warning!
Check to ensure that the locking pin (6f/1) properly engages 2
with the iron support (6f/2). If the locking pin is not correctly
fitted, the soil compactor may work loose from the
undercarriage. – Risk of injury because of sliding soil
compactor! –
1
Figure 6d
2 4
Figure 6e
2
Figure 6f
16 CR 1
2.5 Starting
Danger!
Before starting the machine, always ensure 1
that nobody is in the danger area of the soil
compactor and that all protective devices are
properly in place.
Caution!
Never use starting aid sprays!
Figure 7
2.5.1 Starting, Lombardini Engine
- Put the speed adjusting lever (7/1) into the full speed position.
- Slowly pull the handle (8/1) of the reversible starter (8/2) until a resistance
is felt. 2
1
- Let the handle (8/1) recoil into its original position and then firmly pull the
cable with both hands to start the engine.
Important!
If the engine fails to start, repeat the starting procedure.
- As soon as the engine starts, let the starter cable return into its housing Figure 8
(8/2).
- Let the engine idle for some minutes.
Important!
In case of ambient temperatures of 5 degrees C below zero, the
starting procedure must be carried out in accordance with the
operation manual of the engine manufacturer.
CR 1 17
2.5.1.2 Starting, Robin Engine
- Turn the stop button (9/1) to the right into the „On“
position.
- Put the speed adjusting lever (11/1) into the full 1
speed position.
- Put the fuel stop cock (11/1) into the vertical
position to open it.
- Open or close the choke (10/1) according to the
engine and/or ambient temperature.
a) In case of a cold engine and/or low ambient
Figure 9
temperatures, totally close the choke (10/1). (Pull
the choke lever).
b) In case of a warm engine and/or high ambient
temperatures, open the choke (10/1) half to all the
way (push the choke towards the engine housing).
- Slowly pull the handle (12/1) of the reversible
starter (12/2) until a resistance is felt.
- Let the handle (12/1) recoil into its original position
and then firmly pull the cable with both hands to
start the engine. 1
Figure 10
Important!
If the engine should fail to start, repeat the
starting procedure.
Figure 11
Figure 12
18 CR 1
2.5.1.3 Starting, Honda Engine
Important!
If the engine should fail to start, repeat the 1
starting procedure.
Figure 14
- As soon as the engine starts, let the starter cable
recoil into its housing (15/2).
- Slowly bring the choke (14/2) into the fully open
position (choke to the right side) and let the engine
idle for warming up.
1
Figure 15
CR 1 19
2.6 Compaction Work
Caution! 2
Compaction work is only allowed to be done at full engine speed,
otherwise the centrifugal clutch may slip and cause increased wear.
Important!
As soon as the centrifugal clutch achieves the cutting-in speed, the
vibrator is automatically turned on. Figure 16
Danger!
If obstructions (such as walls or trenches) are encountered, take care that
persons do not get crushed and that the machine does not slip out of
control.
Warning!
During working breaks, even if they are short, the soil compactor must be
put out of operation (refer to 2.7).
- Steer the soil compactor with the handle (16/1) into the desired direction.
Before work breaks and at the end of every day’s shift, the soil compactor must
be parked on a stable base which should be as horizontal as possible.
Warning!
If the soil compactor causes an obstruction when being parked,
precautionary measures must be taken in order to make the machine
visible. If the machine is parked on traffic roads, the safety precautions
required by the traffic regulations must be additionally observed.
Caution!
Never stop the engine while it is running at full speed, but let the engine
idle for some minutes.
20 CR 1
2.7.1. Stopping, Hatz Engine
- Push the speed adjusting lever (17/1) to the back and let the engine
idle for some minutes. 1
- Stop the engine by fully pulling the speed adjusting lever to the back.
Figure 17
- Push the speed adjusting lever (17/1) to the back and let the engine
idle for some minutes. 1
- Close the fuel cock (18/1).
- Turn the stop button (19/1) into the "Off" position.
Figure 18
Figure 19
CR 1 21
2.7.1.2 Stopping, Honda Engine
- Push the speed adjusting lever (20/1) to the back and let the 1
engine idle for some minutes.
- Close the fuel cock (21/1) (position "O").
- Turn the stop button (22/1) into the "Stop" position.
Figure 20
Figure 21
Figure 22
22 CR 1
3 Maintenance
3.1 Safety Precautions for Maintenance Work
Checks
Depending upon the operating conditions, soil compactors must be made subject to an expert's check for
operational safety when required, but at least once a year. The inspection results must be recorded in writing
and kept at least until the next inspection.
Service Work
Service work is only allowed to be done when the drives are stopped. Exceptions are only allowed if work
can be done with running drives only. In addition, the soil compactor must be secured against unintentional
movements.
Drained off consumables must be collected and stored in an appropriate receptacle and disposed
off according to the relevant environmental protection regulations.
Prior to any work on parts which are not protected, the engine must be secured against unintentional starting.
After completion of service work, all protective devices must be properly installed again.
CR 1 23
3.2 Maintenance Survey
Any maintenance work which must be performed on the soil compactor is listed in two charts. The first chart (paragraph
3.2.1) indicates the initial maintenance work which has to be carried out once at a certain time after commissioning.
The routine maintenance work indicated in the second chart (paragraph 3.2.2) has to be repeated at regular intervals.
Both charts have the same lay-out. The column "Maintenance Interval" indicates the time or the operating hours at
which (after which) the maintenance work must be done.
The column "Maintenance Item" refers to the assembly group on which the work indicated in the column "Maintenance
Work" must be carried out.
The column "Remarks" contains cross-references on paragraphs of these operating and maintenance instructions or
other documentation in which the maintenance work is described in detail.
24 CR 1
3.2.2 Routine Maintenance
Every 500 operating Diesel engine - Change the engine oil # 3.3.1
hours
- Check and adjust the valve Manual of the engine
clearance manufacturer
- Clean the cooling air area "
- Clean the exhaust strainer "
Vibrator - Change the oil # 3.3.6
Robin/Honda engine - Clean and if necessary adjust Manual of the engine
the carburettor manufacturer
- Clean the cylinder head "
- Adjust the valve clearance "
Engine - Change the fuel filter # 3.3.3
- Change the air filter
# 3.3.2
Every 1000 operating Whole soil compactor - Check all components for
hours visible damage and wear
CR 1 25
3.3 Description of the Maintenance Work
3.3.1. Changing the Engine Oil, Lombardini Engine
1
- Put the soil compactor out of operation as
described in paragraph 2.7.
Caution!
Drain off the engine oil at operating
tempertature and with the soil compactor
standing horizontally on the ground only.
Figure 23
- Put a drain pan under the outlet.
Environment Hazard!
Choose a drain pan having a sufficient capacity
to catch all the used oil. Do not let used oil run
into the soil. Dispose of the collected used oil
in an environmentally-friendly manner (acc.
to statutory pollution control regulations).
Danger! Figure 24
Danger of scalding because of hot oil.
26 CR 1
3.3.1.1 Replacing the Engine Oil Filter, Lombardini
Engine
Environment Hazard!
Wipe up any oil and dispose of the oil filter and
the oil-soaked cloth in an environmentally-
friendly manner. 1
- Top up with engine oil according to paragraph 3.3.1.
Caution!
Make a short trial run and check for tightness,
if required, retighten the screws. Figure 26
Figure 26a
CR 1 27
3.3.1.2 Changing/Adding Engine Oil -
Robin/Honda Engine
Environment Hazard!
Choose a drain pan having a sufficient capacity
to catch all the used oil. Do not let used oil run
into the soil. Dispose of the collected used oil
in an environmentally-friendly manner (acc.
to statutory pollution control regulations).
1
Wipe up any oil residues and dispose of the
oil-soaked cloth in an environmentally-friendly
manner.
Danger! Figure 28
28 CR 1
3.3.2 Cleaning/Replacing the Air Filter Cartridge
3.3.2.1 Lombardini Engine
- Undo the two snap clips (29/1) and remove the cover (29/2) from 1
the air filter body.
- Pull the air filter element (30/1) out of the air filter housing (30/2)
and blow or knock it clean.
2
Caution!
- Undo the two snap clips (29/2) and remove the cover (29/1)
from the air filter body.
Caution!
3
- Pull the air filter element (31/1) out of the air filter housing (31/2)
and blow or knock it clean.
Figure 32
CR 1 29
3.3.2.3 Honda Engine
2
- Remove the wing nut (33/2) and the air filter cover (33/1).
- Pull out the air filter element (34/1) and the foam pre-cleaner (35/2).
- Wash the foam pre-cleaner (34/2) in benzine and let it dry.
Environment Hazard
1
- Knock or blow the air filter element (35/1) clean.
Figure 33
Caution!
- Insert the filter (35/1) again and fasten it with the wing nut (35/2).
- Fit the air filter cover (33/1) with the wing nut (33/2). 2
Figure 34
Figure 35
30 CR 1
3.3.3 Replacing the Fuel Filter
3.3.3.1 Lombardini Engine 1
- Put the soil compactor out of operation as described in
paragraph 2.7. 2
- Undo the clips (36/2), remove the diesel fuel lines (36/1) 3
from the fuel filter (36/3) and completely drain the tank.
- Remove the clip (36/4) from the fuel filter (36/3) and replace
the used filter by a new one.
4 2
- Put the fuel lines (36/1) on the fuel filter and fasten them
with the clips (36/2).
Figure 36
Make sure that the clips are correctly fastened and check the
system for tightness.
Environment Hazard!
Immediately wipe up any escaping fuel, dispose of the
fuel-soaked cloth in an environmentally-friendly 2
manner.
1
Figure 39
CR 1 31
3.3.4 Checking the Condition and Tension of the Vibrator V-
Belt
Caution!
Take care to properly fit the V-belt on the pulleys (belt alignment).
Figure 40
Due to the special centrifugal clutch, the V-belt is tensioned.
Figure 41
- Remove the upper V-belt guard (40/2) and the bottom V-belt guard (42/ 2
2
1) by loosening the screws (40/1 and 42/2).
- Put on the new V-belt (41/1). 1
Caution! Figure 42
Take care to properly align the belt, especially after repair work.
32 CR 1
3.3.6 Changing the Vibrator Oil
Caution! 1
Change the oil at operating temperature only.
- Park the soil compactor so that the oil drain screw (44/2) is easily
accessible.
2
Caution!
Thouroughly clean the oil drain screw
(44/2) and the area around the drain outlet. Figure 44
Caution!
Take care that the contact surfaces of the oil drain screw and
of the vibrator housing are clean.
Environment Hazard!
Dispose of the collected used oil in an environmentally-friendly
manner. Take care that the environment is not polluted by oil.
CR 1 33
3.4 Consumables and Quantities
Engine
Engine oil SAE 10 W 40 0,7 l 0,6 l 0,6 l
(-10 ~ + 50 °C)
API - CD CE-CF-CG
or SHPD
or CCMC - D4 - D5 - PD2
Diesel 3,0 l
Diesel acc. to DIN 51601-DK
Fuel tank or BS2869-A1/A2
or STM D975-1D/2D
34 CR 1
4 Malfunctions During Operation
4.1 General
Please refer to the manual of the engine manufacturer with regard to the repair of engine
malfunctions.
The detailed description of the various controls and the references given in the column "Remarks/Notes"
of the maintenance survey chart (paragraph 3) and trouble shooting chart (paragraph 4.2) allows a quick
failure elimination on condition that the given order is precisely kept to when service work is carried out.
Any service work has to be made with appropriate tools and in accordance with the safety
regulations set out in this operating and maintenance manual.
If a problem persists although a component or assembly group has been replaced, repair work has to be
continued with the work described next. If a failure cannot be rectified although the described service work
has been carried out or if a defect is not described in the operating and maintenance instructions, the failure
must be repaired by authorized service personnel.
CR 1 35
4.2 Trouble Shooting
If the soil compactor is to be stored for more than 6 months, additional measures must be taken in
accordance with your WEBER service.
Fuel tank - Add fuel up to the bottom edge of the filler neck # 2.4.1
For problems, questions and further information refer to one of the following addresses:
E-Mail g.voelkel@webermt.de